TY1250I-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
121
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
121 total| Object Name |
|---|
tylink OBJECT IDENTIFIER .1.3.6.1.4.1.466 |
RFC-1215 Unknown .1.3.6.1.4.1.466 |
dsucsu OBJECT IDENTIFIER .1.3.6.1.4.1.466.1 |
tyview OBJECT IDENTIFIER .1.3.6.1.4.1.466.2 |
ty1250 OBJECT IDENTIFIER .1.3.6.1.4.1.466.3 |
ty1250TrapA ty1250Trap trap signifies that the
sending node had its `ty1250AlarmType`
variable modified. TRAP-TYPE .1.3.6.1.4.1.466.3.0.0 |
ty1250LineFailureTrapThe line has failed. TRAP-TYPE .1.3.6.1.4.1.466.3.0.1 |
ty1250LineInServiceTrapThe line is back in service. TRAP-TYPE .1.3.6.1.4.1.466.3.0.2 |
ty1250ConnectedTrapThe 1250 unit is connected. TRAP-TYPE .1.3.6.1.4.1.466.3.0.3 |
ty1250ConnectFailureTrapThe attempted connection failed. TRAP-TYPE .1.3.6.1.4.1.466.3.0.4 |
ty1250IncomingCallTrapIncoming call. TRAP-TYPE .1.3.6.1.4.1.466.3.0.5 |
ty1250DisconnectedTrapDisconnected. TRAP-TYPE .1.3.6.1.4.1.466.3.0.6 |
ty1250BadConfigTrapThe configuration specified in the
SET command was bad. SET failed. TRAP-TYPE .1.3.6.1.4.1.466.3.0.7 |
ty1250LocalConfigTrapThe configuration has been changed
by a means other than SNMP. TRAP-TYPE .1.3.6.1.4.1.466.3.0.8 |
ty1250BPVThresholdExceededTrapBPV threshold exceeded. TRAP-TYPE .1.3.6.1.4.1.466.3.0.9 |
ty1250BPVThresholdAcceptableTrapBPV threshold acceptable. TRAP-TYPE .1.3.6.1.4.1.466.3.0.10 |
ty1250LocalUnitLoopbackEnabledTrapLocal unit loopback enabled. TRAP-TYPE .1.3.6.1.4.1.466.3.0.11 |
ty1250LocalUnitLoopbackDisabledTrapLocal unit loopback disabled. TRAP-TYPE .1.3.6.1.4.1.466.3.0.12 |
ty1250LocalNetLoopbackEnabledTrapLocal network loopback enabled. TRAP-TYPE .1.3.6.1.4.1.466.3.0.13 |
ty1250LocalNetLoopbackDisabledTrapLocal network loopback disabled. TRAP-TYPE .1.3.6.1.4.1.466.3.0.14 |
ty1250SimplexCurrentLoopbackEnabledTrapSimplex current loopback enabled. TRAP-TYPE .1.3.6.1.4.1.466.3.0.15 |
ty1250SimplexCurrentLoopbackDisabledTrapSimplex current loopback disabled. TRAP-TYPE .1.3.6.1.4.1.466.3.0.16 |
ty1250NonLatchingLoopbackEnabledTrapNonlatching loopback enabled. TRAP-TYPE .1.3.6.1.4.1.466.3.0.17 |
ty1250NonLatchingLoopbackDisabledTrapNonlatching loopback disabled. TRAP-TYPE .1.3.6.1.4.1.466.3.0.18 |
ty1250V54LoopUpInitiatedTrapStarting to loop up a V54 loopback on the remote unit. TRAP-TYPE .1.3.6.1.4.1.466.3.0.19 |
ty1250V54LoopDownCompletedTrapCompleted the loop down of a V54 loopback on the remote unit. TRAP-TYPE .1.3.6.1.4.1.466.3.0.20 |
ty1250V54LoopbackEnabledTrapV54 loopback enabled by remote unit. TRAP-TYPE .1.3.6.1.4.1.466.3.0.21 |
ty1250V54LoopbackDisabledTrapV54 loopback disabled by remote unit. TRAP-TYPE .1.3.6.1.4.1.466.3.0.22 |
ty1250BertInitiatedTrapBERT test pattern initiated. TRAP-TYPE .1.3.6.1.4.1.466.3.0.23 |
ty1250BertCompletedTrapBERT test pattern completed. TRAP-TYPE .1.3.6.1.4.1.466.3.0.24 |
ty1250LocalDteLoopbackEnabledTrapLocal DTE loopback enabled. TRAP-TYPE .1.3.6.1.4.1.466.3.0.25 |
ty1250LocalDteLoopbackDisabledTrapLocal DTE loopback disabled. TRAP-TYPE .1.3.6.1.4.1.466.3.0.26 |
ty1250LocalUnitLoopbackFailedTrapUnable to do a local unit loopback. TRAP-TYPE .1.3.6.1.4.1.466.3.0.27 |
ty1250LocalNetLoopbackFailedTrapUnable to do a local network loopback. TRAP-TYPE .1.3.6.1.4.1.466.3.0.28 |
ty1250BertFailedTrapUnable to do a BERT. TRAP-TYPE .1.3.6.1.4.1.466.3.0.29 |
ty1250LocalDteLoopbackFailedTrapUnable to do a local DTE loopback. TRAP-TYPE .1.3.6.1.4.1.466.3.0.30 |
ty1250V54LoopbackFailedTrapUnable to do a V54 loopback. TRAP-TYPE .1.3.6.1.4.1.466.3.0.31 |
ty1250SysTable OBJECT IDENTIFIER .1.3.6.1.4.1.466.3.1 |
ty1250SysTypeA textual description of the system model identifier.
for example: TYLINK1250ro DisplayString .1.3.6.1.4.1.466.3.1.1 |
ty1250SysSoftRevDisplays the Software Revision installed in this node.ro DisplayString .1.3.6.1.4.1.466.3.1.2 |
ty1250SysHardRevDisplays the Hardware Revision of the node.ro DisplayString .1.3.6.1.4.1.466.3.1.3 |
ty1250SysNumNetInstalledThe number of Network (DDS) ports that are
installed. There is 1 on the 1250.ro INTEGER .1.3.6.1.4.1.466.3.1.4 |
ty1250SysNumDteInstalledThe number of channels (DTE) that are
installed. There is 1 on the 1250.ro INTEGER .1.3.6.1.4.1.466.3.1.5 |
ty1250SysNumMaintInstalledThe number of Maintenance ports that are
installed. There are 2 on the 1250.ro INTEGER .1.3.6.1.4.1.466.3.1.6 |
ty1250SysNameThe user supplied name of the node. This object
does not affect operation, but may be useful
for network management.rw DisplayString .1.3.6.1.4.1.466.3.1.7 |
ty1250CfgAppTable OBJECT IDENTIFIER .1.3.6.1.4.1.466.3.2 |
ty1250CfgAppClockSourceDefault timing, or clock, source. There must be only one
source on a DDS line. Node should always be network (2)
timed on a point-to-network application. Line
Driver applications need one node as internal (1),
one as network (2).rw Enumeration .1.3.6.1.4.1.466.3.2.2 |
ty1250CfgAppCircuitIdCircuit identifier provided by the service provider.rw DisplayString .1.3.6.1.4.1.466.3.2.3 |
ty1250CfgNetTable OBJECT IDENTIFIER .1.3.6.1.4.1.466.3.3 |
ty1250CfgNetGlareTypeIn switched applications, defines who wins when
there are simultanious incomming and outgoing
calls. If in doubt, select external-glare (2).rw Enumeration .1.3.6.1.4.1.466.3.3.4 |
ty1250CfgNetEchoCanIn switched applications, some carriers, such
as Sprint, require you to disable-echo-cancellors (2)
for data apps on most lines. Calls take longer
to come up when disabling is done; use
ignore-echo-cancellers (1) on clear channel lines.rw Enumeration .1.3.6.1.4.1.466.3.3.5 |
ty1250CfgNetAnsModeIn switched applications, allows for manual-answer (1)
or automatic-answer (2) of inbound calls. Calls
may be answered in manual mode via vt100, DTR, or the
front panel button if so configured.rw Enumeration .1.3.6.1.4.1.466.3.3.6 |
ty1250CfgNetDialTimeoutIn switched applications, time in seconds to wait
for far end to answer before giving up, and possibly
redialing.rw INTEGER .1.3.6.1.4.1.466.3.3.7 |
ty1250CfgNetNumRedialIn switched applications, number of times to
redial if the call fails.rw INTEGER .1.3.6.1.4.1.466.3.3.8 |
ty1250CfgNetRedialDelayIn switched applications, delay in seconds
between redial attempts.rw INTEGER .1.3.6.1.4.1.466.3.3.9 |
ty1250CfgNetDefNum2DialIn switched applications, default phone number
to dial. Numbers and dashes are allowed.rw DisplayString .1.3.6.1.4.1.466.3.3.10 |
ty1250CfgNetTypeIndicates type of service purchased on the attached
network line (DDS or SW56). Valid selections are
dedicated (1) and switch56 (2).rw Enumeration .1.3.6.1.4.1.466.3.3.11 |
ty1250CfgNetBPVThresholdingAllows the user to turn on and off the BPV thresholding
function. Valid values are thresholding_at_10E-4 (1) and
disable-thresholding (2).rw Enumeration .1.3.6.1.4.1.466.3.3.12 |
ty1250CfgDteTable OBJECT IDENTIFIER .1.3.6.1.4.1.466.3.4 |
ty1250CfgDteTypeThe Dte channel type identifies the electrical
specification of the interface. Read-only.ro Enumeration .1.3.6.1.4.1.466.3.4.1 |
ty1250CfgDteClockInvertClock Inversion, invert-dte-clock (2), can be
used to solve out of phase timing problems on
DTE link. normal-dte-clock (1) can be used in
most cases.rw Enumeration .1.3.6.1.4.1.466.3.4.5 |
ty1250CfgDteTimingThe DTE channel Timing mode. Use loop2-timing (2)
when in doubt.rw Enumeration .1.3.6.1.4.1.466.3.4.6 |
ty1250CfgDialTable OBJECT IDENTIFIER .1.3.6.1.4.1.466.3.5 |
ty1250CfgDialButtonIn switched applications, Enables/Disables
the button on front of unit. This button can
used to manual answer an incomming call, or
dial out the default number. The valid values
are enable-button (1) and disable-button (2).rw Enumeration .1.3.6.1.4.1.466.3.5.1 |
ty1250CfgDialDtrIn switched applications, Enables/Disables
dialing on DTR signal transition. Valid values
enable-dtr (1) and disable-dtr (2).rw Enumeration .1.3.6.1.4.1.466.3.5.2 |
ty1250CfgDialRtsDiscIn switched applications, Enables/Disables
disconnecting on RTS signal transition. Valid
values are enable-rts (1) and disable-rts (2).rw Enumeration .1.3.6.1.4.1.466.3.5.3 |
ty1250CfgDialRiIn switched applications, Enables/Disables
incoming call notification to DTE via RI
signal. Valid values are enable-ri (1)
and disable-ri (2).rw Enumeration .1.3.6.1.4.1.466.3.5.4 |
ty1250CfgMaintTableThe Maintenance Port Configuration table contains
parameters for the Maintenance ports on the
1250. The Terminal Port is Index=1; SLIP port is 2 SEQUENCE OF Ty1250CfgMaintEntry .1.3.6.1.4.1.466.3.6 |
ty1250CfgMaintEntryMaintenance Port Configuration Object Ty1250CfgMaintEntry .1.3.6.1.4.1.466.3.6.1 |
ty1250CfgMaintIndexThe Maintenance port under consideration. On the
1250, the Terminal Port is Index=1; SLIP port is 2.ro INTEGER .1.3.6.1.4.1.466.3.6.1.1 |
ty1250CfgMaintModeThe Mode for this Maintenance Port. Values include
ascii-vt100 (4), slip (7), and cslip (8).rw Enumeration .1.3.6.1.4.1.466.3.6.1.2 |
ty1250CfgMaintBaudBaud rate for this Maintenance port. Values are
baud-2400 (2), baud-9600 (4), baud-19200 (5).rw Enumeration .1.3.6.1.4.1.466.3.6.1.3 |
ty1250CfgMaintDataBitsDatabits for this Maintenance port. Values
are databits-7 (1) and databits-8 (2).rw Enumeration .1.3.6.1.4.1.466.3.6.1.4 |
ty1250CfgMaintStopBitsNumber of Stopbits for this Maintenance port.
Values are stopbits-1 (1), stopbits-1-5 (2),
and stopbits-2 (3).rw Enumeration .1.3.6.1.4.1.466.3.6.1.5 |
ty1250CfgMaintParityParity for this Maintenance port. Values are
no-parity (1), odd-parity (2), even-parity (3).rw Enumeration .1.3.6.1.4.1.466.3.6.1.6 |
ty1250CfgMaintFlowCtrlFlow Control for this Maintenance port. Values
are no-flow-control (1), software-flow-control (2),
and hardware-flow-control (3).rw Enumeration .1.3.6.1.4.1.466.3.6.1.7 |
ty1250CfgSlipTable OBJECT IDENTIFIER .1.3.6.1.4.1.466.3.8 |
ty1250CfgSlipMyIPThe IP address for this node.rw IpAddress .1.3.6.1.4.1.466.3.8.1 |
ty1250CfgSlipPeerIPThe IP address for other end of slip connection.rw IpAddress .1.3.6.1.4.1.466.3.8.2 |
ty1250CfgSlipMaskThe IP Network Mask (eg 255.255.255.0) for the
SLIP link.rw IpAddress .1.3.6.1.4.1.466.3.8.3 |
ty1250CfgSlipMaxMTUThe Maximum Transmission Unit is the size of the
largest IP packet supported. This value should
be set to the lowest value supported by any
equipment in the transmission path. A size of
1006 (including header) is suggested.rw INTEGER .1.3.6.1.4.1.466.3.8.4 |
ty1250CallTable OBJECT IDENTIFIER .1.3.6.1.4.1.466.3.9 |
ty1250CallStatusThe call status is shown here.ro Enumeration .1.3.6.1.4.1.466.3.9.1 |
ty1250CallNumberThe last phone number dialed out.rw DisplayString .1.3.6.1.4.1.466.3.9.2 |
ty1250CallUpTimeNumber of seconds the call has been up.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.466.3.9.3 |
ty1250CallStateCall-related actions:
a: Connect (initiate a call),
b: Disconnect (terminate a call)
c: Answer (answer an incoming call).rw Enumeration .1.3.6.1.4.1.466.3.9.4 |
ty1250DiagUnitTable OBJECT IDENTIFIER .1.3.6.1.4.1.466.3.10 |
ty1250DiagUnitLocLoopEnables the operator to control and examine the
UNIT local loopback. This loopback occurs on
all network ports transmit and receive logic.
The unit will transmit DTE data out to the network
as normal, and will also loop DTE data back to
the DTE.rw Enumeration .1.3.6.1.4.1.466.3.10.1 |
ty1250DiagUnitResetEnables the operator to remotely reset the unit.
Using this command will cause the unit to terminate
all its connections and drop data.rw Enumeration .1.3.6.1.4.1.466.3.10.2 |
ty1250DiagNetTable OBJECT IDENTIFIER .1.3.6.1.4.1.466.3.11 |
ty1250DiagNetLineStatusThe Current status of the physical interface.
Your network carrier can send Out-of-Service
or Maintenance Mode codes.ro Enumeration .1.3.6.1.4.1.466.3.11.1 |
ty1250DiagNetLclLpbkEnables the operator to control and examine the
network local loopback. This loopback occurs on
the net side of the local transmit and receive
logic. The unit continues to receive data from
the network and also loops received data back to
the network.rw Enumeration .1.3.6.1.4.1.466.3.11.2 |
ty1250DiagNetRmtLpbkEnables the operator to examine (ONLY) the
status of network loopbacks placed by external
equipment, such as your local CO. These loopbacks
will loop received network data back out the
network, disconnecting the DTE completely.ro Enumeration .1.3.6.1.4.1.466.3.11.3 |
ty1250DiagDteTable OBJECT IDENTIFIER .1.3.6.1.4.1.466.3.12 |
ty1250DiagDteSigRTSThe Dte Channel RTS signal. Values are
rts-signal-on (1) and rts-signal-off (2).ro Enumeration .1.3.6.1.4.1.466.3.12.1 |
ty1250DiagDteSigDTRThe Dte Channel DTR signal.
Values are dtr-signal-on (1) and dtr-signal-off (2).ro Enumeration .1.3.6.1.4.1.466.3.12.2 |
ty1250DiagDteLclLpbkThis selection displays the status or controls the
Local DTE Channel Loopback for the selected channel.
This is will loop DTE data back towards the DTE interface
in addition to passing it on to the network.rw Enumeration .1.3.6.1.4.1.466.3.12.5 |
ty1250DiagDteV54LpbkThis selection displays the status of the DTE Channel
V.54 Loopback for the channel. This loopback is
initiated by the remote node, causing this node to loop
data back to the remote node.ro Enumeration .1.3.6.1.4.1.466.3.12.6 |
ty1250DiagDteBerStateBERT test related actions:
a: Starts a BERT test on a channel,
b: Stops a BERT test on a channel,
c: Inject Errors while the BERT test is running,
d: Clears BERT test errors.rw Enumeration .1.3.6.1.4.1.466.3.12.7 |
ty1250DiagDteBerStatusDisplays the current BERT test sync status.ro Enumeration .1.3.6.1.4.1.466.3.12.8 |
ty1250DiagDteBerErrorsDisplays the number of errors detected in Bert Test.ro Counter .1.3.6.1.4.1.466.3.12.9 |
ty1250DiagDteBerErrSecDisplays the number of seconds containing errors
in BERT Test.ro Counter .1.3.6.1.4.1.466.3.12.10 |
ty1250DiagDteBerTimeElapsElapsed time since BERT test was started or cleared.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.466.3.12.11 |
ty1250DiagDteBerResyncsDisplays the number of times BERT test has synched up
on the pattern.ro Counter .1.3.6.1.4.1.466.3.12.12 |
ty1250DiagDteRmtV54LpbkThis selection controls the DTE Channel V.54 Remote Loopback.
Transmit-code-enable (3) will cause the node to transmit
a V.54 code to the remote node which will then loop
received data back to this node. transmit-code-disable (4)
will transmit the disable code.rw Enumeration .1.3.6.1.4.1.466.3.12.13 |
ty1250AlarmTypeThe type of alarms that are generated on the nodero Enumeration .1.3.6.1.4.1.466.3.13 |
ty1250CfgSnmpTable OBJECT IDENTIFIER .1.3.6.1.4.1.466.3.14 |
ty1250CfgSnmpManagerIPThe IP address for the SNMP manager to receive
this node's TRAPs.rw IpAddress .1.3.6.1.4.1.466.3.14.1 |
ty1250StatsDteTable OBJECT IDENTIFIER .1.3.6.1.4.1.466.3.15 |
ty1250StatsDteTxByteCountThe statistic counting the number of bytes transmitted
on the DTE channel.ro INTEGER .1.3.6.1.4.1.466.3.15.1 |
ty1250StatsDteRxByteCountThe statistic counting the number of bytes received
on the DTE channel.ro INTEGER .1.3.6.1.4.1.466.3.15.2 |
ty1250StatsDteClearStatsAllows the user to zero out all the statistics in
the DTE statistics table.rw Enumeration .1.3.6.1.4.1.466.3.15.3 |
ty1250StatsNetTable OBJECT IDENTIFIER .1.3.6.1.4.1.466.3.16 |
ty1250StatsNetLoopLengthThe statistic that estimates line attentuation
on the network channel.ro INTEGER .1.3.6.1.4.1.466.3.16.1 |
ty1250StatsNetBpvCountThe statistic counting the number of BPV errors
on the network channel.ro INTEGER .1.3.6.1.4.1.466.3.16.2 |
ty1250StatsNetTxByteCountThe statistic counting the number of bytes transmitted
on the network channel.ro INTEGER .1.3.6.1.4.1.466.3.16.3 |
ty1250StatsNetRxByteCountThe statistic counting the number of bytes received
on the network channel.ro INTEGER .1.3.6.1.4.1.466.3.16.4 |
ty1250StatsNetClearStatsAllows the user to zero out all the statistics in
the network statistics table.rw Enumeration .1.3.6.1.4.1.466.3.16.5 |
ty1250CfgTelnetTable OBJECT IDENTIFIER .1.3.6.1.4.1.466.3.17 |
ty1250CfgTelnetEnableEnables/Disables the telnet feature.
Valid values are enable-telnet (1)
and disable-telnet (2).rw Enumeration .1.3.6.1.4.1.466.3.17.1 |
ty1250CfgTelnetAutoLogOutEnables/Disables the telnet auto-logout, logging out
the user after a certain length of idle time.
Valid values are autologout-at-15-minutes (1)
and disable-autologout (2).rw Enumeration .1.3.6.1.4.1.466.3.17.2 |