SOFTWIRE-MESH-MIB
This MIB module contains managed object definitions for the softwire mesh framework. Copyright (c) 2016 IETF Trust and the persons identified as authors of the code. All rights reserved. Redistribution and use in source and binary forms, with or without modification, is permitted pursuant to, and subject to the license terms contained in, the Simplified BSD License set forth in Section 4.c of the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info).
Main OID:
swmMIB.1.3.6.1.2.1.239
24
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
24 total| Object Name |
|---|
swmMIBThis MIB module contains managed object definitions for the softwire mesh framework. Copyright (c) 2016 IETF Trust and the persons identified as authors of the code. All rights reserved. Redistribution and use in source and binary forms, with or without modification, is permitted pursuant to, and subject to the license terms contained in, the Simplified BSD License set forth in Section 4.c of the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info). MODULE-IDENTITY .1.3.6.1.2.1.239 |
swmObjects OBJECT IDENTIFIER .1.3.6.1.2.1.239.1 |
swmSupportedTunnelTableA table of objects that show what kinds of tunnels can be supported by the AFBR. SEQUENCE OF SwmSupportedTunnelEntry .1.3.6.1.2.1.239.1.1 |
swmSupportedTunnelEntryA set of objects that show what kinds of tunnels can be supported in the AFBR. If the AFBR supports multiple tunnel types, the swmSupportedTunnelTable would have several entries. SwmSupportedTunnelEntry .1.3.6.1.2.1.239.1.1.1 |
swmSupportedTunnelTypeRepresents the tunnel type that can be used for softwire mesh scenarios, such as L2TPv3 over IP, GRE, Transmit tunnel endpoint, IPsec in Tunnel-mode, IP in IP tunnel with IPsec Transport Mode, MPLS-in-IP tunnel with IPsec Transport Mode, and IP in IP. There is no restriction on the tunnel type the softwire mesh can use.ro IANAtunnelType (IANAifType-MIB) .1.3.6.1.2.1.239.1.1.1.1 |
swmEncapsTableA table of objects that display the softwire mesh encapsulation information. SEQUENCE OF SwmEncapsEntry .1.3.6.1.2.1.239.1.2 |
swmEncapsEntryA table of objects that manage the softwire mesh I-IP encapsulation destination based on the E-IP destination prefix. SwmEncapsEntry .1.3.6.1.2.1.239.1.2.1 |
swmEncapsEIPDstTypeThis object specifies the address type used for swmEncapsEIPDst. It is different from the tunnelIfAddressType in the tunnelIfTable. The swmEncapsEIPDstType is IPv6 (2) if it is IPv6-over-IPv4 tunneling. The swmEncapsEIPDstType is IPv4 (1) if it is IPv4-over-IPv6 tunneling. InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.2.1.239.1.2.1.1 |
swmEncapsEIPDstThe E-IP destination prefix, which is used for I-IP encapsulation destination looking up. The type of this address is determined by the value of swmEncapsEIPDstType InetAddress (INET-ADDRESS-MIB) .1.3.6.1.2.1.239.1.2.1.2 |
swmEncapsEIPPrefixLengthThe prefix length of the E-IP destination prefix. InetAddressPrefixLength (INET-ADDRESS-MIB) .1.3.6.1.2.1.239.1.2.1.3 |
swmEncapsIIPDstTypeThis object specifies the address type used for swmEncapsIIPDst. It is the same as the tunnelIfAddressType in the tunnelIfTable.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.2.1.239.1.2.1.4 |
swmEncapsIIPDstThe I-IP destination address, which is used as the encapsulation destination for the corresponding E-IP prefix. Since the tunnelIfRemoteInetAddress in the tunnelIfTable should be 0.0.0.0 or ::, swmEncapIIPDst should be the destination address used in the outer IP header.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.2.1.239.1.2.1.5 |
swmBGPNeighborTableA table of objects that display the softwire mesh BGP neighbor information. SEQUENCE OF SwmBGPNeighborEntry .1.3.6.1.2.1.239.1.3 |
swmBGPNeighborEntryA set of objects that display the softwire mesh BGP neighbor information. SwmBGPNeighborEntry .1.3.6.1.2.1.239.1.3.1 |
swmBGPNeighborInetAddressTypeThis object specifies the address type used for swmBGPNeighborInetAddress. InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.2.1.239.1.3.1.1 |
swmBGPNeighborInetAddressThe address of the AFBR's BGP neighbor. The address type is the same as the tunnelIfAddressType in the tunnelIfTable. InetAddress (INET-ADDRESS-MIB) .1.3.6.1.2.1.239.1.3.1.2 |
swmBGPNeighborTunnelTypeRepresents the type of tunnel that the AFBR chooses to transmit traffic with another AFBR/BGP neighbor.ro IANAtunnelType (IANAifType-MIB) .1.3.6.1.2.1.239.1.3.1.3 |
swmConformance OBJECT IDENTIFIER .1.3.6.1.2.1.239.2 |
swmCompliances OBJECT IDENTIFIER .1.3.6.1.2.1.239.2.1 |
swmComplianceDescribes the requirements for conformance to the Softwire Mesh MIB. The following index objects cannot be added as OBJECT clauses but nevertheless have compliance requirements: Unknown .1.3.6.1.2.1.239.2.1.1 |
swmGroups OBJECT IDENTIFIER .1.3.6.1.2.1.239.2.2 |
swmSupportedTunnelGroupThe collection of objects that are used to show what kind of tunnel the AFBR supports. Unknown .1.3.6.1.2.1.239.2.2.1 |
swmEncapsGroupThe collection of objects that are used to display softwire mesh encapsulation information. Unknown .1.3.6.1.2.1.239.2.2.2 |
swmBGPNeighborGroupThe collection of objects that are used to display softwire mesh BGP neighbor information. Unknown .1.3.6.1.2.1.239.2.2.3 |