RFC1381-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for RFC1381-MIB.
60
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
60 total| Object Name |
|---|
lapb OBJECT IDENTIFIER .1.3.6.1.2.1.10.16 |
RFC1213-MIB Unknown .1.3.6.1.2.1.10.16 |
lapbAdmnTableThis table contains objects that can be
changed to manage a LAPB interface.
Changing one of these parameters may take
effect in the operating LAPB immediately or
may wait until the interface is restarted
depending on the details of the
implementation.
Most of the objects in this read-write table
have corresponding read-only objects in the
lapbOperTable that return the current
operating value.
The operating values may be different from
these configured values if changed by XID
negotiation or if a configured parameter was
changed after the interface was started. SEQUENCE OF LapbAdmnEntry .1.3.6.1.2.1.10.16.1 |
lapbAdmnEntryConfigured parameter values for a specific
LAPB. LapbAdmnEntry .1.3.6.1.2.1.10.16.1.1 |
lapbAdmnIndexThe ifIndex value for the LAPB interface.ro IfIndexType .1.3.6.1.2.1.10.16.1.1.1 |
lapbAdmnStationTypeIdentifies the desired station type of this
interface.rw Enumeration .1.3.6.1.2.1.10.16.1.1.2 |
lapbAdmnControlFieldThe desired size of the sequence numbers
used to number frames.rw Enumeration .1.3.6.1.2.1.10.16.1.1.3 |
lapbAdmnTransmitN1FrameSizeThe default maximum N1 frame size desired
in number of bits for a frame transmitted by
this DTE. This excludes flags and 0 bits
inserted for transparency.rw PositiveInteger .1.3.6.1.2.1.10.16.1.1.4 |
lapbAdmnReceiveN1FrameSizeThe default maximum N1 frame size desired
in number of bits for a frame the DCE/remote
DTE transmits to this DTE. This excludes
flags and 0 bits inserted for transparency.rw PositiveInteger .1.3.6.1.2.1.10.16.1.1.5 |
lapbAdmnTransmitKWindowSizeThe default transmit window size for this
Interface. This is the maximum number of
unacknowledged sequenced PDUs that may be
outstanding from this DTE at any one time.rw INTEGER .1.3.6.1.2.1.10.16.1.1.6 |
lapbAdmnReceiveKWindowSizeThe default receive window size for this
Interface. This is the maximum number of
unacknowledged sequenced PDUs that may be
outstanding from the DCE/remote DTE at any
one time.rw INTEGER .1.3.6.1.2.1.10.16.1.1.7 |
lapbAdmnN2RxmitCountThe default N2 retry counter for this
interface. This specifies the number of
times a PDU will be resent after the T1
timer expires without an acknowledgement for
the PDU.rw INTEGER .1.3.6.1.2.1.10.16.1.1.8 |
lapbAdmnT1AckTimerThe default T1 timer for this interface.
This specifies the maximum time in
Milliseconds to wait for acknowledgment of a
PDU.rw PositiveInteger .1.3.6.1.2.1.10.16.1.1.9 |
lapbAdmnT2AckDelayTimerThe default T2 timer for this interface.
This specifies the maximum time in
Milliseconds to wait before sending an
acknowledgment for a sequenced PDU. A value
of zero means there will be no delay in
acknowledgement generation.rw PositiveInteger .1.3.6.1.2.1.10.16.1.1.10 |
lapbAdmnT3DisconnectTimerThe T3 timer for this interface. This
specifies the time in Milliseconds to wait
before considering the link disconnected. A
value of zero indicates the link will be
considered disconnected upon completion of
the frame exchange to disconnect the link.rw PositiveInteger .1.3.6.1.2.1.10.16.1.1.11 |
lapbAdmnT4IdleTimerThe T4 timer for this interface. This
specifies the maximum time in Milliseconds
to allow without frames being exchanged on
the data link. A value of 2147483647
indicates no idle timer is being kept.rw PositiveInteger .1.3.6.1.2.1.10.16.1.1.12 |
lapbAdmnActionInitiateThis identifies the action LAPB will take
to initiate link set-up.rw Enumeration .1.3.6.1.2.1.10.16.1.1.13 |
lapbAdmnActionRecvDMThis identifies the action LAPB will take
when it receives a DM response.rw Enumeration .1.3.6.1.2.1.10.16.1.1.14 |
lapbOperTableThis table contains configuration
information about interface parameters
currently set in the interface. Many of
these objects have corresponding objects in
the lapbAdmnTable. SEQUENCE OF LapbOperEntry .1.3.6.1.2.1.10.16.2 |
lapbOperEntryCurrently set parameter values for a
specific LAPB. LapbOperEntry .1.3.6.1.2.1.10.16.2.1 |
lapbOperIndexThe ifIndex value for the LAPB interface.ro IfIndexType .1.3.6.1.2.1.10.16.2.1.1 |
lapbOperStationTypeIdentifies the current operating station
type of this interface. A value of dxe (3)
indicates XID negotiation has not yet taken
place.ro Enumeration .1.3.6.1.2.1.10.16.2.1.2 |
lapbOperControlFieldThe current operating size of the sequence
numbers used to number frames.ro Enumeration .1.3.6.1.2.1.10.16.2.1.3 |
lapbOperTransmitN1FrameSizeThe current operating N1 frame size used
for the maximum number of bits in a frame
this DTE can transmit. This excludes flags
and 0 bits inserted for transparency.ro PositiveInteger .1.3.6.1.2.1.10.16.2.1.4 |
lapbOperReceiveN1FrameSizeThe current operating N1 frame size used
for the maximum number of bits in a frame
the DCE/remote DTE can transmit. This
excludes flags and 0 bits inserted for
transparency.ro PositiveInteger .1.3.6.1.2.1.10.16.2.1.5 |
lapbOperTransmitKWindowSizeThe current PDU window size this Interface
uses to transmit. This is the maximum
number of unacknowledged sequenced PDUs that
may be outstanding from this DTE at any one
time.ro INTEGER .1.3.6.1.2.1.10.16.2.1.6 |
lapbOperReceiveKWindowSizeThe current receive PDU window size for
this Interface. This is the maximum number
of unacknowledged sequenced PDUs that may be
outstanding from the DCE/remote DTE at any
one time.ro INTEGER .1.3.6.1.2.1.10.16.2.1.7 |
lapbOperN2RxmitCountThe current N2 retry counter used for this
interface. This specifies the number of
times a PDU will be resent after the T1
timer expires without an acknowledgement for
the PDU.ro INTEGER .1.3.6.1.2.1.10.16.2.1.8 |
lapbOperT1AckTimerThe current T1 timer for this interface.
This specifies the maximum time in
Milliseconds to wait for acknowledgment of a
PDU.ro PositiveInteger .1.3.6.1.2.1.10.16.2.1.9 |
lapbOperT2AckDelayTimerThe current T2 timer for this interface.
This specifies the maximum time in
Milliseconds to wait before sending an
acknowledgment for a sequenced PDU. A value
of zero means there will be no delay in
acknowledgement generation.ro PositiveInteger .1.3.6.1.2.1.10.16.2.1.10 |
lapbOperT3DisconnectTimerThe current T3 timer for this interface.
This specifies the time in Milliseconds to
wait before considering the link
disconnected. A value of zero indicates the
link will be considered disconnected upon
completion of the frame exchange to
disconnect the link.ro PositiveInteger .1.3.6.1.2.1.10.16.2.1.11 |
lapbOperT4IdleTimerThe current T4 timer for this interface.
This specifies the maximum time in
Milliseconds to allow without frames being
exchanged on the data link. A value of
2147483647 indicates no idle timer is being
kept.rw PositiveInteger .1.3.6.1.2.1.10.16.2.1.12 |
lapbOperPortIdThis object identifies an instance of the
index object in the first group of objects
in the MIB specific to the physical device
or interface used to send and receive
frames. If an agent does not support any
such objects, it should return nullSpec
OBJECT IDENTIFIER {0 0}.ro OBJECT IDENTIFIER .1.3.6.1.2.1.10.16.2.1.13 |
lapbOperProtocolVersionIdThis object identifies the version of the
lapb protocol implemented by this
interface.ro OBJECT IDENTIFIER .1.3.6.1.2.1.10.16.2.1.14 |
lapbFlowTableThis table defines the objects recorded by
LAPB to provide information about the
traffic flow through the interface. SEQUENCE OF LapbFlowEntry .1.3.6.1.2.1.10.16.3 |
lapbFlowEntryThe information regarding the effects of
flow controls in LAPB. LapbFlowEntry .1.3.6.1.2.1.10.16.3.1 |
lapbFlowIfIndexThe ifIndex value for the LAPB Interface.ro IfIndexType .1.3.6.1.2.1.10.16.3.1.1 |
lapbFlowStateChangesThe number of LAPB State Changes, including
resets.ro Counter .1.3.6.1.2.1.10.16.3.1.2 |
lapbFlowChangeReasonThe reason for the most recent incrementing
of lapbFlowStateChanges. A DM or DISC frame
generated to initiate link set-up does not
alter this object. When the MIB-II object
ifOperStatus does not have a value of
testing, there exists a correlation between
this object and ifOperStatus. IfOperStatus
will have a value of up when this object
contains: abmEntered, abmeEntered,
abmReset, or abmeReset. IfOperStatus will
have a value of down when this object has a
value of notStarted, or dmReceived through
n2Timeout. There is no correlation when
this object has the value other.ro Enumeration .1.3.6.1.2.1.10.16.3.1.3 |
lapbFlowCurrentModeThe current condition of the conversation.ro Enumeration .1.3.6.1.2.1.10.16.3.1.4 |
lapbFlowBusyDefersThe number of times this device was unable
to transmit a frame due to a perceived
remote busy condition. Busy conditions can
result from the receipt of an RNR from the
remote device, the lack of valid sequence
number space (window saturation), or other
conditions.ro Counter .1.3.6.1.2.1.10.16.3.1.5 |
lapbFlowRejOutPktsThe number of REJ or SREJ frames sent by
this station.ro Counter .1.3.6.1.2.1.10.16.3.1.6 |
lapbFlowRejInPktsThe number of REJ or SREJ frames received
by this station.ro Counter .1.3.6.1.2.1.10.16.3.1.7 |
lapbFlowT1TimeoutsThe number of times a re-transmission was
effected by the T1 Timer expiring.ro Counter .1.3.6.1.2.1.10.16.3.1.8 |
lapbFlowFrmrSentThe Information Field of the FRMR most
recently sent. If no FRMR has been sent
(the normal case) or the information isn't
available, this will be an OCTET STRING of
zero length.ro OCTET STRING .1.3.6.1.2.1.10.16.3.1.9 |
lapbFlowFrmrReceivedThe Information Field of the FRMR most
recently received. If no FRMR has been
received (the normal case) or the
information isn't available, this will be an
OCTET STRING of zero length.ro OCTET STRING .1.3.6.1.2.1.10.16.3.1.10 |
lapbFlowXidReceivedThe Information Field of the XID frame most
recently received. If no XID frame has been
received, this will be an OCTET STRING of
zero length.ro OCTET STRING .1.3.6.1.2.1.10.16.3.1.11 |
lapbXidTableThis table defines values to use for XID
negotiation that are not found in the
lapbAdmnTable. This table is optional for
implementations that don't support XID and
mandatory for implementations that do
initiate XID negotiation. SEQUENCE OF LapbXidEntry .1.3.6.1.2.1.10.16.4 |
lapbXidEntryXId negotiation parameter values for a
specific LAPB. LapbXidEntry .1.3.6.1.2.1.10.16.4.1 |
lapbXidIndexThe ifIndex value for the LAPB interface.ro IfIndexType .1.3.6.1.2.1.10.16.4.1.1 |
lapbXidAdRIdentifierThe value of the Address Resolution
Identifier. A zero length string indicates
no Identifier value has been assigned.rw OCTET STRING .1.3.6.1.2.1.10.16.4.1.2 |
lapbXidAdRAddressThe value of the Address Resolution
Address. A zero length string indicates no
Address value has been assigned.rw OCTET STRING .1.3.6.1.2.1.10.16.4.1.3 |
lapbXidParameterUniqueIdentifierThe value of the parameter unique
Identifier. A zero length string indicates
no Unique identifier value has been
assigned.rw OCTET STRING .1.3.6.1.2.1.10.16.4.1.4 |
lapbXidGroupAddressThe value of the parameter Group address.
A zero length string indicates no Group
address value has been assigned.rw OCTET STRING .1.3.6.1.2.1.10.16.4.1.5 |
lapbXidPortNumberThe port number assigned for this link. A
zero length string indicates no local port
number identifier has been assigned.rw OCTET STRING .1.3.6.1.2.1.10.16.4.1.6 |
lapbXidUserDataSubfieldA user data subfield, if any, to be
transmitted in an XID frame. A zero length
frame indicates no user data subfield has
been assigned. The octet string should
include both the User data identifier and
User data field as shown in Figures 1 and
4.rw OCTET STRING .1.3.6.1.2.1.10.16.4.1.7 |
lapbProtocolVersion OBJECT IDENTIFIER .1.3.6.1.2.1.10.16.5 |
lapbProtocolIso7776v1986 OBJECT IDENTIFIER .1.3.6.1.2.1.10.16.5.1 |
lapbProtocolCcittV1980 OBJECT IDENTIFIER .1.3.6.1.2.1.10.16.5.2 |
lapbProtocolCcittV1984 OBJECT IDENTIFIER .1.3.6.1.2.1.10.16.5.3 |