RFC1286-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
83
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
83 total| Object Name |
|---|
dot1dBridge OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.17 |
RFC1213-MIB Unknown .1.3.6.1.4.1.727.7.2.1.17 |
newRootThe newRoot trap indicates that the sending agent
has become the new root of the Spanning Tree; the
trap is sent by a bridge soon after its election
as the new root, e.g., upon expiration of the
Topology Change Timer immediately subsequent to
its election. TRAP-TYPE .1.3.6.1.4.1.727.7.2.1.17.0.1 |
topologyChangeA topologyChange trap is sent by a bridge when
any of its configured ports transitions from the
Learning state to the Forwarding state, or from
the Forwarding state to the Blocking state. The
trap is not sent if a newRoot trap is sent for the
same transition. TRAP-TYPE .1.3.6.1.4.1.727.7.2.1.17.0.2 |
dot1dBase OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.17.1 |
dot1dBaseBridgeAddressThe MAC address used by this bridge when it must
be referred to in a unique fashion. It is
recommended that this be the numerically smallest
MAC address of all ports that belong to this
bridge. However it is only required to be unique.
When concatenated with dot1dStpPriority a unique
BridgeIdentifier is formed which is used in the
Spanning Tree Protocol.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.727.7.2.1.17.1.1 |
dot1dBaseNumPortsThe number of ports controlled by this bridging
entity.ro INTEGER .1.3.6.1.4.1.727.7.2.1.17.1.2 |
dot1dBaseTypeIndicates what type of bridging this bridge can
perform. If a bridge is actually performing a
certain type of bridging this will be indicated by
entries in the port table for the given type.ro Enumeration .1.3.6.1.4.1.727.7.2.1.17.1.3 |
dot1dBasePortTableA table that contains generic information about
every port that is associated with this bridge.
Transparent, source-route, and srt ports are
included. SEQUENCE OF Dot1dBasePortEntry .1.3.6.1.4.1.727.7.2.1.17.1.4 |
dot1dBasePortEntryA list of information for each port of the
bridge. Dot1dBasePortEntry .1.3.6.1.4.1.727.7.2.1.17.1.4.1 |
dot1dBasePortThe port number of the port for which this entry
contains bridge management information.ro INTEGER .1.3.6.1.4.1.727.7.2.1.17.1.4.1.1 |
dot1dBasePortIfIndexThe value of the instance of the ifIndex object,
defined in [4,6], for the interface corresponding
to this port.ro INTEGER .1.3.6.1.4.1.727.7.2.1.17.1.4.1.2 |
dot1dBasePortCircuitFor a port which (potentially) has the same value
of dot1dBasePortIfIndex as another port on the
same bridge, this object contains the name of an
object instance unique to this port. For example,
in the case where multiple ports correspond one-
to-one with multiple X.25 virtual circuits, this
value might identify an (e.g., the first) object
instance associated with the X.25 virtual circuit
corresponding to this port.
For a port which has a unique value of
dot1dBasePortIfIndex, this object can have the
value { 0 0 }.ro OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.17.1.4.1.3 |
dot1dBasePortDelayExceededDiscardsThe number of frames discarded by this port due
to excessive transit delay through the bridge. It
is incremented by both transparent and source
route bridges.ro Counter .1.3.6.1.4.1.727.7.2.1.17.1.4.1.4 |
dot1dBasePortMtuExceededDiscardsThe number of frames discarded by this port due
to an excessive size. It is incremented by both
transparent and source route bridges.ro Counter .1.3.6.1.4.1.727.7.2.1.17.1.4.1.5 |
dot1dStp OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.17.2 |
dot1dStpProtocolSpecificationAn indication of what version of the Spanning
Tree Protocol is being run. The value
'decLb100(2)' indicates the DEC LANbridge 100
Spanning Tree protocol. IEEE 802.1d
implementations will return 'ieee8021d(3)'. If
future versions of the IEEE Spanning Tree Protocol
are released that are incompatible with the
current version a new value will be defined.ro Enumeration .1.3.6.1.4.1.727.7.2.1.17.2.1 |
dot1dStpPriorityThe value of the write-able portion of the Bridge
ID, i.e., the first two octets of the (8 octet
long) Bridge ID. The other (last) 6 octets of the
Bridge ID are given by the value of
dot1dBaseBridgeAddress.rw INTEGER .1.3.6.1.4.1.727.7.2.1.17.2.2 |
dot1dStpTimeSinceTopologyChangeThe time (in hundredths of a second) since the
last time a topology change was detected by the
bridge entity.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.727.7.2.1.17.2.3 |
dot1dStpTopChangesThe total number of topology changes detected by
this bridge since the management entity was last
reset or initialized.ro Counter .1.3.6.1.4.1.727.7.2.1.17.2.4 |
dot1dStpDesignatedRootThe bridge identifier of the root of the spanning
tree as determined by the Spanning Tree Protocol
as executed by this node. This value is used as
the Root Identifier parameter in all Configuration
Bridge PDUs originated by this node.ro BridgeId .1.3.6.1.4.1.727.7.2.1.17.2.5 |
dot1dStpRootCostThe cost of the path to the root as seen from
this bridge.ro INTEGER .1.3.6.1.4.1.727.7.2.1.17.2.6 |
dot1dStpRootPortThe port number of the port which offers the
lowest cost path from this bridge to the root
bridge.ro INTEGER .1.3.6.1.4.1.727.7.2.1.17.2.7 |
dot1dStpMaxAgeThe maximum age of Spanning Tree Protocol
information learned from the network on any port
before it is discarded, in units of hundredths of
a second. This is the actual value that this
bridge is currently using.ro Timeout .1.3.6.1.4.1.727.7.2.1.17.2.8 |
dot1dStpHelloTimeThe amount of time between the transmission of
Configuration bridge PDUs by this node on any port
when it is the root of the spanning tree or trying
to become so, in units of hundredths of a second.
This is the actual value that this bridge is
currently using.ro Timeout .1.3.6.1.4.1.727.7.2.1.17.2.9 |
dot1dStpHoldTimeThis time value determines the interval length
during which no more than two Configuration bridge
PDUs shall be transmitted by this node, in units
of hundredths of a second.ro INTEGER .1.3.6.1.4.1.727.7.2.1.17.2.10 |
dot1dStpForwardDelayThis time value, measured in units of hundredths
of a second, controls how fast a port changes its
spanning state when moving towards the Forwarding
state. The value determines how long the port
stays in a particular state before moving to the
next state. For example, how long a port stays in
the Listening state when moving from Blocking to
Learning. This value is also used, when a
topology change has been detected and is underway,
to age all dynamic entries in the Forwarding
Database. [Note that this value is the one that
this bridge is currently using, in contrast to
dot1dStpBridgeForwardDelay which is the value that
this bridge and all others would start using
if/when this bridge were to become the root.]ro Timeout .1.3.6.1.4.1.727.7.2.1.17.2.11 |
dot1dStpBridgeMaxAgeThe value that all bridges use for MaxAge when
this bridge is acting as the root. Note that
802.1d/D9 specifies that the range for this
parameter is related to the value of
dot1dStpBridgeHelloTime. The granularity of this
timer is specified by 802.1d/D9 to be 1 second.
An agent may return a badValue error if a set is
attempted to a value which is not a whole number
of seconds.rw Timeout .1.3.6.1.4.1.727.7.2.1.17.2.12 |
dot1dStpBridgeHelloTimeThe value that all bridges use for HelloTime when
this bridge is acting as the root. The
granularity of this timer is specified by
802.1d/D9 to be 1 second. An agent may return a
badValue error if a set is attempted to a value
which is not a whole number of seconds.rw Timeout .1.3.6.1.4.1.727.7.2.1.17.2.13 |
dot1dStpBridgeForwardDelayThe value that all bridges use for ForwardDelay
when this bridge is acting as the root. Note that
802.1d/D9 specifies that the range for this
parameter is related to the value of
dot1dStpBridgeMaxAge. The granularity of this
timer is specified by 802.1d/D9 to be 1 second.
An agent may return a badValue error if a set is
attempted to a value which is not a whole number
of seconds.rw Timeout .1.3.6.1.4.1.727.7.2.1.17.2.14 |
dot1dStpPortTableA table that contains port-specific information
for the Spanning Tree Protocol. SEQUENCE OF Dot1dStpPortEntry .1.3.6.1.4.1.727.7.2.1.17.2.15 |
dot1dStpPortEntryA list of information maintained by every port
about the Spanning Tree Protocol state for that
port. Dot1dStpPortEntry .1.3.6.1.4.1.727.7.2.1.17.2.15.1 |
dot1dStpPortThe port number of the port for which this entry
contains Spanning Tree Protocol management
information.ro INTEGER .1.3.6.1.4.1.727.7.2.1.17.2.15.1.1 |
dot1dStpPortPriorityThe value of the priority field which is
contained in the first (in network byte order)
octet of the (2 octet long) Port ID. The other
octet of the Port ID is given by the value of
dot1dStpPort.rw INTEGER .1.3.6.1.4.1.727.7.2.1.17.2.15.1.2 |
dot1dStpPortStateThe port's current state as defined by
application of the Spanning Tree Protocol. This
state controls what action a port takes on
reception of a frame. If the bridge has detected
a port that is malfunctioning it will place that
port into the broken(6) state. For ports which
are disabled (see dot1dStpPortEnable), this object
will have a value of disabled(1).ro Enumeration .1.3.6.1.4.1.727.7.2.1.17.2.15.1.3 |
dot1dStpPortEnableThe enabled/disabled status of the port.rw Enumeration .1.3.6.1.4.1.727.7.2.1.17.2.15.1.4 |
dot1dStpPortPathCostThe contribution of this port to the path cost of
paths towards the spanning tree root which include
this port.rw INTEGER .1.3.6.1.4.1.727.7.2.1.17.2.15.1.5 |
dot1dStpPortDesignatedRootThe unique Bridge Identifier of the Bridge
recorded as the Root in the Configuration BPDUs
transmitted by the Designated Bridge for the
segment to which the port is attached.ro BridgeId .1.3.6.1.4.1.727.7.2.1.17.2.15.1.6 |
dot1dStpPortDesignatedCostThe path cost of the Designated Port of the
segment connected to this port. This value is
compared to the Root Path Cost field in received
bridge PDUs.ro INTEGER .1.3.6.1.4.1.727.7.2.1.17.2.15.1.7 |
dot1dStpPortDesignatedBridgeThe Bridge Identifier of the bridge which this
port considers to be the Designated Bridge for
this port's segment.ro BridgeId .1.3.6.1.4.1.727.7.2.1.17.2.15.1.8 |
dot1dStpPortDesignatedPortThe Port Identifier of the port on the Designated
Bridge for this port's segment.ro OCTET STRING .1.3.6.1.4.1.727.7.2.1.17.2.15.1.9 |
dot1dStpPortForwardTransitionsThe number of times this port has transitioned
from the Learning state to the Forwarding state.ro Counter .1.3.6.1.4.1.727.7.2.1.17.2.15.1.10 |
dot1dSr OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.17.3 |
dot1dSrPortTableA table that contains information about every
port that is associated with this source route
bridge. SEQUENCE OF Dot1dSrPortEntry .1.3.6.1.4.1.727.7.2.1.17.3.1 |
dot1dSrPortEntryA list of information for each port of a source
route bridge. Dot1dSrPortEntry .1.3.6.1.4.1.727.7.2.1.17.3.1.1 |
dot1dSrPortThe port number of the port for which this entry
contains Source Route management information.ro INTEGER .1.3.6.1.4.1.727.7.2.1.17.3.1.1.1 |
dot1dSrPortHopCountThe maximum number of routing descriptors allowed
in an All Paths or Spanning Tree Explorer frames.rw INTEGER .1.3.6.1.4.1.727.7.2.1.17.3.1.1.2 |
dot1dSrPortLocalSegmentThe segment number that uniquely identifies the
segment to which this port is connected. Current
source routing protocols limit this value to the
range: 0 through 4095. A value of 65535 signifies
that no segment number is assigned to this port.rw INTEGER .1.3.6.1.4.1.727.7.2.1.17.3.1.1.3 |
dot1dSrPortBridgeNumA bridge number uniquely identifies a bridge when
more than one bridge is used to span the same two
segments. Current source routing protocols limit
this value to the range: 0 through 15. A value of
65535 signifies that no bridge number is assigned
to this bridge.rw INTEGER .1.3.6.1.4.1.727.7.2.1.17.3.1.1.4 |
dot1dSrPortTargetSegmentThe segment number that corresponds to the target
segment this port is considered to be connected to
by the bridge. Current source routing protocols
limit this value to the range: 0 through 4095. A
value of 65535 signifies that no target segment is
assigned to this port.rw INTEGER .1.3.6.1.4.1.727.7.2.1.17.3.1.1.5 |
dot1dSrPortLargestFrameThe maximum size of the INFO field (LLC and
above) that this port can send/receive. It does
not include any MAC level (framing) octets. The
value of this object is used by this bridge to
determine whether a modification of the
LargestFrame (LF, see [14]) field of the Routing
Control field of the Routing Information Field is
necessary. Valid values as defined by the 802.5
source routing bridging specification[14] are 516,
1500, 2052, 4472, 8144, 11407, 17800, and 65535
octets. Behavior of the port when an illegal
value is written is implementation specific. It
is recommended that a reasonable legal value be
chosen.rw Enumeration .1.3.6.1.4.1.727.7.2.1.17.3.1.1.6 |
dot1dSrPortSTESpanModeDetermines how this port behaves when presented
with a Spanning Tree Explorer frame. The value
'disabled(2)' indicates that the port will not
accept or send Spanning Tree Explorer packets; any
STE packets received will be silently discarded.
The value 'forced(3)' indicates the port will
always accept and propagate Spanning Tree Explorer
frames. This allows a manually configured
Spanning Tree for this class of packet to be
configured. Note that unlike transparent bridging
this is not catastrophic to the network if there
are loops. The value 'auto-span(1)' can only be
returned by a bridge that both implements the
Spanning Tree Protocol and has use of the protocol
enabled on this port. The behavior of the port for
Spanning Tree Explorer frames is determined by the
state of dot1dStpPortState. If the port is in the
'forwarding' state, the frame will be accepted or
propagated. Otherwise it will be silently
discarded.rw Enumeration .1.3.6.1.4.1.727.7.2.1.17.3.1.1.7 |
dot1dSrPortSpecInFramesThe number of specifically routed frames that
have been received from this port's segment.ro Counter .1.3.6.1.4.1.727.7.2.1.17.3.1.1.8 |
dot1dSrPortSpecOutFramesThe number of specifically routed frames that
this port has transmitted on its segment.ro Counter .1.3.6.1.4.1.727.7.2.1.17.3.1.1.9 |
dot1dSrPortApeInFramesThe number of all paths explorer frames that have
been received by this port from its segment.ro Counter .1.3.6.1.4.1.727.7.2.1.17.3.1.1.10 |
dot1dSrPortApeOutFramesThe number of all paths explorer frames that have
been transmitted by this port on its segment.ro Counter .1.3.6.1.4.1.727.7.2.1.17.3.1.1.11 |
dot1dSrPortSteInFramesThe number of spanning tree explorer frames that
have been received by this port from its segment.ro Counter .1.3.6.1.4.1.727.7.2.1.17.3.1.1.12 |
dot1dSrPortSteOutFramesThe number of spanning tree explorer frames that
have been transmitted by this port on its
segment.ro Counter .1.3.6.1.4.1.727.7.2.1.17.3.1.1.13 |
dot1dSrPortSegmentMismatchDiscardsThe number of explorer frames that have been
discarded by this port because the routing
descriptor field contained an invalid adjacent
segment value.ro Counter .1.3.6.1.4.1.727.7.2.1.17.3.1.1.14 |
dot1dSrPortDuplicateSegmentDiscardsThe number of frames that have been discarded by
this port because the routing descriptor field
contained a duplicate segment identifier.ro Counter .1.3.6.1.4.1.727.7.2.1.17.3.1.1.15 |
dot1dSrPortHopCountExceededDiscardsThe number of explorer frames that have been
discarded by this port because the Routing
Information Field has exceeded the maximum route
descriptor length.ro Counter .1.3.6.1.4.1.727.7.2.1.17.3.1.1.16 |
dot1dTp OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.17.4 |
dot1dTpLearnedEntryDiscardsThe total number of Forwarding Database entries,
which have been or would have been learnt, but
have been discarded due to a lack of space to
store them in the Forwarding Database. If this
counter is increasing, it indicates that the
Forwarding Database is regularly becoming full (a
condition which has unpleasant performance effects
on the subnetwork). If this counter has a
significant value but is not presently increasing,
it indicates that the problem has been occurring
but is not persistent.ro Counter .1.3.6.1.4.1.727.7.2.1.17.4.1 |
dot1dTpAgingTimeThe timeout period in seconds for aging out
dynamically learned forwarding information.rw INTEGER .1.3.6.1.4.1.727.7.2.1.17.4.2 |
dot1dTpFdbTableA table that contains information about unicast
entries for which the bridge has forwarding and/or
filtering information. This information is used
by the transparent bridging function in
determining how to propagate a received frame. SEQUENCE OF Dot1dTpFdbEntry .1.3.6.1.4.1.727.7.2.1.17.4.3 |
dot1dTpFdbEntryInformation about a specific unicast MAC address
for which the bridge has some forwarding and/or
filtering information. Dot1dTpFdbEntry .1.3.6.1.4.1.727.7.2.1.17.4.3.1 |
dot1dTpFdbAddressA unicast MAC address for which the bridge has
forwarding and/or filtering information.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.727.7.2.1.17.4.3.1.1 |
dot1dTpFdbPortEither the value '0', or the port number of the
port on which a frame having a source address
equal to the value of the corresponding instance
of dot1dTpFdbAddress has been seen. A value of
'0' indicates that the port number has not been
learned but that the bridge does have some
forwarding/filtering information about this
address (e.g. in the dot1dStaticTable).
Implementors are encouraged to assign the port
value to this object whenever it is learned even
for addresses for which the corresponding value of
dot1dTpFdbStatus is not learned(3).ro INTEGER .1.3.6.1.4.1.727.7.2.1.17.4.3.1.2 |
dot1dTpFdbStatusThe status of this entry. The meanings of the
values are:
other(1) : none of the following. This would
include the case where some other
MIB object (not the corresponding
instance of dot1dTpFdbPort, nor an
entry in the dot1dStaticTable) is
being used to determine if and how
frames addressed to the value of
the corresponding instance of
dot1dTpFdbAddress are being
forwarded.
invalid(2) : this entry is not longer valid
(e.g., it was learned but has since
aged-out), but has not yet been
flushed from the table.
learned(3) : the value of the corresponding
instance of dot1dTpFdbPort was
learned, and is being used.
self(4) : the value of the corresponding
instance of dot1dTpFdbAddress
represents one of the bridge's
addresses. The corresponding
instance of dot1dTpFdbPort
indicates which of the bridge's
ports has this address.
mgmt(5) : the value of the corresponding
instance of dot1dTpFdbAddress is
also the value of an existing
instance of dot1dStaticAddress.ro Enumeration .1.3.6.1.4.1.727.7.2.1.17.4.3.1.3 |
dot1dTpPortTableA table that contains information about every
port that is associated with this transparent
bridge. SEQUENCE OF Dot1dTpPortEntry .1.3.6.1.4.1.727.7.2.1.17.4.4 |
dot1dTpPortEntryA list of information for each port of a
transparent bridge. Dot1dTpPortEntry .1.3.6.1.4.1.727.7.2.1.17.4.4.1 |
dot1dTpPortThe port number of the port for which this entry
contains Transparent bridging management
information.ro INTEGER .1.3.6.1.4.1.727.7.2.1.17.4.4.1.1 |
dot1dTpPortMaxInfoThe maximum size of the INFO (non-MAC) field that
this port will receive or transmit.ro INTEGER .1.3.6.1.4.1.727.7.2.1.17.4.4.1.2 |
dot1dTpPortInFramesThe number of frames that have been received by
this port from its segment. Note that a frame
received on the interface corresponding to this
port is only counted by this object if and only if
it is for a protocol being processed by the local
bridging function.ro Counter .1.3.6.1.4.1.727.7.2.1.17.4.4.1.3 |
dot1dTpPortOutFramesThe number of frames that have been transmitted
by this port to its segment. Note that a frame
transmitted on the interface corresponding to this
port is only counted by this object if and only if
it is for a protocol being processed by the local
bridging function.ro Counter .1.3.6.1.4.1.727.7.2.1.17.4.4.1.4 |
dot1dTpPortInDiscardsCount of valid frames received which were
discarded (i.e., filtered) by the Forwarding
Process.ro Counter .1.3.6.1.4.1.727.7.2.1.17.4.4.1.5 |
dot1dStatic OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.17.5 |
dot1dStaticTableA table containing filtering information
configured into the bridge by (local or network)
management specifying the set of ports to which
frames received from specific ports and containing
specific destination addresses are allowed to be
forwarded. The value of zero in this table as the
port number from which frames with a specific
destination address are received, is used to
specify all ports for which there is no specific
entry in this table for that particular
destination address. Entries are valid for
unicast and for group/broadcast addresses. SEQUENCE OF Dot1dStaticEntry .1.3.6.1.4.1.727.7.2.1.17.5.1 |
dot1dStaticEntryFiltering information configured into the bridge
by (local or network) management specifying the
set of ports to which frames received from a
specific port and containing a specific
destination address are allowed to be forwarded. Dot1dStaticEntry .1.3.6.1.4.1.727.7.2.1.17.5.1.1 |
dot1dStaticAddressThe destination MAC address in a frame to which
this entry's filtering information applies. This
object can take the value of a unicast address, a
group address or the broadcast address.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.727.7.2.1.17.5.1.1.1 |
dot1dStaticReceivePortEither the value '0', or the port number of the
port from which a frame must be received in order
for this entry's filtering information to apply.
A value of zero indicates that this entry applies
on all ports of the bridge for which there is no
other applicable entry.rw INTEGER .1.3.6.1.4.1.727.7.2.1.17.5.1.1.2 |
dot1dStaticAllowedToGoToThe set of ports to which frames received from a
specific port and destined for a specific MAC
address, are allowed to be forwarded. Each octet
within the value of this object specifies a set of
eight ports, with the first octet specifying ports
1 through 8, the second octet specifying ports 9
through 16, etc. Within each octet, the most
significant bit represents the lowest numbered
port, and the least significant bit represents the
highest numbered port. Thus, each port of the
bridge is represented by a single bit within the
value of this object. If that bit has a value of
'1' then that port is included in the set of
ports; the port is not included if its bit has a
value of '0'. (Note that the setting of the bit
corresponding to the port from which a frame is
received is irrelevant.)rw OCTET STRING .1.3.6.1.4.1.727.7.2.1.17.5.1.1.3 |
dot1dStaticStatusThis object indicates the status of this entry.
other(1) - this entry is currently in use but
the conditions under which it will
remain so are different from each of the
following values.
invalid(2) - writing this value to the object
removes the corresponding entry.
permanent(3) - this entry is currently in use
and will remain so after the next reset
of the bridge.
deleteOnReset(4) - this entry is currently in
use and will remain so until the next
reset of the bridge.
deleteOnTimeout(5) - this entry is currently
in use and will remain so until it is
aged out.rw Enumeration .1.3.6.1.4.1.727.7.2.1.17.5.1.1.4 |