SS-OPT-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
49
Objects
Active
Status
2
Dependencies
Imported Objects
Objects
49 total| Object Name |
|---|
codex OBJECT IDENTIFIER .1.3.6.1.4.1.449 |
RFC1155-SMI Unknown .1.3.6.1.4.1.449 |
cdxProductSpecific OBJECT IDENTIFIER .1.3.6.1.4.1.449.2 |
cdx6500 OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1 |
cdx6500Configuration OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.2 |
cdx6500CfgGeneralGroup OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.2.2 |
cdx6500GCTLSSTableA list of Configuration parameters that makeup
the Switched Service/LBU Table. SEQUENCE OF Cdx6500SSCfgEntry .1.3.6.1.4.1.449.2.1.2.2.14 |
cdx6500SSCfgEntryEach entry contains the Configuration parameters for
each switched Service/backup link. Cdx6500SSCfgEntry .1.3.6.1.4.1.449.2.1.2.2.14.1 |
cdx6500SSEntryNumberThis identifies the particular Switched Service/LBU
Table entry being configured. The number of instances
defined by this entry depends on the configured value
of the Maximum Switch Service Entry parameter in the
Node record (upto a maximum of 1024 entries). If this
value is 0, no switched Service/backup links may be
configured i.e. this table will be empty.ro INTEGER .1.3.6.1.4.1.449.2.1.2.2.14.1.1 |
cdx6500SSDestinationNameThis is a unique name that identifies this entry.ro DisplayString .1.3.6.1.4.1.449.2.1.2.2.14.1.2 |
cdx6500SSCfgMonitoredPortThe X.25 port to be monitored for link failure.
This is the port whose calls are rerouted in
the event of port failure. The format must be the
following: X25-n, FRI-nSm OR BRI-nCp
where n is the port number, m is the station number
and p is BRI channel number.ro DisplayString .1.3.6.1.4.1.449.2.1.2.2.14.1.3 |
cdx6500SSCfgRestoralPortThis is the port or channel that acts as the backup
when there is a port failure on the port
specified by the parameter Monitored port, or primary
destination port (activated by call)
The format must be the following:
X25-n or BRI-nCm,
where n is the port number and m is the channel number.ro DisplayString .1.3.6.1.4.1.449.2.1.2.2.14.1.4 |
cdx6500SSDialSequenceThis specifies the telephone numbers that
will be dialed when the backup port is activated.
To enter your own telephone number, use any
combination of the following characters:
0-9 Decimal
: Wait Tone
< Pause
= Seperator 3
> Seperator 4
P or p Dialing to be continued in PULSE mode.
T or t Dialing to be continued in DTMF mode.
& Flash
To have the modem dial one of its pre-programmed
telephone numbers, enter:
#n where 'n' identifies the pre-programmed
telephone number stored in the modem.ro DisplayString .1.3.6.1.4.1.449.2.1.2.2.14.1.5 |
cdx6500SSActivationModeThis specifies how the switched service/backup port
will be activated.
fail - Activate the backup port upon link failure.
call - Activate the backup port upon a call request.
either - Activate the backup port upon link
failure or a call request.
newvalFail - same functionality as 'fail', new enumeration
added for RFC1155 compatibility.ro Enumeration .1.3.6.1.4.1.449.2.1.2.2.14.1.6 |
cdx6500SSDeactivationModeThis specifies how the switched service/backup port is
deactivated after the original link is up.
none - Backup port can only be deactivated
by operator intervention.
busyOut - The backup port is deactivated after
all the calls on that port are cleared
for a predetermined amount of time.
This substitutes the value assigned
to the parameter Link Hold Time with
the value assigned to the parameter
Idle Disconnect Time in the X.25 Port
Record. The Idle Disconnect Time will
then work as described in the Operators
Guide.
When Deactivation Mode = BUSY OUT and
Link Hold Time = 0 (zero) the overall
effect is the same as setting this
entry to NONE.
imm - The backup link is terminated
IMMediately when the monitored port is
restored regardless of how many calls
are present.
newvalNone - same functionality as 'none', new enumeration
added for RFC1155 compatibility.ro Enumeration .1.3.6.1.4.1.449.2.1.2.2.14.1.7 |
cdx6500SSLinkHoldTimeThis replaces the value of the parameter Idle
Disconnect Timer in the X.25 Port Record and
specifies how long (in seconds) the backup link
remains active after the original link is back up.ro INTEGER .1.3.6.1.4.1.449.2.1.2.2.14.1.8 |
cdx6500SSOutBoundPassThis is the password used by the remote station to
determine if dial access is authorized.ro DisplayString .1.3.6.1.4.1.449.2.1.2.2.14.1.9 |
cdx6500SSRedialTimeThis is the time in seconds between dial attempts when
bringing up a switched service call.ro INTEGER .1.3.6.1.4.1.449.2.1.2.2.14.1.10 |
cdx6500SSRedialCounterThis parameter is used to specify the number of times
that the Switched Service will attempt to redial when
redial timer is expired. A value of zero will allow
unlimited attempts.ro INTEGER .1.3.6.1.4.1.449.2.1.2.2.14.1.11 |
cdx6500SSSecurityModeThis specifies under what conditions the port/channel
authorizes call request.
none - A call request not be rejected based on password
of calling party id validation.
password - A call request will only be accepted if the
password it provides matches the switched
services password configured in the node
record.
callingId - A call request will only be accepted if
the calling party id of the caller matches
one of the entries found in the calling
party id table.
both - A call request is accepted only if both the
password and the calling party id are valid.
newvalNone - same functionality as 'none', new enumeration
added for RFC1155 compatibility.ro Enumeration .1.3.6.1.4.1.449.2.1.2.2.14.1.12 |
cdx6500SSSetupTimeThis is the time in seconds the monitor port(s) are given
to come up after node boot before the backup port is
activated.ro INTEGER .1.3.6.1.4.1.449.2.1.2.2.14.1.13 |
cdx6500SSCfgMonitoredPort2The X.25 port to be monitored for link failure.
This is the port whose calls are rerouted in
the event of port failure. The format must be the
following: X25-n, FRI-nSm OR BRI-nCp
where n is the port number, m is the station number
and p is BRI channel number.ro DisplayString .1.3.6.1.4.1.449.2.1.2.2.14.1.14 |
cdx6500SSCfgMonitoredPort3The X.25 port to be monitored for link failure.
This is the port whose calls are rerouted in
the event of port failure. The format must be the
following: X25-n, FRI-nSm OR BRI-nCp
where n is the port number, m is the station number
and p is BRI channel number.ro DisplayString .1.3.6.1.4.1.449.2.1.2.2.14.1.15 |
cdx6500SSCfgMonitoredPort4The X.25 port to be monitored for link failure.
This is the port whose calls are rerouted in
the event of port failure. The format must be the
following: X25-n, FRI-nSm OR BRI-nCp
where n is the port number, m is the station number
and p is BRI channel number.ro DisplayString .1.3.6.1.4.1.449.2.1.2.2.14.1.16 |
cdx6500SSDialSequence2This specifies the telephone numbers that
will be dialed when the backup port is activated.
To enter your own telephone number, use any
combination of the following characters:
0-9 Decimal
: Wait Tone
< Pause
= Seperator 3
> Seperator 4
P or p Dialing to be continued in PULSE mode.
T or t Dialing to be continued in DTMF mode.
& Flash
To have the modem dial one of its pre-programmed
telephone numbers, enter:
#n where 'n' identifies the pre-programmed
telephone number stored in the modem.ro DisplayString .1.3.6.1.4.1.449.2.1.2.2.14.1.17 |
cdx6500SSDialSequence3This specifies the telephone numbers that
will be dialed when the backup port is activated.
To enter your own telephone number, use any
combination of the following characters:
0-9 Decimal
: Wait Tone
< Pause
= Seperator 3
> Seperator 4
P or p Dialing to be continued in PULSE mode.
T or t Dialing to be continued in DTMF mode.
& Flash
To have the modem dial one of its pre-programmed
telephone numbers, enter:
#n where 'n' identifies the pre-programmed
telephone number stored in the modem.ro DisplayString .1.3.6.1.4.1.449.2.1.2.2.14.1.18 |
cdx6500SSDialSequence4This specifies the telephone numbers that
will be dialed when the backup port is activated.
To enter your own telephone number, use any
combination of the following characters:
0-9 Decimal
: Wait Tone
< Pause
= Seperator 3
> Seperator 4
P or p Dialing to be continued in PULSE mode.
T or t Dialing to be continued in DTMF mode.
& Flash
To have the modem dial one of its pre-programmed
telephone numbers, enter:
#n where 'n' identifies the pre-programmed
telephone number stored in the modem.ro DisplayString .1.3.6.1.4.1.449.2.1.2.2.14.1.19 |
cdx6500CallIDTableA list of Configuration calling ID that makeup the
Calling ID Table. SEQUENCE OF Cdx6500CallIDEntry .1.3.6.1.4.1.449.2.1.2.2.18 |
cdx6500CallIDEntryEach entry contains the Configuration Calling ID. Cdx6500CallIDEntry .1.3.6.1.4.1.449.2.1.2.2.18.1 |
cdx6500CallIDEntryNumberThis is not a configurable parameter.
This identifies the particular calling ID
Table entry being configured by the other
parameters in the record.ro INTEGER .1.3.6.1.4.1.449.2.1.2.2.18.1.1 |
cdx6500CallIDStringEach calling id entry is a numeric value which may
contain periods or dashes. Only calls matching these
ids will be allowed when calling id security is
enabled.ro DisplayString .1.3.6.1.4.1.449.2.1.2.2.18.1.2 |
cdx6500Statistics OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.3 |
cdx6500StatOtherStatsGroup OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.3.2 |
cdx6500OSTSSTableA list of statistics parameters for the Switch Service/Link
Backup port,station,and channel. SEQUENCE OF Cdx6500SSStatEntry .1.3.6.1.4.1.449.2.1.3.2.3 |
cdx6500SSStatEntryEach entry on this table pertains to the Switched
Service/Link Backup port,station and channel, and
can be accessed using the following index:
the switched/backup port number, switched/backup
station number and the switched/backup channel number. Cdx6500SSStatEntry .1.3.6.1.4.1.449.2.1.3.2.3.1 |
cdx6500SSStatRestoralPortThis is the backup port number, used as an index
to access Switched Service/LBU statistics.ro INTEGER .1.3.6.1.4.1.449.2.1.3.2.3.1.1 |
cdx6500SSPortTypeThe port type of the backup port.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.2.3.1.2 |
cdx6500SSConnTypeThe connection type of the backup port.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.2.3.1.3 |
cdx6500SSStatusThe status of the backup port.
newvalDown - same functionality as 'down', new
enumeration added for RFC1155 compatibility.ro Enumeration .1.3.6.1.4.1.449.2.1.3.2.3.1.4 |
cdx6500SSReasonThe reason that the backup port is active.
none : Backup port is deactivated.
call : A call request was made on the backup port.
fail : Due to a link failure on the monitored port.
remote : A call request was made to the backup port.
ctp : Backup port was activated from the control terminal.
newvalNone : same functionality as 'none', new
enumeration added for RFC1155 compatibility.ro Enumeration .1.3.6.1.4.1.449.2.1.3.2.3.1.5 |
cdx6500SSRedialThis parameter is used to specify the number of times
that the Switched Service will attempt to redial when
the redial timer is expired. A value of zero will
allow unlimited attempts.ro INTEGER .1.3.6.1.4.1.449.2.1.3.2.3.1.6 |
cdx6500SSLastActivatedThe last time the backup port was activated.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.2.3.1.7 |
cdx6500SSLastPhoneDialedThe phone number dialed the last time the
backup port was activated.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.2.3.1.8 |
cdx6500OSTSSMonTableA list of statistics parameters for the Link Backup's
monitored port. SEQUENCE OF Cdx6500SSMonStatEntry .1.3.6.1.4.1.449.2.1.3.2.4 |
cdx6500SSMonStatEntryEach entry on this table pertains to one of the monitored
ports/station/channel that is monitored by the backup port/
station/channel and should be accessed using the
following index,
* the backup port number
* the backup station number
* the backup channel number
* the monitored port
* the monitored station
* the monitored channel. Cdx6500SSMonStatEntry .1.3.6.1.4.1.449.2.1.3.2.4.1 |
cdx6500SSStatRestMonPortThis is the backup port number, used as a
primary index to access monitored port statistics.ro INTEGER .1.3.6.1.4.1.449.2.1.3.2.4.1.1 |
cdx6500SSStatMonitoredPortThis is the port being monitored by the backup port,
used as a secondary index to access monitored port
statistics.ro INTEGER .1.3.6.1.4.1.449.2.1.3.2.4.1.2 |
cdx6500SSMonPortStateState of the monitored port.
newvalDown : same functionality as 'down', new enumeration
added for RFC1155 compatibility.ro Enumeration .1.3.6.1.4.1.449.2.1.3.2.4.1.3 |
cdx6500SSRestPhoneNumPhone number that the backup port will dial when a
monitored port has a link failure.ro DisplayString .1.3.6.1.4.1.449.2.1.3.2.4.1.4 |