TN-Y1564-MIB
AI MIB Summary
The TN-Y1564-MIB enables SNMP-based configuration and monitoring of system user accounts and authentication parameters on Nokia (formerly Alcatel-Lucent) TN (Transport Network) modules. This module specifically manages user session states, access privileges, and credential policies to enforce security compliance across transport network elements.
The MIB provides functionalities for system user management in TN modules.
Main OID:
tnY1564MIB.1.3.6.1.4.1.868.2.5.154
44
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
44 total| Object Name |
|---|
tnY1564MIBThe MIB provides functionalities for system user management in TN modules. MODULE-IDENTITY .1.3.6.1.4.1.868.2.5.154 |
tnY1564MIBNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.868.2.5.154.1 |
tnY1564MIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.868.2.5.154.2 |
tnY1564CfgMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.868.2.5.154.2.1 |
tnY1564ProfileTableThis table provides configuration of SOAM Maintenance Point. SEQUENCE OF TnY1564ProfileEntry .1.3.6.1.4.1.868.2.5.154.2.1.1 |
tnY1564ProfileEntryA entry in the table represents a configuration for local SOAM. TnY1564ProfileEntry .1.3.6.1.4.1.868.2.5.154.2.1.1.1 |
tnY1564ProfileNameThe name, ASCII range 33-126, of this table. SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.868.2.5.154.2.1.1.1.1 |
tnY1564ProfileDescriptionThe description of this table.rw DisplayString .1.3.6.1.4.1.868.2.5.154.2.1.1.1.2 |
tnY1564DuelEndedFor future use.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.868.2.5.154.2.1.1.1.3 |
tnY1564DstOamAwareWhen set, switch transmits Y.1731 DMM frames for delay measurements and Y.1731 1DM frames when this is cleared. When Traffic Type is 'Y.1731 OAM', switch transmits Y.1731 LBM frames as background traffic when DST is configured as OAM-aware, and Y.1731 TST frames when not.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.868.2.5.154.2.1.1.1.4 |
tnY1564TrafficTypeWhen set to 'Y.1731 OAM', this switch transmits Y.1731 OAM PDUs as background traffic, and DST is OAM-aware determines the PDU type. In the current version of the software, only one ECE can be tested at a time in this mode. When set to 'Simulated Customer', the software will generate a traffic-pattern per ECE that will hit the ECE, and use the ECE's counters to determine PASS/FAIL criteria.Besides supporting simultaneous test of multiple ECEs, 'Simulated Customer' has the advantage that the tester can see directly from the report if she has configured ECEs wrongly, since the report will show per-ECE counters and fail if an ECE under test is not hit as expected by the traffic pattern.rw Enumeration .1.3.6.1.4.1.868.2.5.154.2.1.1.1.5 |
tnY1564MegLevelThe MEG level used in generated Y.1731 OAM frames (both LBM/TST and DMM/1DM).rw Enumeration .1.3.6.1.4.1.868.2.5.154.2.1.1.1.6 |
tnY1564FrameSizeSelects the frame size of the background traffic. The frame size does not include possible C-tag(s) added to match the ECE. Besides standard frame sizes there are two custom selections: MTU - The UNI's MTU will be used for the background traffic. User-defined - custom specification of a frame size of the background traffic. Valid range is 64 to 10236 bytes.rw Enumeration .1.3.6.1.4.1.868.2.5.154.2.1.1.1.7 |
tnY1564UserFrameSizeUser defined frame size of the background traffic. Valid range is 64 to 10236 bytes.rw INTEGER .1.3.6.1.4.1.868.2.5.154.2.1.1.1.8 |
tnY1564DwellTimeWhen a trial (a single step of a subtest) is executed, background traffic is transmitted for a certain period of time. When that period has elapsed, the Dwell Time determines how long to wait before reading hardware counters and status in order to assess the status of the trial. The required dwell time must be at least the worst-case roundtrip time, and therefore a.o. depends on the physical distance between the near and far ends. Valid range is from 100 to 10000 in steps of 100 milliseconds with a default of 500 milliseconds.rw INTEGER .1.3.6.1.4.1.868.2.5.154.2.1.1.1.9 |
tnY1564SacFLRDefines the acceptable Frame Loss Ratio. The Acceptable FLR is measured in permille. Setting this to 1000 effectively disables this check.The number is used in all enabled subtests. Only delay measurement PDUs and green background traffic undergoes FLR check. If the number of looped green frames differs from the number of transmitted green frames by more than the 'Acceptable FLR', the test is considered failing, otherwise passing.If the EVC contains multiple ECEs that matches on the same VLAN ID (UNI ingress) and the EVC uses 'Tx Lookup' equal to 'VID-PCP', the NNI ingress rules count looped traffic per NNI outer tag's PCP, and therefore provide more detailed information about which ECE is failing, than if the EVC uses 'Tx Lookup' equal to 'VID', where all looped traffic arriving on NNI is counted on the same ECE. The disadvantage of the 'VID-PCP' method is that it uses more chip resources than does the 'VID' method. Valid range is from 0 to 1000 with a default of 0‰.rw INTEGER .1.3.6.1.4.1.868.2.5.154.2.1.1.1.10 |
tnY1564SacFTDDefines the acceptable Frame Transfer Delay, measured in milliseconds. If the highest observed frame transfer delay exceeds this, the test fails. Valid range is from 0 to 10000 with a default of 0 milliseconds. A value of 0 disables this check.rw INTEGER .1.3.6.1.4.1.868.2.5.154.2.1.1.1.11 |
tnY1564SacFDVDefines the acceptable Frame Delay Variation, measured in milliseconds. If the highest observed frame delay variation exceeds this, the test fails. Valid range is from 0 to 10000 with a default of 0 milliseconds. A value of 0 disables this check.rw INTEGER .1.3.6.1.4.1.868.2.5.154.2.1.1.1.12 |
tnY1564CirEnableSet, to enable the CIR test.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.868.2.5.154.2.1.1.1.13 |
tnY1564CirStepDurationEach step in the CIR configuration test applies background traffic for this number of seconds. Valid range is from 1 to 3600 with a default of 10 seconds.rw INTEGER .1.3.6.1.4.1.868.2.5.154.2.1.1.1.14 |
tnY1564CirDmIntervalA Y.1731 1DM or DMM frame (depending on type of test) is transmitted every so many milliseconds, in order to perform delay measurements (DM). The number should be selected so that at least three DM frames are transmitted during a trial in order to obtain delay variation results. After each trial the measured FTD and FDV is compared against the SAC's Acceptable FLR, FTD, and FDV. Valid range is from 100 to 10000 in steps of 100 milliseconds with a default of 500 milliseconds. A value of 0 effectively disables transmission of DM frames, which thereby indirectly disables the check against the SAC.rw INTEGER .1.3.6.1.4.1.868.2.5.154.2.1.1.1.15 |
tnY1564CirStepCountThe number of steps (trials) used to reach CIR. If, for example, Step Count is set to 4, four trials are executed. The first runs at 25% of this ECEs share of CIR, the second at 50%, then 75%, and finally 100%. A step count of 1 corresponds to executing Y.1564's A.1 test (Simple CIR Validation Test). A step count greater than 1 corresponds to executing Y.1564's A.2 test (Step Load CIR Test). Valid range is from 1 to 1000 with a default of 4 steps.rw INTEGER .1.3.6.1.4.1.868.2.5.154.2.1.1.1.16 |
tnY1564EirEnableSet, to enable the EIR test.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.868.2.5.154.2.1.1.1.17 |
tnY1564EirDurationThe EIR configuration test is executed in one single trial, whose duration is configured with this parameter. Valid range is from 1 to 3600 with a default of 10 seconds.rw INTEGER .1.3.6.1.4.1.868.2.5.154.2.1.1.1.18 |
tnY1564EirDmIntervalA Y.1731 1DM or DMM frame (depending on type of test) is transmitted every so many milliseconds, in order to perform delay measurements (DM). The number should be selected so that at least three DM frames are transmitted during a trial in order to obtain delay variation results. After each trial the measured FTD and FDV is compared against the SAC's Acceptable FLR, FTD, and FDV. Valid range is from 100 to 10000 in steps of 100 milliseconds with a default of 500 milliseconds. A value of 0 effectively disables transmission of DM frames, which thereby indirectly disables the check against the SAC.rw INTEGER .1.3.6.1.4.1.868.2.5.154.2.1.1.1.19 |
tnY1564TrafficPolicingEnableSet, to enable the Traffic Policing test.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.868.2.5.154.2.1.1.1.20 |
tnY1564TrafficPolicingDurationThe Traffic Policing test is executed in one single trial, whose duration is configured with this parameter. Valid range is from 1 to 3600 with a default of 10 seconds.rw INTEGER .1.3.6.1.4.1.868.2.5.154.2.1.1.1.21 |
tnY1564TrafficPolicingDmIntervalA Y.1731 1DM or DMM frame (depending on type of test) is transmitted every so many milliseconds, in order to perform delay measurements (DM). The number should be selected so that at least three DM frames are transmitted during a trial in order to obtain delay variation results. After each trial the measured FTD and FDV is compared against the SAC's Acceptable FLR, FTD, and FDV. Valid range is from 100 to 10000 in steps of 100 milliseconds with a default of 500 milliseconds. A value of 0 effectively disables transmission of DM frames, which thereby indirectly disables the check against the SAC.rw INTEGER .1.3.6.1.4.1.868.2.5.154.2.1.1.1.22 |
tnY1564PerfTestEnableSet, to enable the Performance test.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.868.2.5.154.2.1.1.1.23 |
tnY1564PerfTestDurationThe performance test is executed in one single trial, whose duration is configured with this parameter. There are Y.1564-specified standard durations and a custom duration can be specified by selecting User-defined Duration option.rw Enumeration .1.3.6.1.4.1.868.2.5.154.2.1.1.1.24 |
tnY1564PerfTestUserDurationUser defined duration. Valid range is from 1 to 86400 with a default of 900 secondsrw INTEGER .1.3.6.1.4.1.868.2.5.154.2.1.1.1.25 |
tnY1564PerfTestDmIntervalA Y.1731 1DM or DMM frame (depending on type of test) is transmitted every so many milliseconds, in order to perform delay measurements (DM). The number should be selected so that at least three DM frames are transmitted during a trial in order to obtain delay variation results. After each trial the measured FTD and FDV is compared against the SAC's Acceptable FLR, FTD, and FDV. Valid range is from 100 to 10000 in steps of 100 milliseconds with a default of 500 milliseconds. A value of 0 effectively disables transmission of DM frames, which thereby indirectly disables the check against the SAC.rw INTEGER .1.3.6.1.4.1.868.2.5.154.2.1.1.1.26 |
tnY1564ProfileStatusThe status of the row. The writable columns in a row can not be changed if the row is active. All columns must have a valid value before a row can be activated.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.868.2.5.154.2.1.1.1.27 |
tnY1564ReportMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.868.2.5.154.2.2 |
tnY1564ReportTableThis table provides configuration of SOAM Maintenance Point. SEQUENCE OF TnY1564ReportEntry .1.3.6.1.4.1.868.2.5.154.2.2.1 |
tnY1564ReportEntryA entry in the table represents a configuration for local SOAM. TnY1564ReportEntry .1.3.6.1.4.1.868.2.5.154.2.2.1.1 |
tnY1564ReportNameThe name, ASCII range 33-126, of this table. SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.868.2.5.154.2.2.1.1.1 |
tnY1564ReportDscrThe description of this table.ro DisplayString .1.3.6.1.4.1.868.2.5.154.2.2.1.1.2 |
tnY1564ReportTimeThe description of this table.ro DisplayString .1.3.6.1.4.1.868.2.5.154.2.2.1.1.3 |
tnY1564ReportTftpAddrTypeThe tftp server IP address type.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.868.2.5.154.2.2.1.1.4 |
tnY1564ReportTftpAddrThe tftp server IP address.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.868.2.5.154.2.2.1.1.5 |
tnY1564ReportTestStatusro Enumeration .1.3.6.1.4.1.868.2.5.154.2.2.1.1.6 |
tnY1564ReportActionrw Enumeration .1.3.6.1.4.1.868.2.5.154.2.2.1.1.7 |
tnY1564MIBConformance OBJECT IDENTIFIER .1.3.6.1.4.1.868.2.5.154.3 |