TN-THERMAL-PROTECTION-MIB
The TN-THERMAL-PROTECTION-MIB enables monitoring and management of port-level thermal thresholds and temperature sensor states on TN hardware to trigger protective shutdowns or alerts. It tracks real-time thermal metrics and protection event counters to prevent hardware damage caused by overheating conditions on network interfaces.
Imported Objects
Objects
16 total| Object Name |
|---|
tnThermalProtectionMIBThe mib module for thermal protection on ports MODULE-IDENTITY .1.3.6.1.4.1.868.2.5.32 |
tnThermalProtectionMIBNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.868.2.5.32.0 |
tnThermalProtectionPortStatusChangedNotificationA notification generated by the local device sensing a change in the thermal protection port status. The change indicates the current temperature of a port turns to be higher, or lower, than its priority temperature. NOTIFICATION-TYPE .1.3.6.1.4.1.868.2.5.32.0.1 |
tnThermalProtectionMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.868.2.5.32.1 |
tnThermalProtectionMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.868.2.5.32.1.1 |
tnThermalProtectionPriorityTableThis table is for user to configure the temperature and its priority which the ports belong to. SEQUENCE OF TnThermalProtectionPriorityEntry .1.3.6.1.4.1.868.2.5.32.1.1.1 |
tnThermalProtectionPriorityEntryEach entry represents a temperature and its priority, 4 priorities are supported. TnThermalProtectionPriorityEntry .1.3.6.1.4.1.868.2.5.32.1.1.1.1 |
tnThermalProtectionPriorityIndexThe priority the port belongs to. 4 priorities are supported.ro INTEGER .1.3.6.1.4.1.868.2.5.32.1.1.1.1.1 |
tnThermalProtectionPriorityTemperatureThe temperature at which the ports with the corresponding priority will be turned off. Temperatures between 0 and 255 C are supported.rw INTEGER .1.3.6.1.4.1.868.2.5.32.1.1.1.1.2 |
tnThermalProtectionIfTableThis table lets user to configure the temperature priority of each port for thermal protection. When the temperature exceeds the configured thermal protection temperature, ports will be turned off in order to protect the chip from getting overheated or decrease the power consumption. SEQUENCE OF TnThermalProtectionIfEntry .1.3.6.1.4.1.868.2.5.32.1.1.2 |
tnThermalProtectionIfEntryEach entry lists the temperature priority of each port. TnThermalProtectionIfEntry .1.3.6.1.4.1.868.2.5.32.1.1.2.1 |
tnThermalProtectionIfPriorityThe temperature priority of current port belongs to. Refer to tnThermalProtectionPriorityIndexrw INTEGER .1.3.6.1.4.1.868.2.5.32.1.1.2.1.1 |
tnThermalProtectionIfStatusTableThis table allows the user to inspect status information related to thermal protection. SEQUENCE OF TnThermalProtectionIfStatusEntry .1.3.6.1.4.1.868.2.5.32.1.1.3 |
tnThermalProtectionIfStatusEntryEach entry lists the temperature priority of each port. TnThermalProtectionIfStatusEntry .1.3.6.1.4.1.868.2.5.32.1.1.3.1 |
tnThermalProtectionIfStatusTemperatureShows the current chip temperature in degrees Celsius.ro INTEGER .1.3.6.1.4.1.868.2.5.32.1.1.3.1.1 |
tnThermalProtectionIfStatusCodeShows if the port is thermally protected (link is down) or if the port is operating normally.ro Enumeration .1.3.6.1.4.1.868.2.5.32.1.1.3.1.2 |
More MIBs from Transition
Browse all TransitionMIBs →SNMP MIB module
The TN-MPLS-MIB module enables the monitoring and configuration of Multiprotocol Label Switching (MPLS) parameters, including label bindings, forwarding equivalence classes, and tunnel states, on Nokia (formerly Alcatel-Lucent) Service Router and IP/MPLS network devices.
Standard SNMP MIB module defining data structures for TNI-MIB.
The TN-CES-MIB module enables monitoring and management of Circuit Emulation Service (CES) sessions on network equipment, specifically tracking performance metrics such as session status, packet loss, jitter, and synchronization errors for T1/E1 circuit emulation over packet-switched networks.
The TN-LLDP-MIB module enables monitoring and management of Link Layer Discovery Protocol (LLDP) neighbor discovery data, including system identification, port descriptions, and TLV (Type-Length-Value) attributes, on Trellix (formerly McAfee) network infrastructure devices. This private MIB extension facilitates the collection of LLDP session states and neighbor topology information for network inventory and connectivity verification.
The TN-DHCP-SERVER-MIB enables monitoring and management of Dynamic Host Configuration Protocol server configurations, lease states, and address pool utilization on Tanaza network infrastructure devices. This module provides visibility into DHCP scope assignments, client binding tables, and server operational status to facilitate network address administration.