TN-MGMT-TDM-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for TN-MGMT-TDM-MIB.
36
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
36 total| Object Name |
|---|
tnIfTDMAlarmIndicationSignalEvtA alarm indication signal event is sent when there is a warning or alarm on TDM port. NOTIFICATION-TYPE .1.3.6.1.4.1.7483.6.3.0.6 |
tnIfTDMTableThis table has entries for the TDM attributes. SEQUENCE OF TnIfTDMEntry .1.3.6.1.4.1.7483.6.3.1.2.6 |
tnIfTDMEntryA entry in the table represents TDM attributes. TnIfTDMEntry .1.3.6.1.4.1.7483.6.3.1.2.6.1 |
tnIfTDMAISTransmitTransmit AIS(All Ones/BLUE) on Fiber(Copper) as an error signal when
Copper interface(Fiber Interface) is down. When this error signal
is transmitted, the AIS of the device
on the other end is activated, if supportedrw Enumeration .1.3.6.1.4.1.7483.6.3.1.2.6.1.1 |
tnIfTDMAISFormatTransmit AIS(All Ones:1111... sequence/BLUE:0101... sequence) on Fiber(Copper) as an error signal for DS3/E3/STS-1 portrw Enumeration .1.3.6.1.4.1.7483.6.3.1.2.6.1.2 |
tnIfTDMAlarmIndicationSignalWhen equal to alarm(1),
this means that the other end has TAOS enabled
and is currently transmitting an alarm condition.
when equal to normal, this means no alarm.ro Enumeration .1.3.6.1.4.1.7483.6.3.1.2.6.1.3 |
tnIfTDMLongHaulThis variable indicates the current position of the
remote device's Short/Long haul configuration switch.ro Enumeration .1.3.6.1.4.1.7483.6.3.1.2.6.1.4 |
tnIfTDMTypeThis variable indicates the type of the current device.
T1=1.544MHz; E1=2.048MHz;E3 = 34.4Mb/s; DS3 = 44.7Mb/s; STS-1 = 51.8Mb/sro Enumeration .1.3.6.1.4.1.7483.6.3.1.2.6.1.5 |
tnIfTDMT1E1LineBuildoutThe characteristics T1E1 card's copper interface.ro Enumeration .1.3.6.1.4.1.7483.6.3.1.2.6.1.6 |
tnIfTDMDS3E3LineBuildoutThe characteristics of DS3E3 card's copper interface.rw Enumeration .1.3.6.1.4.1.7483.6.3.1.2.6.1.7 |
tnIfTDMConnectorTypeThe style of connector built into this device.ro CpsConnector (TRANSITION-TC) .1.3.6.1.4.1.7483.6.3.1.2.6.1.8 |
tnIfTDMExtTableThis table has entries for the Extral TDM attributes. SEQUENCE OF TnIfTDMExtEntry .1.3.6.1.4.1.7483.6.3.1.2.9 |
tnIfTDMExtEntryA entry in the table represents Extral TDM attributes. TnIfTDMExtEntry .1.3.6.1.4.1.7483.6.3.1.2.9.1 |
tnIfTDMExtIdAn index that uniquely identifies an entry
in the tnIfTDMExtTable. This index permits
the same interface to have several different
channels INTEGER .1.3.6.1.4.1.7483.6.3.1.2.9.1.1 |
tnIfTDMExtAISTrasmitTransmit AIS(All Ones/BLUE) on the Channel as an error signal when
Copper interface(Fiber Interface) is down. When this error signal
is transmitted, the AIS of the device on the other end is activated,
if supportedrw Enumeration .1.3.6.1.4.1.7483.6.3.1.2.9.1.2 |
tnIfTDMExtAISFormatTransmit AIS(All Ones:1111... sequence/BLUE:0101... sequence)
on the Channel as an error signal for the pair portrw Enumeration .1.3.6.1.4.1.7483.6.3.1.2.9.1.3 |
tnIfTDMExtAlarmIndicationSingnalWhen equal to alarm(1),
this means that the other end of Channel has AIS enabled
and is currently transmitting an alarm condition.
when equal to normal(2), this means no alarm.
when equal to yellow(3), this means the other end of Channel has YELLOW enabled
and is currently transmitting a YELLOW condition.
when equal to red(4), this means the local end of Channel has detect a LOS on receiver.ro Enumeration .1.3.6.1.4.1.7483.6.3.1.2.9.1.4 |
tnIfTDMExtLoopbackThis variable indicates the loopback state of the current Channelrw Enumeration .1.3.6.1.4.1.7483.6.3.1.2.9.1.5 |
tnIfTDMExtYellowTrasmitTransmit Yellow on the Channel as an error signal when Local Copper Interface is down.
When this error signal is transmitted.rw Enumeration .1.3.6.1.4.1.7483.6.3.1.2.9.1.6 |
tnIfTDM2TableThis table has entries for the TDM 2 attributes. SEQUENCE OF TnIfTDM2Entry .1.3.6.1.4.1.7483.6.3.1.2.10 |
tnIfTDM2EntryA entry in the table represents the TDM 2 attributes. TnIfTDM2Entry .1.3.6.1.4.1.7483.6.3.1.2.10.1 |
tnIfTDM2FiberLineNumThis variable is indicate the links number of the Fiber Port, maybe single line or dual linero INTEGER .1.3.6.1.4.1.7483.6.3.1.2.10.1.1 |
tnIfTDM2FiberActiveLineThis variable is indicate the active fiber link, if a multi-fiber line
is used for hardware redundancyrw Enumeration .1.3.6.1.4.1.7483.6.3.1.2.10.1.2 |
tnIfTDM2FiberRevertiveThis variable is used to decide whether to revertive the fiber link to primary link if applicablerw Enumeration .1.3.6.1.4.1.7483.6.3.1.2.10.1.3 |
tnIfTDM2FiberPrimaryLinkStatusThis variable indicates the fiber port primary line link statusro Enumeration .1.3.6.1.4.1.7483.6.3.1.2.10.1.4 |
tnIfTDM2FiberSecondaryLinkStatusThis variable indicates the fiber port secondary line link statusro Enumeration .1.3.6.1.4.1.7483.6.3.1.2.10.1.5 |
tnIfTDM2InBandLPEnableThis variable indicates whether In-band Loopback detect is enabledrw Enumeration .1.3.6.1.4.1.7483.6.3.1.2.10.1.6 |
tnIfTDM2InBandLPStartPattenThis binary string is used to set the In-band Loopback start Patten,
such as 11000 stringrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7483.6.3.1.2.10.1.7 |
tnIfTDM2InBandLPStopPattenThis binary string is used to set the In-band Loopback stop Patten,
such as 11100 stringrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7483.6.3.1.2.10.1.8 |
tnIfTDM2InBandPEERLPEnableThis variable indicates whether the PEER interface In-band Loopback detect is enabledrw Enumeration .1.3.6.1.4.1.7483.6.3.1.2.10.1.9 |
tnIfTDM2InBandPEERLPStartPattenThis binary string is used to set the PEER interface In-band Loopback start Patten,
such as 11000 stringrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7483.6.3.1.2.10.1.10 |
tnIfTDM2InBandPEERLPStopPattenThis binary string is used to set the PEER interface In-band Loopback stop Patten,
such as 11100 stringrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7483.6.3.1.2.10.1.11 |
tnIfTDM2InBandLPTimeoutEnableThis variable indicates whether the In-band Loopback timeout watchdog is enabledrw Enumeration .1.3.6.1.4.1.7483.6.3.1.2.10.1.12 |
tnIfTDM2InBandLPTimeoutCountThis variable is used to set the In-band Loopback timeout watchdog value, the unit is minuterw INTEGER .1.3.6.1.4.1.7483.6.3.1.2.10.1.13 |
tnIfTDM2InBandPEERLPTimeoutEnableThis variable indicates whether the Peer In-band Loopback timeout watchdog is enabledrw Enumeration .1.3.6.1.4.1.7483.6.3.1.2.10.1.14 |
tnIfTDM2InBandPEERLPTimeoutCountThis variable is used to set the Peer In-band Loopback timeout watchdog value, the unit is minuterw INTEGER .1.3.6.1.4.1.7483.6.3.1.2.10.1.15 |