ROSMGMT-OPTICAL-TRANSCEIVER-MIB
AI MIB Summary
The ROSMGMT-OPTICAL-TRANSCEIVER-MIB enables SNMP-based monitoring of optical transceiver parameters, including received/transmitted optical power, laser bias current, temperature, and supply voltage, on MikroTik RouterOS network elements. This module provides granular visibility into the physical layer health of SFP/SFP+ modules to facilitate proactive fault detection and link degradation analysis.
This MIB module defines objects to monitor optical characteristics on the optical interfaces in a network element.
Main OID:
rosMgmtOpticalTransceiver.18
141
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
141 total| Object Name |
|---|
rosMgmtOpticalTransceiverThis MIB module defines objects to monitor optical
characteristics on the optical interfaces in a network element. MODULE-IDENTITY .18 |
rosMgmtOpticalTransceiverNotifications OBJECT IDENTIFIER .18.0 |
rosMgmtOpticalTransceiverAbsentTrapThis notification is sent when the optical module is removed from the device.
This notification may be suppressed under the following
conditions:
- depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. NOTIFICATION-TYPE .18.0.1 |
rosMgmtOpticalTransceiverPresentTrapThis notification is sent when the optical module is plugged into the device.
This notification may be suppressed under the following
conditions:
- depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. NOTIFICATION-TYPE .18.0.2 |
rosMgmtOpticalTransceiverNRAlarmTrapThis notification is sent when the transmitted or received data of optical module is invalid.
This notification may be suppressed under the following
conditions:
- depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. NOTIFICATION-TYPE .18.0.3 |
rosMgmtOpticalTransceiverNRNormalTrapThis notification is sent when the transmitted or received data of optical module is valid.
This notification may be suppressed under the following
conditions:
- depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. NOTIFICATION-TYPE .18.0.4 |
rosMgmtOpticalTransceiverRxLosAlarmTrapThis notification is sent when the optical module receiving signal is lost.
This notification may be suppressed under the following
conditions:
- depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. NOTIFICATION-TYPE .18.0.5 |
rosMgmtOpticalTransceiverRxLosNormaTrapThis notification is sent when the optical module receiving signal is back to normal.
This notification may be suppressed under the following
conditions:
- depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. NOTIFICATION-TYPE .18.0.6 |
rosMgmtOpticalTransceiverParamAlarmTrapThis notification is sent when the optical module parameter value increase to above
the high alarm threshold or dicrease to under the low alarm threshold.
This notification may be suppressed under the following
conditions:
- depending on the value of the rosMgmtOpticalNotifyEnable and rosMgmtOpticalPortNotifyEnable objects. NOTIFICATION-TYPE .18.0.7 |
rosMgmtOpticalTransceiverParamAlarmNormalTrapThis notification is sent when the optical module parameter value dicrease to
under the high alarm threshold or increase to above the low alarm threshold.
This notification may be suppressed under the following
conditions:
- depending on the value of the rosMgmtOpticalNotifyEnable and rosMgmtOpticalPortNotifyEnable objects. NOTIFICATION-TYPE .18.0.8 |
rosMgmtOpticalTransceiverParamWarningTrapThis notification is sent when the optical module parameter value increase to above
the high warning threshold or dicrease to under the low warning threshold.
This notification may be suppressed under the following
conditions:
- depending on the value of the rosMgmtOpticalNotifyEnable and rosMgmtOpticalPortNotifyEnable objects. NOTIFICATION-TYPE .18.0.9 |
rosMgmtOpticalTransceiverParamWarningNormalTrapThis notification is sent when the optical module parameter value dicrease to
under the high warning threshold or increase to above the low warning threshold.
This notification may be suppressed under the following
conditions:
- depending on the value of the rosMgmtOpticalNotifyEnable and rosMgmtOpticalPortNotifyEnable objects. NOTIFICATION-TYPE .18.0.10 |
rosMgmtOpticalTransceiverLaserBackLightAlarmTrapThis notification is sent when the optical module password cheching is successful.
This notification may be suppressed under the following
conditions:
- depending on the value of the rosMgmtOpticalNotifyEnable and rosMgmtOpticalPortNotifyEnable objects. NOTIFICATION-TYPE .18.0.11 |
rosMgmtOpticalTransceiverLaserBackLightAlarmNormalTrapThis notification is sent when the optical module password cheching is successful.
This notification may be suppressed under the following
conditions:
- depending on the value of the rosMgmtOpticalNotifyEnable and rosMgmtOpticalPortNotifyEnable objects. NOTIFICATION-TYPE .18.0.12 |
rosMgmtOpticalTransceiverLaserLifeAlarmTrapThis notification is sent when the optical module password cheching is successful.
This notification may be suppressed under the following
conditions:
- depending on the value of the rosMgmtOpticalNotifyEnable and rosMgmtOpticalPortNotifyEnable objects. NOTIFICATION-TYPE .18.0.13 |
rosMgmtOpticalTransceiverLaserLifeAlarmNormalTrapThis notification is sent when the optical module password cheching is successful.
This notification may be suppressed under the following
conditions:
- depending on the value of the rosMgmtOpticalNotifyEnable and rosMgmtOpticalPortNotifyEnable objects. NOTIFICATION-TYPE .18.0.14 |
rosMgmtOpticalTransceiverParamLowAlarmTrapThis notification is sent when the optical module parameter value increase to above
the high alarm threshold or dicrease to under the low alarm threshold.
This notification may be suppressed under the following
conditions:
- depending on the value of the rosMgmtOpticalNotifyEnable and rosMgmtOpticalPortNotifyEnable objects. NOTIFICATION-TYPE .18.0.15 |
rosMgmtOpticalTransceiverParamLowAlarmNormalTrapThis notification is sent when the optical module parameter value increase to above
the high alarm threshold or dicrease to under the low alarm threshold.
This notification may be suppressed under the following
conditions:
- depending on the value of the rosMgmtOpticalNotifyEnable and rosMgmtOpticalPortNotifyEnable objects. NOTIFICATION-TYPE .18.0.16 |
rosMgmtOpticalTransceiverParamLowWarningTrapThis notification is sent when the optical module parameter value increase to above
the high alarm threshold or dicrease to under the low alarm threshold.
This notification may be suppressed under the following
conditions:
- depending on the value of the rosMgmtOpticalNotifyEnable and rosMgmtOpticalPortNotifyEnable objects. NOTIFICATION-TYPE .18.0.17 |
rosMgmtOpticalTransceiverParamLowWarningNormalTrapThis notification is sent when the optical module parameter value increase to above
the high alarm threshold or dicrease to under the low alarm threshold.
This notification may be suppressed under the following
conditions:
- depending on the value of the rosMgmtOpticalNotifyEnable and rosMgmtOpticalPortNotifyEnable objects. NOTIFICATION-TYPE .18.0.18 |
rosMgmtOpticalTransceiverTxFaultTrapThis notification is sent when the SFP optical module occures Tx-fault signal.
This notification may be suppressed under the following
conditions:
- depending on the value of the rosMgmtOpticalNotifyEnable and rosMgmtOpticalPortNotifyEnable objects. NOTIFICATION-TYPE .18.0.19 |
rosMgmtOpticalTransceiverTxNormalTrapThis notification is sent when the SFP optical module cancels the Tx-fault signal.
This notification may be suppressed under the following
conditions:
- depending on the value of the rosMgmtOpticalNotifyEnable and rosMgmtOpticalPortNotifyEnable objects. NOTIFICATION-TYPE .18.0.20 |
rosMgmtOpticalTransceiverObjects OBJECT IDENTIFIER .18.1 |
rosMgmtOpticalTransceiverScalarGroup OBJECT IDENTIFIER .18.1.1 |
rosMgmtOpticalTransceiverNotifyEnableThis object specifies the generation of device notifications,
enable or disable.
this object belongs to xfp and sfp.rw EnableVar .18.1.1.1 |
rosMgmtOpticalTransceiverDDMEnableEnable or disable digitaldiagnotic on the device.
this object belongs to xfp and sfp.rw EnableVar .18.1.1.2 |
rosMgmtOpticalTransceiverCheckPwdEnableThis object specifies the status of password checking on the device,
enable or disable.
this object belongs to xfp.rw EnableVar .18.1.1.3 |
rosMgmtOpticalTransceiverPollIntervalThis object specifies the value of poll-interval on the device.
this object belongs to xfp and sfp.rw Integer32 .18.1.1.4 |
rosMgmtOpticalTransceiverCRCCheckEnableThis object specifies the status of crc checking on the device,
enable or disable.
this object belongs to sfp and xfp.rw EnableVar .18.1.1.5 |
rosMgmtOpticalTransceiverCfgObjects OBJECT IDENTIFIER .18.1.2 |
rosMgmtOpticalTransceiverInfoGroup OBJECT IDENTIFIER .18.1.2.1 |
rosMgmtOpticalTransceiverInfoTableTrancetver information Table. SEQUENCE OF RosMgmtOpticalTransceiverInfoEntry .18.1.2.1.1 |
rosMgmtOpticalTransceiverInfoEntryAn entry in the rosMgmtOpticalTransceiverInfoTable. RosMgmtOpticalTransceiverInfoEntry .18.1.2.1.1.1 |
rosMgmtOpticalTransceiverTypeThis object specifies the physical type of the transceiver,
such as xfp or sfp , and so on.
this object belongs to xfp and sfp.ro Enumeration .18.1.2.1.1.1.1 |
rosMgmtOpticalTransceiverConnectorTypeThis object specifies the connector type of the transceiver,
unknown, sc, db9, hssdc, bnc_tnc, fiber_coaxial_head, fiber_outlet,
lc, mt_rj, mu, sg, fiber_pigtail, mpo_parallel_optic , hssdcII,
copper, rj45.
this object belongs to xfp and sfp.ro Enumeration .18.1.2.1.1.1.2 |
rosMgmtOpticalTransceiverVendorNameVendor name of the interface.
this object belongs to xfp and sfp.ro OCTET STRING .18.1.2.1.1.1.3 |
rosMgmtOpticalTransceiverVendorPNVendor part number of the interface.
this object belongs to xfp and sfp.ro OCTET STRING .18.1.2.1.1.1.4 |
rosMgmtOpticalTransceiverVendorSNVendor serial number of the interface.
this object belongs to xfp and sfp.ro OCTET STRING .18.1.2.1.1.1.5 |
rosMgmtOpticalTransceiverMediaTypeTypes of the fiber,
single_mode, multi_modeE50, multi_mode50,multi_mode625,copper,
single_modeKm,multi_modeOM3,multi_modeOM3Qsfp,multi_modeOM2Qsfp,
multi_modeOM1Qsfp,multi_modeOM4Qsfp.
this object belongs to xfp, sfp and qsfp.ro Enumeration .18.1.2.1.1.1.6 |
rosMgmtOpticalTransceiverTransmissionDistanceThe max distance which the interface could transmit,
measured in meter.
The object will be shown in unit of Km, and the precision is 0.001.
this object belongs to xfp and sfp.ro Integer32 .18.1.2.1.1.1.7 |
rosMgmtOpticalTransceiverAbilityThis object specifies the ability of optical module digitaldiagnotic
funtion. Currently, the digitaldiagnotic objects of our optical module
inculde 16 parameters.
this object has 32 bits, each bit represents a digital diagnotic parameter.
if the bit value is 0, it means that the optical module does not provide
digital diagnotic funtion for relative parameter.if the bit value is 1,it
means that the optical module provides digital diagnotic funtion for
relative parameter.
this object belongs to xfp and sfp.
The relation between parameters and bits is following:
32...16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1:
The relation between parameters and bits is following:
32...16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1:
| 1bit | 2bit | 3bit | 4bit
| APD Bias voltage | 0(reserve) | TEC Current | Laser temperature
| 5bit | 6bit |7bit | 8bit
| Laser wavelength | +5V Supply voltage | +3.3V Supply voltage | +1.8V Supply voltage
| 9bit | 10bit |11bit | 12bit
| -5.2V Supply voltage | +5V Supply current | 0(None) | 0(None)
| 13bit | 14bit | 15bit | 16bit
| +3.3V Supply current | +1.8V Supply current | -5.2V Supply current | temperature
| 17bit | 18bit | 19bit | 20bit ~ 32bit
| Laser bias current | Rx power |Tx power | 0
But when the optical module is sfp, the 6 bit will represents
the supplyVoltage of sfp.ro Unsigned32 .18.1.2.1.1.1.8 |
rosMgmtOpticalTransceiverDDMThis object specifies if the transceiver supports on digital diagnostic function,
support or not support.To the xfp, the default value of this object is support.
this object belongs to xfp and sfp.ro Enumeration .18.1.2.1.1.1.9 |
rosMgmtOpticalTransceiverCalibrationTypeThis object specifies the calibration type of the transceiver,
internal, external, unknown.
this object belongs to xfp and sfp.ro Enumeration .18.1.2.1.1.1.10 |
rosMgmtOpticalTransceiverRSSIThis object specifies the calibration type of the transceiver,
support or not support.
this object belongs to xfp and sfp.ro Enumeration .18.1.2.1.1.1.11 |
rosMgmtOpticalTransceiverVendorRevthe version number of the transceiver.
this object belongs to xfp and sfp.ro OCTET STRING .18.1.2.1.1.1.12 |
rosMgmtOpticalTransceiverBRMaxthe min data rate of the transceiver,mesured in Mbps .
this object belongs to xfp and sfp.
The object will be shown in unit of Gbps, and the precision is 0.1.ro Integer32 .18.1.2.1.1.1.13 |
rosMgmtOpticalTransceiverBRMinthe min data rate of the transceiver,mesured in Mbps.
this object belongs to xfp and sfp.To the sfp,
the min data rate value is equal to the max data rate value.
The object will be shown in unit of Gbps, and the precision is 0.1.ro Integer32 .18.1.2.1.1.1.14 |
rosMgmtOpticalTransceiverWavelengthContrlif the transceiver supports on wavelength control
support,notsupport.
this object belongs to xfp.ro Enumeration .18.1.2.1.1.1.15 |
rosMgmtOpticalTransceiverWavelengthWavelength of the interface, measured in pm(0.001nm).
this object belongs to xfp.
The object will be shown in unit of nm, and the precision is 0.01.ro Integer32 .18.1.2.1.1.1.16 |
rosMgmtOpticalTransceiverWaveTolerancethe range of laser wavelength from nominal wavelength,mesured in pm(0.001*nm).
this object belongs to xfp.
The object will be shown in unit of nm, and the precision is 0.01.ro Integer32 .18.1.2.1.1.1.17 |
rosMgmtOpticalTransceiverCompatibilitythe compatibility type that the transceiver supports,such as 10GBASE-SR.
this object belongs to xfp.ro OCTET STRING .18.1.2.1.1.1.18 |
rosMgmtOpticalTransceiverPowerDissipationthe max power dissipation of the transceiver,
p1W5,p2W5,p3W5,exceed3W5.
this object belongs to xfp.ro Enumeration .18.1.2.1.1.1.19 |
rosMgmtOpticalTransceiverCDRthe optical module supports on CDR fundtion.
support,notsupport.
this object belongs to xfp.ro Enumeration .18.1.2.1.1.1.20 |
rosMgmtOpticalTransceiverRefClockif the transceiver requires outside reference clock
required,notrequired.
this object belongs to xfp.ro Enumeration .18.1.2.1.1.1.21 |
rosMgmtOpticalTransceiverTransmitterTypeThe transmitter type of the transceiver,such as 850 nm VCSEL.
this object belongs to xfp.ro Enumeration .18.1.2.1.1.1.22 |
rosMgmtOpticalTransceiverCooledThe transmitter cooled type of the transceiver
cooled,uncooled.
this object belongs to xfp.ro Enumeration .18.1.2.1.1.1.24 |
rosMgmtOpticalTransceiverTunalbeThe transmitter tunable type of the transceiver
tunable,untunable.
this object belongs to xfp.ro Enumeration .18.1.2.1.1.1.25 |
rosMgmtOpticalTransceiverDetectorTypeThe detector type of the transceiver
pin, apd.
this object belongs to xfp.ro Enumeration .18.1.2.1.1.1.26 |
rosMgmtOpticalTransceiverLineLoopBackThe transceiver support status of sideline loop-back control
support,notsupport.
this object belongs to xfp.ro Enumeration .18.1.2.1.1.1.27 |
rosMgmtOpticalTransceiverXFILoopBackThe transceiver support status of XFI loop-back control
support,notsupport.
this object belongs to xfp.ro Enumeration .18.1.2.1.1.1.28 |
rosMgmtOpticalTransceiverVpsThis object specifies if the optical module supports on VPS
support,notsupport.
this object belongs to xfp.ro Enumeration .18.1.2.1.1.1.29 |
rosMgmtOpticalTransceiverTxDisThe transceiver support status of software control the transmitter status
support,notsupport.
this object belongs to xfp.ro Enumeration .18.1.2.1.1.1.30 |
rosMgmtOpticalTransceiverStandbyThe transceiver support status of software control the standby mode.
support,notsupport.
this object belongs to xfp.ro Enumeration .18.1.2.1.1.1.31 |
rosMgmtOpticalTransceiverInVpsLowPowerThe VPS in low power support status of the transceiver
support,notsupport.
this object belongs to xfp.ro Enumeration .18.1.2.1.1.1.32 |
rosMgmtOpticalTransceiverOutVpsLowPowerThe VPS out low power support status of the transceiver
support,notsupport.
this object belongs to xfp.ro Enumeration .18.1.2.1.1.1.33 |
rosMgmtOpticalTransceiverFECThe FEC support status of transceiver
support,notsupport.
this object belongs to xfp.ro Enumeration .18.1.2.1.1.1.34 |
rosMgmtOpticalTransceiverCMUThe CMU support status of transceiver
support,notsupport.
this object belongs to xfp.ro Enumeration .18.1.2.1.1.1.35 |
rosMgmtOpticalTransceiverBRThis object specifies the Nominal bitrate of the transceiver,
125Mbps, 155Mbps, 622Mbps, 1.25Gbps, 2.5Gbps, 10Gbps, 100Gbps, 25Gbps.
this object belongs to xfp and sfp and qsfp and qsfp28.ro Enumeration .18.1.2.1.1.1.36 |
rosMgmtOpticalTransceiverDDMGroup OBJECT IDENTIFIER .18.1.2.2 |
rosMgmtOpticalTransceiverDDMTableThis table provides objects to monitor optical
parameters in a network element. SEQUENCE OF RosMgmtOpticalTransceiverDDMEntry .18.1.2.2.1 |
rosMgmtOpticalTransceiverDDMEntryAn entry in the rosMgmtOpticalTransceiverMonTable provides objects to
monitor an optical parameter at an optical interface. RosMgmtOpticalTransceiverDDMEntry .18.1.2.2.1.1 |
rosMgmtOpticalTransceiverParameterTypeThis object specifies the optical parameter that is being
monitored in this entry.
This object belongs to xfp/sfp. OpticalParameterType .18.1.2.2.1.1.1 |
rosMgmtOpticalTransceiverParameterValueThis object gives the value measured for the particular
optical parameter specified by the rosMgmtOpticalMonParameterType
object.
This object belongs to xfp/sfp.ro OpticalParameterValue .18.1.2.2.1.1.2 |
rosMgmtOpticalTransceiverParamHighAlarmThreshThis object gives the high alarm threshold on the
optical parameter being monitored.
An alarm condition will be raised if the value given by
rosMgmtOpticalParameterValue goes from below the value of
this object to above the value of this object, or if
the initial value of rosMgmtOpticalParameterValue exceeds the value
of this object. This alarm will be indicated in the
rosMgmtOpticalParamAlarmStatus object.
This object belongs to xfp/sfp.ro OpticalParameterValue .18.1.2.2.1.1.3 |
rosMgmtOpticalTransceiverParamHighWarningThreshThis object is used to set a high warning threshold on
the optical parameter being monitored.
A threshold crossing condition will be indicated if the value
given by rosMgmtOpticalParameterValue goes from below the value
of this object to above the value of this
object, or if the initial value of rosMgmtOpticalParameterValue
exceeds the value of this object. This alarm will be indicated in the
rosMgmtOpticalParamAlarmStatus object.
This object belongs to xfp/sfp.ro OpticalParameterValue .18.1.2.2.1.1.4 |
rosMgmtOpticalTransceiverParamLowAlarmThreshThis object is used to set a low alarm threshold on the
optical parameter being monitored.
An alarm condition will be raised if the value given by
rosMgmtOpticalParameterValue goes from above the value of
this object to below the value of this object, or if
the initial value of rosMgmtOpticalParameterValue is lower than the
value of this object. This alarm
will be indicated in the rosMgmtOpticalParamAlarmStatus object ..
This object belongs to xfp/sfp.ro OpticalParameterValue .18.1.2.2.1.1.5 |
rosMgmtOpticalTransceiverParamLowWarningThreshThis object is used to set a low warning threshold on
the optical parameter being monitored.
A threshold crossing condition will be indicated if the value
given by rosMgmtOpticalParameterValue goes from above the value
of this object to below the value of this
object, or if the initial value of rosMgmtOpticalParameterValue
object is lower than the value of this object. For
network elements in the status
indications, this threshold violation will be indicated in the
rosMgmtOpticalParamAlarmStatus object .
This object belongs to xfp/sfp.ro OpticalParameterValue .18.1.2.2.1.1.6 |
rosMgmtOpticalTransceiverParamAlarmStatusThis object is used to indicate the current status of
the thresholds for the monitored optical parameter
on the interface.
If a threshold is currently being exceeded on the
interface, the object will be set. Otherwise,
the object will be set to 1.
This object belongs to xfp/sfp.ro Enumeration .18.1.2.2.1.1.7 |
rosMgmtOpticalTransceiverParamAlarmLastValueThis object indicates the optical parameter value at the last time
a threshold related to a particular optical parameter was
exceeded on the interface.
If no threshold value is currently being
exceeded, then the value '-1000000' is returned.
This object belongs to xfp/sfp.ro OpticalParameterValue .18.1.2.2.1.1.8 |
rosMgmtOpticalTransceiverParamAlarmLastChangeThis object specifies the value of sysUpTime at the last time
a threshold related to a particular optical parameter was
exceeded on the interface.
This object belongs to xfp/sfp.ro TimeTicks (SNMPv2-SMI) .18.1.2.2.1.1.9 |
rosMgmtOpticalTransceiverDDM15MinValidIntervalsThis object gives the number of previous 15 minute
intervals for which valid performance monitoring data
has been stored on the interface.
The value of this object will be n (where n is the maximum
number of 15 minute intervals supported at this interface),
unless the measurement was (re-)started within the last
(nx15) minutes, in which case the value will be the
number of previous 15 minute intervals for which the agent
has some data.
This object belongs to xfp/sfp.ro Unsigned32 .18.1.2.2.1.1.10 |
rosMgmtOpticalTransceiverDDM24HrValidIntervalsThis object gives the number of previous 24 hour intervals
for which valid performance monitoring data has been stored
on the interface. The max value of this object is 7, it
means that the user can look up 7days history information.
This object belongs to xfp/sfp.ro Unsigned32 .18.1.2.2.1.1.11 |
rosMgmtOpticalTransceiverDDMValidStatusThis object indicates the parameter row is valid or invalid.
The object value is 'valide' when the module is present and
supporting digitaldiagnotic. The object value is 'invalid'
when the module is absent, or when the module is present and
not supporting digitaldiagnotic.
This object belongs to xfp/sfp.ro Enumeration .18.1.2.2.1.1.12 |
rosMgmtOpticalTransceiverQsfpParameterValueThis object gives the value measured for the particular
optical parameter specified by the rosMgmtOpticalMonParameterType
object.
This object belongs to Qsfp.ro OCTET STRING .18.1.2.2.1.1.13 |
rosMgmtOpticalTransceiverQsfpParamHighAlarmThreshThis object gives the high alarm threshold on the
optical parameter being monitored.
An alarm condition will be raised if the value given by
rosMgmtOpticalParameterValue goes from below the value of
this object to above the value of this object, or if
the initial value of rosMgmtOpticalParameterValue exceeds the value
of this object. This alarm will be indicated in the
rosMgmtOpticalParamAlarmStatus object.
This object belongs to Qsfp.ro OCTET STRING .18.1.2.2.1.1.14 |
rosMgmtOpticalTransceiverQsfpParamHighWarningThreshThis object is used to set a high warning threshold on
the optical parameter being monitored.
A threshold crossing condition will be indicated if the value
given by rosMgmtOpticalParameterValue goes from below the value
of this object to above the value of this
object, or if the initial value of rosMgmtOpticalParameterValue
exceeds the value of this object. This alarm will be indicated in the
rosMgmtOpticalParamAlarmStatus object.
This object belongs to Qsfp.ro OCTET STRING .18.1.2.2.1.1.15 |
rosMgmtOpticalTransceiverQsfpParamLowAlarmThreshThis object is used to set a low alarm threshold on the
optical parameter being monitored.
An alarm condition will be raised if the value given by
rosMgmtOpticalParameterValue goes from above the value of
this object to below the value of this object, or if
the initial value of rosMgmtOpticalParameterValue is lower than the
value of this object. This alarm
will be indicated in the rosMgmtOpticalParamAlarmStatus object ..
This object belongs to Qsfp.ro OCTET STRING .18.1.2.2.1.1.16 |
rosMgmtOpticalTransceiverQsfpParamLowWarningThreshThis object is used to set a low warning threshold on
the optical parameter being monitored.
A threshold crossing condition will be indicated if the value
given by rosMgmtOpticalParameterValue goes from above the value
of this object to below the value of this
object, or if the initial value of rosMgmtOpticalParameterValue
object is lower than the value of this object. For
network elements in the status
indications, this threshold violation will be indicated in the
rosMgmtOpticalParamAlarmStatus object .
This object belongs to Qsfp.ro OCTET STRING .18.1.2.2.1.1.17 |
rosMgmtOpticalTransceiverQsfpParamAlarmStatusThis object is used to indicate the current status of
the thresholds for the monitored optical parameter
on the interface.
If a threshold is currently being exceeded on the
interface, the object will be set. Otherwise,
the object will be set to 1.
This object belongs to Qsfp.ro OCTET STRING .18.1.2.2.1.1.18 |
rosMgmtOpticalTransceiverQsfpParamAlarmLastValueThis object indicates the optical parameter value at the last time
a threshold related to a particular optical parameter was
exceeded on the interface.
If no threshold value is currently being
exceeded, then the value '-1000000' is returned.
This object belongs to Qsfp.ro OCTET STRING .18.1.2.2.1.1.19 |
rosMgmtOpticalTransceiverQsfpParamAlarmLastChangeThis object specifies the value of sysUpTime at the last time
a threshold related to a particular optical parameter was
exceeded on the interface.
This object belongs to Qsfp.ro OCTET STRING .18.1.2.2.1.1.20 |
rosMgmtOpticalTransceiverQsfpDDM15MinValidIntervalsThis object gives the number of previous 15 minute
intervals for which valid performance monitoring data
has been stored on the interface.
The value of this object will be n (where n is the maximum
number of 15 minute intervals supported at this interface),
unless the measurement was (re-)started within the last
(nx15) minutes, in which case the value will be the
number of previous 15 minute intervals for which the agent
has some data.
This object belongs to Qsfp.ro OCTET STRING .18.1.2.2.1.1.21 |
rosMgmtOpticalTransceiverQsfpDDM24HrValidIntervalsThis object gives the number of previous 24 hour intervals
for which valid performance monitoring data has been stored
on the interface. The max value of this object is 7, it
means that the user can look up 7days history information.
This object belongs to Qsfp.ro OCTET STRING .18.1.2.2.1.1.22 |
rosMgmtOpticalTransceiverQsfpDDMValidStatusThis object indicates the parameter row is valid or invalid.
The object value is 'valide' when the module is present and
supporting digitaldiagnotic. The object value is 'invalid'
when the module is absent, or when the module is present and
not supporting digitaldiagnotic.
This object belongs to Qsfp.ro OCTET STRING .18.1.2.2.1.1.23 |
rosMgmtOpticalTransceiverPMGroup OBJECT IDENTIFIER .18.1.2.3 |
rosMgmtOpticalTransceiverPMCurrentTableThis table contains performance monitoring data for the
various optical parameters, collected over the current 15
minute or the current 24 hour interval. SEQUENCE OF RosMgmtOpticalTransceiverPMCurrentEntry .18.1.2.3.1 |
rosMgmtOpticalTransceiverPMCurrentEntryAn entry in the rosMgmtOpticalTransceiverPMCurrentTable. It contains
performance monitoring data for a monitored optical
parameter at an interface, collected over the current 15
minute or the current 24 hour interval. RosMgmtOpticalTransceiverPMCurrentEntry .18.1.2.3.1.1 |
rosMgmtOpticalTransceiverPMCurrentPeriodThis object indicates whether the optical parameter values
given in this entry are collected over the current 15 minute or
the current 24 hour interval.
This object belongs to xfp/sfp. OpticalPMPeriod .18.1.2.3.1.1.1 |
rosMgmtOpticalTransceiverPMCurrentParamTypeThis object specifies the optical parameter that is being
monitored, in this entry.
This object belongs to xfp/sfp. OpticalParameterType .18.1.2.3.1.1.2 |
rosMgmtOpticalTransceiverPMCurrentMaxParamThis object gives the maximum value measured for the monitored
optical parameter, in the current 15 minute or the current
24 hour interval.
This object belongs to xfp/sfp.ro OpticalParameterValue .18.1.2.3.1.1.3 |
rosMgmtOpticalTransceiverPMCurrentMinParamThis object gives the minimum value measured for the monitored
optical parameter, in the current 15 minute or the current
24 hour interval.
This object belongs to xfp/sfp.ro OpticalParameterValue .18.1.2.3.1.1.4 |
rosMgmtOpticalTransceiverPMCurrentMeanParamThis object gives the average value of the monitored
optical parameter, in the current 15 minute or the current
24 hour interval.
This object belongs to xfp/sfp.ro OpticalParameterValue .18.1.2.3.1.1.5 |
rosMgmtOpticalTransceiverQsfpPMCurrentMaxParamThis object gives the maximum value measured for the monitored
optical parameter, in the current 15 minute or the current
24 hour interval.
This object belongs to Qsfpro OCTET STRING .18.1.2.3.1.1.6 |
rosMgmtOpticalTransceiverQsfpPMCurrentMinParamThis object gives the minimum value measured for the monitored
optical parameter, in the current 15 minute or the current
24 hour interval.
This object belongs to Qsfp.ro OCTET STRING .18.1.2.3.1.1.7 |
rosMgmtOpticalTransceiverQsfpPMCurrentMeanParamThis object gives the average value of the monitored
optical parameter, in the current 15 minute or the current
24 hour interval.
This object belongs to Qsfp.ro OCTET STRING .18.1.2.3.1.1.8 |
rosMgmtOpticalTransceiverPMIntervalTableThis table stores performance monitoring data for the
various optical parameters, collected over previous
intervals.
This table can have entries for one complete 24 hour
interval and up to 96 complete 15 minute
intervals. A system is required to store at least
4 completed 15 minute intervals. The number of valid
15 minute intervals in this table is indicated by the
rosMgmtOpticalTransceiverDDM15MinValidIntervals object
and the number of valid 24 hour intervals is indicated by the
rosMgmtOpticalTransceiverDDM24HrValidIntervals object.
when the optical module is removed from the device, the relative
history records will be cleaned. SEQUENCE OF RosMgmtOpticalTransceiverPMIntervalEntry .18.1.2.3.2 |
rosMgmtOpticalTransceiverPMIntervalEntryAn entry in the rosMgmtOpticalTransceiverPMIntervalTable. It contains
performance monitoring data for an optical parameter,
collected over a previous interval. RosMgmtOpticalTransceiverPMIntervalEntry .18.1.2.3.2.1 |
rosMgmtOpticalTransceiverPMIntervalPeriodThis object indicates whether the optical parameter values,
given in this entry, are collected over a period of 15 minutes
or 24 hours.
This object belongs to xfp/sfp. OpticalPMPeriod .18.1.2.3.2.1.1 |
rosMgmtOpticalTransceiverPMIntervalNumberA number between 1 and 96, which identifies the
interval for which the set of optical parameter values is
available. The interval identified by 1 is the most recently
completed 15 minute or 24 hour interval, and the interval
identified by N is the interval immediately preceding the one
identified by N-1.
This object belongs to xfp/sfp. Integer32 .18.1.2.3.2.1.2 |
rosMgmtOpticalTransceiverPMIntervalParamTypeThis object specifies the optical parameter that is being
monitored, in this entry.
This object belongs to xfp/sfp. OpticalParameterType .18.1.2.3.2.1.3 |
rosMgmtOpticalTransceiverPMIntervalMaxParamThis object gives the maximum value measured for the optical
parameter, in a particular 15 minute or 24 hour interval.
This object belongs to xfp/sfp.ro OpticalParameterValue .18.1.2.3.2.1.4 |
rosMgmtOpticalTransceiverPMIntervalMinParamThis object gives the minimum value measured for the optical
parameter, in a particular 15 minute or 24 hour interval.
This object belongs to xfp/sfp.ro OpticalParameterValue .18.1.2.3.2.1.5 |
rosMgmtOpticalTransceiverPMIntervalMeanParamThis object gives the average value of the measured optical
parameter, in a particular 15 minute or 24 hour interval.
This object belongs to xfp/sfp.ro OpticalParameterValue .18.1.2.3.2.1.6 |
rosMgmtOpticalTransceiverQsfpPMIntervalMaxParamThis object gives the maximum value measured for the optical
parameter, in a particular 15 minute or 24 hour interval.
This object belongs to Qsfp.ro OCTET STRING .18.1.2.3.2.1.7 |
rosMgmtOpticalTransceiverQsfpPMIntervalMinParamThis object gives the minimum value measured for the optical
parameter, in a particular 15 minute or 24 hour interval.
This object belongs to Qsfp.ro OCTET STRING .18.1.2.3.2.1.8 |
rosMgmtOpticalTransceiverQsfpPMIntervalMeanParamThis object gives the average value of the measured optical
parameter, in a particular 15 minute or 24 hour interval.
This object belongs to Qsfp.ro OCTET STRING .18.1.2.3.2.1.9 |
rosMgmtOpticalTransceiverStatusGroup OBJECT IDENTIFIER .18.1.2.4 |
rosMgmtOpticalTransceiverCurrentStatusTableThis table stores the hard ware information and the information
set by user of the transceiver.
This object belongs to xfp/sfp. SEQUENCE OF RosMgmtOpticalTransceiverCurrentStatusEntry .18.1.2.4.1 |
rosMgmtOpticalTransceiverCurrentStatusEntryAn entry in the rosMgmtOpticalTransceiverCurrentStatusTable. It contains
performance monitoring data for an optical parameter,
collected over a previous interval.
This object belongs to xfp/sfp. RosMgmtOpticalTransceiverCurrentStatusEntry .18.1.2.4.1.1 |
rosMgmtOpticalTransceiverHwInfoAbsStatusThis object specifies if the optical module is absent
present,absent.
This object belongs to xfp and sfp.ro Enumeration .18.1.2.4.1.1.1 |
rosMgmtOpticalTransceiverHwInfoNRStatusThis object specifies if the optical module is ready for operation.
ready,notready.
This object belongs to xfp.ro Enumeration .18.1.2.4.1.1.2 |
rosMgmtOpticalTransceiverHwInfoRxLosStatusThis object specifies if the optical module operation losses the receiving signal
normal,loss.
This object belongs to xfp.ro Enumeration .18.1.2.4.1.1.3 |
rosMgmtOpticalTransceiverHwInfoStandbyThis object specifies if the optical module works under standby mode.
normal,standby.
This object belongs to xfp.rw Enumeration .18.1.2.4.1.1.4 |
rosMgmtOpticalTransceiverHwInfoLaserThis object specifies if the optical module laser is turned on
on,off.
This object belongs to xfp.rw Enumeration .18.1.2.4.1.1.5 |
rosMgmtOpticalTransceiverWaveLengthErrorThis object specifies error between the actual wavelength
and the wavelength set by the user,measured in pm.
This object belongs to xfp.
The object will be shown in unit of nm, and the precision is 0.001.ro Integer32 .18.1.2.4.1.1.6 |
rosMgmtOpticalTransceiverUserWaveLengthThis object specifies the wavelength value of the optical module set by user,measured in pm.
This object belongs to xfp.
The object will be shown in unit of nm, and the precision is 0.01.rw Integer32 .18.1.2.4.1.1.7 |
rosMgmtOpticalTransceiverUserDataRateThis object specifies the data rate of the optical module set by user,measured in Mbps.
This object belongs to xfp.
The object will be shown in unit of Gbps, and the precision is 0.1.rw Integer32 .18.1.2.4.1.1.8 |
rosMgmtOpticalTransceiverUserLineLoopBackThis object specifies if the sideline loop-back is tuned on ,
user can change the loop back mode through the object.
normal,lineLoopback.
This object belongs to xfp.rw Enumeration .18.1.2.4.1.1.9 |
rosMgmtOpticalTransceiverUserXFILoopBackThis object specifies if the XFI loop-back is tuned on
user can change the loop back mode through the object.
normal,xfiLoopback.
This object belongs to xfp.rw Enumeration .18.1.2.4.1.1.10 |
rosMgmtOpticalTransceiverPortNotifyEnableThis object specifies the generation of a port notifications,
enable or disable.
This object belongs to xfp and sfp.rw EnableVar .18.1.2.4.1.1.11 |
rosMgmtOpticalTransceiverPortDDMEnableThis object specifies the status of digitaldiagnotic on a port,
enable or disable.
This object belongs to xfp and sfp.rw EnableVar .18.1.2.4.1.1.12 |
rosMgmtOpticalTransceiverPortCheckPwdEnableThis object specifies the status of password checking on a port,
enable or disable.
This object belongs to xfp.rw EnableVar .18.1.2.4.1.1.13 |
rosMgmtOpticalTransceiverTxFaultCountThis object specifies the number of tx-fault signals.ro Integer32 .18.1.2.4.1.1.14 |
rosMgmtOpticalTransceiverTxFaultCountClearThis object specifies clear the statistcs of tx-fault signals.rw TruthValue (SNMPv2-TC) .18.1.2.4.1.1.15 |
rosMgmtOpticalTransceiverSpecificationCheckStatusThis object specifies the check status, accord(0)specifies
the optical module accord with industrial. not-accord(2)
specifies the optical module not accord with industrial.ro Enumeration .18.1.2.4.1.1.16 |
rosMgmtOpticalTransceiverTxFaultStatusThis object specifies the tx-fault status.ro Enumeration .18.1.2.4.1.1.17 |
rosMgmtOpticalTransceiverPortCRCCheckEnableThis object specifies the status of CRC checking on a port, enable or disable.
This object belongs to sfp and xfprw EnableVar .18.1.2.4.1.1.18 |
rosMgmtOpticalTransceiverBaseCRCCheckStatusThis object specifies the result of base information crc checking.ro Enumeration .18.1.2.4.1.1.19 |
rosMgmtOpticalTransceiverStaticDdmCRCCheckStatusThis object specifies the result of static ddm crc checking.ro Enumeration .18.1.2.4.1.1.20 |
rosMgmtOpticalTransceiverDynamicDdmCRCCheckStatusThis object specifies the result of Dynamic ddm crc checking.ro Enumeration .18.1.2.4.1.1.21 |
rosMgmtOpticalTransceiverConformance OBJECT IDENTIFIER .18.2 |