RFC1231-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for RFC1231-MIB.
41
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
41 total| Object Name |
|---|
transmission OBJECT IDENTIFIER .1.3.6.1.2.1.10 |
RFC1213-MIB Unknown .1.3.6.1.2.1.10 |
dot5 OBJECT IDENTIFIER .1.3.6.1.2.1.10.9 |
dot5TableThis table contains Token Ring interface
parameters and state variables, one entry
per 802.5 interface. SEQUENCE OF Dot5Entry .1.3.6.1.2.1.10.9.1 |
dot5EntryA list of Token Ring status and parameter
values for an 802.5 interface. Dot5Entry .1.3.6.1.2.1.10.9.1.1 |
dot5IfIndexThe value of this object identifies the
802.5 interface for which this entry
contains management information. The
value of this object for a particular
interface has the same value as the
ifIndex object, defined in [4,6],
for the same interface.ro INTEGER .1.3.6.1.2.1.10.9.1.1.1 |
dot5CommandsWhen this object is set to the value of
open(2), the station should go into the
open state. The progress and success of
the open is given by the values of the
objects dot5RingState and
dot5RingOpenStatus.
When this object is set to the value
of reset(3), then the station should do
a reset. On a reset, all MIB counters
should retain their values, if possible.
Other side affects are dependent on the
hardware chip set.
When this object is set to the value
of close(4), the station should go into
the stopped state by removing itself
from the ring.
Setting this object to a value of
no-op(1) has no effect.
When read, this object always has a
value of no-op(1).rw Enumeration .1.3.6.1.2.1.10.9.1.1.2 |
dot5RingStatusThe current interface status which can
be used to diagnose fluctuating problems
that can occur on token rings, after a
station has successfully been added to
the ring.
Before an open is completed, this
object has the value for the 'no status'
condition. The dot5RingState and
dot5RingOpenStatus objects provide for
debugging problems when the station
can not even enter the ring.
The object's value is a sum of
values, one for each currently applicable
condition. The following values are
defined for various conditions:
0 = No Problems detected
32 = Ring Recovery
64 = Single Station
256 = Remove Received
512 = reserved
1024 = Auto-Removal Error
2048 = Lobe Wire Fault
4096 = Transmit Beacon
8192 = Soft Error
16384 = Hard Error
32768 = Signal Loss
131072 = no status, open not completed.ro INTEGER .1.3.6.1.2.1.10.9.1.1.3 |
dot5RingStateThe current interface state with respect
to entering or leaving the ring.ro Enumeration .1.3.6.1.2.1.10.9.1.1.4 |
dot5RingOpenStatusThis object indicates the success, or the
reason for failure, of the station's most
recent attempt to enter the ring.ro Enumeration .1.3.6.1.2.1.10.9.1.1.5 |
dot5RingSpeedThe ring's bandwidth.rw Enumeration .1.3.6.1.2.1.10.9.1.1.6 |
dot5UpStreamThe MAC-address of the up stream neighbor
station in the ring.ro MacAddress (SNMPv2-TC) .1.3.6.1.2.1.10.9.1.1.7 |
dot5ActMonParticipateIf this object has a value of true(1) then
this interface will participate in the
active monitor selection process. If the
value is false(2) then it will not.
Setting this object might not have an
effect until the next time the interface
is opened.rw Enumeration .1.3.6.1.2.1.10.9.1.1.8 |
dot5FunctionalThe bit mask of all Token Ring functional
addresses for which this interface will
accept frames.rw MacAddress (SNMPv2-TC) .1.3.6.1.2.1.10.9.1.1.9 |
dot5StatsTableA table containing Token Ring statistics,
one entry per 802.5 interface.
All the statistics are defined using
the syntax Counter as 32-bit wrap around
counters. Thus, if an interface's
hardware maintains these statistics in
16-bit counters, then the agent must read
the hardware's counters frequently enough
to prevent loss of significance, in order
to maintain 32-bit counters in software. SEQUENCE OF Dot5StatsEntry .1.3.6.1.2.1.10.9.2 |
dot5StatsEntryAn entry contains the 802.5 statistics
for a particular interface. Dot5StatsEntry .1.3.6.1.2.1.10.9.2.1 |
dot5StatsIfIndexThe value of this object identifies the
802.5 interface for which this entry
contains management information. The
value of this object for a particular
interface has the same value as the
ifIndex object, defined in [4,6], for
the same interface.ro INTEGER .1.3.6.1.2.1.10.9.2.1.1 |
dot5StatsLineErrorsThis counter is incremented when a frame
or token is copied or repeated by a
station, the E bit is zero in the frame
or token and one of the following
conditions exists: 1) there is a
non-data bit (J or K bit) between the SD
and the ED of the frame or token, or
2) there is an FCS error in the frame.ro Counter .1.3.6.1.2.1.10.9.2.1.2 |
dot5StatsBurstErrorsThis counter is incremented when a station
detects the absence of transitions for five
half-bit timers (burst-five error).ro Counter .1.3.6.1.2.1.10.9.2.1.3 |
dot5StatsACErrorsThis counter is incremented when a station
receives an AMP or SMP frame in which A is
equal to C is equal to 0, and then receives
another SMP frame with A is equal to C is
equal to 0 without first receiving an AMP
frame. It denotes a station that cannot set
the AC bits properly.ro Counter .1.3.6.1.2.1.10.9.2.1.4 |
dot5StatsAbortTransErrorsThis counter is incremented when a station
transmits an abort delimiter while
transmitting.ro Counter .1.3.6.1.2.1.10.9.2.1.5 |
dot5StatsInternalErrorsThis counter is incremented when a station
recognizes an internal error.ro Counter .1.3.6.1.2.1.10.9.2.1.6 |
dot5StatsLostFrameErrorsThis counter is incremented when a station
is transmitting and its TRR timer expires.
This condition denotes a condition where a
transmitting station in strip mode does not
receive the trailer of the frame before the
TRR timer goes off.ro Counter .1.3.6.1.2.1.10.9.2.1.7 |
dot5StatsReceiveCongestionsThis counter is incremented when a station
recognizes a frame addressed to its
specific address, but has no available
buffer space indicating that the station
is congested.ro Counter .1.3.6.1.2.1.10.9.2.1.8 |
dot5StatsFrameCopiedErrorsThis counter is incremented when a station
recognizes a frame addressed to its
specific address and detects that the FS
field A bits are set to 1 indicating a
possible line hit or duplicate address.ro Counter .1.3.6.1.2.1.10.9.2.1.9 |
dot5StatsTokenErrorsThis counter is incremented when a station
acting as the active monitor recognizes an
error condition that needs a token
transmitted.ro Counter .1.3.6.1.2.1.10.9.2.1.10 |
dot5StatsSoftErrorsThe number of Soft Errors the interface
has detected. It directly corresponds to
the number of Report Error MAC frames
that this interface has transmitted.
Soft Errors are those which are
recoverable by the MAC layer protocols.ro Counter .1.3.6.1.2.1.10.9.2.1.11 |
dot5StatsHardErrorsThe number of times this interface has
detected an immediately recoverable
fatal error. It denotes the number of
times this interface is either
transmitting or receiving beacon MAC
frames.ro Counter .1.3.6.1.2.1.10.9.2.1.12 |
dot5StatsSignalLossThe number of times this interface has
detected the loss of signal condition from
the ring.ro Counter .1.3.6.1.2.1.10.9.2.1.13 |
dot5StatsTransmitBeaconsThe number of times this interface has
transmitted a beacon frame.ro Counter .1.3.6.1.2.1.10.9.2.1.14 |
dot5StatsRecoverysThe number of Claim Token MAC frames
received or transmitted after the interface
has received a Ring Purge MAC frame. This
counter signifies the number of times the
ring has been purged and is being recovered
back into a normal operating state.ro Counter .1.3.6.1.2.1.10.9.2.1.15 |
dot5StatsLobeWiresThe number of times the interface has
detected an open or short circuit in the
lobe data path. The adapter will be closed
and dot5RingState will signify this
condition.ro Counter .1.3.6.1.2.1.10.9.2.1.16 |
dot5StatsRemovesThe number of times the interface has
received a Remove Ring Station MAC frame
request. When this frame is received
the interface will enter the close state
and dot5RingState will signify this
condition.ro Counter .1.3.6.1.2.1.10.9.2.1.17 |
dot5StatsSinglesThe number of times the interface has
sensed that it is the only station on the
ring. This will happen if the interface
is the first one up on a ring, or if
there is a hardware problem.ro Counter .1.3.6.1.2.1.10.9.2.1.18 |
dot5StatsFreqErrorsThe number of times the interface has
detected that the frequency of the
incoming signal differs from the expected
frequency by more than that specified by
the IEEE 802.5 standard, see chapter 7
in [10].ro Counter .1.3.6.1.2.1.10.9.2.1.19 |
dot5Tests OBJECT IDENTIFIER .1.3.6.1.2.1.10.9.3 |
testInsertFunc OBJECT IDENTIFIER .1.3.6.1.2.1.10.9.3.1 |
dot5ChipSets OBJECT IDENTIFIER .1.3.6.1.2.1.10.9.4 |
chipSetIBM16 OBJECT IDENTIFIER .1.3.6.1.2.1.10.9.4.1 |
chipSetTItms380 OBJECT IDENTIFIER .1.3.6.1.2.1.10.9.4.2 |
chipSetTItms380c16 OBJECT IDENTIFIER .1.3.6.1.2.1.10.9.4.3 |