TCOP-OPT-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
76
Objects
Active
Status
2
Dependencies
Imported Objects
Objects
76 total| Object Name |
|---|
codex OBJECT IDENTIFIER .1.3.6.1.4.1.449 |
RFC1155-SMI Unknown .1.3.6.1.4.1.449 |
cdxProductSpecific OBJECT IDENTIFIER .1.3.6.1.4.1.449.2 |
cdx6500 OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1 |
cdx6500Configuration OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.2 |
cdx6500CfgProtocolGroup OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.2.1 |
cdx6500PCTPortProtocolGroup OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.2.1.1 |
cdx6500PPCTTCOPPortTableThis table contains TCOP Port configuration parameters. SEQUENCE OF Cdx6500PPCTTCOPPortEntry .1.3.6.1.4.1.449.2.1.2.1.1.23 |
cdx6500PPCTTCOPPortEntryEach PortEntry contains the configuration
parameters for one TCOP port. Cdx6500PPCTTCOPPortEntry .1.3.6.1.4.1.449.2.1.2.1.1.23.1 |
cdx6500TCOPCfgPortNumberPort number of the port being used by TCOP.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.23.1.1 |
cdx6500TCOPCfgSubtypeSelect the sub-type for the synchronous protocol
running on this port.
hsc3 - Transparent Hitachi type
gnet - Transparent GNET type.
uts - Transparent Uniscope type.
slc - Synchronous Link Control.
ac100 - AC100.ro Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.23.1.2 |
cdx6500TCOPCfgClockSourceint - internal clock source
ext - external clock source on pins 18 and 24.ro Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.23.1.3 |
cdx6500TCOPCfgClockSpeedThis is the port speed in bits per second,
when clock source = int.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.23.1.4 |
cdx6500TCOPCfgContentionSpecifies the line contention.
hdx - Half duplex, DCD toggles
fdx - Full duplex, DCD is always high.ro Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.23.1.5 |
cdx6500TCOPCfgCodeTypeEither of ascii or ebcdic code set is used.ro Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.23.1.6 |
cdx6500TCOPCfgReceiveByteCountSpecifies the number of bytes collected from the
line before data is forwarded to the network.
A minimum byte count constraint is imposed for
port speed intervals as shown in the following
pairs of (port speed in bps, minimum byte count):
(19200 to 80000, 127); (9600 to 19200, 64);
(4800 to 9600, 32); (2400 to 4800, 16);
(below 2400, 8).ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.23.1.7 |
cdx6500TCOPCfgCallControlnone - port will generate a call
auto - Autocalling enabled.ro Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.23.1.8 |
cdx6500TCOPCfgAutoCallMnemThis mnemonic name is used for Auto calling.ro DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.23.1.9 |
cdx6500TCOPCfgAutoCallTOSpecifies the time in seconds between call
attempts when autocalling.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.23.1.10 |
cdx6500TCOPCfgMaxAutoCallTriesSpecifies the maximum number of times the TCOP port
will attempt to call. A value of 0 will allow
unlimited number of attempts.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.23.1.11 |
cdx6500TCOPCfgPortAddressThe BCD address specified here is inserted in
the calling address field when the TCOP port
makes a call.ro DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.23.1.12 |
cdx6500TCOPCfgProtocolIDThe protocol identifier specified here is
inserted into a call packet or checked against
the identifier of an incoming call.ro DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.23.1.13 |
cdx6500TCOPCfgEnableBillThis controls whether billing (accounting) records
will be created for calls on this TCOP port.ro Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.23.1.14 |
cdx6500TCOPCfgRestrictConnSpecifies the destination of all calls routed
to from this port, regardless of route selection
table entries. For example, to route calls to
port 1, use P1. To route calls to port 2,
station 4, use P2S4. To route call to X25
port 2, enter X25-2. Blank this field to disable
this functionality.ro DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.23.1.15 |
cdx6500TCOPCfgRXQueueSpecifies the maximum number of received
messages to be queued. This parameter is
effective only when sub-type = gnet.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.23.1.16 |
cdx6500TCOPCfgTXQueueSpecifies the maximum number of transmit messages to
be queued. This parameter is effective only when
sub-type = gnet.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.23.1.17 |
cdx6500TCOPCfgQueueOverflowSpecifies the action to be taken if the receive
message queue overflows. This parameter is
effective only when sub-type = gnet.
resetConnection - Reset connections
dropMessage - Drop the message causing overflow
flushQueue - Flush the queue
eotMessage - Flush the queue when receiving
message terminated with EOT.ro Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.23.1.18 |
cdx6500TCOPCfgPortTypeThe Port Type of the port.ro Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.23.1.19 |
cdx6500TCOPCfgDataTransmissionThis determines the mode of data transfer.
hdx - Indicates half duplex data transfer.
fdx - Indicates full duplex data transfer.ro Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.23.1.20 |
cdx6500TCOPCfgElectricalInterfaceTypeSpecify the Electrical Interface Type:
V.24 - V.24 Electrical Interface Type
V.35 - V.35 Electrical Interface Type
V.36 - V.36 Electrical Interface Type
X.21 - X.21 Electrical Interface Type
NONE - Electrically disabledro Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.23.1.21 |
cdx6500TCOPCfgV24ElectricalInterfaceOptionSpecify the Pin 22 option:
RI - V.24 uses Pin 22 for Ring Indicator output signal
TM - V.24 uses Pin 22 for Test Mode input signalro Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.23.1.22 |
cdx6500TCOPCfgHighSpeedElectricalInterfaceOptionSpecify the cable type:
NONE - V.35/V.36/X.21 DCE with straight through cable
XOVER - V.35/V.36/X.21 DCE with crossover adapter cablero Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.23.1.23 |
cdx6500Statistics OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.3 |
cdx6500StatProtocolGroup OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.3.1 |
cdx6500PSTPortProtocolGroup OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.3.1.1 |
cdx6500PPSTTCOPPortTableThis table holds statistics items for TCOP ports. SEQUENCE OF Cdx6500PPSTTCOPPortEntry .1.3.6.1.4.1.449.2.1.3.1.1.24 |
cdx6500PPSTTCOPPortEntryThis entry holds the statistics items for one TCOP port. Cdx6500PPSTTCOPPortEntry .1.3.6.1.4.1.449.2.1.3.1.1.24.1 |
cdx6500TCOPStatPortNumberThe port number for this TCOP entry.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.24.1.1 |
cdx6500TCOPStatPortTypeThe configured value of the Port Type.ro Enumeration .1.3.6.1.4.1.449.2.1.3.1.1.24.1.2 |
cdx6500TCOPStatPortSubtypeAccess protocol for this port.
hsc3 - Transparent Hitachi type
gnet - Transparent GNET type.
uts - Transparent Uniscope type.
slc - Synchronous Link Control.
ac100 - AC100.ro Enumeration .1.3.6.1.4.1.449.2.1.3.1.1.24.1.3 |
cdx6500TCOPStatPortStatusStatus of this port:
Up : Port is enabled
Down : Port is Inactive
Disabled : Port is disabled.ro DisplayString .1.3.6.1.4.1.449.2.1.3.1.1.24.1.4 |
cdx6500TCOPStatPortStateCurrent port state:
discPhase - Disconnect phase, no call in place
callingPhase - Port has initiated Autocall
calledPhase - Port has received a call request
connected - Connection has been established.ro Enumeration .1.3.6.1.4.1.449.2.1.3.1.1.24.1.5 |
cdx6500TCOPStatPortSpeedThe measured port speed in bits per second.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.24.1.6 |
cdx6500TCOPStatPortUtilInPercentage of port bandwidth in use.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.24.1.7 |
cdx6500TCOPStatPortUtilOutPercentage of port bandwidth in use.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.24.1.8 |
cdx6500TCOPStatPortOverrunErrsTotal number of overrun errors counted by the I/O
driver since the last node or statistics reset.ro Counter16 .1.3.6.1.4.1.449.2.1.3.1.1.24.1.9 |
cdx6500TCOPStatPortUnderrunErrsTotal number of underrun errors counted by the I/O
driver since the last node or statistics reset.ro Counter16 .1.3.6.1.4.1.449.2.1.3.1.1.24.1.10 |
cdx6500TCOPStatPortBCCErrsTotal number of CRC errors counted by the I/O
driver since the last node or statistics reset.ro Counter16 .1.3.6.1.4.1.449.2.1.3.1.1.24.1.11 |
cdx6500TCOPStatPortParityErrsTotal number of parity errors counted by the I/O
driver since the last node or statistics reset.ro Counter16 .1.3.6.1.4.1.449.2.1.3.1.1.24.1.12 |
cdx6500TCOPStatPortInCharsNumber of characters received since last node,
port or statistics reset.ro Counter .1.3.6.1.4.1.449.2.1.3.1.1.24.1.13 |
cdx6500TCOPStatPortOutCharsNumber of characters sent since last node,
port or statistics reset.ro Counter .1.3.6.1.4.1.449.2.1.3.1.1.24.1.14 |
cdx6500TCOPStatPortInCharsRateAverage number of characters received per second
since last node, port or statistics reset.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.24.1.15 |
cdx6500TCOPStatPortOutCharsRateAverage number of characters sent per second
since last node, port or statistics reset.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.24.1.16 |
cdx6500TCOPStatPortInMessagesNumber of messages received since last node,
port or statistics reset.ro Counter .1.3.6.1.4.1.449.2.1.3.1.1.24.1.17 |
cdx6500TCOPStatPortOutMessagesNumber of messages sent since last node,
port or statistics reset.ro Counter .1.3.6.1.4.1.449.2.1.3.1.1.24.1.18 |
cdx6500TCOPStatPortInMessagesRateAverage number of messages received per second
since last node, port or statistics reset.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.24.1.19 |
cdx6500TCOPStatPortOutMessagesRateAverage number of messages sent per second
since last node, port or statistics reset.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.24.1.20 |
cdx6500TCOPStatPortInPktsQueuedNumber of received packets which are currently queued.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.24.1.21 |
cdx6500TCOPStatPortOutPktsQueuedNumber of packets currently queued which are to be sent.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.24.1.22 |
cdx6500TCOPStatPortMaxInQueueLengthThe maximum queue length reached for incoming
packets since the last reset.ro Gauge .1.3.6.1.4.1.449.2.1.3.1.1.24.1.23 |
cdx6500TCOPStatPortMaxOutQueueLengthThe maximum queue length reached since
the last reset, for packets to be sent.ro Gauge .1.3.6.1.4.1.449.2.1.3.1.1.24.1.24 |
cdx6500TCOPStatPortPktQueueFlushCountThe number of times the receive queue is flushed.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.24.1.25 |
cdx6500TCOPStatAutoCallStatusCurrent status of the autocall.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.24.1.26 |
cdx6500TCOPStatAutoCallNextAttemptTime in seconds until next autocall attempt.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.24.1.27 |
cdx6500TCOPStatAutoCallAttemptCountNumber of autocall attempts.ro Counter .1.3.6.1.4.1.449.2.1.3.1.1.24.1.28 |
cdx6500TCOPStatAutoCallLastClearCauseLast autocall clear cause code
dte - Cleared by other end
np - Destination not obtainable
occ - Called number busy
nc - Network congested
inv - Invalid facility requested
na - Access barred
err - Local procedure error
rpe - Remote procedure error
der - Called number out of order
rna - Reverse charging not accepted
roo - RPOA out of order
icd - Incompatible destination
fsn - Fast select acceptance not subscribed
ctp - Control port intervention
sha - Ship absent.ro Enumeration .1.3.6.1.4.1.449.2.1.3.1.1.24.1.29 |
cdx6500TCOPStatAutoCallLastClearDiagnosisLast clear diagnostic code
none - No more information
bps - Invalid P(S)
bpr - Invalid P(R)
ptinv - Packet type invalid
pna - Packet not allowed
psh - Packet too short
pln - Packet too long
tout - Timer expired
tcli - Timer expired for clear indication
nocs - Call set-up problem
nofc - Facility/registration code not allowed
nofp - Facility/registration parameter not allowed
cald - Bad called address
cali - Bad calling address
invfl - Invalid facilities length
icb - Incoming call barred
nolcn - No logical channel available
cco - Call collision occurred
dupl - Duplicate facility requested
nadl - Non-zero address length
nfcl - Non-zero facility length
nfce - Facility not found when expected
trp - Temporary routing problem
clin - Call limit reached on intermediate node
cldn - Call limit reached on destination node
ncil - No logical channel available on internode link
ccpo - Call cleared by Control Port operator
csld - Call setup looping detected
cshe - Call setup hop count exceeded
finl - Failure on intermediate node link
rin3 - Restart received at level 3
disc - DISC received at level 2
dm - DM received at level 2
sabm - SABM received at level 2
frmr - FRMR received at level 2
invnr - Invalid N(R)
unsf - Unsolicited F bit received
ucmd - Unknown command received
uresp - Unknown response received
gtcap - I field too long
t1to - T1/N2 timeout
frlen - Received frame of incorrect size
aderr - Address error
spbo - Source port is in Busy Out state
dpbo - Destination port is in Busy Out state
srr - Session reconnection rejected.ro Enumeration .1.3.6.1.4.1.449.2.1.3.1.1.24.1.30 |
cdx6500TCOPStatAutoCallLastInCalledAddressX25 called address in BCD format of last inbound call.ro DisplayString .1.3.6.1.4.1.449.2.1.3.1.1.24.1.31 |
cdx6500TCOPStatAutoCallLastInCallingAddressX25 calling address in BCD format of last inbound call.ro DisplayString .1.3.6.1.4.1.449.2.1.3.1.1.24.1.32 |
cdx6500TCOPStatAutoCallLastInCallFacilitiesX25 facilities of inbound call.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.24.1.33 |
cdx6500TCOPStatAutoCallLastInCallCUDX25 Call User Data of inbound call.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.24.1.34 |
cdx6500TCOPStatAutoCallLastOutCalledAddressX25 called address in BCD format of last outbound call.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.24.1.35 |
cdx6500TCOPStatAutoCallLastOutCallingAddressX25 calling address in BCD format of last outbound call.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.24.1.36 |
cdx6500TCOPStatAutoCallLastOutCallFacilitiesX25 facilities of outbound call.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.24.1.37 |
cdx6500TCOPStatAutoCallLastOutCallCUDX25 Call User Data of outbound call.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.24.1.38 |
cdx6500Controls OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.4 |