TSDIM-SUPPORT-MIB
TSD-IM Support MIB
Main OID:
tsdimSupportMib.1.3.6.1.4.1.637.54.1.1.3
298
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
298 total| Object Name |
|---|
tsdimSupportMibTSD-IM Support MIB MODULE-IDENTITY .1.3.6.1.4.1.637.54.1.1.3 |
tsdimSupportMibObject OBJECT IDENTIFIER .1.3.6.1.4.1.637.54.1.1.3.1 |
tsdimMaxNotificationIdThis is the maximum value of the notification identifier counter generated by SNMP NE. The next notification identifier value, after this maximum value will be equal to one because the counter has wrapped.ro TsdimNotificationId (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.1 |
tsdimAPTTableThis table defines the TSDIM APT table. This table is used by Agent in order to store the active alarms, managing system can only read them. SEQUENCE OF TsdimAPTEntry .1.3.6.1.4.1.637.54.1.1.3.1.2 |
tsdimAPTEntryInformation about a single alarm in the APT. Entries in this table are created by SNMP NE and will be automatically deleted by SNMP NE when it is genereted a cleared-alarm. TsdimAPTEntry .1.3.6.1.4.1.637.54.1.1.3.1.2.1 |
tsdimAPTAlarmProbableCauseSee textual conventions.ro TsdimAlmProbableCause (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.2.1.1 |
tsdimAPTAlarmObjectClassIdentifierSee textual conventions.ro TsdimObjectClassId (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.2.1.2 |
tsdimAPTAlarmObjectInstanceIdentifierSee textual conventions.ro TsdimObjectInstanceId (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.2.1.3 |
tsdimAPTAlarmNotificationIdSee textual conventions. TsdimNotificationId (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.2.1.4 |
tsdimAPTAlarmSeveritySee textual conventions.ro TsdimAPTAlmSeverity (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.2.1.6 |
tsdimAPTAlarmSpecificProbSee textual conventions. This object is only present if it was included in the alarm trap corresponding to this APT entry.ro TsdimAlmSpecProblem (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.2.1.7 |
tsdimAPTAlarmTimeIndexSee textual conventions. TsdimEventTimeInt (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.2.1.11 |
opticsIMAPTAdditionalTextro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.2.1.12 |
opticsIMAPTAlarmTypero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.2.1.13 |
tsdimAPTAlarmTimeThis optional object indicates when the alarm has been generated.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.2.1.14 |
tsdimLogTableThis table defines the characteristics of the logs, both alarms and events, currently maintained by the agent. It is a common table that describes the behavior of the two logs, in-fact it contains generic attributes not related to the type of records stored inside logs. SEQUENCE OF TsdimLogEntry .1.3.6.1.4.1.637.54.1.1.3.1.3 |
tsdimLogEntryInformation about the characteristics of a single log. TsdimLogEntry .1.3.6.1.4.1.637.54.1.1.3.1.3.1 |
tsdimLogIndexIndicates the index of the log. Integer32 .1.3.6.1.4.1.637.54.1.1.3.1.3.1.1 |
tsdimLogObjectClassIdentifierThis object defines the SNMP entry table object identity of the log of which this row is referred to.ro OBJECT IDENTIFIER .1.3.6.1.4.1.637.54.1.1.3.1.3.1.2 |
tsdimLogAdminStatusSee textual conventions.rw TsdimAdministrativeState (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.3.1.3 |
tsdimLogOperStatusSee textual conventions.ro TsdimOperationalState (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.3.1.4 |
tsdimLogMaxSizeIndicates the maximum size of the log. This value specifies the maximum number of records that can be stored inside the logro Integer32 .1.3.6.1.4.1.637.54.1.1.3.1.3.1.5 |
tsdimEventLogTableThis table contain information about single event notification not alarm. Entries in this table are created automatically by Agent and they are never deleted because the Log behavior is automatically set to Wrap, hence when no more entry will be created (log full) new log entry will cause the deletion of the oldest one. SEQUENCE OF TsdimEventLogEntry .1.3.6.1.4.1.637.54.1.1.3.1.4 |
tsdimEventLogEntryAn entry in the tsdimEventLogTable TsdimEventLogEntry .1.3.6.1.4.1.637.54.1.1.3.1.4.1 |
tsdimEventLogEventTypeThis object describes the type of the event logged.ro Enumeration .1.3.6.1.4.1.637.54.1.1.3.1.4.1.1 |
tsdimEventLogObjectClassIdentifierSee textual conventions.ro TsdimObjectClassId (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.4.1.2 |
tsdimEventLogObjectInstanceIdentifierSee textual conventions.ro TsdimObjectInstanceId (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.4.1.3 |
tsdimEventLogNotificationIdSee textual conventions. TsdimNotificationId (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.4.1.4 |
tsdimEventLogEventTimeIndexSee textual conventions. TsdimEventTimeInt (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.4.1.6 |
opticsIMEventLogAdditionalTextro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.4.1.7 |
tsdimEventLogTimeThis optional object indicates when the event has been generated.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.4.1.9 |
tsdimAlarmLogTableThis table defines the TSDIM Alarm Log table. It is used to store the alarms generated by SNMP NE. SEQUENCE OF TsdimAlarmLogEntry .1.3.6.1.4.1.637.54.1.1.3.1.5 |
tsdimAlarmLogEntryEach entry contains information about single alarm notification. Entries in this table are created automatically by Agent and they are never deleted because the Log behavior is automatically set to Wrap, hence when no more entry will be created (log full) new log entry will cause the deletion of the oldest one. TsdimAlarmLogEntry .1.3.6.1.4.1.637.54.1.1.3.1.5.1 |
tsdimAlarmLogProbableCauseSee textual conventions.ro TsdimAlmProbableCause (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.5.1.1 |
tsdimAlarmLogObjectClassIdentifierSee textual conventions.ro TsdimObjectClassId (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.5.1.2 |
tsdimAlarmLogObjectInstanceIdentifierSee textual conventions.ro TsdimObjectInstanceId (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.5.1.3 |
tsdimAlarmLogNotificationIdSee textual conventions. TsdimNotificationId (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.5.1.4 |
tsdimAlarmLogSeverityThe perceived severity of the alarm, as specified by the agent that generated it.ro TsdimAlmSeverity (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.5.1.6 |
tsdimAlarmLogSpecificProbSee textual conventions. This object is only present if it was included in the alarm trap corresponding to this AlarmLog entry.ro TsdimAlmSpecProblem (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.5.1.7 |
tsdimAlarmLogTimeIndexSee textual conventions. TsdimEventTimeInt (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.5.1.11 |
opticsIMAlarmLogAdditionalTextro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.5.1.12 |
opticsIMAlarmLogAlarmTypero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.5.1.13 |
tsdimAlarmLogTimeThis optional object indicates when the alarm has been generated.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.5.1.14 |
opticsIMAlarmLogOperatorTextThis object allows for operator to insert a text associated to this alarm.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.5.1.15 |
tsdimEFDAllTrapsThis value is used as wildcard value inside tsdimEFDTrapId. OBJECT IDENTIFIER .1.3.6.1.4.1.637.54.1.1.3.1.6 |
tsdimEFDAllObjectsThis value is used as wildcard value inside tsdimEFDTrapObject. OBJECT IDENTIFIER .1.3.6.1.4.1.637.54.1.1.3.1.7 |
tsdimEFDTableThis table specifies which traps will be sent to which management system. This EFD object is locked, via administrative state, by Agent when the first manager polling timeout expires and it is deleted when the second timeout expires. SEQUENCE OF TsdimEFDEntry .1.3.6.1.4.1.637.54.1.1.3.1.8 |
tsdimEFDEntryInformation about a group of traps to be sent to a particular IP address. A new entry must have values for all attributes that do not have default values before its RowStatus column can be set to active(1). TsdimEFDEntry .1.3.6.1.4.1.637.54.1.1.3.1.8.1 |
tsdimEFDIndexA unique number identifying the table entry. Each manager has its own index associated to it. Integer32 .1.3.6.1.4.1.637.54.1.1.3.1.8.1.1 |
tsdimEFDDestThe IP address to which traps identified by this table entry should be sent.rw IpAddress .1.3.6.1.4.1.637.54.1.1.3.1.8.1.2 |
tsdimEFDTrapIdThe ID of the trap type to which this entry applies. It can be set to tsdimEFDAllTraps OID in order to identify all traps.rw OBJECT IDENTIFIER .1.3.6.1.4.1.637.54.1.1.3.1.8.1.3 |
tsdimEFDTrapObjectThe object class to which this entry applies. The special value tsdimEFDAllObjects indicates that traps of the type specified in tsdimEFDTrapId object can be generated by all object instances.rw OBJECT IDENTIFIER .1.3.6.1.4.1.637.54.1.1.3.1.8.1.4 |
tsdimEFDPortThe UDP port on the specified management system to which traps identified by this entry should be sent.rw TsdimUdpPort (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.8.1.5 |
tsdimEFDLowestForwardedSeverityThe lowest severity of traps of this type from the specified object that should be sent to this address. This object has significance only if the trap type specified has a severity associated with it.rw TsdimAlmSeverity (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.8.1.6 |
tsdimEFDIndeterminateWhen this object has the value TRUE, traps with indeterminate severity will be forwarded to the specified destination. This object has significance only if the trap type specified has a severity associated with it.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.8.1.7 |
tsdimEFDOperStatusSee textual conventions.ro TsdimOperationalState (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.8.1.9 |
tsdimEFDRowStatusThis object is used to create a new row or to delete an existing row in the table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.8.1.10 |
tsdimEFDManagerIndexA unique number identifying the manager description inside the opticsIMMgrPollingInfoTable. It will have the same value as the opticsIMMgrPollingInfoTable index columnar object.rw Integer32 .1.3.6.1.4.1.637.54.1.1.3.1.8.1.11 |
tsdimEFDIPv6DestThe IP address in the IPv6 format to which traps identified by this table entry should be sent.rw InetAddressIPv6 .1.3.6.1.4.1.637.54.1.1.3.1.8.1.12 |
tsdimEventObjectClassIdentifierSee textual conventions.ro TsdimObjectClassId (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.9 |
tsdimEventObjectInstanceIdentifierSee textual conventions.ro TsdimObjectInstanceId (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.10 |
tsdimEventNotificationIdSee textual conventions.ro TsdimNotificationId (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.11 |
tsdimEventTimeSee textual conventions.ro TsdimEventTimeInt (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.12 |
tsdimAlarmSeveritySee textual conventions.ro TsdimAlmSeverity (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.13 |
tsdimAlarmSpecProblemSee textual conventions.ro TsdimAlmSpecProblem (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.14 |
tsdimObjectCreationNotificationIndicates a generic Object Creation Event NOTIFICATION-TYPE .1.3.6.1.4.1.637.54.1.1.3.1.18 |
tsdimObjectDeletionNotificationIndicates a generic Object Deletion Event NOTIFICATION-TYPE .1.3.6.1.4.1.637.54.1.1.3.1.19 |
tsdimAVCNotificationIndicates a generic Attribute Value Change Event NOTIFICATION-TYPE .1.3.6.1.4.1.637.54.1.1.3.1.20 |
tsdimStateChangeNotificationIndicates a generic State Change Event NOTIFICATION-TYPE .1.3.6.1.4.1.637.54.1.1.3.1.21 |
tsdimAlertNotificationIndicates an alert notification used by Agent to highlight to the managing systems the creation of new events. The Agent itself (as sysORTable) emits this notification. NOTIFICATION-TYPE .1.3.6.1.4.1.637.54.1.1.3.1.22 |
tsdimAlertNotifTimeOutThis is the alert notification time-out value. It is used by SNMP Agent in order to send the alert notification trap each time this time-out expirerw Integer32 UNITS "seconds" .1.3.6.1.4.1.637.54.1.1.3.1.23 |
tsdimAlertNotifFreqCountThis is the alert notification frequency counter value, where frequency is the number of events the SNMP Agent will generate before the creation of an alert notification trap.rw Integer32 .1.3.6.1.4.1.637.54.1.1.3.1.24 |
tsdimAlarmSevDefaultThe default severity value used for new profile index/trap ID pairs that have not yet been modified. This value is also used whenever an object's alarm severity profile index is set to 0. The default value of this object is indeterminate(5).rw TsdimAlmSeverity (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.26 |
tsdimAlarmSevProfileIndexNextThis object contains an appropriate value to be used for tsdimAlarmSevProfileIndex when creating entries in the tsdimAlarmSevProfileTable. The value -1 indicates that no unassigned entries are available. To obtain the index value for a new entry, the manager issues a management protocol retrieval operation to obtain the current value of this object. After each retrieval, the agent should modify the value to the next unassigned index (or -1).ro Integer32 .1.3.6.1.4.1.637.54.1.1.3.1.27 |
tsdimAlarmSevProfileTableThis table specifies which profiles exist. Deleting an entry in this table automatically deletes the corresponding entries in the tsdimAlarmSeverityTable. SEQUENCE OF TsdimAlarmSevProfileEntry .1.3.6.1.4.1.637.54.1.1.3.1.28 |
tsdimAlarmSevProfileEntryA group of severities, one for each alarm type in the communications alarm group. TsdimAlarmSevProfileEntry .1.3.6.1.4.1.637.54.1.1.3.1.28.1 |
tsdimAlarmSevProfileIndexA number identifying this alarm severity profile. Integer32 .1.3.6.1.4.1.637.54.1.1.3.1.28.1.1 |
tsdimAlarmSevProfileRowStatusThis object is used to create a new row or to delete an existing row in the table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.28.1.2 |
tsdimAlarmSevProfileUserLabelSee Textual Convention.rw OpticsIMUserLabel (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.28.1.3 |
tsdimAlarmSevTableThis table associates profile index and trap ID pairs with severities to be used for alarm traps that have occurred. (Note that this table does not apply to cleared alarms.) SEQUENCE OF TsdimAlarmSevEntry .1.3.6.1.4.1.637.54.1.1.3.1.29 |
tsdimAlarmSevEntryAn entry in this table associates an alarm severity profile index/trap ID pair with a severity. Deleting a particular profile's row in the alarm severity profile table deletes all rows in this table with the same profile index. TsdimAlarmSevEntry .1.3.6.1.4.1.637.54.1.1.3.1.29.1 |
tsdimAlarmSevTrapIdThe ID of the trap type to which this entry applies. OBJECT IDENTIFIER .1.3.6.1.4.1.637.54.1.1.3.1.29.1.1 |
tsdimAlarmSevSeverityThe severity to be used for this trap type when the TrapId is selected. When the agent supports the evaluation of alarm service dependency (not service affecting/service affecting), this object provides the alarm severity when it is evaluated service affecting. Otherwise this object provides the generic severity. If no value for this object has ever been set since the corresponding profile was created, the agent should return the value of the object tsdimAlarmSevDefault.rw TsdimAlmSeverity (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.29.1.2 |
tsdimAlarmSevRowStatusThis object is used to create a new row or to delete an existing row in the table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.29.1.3 |
tsdimAlarmSevSeverityNotServAffThe severity to be used for this trap type when the TrapId is selected and the agent evaluates the alarm not Service Affecting. If no value for this object has ever been set since the corresponding profile was created, the agent should return the value of the object tsdimAlarmSevDefault.rw TsdimAlmSeverity (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.29.1.4 |
tsdimAlarmSevProbableCauseThe readable format of the trap type to which this entry appliesro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.29.1.5 |
opticsIMBackupFilenameThis attribute indicates name of the backup file.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.30 |
opticsIMBackupRequestorAddressThis attribute indicates the address of the manager that has requested the operation. I will be used by the agent to provide checks to avoid multi backup operations. It is a unique number identifying the manager description inside the opticsIMMgrPollingInfoTable. It will have the same value as the opticsIMMgrPollingInfoTable index columnar object.rw Integer32 .1.3.6.1.4.1.637.54.1.1.3.1.31 |
opticsIMRestoreFilenameThis attribute indicates the name of the chosen backup file.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.32 |
opticsIMRestoreSWVersionThis attribute indicates the software version of the NE that has generated the file to backup.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.33 |
opticsIMRestoreStateThis attribute can have one of the following values: - absent(0) -- meaning not present - downloading(1) -- download in progress - present(2) -- download finished, the file is ready to apply - apply(3) -- file applied. These are used to trace the download phase. Other values: - failed (4) -- meaning a generic fail - fileNotPresent (5) -- meaning the file to restore is not present - fileNotCorrect (6) -- meaning the file to restore is not correctrw Enumeration .1.3.6.1.4.1.637.54.1.1.3.1.34 |
opticsIMRestoreRequestorAddressThis attribute indicates the address of the manager that has requested the operation. I will be used by the agent to provide checks to avoid multi restore operations. It is a unique number identifying the manager description inside the opticsIMMgrPollingInfoTable. It will have the same value as the opticsIMMgrPollingInfoTable index columnar object.rw Integer32 .1.3.6.1.4.1.637.54.1.1.3.1.35 |
tsdimRowChangeNotificationIndicates a Row Change Event NOTIFICATION-TYPE .1.3.6.1.4.1.637.54.1.1.3.1.36 |
tsdimGenEventLogTableThis table contain information about single generic event notification. Entries in this table are created automatically by Agent and they are never deleted because the Log behavior is automatically set to Wrap, hence when no more entry will be created (log full) new log entry will cause the deletion of the oldest one. The objects tsdimGenEventLogObj* form a static array of generic objects. When a Generic Event Notification is sent, all its objects are mapped in an entry of this table. The first five objects, called common objects, of this table have the same name and type of the corresponding Generic Event Notification. The remaining tsdimGenEventLogObj* are particular: they form a static array of generic objects; each of these object represent a specific object of the corresponding Generic Event Notification. Each object of the Generic Event Notification, with the exception of the common ones, is translated to an OCTET STRING form and then copied in the relative tsdimGenEventLogObj* following the Object Identifier order. SEQUENCE OF TsdimGenEventLogEntry .1.3.6.1.4.1.637.54.1.1.3.1.37 |
tsdimGenEventLogEntryAn entry in the tsdimGenEventLogTable TsdimGenEventLogEntry .1.3.6.1.4.1.637.54.1.1.3.1.37.1 |
tsdimGenEventLogEventTypeThis object describes the type of the generic event logged.ro Enumeration .1.3.6.1.4.1.637.54.1.1.3.1.37.1.1 |
tsdimGenEventLogObjectClassIdentifierSee textual conventions.ro TsdimObjectClassId (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.37.1.2 |
tsdimGenEventLogObjectInstanceIdentifierSee textual conventions.ro TsdimObjectInstanceId (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.37.1.3 |
tsdimGenEventLogNotificationIdSee textual conventions. TsdimNotificationId (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.37.1.4 |
tsdimGenEventLogEventTimeIndexSee textual conventions. TsdimEventTimeInt (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.37.1.5 |
tsdimGenEventLogObj1See textual conventions.ro GenEventLogObj (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.37.1.6 |
tsdimGenEventLogObj2See textual conventions.ro GenEventLogObj (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.37.1.7 |
tsdimGenEventLogObj3See textual conventions.ro GenEventLogObj (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.37.1.8 |
tsdimGenEventLogObj4See textual conventions.ro GenEventLogObj (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.37.1.9 |
tsdimGenEventLogObj5See textual conventions.ro GenEventLogObj (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.37.1.10 |
tsdimGenEventLogObj6See textual conventions.ro GenEventLogObj (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.37.1.11 |
tsdimGenEventLogObj7See textual conventions.ro GenEventLogObj (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.37.1.12 |
tsdimGenEventLogObj8See textual conventions.ro GenEventLogObj (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.37.1.13 |
tsdimGenEventLogObj9See textual conventions.ro GenEventLogObj (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.37.1.14 |
tsdimGenEventLogObj10See textual conventions.ro GenEventLogObj (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.37.1.15 |
opticsIMProtectionSwitchReportingIndicates a generic protection switch event. The object class identifies the type of protection unit. Both the involved object instances are included in the notification. NOTIFICATION-TYPE .1.3.6.1.4.1.637.54.1.1.3.1.38 |
opticsIMEFDAllEventsThis value is used as events, not alarms, wildcard value inside tsdimEFDTrapId. OBJECT IDENTIFIER .1.3.6.1.4.1.637.54.1.1.3.1.39 |
opticsIMSwPackageTableThis table contains the information on the software packages present in the equipment. SEQUENCE OF OpticsIMSwPackageEntry .1.3.6.1.4.1.637.54.1.1.3.1.40 |
opticsIMSwPackageEntryAn entry of the opticsIMSwPackageTable. Each entry represents a network element software release. It is created, by the managed system during the commissioning phase or as a result of a download operation. OpticsIMSwPackageEntry .1.3.6.1.4.1.637.54.1.1.3.1.40.1 |
opticsIMSwPackageIndexThis object represents the index of the table. Integer32 .1.3.6.1.4.1.637.54.1.1.3.1.40.1.1 |
opticsIMSwPackageCommandThis object is used to activate a stand-by version or to commit an activated one. As consequence of an activation command, the stand-by software package addressed by the command becomes active and, viceversa,the active one becomes a stand-by version or a boot one according to the previous state of the software package (active or comitted, respectively). If the forced activation is required, the stand-by software version is activated also if it is the same as the active one. The manager can read the result of the activation (forced or not) in the SwPackageActivationResult object. The commit command is used to indicate that the active version has to be used as the bootstrap software in case of re-start. This command can be addressed only on an active version. In some NEs the commit command is not supported and the commitment of the activated version takes place implicitely together with the activation itself, so that in case of restart events the version used for rebooting is the active version. When the activation or commit command has been completed, the agent has to change the value back to 'none'.rw Enumeration .1.3.6.1.4.1.637.54.1.1.3.1.40.1.2 |
opticsIMSwPackageActivationResultThis object represents the result of a software package activation (forced or not).ro Enumeration .1.3.6.1.4.1.637.54.1.1.3.1.40.1.3 |
opticsIMSwPackageActivationDateThis object indicates the date and time of the last activation of the software package.It is provided according to the following format:yyyy/mm/dd hh:mm:ss. If the software package has not been yet activated, the string notYetActivated is used.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.40.1.4 |
opticsIMSwPackageCurrentStateThis object represents the current state of the software package.ro Enumeration .1.3.6.1.4.1.637.54.1.1.3.1.40.1.5 |
opticsIMSwPackageLabelThis object specifies the name of the software package.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.40.1.6 |
opticsIMSwPackageVersionThis object specifies the version of the software package (i.e. V02.11.00).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.40.1.7 |
opticsIMSwPackageOperationalStateSee textual conventions. It defines if the software package is correctly loaded (enabled) or not (disabled).ro TsdimOperationalState (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.40.1.8 |
opticsIMSwPackageReleaseThis object specifies the version of the software package (i.e. V02.11.00).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.40.1.9 |
opticsIMSwUnitTableThis table contains the information on the software units present in the software package. SEQUENCE OF OpticsIMSwUnitEntry .1.3.6.1.4.1.637.54.1.1.3.1.41 |
opticsIMSwUnitEntryAn entry of the opticsIMSwUnitTable. OpticsIMSwUnitEntry .1.3.6.1.4.1.637.54.1.1.3.1.41.1 |
opticsIMSwUnitIndexThis object represents the index of the software unit table. Integer32 .1.3.6.1.4.1.637.54.1.1.3.1.41.1.1 |
opticsIMSwUnitLabelThis object specifies the name of the software unit (i.e EC).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.41.1.2 |
opticsIMSwUnitVersionThis object specifies the version of the software unit (i.e. V01.03.10).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.41.1.3 |
opticsIMSwUnitSizeThis object specifies the size of the software unit in bytes.ro Integer32 UNITS "bytes" .1.3.6.1.4.1.637.54.1.1.3.1.41.1.4 |
opticsIMswdlStatusIndicatorSee textual conventions.ro OpticsIMSwdlStatusIndicator (OPTICSIM-COMMON-TC) .1.3.6.1.4.1.637.54.1.1.3.1.42 |
opticsIMSwdlInitTableThis table contains information about software download Initialization phase. SEQUENCE OF OpticsIMSwdlInitEntry .1.3.6.1.4.1.637.54.1.1.3.1.48 |
opticsIMSwdlInitEntryAn entry in the opticsIMSwdlInitTable. OpticsIMSwdlInitEntry .1.3.6.1.4.1.637.54.1.1.3.1.48.1 |
opticsImSwdlInitTableIndexThis object defines the index of the table. Integer32 .1.3.6.1.4.1.637.54.1.1.3.1.48.1.1 |
opticsImSwdlInitForcedDownloadThis flag indicates whether the version indicated by the identifier of the new software release has to be loaded entirely regardless of the fact that some software units may already be present in the NE.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.48.1.2 |
opticsImSwdlInitSwPkgVersionThis object contains the version of the new SW Release to be delivered to the managed system.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.48.1.3 |
opticsImSwdlInitSwPkgLabelThis object contains the Label of the new SW Release to be delivered to the managed system.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.48.1.4 |
opticsImSwdlInitDescrNameThis object contains the Name of the Description file to be delivered to the managed system.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.48.1.5 |
opticsIMSwdlInitRowStatusThis object is used to create / delete a row. Delete is used to abort Software download Operation. When a new row is created the opticsIMswdlStatusIndicator is changed in Downloading, when the row is deleted the Swdl operation is aborted or finished and the opticsIMswdlStatusIndicator is changed in Idle.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.48.1.6 |
opticsIMNERestartRequestThis object is used to require the execution of the restart procedure on the NE. On the reception of this request, the agent will execute the committed software version, in the same way of a spontaneous restart. When the restart has been completed, the agent has to change the value back to 'idle' and set the restart flag (opticsIMInfoNERestartFlag attribute of the opticsIMInfoPolledTable). Note: the restart(1) value should be used if there is no distinction between cold and warm restart. If there is a distinction, then the correct value i.e. coldRestart(3) or warmRestart(3) should be used, as appropriate. dbTruncate option commands the Agent to 'shrink' the DB and automatically perform a coldRestart.rw Enumeration .1.3.6.1.4.1.637.54.1.1.3.1.54 |
opticsIMBackupStateThis attribute is used to trace the backup phase.rw Enumeration .1.3.6.1.4.1.637.54.1.1.3.1.55 |
opticsIMEqptSwUnitTableThis table contains the information on the software units present in the equipment. SEQUENCE OF OpticsIMEqptSwUnitEntry .1.3.6.1.4.1.637.54.1.1.3.1.56 |
opticsIMEqptSwUnitEntryAn entry of the opticsIMEqptSwUnitTable. OpticsIMEqptSwUnitEntry .1.3.6.1.4.1.637.54.1.1.3.1.56.1 |
opticsIMEqptSwUnitPositionThis object represents the index of the equipment software unit table. OCTET STRING .1.3.6.1.4.1.637.54.1.1.3.1.56.1.1 |
opticsIMEqptSwUnitLabelThis object specifies the name of the software unit (i.e EC).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.56.1.2 |
opticsIMEqptSwUnitVersionThis object specifies the version of the software unit (i.e. V01.03.10).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.56.1.3 |
opticsIMEqptSwUnitSwdlStatusThis object specifies the status of the download of the software unit.ro Enumeration .1.3.6.1.4.1.637.54.1.1.3.1.56.1.4 |
tsdimEFDAllAlarmsThis value is used as alarms, not generic events, wildcard value inside tsdimEFDTrapObject. OBJECT IDENTIFIER .1.3.6.1.4.1.637.54.1.1.3.1.57 |
opticsIMAutoDiscoveryStatusThe autoDiscoveryStatus indicates the current status of auto-discovery can be: - idle (default): auto-discovery not enabled. - auto-discovery ongoing: in this status the auto-discovery has been enabled, but no response message has been received from network management. - auto-discovery succeeded: the auto-discovery succeeded. This status represents the receiving of the Acknowledge response from OS - auto-discovery failed: the auto-discovery failed. This status represents the receiving of'Nack' message from OS.ro Enumeration .1.3.6.1.4.1.637.54.1.1.3.1.58 |
opticsIMEnableAutodiscoveryThis object is used to activate and stop the auto-discovery mechanism in the NE. It is possible to use the same action with different syntax: - if activation is selected (enabled): once accepted this action, the NE starts sending the auto-discovery message to the network management system. The status reported in the autodiscoveryStatus attribute goes to ongoing. The action is refused if either the local address or the network management address has not been configured. - if stop is selected (disable): the auto-discovery mechanism is stopped. This option is always accepted and the status (reported in the autodiscoveryStatus object) comes back to idle.rw Enumeration .1.3.6.1.4.1.637.54.1.1.3.1.59 |
opticsimSnmpMainOSIpAddressThis objects defines the IP address of the main OS. The default value is 0.0.0.0 (no IP address configured)rw IpAddress .1.3.6.1.4.1.637.54.1.1.3.1.60 |
opticsimSnmpMainOSUdpPortThis objects defines the UDP port of the main OS.rw TsdimUdpPort (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.61 |
opticsimSnmpSpareOSIpAddressThis objects defines the IP address of the spare OS. The default value is 0.0.0.0 (no IP address configured)rw IpAddress .1.3.6.1.4.1.637.54.1.1.3.1.62 |
opticsimSnmpSpareOSUdpPortThis objects defines the UDP port of the spare OS.rw TsdimUdpPort (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.63 |
opticsIMAdditionalTextThis optional object indicates when the alarm has been generated.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.64 |
opticsIMAlarmTypeThis optional object indicates when the alarm has been generated.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.65 |
tsdimSupportMibObjBackupServ OBJECT IDENTIFIER .1.3.6.1.4.1.637.54.1.1.3.1.66 |
opticsImBackupServerAddressThis object contains the Address of the Backup Server. This information is used by the Backup Client to connect the server.rw IpAddress .1.3.6.1.4.1.637.54.1.1.3.1.66.1 |
opticsImBackupServerPortThis object contains the Port of the BACKUP Server. This information is used by the BACKUP Client to connect the BACKUP server.rw Integer32 .1.3.6.1.4.1.637.54.1.1.3.1.66.2 |
opticsImBackupServerUserIdThis object contains the UserId of BACKUP Server. This information is used by the BACKUP Client to connect the BACKUP server.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.66.3 |
opticsImBackupServerPasswordThis object contains the Password of Backup Server. This information is used by the BACKUP Client to connect the BACKUP server.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.66.4 |
opticsImBackupServerRootDirThis object contains the Root Directory of Backup Server. This information is used by the BACKUP Client to connect the BACKUP server.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.66.5 |
opticsImBackupServerIPv6AddressThis object contains the Address in IPv6 format of the Backup Server. This information is used by the Backup Client to connect the server.rw InetAddressIPv6 .1.3.6.1.4.1.637.54.1.1.3.1.66.6 |
tsdimSupportMibObjRestoreServ OBJECT IDENTIFIER .1.3.6.1.4.1.637.54.1.1.3.1.67 |
opticsImRestoreServerAddressThis object contains the Address of the RESTORE Server. This information is used by the RESTORE Client to connect the RESTORE server.rw IpAddress .1.3.6.1.4.1.637.54.1.1.3.1.67.1 |
opticsImRestoreServerPortThis object contains the Port of the RESTORE Server. This information is used by the RESTORE Client to connect the RESTORE server.rw Integer32 .1.3.6.1.4.1.637.54.1.1.3.1.67.2 |
opticsImRestoreServerUserIdThis object contains the UserId of RESTORE Server. This information is used by the RESTORE Client to connect the RESTORE server.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.67.3 |
opticsImRestoreServerPasswordThis object contains the Password of Restore Server. This information is used by the RESTORE Client to connect the RESTORE server.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.67.4 |
opticsImRestoreServerRootDirThis object contains the Root Directory of Restore Server. This information is used by the RESTORE Client to connect the RESTORE server.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.67.5 |
opticsImRestoreServerIPv6AddressThis object contains the Address in IPv6 format of the RESTORE Server. This information is used by the RESTORE Client to connect the RESTORE server.rw InetAddressIPv6 .1.3.6.1.4.1.637.54.1.1.3.1.67.6 |
tsdimSupportMibObjRestoreOp OBJECT IDENTIFIER .1.3.6.1.4.1.637.54.1.1.3.1.68 |
opticsIMRestorePercentageThis object contains the percentage of Restore file(s) transferred. This value is used by the managing System to poll RESTORE information.ro INTEGER .1.3.6.1.4.1.637.54.1.1.3.1.68.1 |
opticsIMRestoreTotalBytesThis object contains the total number of bytes of Restore file(s) transferred. This value is used by the managing System to poll RESTORE information.ro INTEGER .1.3.6.1.4.1.637.54.1.1.3.1.68.2 |
opticsIMRestoreCurrentFileThis object contains the name of the File in transfer. This value is used by the managing System to poll RESTORE information.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.68.3 |
tsdimSupportMibObjPMCollectionServ OBJECT IDENTIFIER .1.3.6.1.4.1.637.54.1.1.3.1.69 |
opticsImPMCollectionServerAddressThis object contains the Address of the PM collection Server. This information is used by the PM collection Client to connect the PM collection server.rw IpAddress .1.3.6.1.4.1.637.54.1.1.3.1.69.1 |
opticsImPMCollectionServerPortThis object contains the Port of the PM collection Server. This information is used by the PM collection Client to connect the PM collection server.rw Integer32 .1.3.6.1.4.1.637.54.1.1.3.1.69.2 |
opticsImPMCollectionServerUserIdThis object contains the UserId of PM collection Server. This information is used by the PM collection Client to connect the PM collection server.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.69.3 |
opticsImPMCollectionServerPasswordThis object contains the Password of PM collection Server. This information is used by the PM collection Client to connect the PM collection server.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.69.4 |
opticsImPMCollectionServerRootDirThis object contains the Root Directory of PM collection Server. This information is used by the PM collection Client to connect the PM collection server.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.69.5 |
tsdimSupportMibObjMACAddressCollectionServ OBJECT IDENTIFIER .1.3.6.1.4.1.637.54.1.1.3.1.70 |
opticsImMACAddressCollectionServerAddressThis object contains the Address of the Server. This information is used by the MAC Address Collection Client to connect the MAC Address Collection server.rw IpAddress .1.3.6.1.4.1.637.54.1.1.3.1.70.1 |
opticsImMACAddressCollectionServerPortThis object contains the Port of the MAC Address Collection Server. This information is used by the MAC Address Collection Client to connect the MAC Address Collection server.rw Integer32 .1.3.6.1.4.1.637.54.1.1.3.1.70.2 |
opticsImMACAddressCollectionServerUserIdThis object contains the UserId of MAC Address Collection Server. This information is used by the MAC Address Collection Client to connect the MAC Address Collection server.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.70.3 |
opticsImMACAddressCollectionServerPasswordThis object contains the Password of MAC Address Collection Server. This information is used by the MAC Address Collection Client to connect the MAC Address Collection server.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.70.4 |
opticsImMACAddressCollectionServerRootDirThis object contains the Root Directory of MAC Address Collection Server. This information is used by the MAC Address Collection Client to connect the MAC Address Collection server.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.70.5 |
opticsImFileTrasferProtocolsCapabilityA value that uniquely identifies the set of supported file transfer protocols.ro OpticImFileTrasferProtocolList (OPTICSIM-COMMON-TC) .1.3.6.1.4.1.637.54.1.1.3.1.71 |
opticsImFileTrasferProtocolConfiguredA value that allows the configuration of the file transfer protocol used by the NE. It is possible to set to 1 only a single bit of the bit mask (i.e. the NE accepts the configuration of only one file transfer protocol). The default value is NE type dependent.rw OpticImFileTrasferProtocolList (OPTICSIM-COMMON-TC) .1.3.6.1.4.1.637.54.1.1.3.1.72 |
tsdimSupportMibObjUalUploadServ OBJECT IDENTIFIER .1.3.6.1.4.1.637.54.1.1.3.1.73 |
opticsImUalUploadServerAddressThis object contains the Address of the UAL Upload Server. This information is used by the UAL Upload Client to connect the server.rw IpAddress .1.3.6.1.4.1.637.54.1.1.3.1.73.1 |
opticsImUalUploadServerPortThis object contains the Port of the UAL Upload Server. This information is used by the UAL Upload Client to connect the UAL Upload server.rw Integer32 .1.3.6.1.4.1.637.54.1.1.3.1.73.2 |
opticsImUalUploadServerUserIdThis object contains the UserId of UAL Upload Server. This information is used by the UAL Upload Client to connect the UAL Upload server.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.73.3 |
opticsImUalUploadServerPasswordThis object contains the Password of UAL Upload Server. This information is used by the UAL Upload Client to connect the server.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.73.4 |
opticsImUalUploadServerRootDirThis object contains the Root Directory of UAL Upload Server. This information is used by the UAL Upload Client to connect the server.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.73.5 |
opticsIMUalUploadFilenameThis attribute indicates name of the UAL upload file.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.73.6 |
opticsIMUalUploadRequestorAddressThis attribute indicates the address of the manager that has requested the operation. I will be used by the agent to provide checks to avoid multi upload operations. It is a unique number identifying the manager description inside the opticsIMMgrPollingInfoTable. It will have the same value as the opticsIMMgrPollingInfoTable index columnar object.rw Integer32 .1.3.6.1.4.1.637.54.1.1.3.1.73.7 |
opticsIMUalUploadStateThis attribute is used to trace the upload phase.rw Enumeration .1.3.6.1.4.1.637.54.1.1.3.1.73.8 |
opticsImSecureLogUploadTransferProtocolHostKeyThis object contains the host key of the UAL Upload Server. This information is used by the UAL Upload Client to connect the Ftp server in case secureFtp protocol (opticsIMFileTrasferProtocolType = sFtpServer ). The default value is a null string.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.73.9 |
opticsImUalUploadServerIpv6AddressThis object contains the Address of the UAL Upload Server in Ipv6 format. This information is used by the UAL Upload Client to connect the server.rw InetAddressIPv6 .1.3.6.1.4.1.637.54.1.1.3.1.73.10 |
tsdimSupportMibObjUalConfiguration OBJECT IDENTIFIER .1.3.6.1.4.1.637.54.1.1.3.1.74 |
opticsImUalLogFileSizeThis object indicates size of UAL log file , in KiloByte blocks.ro Integer32 .1.3.6.1.4.1.637.54.1.1.3.1.74.1 |
opticsImUalLogEvent OBJECT IDENTIFIER .1.3.6.1.4.1.637.54.1.1.3.1.74.2 |
opticsImUalSECULogThis object is used to enable/disable SECU (security) events log , the default value is enabled .rw Enumeration .1.3.6.1.4.1.637.54.1.1.3.1.74.2.1 |
opticsImUalCOMMLogThis object is used to enable/disable COMM (communication & routing) events log , the default value is enabled .rw Enumeration .1.3.6.1.4.1.637.54.1.1.3.1.74.2.2 |
opticsImUalEQPTLogThis object is used to enable/disable EQPT (equipment) events log , the default value is enabled .rw Enumeration .1.3.6.1.4.1.637.54.1.1.3.1.74.2.3 |
opticsImUalDATALogThis object is used to enable/disable DATA (Ethernet Provision) events log , the default value is enabled .rw Enumeration .1.3.6.1.4.1.637.54.1.1.3.1.74.2.4 |
opticsIMEFDExtensionTableThis table associate some extra parameters to the EFDtable to be used to send traps to a particular IP Address. SEQUENCE OF OpticsIMEFDExtensionEntry .1.3.6.1.4.1.637.54.1.1.3.1.75 |
opticsIMEFDExtensionEntryExtra information about a group of traps to be sent to a particular IP address, over the information already defined on tsdimEFDtable. OpticsIMEFDExtensionEntry .1.3.6.1.4.1.637.54.1.1.3.1.75.1 |
opticsIMEFDUserNameThe username for the SNMPv3 traps identified by this table entry should be sent.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.75.1.1 |
opticsImLicenseCodeThis object allows to update by managing system the LicenseString that identifies the features bought by the customer.rw OCTET STRING .1.3.6.1.4.1.637.54.1.1.3.1.100 |
opticsImSwLicenseThis object allows to report in a clear text to the managing system the list of Licenses that identify the features bougth by the customer.ro OCTET STRING .1.3.6.1.4.1.637.54.1.1.3.1.101 |
opticsImLedsResetThis object is used to trigger a reset of all the Leds present on equipment. As consequence, all the Leds are cleared and the opticsImAttendedStatus objects is set to 'on' value. When the reset has been completed, the agent has to change the value of opticsImLedsReset object back to notResetting.rw Enumeration .1.3.6.1.4.1.637.54.1.1.3.1.105 |
opticsImAttendedStatusThis object specifies the status of the Leds Reset procedure (on or off). When the opticsImLedsReset object is set to 'resetting' value the agent has to set this object (opticsImAttendedStatus ) to 'on' value, clear all the Leds present on equipment, and store the list of raised alarms (that highlighted on Leds to clear). When all the alarms present on stored list are cleared, the agent has to change the value of opticsImAttendedStatus object to 'off' value.ro Enumeration .1.3.6.1.4.1.637.54.1.1.3.1.106 |
opticsIMTelnetStatusThis object is used to enable/disable telnet service, the default value is enabledrw Enumeration .1.3.6.1.4.1.637.54.1.1.3.1.107 |
opticsIMSftpStatusThis object is used to enable/disable Sftp service, the default value is enabledrw Enumeration .1.3.6.1.4.1.637.54.1.1.3.1.108 |
opticsIMNeLongitudeThis object contains the real number describing the longitude encoded as a printable string. The precision is limited by 32 characters within the range -90..90 degrees. Positive numbers indicate locations north of the equator. The value is encoded as strings as to avoid the precision limitations imposed by encoding as unsigned integers. Although this might not be considered optimal, it allows for a very high degree of precision with an acceptable average encoded record length.rw DisplayString .1.3.6.1.4.1.637.54.1.1.3.1.110 |
opticsIMNeLatitudeThis object contains the real number describing the latitude encoded as a printable string. The precision is limited by 32 characters within the range -180..180 degrees. Positive numbers indicate locations east of the prime meridian. The value is encoded as strings as to avoid the precision limitations imposed by encoding as unsigned integers. Although this might not be considered optimal, it allows for a very high degree of precision with an acceptable average encoded record length.rw DisplayString .1.3.6.1.4.1.637.54.1.1.3.1.111 |
opticsIMNeHttpServerPortThis object contains the Port of the HTTP Server hosted on the NE. This information is used by the HTTP Client to connect the HTTPserver.rw Integer32 .1.3.6.1.4.1.637.54.1.1.3.1.112 |
opticsIMHttpsStatusThis object is used to enable/disable HTTPS service for remote and local access, the default value is disabled.rw Enumeration .1.3.6.1.4.1.637.54.1.1.3.1.113 |
opticsIMNeAltitudeThis object contains the real number describing the altitude (height from a reference 0 value) encoded as a printable string. The precision is limited by 32 characters within the range 0..5000 meters (the mesusre unit). The value is encoded as strings as to avoid the precision limitations imposed by encoding as unsigned integers. Although this might not be considered optimal, it allows for a very high degree of precision with an acceptable average encoded record length.rw DisplayString .1.3.6.1.4.1.637.54.1.1.3.1.114 |
opticsIMAlarmsSeveritySummaryTableThis table gives the number of alarms currently raised in the node per each severity level. SEQUENCE OF OpticsIMAlarmsSeveritySummaryEntry .1.3.6.1.4.1.637.54.1.1.3.1.115 |
opticsIMAlarmsSeveritySummaryEntryInformation about he number of alarms currently raised in the node per severity level. Entries in this table are created by the node at start-up. OpticsIMAlarmsSeveritySummaryEntry .1.3.6.1.4.1.637.54.1.1.3.1.115.1 |
opticsIMAlarmsSeveritySummaryIndexSee textual conventions. TsdimAPTAlmSeverity (TSDIM-SNMP-TC) .1.3.6.1.4.1.637.54.1.1.3.1.115.1.1 |
opticsIMAlarmsSeveritySummaryTotalTotal number of alarms currently raaised for this severity level.ro Integer32 .1.3.6.1.4.1.637.54.1.1.3.1.115.1.2 |
tsdimSupportMibObjSwdlServ OBJECT IDENTIFIER .1.3.6.1.4.1.637.54.1.1.3.1.500 |
opticsImSwdlServerAddressThis object contains the Address of the SWDL Server. This information is used by the SWDL Client to connect the SWDL server.rw IpAddress .1.3.6.1.4.1.637.54.1.1.3.1.500.1 |
opticsImSwdlServerPortThis object contains the Port of the SWDL Server. This information is used by the SWDL Client to connect the SWDL server.rw Integer32 .1.3.6.1.4.1.637.54.1.1.3.1.500.2 |
opticsImSwdlServerUserIdThis object contains the UserId of SWDL Server. This information is used by the SWDL Client to connect the SWDL server.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.500.3 |
opticsImSwdlServerPasswordThis object contains the Password of Swdl Server. This information is used by the SWDL Client to connect the SWDL server.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.500.4 |
opticsImSwdlServerRootDirThis object contains the Root Directory of Swdl Server. This information is used by the SWDL Client to connect the SWDL server.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.500.5 |
opticsImSwdlServerIPv6AddressThis object contains the Address of the SWDL Server in the IPv6 format. This information is used by the SWDL Client to connect the SWDL server.rw InetAddressIPv6 .1.3.6.1.4.1.637.54.1.1.3.1.500.6 |
tsdimSupportMibObjSwdlOp OBJECT IDENTIFIER .1.3.6.1.4.1.637.54.1.1.3.1.515 |
opticsIMSwdlPercentageThis object contains the percentage of SW Package transferred. This value is used by the managing System to poll SWDL information.ro INTEGER .1.3.6.1.4.1.637.54.1.1.3.1.515.1 |
opticsIMSwdlTotalBytesThis object contains the total number of bytes of SW Package transferred. This value is used by the managing System to poll SWDL information.ro INTEGER .1.3.6.1.4.1.637.54.1.1.3.1.515.2 |
opticsIMSwdlCurrentSwUnitVersionThis object contains the Version of the SW Unit in transfer. This value is used by the managing System to poll SWDL information.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.515.3 |
opticsIMSwdlCurrentSwUnitLabelThis object contains the Label of the SW Unit in transfer. This value is used by the managing System to poll SWDL information.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.515.4 |
opticsImSwdlResultThis object contains the Result of Software Download operation. This value is used by the managing System to poll SWDL information. When Software Downwload is in progress opticsImSwdlResult takes the value underDownloading, otherwise it reports the Result of Software Download operation.ro Enumeration .1.3.6.1.4.1.637.54.1.1.3.1.515.5 |
opticsImSwdlServerTrasferProtocolTypeThis object contains the type of Transfer Protocol of the SWDL Server. This information is used by the NE to use the correct SWDL Client type to connect the SWDL server.rw Enumeration .1.3.6.1.4.1.637.54.1.1.3.1.515.6 |
opticsImSwdlServerSecureTrasferProtocolHostKeyThis object contains the host key of the SWDL Server. This information is used by the SWDL Client type to connect the SWDL server in case sFtp protocol (opticsImSwdlServerTrasferProtocolType = sFerverFtp). The default value is a null string.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.515.7 |
xhaulSwdlSwNextFileThis attribute indicates the name of the next file to be transferred to the node for Sw Download.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.515.8 |
xhaulSwdlSwProcessFileThis attribute indicates that the file for Sw Download has been transferred to the node and ready to be taken into account.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.515.9 |
opticsIMSupportMibObjAbnCond OBJECT IDENTIFIER .1.3.6.1.4.1.637.54.1.1.3.1.530 |
opticsIMActiveAbnCondThis object specifies whether at least one abnormal condition is present in the NE (TRUE).ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.530.1 |
opticsIMAbnCondAffectedObjectsListTableThis table contains the list of objects affected by an abnormal condition. SEQUENCE OF OpticsIMAbnCondAffectedObjectsListEntry .1.3.6.1.4.1.637.54.1.1.3.1.530.2 |
opticsIMAbnCondAffectedObjectsListEntryAn entry of the abnormal condition affected object list table. OpticsIMAbnCondAffectedObjectsListEntry .1.3.6.1.4.1.637.54.1.1.3.1.530.2.1 |
opticsIMAbnCondAffectedObjectsListIndexThis object represents the index of the table. Integer32 .1.3.6.1.4.1.637.54.1.1.3.1.530.2.1.1 |
opticsIMAbnCondAffectedObjectInstanceIdThis object represents the instance identifier of an object affected by an abnormal condition.ro InstancePointer (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.530.2.1.2 |
opticsIMOffNormalDescriptionThis object represents the description of an abnormal (off normal) condition.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.530.2.1.3 |
opticsImManagementProtocolsCapabilityA value that uniquely identifies the set of the main supported management protocolsro Bits .1.3.6.1.4.1.637.54.1.1.3.1.1110 |
opticsIMFileTrasferProtocolTypeThis object contains the type of File Transfer Protocol to use on agent for file exchange with Server on manager side. This information is used by the NE to use the correct ftp Client type to connect the ftp server.rw Enumeration .1.3.6.1.4.1.637.54.1.1.3.1.1111 |
opticsImSecureFileTrasferProtocolHostKeyThis object contains the host key of the Ftp Server. This information is used by the Ftp Client to connect the Ftp server in case secureFtp protocol (opticsIMFileTrasferProtocolType = sFtpServer ). The default value is a null string.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.1112 |
opticsIMSupportMibObjAntiTheft OBJECT IDENTIFIER .1.3.6.1.4.1.637.54.1.1.3.1.1113 |
opticsIMAntiTheftAdminStatusThis object allows to enable/disable the Anti-Theft procedure by managing system.rw Enumeration .1.3.6.1.4.1.637.54.1.1.3.1.1113.1 |
opticsIMAntiTheftTimerExpirationThis object allows to define the timer expiration, measured in units of hours, for the Anti-Theft procedure.rw Integer32 .1.3.6.1.4.1.637.54.1.1.3.1.1113.2 |
opticsIMAntiTheftManagerKeyCodeThis object allows to update, by managing system to the device, the Network Manager Key code .rw OCTET STRING .1.3.6.1.4.1.637.54.1.1.3.1.1113.3 |
opticsIMSendKeyCodeIndicates the notification to require the managing system to send the Network Manager key code. NOTIFICATION-TYPE .1.3.6.1.4.1.637.54.1.1.3.1.1113.4 |
opticsIMSupportMibObjFileTransferServ OBJECT IDENTIFIER .1.3.6.1.4.1.637.54.1.1.3.1.1114 |
opticsIMFileTransferServerAddressThis object contains the Address of the SWDL Server. This information is used by the SWDL Client to connect the SWDL server.rw IpAddress .1.3.6.1.4.1.637.54.1.1.3.1.1114.1 |
opticsIMFileTransferServerPortThis object contains the Port of the SWDL Server. This information is used by the SWDL Client to connect the SWDL server.rw Integer32 .1.3.6.1.4.1.637.54.1.1.3.1.1114.2 |
opticsIMFileTransferServerUserIdThis object contains the UserId of SWDL Server. This information is used by the SWDL Client to connect the SWDL server.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.1114.3 |
opticsIMFileTransferServerPasswordThis object contains the Password of Swdl Server. This information is used by the SWDL Client to connect the SWDL server.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.1114.4 |
opticsIMFileTransferServerRootDirThis object contains the Root Directory of Swdl Server. This information is used by the SWDL Client to connect the SWDL server.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.1114.5 |
opticsIMFileTransferServerAddressIpv6This object contains the Address of the SWDL Server in the IPv6 format. This information is used by the SWDL Client to connect the SWDL server.rw InetAddressIPv6 .1.3.6.1.4.1.637.54.1.1.3.1.1114.6 |
opticsIMFileTransferStateThis attribute is used to trace the file transfer phase.rw Enumeration .1.3.6.1.4.1.637.54.1.1.3.1.1114.7 |
opticsIMRSLFileNameThis attribute indicates name of the RSL file to be transferred.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.1115 |
opticsIMIANDCFileNameThis attribute indicates name of the Installation and Commisioning file to be transferred.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.1116 |
opticsIMSupportMibObjPswdUpdateServ OBJECT IDENTIFIER .1.3.6.1.4.1.637.54.1.1.3.1.1117 |
opticsImPasswordUpdateFilenameThis attribute indicates the name of the file to be transferred for the password update process.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.1117.1 |
opticsImPasswordUpdateFileHashThis attribute contains the hash of the file to be transferred for the password update process.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.637.54.1.1.3.1.1117.2 |
opticsIMPasswordUpdateResultThis object represents the result of a Password Update process.ro Enumeration .1.3.6.1.4.1.637.54.1.1.3.1.1117.3 |
tsdimSupportMCConf OBJECT IDENTIFIER .1.3.6.1.4.1.637.54.1.1.99.1 |
tsdimSupportMCCompl OBJECT IDENTIFIER .1.3.6.1.4.1.637.54.1.1.99.1.1 |
tsdimSupportMcThis module compliance describes a set of objects required for TSD-IM SNMP Agent implementation. These objects are defined inside tsdimSupportMib Unknown .1.3.6.1.4.1.637.54.1.1.99.1.1.1 |
tsdimSupportMCGroup OBJECT IDENTIFIER .1.3.6.1.4.1.637.54.1.1.99.1.2 |
tsdimAlarmLogGroupThis group describes the mandatory objects needed for the Alarm Log management configuration. Unknown .1.3.6.1.4.1.637.54.1.1.99.1.2.1 |
tsdimAPTGroupThis group describes the mandatory objects needed for the APT management configuration. Unknown .1.3.6.1.4.1.637.54.1.1.99.1.2.2 |
tsdimLogMngmtGroupThis group lists objects needed for Log, both event and alarm, configuration. Unknown .1.3.6.1.4.1.637.54.1.1.99.1.2.3 |
tsdimEventLogGroupThis group describes the mandatory objects needed for the Event Log management configuration. Unknown .1.3.6.1.4.1.637.54.1.1.99.1.2.6 |
tsdimAuxEventObjectsGroupThis group describes the mandatory objects needed for the notification, both events and alarms, management. Unknown .1.3.6.1.4.1.637.54.1.1.99.1.2.7 |
tsdimOptAuxObjectsGroupThis group describes the mandatory objects needed for the notification, both events and alarms, management. Unknown .1.3.6.1.4.1.637.54.1.1.99.1.2.9 |
tsdimEventNotificationGroupThis group describes the SNMP NE notifications, not alarms. Unknown .1.3.6.1.4.1.637.54.1.1.99.1.2.10 |
tsdimAlertNotificationGroupThis group describes the SNMP NE alert notification. Unknown .1.3.6.1.4.1.637.54.1.1.99.1.2.11 |
tsdimAlertObjectGroupThis group describes the SNMP NE alert objects. Unknown .1.3.6.1.4.1.637.54.1.1.99.1.2.12 |
tsdimEFDGroupThis group describes the EFD mandatory objects. Unknown .1.3.6.1.4.1.637.54.1.1.99.1.2.13 |
tsdimOptEFDGroupThis group describes the EFD optional objects. Unknown .1.3.6.1.4.1.637.54.1.1.99.1.2.14 |
tsdimASAPGroupThis group describes the ASAP mandatory objects. Unknown .1.3.6.1.4.1.637.54.1.1.99.1.2.15 |
opticsIMSupportBckRstGroupThis group compounds object for backup and restore functionality Unknown .1.3.6.1.4.1.637.54.1.1.99.1.2.16 |
tsdimGenEventLogGroupThis group describes the mandatory objects needed for the Event Log management configuration. Unknown .1.3.6.1.4.1.637.54.1.1.99.1.2.17 |
opticsIMSwPackageGroupThis group describes the mandatory objects needed for the Software Package management. Unknown .1.3.6.1.4.1.637.54.1.1.99.1.2.18 |
opticsIMSwUnitGroupThis group describes the mandatory objects needed for the Sofwtare Unit management. Unknown .1.3.6.1.4.1.637.54.1.1.99.1.2.19 |
opticsIMSwDwlGroupThis group describes the mandatory objects needed for the Sofwtare Download management. Unknown .1.3.6.1.4.1.637.54.1.1.99.1.2.20 |
opticsIMNERestartGroupThis group describes the objects needed for the NE restart. Unknown .1.3.6.1.4.1.637.54.1.1.99.1.2.21 |
opticsIMAbnCondGroupThis group describes the objects needed for the Abnormal Condition management. Unknown .1.3.6.1.4.1.637.54.1.1.99.1.2.22 |
tsdimASAPOptGroupThis group describes the ASAP optional objects. Unknown .1.3.6.1.4.1.637.54.1.1.99.1.2.24 |
tsdimOptAPTGroupThis group describes the APT optional objects. Unknown .1.3.6.1.4.1.637.54.1.1.99.1.2.25 |
tsdimOptEventLogGroupThis group describes the event log optional objects. Unknown .1.3.6.1.4.1.637.54.1.1.99.1.2.26 |
tsdimOptAlarmLogGroupThis group describes the alarm log optional objects. Unknown .1.3.6.1.4.1.637.54.1.1.99.1.2.27 |
opticsIMEqptSwUnitGroupThis group describes the objects needed for the management of the Sofwtare Unit present i the equipment. Unknown .1.3.6.1.4.1.637.54.1.1.99.1.2.28 |
opticsIMOptAbnCondGroupThis group describes the abnormal condition optional objects. Unknown .1.3.6.1.4.1.637.54.1.1.99.1.2.29 |