RoamAbout-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for RoamAbout-MIB.
95
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
95 total| Object Name |
|---|
dec OBJECT IDENTIFIER .1.3.6.1.4.1.36 |
RFC1155-SMI Unknown .1.3.6.1.4.1.36 |
ema OBJECT IDENTIFIER .1.3.6.1.4.1.36.2 |
decMIBextension OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18 |
roamabout OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.35 |
rabtPCCardTypeThe type of PC card inserted in the Access Point.ro Enumeration .1.3.6.1.4.1.36.2.18.35.1 |
rabtIPAddressStateDetermines the state of IP Address storage.
A value of 2 causes the current IP address
to be stored in NVRAM.rw Enumeration .1.3.6.1.4.1.36.2.18.35.2 |
rabtBridgeModeCURRENT Access Point bridge mode state. LAN-to-LAN mode is
the improved name for 802.11. LAN-to-LAN used to be called
full-bridge pre-802.11.rw Enumeration .1.3.6.1.4.1.36.2.18.35.3 |
rabtUplineDumpModeDetermines whether or not a dump file
is created on an Access Point crash.rw Enumeration .1.3.6.1.4.1.36.2.18.35.4 |
rabtMemorySizeThe size of the memory in the Access Point in Mbytes.ro INTEGER .1.3.6.1.4.1.36.2.18.35.5 |
rabtUpgradeFlashCauses the Access Point to attempt a flash upgrade.
Be aware that this causes the Access Point to reset.rw Enumeration .1.3.6.1.4.1.36.2.18.35.6 |
rabtForceUplineDumpCauses the Access Point to attempt a upline dump.
Be aware that this causes the Access Point to reset.rw Enumeration .1.3.6.1.4.1.36.2.18.35.7 |
rabtStationNameThe wireless station name sent out as part of
the beacon messages. Valid only when a DS card
is inserted in the Access Point.rw DisplayString .1.3.6.1.4.1.36.2.18.35.8 |
rabtIPSubnetMaskThe IP subnet mask for this access Point.rw IpAddress .1.3.6.1.4.1.36.2.18.35.9 |
rabtDSChannelThe channel number for the wireless non-IEEE 2400DS card.
This value is only valid currently if a 2400DS card
is installed. After changing this value, it will not
be loaded onto the card until reset is performed.rw Enumeration .1.3.6.1.4.1.36.2.18.35.10 |
rabtDSCountryVariantDescribes the country variant of the 2400DS card.
This value is only valid currently if a 2400DS card
is installed.ro Enumeration .1.3.6.1.4.1.36.2.18.35.11 |
rabtDSCurrentNWIDThe WaveLAN Network ID (NWID) this RF-modem
is currently operating with.ro OCTET STRING .1.3.6.1.4.1.36.2.18.35.12 |
rabtEncryptionEnableUsed to enable or disable encryption of the wireless radio
signals if the installed PC Card supports encryption, and
the Access Point is in the 'trusted' security mode. After
changing this value, it will not be loaded onto the card
until reset is performed.
This value varies from wliEncSelect in that it shows the
future value of the encryption mode after the next reset,
and wliEncSelect is read-only.
If the Access Point is in the 'non-trusted' security mode,
this parameter cannot be set via SNMP, only through the
console port.rw Enumeration .1.3.6.1.4.1.36.2.18.35.13 |
rabtPTPDiag OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.35.14 |
rabtPTPRemoteStationMACThe MAC address for the remote station to participate
in the Point-to-Point diagnostic test.
To initiate a search for a participating station, write the
broadcast address (FF-FF-FF-FF-FF-FF) to this variable.rw PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.36.2.18.35.14.1 |
rabtPTPRemoteStationNameThe wireless station name of the remote station
participating in the Point-to-Point diagnostic test.ro DisplayString .1.3.6.1.4.1.36.2.18.35.14.2 |
rabtPTPRemoteSignalLevelThe last remote signal level value obtained from the
Point-to-Point diagnostic test.
A value of 0 is returned if the last sample was not valid.ro INTEGER .1.3.6.1.4.1.36.2.18.35.14.3 |
rabtPTPRemoteNoiseLevelThe last remote noise level value obtained from the
Point-to-Point diagnostic test.
A value of 0 is returned if the last sample was not valid.ro INTEGER .1.3.6.1.4.1.36.2.18.35.14.4 |
rabtPTPRemoteSignalQualityThe last remote signal quality value obtained from the
Point-to-Point diagnostic test.
A value of 0 is returned if the PTP Diagnostic testing is
not currently active.ro INTEGER .1.3.6.1.4.1.36.2.18.35.14.5 |
rabtPTPIntervalWriting a 1 to this variable causes a single PTP sample to
be performed.rw INTEGER .1.3.6.1.4.1.36.2.18.35.14.6 |
rabtPTPLocalSignalLevelThe last LOCAL Signal Level value obtained from the
Point-to-Point diagnostic test.
A value of 0 is returned if the last sample was not valid.ro INTEGER .1.3.6.1.4.1.36.2.18.35.14.7 |
rabtPTPLocalNoiseLevelThe last LOCAL Noise Level value obtained from the
Point-to-Point diagnostic test.
A value of 0 is returned if the last sample was not valid.ro INTEGER .1.3.6.1.4.1.36.2.18.35.14.8 |
rabtPTPLocalSignalQualityThe last LOCAL signal quality value obtained from the
Point-to-Point diagnostic test.
A value of 0 is returned if the last sample was not valid.ro INTEGER .1.3.6.1.4.1.36.2.18.35.14.9 |
rabtDot11 OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.35.15 |
rabtDot11Current OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.35.15.1 |
rabtDot11CurrentChannelThe CURRENT channel.ro INTEGER .1.3.6.1.4.1.36.2.18.35.15.1.1 |
rabtDot11CurrentNetworkNameThe CURRENT network name.ro DisplayString .1.3.6.1.4.1.36.2.18.35.15.1.2 |
rabtDot11CurrentStationNameDefines the CURRENT station name of the radio interface,
used by client utilities.ro DisplayString .1.3.6.1.4.1.36.2.18.35.15.1.3 |
rabtDot11CurrentOperationalRateThis attribute shall specify the set of data rates
at which the station may transmit data. Each octet
contains a value representing a rate. Each rate
shall be within the range from 2 to 127,
corresponding to data rates in increments of
500 kb/s from 1 Mb/s to 63.5 Mb/s, and shall be
supported (as indicated in the supported rates
table) for receiving data. This value is reported in
transmitted Beacon, Probe Request, Probe Response,
Association Request, Association Response,
Reassociation Request, and Reassociation Response
frames, and is used to determine whether a BSS
with which the station desires to synchronize is
suitable. It is also used when starting a BSS,
as specified in 10.3.ro OCTET STRING .1.3.6.1.4.1.36.2.18.35.15.1.4 |
rabtDot11CurrentSystemScaleSpecifies the CURRENT Access Point density in the ESS.ro Enumeration .1.3.6.1.4.1.36.2.18.35.15.1.5 |
rabtDot11CurrentDTIMPeriodDefines the CURRENT number of beacon intervals between
successive DTIMs.ro INTEGER .1.3.6.1.4.1.36.2.18.35.15.1.6 |
rabtDot11CurrentFragmentationThresholdThis attribute shall specify the mandatory maximum size, in
octets, of the MPDU that may be delivered to the PHY. An MSDU
shall be broken into fragments if its size exceeds the value
of this attribute after adding MAC headers and trailers. An MSDU
or MMPDU shall be fragmented when the resulting frame has an
individual address in the Address1 field, and the length of the
frame is larger than this threshold. The default value for this
attribute shall be the lesser of 2346 or the aMPDUMaxLength of
the attached PHY and shall never exceed the lesser of 2346 or
the aMPDUMaxLength of the attached PHY. The value of this
attribute shall never be less than 256.ro INTEGER .1.3.6.1.4.1.36.2.18.35.15.1.7 |
rabtDot11CurrentRTSThresholdThis attribute shall indicate the number of octets in an MPDU,
below which an RTS/CTS handshake shall not be performed. An
RTS/CTS handshake shall be performed at the beginning of any
frame exchange sequence where the MPDU is of type Data or
Management, the MPDU has an individual address in the Address1
field, and the length of the MPDU is greater than
this threshold. (For additional details, refer to Table 21 in
9.7.) Setting this attribute to be larger than the maximum
MSDU size shall have the effect of turning off the RTS/CTS
handshake for frames of Data or Management type transmitted by
this STA. Setting this attribute to zero shall have the effect
of turning on the RTS/CTS handshake for all frames of Data or
Management type transmitted by this STA. The default value of
this attribute shall be 2347.ro INTEGER .1.3.6.1.4.1.36.2.18.35.15.1.8 |
rabtDot11CurrentMulticastPMBufferingDefines if multicast MAC frames are CURRENTLY buffered for
transmission after DTIM. If disabled, MAC frames are
immediately placed in the output queue for transmission.ro Enumeration .1.3.6.1.4.1.36.2.18.35.15.1.9 |
rabtDot11CurrentSecureAccessWhen this mode is set to enabled, the AP will only associate
with stations that have the same network name as the AP.
When this mode is set to disabled, a station with the
network name of ANY is allowed to associate.ro Enumeration .1.3.6.1.4.1.36.2.18.35.15.1.10 |
rabtDot11CurrentTransmitRateThis value specifies the transmission rate of the AP. It is
implemented when cards that operate faster than the 2Mbit
802.11 standard are inserted.ro Enumeration .1.3.6.1.4.1.36.2.18.35.15.1.11 |
rabtDot11CurrentPrivacyInvokedWhen this attribute is true, it shall indicate that the AP
is currently using the 802.11 WEP mechanism for transmitting
frames of type Data.ro Enumeration .1.3.6.1.4.1.36.2.18.35.15.1.12 |
rabtDot11CurrentExcludeUnencryptedThis value indicates the current setting of the dot11ExcludeUnencrypted
attribute in the AP.ro Enumeration .1.3.6.1.4.1.36.2.18.35.15.1.13 |
rabtDot11Future OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.35.15.2 |
rabtDot11FutureChannelDefines the FUTURE channel (communication frequency) to be
used for creating a BSS.
Note that different subsets of channels are valid for
different registration domains. The current domain can be
found at dot11CurrentRegDomain. The valid channels per
domain are listed in the IEEE 802.11 specification. Setting
an invalid channel will result in a SNMP BAD-VALUE error.
The term future means that a change takes effect after the
next reset of the Access Point. The current channel can be
obtained from dot11CurrentChannel.rw INTEGER .1.3.6.1.4.1.36.2.18.35.15.2.1 |
rabtDot11FutureNetworkNameDefines the FUTURE Service Set IDentifier to be used for the
BSS.
The term future means that a change takes effect after the
next reset of the Access Point. The current BSSID can be
obtained from dot11DesiredSSID.rw DisplayString .1.3.6.1.4.1.36.2.18.35.15.2.2 |
rabtDot11FutureStationNameDefines the FUTURE station name of the radio interface,
used by client utilities.
The term future means that a change takes effect after the
next reset of the Access Point. The current station name
can be read from rabtStationName.rw DisplayString .1.3.6.1.4.1.36.2.18.35.15.2.3 |
rabtDot11FutureOperationalRateThis attribute shall specify the set of data rates
at which the station may transmit data. Each octet
contains a value representing a rate. Each rate
shall be within the range from 2 to 127,
corresponding to data rates in increments of
500 kb/s from 1 Mb/s to 63.5 Mb/s, and shall be
supported (as indicated in the supported rates
table) for receiving data. This value is reported in
transmitted Beacon, Probe Request, Probe Response,
Association Request, Association Response,
Reassociation Request, and Reassociation Response
frames, and is used to determine whether a BSS
with which the station desires to synchronize is
suitable. It is also used when starting a BSS,
as specified in 10.3.rw OCTET STRING .1.3.6.1.4.1.36.2.18.35.15.2.4 |
rabtDot11FutureSystemScaleSpecifies the FUTURE Access Point density in the ESS.
The term future means that the change takes effect after the
next reset of the Access Point. The current system scale is
found above at rabtDot11CurrentSystemScale.rw Enumeration .1.3.6.1.4.1.36.2.18.35.15.2.5 |
rabtDot11FutureDTIMPeriodDefines the FUTURE number of beacon intervals between
successive DTIMs.
The term future means that a change takes effect after the
next reset of the Access Point. The current DTIM period
is at dot11DTIMPeriod.rw INTEGER .1.3.6.1.4.1.36.2.18.35.15.2.6 |
rabtDot11FutureFragmentationThresholdThis attribute shall specify the mandatory maximum size, in
octets, of the MPDU that may be delivered to the PHY. An MSDU
shall be broken into fragments if its size exceeds the value
of this attribute after adding MAC headers and trailers. An MSDU
or MMPDU shall be fragmented when the resulting frame has an
individual address in the Address1 field, and the length of the
frame is larger than this threshold. The default value for this
attribute shall be the lesser of 2346 or the aMPDUMaxLength of
the attached PHY and shall never exceed the lesser of 2346 or
the aMPDUMaxLength of the attached PHY. The value of this
attribute shall never be less than 256.rw INTEGER .1.3.6.1.4.1.36.2.18.35.15.2.7 |
rabtDot11FutureRTSThresholdThis attribute shall indicate the number of octets in an MPDU,
below which an RTS/CTS handshake shall not be performed. An
RTS/CTS handshake shall be performed at the beginning of any
frame exchange sequence where the MPDU is of type Data or
Management, the MPDU has an individual address in the Address1
field, and the length of the MPDU is greater than
this threshold. (For additional details, refer to Table 21 in
9.7.) Setting this attribute to be larger than the maximum
MSDU size shall have the effect of turning off the RTS/CTS
handshake for frames of Data or Management type transmitted by
this STA. Setting this attribute to zero shall have the effect
of turning on the RTS/CTS handshake for all frames of Data or
Management type transmitted by this STA. The default value of
this attribute shall be 2347.rw INTEGER .1.3.6.1.4.1.36.2.18.35.15.2.8 |
rabtDot11FutureMulticastPMBufferingDefines if multicast MAC frames are to be buffered for
transmission after DTIM in the FUTURE. If disabled, MAC
frames will be immediately placed in the output queue for
transmission.
The term future means that a change takes effect after the
next reset of the Access Point. The current multicast PM
buffering state is read from
rabtDot11CurrentMulticastPMBuffering.rw Enumeration .1.3.6.1.4.1.36.2.18.35.15.2.9 |
rabtDot11FutureSecureAccessWhen this mode is set to enabled, the AP will only associate
with stations that have the same network name as the AP.
When this mode is set to disabled, a station with the
network name of ANY is allowed to associate.
The term future means that a change takes effect after the
next reset of the Access Point. The current multicast PM
buffering state is read from
rabtDot11CurrentMulticastPMBuffering.rw Enumeration .1.3.6.1.4.1.36.2.18.35.15.2.10 |
rabtDot11FutureTransmitRateThis value specifies the transmission rate of the AP. It is
implemented when cards that operate faster than the 2Mbit
802.11 standard are inserted.rw Enumeration .1.3.6.1.4.1.36.2.18.35.15.2.11 |
rabtDot11FuturePrivacyInvokedThis value specifies the future setting of the
dot11PrivacyInvoked attribute in the AP.rw Enumeration .1.3.6.1.4.1.36.2.18.35.15.2.12 |
rabtDot11FutureExcludeUnencryptedThis value specifies the future value of the
dot11ExcludeUnencrypted attribute in the AP.rw Enumeration .1.3.6.1.4.1.36.2.18.35.15.2.13 |
rabtDot11General OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.35.15.3 |
rabtDot11PCCardVersionsSpecifies the version identifiers for the PC card.ro DisplayString .1.3.6.1.4.1.36.2.18.35.15.3.1 |
rabtDot11Bldg OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.35.15.4 |
rabtDot11BldgRemoteMACThe CURRENT MAC address for the remote station participating
in a 802.11 Building-to-Building link.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.36.2.18.35.15.4.1 |
rabtDot11FutureBldgRemoteMACThe FUTURE MAC address for the remote station participating
in a 802.11 Building-to-Building link.
Setting this MAC address and then ISSUING A RESET
places the AP in the Building-to-Building mode.rw PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.36.2.18.35.15.4.2 |
rabtFutureBridgeModeFUTURE Access Point bridge mode state. LAN-to-LAN mode is
the improved name for 802.11. LAN-to-LAN used to be called
full-bridge pre-802.11. pre-802.11 was dynamic. It now
requires a reset to implement.rw Enumeration .1.3.6.1.4.1.36.2.18.35.15.4.3 |
rabtDot11BldgExt OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.35.15.4.4 |
rabtDot11BldgExtCurrent OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.35.15.4.4.1 |
rabtDot11BldgRelayModeEnabling relay mode allows the Access Point in a point to
multi-point configuration to relay broadcast messages to
other wireless AP's.rw Enumeration .1.3.6.1.4.1.36.2.18.35.15.4.4.1.1 |
rabtDot11BldgRemoteMAC2The CURRENT MAC address for the remote station participating
in a 802.11 Building-to-Building link.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.36.2.18.35.15.4.4.1.2 |
rabtDot11BldgRemoteMAC3The CURRENT MAC address for the remote station participating
in a 802.11 Building-to-Building link.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.36.2.18.35.15.4.4.1.3 |
rabtDot11BldgRemoteMAC4The CURRENT MAC address for the remote station participating
in a 802.11 Building-to-Building link.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.36.2.18.35.15.4.4.1.4 |
rabtDot11BldgRemoteMAC5The CURRENT MAC address for the remote station participating
in a 802.11 Building-to-Building link.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.36.2.18.35.15.4.4.1.5 |
rabtDot11BldgRemoteMAC6The CURRENT MAC address for the remote station participating
in a 802.11 Building-to-Building link.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.36.2.18.35.15.4.4.1.6 |
rabtDot11BldgExtFuture OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.35.15.4.4.2 |
rabtDot11BldgFutureRelayModeEnabling relay mode allows the Access Point in a point to
multi-point configuration to relay broadcast messages to
other wireless AP's.rw Enumeration .1.3.6.1.4.1.36.2.18.35.15.4.4.2.1 |
rabtDot11BldgFutureRemoteMAC2The FUTURE MAC address for the remote station participating
in a 802.11 Building-to-Building link.rw PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.36.2.18.35.15.4.4.2.2 |
rabtDot11BldgFutureRemoteMAC3The FUTURE MAC address for the remote station participating
in a 802.11 Building-to-Building link.rw PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.36.2.18.35.15.4.4.2.3 |
rabtDot11BldgFutureRemoteMAC4The FUTURE MAC address for the remote station participating
in a 802.11 Building-to-Building link.rw PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.36.2.18.35.15.4.4.2.4 |
rabtDot11BldgFutureRemoteMAC5The FUTURE MAC address for the remote station participating
in a 802.11 Building-to-Building link.rw PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.36.2.18.35.15.4.4.2.5 |
rabtDot11BldgFutureRemoteMAC6The FUTURE MAC address for the remote station participating
in a 802.11 Building-to-Building link.rw PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.36.2.18.35.15.4.4.2.6 |
rabtDot11WEP OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.35.15.5 |
rabtDot11WEPEnhancedImplementedThis value indicates whether the AP is capable of Enhanced
Wireless Equivalent Privacy (WEP), using 128-bit keys.ro Enumeration .1.3.6.1.4.1.36.2.18.35.15.5.1 |
rabtDot11WEPExcludeSNMPThis value indicates that SNMP management of WEP attributes
is disabled in the AP.ro Enumeration .1.3.6.1.4.1.36.2.18.35.15.5.2 |
rabtdot11KeyStateTableA conceptual table containing a set of booleans
identifying if an encryption key has been set or not. SEQUENCE OF RabtDot11KeyStateEntry .1.3.6.1.4.1.36.2.18.35.15.5.3 |
rabtdot11KeyStateEntryAn Entry (conceptual row) in the Key State Table.
ifIndex - Each 802.11 interface is represented by an
ifEntry. Interface tables in this MIB module are indexed
by ifIndex. RabtDot11KeyStateEntry .1.3.6.1.4.1.36.2.18.35.15.5.3.1 |
rabtdot11KeyStateIndexThe auxiliary variable used to identify instances
of the columnar objects in the Key State Table. INTEGER .1.3.6.1.4.1.36.2.18.35.15.5.3.1.1 |
rabtDot11KeyStateThe state column used for determining if an
encryption key is set or not.ro Enumeration .1.3.6.1.4.1.36.2.18.35.15.5.3.1.2 |
roamaboutLoader OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.35.16 |
rabtFirmwareUseBootpControls where the AccessPoint gets the information that
it needs to download new firmware.
When true(1), indicates that the AP should use the BootP
protocol to auto-configure parameters such as its own IP
address, gateway IP, subnet, TFTP server IP address, and
file name.
When false(2), indicates that the AccessPoint should use
locally-configured parameters stored in NVRAM.rw Enumeration .1.3.6.1.4.1.36.2.18.35.16.1 |
rabtFirmwareServerIPThe IP address of the TFTP server that should be used for
firmware downloads.
This value will be ignored when 'rabtFirmwareUseBootp' is
'false(2)'.rw IpAddress .1.3.6.1.4.1.36.2.18.35.16.2 |
rabtFirmwareFilenameThe name of the remote file that contains the firmware to
be downloaded.
This value will be ignored when 'rabtFirmwareUseBootp' is
'false(2)'.rw OCTET STRING( 0..128 ) .1.3.6.1.4.1.36.2.18.35.16.3 |
rabtFirmwareStatusIndicates the success or failure of the AccessPoint's most
recent attempt to download new firmware. In the case of a
failure, the value of this object may provide some clue as
to what caused the failure.
This MIB object does not distinguish 'managment-initiated'
reloads from reloads that the AccessPoint initiates.ro Enumeration .1.3.6.1.4.1.36.2.18.35.16.4 |
rabtCrashUploadUseBootpControls where the AccessPoint gets the information that
it needs to upload crash dumps.
When true(1), indicates that the AP should use the BootP
protocol to auto-configure parameters such as its own IP
address, gateway IP, subnet, TFTP server IP address, and
directory name.
When false(2), indicates that the AccessPoint should use
locally-configured parameters stored in NVRAM.rw Enumeration .1.3.6.1.4.1.36.2.18.35.16.5 |
rabtCrashUploadServerIPThe IP address of the TFTP server that should be used for
crash dump uploads.
This value will be ignored when 'rabtCrashUploadUseBootp'
is 'false(2)'.rw IpAddress .1.3.6.1.4.1.36.2.18.35.16.6 |
rabtCrashUploadDirectoryThe name of the remote directory to which all crash dumps
should be uploaded.
This value will be ignored when 'rabtCrashUploadUseBootp'
is 'false(2)'.rw OCTET STRING( 0..128 ) .1.3.6.1.4.1.36.2.18.35.16.7 |
roamaboutConsole OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.35.17 |
rabtUseConsolePasswordIndicates whether the AccessPoint console (command line
interface) should be password-protected.
------------------------ NOTE -------------------------
Currently, password protection won't take effect unless
the read-write community string is something OTHER than
'public'. This could change, though it's unlikely.
-------------------------------------------------------rw Enumeration .1.3.6.1.4.1.36.2.18.35.17.1 |