RS-232-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for RS-232-MIB.
59
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
59 total| Object Name |
|---|
rs232 OBJECT IDENTIFIER .1.3.6.1.2.1.10.33 |
SNMPv2-SMI-v1 Unknown .1.3.6.1.2.1.10.33 |
rs232NumberThe number of ports (regardless of their current
state) in the RS-232-like general port table.ro Integer32 .1.3.6.1.2.1.10.33.1 |
rs232PortTableA list of port entries. The number of entries is
given by the value of rs232Number. SEQUENCE OF Rs232PortEntry .1.3.6.1.2.1.10.33.2 |
rs232PortEntryStatus and parameter values for a port. Rs232PortEntry .1.3.6.1.2.1.10.33.2.1 |
rs232PortIndexThe value of ifIndex for the port. By convention
and if possible, hardware port numbers map directly
to external connectors. The value for each port must
remain constant at least from one re-initialization
of the network management agent to the next.ro InterfaceIndex -- Rsyntax Integer32 .1.3.6.1.2.1.10.33.2.1.1 |
rs232PortTypeThe port's hardware type.ro Enumeration .1.3.6.1.2.1.10.33.2.1.2 |
rs232PortInSigNumberThe number of input signals for the port in the
input signal table (rs232PortInSigTable). The table
contains entries only for those signals the software
can detect and that are useful to observe.ro Integer32 .1.3.6.1.2.1.10.33.2.1.3 |
rs232PortOutSigNumberThe number of output signals for the port in the
output signal table (rs232PortOutSigTable). The
table contains entries only for those signals the
software can assert and that are useful to observe.ro Integer32 .1.3.6.1.2.1.10.33.2.1.4 |
rs232PortInSpeedThe port's input speed in bits per second. Note that
non-standard values, such as 9612, are probably not allowed
on most implementations.rw Integer32 .1.3.6.1.2.1.10.33.2.1.5 |
rs232PortOutSpeedThe port's output speed in bits per second. Note that
non-standard values, such as 9612, are probably not allowed
on most implementations.rw Integer32 .1.3.6.1.2.1.10.33.2.1.6 |
rs232PortInFlowTypeThe port's type of input flow control. 'none'
indicates no flow control at this level.
'ctsRts' and 'dsrDtr' indicate use of the indicated
hardware signals.rw Enumeration .1.3.6.1.2.1.10.33.2.1.7 |
rs232PortOutFlowTypeThe port's type of output flow control. 'none'
indicates no flow control at this level.
'ctsRts' and 'dsrDtr' indicate use of the indicated
hardware signals.rw Enumeration .1.3.6.1.2.1.10.33.2.1.8 |
rs232AsyncPortTableA list of asynchronous port entries. Entries need
not exist for synchronous ports. SEQUENCE OF Rs232AsyncPortEntry .1.3.6.1.2.1.10.33.3 |
rs232AsyncPortEntryStatus and parameter values for an asynchronous
port. Rs232AsyncPortEntry .1.3.6.1.2.1.10.33.3.1 |
rs232AsyncPortIndexA unique value for each port. Its value is the
same as rs232PortIndex for the port.ro InterfaceIndex -- Rsyntax Integer32 .1.3.6.1.2.1.10.33.3.1.1 |
rs232AsyncPortBitsThe port's number of bits in a character.rw INTEGER .1.3.6.1.2.1.10.33.3.1.2 |
rs232AsyncPortStopBitsThe port's number of stop bits.rw Enumeration .1.3.6.1.2.1.10.33.3.1.3 |
rs232AsyncPortParityThe port's sense of a character parity bit.rw Enumeration .1.3.6.1.2.1.10.33.3.1.4 |
rs232AsyncPortAutobaudA control for the port's ability to automatically
sense input speed.
When rs232PortAutoBaud is 'enabled', a port may
autobaud to values different from the set values for
speed, parity, and character size. As a result a
network management system may temporarily observe
values different from what was previously set.rw Enumeration .1.3.6.1.2.1.10.33.3.1.5 |
rs232AsyncPortParityErrsTotal number of characters with a parity error,
input from the port since system re-initialization
and while the port state was 'up' or 'test'.ro Counter32 .1.3.6.1.2.1.10.33.3.1.6 |
rs232AsyncPortFramingErrsTotal number of characters with a framing error,
input from the port since system re-initialization
and while the port state was 'up' or 'test'.ro Counter32 .1.3.6.1.2.1.10.33.3.1.7 |
rs232AsyncPortOverrunErrsTotal number of characters with an overrun error,
input from the port since system re-initialization
and while the port state was 'up' or 'test'.ro Counter32 .1.3.6.1.2.1.10.33.3.1.8 |
rs232SyncPortTableA list of asynchronous port entries. Entries need
not exist for synchronous ports. SEQUENCE OF Rs232SyncPortEntry .1.3.6.1.2.1.10.33.4 |
rs232SyncPortEntryStatus and parameter values for a synchronous
port. Rs232SyncPortEntry .1.3.6.1.2.1.10.33.4.1 |
rs232SyncPortIndexA unique value for each port. Its value is the
same as rs232PortIndex for the port.ro InterfaceIndex -- Rsyntax Integer32 .1.3.6.1.2.1.10.33.4.1.1 |
rs232SyncPortClockSourceSource of the port's bit rate clock. 'split' means
the transmit clock is internal and the receive clock
is external.rw Enumeration .1.3.6.1.2.1.10.33.4.1.2 |
rs232SyncPortFrameCheckErrsTotal number of frames with an invalid frame check
sequence, input from the port since system
re-initialization and while the port state was 'up'
or 'test'.ro Counter32 .1.3.6.1.2.1.10.33.4.1.3 |
rs232SyncPortTransmitUnderrunErrsTotal number of frames that failed to be
transmitted on the port since system
re-initialization and while the port state was 'up'
or 'test' because data was not available to the
transmitter in time.ro Counter32 .1.3.6.1.2.1.10.33.4.1.4 |
rs232SyncPortReceiveOverrunErrsTotal number of frames that failed to be received
on the port since system re-initialization and while
the port state was 'up' or 'test' because the
receiver did not accept the data in time.ro Counter32 .1.3.6.1.2.1.10.33.4.1.5 |
rs232SyncPortInterruptedFramesTotal number of frames that failed to be received
or transmitted on the port due to loss of modem
signals since system re-initialization and while the
port state was 'up' or 'test'.ro Counter32 .1.3.6.1.2.1.10.33.4.1.6 |
rs232SyncPortAbortedFramesNumber of frames aborted on the port due to
receiving an abort sequence since system
re-initialization and while the port state was 'up'
or 'test'.ro Counter32 .1.3.6.1.2.1.10.33.4.1.7 |
rs232SyncPortRoleThe role the device is playing that is using this port.
dte means the device is performing the role of
data terminal equipment
dce means the device is performing the role of
data circuit-terminating equipment.rw Enumeration .1.3.6.1.2.1.10.33.4.1.8 |
rs232SyncPortEncodingThe bit stream encoding technique that is in effect
for this port.
nrz for Non-Return to Zero encoding
nrzi for Non-Return to Zero Inverted encoding.rw Enumeration .1.3.6.1.2.1.10.33.4.1.9 |
rs232SyncPortRTSControlThe method used to control the Request To Send (RTS)
signal.
controlled when the DTE is asserts RTS each time
data needs to be transmitted and drops
RTS at some point after data
transmission begins.
If rs232SyncPortRole is 'dte', the
RTS is an output signal. The device
will issue a RTS and wait for a CTS
from the DCE before starting to
transmit.
If rs232SyncPortRole is 'dce', the
RTS is an input signal. The device
will issue a CTS only after having
received RTS and waiting the
rs232SyncPortRTSCTSDelay interval.
constant when the DTE constantly asserts RTS.rw Enumeration .1.3.6.1.2.1.10.33.4.1.10 |
rs232SyncPortRTSCTSDelayThe interval (in milliseconds) that the DCE must wait
after it sees RTS asserted before asserting CTS. This
object exists in support of older synchronous devices
that cannot recognize CTS within a certain interval
after it asserts RTS.rw Integer32 .1.3.6.1.2.1.10.33.4.1.11 |
rs232SyncPortModeThe mode of operation of the port with respect to the
direction and simultaneity of data transfer.
fdx when frames on the data link can be
transmitted and received at the same
time
hdx when frames can either be received
from the data link or transmitted
onto the data link but not at the
same time.
simplex-receive when frames can only be received on
this data link.
simplex-send when frames can only be sent on this
data link.rw Enumeration .1.3.6.1.2.1.10.33.4.1.12 |
rs232SyncPortIdlePatternThe bit pattern used to indicate an idle line.rw Enumeration .1.3.6.1.2.1.10.33.4.1.13 |
rs232SyncPortMinFlagsThe minimum number of flag patterns this port needs in
order to recognize the end of one frame and the start
of the next. Plausible values are 1 and 2.rw Integer32 .1.3.6.1.2.1.10.33.4.1.14 |
rs232InSigTableA list of port input control signal entries
implemented and visible to the software on the port,
and useful to monitor. SEQUENCE OF Rs232InSigEntry .1.3.6.1.2.1.10.33.5 |
rs232InSigEntryInput control signal status for a hardware port. Rs232InSigEntry .1.3.6.1.2.1.10.33.5.1 |
rs232InSigPortIndexThe value of rs232PortIndex for the port to which
this entry belongs.ro InterfaceIndex -- Rsyntax Integer32 .1.3.6.1.2.1.10.33.5.1.1 |
rs232InSigNameIdentification of a hardware signal, as follows:
rts Request to Send
cts Clear to Send
dsr Data Set Ready
dtr Data Terminal Ready
ri Ring Indicator
dcd Received Line Signal Detector
sq Signal Quality Detector
srs Data Signaling Rate Selector
srts Secondary Request to Send
scts Secondary Clear to Send
sdcd Secondary Received Line Signal Detectorro Enumeration .1.3.6.1.2.1.10.33.5.1.2 |
rs232InSigStateThe current signal state.ro Enumeration .1.3.6.1.2.1.10.33.5.1.3 |
rs232InSigChangesThe number of times the signal has changed from
'on' to 'off' or from 'off' to 'on'.ro Counter32 .1.3.6.1.2.1.10.33.5.1.4 |
rs232OutSigTableA list of port output control signal entries
implemented and visible to the software on the port,
and useful to monitor. SEQUENCE OF Rs232OutSigEntry .1.3.6.1.2.1.10.33.6 |
rs232OutSigEntryOutput control signal status for a hardware port. Rs232OutSigEntry .1.3.6.1.2.1.10.33.6.1 |
rs232OutSigPortIndexThe value of rs232PortIndex for the port to which
this entry belongs.ro InterfaceIndex -- Rsyntax Integer32 .1.3.6.1.2.1.10.33.6.1.1 |
rs232OutSigNameIdentification of a hardware signal, as follows:
rts Request to Send
cts Clear to Send
dsr Data Set Ready
dtr Data Terminal Ready
ri Ring Indicator
dcd Received Line Signal Detector
sq Signal Quality Detector
srs Data Signaling Rate Selector
srts Secondary Request to Send
scts Secondary Clear to Send
sdcd Secondary Received Line Signal Detectorro Enumeration .1.3.6.1.2.1.10.33.6.1.2 |
rs232OutSigStateThe current signal state.ro Enumeration .1.3.6.1.2.1.10.33.6.1.3 |
rs232OutSigChangesThe number of times the signal has changed from
'on' to 'off' or from 'off' to 'on'.ro Counter32 .1.3.6.1.2.1.10.33.6.1.4 |
rs232Conformance OBJECT IDENTIFIER .1.3.6.1.2.1.10.33.7 |
rs232Groups OBJECT IDENTIFIER .1.3.6.1.2.1.10.33.7.1 |
rs232Group OBJECT IDENTIFIER .1.3.6.1.2.1.10.33.7.1.1 |
rs232AsyncGroup OBJECT IDENTIFIER .1.3.6.1.2.1.10.33.7.1.2 |
rs232SyncGroup OBJECT IDENTIFIER .1.3.6.1.2.1.10.33.7.1.3 |
rs232SyncSDLCGroup OBJECT IDENTIFIER .1.3.6.1.2.1.10.33.7.1.4 |
rs232Compliances OBJECT IDENTIFIER .1.3.6.1.2.1.10.33.7.2 |
rs232Compliance OBJECT IDENTIFIER .1.3.6.1.2.1.10.33.7.2.1 |