TE-LINK-STD-MIB
Copyright (C) 2005 The Internet Society. This version of this MIB module is part of RFC 4220; see the RFC itself for full legal notices. This MIB module contains managed object definitions for MPLS traffic engineering links as defined in 'Link Bundling in MPLS Traffic Engineering (TE)'.
Main OID:
teLinkStdMIB.1.3.6.1.2.1.10.200
88
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
88 total| Object Name |
|---|
teLinkStdMIBCopyright (C) 2005 The Internet Society. This version of this MIB module is part of RFC 4220; see the RFC itself for full legal notices. This MIB module contains managed object definitions for MPLS traffic engineering links as defined in 'Link Bundling in MPLS Traffic Engineering (TE)'. MODULE-IDENTITY .1.3.6.1.2.1.10.200 |
teLinkNotifications OBJECT IDENTIFIER .1.3.6.1.2.1.10.200.0 |
teLinkObjects OBJECT IDENTIFIER .1.3.6.1.2.1.10.200.1 |
teLinkTableThis table specifies the grouping of component links into TE links and the grouping of TE links into bundled links. SEQUENCE OF TeLinkEntry .1.3.6.1.2.1.10.200.1.1 |
teLinkEntryAn entry in this table exists for each ifEntry with an ifType of teLink(200), i.e., for every TE link. An ifEntry in the ifTable must exist before a teLinkEntry is created with the corresponding ifIndex. If a TE link entry in the ifTable is destroyed, then so is the corresponding entry in the teLinkTable. The administrative and operational status values are controlled from the ifEntry. TeLinkEntry .1.3.6.1.2.1.10.200.1.1.1 |
teLinkAddressTypeThe type of Internet address for the TE link.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.2.1.10.200.1.1.1.1 |
teLinkLocalIpAddrThe local Internet address for numbered links. The type of this address is determined by the value of the teLinkAddressType object. For IPv4 and IPv6 numbered links, this object represents the local IP address associated with the TE link. For an unnumbered link, the local address is of type unknown, this object is set to the zero length string, and the teLinkOutgoingIfId object then identifies the unnumbered address. If the TE link is a Forwarding Adjacency (FA), the local IP address is set to the head-end address of the FA-LSP. If ipAddrTable is implemented, this object must have the same value as the ipAdEntAddr object that belongs to the row in ipAddrTable where ipAdEntIfIndex is equal to ifIndex.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.2.1.10.200.1.1.1.2 |
teLinkRemoteIpAddrThe remote Internet address for numbered links. The type of this address is determined by the value of the teLinkAddressType object. The remote IP address associated with the TE link (IPv4 and IPv6 numbered links). For an unnumbered link, the remote address is of type unknown, this object is set to the zero length string, and the teLinkIncomingIfId object then identifies the unnumbered address. If the TE link is a Forwarding Adjacency, the remote IP address is set to the tail-end address of the FA-LSP.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.2.1.10.200.1.1.1.3 |
teLinkMetricThe traffic engineering metric for the TE link is derived from its component links. All component links within the TE link must have the same traffic engineering metric.rw Unsigned32 .1.3.6.1.2.1.10.200.1.1.1.4 |
teLinkMaximumReservableBandwidthThis attribute specifies the maximum reservable bandwidth on the TE link. This is the union of the maximum reservable bandwidth of all the component links within the TE link that can be used to carry live traffic.ro TeLinkBandwidth UNITS "bps" .1.3.6.1.2.1.10.200.1.1.1.5 |
teLinkProtectionTypeThis attribute specifies the link protection type of the TE link. Descriptions of the different protection types can be found in the 'Routing Extensions in Support of Generalized Multi-Protocol Label Switching (GMPLS)' document.rw Enumeration .1.3.6.1.2.1.10.200.1.1.1.6 |
teLinkWorkingPriorityThis object represents a priority value such that a new connection with a higher priority, i.e., numerically lower than this value, is guaranteed to be setup on a primary link and not on a secondary link.rw TeLinkPriority .1.3.6.1.2.1.10.200.1.1.1.7 |
teLinkResourceClassThis attribute specifies the TE link resource class. The resource class is a 32 bit bitfield. The resource class for a link bundle is derived from the resource class of its TE links. All TE links within a link bundle must have the same resource class. Encoding of the resource class is described in the 'Traffic Engineering (TE) Extensions to OSPF Version 2' document.rw Unsigned32 .1.3.6.1.2.1.10.200.1.1.1.8 |
teLinkIncomingIfIdFor unnumbered links, the incoming interface is set to the outgoing interface identifier chosen by the neighboring LSR for the reverse link corresponding to this TE link. If the link is numbered, the value of this object is 0 and the address is stored in the teLinkRemoteIpAddr instead.rw Integer32 .1.3.6.1.2.1.10.200.1.1.1.9 |
teLinkOutgoingIfIdIf the link is unnumbered, the outgoing interface identifier is set to the outgoing interface identifier chosen for the TE link by the advertising LSR. If the link is numbered, the value of this object is 0 and the address is stored in the teLinkLocalIpAddr instead.rw InterfaceIndexOrZero (IF-MIB) .1.3.6.1.2.1.10.200.1.1.1.10 |
teLinkRowStatusThis variable is used to create, modify, and/or delete a row in this table. None of the writable objects in a row can be changed if status is active(1).rw RowStatus (SNMPv2-TC) .1.3.6.1.2.1.10.200.1.1.1.11 |
teLinkStorageTypeThe storage type for this conceptual row in the teLinkTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row.rw StorageType (SNMPv2-TC) .1.3.6.1.2.1.10.200.1.1.1.12 |
teLinkDescriptorTableThis table specifies the interface switching capability descriptors associated with the TE links. SEQUENCE OF TeLinkDescriptorEntry .1.3.6.1.2.1.10.200.1.2 |
teLinkDescriptorEntryAn entry in this table is created for every TE link interface switching capability descriptor. An ifEntry in the ifTable must exist before a teLinkDescriptorEntry using the same ifIndex is created. ifType of ifEntry must be teLink(200). If a TE link entry in the ifTable is destroyed, then so are all of the entries in the teLinkDescriptorTable that use the ifIndex of this TE link. TeLinkDescriptorEntry .1.3.6.1.2.1.10.200.1.2.1 |
teLinkDescriptorIdThis object specifies the link descriptor identifier. Unsigned32 .1.3.6.1.2.1.10.200.1.2.1.1 |
teLinkDescrSwitchingCapabilityThis attribute specifies interface switching capability of the TE link, which is derived from its component links.rw TeLinkSwitchingCapability .1.3.6.1.2.1.10.200.1.2.1.2 |
teLinkDescrEncodingTypeThis attribute specifies the TE link encoding type.rw TeLinkEncodingType .1.3.6.1.2.1.10.200.1.2.1.3 |
teLinkDescrMinLspBandwidthThis attribute specifies the minimum LSP bandwidth on the TE link. This is derived from the union of the minimum LSP bandwidth of all the component links associated with the TE link that can be used to carry live traffic.rw TeLinkBandwidth UNITS "bps" .1.3.6.1.2.1.10.200.1.2.1.4 |
teLinkDescrMaxLspBandwidthPrio0This attribute specifies the maximum LSP bandwidth at priority 0 on the TE link. This is the union of the maximum LSP bandwidth at priority 0 of all the component links within the TE link that can be used to carry live traffic.rw TeLinkBandwidth UNITS "bps" .1.3.6.1.2.1.10.200.1.2.1.5 |
teLinkDescrMaxLspBandwidthPrio1This attribute specifies the maximum LSP bandwidth at priority 1 on the TE link. This is the union of the maximum LSP bandwidth at priority 1 of all the component links within the TE link that can be used to carry live traffic.rw TeLinkBandwidth UNITS "bps" .1.3.6.1.2.1.10.200.1.2.1.6 |
teLinkDescrMaxLspBandwidthPrio2This attribute specifies the maximum LSP bandwidth at priority 2 on the TE link. This is the union of the maximum LSP bandwidth at priority 2 of all the component links within the TE link that can be used to carry live traffic.rw TeLinkBandwidth UNITS "bps" .1.3.6.1.2.1.10.200.1.2.1.7 |
teLinkDescrMaxLspBandwidthPrio3This attribute specifies the maximum LSP bandwidth at priority 3 on the TE link. This is the union of the maximum LSP bandwidth at priority 3 of all the component links within the TE link that can be used to carry live traffic.rw TeLinkBandwidth UNITS "bps" .1.3.6.1.2.1.10.200.1.2.1.8 |
teLinkDescrMaxLspBandwidthPrio4This attribute specifies the maximum LSP bandwidth at priority 4 on the TE link. This is the union of the maximum LSP bandwidth at priority 4 of all the component links within the TE link that can be used to carry live traffic.rw TeLinkBandwidth UNITS "bps" .1.3.6.1.2.1.10.200.1.2.1.9 |
teLinkDescrMaxLspBandwidthPrio5This attribute specifies the maximum LSP bandwidth at priority 5 on the TE link. This is the union of the maximum LSP bandwidth at priority 5 of all the component links within the TE link that can be used to carry live traffic.rw TeLinkBandwidth UNITS "bps" .1.3.6.1.2.1.10.200.1.2.1.10 |
teLinkDescrMaxLspBandwidthPrio6This attribute specifies the maximum LSP bandwidth at priority 6 on the TE link. This is the union of the maximum LSP bandwidth at priority 6 of all the component links within the TE link that can be used to carry live traffic.rw TeLinkBandwidth UNITS "bps" .1.3.6.1.2.1.10.200.1.2.1.11 |
teLinkDescrMaxLspBandwidthPrio7This attribute specifies the maximum LSP bandwidth at priority 7 on the TE link. This is the union of the maximum LSP bandwidth at priority 7 of all the component links within the TE link that can be used to carry live traffic.rw TeLinkBandwidth UNITS "bps" .1.3.6.1.2.1.10.200.1.2.1.12 |
teLinkDescrInterfaceMtuThis attribute specifies the interface MTU for the TE link descriptor.rw Unsigned32 .1.3.6.1.2.1.10.200.1.2.1.13 |
teLinkDescrIndicationThis attribute specifies whether this interface supports Standard or Arbitrary SONET/SDH.rw TeLinkSonetSdhIndication .1.3.6.1.2.1.10.200.1.2.1.14 |
teLinkDescrRowStatusThis variable is used to create, modify, and/or delete a row in this table. No read-create object can be changed if teLinkDescrRowStatus is in the active(1) state.rw RowStatus (SNMPv2-TC) .1.3.6.1.2.1.10.200.1.2.1.15 |
teLinkDescrStorageTypeThe storage type for this conceptual row in the teLinkDescriptorTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row.rw StorageType (SNMPv2-TC) .1.3.6.1.2.1.10.200.1.2.1.16 |
teLinkSrlgTableThis table specifies the SRLGs associated with TE links. SEQUENCE OF TeLinkSrlgEntry .1.3.6.1.2.1.10.200.1.3 |
teLinkSrlgEntryAn entry in this table contains information about an SRLG associated with a TE link. An ifEntry in the ifTable must exist before a teLinkSrlgEntry using the same ifIndex is created. The ifType of ifEntry must be teLink(200). If a TE link entry in the ifTable is destroyed, then so are all of the entries in the teLinkSrlgTable that use the ifIndex of this TE link. TeLinkSrlgEntry .1.3.6.1.2.1.10.200.1.3.1 |
teLinkSrlgThis identifies an SRLG supported by the TE link. An SRLG is identified with a 32-bit number that is unique within an IGP domain. Zero is a valid SRLG number. Unsigned32 .1.3.6.1.2.1.10.200.1.3.1.1 |
teLinkSrlgRowStatusThis variable is used to create, modify, and/or delete a row in this table. No read-create object can be modified if teLinkSrlgRowStatus is active(1).rw RowStatus (SNMPv2-TC) .1.3.6.1.2.1.10.200.1.3.1.2 |
teLinkSrlgStorageTypeThe storage type for this conceptual row in the teLinkSrlgTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row.rw StorageType (SNMPv2-TC) .1.3.6.1.2.1.10.200.1.3.1.3 |
teLinkBandwidthTableThis table specifies the priority-based bandwidth table for TE links. SEQUENCE OF TeLinkBandwidthEntry .1.3.6.1.2.1.10.200.1.4 |
teLinkBandwidthEntryAn entry in this table contains information about the priority-based bandwidth of TE links. An ifEntry in the ifTable must exist before a teLinkBandwidthEntry using the same ifIndex is created. The ifType of ifEntry must be teLink(200). If a TE link entry in the ifTable is destroyed, then so are all of the entries in the teLinkBandwidthTable that use the ifIndex of this TE link. TeLinkBandwidthEntry .1.3.6.1.2.1.10.200.1.4.1 |
teLinkBandwidthPriorityThis attribute specifies the priority. A value of 0 is valid as specified in the 'Traffic Engineering (TE) Extensions to OSPF Version 2' document. TeLinkPriority .1.3.6.1.2.1.10.200.1.4.1.1 |
teLinkBandwidthUnreservedThis attribute specifies the TE link unreserved bandwidth at priority p. It is the sum of the unreserved bandwidths at priority p of all component links associated with the TE link (excluding all links that are strictly used as protecting links).ro TeLinkBandwidth UNITS "bps" .1.3.6.1.2.1.10.200.1.4.1.2 |
teLinkBandwidthRowStatusThis variable is used to create, modify, and/or delete a row in this table. No read-create object can be modified when teLinkBandwidthRowStatus is active(1).rw RowStatus (SNMPv2-TC) .1.3.6.1.2.1.10.200.1.4.1.3 |
teLinkBandwidthStorageTypeThe storage type for this conceptual row in the teLinkBandwidthTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row.rw StorageType (SNMPv2-TC) .1.3.6.1.2.1.10.200.1.4.1.4 |
componentLinkTableThis table specifies the component link parameters. SEQUENCE OF ComponentLinkEntry .1.3.6.1.2.1.10.200.1.5 |
componentLinkEntryAn entry in this table exists for each ifEntry that represents a component link. An ifEntry must exist in the ifTable before a componentLinkEntry is created with the corresponding ifIndex. ifEntry's ifType can be of any interface type that has been defined for TE Link interworking. Examples include ATM, Frame Relay, Ethernet, etc. If an entry representing a component link is destroyed in the ifTable, then so is the corresponding entry in the componentLinkTable. The administrative and operational status values are controlled from the ifEntry. ComponentLinkEntry .1.3.6.1.2.1.10.200.1.5.1 |
componentLinkMaxResBandwidthThis attribute specifies the maximum reservable bandwidth on the component link.rw TeLinkBandwidth UNITS "bps" .1.3.6.1.2.1.10.200.1.5.1.1 |
componentLinkPreferredProtectionThis attribute specifies whether this component link is a primary or secondary entity.rw TeLinkProtection .1.3.6.1.2.1.10.200.1.5.1.2 |
componentLinkCurrentProtectionThis attribute specifies whether this component link is currently used as primary or secondary link.ro TeLinkProtection .1.3.6.1.2.1.10.200.1.5.1.3 |
componentLinkRowStatusThis variable is used to create, modify, and/or delete a row in this table. No read-create object can be modified when componentLinkRowStatus is active(1).rw RowStatus (SNMPv2-TC) .1.3.6.1.2.1.10.200.1.5.1.4 |
componentLinkStorageTypeThe storage type for this conceptual row in the componentLinkTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row.rw StorageType (SNMPv2-TC) .1.3.6.1.2.1.10.200.1.5.1.5 |
componentLinkDescriptorTableThis table specifies the interface switching capability descriptors associated with the component links. SEQUENCE OF ComponentLinkDescriptorEntry .1.3.6.1.2.1.10.200.1.6 |
componentLinkDescriptorEntryAn entry in this table is created for every component link descriptor. An ifEntry in the ifTable must exist before a componentLinkDescriptorEntry using the same ifIndex is created. ifEntry's ifType can be of any interface type that has been defined for TE Link interworking. Examples include ATM, Frame Relay, Ethernet, etc. If a component link entry in the ifTable is destroyed, then so are all entries in the componentLinkDescriptorTable that use the ifIndex of this component link. ComponentLinkDescriptorEntry .1.3.6.1.2.1.10.200.1.6.1 |
componentLinkDescrIdThis object specifies the link descriptor identifier. Unsigned32 .1.3.6.1.2.1.10.200.1.6.1.1 |
componentLinkDescrSwitchingCapabilityThis attribute specifies link multiplexing capabilities of the component link.rw TeLinkSwitchingCapability .1.3.6.1.2.1.10.200.1.6.1.2 |
componentLinkDescrEncodingTypeThis attribute specifies the component link encoding type.rw TeLinkEncodingType .1.3.6.1.2.1.10.200.1.6.1.3 |
componentLinkDescrMinLspBandwidthThis attribute specifies the minimum LSP bandwidth on the component link.rw TeLinkBandwidth UNITS "bps" .1.3.6.1.2.1.10.200.1.6.1.4 |
componentLinkDescrMaxLspBandwidthPrio0This attribute specifies the maximum LSP bandwidth at priority 0 on the component link.rw TeLinkBandwidth UNITS "bps" .1.3.6.1.2.1.10.200.1.6.1.5 |
componentLinkDescrMaxLspBandwidthPrio1This attribute specifies the maximum LSP bandwidth at priority 1 on the component link.rw TeLinkBandwidth UNITS "bps" .1.3.6.1.2.1.10.200.1.6.1.6 |
componentLinkDescrMaxLspBandwidthPrio2This attribute specifies the maximum LSP bandwidth at priority 2 on the component link.rw TeLinkBandwidth UNITS "bps" .1.3.6.1.2.1.10.200.1.6.1.7 |
componentLinkDescrMaxLspBandwidthPrio3This attribute specifies the maximum LSP bandwidth at priority 3 on the component link.rw TeLinkBandwidth UNITS "bps" .1.3.6.1.2.1.10.200.1.6.1.8 |
componentLinkDescrMaxLspBandwidthPrio4This attribute specifies the maximum LSP bandwidth at priority 4 on the component link.rw TeLinkBandwidth UNITS "bps" .1.3.6.1.2.1.10.200.1.6.1.9 |
componentLinkDescrMaxLspBandwidthPrio5This attribute specifies the maximum LSP bandwidth at priority 5 on the component link.rw TeLinkBandwidth UNITS "thousand bps" .1.3.6.1.2.1.10.200.1.6.1.10 |
componentLinkDescrMaxLspBandwidthPrio6This attribute specifies the maximum LSP bandwidth at priority 6 on the component link.rw TeLinkBandwidth UNITS "bps" .1.3.6.1.2.1.10.200.1.6.1.11 |
componentLinkDescrMaxLspBandwidthPrio7This attribute specifies the maximum LSP bandwidth at priority 7 on the component link.rw TeLinkBandwidth UNITS "bps" .1.3.6.1.2.1.10.200.1.6.1.12 |
componentLinkDescrInterfaceMtuThis attribute specifies the interface MTU for the component link descriptor.rw Unsigned32 .1.3.6.1.2.1.10.200.1.6.1.13 |
componentLinkDescrIndicationThis attribute specifies whether this interface supports Standard or Arbitrary SONET/SDH.rw TeLinkSonetSdhIndication .1.3.6.1.2.1.10.200.1.6.1.14 |
componentLinkDescrRowStatusThis variable is used to create, modify, and/or delete a row in this table. No read-create object can be modified when componentLinkDescrRowStatus is active(1).rw RowStatus (SNMPv2-TC) .1.3.6.1.2.1.10.200.1.6.1.15 |
componentLinkDescrStorageTypeThe storage type for this conceptual row in the componentLinkDescriptorTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row.rw StorageType (SNMPv2-TC) .1.3.6.1.2.1.10.200.1.6.1.16 |
componentLinkBandwidthTableThis table specifies the priority-based bandwidth for component links. SEQUENCE OF ComponentLinkBandwidthEntry .1.3.6.1.2.1.10.200.1.7 |
componentLinkBandwidthEntryAn entry in this table contains information about the priority-based bandwidth on component links. An ifEntry in the ifTable must exist before a componentLinkBandwidthEntry using the same ifIndex is created. ifEntry's ifType can be of any interface type that has been defined for TE Link interworking. Examples include ATM, Frame Relay, Ethernet, etc. If a component link entry in the ifTable is destroyed, then so are all entries in the componentLinkBandwidthTable that use the ifIndex of this component link. ComponentLinkBandwidthEntry .1.3.6.1.2.1.10.200.1.7.1 |
componentLinkBandwidthPriorityThis attribute specifies the priority. A value of 0 is valid as specified in the 'Traffic Engineering (TE) Extensions to OSPF Version 2' document. TeLinkPriority .1.3.6.1.2.1.10.200.1.7.1.1 |
componentLinkBandwidthUnreservedThis attribute specifies the component link unreserved bandwidth at priority p.ro TeLinkBandwidth UNITS "bps" .1.3.6.1.2.1.10.200.1.7.1.2 |
componentLinkBandwidthRowStatusThis variable is used to create, modify, and/or delete a row in this table. No read-create object can be modified when componentLinkBandwidthRowStatus is active(1).rw RowStatus (SNMPv2-TC) .1.3.6.1.2.1.10.200.1.7.1.3 |
componentLinkBandwidthStorageTypeThe storage type for this conceptual row in the componentLinkBandwidthTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row.rw StorageType (SNMPv2-TC) .1.3.6.1.2.1.10.200.1.7.1.4 |
teLinkConformance OBJECT IDENTIFIER .1.3.6.1.2.1.10.200.2 |
teLinkCompliances OBJECT IDENTIFIER .1.3.6.1.2.1.10.200.2.1 |
teLinkModuleFullComplianceCompliance statement for agents that support read-create so that both configuration and monitoring of TE links can be accomplished via this MIB module. Unknown .1.3.6.1.2.1.10.200.2.1.1 |
teLinkModuleReadOnlyComplianceCompliance statement for agents that support the monitoring of the TE link MIB module. Unknown .1.3.6.1.2.1.10.200.2.1.2 |
teLinkGroups OBJECT IDENTIFIER .1.3.6.1.2.1.10.200.2.2 |
teLinkGroupCollection of objects needed for the management of resources associated with TE links. Unknown .1.3.6.1.2.1.10.200.2.2.1 |
teLinkSrlgGroupCollection of objects needed for the management of SRLG resources associated with TE links. Unknown .1.3.6.1.2.1.10.200.2.2.2 |
teLinkBandwidthGroupCollection of objects needed for the management of the bandwidth resources associated with TE links and component links. Unknown .1.3.6.1.2.1.10.200.2.2.3 |
componentLinkBandwidthGroupCollection of objects needed for the management of the bandwidth parameters associated with component links. Unknown .1.3.6.1.2.1.10.200.2.2.4 |
teLinkPscGroupCollection of objects needed for devices that are packet switch capable. Unknown .1.3.6.1.2.1.10.200.2.2.5 |
teLinkTdmGroupCollection of objects needed for devices that are TDM switching capable. Unknown .1.3.6.1.2.1.10.200.2.2.6 |