Home/Catalog/TSDIM-SNMPNE-MIB

TSDIM-SNMPNE-MIB

AI MIB Summary

The TSDIM-SNMPNE-MIB module facilitates the monitoring and management of TSD (Telecom Service Delivery) network elements via SNMP, exposing operational state variables and performance counters specific to the vendor's telecommunications infrastructure. It enables the retrieval of critical NE metrics such as interface status, alarm conditions, and resource utilization data required for fault management and service assurance.

TSD-IM SNMP NE MIB
Main OID:
tsdimSnmpNEMib.1.3.6.1.4.1.637.54.1.1.5
558
Objects
Active
Status
9
Dependencies

Imported Objects

SNMPv2-SMI
SNMPv2-TC
TSDIM-SNMP-TC
TSDIM-SUPPORT-MIB
SNMPv2-CONF
IF-MIB
IANAifType-MIB
OPTICSIM-COMMON-TC
TSDIM-BASICREG-MIB

Objects

558 total
Object Name
tsdimSnmpNEMibTSD-IM SNMP NE MIB
MODULE-IDENTITY
.1.3.6.1.4.1.637.54.1.1.5
tsdimSnmpNEMibObject
OBJECT IDENTIFIER
.1.3.6.1.4.1.637.54.1.1.5.1
tsdimSnmpAgtIpAddressThis scalar object defines the Agent Ip Addressrw
IpAddress
.1.3.6.1.4.1.637.54.1.1.5.1.1
tsdimSnmpAgtUdpPortThis scalar object defines the Agent UDP Port.rw
TsdimUdpPort (TSDIM-SNMP-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.2
tsdimSnmpAgtIpMaskThis scalar object defines the Agent Ip Maskrw
IpAddress
.1.3.6.1.4.1.637.54.1.1.5.1.3
tsdimNeInstallationTypeThis scalar object defines the NE Installation type.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.5
tsdimSdhNeLabelThis object defines the SDH NE user labelrw
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.13
tsdimBoardPositionThis object defines the board position in term of <rrssbb>ro
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.14
tsdimLacTableThe TSDIM Local Access control table. This table is used to give access to the Craft Terminals.
SEQUENCE OF TsdimLacEntry
.1.3.6.1.4.1.637.54.1.1.5.1.17
tsdimLacEntryEntry is automatically created by Agent at start-up time.
TsdimLacEntry
.1.3.6.1.4.1.637.54.1.1.5.1.17.1
tsdimLacStateThis is the State attribute for the Local Access Control. This attribute can be set: - by Agent at creation time to accessRequested - by EML to the values accessGranted or accessDeniedrw
Enumeration
.1.3.6.1.4.1.637.54.1.1.5.1.17.1.1
tsdimLacNoResponseTimeOutPeriodThis is the No Response TimeOut Period attribute for the Local Access \ Control.rw
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.17.1.2
tsdimLacIndexThis is the index for the Local Access Control table.
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.17.1.3
opticsIMNeOwnsByMgrThis scalar object contains the label which identify the manager that is managing the NErw
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.18
opticsIMIfTableThis table contains interface configuration not defined in the IfTable (see inside the IF-MIB).
SEQUENCE OF OpticsIMIfEntry
.1.3.6.1.4.1.637.54.1.1.5.1.19
opticsIMIfEntryAn entry extends IfTable.
OpticsIMIfEntry
.1.3.6.1.4.1.637.54.1.1.5.1.19.1
tsdimIfUnderlieLayerThis object contains the reference to the underlying path layer termination point. This object can be set only when used as physical interface. The default value is <none>.rw
Enumeration
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.1
tsdimIfAsapIndexThis object defines the ASAP object associated to this interface.rw
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.2
tsdimIfOwnsByMgrThis attribute defines the manager which is the owner of the resources involved in this connectionrw
TsdimManagerType (TSDIM-SNMP-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.3
opticsIMIfTxSLThis attribute defines the SL value transmitted in the outgoing direction.ro
SLValue (TSDIM-SNMP-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.4
opticsIMIfExpSLThis attribute defines the SL value expected in the incoming direction.ro
SLValue (TSDIM-SNMP-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.5
opticsIMIfRxSLThis attribute defines the SL value received in the incoming direction.ro
SLValue (TSDIM-SNMP-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.6
opticsIMIfSLSendControlThis attribute defines if the transmitted SL value shall be defined by the agent according to the payload type or it should be the 'equipped-non-specific' code. The value 'automatic' (0) means that the tx SL is calculated by the agent according to the payload type. The value 'forced' (1) means that the tx SL has been forced by the manager to the 'equipped-non-specific' code. This object can be set when the AdminStatus is down or up.rw
Enumeration
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.7
opticsIMIfBridgeBasePortThis attribute value is the bridge port number which lets manager get bridge tables indexed by this number. The default value is equal to zero when no bridge port is created and associated by SNMP agent. When a bridge port can be equipped (its related Ethernet interface is Up, with promiscuous mode and with ETB characterization in case of IEEE 8021.d, 8021.q or also with ETS characterization in case of IEEE 8021.ad), SNMP agent assigns its chosen index to this attributero
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.8
opticsIMIfRateLimitedSpeedThis attribute carries out the rate limiting functionality. ifSpeed value means that the rate limitation of the interface is disabled; this is the default value. The value 0 means that the rate limitation of the interface is disabled; this is the default value. The value can be expressed in bit/s or kbit/s NE dependentrw
Gauge32
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.9
opticsIMIfMeanEgressShapingRateThis attribute carries out the egress shaping rate (sustained rate permitted by egress traffic shaping) in kbit/sec. Disabled rate limitation is the default value.rw
Gauge32
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.10
opticsIMIfBurstEgressShapingSizeThis attribute carries out the burst egress shaping size (amount of traffic in excess of egress shaping rate) in bytes. Default value 0 (null burst egress shaping size)rw
Unsigned32
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.11
opticsIMIfSchedulingDisciplineThis object defines 'on per port basis' scheduling disciplines according to below values: - WorkConserving (1) - NonWorkConserving (2). Default value is WorkConserving(1)rw
INTEGER
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.12
opticsIMIfEntryPortTrafficEnabledopticsIMifEntryPortTrafficEnabled specifies the current transmit/receive state of the interface as a result of explicit management action applied to an interface whose ifAdminStatus is up. The up(1) value indicates the interface is ready to transmit and receive network traffic, the down(2) value indicates the interface has blocked both transmit and receive traffic capabilities. If ifAdminStatus is down, then opticsIMifEntryPortTrafficEnabled takes down(2) value, if ifAdminStatus is changed to up(1) then opticsIMifEntryPortTrafficEnabled changes to up(1)rw
Enumeration
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.13
opticsIMIfAdmittedFloodingRateThis attribute carries out 'on per port basis' ingress admitted flooding rate (the threshold value of admitted bandwidth for NE generated flooding traffic as admitted on this ingress interface) and is specified in kilobits per second (Kbps). This value is requested to trigger discarding of NE generatedflooding traffic on this ingress interface and is minor or equal to that specified in ifSpeed for this interface. Disabled flooding rate limitation is the default valuerw
Gauge32
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.14
opticsIMIfHashInputThis attribute enables to choose out 'on per link aggregation interface basis' ingress parameters for hash function. If the bit is 1 it indicates that the relative hashing key parameter will be used for Link Aggregation hash function otherwise if 0 it will be unused. Default value is: a) for Link Aggregation Interface in promiscous mode: bit 0 (MAC DA) and bit 1 (MAC SA) set to 1 and all other bits set to 0; b) for Link Aggregation in non-promiscous mode: bit 6 (All MPLS Labels) set to 1 and all other bits set to 0. This attribute is significant only for Link Aggregation interfacerw
OpticsIMHashingKeyList
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.15
opticsIMIfDemarcRoleThe Current role of the Port. Ports connected with Customer Network will be called as CustomerInterface(1). Ports connected with Provider Network will be called as NetworkINterface(2). The ports which are internally connected to CPU and FPGA are called as Internal(3). The ports which are connected to internal equipment for data traffic are called as internalTraffic (5). The ports which are connected to internal equipment to provide power are called as internalPower (6). The ports which are connected to external equipment to provide power are called as equipmentPower (7).rw
Enumeration
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.16
opticsIMIfLacpEnableThis parameter enables the usage of LACP protocol over Link Aggregation interface. Default value is True (enabled LACP)rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.17
opticsIMIfVplsPortRoleThe Current role of a Port inside VPLS PE. Ports connected with Customer Network will be called as vpls_uni(1). Ports connected with MPLS Core PW will be called as vpls_nni(4). Spoke ports carrying PVLAN will be called as pvlan_spoke(2). Spoke ports carrying PW will be called as pw_spoke(3). Provider Bridge Network Port will be called as other(5).rw
Enumeration
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.18
opticsIMIfRateLimitedDcnTrafficThis attribute carries out the rate limiting functionality for DCN traffic (control Plane and Management Plane) addressed to CPU. A value equal to interface line-rate means that the rate limitation of DCN traffic is disabled; this is the default value. The value can be expressed in bit/s or kbit/s NE dependentrw
Gauge32
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.19
opticsIMIfDownstreamPortSetPortsThe set of NE ports which are permanently assigned by management to the egress downstream port list (list of egress ports supporting trasmitter shutdown or insertion of GFP CSF frames) in front of failure occurring on this interface. The bit position in the egress downstream port list is coded according to the dot1dBasePort parameter. The default value of this object is a string of zeros of appropriate length, indicating not being a member (egress port without trasmitter shutdown and GFP CSF failure propagation). This attribute is relevant ONLY in case of opticsIMEthETSServiceType equal to other.rw
PortList
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.20
opticsIMIfUpstreamPortSetPortsThe set of NE ports which are permanently assigned by management to the upstream port list, where upstream port list includes those NE ports able to trigger transmitted shut-down consequent action on this interface: operational consequent action on this interface is constrained to combined failure conditions detected (logical AND) over entire upstream port list. The bit position in the ingress upstream port list is coded according to the dot1dBasePort parameter. The default value of this object is a string of zeros of appropriate length, indicating not being a member (ingress port triggering no consequent action). This attribute is relevant ONLY in case of opticsIMEthETSServiceType equal to other.rw
PortList
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.21
opticsIMIfBroadcastTrafficEnableopticsIMifBroadcastTrafficEnable specifies the broadcast traffic transmit capability of an egress interface as a result of explicit management action. True value (Default value) indicates the interface is enabled to transmit broadcast traffic, false value indicates the interface is denied to transmit broadcast traffic.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.22
opticsIMIfUnknownTrafficEnableopticsIMifUnknownTrafficEnable specifies the unknown traffic transmit capability of an egress interface as a result of explicit management action. True value (Default value) indicates the interface is enabled to transmit unknown traffic, false value indicates the interface is denied to transmit unknown traffic.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.23
opticsIMIfPdhRateThis parameter specifies the type of PDH signal carried by the interface.rw
Enumeration
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.24
opticsIMIfOffsetEgressShapingSizeThis attribute carries out the server-layer offset (in bytes) for each specific frame. As a consequence, per-port basis egress shaping rate is decreased by a delta value inferred via per-frame basis server-layer encapsulation header. Default value is indicated as 0xFFFF and is internally set according to the following considerations: - if opticsIMNeFrameSizeMode is equal to layer2 than the default set is equal to 0 (no offset). - if opticsIMNeFrameSizeMode is equal to layer1 than the default set is interface type specificrw
Unsigned32
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.25
opticsIMIfPIPMacAddressThis attribute contains user-provisioned PIP MAC addressrw
PhysAddress (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.26
opticsIMIfMCEnableThis parameter enables the interworking with Media Converter. Default value is False (no interworking with Media Converter)rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.27
opticsIMIfLPTSendControlThis attribute enables or disables the usage of per-port LPT transmit capability. Allowed values: - disabled (0) no consequent LPT frame (IDLE insertion) - gfpcsf (1) via opticsimGFPConfCsf - linkoam (2) 802.3ah This object can be set when the AdminStatus is down or up.rw
INTEGER
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.28
opticsIMIfLPTCsfConsequentActionsThis attribute defines per-port LPT CSF Consequent Actions This object identifies the consequent action triggered on CIF Interface egress port for port-to-port application in front of received LPT Frame indications (due to detected remote CIF Ethernet PHY Interface failures). The choice of enabled LPT CSF consequent actions is allowed to be different from LPT SSF consequent actions (consequent actions coping with network failures). Allowed values: - disabled (0) - default value - is defined to perform no consequent actions. - tx_shutdown(1) is defined to trigger forced transmitter shut-down action - gfp_csf (2) is defined to trigger GFP CSF transmission - linkoam_cle (3) is defined to trigger Link OAM CLE transmission If the interface is not involved in a port-to-port application this consequent action will never be triggered. This object can be set when the AdminStatus is down or up.rw
INTEGER
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.29
opticsIMIfLPTSsfConsequentActionsThis attribute defines per-port LPT SSF Consequent Actions This object identifies the consequent action triggered on CIF Interface egress port for port-to-port application in front of Server Layer failures. The choice of enabled LPT SSF consequent actions is allowed to be different from LPT CSF consequent actions (consequent actions coping with in front of LPT Frame indications). Allowed values: - disabled (0) - default value - is defined to perform no consequent actions. - tx_shutdown(1) is defined to trigger forced transmitter shut-down action - gfp_csf (2) is defined to trigger GFP CSF transmission - linkoam_cle (3) is defined to trigger Link OAM CLE transmission If the interface is not involved in a port-to-port application this consequent action will never be triggered. This object can be set when the AdminStatus is down or up.rw
INTEGER
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.30
opticsIMIfLPTHoldOffTimeThis attribute specifies consequent Actions Hold-Off values in steps di 0.1 sec. Default Value is 0rw
INTEGER
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.31
opticsIMIfBroadcastTrafficLimitThis attribute carries out 'on per port basis' ingress admitted broadcast traffic rate (the threshold value of broadcast traffic rate as admitted on this ingress interface) and is specified in Kilobits per second (Kbps). This value is requested to trigger discarding of NE generated broadcast traffic on this ingress interface and is minor or equal to that specified in ifSpeed for this interface. Disabled broadcast traffic rate limitation is the default value.rw
Gauge32
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.32
opticsIMIfMulticastTrafficLimitThis attribute carries out 'on per port basis' ingress admitted multicast traffic rate (the threshold value of multicast traffic rate as admitted on this ingress interface) and is specified in Kilobits per second (Kbps). This value is requested to trigger discarding of NE generated multicast traffic on this ingress interface and is minor or equal to that specified in ifSpeed for this interface. Disabled multicast traffic rate limitation is the default value.rw
Gauge32
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.33
opticsIMIfUnknownUnicastTrafficLimitThis attribute carries out 'on per port basis' ingress admitted unknown unicast rate (the threshold value of unknown unicast traffic rate as admitted on this ingress interface) and is specified in Kilobits per second (Kbps). This value is requested to trigger discarding of NE generated unknown unicast traffic rate on this ingress interface and is minor or equal to that specified in ifSpeed for this interface. Disabled unknown unicast limitation is the default value.rw
Gauge32
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.34
opticsIMIfAvailableBandwidthThis value indicates the total amount of available bandwidth available on this interface and is specified in kilobits per second (Kbps). This value is calculated as the difference between the amount of bandwidth currently in use and that specified in ifSpeed (converted in Kbps). When this value cannot be measured, this value should contain the nominal bandwidth.ro
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.35
opticsIMIfNetBandwidthThis value indicates the total amount of maximum bandwidth available on this interface and is specified in kilobits per second (Kbps).ro
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.36
opticsIMIfUnknownMulticastTrafficLimitThis attribute carries out 'on per port basis' ingress admitted unknown multicast rate (the threshold value of unknown multicast traffic rate as admitted on this ingress interface) and is specified in Kilobits per second (Kbps). This value is requested to trigger discarding of NE generated unknown mulitcast traffic rate on this ingress interface and is minor or equal to that specified in ifSpeed for this interface. Disabled unknown multicast limitation is the default value.rw
Gauge32
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.37
opticsIMPortCapabilityIndexThis attribute is a pointer to capability profile entries having opticsIMCapabilityProfileProfIndex equal to opticsIMPortCapabilityIndex. The opticsIMCapabilityProfileTable contains information about capabilities supported by this interface. Default value is zero to indicate no capability profile is referenced.rw
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.38
opticsIMIfSwitchIdThis attribute specifies the Ethernet Switch Instance this port belongs to .rw
INTEGER
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.39
opticsIMIfUserLabelA textual string containing an Label provided by operator for this Interface.rw
OpticsIMUserLabel (TSDIM-SNMP-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.40
opticsIMIfPortAlarmAdminopticsIMIfPortAlarmAdmin specifies 'on per port basis' Port Alarm Admin value according to below admitted values: - ne-def: 'on per NE basis' Alarm Admim Value (Default value) - mon: this Port Alarm Admin value takes as effect the ASAP is considered: the alarms emitted by that port are handled according to the pointed ASAP object - auto: this Port Alarm Admin value takes as effect the ASAP (associated to that port) to be ignored: the alarms emitted by that port are inhibited independently on the pointed ASAP object (via tsdimIfAsapIndex).rw
Enumeration
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.41
opticsIMIfIpIntfPointerthe reference pointer of opticsIMVrfIpIntf index. The value 0 means that the interface is not IP. Value 0 is the default valuerw
Unsigned32
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.42
opticsIMIfAlarmReevalThis attribute triggers the interface alarm reevaluation. When this object is set to True the presence of the alarm is reconsidered, starting in any case from a not alarmed status. If the alarm conditions are matched then the alarm is raised, if it was already present the alarm shall be maintained. Default value is False.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.43
opticsIMIflnkaggThresholdNumber of links considered in the detection of the LAG Excessive Bandwidth Degrade (dLAGEXBD) defect: if the number of LAG links, which are both attached from LACP perspective and working (i.e. not in failure condition), is lower than the opticsIMIflnkaggThreshold value and > 0 then the dLAGEXBD is detected. The value of this object is meaningful only in case of LAG ifType. Default value: 1rw
INTEGER
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.44
opticsIMIf1588TCStatusThis object contains the status of the 1588 Transparent Clock management related the this interface's entry. The Transparent Clock is activated on 'NE basis' but each interface could be in a different status. The 'notApplicable' value is returned when the interface doesn't support the management of the 1588 TC. The 'active' value is returned when the interface is supporting the 1588 TC and the feature is actualy working on. The 'notActive' value is returned when the interface is supporting the 1588 TC but the feature is not working due to some temporary conditions.ro
Enumeration
.1.3.6.1.4.1.637.54.1.1.5.1.19.1.45
tsdimAlarmPlmRaiseThis notification reports the Payload Mismatch (PLM) defect.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.20
tsdimAlarmPlmClearThis notification reports the Payload Mismatch (PLM) defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.21
opticsIMSdhIfTableThis table contains the configuration of the server TTP. At startup or when a server TTP is deleted the objects assume the default value.
SEQUENCE OF OpticsIMSdhIfEntry
.1.3.6.1.4.1.637.54.1.1.5.1.22
opticsIMSdhIfEntry
OpticsIMSdhIfEntry
.1.3.6.1.4.1.637.54.1.1.5.1.22.1
opticsIMSdhIfSpeedValue of ifSpeed of the relative server TTP. The value 0 is the default. The change of this object is notified by an Attribute Value Change (AVC) Notification. The value can be expressed in bit/s or kbit/s NE dependent.ro
Gauge32
.1.3.6.1.4.1.637.54.1.1.5.1.22.1.1
opticsIMSdhIfUnderlieLayerType of the relative server TTP (SDH or PDH). The value none is the default. The change of this object is notified by an Attribute Value Change (AVC) Notification.ro
Enumeration
.1.3.6.1.4.1.637.54.1.1.5.1.22.1.2
opticsIMSdhIfTypeType of the interface associated with the server TTP. The value other (1) is the default and applies when no interface type is associated with the server TTP. The change of this object is notified by an Attribute Value Change Notification.ro
IANAifType (IANAifType-MIB)
.1.3.6.1.4.1.637.54.1.1.5.1.22.1.3
opticsIMSdhIfVcTypeType of the underlying SDH VC. The value other (1) is the default and applies to the case where the underlying layer is not SDH/SONET/PDH or PCONC. The other values (vc12,vc3,vc4,vc4-4c) apply only when the underlying layer is SDH or PCONC. The values (vt1-5, sts-1, sts-3c, sts-12c, sts-192c, vt-2, vt-3, vt-6 ) are applicable when the underlying layer is SONET or PCONC. The values (pdh-e1, pdh-ds1, pdh-e3, pdh-ds3 ) are applicable are applicable when the underlying layer is PDH or PCONC. The change of this object is notified by an Attribute Value Change Notification.ro
Enumeration
.1.3.6.1.4.1.637.54.1.1.5.1.22.1.4
opticsIMSdhIfCurrSpeedValue of actual ifSpeed of the relative server TTP. The value of the opticsIMSdhIfSpeed is the default. When the underlying layer is PCONC or VCONC it represents the number of active and working VCs in the virtual or packet concatenated Group and therefore it could be lower than the opticsIMSdhIfSpeed. The change of this object is notified by an Attribute Value Change (AVC) Notification. The value can be expressed in bit/s or kbit/s NE dependentro
Gauge32
.1.3.6.1.4.1.637.54.1.1.5.1.22.1.5
tsdimAlarmTsfRaiseThis notification reports TSF alarm.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.23
tsdimAlarmTsfClearThis notification reports TSF alarm clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.24
tsdimInfoModelVersionMajorThis is the infomodel major version value.ro
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.25
tsdimInfoModelVersionMinorThis is the infomodel minor version valuero
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.26
tsdimInfoModelVersionMaintenanceThis is the infomodel maintenance version valuero
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.27
opticsIMNeConfiguration
OBJECT IDENTIFIER
.1.3.6.1.4.1.637.54.1.1.5.1.28
opticsIMNeConfigurationTypeThis object defines the NE configuration type requested by the managing system.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.28.1
opticsIMNeConfigurationTypeIdThis object defines the identifier of the NE configuration type requested by the managing system. This identifier must be included in one of the entries of the opticsIMAllowedNeConfigurationTypeTable. As a side effect of setting this object, the agent must set the opticsIMNeConfigurationType object with the string associated to this identifier.rw
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.28.2
opticsIMAllowedNeConfigurationTypeTableThis table contains all the configurations types allowed for the supported NE.
SEQUENCE OF OpticsIMAllowedNeConfigurationTypeEntry
.1.3.6.1.4.1.637.54.1.1.5.1.28.3
opticsIMAllowedNeConfigurationTypeEntryAn entry of the allowed Ne configuration types table. Each entry (row) corresponds to a configuration type allowed for the NE.
OpticsIMAllowedNeConfigurationTypeEntry
.1.3.6.1.4.1.637.54.1.1.5.1.28.3.1
opticsIMAllowedNeConfigurationIdThis object contains the identifier associated to a NE configuration type. It identifies the index of the table.
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.28.3.1.1
opticsIMAllowedNeConfigurationTypeThis object identifies an allowed configuration type of the NE.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.28.3.1.2
opticsIMMarketThis object specifies the application market. With this information the agent will be able to provide to the manager only the configurations consistent with the market defined.rw
Enumeration
.1.3.6.1.4.1.637.54.1.1.5.1.28.4
opticsIMNeEquipmentNameThis scalar object defines in synthesis the NE characteristics (NE name, frequency, configuration type, modulation,capability...)ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.28.5
opticsIMAllowedNePeripheralTableThis table contains all the peripherals (type and configuration) allowed for each configuration Ne allowed on the NE.
SEQUENCE OF OpticsIMAllowedNePeripheralEntry
.1.3.6.1.4.1.637.54.1.1.5.1.28.6
opticsIMAllowedNePeripheralEntryAn entry of the allowed NE peripherals table. Each entry (row) corresponds to an allowed peripheral type and peripheral configuration for each configuration type Ne allowed for the NE
OpticsIMAllowedNePeripheralEntry
.1.3.6.1.4.1.637.54.1.1.5.1.28.6.1
opticsIMAllowedNePeripheralIdThis object contains the identifier associated to a peripheral type and peripheral configuration. It identifies the index of the table.
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.28.6.1.1
opticsIMAllowedNePeripheralTypeThis object identifies an allowed peripheral type.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.28.6.1.2
opticsIMAllowedNePeripheralConfigurationThis object identifies an allowed configuration type of the peripheral.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.28.6.1.3
opticsIMNeTrsDirectionTableThis table contains the parameters associated to the transmission directions on NE. A transmission direction connects the NE to an adjacent NE by a specific transmission interface (i.e. radio, PDH)
SEQUENCE OF OpticsIMNeTrsDirectionEntry
.1.3.6.1.4.1.637.54.1.1.5.1.28.7
opticsIMNeTrsDirectionEntryAn entry of the direction table. Each entry (row) corresponds to a specific direction.
OpticsIMNeTrsDirectionEntry
.1.3.6.1.4.1.637.54.1.1.5.1.28.7.1
opticsIMNeTrsDirectionIndexThis object contains the identifier associated to a transmission direction to/from an adjacent NE. It identifies the index of the table.
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.28.7.1.1
opticsIMNeTrsDirectionConfigurationIdThis object defines the identifier of the NE configuration type requested by the managing system on this direction. Thid identifier must be included in one of the entries of the opticsIMAllowedNeConfigurationTypeTable.rw
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.28.7.1.2
opticsIMNeTrsDirectionMaxCapacityThis object contains the maximum transmission capacity on this direction. It is updated by managed system (agent) after configuration of transmission capacity for each interface (i.e. radio, PDH on each specific object) belonging to this direction.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.28.7.1.3
opticsIMNeTrsDirectionRoleThis object reports a specific behaviour for this direction. It is used to differ the behaviour of this direction from the behaviour of the other directions. The content is defined in each product specification.rw
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.28.7.1.4
opticsIMNeTrsDirectionRowStatusSee textual convention.rw
RowStatus (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.28.7.1.5
opticsIMNeDirectionPeripheralTableThis table contains all the peripheral (type and configuration) selected for each direction on the NE.
SEQUENCE OF OpticsIMNeDirectionPeripheralEntry
.1.3.6.1.4.1.637.54.1.1.5.1.28.8
opticsIMNeDirectionPeripheralEntryAn entry of direction table. Each entry (row) corresponds to a selected peripheralId for each direction
OpticsIMNeDirectionPeripheralEntry
.1.3.6.1.4.1.637.54.1.1.5.1.28.8.1
opticsIMNeDirectionPeripheralIndexThis object contains the index of a peripheral identifier selected on a direction. It identifies the index of the table.
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.28.8.1.1
opticsIMNeDirectionPeripheralIdThis object defines the identifier of the peripheral type and peripheral configuration requested by the managing systems. This identifier must be included in one of the opticsIMAllowedNePeripheralTable associated to the opticsIMNeTrsDirectionConfigurationId object on opticsIMNeTrsDirectionTable. As a side effect of setting this object, the agent must set the opticsIMNeDirectionPeripheralType object and the opticsIMNeDirectionPeripheralConfiguration object with the strings associated.rw
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.28.8.1.2
opticsIMNeDirectionPeripheralTypeThis object defines a pheripheral type requested by the managing system on a direction.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.28.8.1.3
opticsIMNeDirectionPeripheralConfigurationThis object defines a pheripheral configuration requested by the managing system on a direction.rw
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.28.8.1.4
opticsIMNeDirectionPeripheralRowStatusSee textual convention.rw
RowStatus (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.28.8.1.5
opticsIMNeCompositionTableThis table contains the composition of the NE in term of NE configuration type requested by the managing system.
SEQUENCE OF OpticsIMNeCompositionEntry
.1.3.6.1.4.1.637.54.1.1.5.1.28.9
opticsIMNeCompositionEntryAn entry of the NE composition table. Each entry (row) corresponds to a configuration type allowed for the NE.
OpticsIMNeCompositionEntry
.1.3.6.1.4.1.637.54.1.1.5.1.28.9.1
opticsIMNeCompositionIndexThis object contains the index of the table.
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.28.9.1.1
opticsIMNeCompositionConfigurationIdThis object defines a identifier of the NE configuration type requested by the managing system. This identifier must be included in one of the entries of the opticsIMAllowedNEConfigurationTypeTable. As a side effect of this setting, the agent must set the opticsIMNeCompositionConfigurationType object with the string associated to this identifier.rw
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.28.9.1.2
opticsIMNeCompositionConfigurationTypeThis object defines a NE configuration type requested by the managing system.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.28.9.1.3
opticsIMNeCompositionRowStatusSee textual convention.rw
RowStatus (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.28.9.1.4
opticsIMNeCompositionIndexNextThis object contains an appropriate value to be used for opticsIMNeCompositionIndex when creating entries in the opticsIMNeCompositionTable. The value 0 indicates that no unassigned entries are available. To obtain the opticsIMNeCompositionIndex value for a new entry, the manager issues a management protocol retrieval operation to obtain the current value of this object. After each retrieval, the agent should modify the value to the next unassigned index. After a manager retrieves a value, the agent will determine through its local policy when this index value will be made available for reuse.ro
Unsigned32
.1.3.6.1.4.1.637.54.1.1.5.1.28.10
opticsIMProtectionIndexNextThis object contains an appropriate value to be used for opticsIMProtectionConfigurationIndex when creating entries in the opticsIMProtectionConfigurationTable. The value 0 indicates that no unassigned entries are available. To obtain the opticsIMProtectionConfigurationIndex value for a new entry, the manager issues a management protocol retrieval operation to obtain the current value of this object. After each retrieval, the agent should modify the value to the next unassigned index. After a manager retrieves a value, the agent will determine through its local policy when this index value will be made available for reuse.ro
Unsigned32
.1.3.6.1.4.1.637.54.1.1.5.1.28.11
opticsIMProtectionConfigurationTableThis table allows the managing system to define the protection type on equipment provisioning in order to create the protection schemes. It is indexed by the equipment position, related to equipmentTable, involved in the protection scheme
SEQUENCE OF OpticsIMProtectionConfigurationEntry
.1.3.6.1.4.1.637.54.1.1.5.1.28.12
opticsIMProtectionConfigurationEntryAn entry of the protection configuration table. Each entry (row) corresponds to a Protection type involving 2 equipment position on equipmentTable.
OpticsIMProtectionConfigurationEntry
.1.3.6.1.4.1.637.54.1.1.5.1.28.12.1
opticsIMProtectionConfigurationIndexThis object contains the index of the table. It contains the value retrieved from agent by a GET request on opticsIMProtectionIndexNext object.
Unsigned32
.1.3.6.1.4.1.637.54.1.1.5.1.28.12.1.1
opticsIMProtectionEqptPositionMainThis object contains the index of the table. It contains the same value of equipmentPosition index on OpticsIMEquipmentEntry that the managing system requires involved in a protection scheme.rw
OCTET STRING
.1.3.6.1.4.1.637.54.1.1.5.1.28.12.1.2
opticsIMProtectionEqptPositionSpareThis object contains the index of the table. It contains the same value of equipmentPosition index on OpticsIMEquipmentEntry that the managing system requires involved in a protection scheme.rw
OCTET STRING
.1.3.6.1.4.1.637.54.1.1.5.1.28.12.1.3
opticsIMProtectionTypeThis object defines the protection for the equipment related to this postion.rw
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.28.12.1.4
opticsIMProtectionRowStatusSee textual convention.rw
RowStatus (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.28.12.1.5
opticsIMProtectionTypeIdThis object contains the identifier of the protection type related to opticsIMProtectionEqptPositionMain and opticsIMProtectionEqptPositionSpare requested by the managing systems. The identifier must be included in one of the entries of the opticsIMAllowedProtectionTypesTable associated to the equipmentExpected for the opticsIMProtectionEqptPositionMain and opticsIMProtectionEqptPositionSpare. As a side effect of setting this object, the agent must set the opticsIMProtectionType object with the string associated to this identifier (see opticsIMAllowedprotectionTypesTable).rw
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.28.12.1.6
opticsIMAllowedProtectionTypesTableThis table contains, for each equipment type allowed in the NE, the allowed protection types.
SEQUENCE OF OpticsIMAllowedProtectionTypesEntry
.1.3.6.1.4.1.637.54.1.1.5.1.28.13
opticsIMAllowedProtectionTypesEntryAn entry of the allowed protection type table. Each entry (row) corresponds to an protection type allowed for the equipment type identified by the equipmentType object.
OpticsIMAllowedProtectionTypesEntry
.1.3.6.1.4.1.637.54.1.1.5.1.28.13.1
equipmentTypeThis object contains an equipment type allowed on the NE.
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.28.13.1.1
allowedProtectionTypeIdThis object contains the identifier of an protection type allowed for the associated equipment type.
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.28.13.1.2
allowedProtectionTypeThis object identifies the protection type (string) associated to the allowedProtectionTypeId.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.28.13.1.3
opticsIMTopologyGroupThis object identifies the group that the NE belong to. A Service could be created on NEs belonging to the same group.rw
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.28.14
opticsIMExternalTimeThis object specifies the current time of the NE. This time has to be used as reference for all time stamp activities in the NE.rw
DateAndTime (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.29
opticsIMNTPManagement
OBJECT IDENTIFIER
.1.3.6.1.4.1.637.54.1.1.5.1.30
opticsIMNTPStatusThis object is used to enable/disable the Network Time Protocol (NTP).rw
Enumeration
.1.3.6.1.4.1.637.54.1.1.5.1.30.1
opticsIMMainNTPServerAddressThis object contains the address of the main server of the Network Time Protocol (NTP).rw
IpAddress
.1.3.6.1.4.1.637.54.1.1.5.1.30.2
opticsIMSpareNTPServerAddressThis object contains the address of the spare server of the Network Time Protocol (NTP).rw
IpAddress
.1.3.6.1.4.1.637.54.1.1.5.1.30.3
opticsIMNTPServersReachabilityStatusThis object is used to indicate if the Network Time Protocol (NTP) servers (main and spare) are reachable.ro
Enumeration
.1.3.6.1.4.1.637.54.1.1.5.1.30.4
opticsIMMainNTPServerIPv6AddressThis object contains the address of the main server of the Network Time Protocol (NTP) in the IPv6 format.rw
InetAddressIPv6 (TSDIM-SUPPORT-MIB)
.1.3.6.1.4.1.637.54.1.1.5.1.30.62
opticsIMSpareNTPServerIPv6AddressThis object contains the address of the spare server of the Network Time Protocol (NTP) in the IPv6 format.rw
InetAddressIPv6 (TSDIM-SUPPORT-MIB)
.1.3.6.1.4.1.637.54.1.1.5.1.30.63
opticsimEpsConfStatusThis object reports information about the EPS (Equipment Protection Switching) configuration of an ISA board. If the ISA board does not support plug-able access card, this object becomes true if and only if the ISA board is EPS protected. If the ISA board supports plug-able access card, this object becomes true if and only if the ISA board is EPS protected and both the main and the spare boards are equipped with the same access card.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.31
opticsimEpsActiveRoleThis object report the role (i.e. main or spare) of the active ISA board. This object is meaningful only if the opticsimEpsConfStatus is true. Otherwise, the value main (1) is always returned.ro
Enumeration
.1.3.6.1.4.1.637.54.1.1.5.1.32
opticsimIsaAccessThis object report the access card equipped in the Equipment domain for the ISA board. The value 0 (unknown) is the default value for the following cases: - the ISA board does not support equipped access card (e.g. because it is plugged in an old equipment) - the access card in is not known by the ISA board (e.g. it is not a 14xFE nor a 4xGE) The value 1 (none) is used to report that no access card has been equipped. The other values (>1) represent the access card that was equipped. The association between the value of this object and the access card is product specific and will be documented in the product external specificationro
Unsigned32
.1.3.6.1.4.1.637.54.1.1.5.1.33
opticsimMaskNamingRuleThe value of this object provides the mask of the naming of the TTPs. The mask indicates the binary format of the naming composed by the following fields: x for data purposes field, r for rack field, s for subrack field, b for board field, d for drawer field, p for port field, c for channel field. The mask allows the decoding of the naming, specifying for each field (all the fields are present and in the above listed order) the number of reserved bits followed by the character (above provided) that identifies the field itself. In case a field is never used inside the NE, the field is anyway present with number of reserved bits 0 (e.g. if the drawer is never used an example of mask is 4x3r3s10b0d10p2c).ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.34
opticsimSwPackageProfileThis object is used for reporting the software package profile which indicates the network functionalities enabled on the NE. The value of this attribute is commonly agreed, its semantic will be described in the relevant Ext. Interface Management Specification.ro
Bits
.1.3.6.1.4.1.637.54.1.1.5.1.35
opticsimNeAutoProvisioningThis object allows the manager to set the way of physical item provisioning on the NE. The Full Plug&Play value will set the automatic provisioning without manager intervention. The No Plug&Play value will set the provisioning full in the hands of manager. The Confirmed Plug&Play value (that is the default value) will cause the agent to ask for manager confirmation before provisioning. The confirmation request to operator by manager (in the confirmed plug and play case), is activated by an Attribute Value Change (AVC) associated to the change of the opticsEquipmentActual object value in the OPTICSIM-EQPT-MIBrw
Enumeration
.1.3.6.1.4.1.637.54.1.1.5.1.36
opticsIMNePMCollection
OBJECT IDENTIFIER
.1.3.6.1.4.1.637.54.1.1.5.1.37
opticsIMNePMCollectionStatusThis object defines the PM collection NE status: three operating status have been defined: the <Ready_for_Request> status, the <In_Preparation> status, the <fileTransferCompleted> status; the default status is the <fileTransferCompleted> one.ro
Enumeration
.1.3.6.1.4.1.637.54.1.1.5.1.37.1
opticsIMNePMActivateCollectionThis object defines the start of the PM collection on the NE: the value <NormalStart> can be set by manager when he want to activate the PM collection in normal condition; the value <ForcedStart> can be set by manager when he want to activate the PM collection in abnormal condition (for instance when NE is still preparing a previous commanded PM collection); the agent will reset the value to <Noop> when the manager setting has been recognized. The default value is the <Noop> one.rw
Enumeration
.1.3.6.1.4.1.637.54.1.1.5.1.37.2
opticsIMNePMTimePeriodCollectionThis object defines the time value before which no hystorical data must be considered for the PM collection file. The default value, that is the null value (i.e. 0), represents the maximum allowed for that application.rw
OpticsIMPmPeriodTime (OPTICSIM-COMMON-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.37.3
opticsIMMibConfigurationModeThis attribute defines the possibility to 'isolate' (offline) the MIB configuration from the HW Configuration inside the NE. This means both that, at the management interface, requests are not propagated to the HW and alarms are not reported. Default value (online) can be changed only in case of MIB Restore procedure.rw
OpticsIMMibConfigurationMode
.1.3.6.1.4.1.637.54.1.1.5.1.38
opticsIMMngInterfaceListTableThis table defines the list of management Interfaces with: management interface type, address and its charaterization. The address allows reaching the NE applications (Agents) in charge of the specific management interface. In case of SNMP Agent, where for the address an ASN.1 Octect String is simply defined, this string, aligned to SNMPv2-SMI, has to be composed as follows: IpAddress:PortNumber. In case of Q3 Agent, a presentation address consists of octect strings with: - presentation selector, session selector, transport selector and a set of network addresses as defined in RFC 1278. The characterization defines the primary and secondary management interfaces. Primary is the management interface where basic functionalities, like Equipment, LAC, NTP, File Transfer, etc. are accessible.
SEQUENCE OF OpticsIMMngInterfaceListEntry
.1.3.6.1.4.1.637.54.1.1.5.1.39
opticsIMMngInterfaceListEntrysee description of opticsIMMngInterfaceListTable
OpticsIMMngInterfaceListEntry
.1.3.6.1.4.1.637.54.1.1.5.1.39.1
opticsIMMngInterfaceListIndexIndex of opticsIMMngInterfaceListEntry
INTEGER
.1.3.6.1.4.1.637.54.1.1.5.1.39.1.1
opticsIMMngInterfaceTypeIt defines the type of the management interface.ro
OpticsIMMngInterfaceType
.1.3.6.1.4.1.637.54.1.1.5.1.39.1.2
opticsIMMngInterfaceCharacterizationThe characterization defines the primary and secondary management interfaces. Primary is the management interface where basic functionalities, like Equipment, LAC, NTP, File Transfer, etc. are accessible.ro
OpticsIMMngInterfaceCharacterization
.1.3.6.1.4.1.637.54.1.1.5.1.39.1.3
opticsIMMngInterfaceAddressTypeIt defines the address type of the management interface.ro
OpticsIMMngInterfaceAddressType
.1.3.6.1.4.1.637.54.1.1.5.1.39.1.4
opticsIMMngInterfaceAddressIt defines the address associated to the management interface. In case of Ip Address DisplayString is encoded aligned to SNMPv2-SMI, in case of Presentation Address DisplayString is encoded aligned to RFC 1278.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.39.1.5
opticsIMMngInterfaceAdminStateIt defines the administrative state of the management interface. When this object is set to 'disable' value then the NE is not allowed to be supervised from this management interface.rw
Enumeration
.1.3.6.1.4.1.637.54.1.1.5.1.39.1.6
opticsIMCommonAlarms
OBJECT IDENTIFIER
.1.3.6.1.4.1.637.54.1.1.5.1.40
opticsIMAlarmLossOfSignalRaiseThis notification reports the Loss Of Signal (LOS) defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.1
opticsIMAlarmLossOfSignalClearThis notification reports the Loss Of Signal (LOS) defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.2
opticsIMAlarmLossOfFrameRaiseThis notification reports the Loss Of Frame (LOF) defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.3
opticsIMAlarmLossOfFrameClearThis notification reports the Loss Of Frame (LOF) defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.4
opticsIMAlarmAisRaiseThis notification reports the AIS defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.5
opticsIMAlarmAisClearThis notification reports the AIS defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.6
opticsIMAlarmTransmitterFailureRaiseThis notification reports the Transmitter Failure (TF) defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.7
opticsIMAlarmTransmitterFailureClearThis notification reports the Transmitter Failure (TF) defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.8
opticsIMAlarmTransmitterDegradedRaiseThis notification reports the Transmitter Degraded (TD) defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.9
opticsIMAlarmTransmitterDegradedClearThis notification reports the Transmitter Degraded (TD) defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.10
opticsIMAlarmRemoteDefectIndicationRaiseThis notification reports the Remote Defect Indication (RDI) defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.11
opticsIMAlarmRemoteDefectIndicationClearThis notification reports the Remote Defect Indication (RDI) defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.12
opticsIMAlarmCableLOSRaiseThis notification reports the Cable LOS defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.13
opticsIMAlarmCableLOSClearThis notification reports the Cable LOS defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.14
opticsIMAlarmRxLOSRaiseThis notification reports the rxLOS (LOS of the incoming signal for the Rx subfunction) defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.15
opticsIMAlarmRxLOSClearThis notification reports the rxLOS (LOS of the incoming signal for the Rx subfunction) defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.16
opticsIMAlarmRxFailRaiseThis notification reports the rxFail (a fail of the Rx subfunction) defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.17
opticsIMAlarmRxFailClearThis notification reports the rxFail (a fail of the Rx subfunction) defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.18
opticsIMAlarmDemLOSRaiseThis notification reports the demLOS (LOS of the incoming signal for the demodulation subfunction) defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.19
opticsIMAlarmDemLOSClearThis notification reports the demLOS (LOS of the incoming signal for the demodulation subfunction) defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.20
opticsIMAlarmDemFailRaiseThis notification reports the demFail (a fail of the demodulation subfunction) defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.21
opticsIMAlarmDemFailClearThis notification reports the DemFail (a fail of the demodulation subfunction) defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.22
opticsIMAlarmModLOSRaiseThis notification reports the modLOS (LOS of the incoming signal for the modulation subfunction) defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.23
opticsIMAlarmModLOSClearThis notification reports the modLOS (LOS of the incoming signal for the modulation subfunction) defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.24
opticsIMAlarmModFailRaiseThis notification reports the modFail (a fail of the modulation subfunction) defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.25
opticsIMAlarmModFailClearThis notification reports the modFail (a fail of the modulation subfunction) defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.26
opticsIMAlarmTxLOSRaiseThis notification reports the txLOS (LOS of the incoming signal for the Tx subfunction) defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.27
opticsIMAlarmTxLOSClearThis notification reports the txLOS (LOS of the incoming signal for the Tx subfunction) defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.28
opticsIMAlarmTxFailRaiseThis notification reports the txFail (a fail of the Tx subfunction) defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.29
opticsIMAlarmTxFailClearThis notification reports the txFail (a fail of the Tx subfunction) defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.30
opticsIMAlarmTCARaiseThis notification reports the Threshold Crossing Alarm defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.31
opticsIMAlarmTCAClearThis notification reports the Threshold Crossing Alarm defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.32
opticsIMAlarmUnavailableTimeRaiseThis notification reports the Unavailable Time defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.33
opticsIMAlarmUnavailableTimeClearThis notification reports the Unavailable Time defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.34
opticsIMAlarmTsfRaiseThis notification reports the Trail Signal Fail TSF) alarm. It does not apply to ATM interfaces where the tsdimAlarmTsfRaise notification is used.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.35
opticsIMAlarmTsfClearThis notification reports the Trail Signal Fail (TSF) alarm clear. It does not apply to ATM interfaces where the tsdimAlarmTsfClear notification is used.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.36
opticsIMAlarmPlmRaiseThis notification reports the Payload Mismatch (PLM) alarm. It does not apply to ATM interfaces where the tsdimAlarmPlmRaise notification is used.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.37
opticsIMAlarmPlmClearThis notification reports the Payload Mismatch (PLM) alarm clear. It does not apply to ATM interfaces where the tsdimAlarmPlmClear notification is used.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.38
opticsIMAlarmUruRaiseThis notification reports the Underline Resource Unavailable (URU) defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.39
opticsIMAlarmUruClearThis notification reports the Underline Resource Unavailable (URU) defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.40
opticsIMAlarmLAPDFailRaiseThis notification reports the LAPD Fail defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.41
opticsIMAlarmLAPDFailClearThis notification reports the LAPD Fail defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.42
opticsimGfpAlarmGtmRaiseThis notification reports the GFP Type Mismatch (GTM) alarm.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.43
opticsimGfpAlarmGtmClearThis notification reports the GFP Type Mismatch (GTM) alarm clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.44
opticsimDAAlarmDACMRaiseThis notification reports the Loss of DACM alarm.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.45
opticsimDAAlarmDACMClearThis notification reports the Loss of DACM alarm clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.46
opticsIMAlarmLossOfAlignmentRaiseThis notification reports the Loss of Alignment defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.47
opticsIMAlarmLossOfAlignmentClearThis notification reports the Loss of Alignment defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.48
opticsIMAlarmPPPFailRaiseThis notification reports the Point to Point IP Fail defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.49
opticsIMAlarmPPPFailClearThis notification reports the Point to Point IP Fail defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.50
opticsIMAlarmRemoteNEFailureRaiseThis notification reports the Remote NE Failure defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.51
opticsIMAlarmRemoteNEFailureClearThis notification reports the Remote NE Failure defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.52
opticsimSdhConcDegradeRaiseThis notification reports that at least one active VC in a virtual or packet concatenated group is not working and therefore the opticsIMSdhIfCurrSpeed is lower than the nominal opticsIMSdhIfSpeed.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.53
opticsimSdhConcDegradeClearThis notification reports the all the active VCs in a virtual or packet concatenated group are working.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.54
opticsimClientSignalFailRaiseClient Signal Fail raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.55
opticsimClientSignalFailClearClient Signal Fail clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.56
opticsIMAlarmLossOfPointerRaiseThis notification reports the Loss of Pointer defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.57
opticsIMAlarmLossOfPointerClearThis notification reports the Loss of Pointer defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.58
opticsIMAlarmLossOfMultiframeRaiseThis notification reports the Loss of Multiframe defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.59
opticsIMAlarmLossOfMultiframeClearThis notification reports the Loss of Multiframe defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.60
opticsIMAlarmSequenceMismatchRaiseThis notification reports the Sequence mismatch defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.61
opticsIMAlarmSequenceMismatchClearThis notification reports the Sequence mismatch defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.62
opticsIMAlarmServerSignalFailRaiseThis notification reports the Server Signal Fail raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.63
opticsIMAlarmServerSignalFailClearThis notification reports the Server Signal Fail clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.64
opticsIMAlarmUnequippedRaiseThis notification reports the VC-n unequipped defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.65
opticsIMAlarmUnequippedClearThis notification reports the VC-n unequipped defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.66
opticsIMAlarmExstensionHeaderMismatchRaiseThis notification reports the Exstension Header Mismatch (EXM) defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.67
opticsIMAlarmExstensionHeaderMismatchClearThis notification reports the Exstension Header Mismatch (EXM) defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.68
opticsIMAlarmUserPayloadMismatchRaiseThis notification reports the User Payload Mismatch (UPM) defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.69
opticsIMAlarmUserPayloadMismatchClearThis notification reports the User Payload Mismatch (UPM) defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.70
opticsIMAlarmDegradeRaiseThis notification reports Degraded defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.71
opticsIMAlarmDegradeClearThis notification reports Degraded defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.72
opticsimAlarmInputPowerDegradeRaiseThis notification reports input power Degraded defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.73
opticsimAlarmInputPowerDegradeClearThis notification reports input power Degraded defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.74
opticsimAlarmMisconnectionRaiseThis notification reports Misconnection of CESoETH frames defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.75
opticsimAlarmMisconnectionClearThis notification reports Misconnection of CESoETH frames defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.76
opticsimAlarmLateFramesRaiseThis notification reports Late arriving CESoETH Frames defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.77
opticsimAlarmLateFramesClearThis notification reports Late arriving CESoETH Frames defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.78
opticsimAlarmMalformedFramesRaiseThis notification reports Malformed Frames defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.79
opticsimAlarmMalformedFramesClearThis notification reports Malformed Frames defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.80
opticsimAlarmJitterBufferOverrunRaiseThis notification reports the Jitter Buffer Overrun defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.81
opticsimAlarmJitterBufferOverrunClearThis notification reports the Jitter Buffer Overrun defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.82
opticsimAlarmJitterBufferUnderrunRaiseThis notification reports the Jitter Buffer Underrun defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.83
opticsimAlarmJitterBufferUnderrunClearThis notification reports the Jitter Buffer Underrun defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.84
opticsimAlarmServerSignalIngrFailRaiseThis notification reports the Server Signal Fail on ingressing raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.85
opticsimAlarmServerSignalIngrFailClearThis notification reports the Server Signal Fail on ingressing clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.86
opticsimAlarmServerSignalEgreFailRaiseThis notification reports the Server Signal Fail on egressing raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.87
opticsimAlarmServerSignalEgreFailClearThis notification reports the Server Signal Fail on egressing clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.88
opticsimAlarmTrafficDisableRaiseThis notification reports the Traffic Disable raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.89
opticsimAlarmTrafficDisableClearThis notification reports the Traffic disable clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.90
opticsimAlarmEthOAMLossOfContinuityRaiseThis notification reports (Ethernet OAM Continuity Check) Loss Of Continuity raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.91
opticsimAlarmEthOAMLossOfContinuityClearThis notification reports (Ethernet OAM Continuity Check) Loss Of Continuity clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.92
opticsimAlarmEthOAMMisMergeConditionRaiseThis notification reports (Ethernet OAM Continuity Check) MisMerge Condition raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.93
opticsimAlarmEthOAMMisMergeConditionClearThis notification reports (Ethernet OAM Continuity Check) MisMerge Condition clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.94
opticsimAlarmEthOAMUnexpectedMepIdRaiseThis notification reports (Ethernet OAM Continuity Check) UnexpectedMepId raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.95
opticsimAlarmEthOAMUnexpectedMepIdClearThis notification reports (Ethernet OAM Continuity Check) UnexpectedMepId Clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.96
opticsimAlarmEthOAMUnexpectedPeriodRaiseThis notification reports (Ethernet OAM Continuity Check) Unexpected Period raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.97
opticsimAlarmEthOAMUnexpectedPeriodClearThis notification reports (Ethernet OAM Continuity Check) Unexpected Period Clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.98
opticsimAlarmEthOAMUnexpectedLevelRaiseThis notification reports (Ethernet OAM Continuity Check) Unexpected Level raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.99
opticsimAlarmEthOAMUnexpectedLevelClearThis notification reports (Ethernet OAM Continuity Check) Unexpected Level clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.100
opticsimAlarmEthOAMRDIRaiseThis notification reports (Ethernet OAM Continuity Check) Remote Defect Indication raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.101
opticsimAlarmEthOAMRDIClearThis notification reports (Ethernet OAM Continuity Check) Remote Defect Indication clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.102
opticsimAlarmSynchronizationSignalFailRaiseThis notification reports the synchronization signal fail raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.103
opticsimAlarmSynchronizationSignalFailClearThis notification reports the synchronization signal fail clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.104
opticsIMMemoryCardForbiddenToUseRaiseThis notification reports the Memory card forbidden to use alarm raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.105
opticsIMMemoryCardForbiddenToUseClearThis notification reports the Memory card forbidden to use alarm clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.106
opticsIMAlarmLinkOdncRaiseThis notification reports the unsuccessful completion of Link OAM Discovery protocol.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.107
opticsIMAlarmLinkOdncClearThis notification reports the ODNC defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.108
opticsIMAlarmLinkCleRaiseThis notification reports that at least one Critical Link Event flag is present in the received OAMPDUs.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.109
opticsIMAlarmLinkCleClearThis notification reports the CL Event defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.110
opticsIMAlarmLinkSiRaiseThis notification reports an inconsistency of states between the two peer DTEs
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.111
opticsIMAlarmLinkSiClearThis notification reports the SI defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.112
opticsimAlarmEthOAMUNPrRaiseThis notification reports 'A MEP receives a CCM frame with an invalid Priority, but a valid MEG and MEP values' raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.113
opticsimAlarmEthOAMUNPrClearThis notification reports 'A MEP receives a CCM frame with an invalid Priority, but a valid MEG and MEP values' clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.114
opticsimAlarmClockFailureRaiseThis notification reports the failure of the clock raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.115
opticsimAlarmClockFailureClearThis notification reports the the failure of the clock clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.116
opticsimAlarmEthSignalDegradedRaiseThis notification reports the signal degrade on the Ethernet link raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.117
opticsimAlarmEthSignalDegradeClearThis notification reports the signal degrade on the Ethernet link clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.118
opticsimAlarmEthPNACRaiseThis notification reports that the 'ethernet port-based authentication is failed' is raised.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.119
opticsimAlarmEthPNACClearThis notification reports that 'ethernet port-based authentication is failed' is cleared.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.120
opticsimAlarmAutomaticEthShutdownRaiseThis notification reports the 'Ethernet port shutdown' due not to local problems (on Ethernet port) but due to some problems on the associated interface on NE' defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.121
opticsimAlarmAutomaticEthShutdownClearThis notification reports the 'Ethernet port shutdown' due not to local problems (on Ethernet port) but due to some problems on the associated interface on NE' defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.122
opticsimAlarmEthFOPCMRaiseThis notification for 'Reception of an APS frame from the working transport entity for ethernet 1:1 EVC protection group' is raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.123
opticsimAlarmEthFOPCMClearThis notification for 'Reception of an APS frame from the working transport entity for ethernet 1:1 EVC protection group' is clear
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.124
opticsimAlarmEthFOPPMRaiseThis notification for 'Reception of an APS frame with incompatible -B- bit value' is raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.125
opticsimAlarmEthFOPPMClearThis notification for 'Reception of an APS frame with incompatible -B- bit value' is clear
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.126
opticsimAlarmEthFOPNRRaiseThis notification for 'Reception of an APS frame with incompatible -Requested Signal- value' is raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.127
opticsimAlarmEthFOPNRClearThis notification for 'Reception of an APS frame with incompatible -Requested Signal- value' is clear
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.128
opticsimAlarmEthFOPAMRaiseThis notification for 'Reception of an APS frame with incompatible -A- bit value' is raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.129
opticsimAlarmEthFOPAMClearThis notification for 'Reception of an APS frame with incompatible -A- bit value' is clear
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.130
opticsimAlarmEthFOPDMRaiseThis notification for 'Reception of an APS frame with incompatible -D- bit value' is raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.131
opticsimAlarmEthFOPDMClearThis notification for 'Reception of an APS frame with incompatible -D- bit value' is clear
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.132
opticsimAlarmEthNOSYNCRaiseThis notification for 'Loss Of synchronisation for ethernet port' is raise
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.133
opticsimAlarmEthNOSYNClearThis notification for 'Loss Of synchronisation for ethernet port' is clear
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.134
opticsimAlarmEthANMRaiseThis notification for 'Auto-Negotiation_Mismatch' is raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.135
opticsimAlarmEthANMClearThis notification for 'Auto-Negotiation_Mismatcht' is clear
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.136
opticsimAlarmHldOverRaiseThis notification for 'The system clock is in the holdover or free-running mode' is raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.137
opticsimAlarmHldOverClearThis notification for 'The system clock is in the holdover or free-running mode' is clear
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.138
opticsimTLURaiseThis notification for 'Timing Link Unequiped' is raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.139
opticsimTLUClearThis notification for 'Timing Link Unequiped' is clear
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.140
opticsimAlarmPDHTLCRRaiseThis notification for 'Total loss capacity in receive direction' is raise
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.141
opticsimAlarmPDHTLCRClearThis notification for 'Total loss capacity in receive direction' is clear
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.142
opticsimAlarmPDHTLCTRaiseThis notification for 'Total loss capacity in transmission direction' is raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.143
opticsimAlarmPDHTLCTClearThis notification for 'Total loss capacity in transmission direction' is clear
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.144
opticsimAlarmPDHPLCTRaiseThis notification for 'Patial loss capacity in transmission direction' is raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.145
opticsimAlarmPDHPLCTClearThis notification for 'Patial loss capacity in transmission direction' is clear
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.146
opticsimAlarmPDHPLCRRaiseThis notification for 'Patial loss capacity in receive direction' is raise
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.147
opticsimAlarmPDHPLCRClearThis notification for 'Patial loss capacity in receive direction' is clear
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.148
opticsimAlarmPDHMNDRaiseThis notification for 'Member not deskewable fault cause' is raise
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.149
opticsimAlarmPDHMNDClearThis notification for 'Member not deskewable fault cause' is clear
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.150
opticsIMRetimingBufferOverflowRaiseThis notification reports the 'Ethernet port shutdown' due not to local problems (on Ethernet port) but due to some problems on the associated interface on NE' defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.151
opticsIMRetimingBufferOverflowClearThis notification reports the 'Ethernet port shutdown' due not to local problems (on Ethernet port) but due to some problems on the associated interface on NE' defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.152
opticsimAlarmFailureOfProtocolProvisioningMismatchRaiseThis notification reports the Failure of protocol Provisioning Mismatch event raise
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.153
opticsimAlarmFailureOfProtocolProvisioningMismatchClearThis notification reports the Failure of protocol Provisioning Mismatch event clear
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.154
opticsimAlarmFailureOfProtocolTimeOutRaiseThis notification reports the Failure of protocol TimeOut event raise
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.155
opticsimAlarmFailureOfProtocolTimeOutClearThis notification reports the Failure of protocol TimeOut event clear
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.156
opticsimAlarmLoopingFrameEventRaiseThis notification reports the looping frame event raise
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.157
opticsimAlarmLoopingFrameEventClearThis notification reports the looping frame event clear
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.158
opticsimAlarmEthOAMMIPOverflowEventRaiseThis notification reports the MIP OverFlow event raise
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.159
opticsimAlarmEthOAMMIPOverflowEventClearThis notification reports the MIP OverFlow event clear
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.160
opticsimAlarmMcastTableOverflowEventRaiseThis notification reports the Multicast table OverFlow event raise
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.161
opticsimAlarmMcastTableOverflowEventClearThis notification reports the Multicast table OverFlow event clear
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.162
opticsimAlarmEthOAMVSFRaiseThis notification reports the VSF defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.163
opticsimAlarmEthOAMVSFClearThis notification reports the VSF defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.164
opticsIMAlarmExSERRaiseThis notification reports an excessive rate of symbol errors on the line. In case of 10GE interfaces it reports an excessive rate of invalid blocks. The threshold rate is configurable as maximum number of symbol errors/ invalid blocks in one second using the opticsIMlinkEnhSymbErrThr object in opticsIMlinkEnhTable.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.165
opticsIMAlarmExSERClearThis notification reports an excessive symbol error rate alarm clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.166
opticsIMAlarmLossOfCESoETHFrameRaiseThis notification reports the loss of CES Frame (LCF) defect raise
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.167
opticsIMAlarmLossOfCESoETHFrameClearThis notification reports the loss of CES Frame (LCF) defect clear
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.168
opticsimAlarmLossOfProtectionRaiseThis notification reports the loss of protection defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.169
opticsimAlarmLossOfProtectionClearThis notification reports the loss of protection defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.170
opticsIMAlarmAisTxRaiseThis notification reports the AIS in Tx direction defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.171
opticsIMAlarmAisTxClearThis notification reports the AIS in Tx direction defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.172
opticsIMAlarmAisRxRaiseThis notification reports the AIS in Rx direction defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.173
opticsIMAlarmAisRxClearThis notification reports the AIS in Rx direction defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.174
opticsIMAlarmUrdRaiseThis notification reports the Underline Resource Degraded (URD) defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.175
opticsIMAlarmUrdClearThis notification reports the Underline Resource Degraded (URD) defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.176
opticsIMAlarmUrusRaiseThis notification reports the Underline Resource Unavailable Service (URUS) defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.177
opticsIMAlarmUrusClearThis notification reports the Underline Resource Unavailable Service (URUS) defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.178
opticsIMAlarmLossOfESMCRaiseThis notification reports the Loss of Ethernet Synchronisation Messaging Channel defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.179
opticsIMAlarmLossOfESMCClearThis notification reports the Loss of Ethernet Synchronisation Messaging Channel defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.180
opticsIMAlarmStraypacketsRaiseThis notification reports the Stray Packets defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.181
opticsIMAlarmStraypacketsClearThis notification reports the Stray Packets defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.182
opticsIMAlarmExcessivepacketLossRaiseThis notification reports the Excessive Packet Loss defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.183
opticsIMAlarmExcessivepacketLossClearThis notification reports the Excessive Packet Loss Rate defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.184
opticsIMAlarmRemotepacketlossRaiseThis notification reports the Remote Packet Loss defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.185
opticsIMAlarmRemotepacketlossClearThis notification reports the Remote Packet Loss defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.186
opticsIMAlarm1PpsTodLOSRaiseThe alarm is raised if 1PPS pulse can't be detected within 3s time if the 1PPS/TOD interface is enabled..
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.187
opticsIMAlarm1PpsTodLOSClearThe alarm is cleared if 1PPS signal can be detected within 1s time for consecutive 3s timeline.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.188
opticsIMAlarm1PpsToDDEGRaiseThe alarm is raised if 1PPS pulse can be received within 1s time (not 1PPS/TOD LOS) but the operational status of 1PPS is degraded and the 1PPS/TOD interface is enabled.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.189
opticsIMAlarm1PpsToDDEGClearThe alarm is cleared if 1PPS pulse can be received within 1s time (not 1PPS/TOD LOS) and the operational status of 1PPS/ToD is normal.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.190
opticsIMAlarmPtpLossOfLockRaiseThe alarm is raised if PTP recovered Clock state is NOT in LOCKED state and the PTP port is enabled.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.191
opticsIMAlarmPtpLossOfLockClearThe alarm is cleared if PTP recovered Clock state is in LOCKED state.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.192
opticsIMAlarmPtpFaultyRaiseThe alarm is raised if PTP port is in Faulty and the PTP port is enabled.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.193
opticsIMAlarmPtpFaultyClearThe alarm is cleared if PTP recovered Clock state is NOT in Faulty state.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.194
opticsIMAlarmInvalidTdmDataRaiseThis notification reports that the 'L' bit is set in SAToP Control Word, it indicate that TDM data carried in the payload is invalid due to an attachment circuit fault.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.195
opticsIMAlarmInvalidTdmDataClearThis notification reports that the 'L' bit is cleared in SAToP Control Word:.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.196
opticsIMAlarmIncompatibleProtectionRaiseThis notification reports the raise of the incompatibility between equipment for protection scope.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.197
opticsIMAlarmIncompatibleProtectionClearThis notification reports the clear of the incompatibility between equipment for protection scope.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.198
opticsIMAlarmBandwidthDegradeForProtectionSwitchRaiseThis notification reports the raise of the bandwidth degrade in case of protection switch.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.199
opticsIMAlarmBandwidthDegradeForProtectionSwitchClearThis notification reports the clear of the bandwidth degrade in case of protection switch.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.200
opticsIMAlarmDuplicatedAddressDetectedRaiseThis notification reports the raise of the detection of an IP address duplication.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.201
opticsIMAlarmDuplicatedAddressDetectedClearThis notification reports the clear of the detection of an IP address duplication.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.202
opticsIMAlarmLoopbackPresenceRaiseThis notification reports the raise of the loopback alarm presence.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.203
opticsIMAlarmLoopbackPresenceClearThis notification reports the clear of the loopback alarm presence.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.204
opticsIMAlarmServiceSelectiveDropRaiseThis notification reports the raise of the service selective drop .
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.205
opticsIMAlarmServiceSelectiveDropClearThis notification reports the clear of the service selective drop.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.206
opticsimAlarmlnkaggExBandwidthDegradeRaiseThis notification reports the raise of the LAG Excessive Bandwidth Degrade alarm presence.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.207
opticsimAlarmlnkaggExBandwidthDegradeClearThis notification reports the clear of the LAG Excessive Bandwidth Degrade alarm presence.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.208
opticsIMAlarmRemoteFaultIndicationRaiseThis notification reports the Remote Fault Indication (RFI) defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.209
opticsIMAlarmRemoteFaultIndicationClearThis notification reports the Remote Fault Indication (RFI) defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.210
opticsIMAlarm1588AnnouncePktLOSRaiseThe alarm is raised if the 1588 Announce packet loss is detected, the default detect interval is 3 packets.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.211
opticsIMAlarm1588AnnouncePktLOSClearThe alarm is cleared if the 1588 Announce packet loss is not detected.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.212
opticsIMAlarm1588SyncPktLOSRaiseThe alarm is raised if the 1588 sync packet loss is detected, the default detect interval is 3 packets.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.213
opticsIMAlarm1588SyncPktLOSClearThe alarm is cleared if the 1588 sync packet loss is not detected.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.214
opticsIMAlarm1588DelayRespPktLOSRaiseThe alarm is raised if the 1588 Delay_resp packet is not received, the default detect interval is 3 packets.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.215
opticsIMAlarm1588DelayRespPktLOSClearThe alarm is cleared if the 1588 Delay_resp packet is received.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.216
opticsIMAlarm1588PTPClockclassDEGRaiseThe alarm is raised if PTP clockclass is smaller than the value of the specific threshold,and the value of 'stepsRemoved' for PTP reference source is '0', the default threshold value is 6.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.217
opticsIMAlarm1588PTPClockclassDEGClearThe alarm is cleared if PTP clockclass is bigger than the value of the specific threshold,or the value of 'stepsRemoved' for PTP reference source is not '0', the default threshold value is 6.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.218
opticsIMAlarmESMCPktLosRaiseThe alarm shall be raised if the ESMC packet is lost.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.219
opticsIMAlarmESMCPktLosClearThe alarm shall be cleared if the ESMC packet is received.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.220
opticsimAlarmLossOfPktSynchronizationRaiseThis notification reports the raise of the Loss Of CEP Packet Synchronization alarm presence.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.221
opticsimAlarmLossOfPktSynchronizationClearThis notification reports the clear of the Loss Of CEP Packet Synchronization alarm presence.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.222
opticsimAlarmExcessiveMissingPktRaiseThis notification reports the raise of the Excessive Missing CEP Packet alarm presence.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.223
opticsimAlarmExcessiveMissingPktClearThis notification reports the clear of the Excessive Missing CEP Packet alarm presence.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.224
opticsimAlarm1588TCFailRaiseThis notification reports the raise of the 1588 Transparent Clock Fail alarm presence.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.225
opticsimAlarm1588TCFailClearThis notification reports the clear of the 1588 Transparent Clock Fail alarm presence.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.226
opticsimAlarmTrafficDownRaiseThis notification reports the raise of the Traffic Down alarm presence.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.227
opticsimAlarmTrafficDownClearThis notification reports the clear of the Traffic Down alarm presence.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.228
opticsimAlarmTrafficLossRaiseThis notification reports the raise of the Traffic Loss alarm presence.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.229
opticsimAlarmTrafficLossClearThis notification reports the clear of the Traffic Loss alarm presence.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.230
opticsimAlarmRxProblemRaiseThis notification reports the raise of Rx Problem alarm presence.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.231
opticsimAlarmRxProblemClearThis notification reports the clear of the Rx Problem alarm presence.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.232
opticsimAlarmTxProblemRaiseThis notification reports the raise of the Tx Problem alarm presence.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.233
opticsimAlarmTxProblemClearThis notification reports the clear of the Tx Problem alarm presence.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.234
opticsimAlarmLagPortDownRaiseThis notification reports the raise of LAG Port Down alarm presence.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.235
opticsimAlarmLagPortDownClearThis notification reports the clear of the LAG Port Down alarm presence.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.236
opticsimAlarmCKMRaiseThis notification reports the raise of the Current Key Mismatch alarm presence.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.237
opticsimAlarmCKMClearThis notification reports the clear of the Current Key Mismatch alarm presence.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.238
opticsimAlarmNKMRaiseThis notification reports the raise of the Next Key Mismatch alarm presence.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.239
opticsimAlarmNKMClearThis notification reports the clear of the Next Key Mismatch alarm presence.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.240
opticsimAlarmAesFipsFailureRaiseThis notification reports the raise of the AES engine Failure alarm presence.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.241
opticsimAlarmAesFipsFailureClearThis notification reports the clear of the AES engine Failure alarm presence.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.242
opticsimAlarmSessionTimeoutRaiseThis notification reports the raise of the expiration (timeout) of the current manager session alarm presence.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.243
opticsimAlarmSessionTimeoutClearThis notification reports the clear of the expiration (timeout) of the current manager session alarm presence.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.244
opticsimThresholdOutputPowerHighRaiseThis notification reports the raise of warning condition of exceeding Threshold of transmitting Power too High.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.245
opticsimThresholdOutputPowerHighClearThis notification reports the clear of warning condition of exceeding Threshold of transmitting Power too High.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.246
opticsimThresholdOutputPowerLowRaiseThis notification reports the raise of warning condition of exceeding Threshold of transmitting Power too Low.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.247
opticsimThresholdOutputPowerLowClearThis notification reports the clear of warning condition of exceeding Threshold of transmitting Power too Low.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.248
opticsimThresholdInputPowerHighRaiseThis notification reports the raise of warning condition of exceeding Threshold of receiving Power too High.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.249
opticsimThresholdInputPowerHighClearThis notification reports the clear of warning condition of exceeding Threshold of receiving Power too High.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.250
opticsimThresholdInputPowerLowRaiseThis notification reports the raise of warning condition of exceeding Threshold of receiving Power too Low.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.251
opticsimThresholdInputPowerLowClearThis notification reports the clear of warning condition of exceeding Threshold of receiving Power too Low.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.252
opticsimInputPowerOverloadRaiseThis notification reports the raise of alarm condition of exceeding Threshold of receiving Power too High.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.253
opticsimInputPowerOverloadClearThis notification reports the clear of alarm condition of exceeding Threshold of receiving Power too High.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.254
opticsimAlarmESMRaiseThis notification reports the raise of the Encryption State Mismatch alarm presence.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.255
opticsimAlarmESMClearThis notification reports the clear the Encryption State Mismatch alarm presence.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.256
opticsimAlarmKeyUnavailableRaiseThis notification reports the raise of the encryption key not available (or missing) alarm presence.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.257
opticsimAlarmKeyUnavailableClearThis notification reports the clear of the encryption key not available (or missing) alarm presence.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.258
opticsimFreeLicenseRunningRaiseThis notification reports the raise of the alarm to advice that the node is working in normal mode but without license key (free license).
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.259
opticsimFreeLicenseRunningClearThis notification reports the clear of the alarm to advice that the node is working in normal mode but without license key (free license).
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.260
opticsimFreeLicenseExpiredRaiseThis notification reports the raise of the alarm to advice that the node is working in degraded mode for license missing.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.261
opticsimFreeLicenseExpiredClearThis notification reports the clear of the alarm to advice that the node is working in degraded mode for license missing.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.262
opticsIMAlarmStolenStatusRaiseThis notification reports the raise of the alarm for the node entered on Stolen Status.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.263
opticsIMAlarmStolenStatusClearThis notification reports the clear of the alarm for the node entered on Stolen Status.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.264
opticsIMAlarmEthOAMUnexpectedMepRaiseThis notification reports (Ethernet OAM Continuity Check) mismatch problems on CCM on receiving MEP.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.265
opticsIMAlarmEthOAMUnexpectedMepClearThis notification reports the clear of the (Ethernet OAM Continuity Check) mismatch problems on CCM on receiving MEP.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.266
opticsIMAlarmEthOAMMACStatusDefectRaiseThis notification reports the raise of the (Ethernet OAM Continuity Check) MAC Status defect.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.267
opticsIMAlarmEthOAMMACStatusDefectClearThis notification reports the clear of the (Ethernet OAM Continuity Check) MAC Status defect.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.268
opticsIMAlarmLogUploadFailureRaiseThis notification reports the raise of the Log Upload Failure defect.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.269
opticsIMAlarmLogUploadFailureClearThis notification reports the clear of the Log Upload Failure defect.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.270
opticsIMAlarmIpsecPskMissingRaiseThis notification reports the raise of the IPSec PSK (Pre Secret Key) missing defect.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.271
opticsIMAlarmIpsecPskMissingClearThis notification reports the clear of the IPSec PSK (Pre Secret Key) missing defect.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.272
opticsIMAlarmIpsecTunnelSetupFailureRaiseThis notification reports the raise of the IPSec tunnel set-up failure defect.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.273
opticsIMAlarmIpsecTunnelSetupFailureClearThis notification reports the clear of the IPSec tunnel set-up failure defect.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.274
opticsIMAlarmSecureSelfTestFailureRaiseThis notification reports the raise of the secure self-test failure defect.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.275
opticsIMAlarmSecureSelfTestFailureClearThis notification reports the clear of the secure self-test failure defect.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.276
opticsIMAlarmEthOAMUnexpectedCcmConnectivityRaiseThis notification reports the raise of the ETH OAM Unexpected CCM conectivity defect.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.277
opticsIMAlarmEthOAMUnexpectedCcmConnectivityClearThis notification reports the clear of the ETH OAM Unexpected CCM conectivity defect.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.278
opticsIMAlarmSecureModeMismatchRaiseThis notification reports the raise of the Secure mode mismatch defect.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.279
opticsIMAlarmSecureModeMismatchClearThis notification reports the clear of the Secure mode mismatch defect.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.280
opticsIMAlarmSWDLConditionalSelfTestFailRaiseThis notification reports the raise of the Sw Download Conditional Self test defect.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.281
opticsIMAlarmSWDLConditionalSelfTestFailClearThis notification reports the clear of the Sw Download Conditional Self test defect.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.282
opticsIMAlarmCRNGConditionalSelfTestFailRaiseThis notification reports the raise of the Conditional Random Number Generator (CRNG) Self test defect.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.283
opticsIMAlarmCRNGConditionalSelfTestFailClearThis notification reports the clear of the Conditional Random Number Generator (CRNG) Self test defect.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.284
opticsIMAlarmUpdateIPSecKeysFailRaiseThis notification reports the raise of the Update of IP Sec Key Fail alarm.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.285
opticsIMAlarmUpdateIPSecKeysFailClearThis notification reports the clear of the Update of IP Sec Key Fail alarm.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.286
opticsIMAlarmZeroizeIPSecKeysFailRaiseThis notification reports the raise of the Zeroize of the IP Sec Key Fail alarm.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.287
opticsIMAlarmZeroizeIPSecKeysFailClearThis notification reports the clear of the Zeroize of the IP Sec Key Fail alarm.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.288
opticsIMAlarmVESListenerConnectionFailureRaiseThis notification reports the raise of the alarm for problems to send VES events to Listener Collector .
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.289
opticsIMAlarmVESListenerConnectionFailureClearThis notification reports the clear of the alsrm for problems to send VES events to Listener Collector .
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.290
opticsIMAlarmMissingDiversityAlignConfRaiseThis notification reports the raise of the alarm for problems to send VES events to Listener Collector .
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.291
opticsIMAlarmMissingDiversityAlignConfClearThis notification reports the clear of the alsrm for problems to send VES events to Listener Collector .
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.292
opticsIMAlarmACMDegradeRaiseThis notification reports the raise of the alarm for ACM Degrade, when the max Modulation is not reached for a specific time period .
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.293
opticsIMAlarmACMDegradeClearThis notification reports the clear of the alarm for ACM Degrade.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.294
opticsIMAlarmLocalAutoTxMuteRaiseThis notification reports the raise of the alarm for auto mute.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.295
opticsIMAlarmLocalAutoTxMuteClearThis notification reports the clear of the alarm for auto mute.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.296
opticsIMAlarmLossOfContinuityRaiseThis notification reports the raise of the Loss Of Continuity alarm on the resource specified.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.297
opticsIMAlarmLossOfContinuityClearThis notification reports the clear of the Loss Of Continuity alarm on the resource specified.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.298
opticsIMAlarmPowerSavingActiveRaiseThis notification reports the activation of the Power Saving on the resource specified.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.299
opticsIMAlarmPowerSavingActiveClearThis notification reports the deactivation of the Power Saving on the resource specified.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.1.5.1.40.300
opticsIMdatabaseModifyThis attribute stores the information that a local operator has changed the configuration in a persistent way. It contains the date of the last time the LAC status has become granted.ro
TsdimEventTimeInt (TSDIM-SNMP-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.41
opticsimSwPackageProfileRequestedThis object is used for configuring the software package profile which indicates the network functionalities enabled on the NE. If the requested profile is compatible with the downloaded software, the configuration is accepted, the value is saved in the boot NE area and, when the NE has been restarted, the value will be effective and it will be mirrored in the opticsimSwPackageProfile, otherwise the error code badValue has to be returned. The value of this attribute is commonly agreed, its semantic will be described in the relevant Ext. Interface Management Specification.rw
Bits
.1.3.6.1.4.1.637.54.1.1.5.1.42
opticsIMPoolTableThis table defines the pools available in the node. The following pools are defined: poolID pool poolDescription -------------------------------------------------------------------- 1 Pool1 Packet Processor Bandwidth (kbit) 2 Pool2 Packet Processor CAM (Number of entries) 3 Pool3 Traffic Manager Logical Ports (number of ports) 4 Pool4 Traffic Descriptors (number of TD) 5 Pool5 InFlows (number of flows) 6 Pool6 OutFlows (number of flows) 7 Pool7 CrossConnections (number of XC) 8 Pool8 Link Aggregation Groups (number of LAG) 9 Pool9 Spanning Tree Instances (number of instances) 10 Pool10 Matrix channels (number of channels) 11 Pool11 Bandwidth for Remote Ports 12 Pool12 Ethernet classifiers (number of ETS Classifiers) 13 Pool13 Static VLAN registration entries (number of registered VLANs) 14 Pool14 (IVL/SVL)Dynamic Filtering Entries (number of dynamic entries) 15 Pool15 (IVL/SVL)Static Filtering Entries (number of static entries) 16 Pool16 IGMP Snooping Entries (number of IGMP Snooping Entries) 17 Pool17 MPLS InSegments (number of MPLS InSegments) 18 Pool18 MPLS OutSegments (number of MPLS OutSegments) 19 Pool19 MPLS Tunnels (number of MPLS Tunnels) 20 Pool20 MPLS Traffic Descriptors (number of MPLS Traffic Descriptors)
SEQUENCE OF OpticsIMPoolEntry
.1.3.6.1.4.1.637.54.1.1.5.1.43
opticsIMPoolEntryEach entry is a resource pool associated to a defined position (open to be extended). Description of entries: - positionID: it is the physical position of the board (e.g. slot). It is used as entry for the resources associated for example to the board configured in a slot. It is used positionID 0.0.0.0.0 (zero) to indicate pools for the whole Network element. - poolID: it is a unique identifier describing the pool; the association poolID - pool descriptor is provided in the behaviour. - nominalResources: the maximum number of resources available (by definition) - UsedResources: the number of used resources - availableResources: the current available resources (it's the nominal subtracted the used). - crossRelation: it is a field used when different items in the network element (e.g. different boards) share the same pools of resources. The typical case is when Access Card (providing physical access) are used. In this case the same pool information is repeated for the slots containing the main board and the access card itself and in correspondence to the access card slot entries, the crossRelation field indicates the slot related to the corresponding main board (and it is indicated also in correspondence of the main board crossRelation).
OpticsIMPoolEntry
.1.3.6.1.4.1.637.54.1.1.5.1.43.1
opticsIMpositionIDThis object defines the physical position of the board referenced by the pool.
OCTET STRING
.1.3.6.1.4.1.637.54.1.1.5.1.43.1.1
opticsIMpoolIDThis object defines the unique identifier describing the pool.
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.43.1.2
opticsIMPoolnominalResourcesThis object indicates the maximum number of resources available.ro
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.43.1.3
opticsIMPoolusedResourcesThis object indicates the number of used resources.ro
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.43.1.4
opticsIMPoolavailableResourcesThis object indicates the current available resources.ro
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.43.1.5
opticsIMPoolcrossRelationThis object is used when different items in the network element (e.g. different boards) share the same pools of resources. The typical case is when Access Card (providing physical access) are used. In this case the same pool information is repeated for the slots containing the main board and the access card itself and in correspondence to the access card slot entries, the crossRelation field indicates the slot related to the corresponding main board (and it is indicated also in correspondence of the main board crossRelation)the current available resources.ro
OCTET STRING
.1.3.6.1.4.1.637.54.1.1.5.1.43.1.6
opticsimNeMtuThis object reports 'on per NE basis' MTU (the size of the largest packet which can be sent/received on NE) specified in octets. For NE interfaces that are used for transmitting network datagrams, this is the size of the largest network datagram that can be sent on any NE interface. 'on per NE basis' MTU is mutually exclusive with 'on per port basis' MTU and is supported ONLY on NE without 'on per port basis' MTU provisioning. The value 0 (unknown) is the default value (with the meaning of no 'on per NE basis' MTU value). The support of 'on per NE basis' MTU is product specific and will be documented in the product external specificationrw
Unsigned32
.1.3.6.1.4.1.637.54.1.1.5.1.44
opticsIMNeMACCollection
OBJECT IDENTIFIER
.1.3.6.1.4.1.637.54.1.1.5.1.45
opticsIMNeMACCollectionStatusThis object defines the MAC collection NE status: 2 operating status have been defined: the <Ready_for_Request> status, the <In_Preparation> status and the <File_Transfer_Completed> status; the default status is <Ready_for_Request>ro
Enumeration
.1.3.6.1.4.1.637.54.1.1.5.1.45.1
opticsIMNeMACActivateCollectionThis object defines the start of the MAC collection on NE: the value <NormalStart> is set by manager in order to activate the MAC collection in normal condition; the value <ForcedStart> is set by manager in order to activate the MAC collection in abnormal condition (for instance when NE is still preparing a previous commanded MAC collection); the agent will reset the value to <Noop> when the manager setting has been recognized. The default value is the <Noop> one.rw
Enumeration
.1.3.6.1.4.1.637.54.1.1.5.1.45.2
opticsIMIfQueueTableThis table contains objects for each Forwarding queue of a NE interface.
SEQUENCE OF OpticsIMIfQueueEntry
.1.3.6.1.4.1.637.54.1.1.5.1.46
opticsIMIfQueueEntryAn entry references a forwarding Queue on each NE interface
OpticsIMIfQueueEntry
.1.3.6.1.4.1.637.54.1.1.5.1.46.1
opticsIMIfQueueNumberThe number of the forwarding queue within the forwarding queue set
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.46.1.1
opticsIMIfQueueTypeThe type of the forwarding queuerw
Enumeration
.1.3.6.1.4.1.637.54.1.1.5.1.46.1.2
opticsIMIfQueueWeightThe weight assigned to a weighted bandwidth forwarding queue; the returned value is meaningful ONLY for a weighted bandwidth forwarding queuerw
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.46.1.3
opticsIMIfQueueNominalBandwidthThis attribute reports (in kbit/sec): - bandwidth parameter as inferred from assigned weight (in case of an egress weighted bandwidth Forwarding Queue); - Egress Link nominal bandwidth (in case of an egress strict priority Forwarding Queue)ro
Gauge32
.1.3.6.1.4.1.637.54.1.1.5.1.46.1.4
opticsIMIfQueueAvailableBandwidthThis attribute reports (in kbit/sec): - Available bandwidth parameter (in case of an egress weighted bandwidth Forwarding Queue); - Egress Link Available bandwidth (in case of an egress strict priority Forwarding Queue)ro
Gauge32
.1.3.6.1.4.1.637.54.1.1.5.1.46.1.5
opticsIMIfQueueSlopeHiAdminStatusopticsIMIfQueueSlopeHiAdminStatus specifies the admin state for the Green packets (high priority) WRED slope. If the opticsIMIfQueueSlopeHiAdminStatus is set to 'down', the WRED slope is inactive. Default value is downrw
Enumeration
.1.3.6.1.4.1.637.54.1.1.5.1.46.1.6
opticsIMIfQueueSlopeHiStartAverageThe percentage (0..100) of the buffer utilized after which the drop probability of Green packets starts to rise above 0. Default value is 70rw
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.46.1.7
opticsIMIfQueueSlopeHiMaxAverageThe percentage (0..100) of the buffer utilized after which the drop probability of Green packets is 100 percent. This implies that all Green packets beyond this point will be dropped.Default value is 90rw
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.46.1.8
opticsIMIfQueueSlopeHiMaxProbabilityThe drop probability (0..100) of Green packets increases steadily from 0 (at opticsIMIfQueueSlopeHiStartAverage) up to opticsIMIfQueueSlopeHiMaxProbability (at the opticsIMIfQueueSlopeHiMaxAverage). Default value is 80rw
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.46.1.9
opticsIMIfQueueSlopeLoAdminStatusopticsIMIfQueueSlopeLoAdminStatus specifies the admin state for the Yellow packet (Low priority) WRED slope. If opticsIMIfQueueSlopeLoAdminStatus is set to 'down', the WRED slope is inactive.Default value is downrw
Enumeration
.1.3.6.1.4.1.637.54.1.1.5.1.46.1.10
opticsIMIfQueueSlopeLoStartAverageThe percentage (0..100) of the buffer utilized after which the drop probability of Yellow packet starts to rise above 0. Default value is 50rw
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.46.1.11
opticsIMIfQueueSlopeLoMaxAverageThe percentage of the buffer utilized after which the drop probability of Yellow packets is 100 percent. This implies that all packets beyond this point will be dropped. Default is 75rw
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.46.1.12
opticsIMIfQueueSlopeLoMaxProbabilityThe drop probability (0..100) of Yellow packets increases steadily from 0 (at opticsIMIfQueueSlopeLoStartAverage) up to opticsIMIfQueueSlopeLoMaxProbability (at the opticsIMIfQueueSlopeLoMaxAverage).Default is 80rw
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.46.1.13
opticsIMIfQueueSizeThis object is the buffer size of the queue in bytes as defined by managing system.rw
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.46.1.14
opticsIMIfQueueDefaultSizeThis object reports to the managing system the default value for the buffer size of the queue as applied by the agent.ro
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.46.1.15
opticsIMIfEgressFCMappingTable
SEQUENCE OF OpticsIMIfEgressFCMappingEntry
.1.3.6.1.4.1.637.54.1.1.5.1.47
opticsIMIfEgressFCMappingEntryThis entry contains information about mappings of a particular forwarding class (including BOTH Green and Yellow packets) to a forwarding queue
OpticsIMIfEgressFCMappingEntry
.1.3.6.1.4.1.637.54.1.1.5.1.47.1
opticsIMIfEgressFCNumberThe number of the Forwarding Class: Forwarding Classes are numbered starting from 0 to 7 with increasing forwarding priority (Forwarding Class 0 with lowest forwarding priority)
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.47.1.1
opticsIMIfEgressFCQueuethe Forwarding queue to use for packets in this forwarding class: Forwarding Queues are numbered starting from 0 to N (Forwarding Queue 0 with lowest priority queue)rw
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.47.1.2
opticsIMNeSLATypeopticsIMNeSLAType specifies 'on per NE basis' the type of ETS Traffic Descriptors to be applied on each board in 'multi-board NE' supporting multi-board Link Aggregation Interface. In case of full opticsIMNeSLAType the same ETS Traffic Descriptor (for an ETS InFlow over a Link Aggregation Interface) is applied with full Traffic Descriptor Parameters(CIR,PIR) to each board supporting at least one Aggregation Port inside Link Aggregation Interface. In case of fractional opticsIMNeSLAType different instances of ETS Traffic Descriptor (for an ETS InFlow over a Link Aggregation Interface) are applied with fractional Traffic Descriptor Parameters(CIR,PIR) to each board supporting at least one Aggregation Port inside Link Aggregation Interface. Default value is fullrw
Enumeration
.1.3.6.1.4.1.637.54.1.1.5.1.48
opticsimLinkOAMLogMinIntervalThis parameter defines the granularity window (sec) for the logging of LinkOAM event in the dot3OamEventLogTable. If more events of the same type are to be logged in this table in the window specified by this object, only the first one shall be logged.rw
INTEGER
.1.3.6.1.4.1.637.54.1.1.5.1.49
opticsIMNeAlarmsTableTable for management of the ASAP object related to NE-level alarms. This table always contains only 1 single entry, with index value 1.
SEQUENCE OF OpticsIMNeAlarmsEntry
.1.3.6.1.4.1.637.54.1.1.5.1.52
opticsIMNeAlarmsEntryEntry of table opticsIMNeAlarmsTable.
OpticsIMNeAlarmsEntry
.1.3.6.1.4.1.637.54.1.1.5.1.52.1
opticsIMNeAlarmsNeIndexUnique index for opticsIMNeAlarmsEntry. Only value 1 will be used.
OpticsIMNeAlarmsNeIndex
.1.3.6.1.4.1.637.54.1.1.5.1.52.1.1
opticsIMNeAlarmsAsapIndexThis object contains the ASAP object associated to the NE.rw
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.52.1.2
opticsIMCfmStatusThis object modifies the global enable status of CFM. The default is cfmDisable (0). In addition, when the status is disable, the first Maintenance Domain (MD) creation changes the status to enable, and when the status is enable, the last MD deletion changes the status to disable.rw
Enumeration
.1.3.6.1.4.1.637.54.1.1.5.1.53
opticsIMNeFrameSizeModeopticsIMNeFrameSizeMode specifies 'on per NE basis' the type of ingress policer, egress shaper and Performance Monitoring counters to be applied to all NE ports: - native: Policer and Ingress Performance Monitoring counters are BOTH based on NE-product specific value on Ingress Port Shaper and Egress Performance Monitoring counters are BOTH based on NE-product specific value on Egress Port - layer1: Ingress Policer, Egress Shaper and Ingress/Egress Performance Monitoring counters are based on Layer1 - layer2: Ingress Policer, Egress Shaper and Ingress/Egress Performance Monitoring counters are based on Layer2. Default value is NE-product specificrw
Enumeration
.1.3.6.1.4.1.637.54.1.1.5.1.54
opticsIMNeSyncEthEnableopticsIMNeSyncEthEnable specifies 'on per NE basis'enabled/disabled Ethernet Sync. Default value is false (Free running mode)rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.55
opticsIMCapabilityProfileTableThis table contains a list of capability.
SEQUENCE OF OpticsIMCapabilityProfileEntry
.1.3.6.1.4.1.637.54.1.1.5.1.56
opticsIMCapabilityProfileEntryAn entry of the opticsIMCapabilityProfileTable.
OpticsIMCapabilityProfileEntry
.1.3.6.1.4.1.637.54.1.1.5.1.56.1
opticsIMCapabilityProfileProfIndexThe value of this object is equal to opticsIMcapabilityProfileProfIndex in the opticsIMCapabilityProfileTable.
OpticsIMcapabilityProfileIndex
.1.3.6.1.4.1.637.54.1.1.5.1.56.1.1
opticsIMCapabilityProfileCapIndexThe value of this object is equal to opticsIMCapabilityProfileCapIndex in the opticsIMCapabilityProfileTable.
OpticsIMCapabilityIndex
.1.3.6.1.4.1.637.54.1.1.5.1.56.1.2
opticsIMCapabilityProfileCapUserLabelName of the capability. List of possible values is defined in reference documentro
OpticsIMUserLabel (TSDIM-SNMP-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.56.1.3
opticsIMCapabilityProfileCapInfoInformation about capability. List of possible values is defined in reference documentro
OCTET STRING
.1.3.6.1.4.1.637.54.1.1.5.1.56.1.4
opticsIMSwitchTableThis table contains objects for each Switch Instannce .
SEQUENCE OF OpticsIMSwitchEntry
.1.3.6.1.4.1.637.54.1.1.5.1.57
opticsIMSwitchEntryAn entry in this table represents an Ethernet Switch instance. It is autocreated/autodeleted by agent when a card is provisioned with switch instance
OpticsIMSwitchEntry
.1.3.6.1.4.1.637.54.1.1.5.1.57.1
opticsIMSwitchIndexThe index for switch Table.
INTEGER
.1.3.6.1.4.1.637.54.1.1.5.1.57.1.1
opticsIMSwitchIDUniquely identifies a Ethernet switch instance , the initial value starts from 0 .ro
INTEGER
.1.3.6.1.4.1.637.54.1.1.5.1.57.1.2
opticsIMSwitchOperationModeIndicates what types of mechanism this Bridge perfoms. none (1) This NE cannot perform any bridge mechanism bridge8021D (2) This Bridge performs 802.1D mechanism and can not support VLAN bridge8021Q (3) This Bridge performs 802.1Q mechanism bridge8021ad (4) This Bridge performs 802.1ad mechanism. The default value is bridge8021ad(4).rw
Enumeration
.1.3.6.1.4.1.637.54.1.1.5.1.57.1.3
opticsIMSwitchEthOamBridgeMACThe MAC address of the Bridge that is used as ETH OAM messages MAC SA.ro
MacAddress (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.57.1.4
opticsIMSwitchEthOamLbmReplyTimeoutThe LBR timeout after the corresponding LBM has been sent. It is measured in seconds in the range [1-30], with default =5.rw
INTEGER
.1.3.6.1.4.1.637.54.1.1.5.1.57.1.5
opticsIMSwitchEthOamLbmTxIntervalThe interval between two LBM frames sent. It is measured in 100 milli-second in the range [1-100]*100 ms, with default = 1second.rw
INTEGER
.1.3.6.1.4.1.637.54.1.1.5.1.57.1.6
opticsIMSwitchLinkOAMLogMinIntervalThis parameter defines the granularity window (sec) for the logging of LinkOAM event in the dot3OamEventLogTable. If more events of the same type are to be logged in this table in the window specified by this object, only the first one shall be logged. The default value is product specific .rw
INTEGER
.1.3.6.1.4.1.637.54.1.1.5.1.57.1.7
opticsIMSwitchPBProfileThis object defines 'on per Switch basis' admitted Provider Bridge profiles with below values: - 5P3D (1) - Default value, - 8P0D (2), - 7P1D (3), - 6P2D (4), - Customer-defined profile1 (5) whose support is NE product specificrw
INTEGER
.1.3.6.1.4.1.637.54.1.1.5.1.57.1.8
opticsIMSwitchTpAgingTimeThe timeout period in seconds (Range: 10..1000000) for aging out dynamically learned forwarding information. 802.1D-1998 recommends a default of 300 seconds. A value of 0x7FFFFFFF indicates aging disabled.rw
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.57.1.9
opticsIMSwitchTpLearnedEntryDiscardsThe total number of Forwarding Database entries, which have been or would have been learnt, but have been discarded due to a lack of space to store them in the Forwarding Database. If this counter is increasing, it indicates that the Forwarding Database is regularly becoming full (a condition which has unpleasant performance effects on the subnetwork). If this counter has a significant value but is not presently increasing, it indicates that the problem has been occurring but is not persistent.ro
Counter32
.1.3.6.1.4.1.637.54.1.1.5.1.57.1.10
opticsIMSwitchSTPTypeSTP Type configuration: - manualDisable (1) is used to disable the protocol for the bridge - stp(2) is used to enable STP and synchronously the Rapid STP is disabled - rstp(3) is used to enable Rapid STP and synchronously STP is disabled - pervlanrstp(4) is used to enable per-VLAN RSTP - mstp(5) is used to enable RSTP-based MSTP - rstpPlus (6) is used to enable further optimization for RSTP - mstpPlus (7) is used to enable further optimization for MSTP. The default value is product specific .rw
Enumeration
.1.3.6.1.4.1.637.54.1.1.5.1.57.1.11
opticsIMSwitchCfmMaTableNextIndexValue to be used as the index of the MA table when the management entity wants to create a new row in the table.ro
Gauge32
.1.3.6.1.4.1.637.54.1.1.5.1.57.1.12
opticsIMSwitchLocationit will be master slot in stack mode. RRSSBBDD RR- Rack SS- Subrack BB- Slot DD- Drawer.ro
INTEGER
.1.3.6.1.4.1.637.54.1.1.5.1.57.1.13
opticsIMSwitchBridgeFilteringModeThe Type of VLAN learning mode.When the object value is modified, the static fid-vlan mappings and static unicast entries need to be reconfigured. Static unicast configurations associated with old fid will get deleted. The default value is ivl(1) .rw
Enumeration
.1.3.6.1.4.1.637.54.1.1.5.1.57.1.14
opticsIMSwitchUserLabelThe canonical name assigned to Switch Instance.rw
OpticsIMUserLabel (TSDIM-SNMP-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.57.1.15
opticsIMSwitchPortTableThis table contains Ethernet switch ports associated to each Ethernet switch instance.
SEQUENCE OF OpticsIMSwitchPortEntry
.1.3.6.1.4.1.637.54.1.1.5.1.58
opticsIMSwitchPortEntryAn entry in this table represents an switch port. Being read-only table, it is autocreated by agent when an instance within opticsIMSwitchEntry is allocated with the port associated
OpticsIMSwitchPortEntry
.1.3.6.1.4.1.637.54.1.1.5.1.58.1
opticsIMSwitchPortIndexThe ifIndex value of the interface.
InterfaceIndex (IF-MIB)
.1.3.6.1.4.1.637.54.1.1.5.1.58.1.1
opticsIMSwitchPortMapStatusSwitch Port Entry status. This object is always equal to 0. It is a dummy object needed to have something to retrievero
INTEGER
.1.3.6.1.4.1.637.54.1.1.5.1.58.1.2
opticsIMTACACSServerManagement
OBJECT IDENTIFIER
.1.3.6.1.4.1.637.54.1.1.5.1.59
opticsIMTACACSServerTableThe TACACS server table. This table contains all the TACACS servers configured on the NE.
SEQUENCE OF OpticsIMTACACSServerEntry
.1.3.6.1.4.1.637.54.1.1.5.1.59.1
opticsIMTACACSServerEntryEntry is automatically created by Agent when a new TACACS server is configured on NE.
OpticsIMTACACSServerEntry
.1.3.6.1.4.1.637.54.1.1.5.1.59.1.1
opticsIMTACACSServerIndexThis is the index for the TACACS Server table.
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.59.1.1.1
opticsIMTACACSServerFailureCountThis is the number of the tentative to access to this TACACS server with negative result.ro
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.59.1.1.2
opticsIMTACACSLastServerUsedThis object reports the opticsIMTACACSServerIndex value of the last TACACS server reachable and used for Authentication/Authotization/Accounting access to the NE.ro
Integer32
.1.3.6.1.4.1.637.54.1.1.5.1.59.2
opticsIMTACACSAuthenticationThis object defines the actual user credential repository used for Authentication/Authotization/Accounting access to the NE.ro
Enumeration
.1.3.6.1.4.1.637.54.1.1.5.1.59.3
opticsIMRateLimitingProfileTableThis table contains objects for a rate limiting profile of a NE interface.
SEQUENCE OF OpticsIMRateLimitingProfileEntry
.1.3.6.1.4.1.637.54.1.1.5.1.60
opticsIMRateLimitingProfileEntryAn entry references, on port basis, a rate limiting profile.
OpticsIMRateLimitingProfileEntry
.1.3.6.1.4.1.637.54.1.1.5.1.60.1
opticsIMRLProfileVlanThe VLAN value associated to this profile. Values between 0 to 4095 indicate the actual VLAN field value. A value of 4096 indicates that the object refer to untagged frames, i.e. frames without 802.1Q field. A value of 4097 indicates that the VLAN field is not relevant, both if valued and if not present.rw
Unsigned32
.1.3.6.1.4.1.637.54.1.1.5.1.60.1.1
opticsIMRLProfilePCPThe PCP value associated to this profile.rw
Enumeration
.1.3.6.1.4.1.637.54.1.1.5.1.60.1.2
opticsIMRLProfileCommittedRateThe committed rate associated to this profile.rw
Gauge32
.1.3.6.1.4.1.637.54.1.1.5.1.60.1.3
opticsIMRLProfileCommittedBurstSizeThe committed size associated to this profile.rw
Gauge32
.1.3.6.1.4.1.637.54.1.1.5.1.60.1.4
opticsIMRLProfileRowStatusFor creating and deleting this row.rw
RowStatus (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.60.1.5
tsdimSnmpAgtIPv6AddressThis scalar object defines the Agent Ip Address in IPv6 formatrw
InetAddressIPv6 (TSDIM-SUPPORT-MIB)
.1.3.6.1.4.1.637.54.1.1.5.1.61
opticsIMNeOverClockedModeEnableopticsIMNeOverClockedModeEnable specifies 'on per NE basis'enabled/disabled OverClocked Mode Default value is false (No over-clocked mode)rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.1.5.1.64
opticsIMNeAlarmAdminopticsIMNeAlarmAdmin specifies 'on per NE basis' Alarm Admin value. Default value is mon(1)rw
Enumeration
.1.3.6.1.4.1.637.54.1.1.5.1.65
opticsIMIfQueueWREDAdminStatusopticsIMIfQueueWREDAdminStatus specifies the admin state for the WRED slope. If the opticsIMIfQueueWREDAdminStatus is set to 'down', the WRED slope is inactive. Default value is downrw
Enumeration
.1.3.6.1.4.1.637.54.1.1.5.1.66
opticsIMMaintenanceModeopticsIMNEMaintenanceMode set to 'enable' means the NE is entering in a Maintenance mode.rw
Enumeration
.1.3.6.1.4.1.637.54.1.1.5.1.67
tsdimSnmpNEMCConf
OBJECT IDENTIFIER
.1.3.6.1.4.1.637.54.1.1.99.2
tsdimSnmpNEMCCompl
OBJECT IDENTIFIER
.1.3.6.1.4.1.637.54.1.1.99.2.1
tsdimSnmpNEMcThis module compliance describes a set of objects required for TSD-IM SNMP Agent implementation. These objects are defined inside tsdimSnmpNEMib
Unknown
.1.3.6.1.4.1.637.54.1.1.99.2.1.1
tsdimSnmpNEMCGroup
OBJECT IDENTIFIER
.1.3.6.1.4.1.637.54.1.1.99.2.2
tsdimSnmpNEGroupThis group describes the objects needed for the SNMP NE Configuration.
Unknown
.1.3.6.1.4.1.637.54.1.1.99.2.2.1
tsdimLacSupportGroupThis group describes the objects needed for Lac Configuration.
Unknown
.1.3.6.1.4.1.637.54.1.1.99.2.2.6
opticsIMACDGroupThis group describes the objects needed for the resource assignment functionality.
Unknown
.1.3.6.1.4.1.637.54.1.1.99.2.2.7
opticsIMIfExtGroupA collection of objects providing extensions for the configuration of an interface.
Unknown
.1.3.6.1.4.1.637.54.1.1.99.2.2.8
opticsIMAlarmGroupThis group describes the alarm notifications
Unknown
.1.3.6.1.4.1.637.54.1.1.99.2.2.9
opticsIMTptCoordinatorGroupA collection of objects providing configuration information for the TPT Coordinator objects.
Unknown
.1.3.6.1.4.1.637.54.1.1.99.2.2.10
opticsIMNeConfigurationGroupThis group describes the objects needed for NE configuration.
Unknown
.1.3.6.1.4.1.637.54.1.1.99.2.2.11
opticsIMSnmpNETimeGroupThis group describes the object used to manage the NE time, when NTP is not supported.
Unknown
.1.3.6.1.4.1.637.54.1.1.99.2.2.12
opticsIMNTPGroupThis group describes the objects related to the NTP management.
Unknown
.1.3.6.1.4.1.637.54.1.1.99.2.2.13
opticsIMOptAlarmGroupThis group describes the alarm notifications
Unknown
.1.3.6.1.4.1.637.54.1.1.99.2.2.14
opticsIMNePMCollectionGroupThis group describes the objects needed for NE PM Collection.
Unknown
.1.3.6.1.4.1.637.54.1.1.99.2.2.15
TSDIM-SNMPNE-MIB - SNMP MIB Reference | MIBs Explorer