PROXIM-MIB
AI MIB Summary
The PROXIM-MIB module enables SNMP-based monitoring and management of Proxim Wireless enterprise access points and bridges, specifically tracking RF link statistics, association states, channel utilization, and signal quality metrics for the 802.11b/g/n wireless infrastructure.
MIB Definition used in the Proxim Wireless Product Line: iso(1).org(3).dod(6).internet(1).private(4).enterprises(1). proxim(841)
Main OID:
proxim.1.3.6.1.4.1.841
990
Objects
Active
Status
2
Dependencies
Imported Objects
Objects
990 total| Object Name |
|---|
proximMIB Definition used in the Proxim Wireless Product Line: iso(1).org(3).dod(6).internet(1).private(4).enterprises(1). proxim(841) MODULE-IDENTITY .1.3.6.1.4.1.841 |
wireless OBJECT IDENTIFIER .1.3.6.1.4.1.841.1 |
objects OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1 |
deviceConfig OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.1 |
interface OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.1.1 |
wirelessIf OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.1.1.1 |
wirelessIfPropertiesTableThis table contains information on the properties and capabilities of the wireless interface(s) present in the device. SEQUENCE OF WirelessIfPropertiesTableEntry .1.3.6.1.4.1.841.1.1.1.1.1.1 |
wirelessIfPropertiesTableEntryThis parameter represents the entry in the wireless interface properties table. WirelessIfPropertiesTableEntry .1.3.6.1.4.1.841.1.1.1.1.1.1.1 |
wirelessIfPropertiesTableIndexThis parameter represents a unique value for each Wireless interface in the system and is used as index to this table.ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.1.1.1 |
wirelessIfPropertiesRadioStatusThis parameter is used to provide the status of the Wireless Radio interface. Select (1) to enable the wireless interface and (2) to disable the wireless interface.rw Enumeration .1.3.6.1.4.1.841.1.1.1.1.1.1.1.2 |
wirelessIfOperationalModeThis parameter is used to set the wireless NIC Operational mode. Depending on the wireless NIC in the device different wireless operational modes can be configured. The object wirelessIfSupportedOperationalMode shows the supported modes and the possible supported modes for AP products: dot11b(1), dot11g(2), dot11ng(3), dot11a(4), dot11na(5)rw DisplayString .1.3.6.1.4.1.841.1.1.1.1.1.1.1.3 |
wirelessIfSupportedOperationalModeThis parameter is used to set the wireless supported Operational mode.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.1.1.1.1.4 |
wirelessIfCurrentChannelBandwidthThis parameter represents the current bandwidth that Wireless is currently operating on. It is represented in MHzrw Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.1.1.5 |
wirelessIfSupportedChannelBandwidthThis parameter represents the channel bandwidths that a wireless can support.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.1.1.1.1.6 |
wirelessIfAutoChannelSelectionThis parameter is used to configure the auto channel selection for wireless interface. Select (1) to enable the auto channel selection and (2) to disable the auto channel selection.rw Enumeration .1.3.6.1.4.1.841.1.1.1.1.1.1.1.7 |
wirelessIfCurrentOperatingChannelThis parameter represents the user configured channel that the radio is configured to operate in. Note: It is possible that the currently active channel is different. To find the current active/operational channel refer to wirelessIfCurrentActiveChannel.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.1.1.8 |
wirelessIfSupportedChannelsThis parameter represents the channels that wireless can support.ro OCTET STRING .1.3.6.1.4.1.841.1.1.1.1.1.1.1.9 |
wirelessIfAutoRateSelectionThis parameter is used to configure the value for Auto Rate Selection for the wireless interface. Select (1) to enable the Auto Rate selection and (2) to disable the Auto Rate selection.rw Enumeration .1.3.6.1.4.1.841.1.1.1.1.1.1.1.10 |
wirelessIfTransmittedRateThis parameter represents the number of rates transmitted for wireless.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.1.1.11 |
wirelessIfSupportedRateThis parameter represents the number of rates supported for wireless.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.1.1.1.1.12 |
wirelessIfVAPRTSThresholdThis parameter represents the maximum threshold for VAP RTS (Request To Send). The maximum threshold can be configured up to 2346.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.1.1.13 |
wirelessIfVAPBeaconIntervalThis parameter represents the time interval that a beacon takes for getting transmitted for wireless VAP. By default, the value is set to 100 ms.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.1.1.14 |
wirelessIfTPCThis parameter represents the cell size that the transmitted power controls. It is measured in dBm. Please check the wirelessIfActiveTPC for current active TPC.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.1.1.15 |
wirelessIfCellSizeThis parameter represents the cell size of the wireless. By default, the cell size is configured to large. Select (1) for Small cell size, (2) for Medium cell size and (3) for Large cell size.rw Enumeration .1.3.6.1.4.1.841.1.1.1.1.1.1.1.16 |
wirelessIfDTIMThis parameter represents the delivery traffic indication map period. This is the interval between the transmission of multicast frames on the wireless inteface. It is expressed in the Beacon messages. The recommended default value for this parameter is 1.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.1.1.17 |
wirelessIfAntennaGainThis parameter is used to configure the antenna gain.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.1.1.18 |
wirelessIfCurrentActiveChannelThis parameter represents the current active channel that wireless radio is operating on. It may be different from the configured channel represented by wirelessIfCurrentOperatingChannel.ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.1.1.19 |
wirelessIfSatelliteDensityThis parameter represents the density of the satellites for the BSU. It configures the BSU to accomodate the satellites for the specified range.rw Enumeration .1.3.6.1.4.1.841.1.1.1.1.1.1.1.20 |
wirelessIfMPOperationalModeThis parameter is used to set the wireless NIC Operational mode for Tsunami Multi Point Products.rw Enumeration .1.3.6.1.4.1.841.1.1.1.1.1.1.1.21 |
wirelessIfChannelWaitTimeThis parameter is used to configure the DFS channel wait time.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.1.1.22 |
wirelessIfActiveTPCThis parameter shows the active cell size that the transmitted power controls. It is measured in dBmro Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.1.1.23 |
wirelessIfDfsNumSatWithRadarForFreqSwitchThis parameter represents the minimum number of satellites reporting RADAR for BSU to switch to a new best channel/frequency. The default value is (0) that indicates BSU to never switch to a new best channel/frequency for any number of satellites reporting RADAR.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.1.1.24 |
wirelessIfDfsStatusThis parameter is used to configure the status of the DFS for SU. Configuring this parameter for BSU will not affecte BSU Status. 1 to enable the DFS, 2 to disable the DFS.rw Enumeration .1.3.6.1.4.1.841.1.1.1.1.1.1.1.25 |
wirelessIf11nPropertiesTableThis table holds the wireless11n configurations. SEQUENCE OF WirelessIf11nPropertiesTableEntry .1.3.6.1.4.1.841.1.1.1.1.1.2 |
wirelessIf11nPropertiesTableEntryThis parameter represents the entry for wireless11n properties table. WirelessIf11nPropertiesTableEntry .1.3.6.1.4.1.841.1.1.1.1.1.2.1 |
wirelessIf11nPropertiesTableIndexThis parameter represents index to the wireless interface 11n table and this represents the wireless radios.ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.2.1.1 |
wirelessIf11nPropertiesAMPDUStatusThis parameter is used define the AMPDU status for wireless 11n interface. Select 1 to enable and 2 to disable the AMPDU status.rw Enumeration .1.3.6.1.4.1.841.1.1.1.1.1.2.1.2 |
wirelessIf11nPropertiesAMPDUMaxNumFramesThis parameter represents the Agregated MAC Protocol Data Unit (AMPDU) frames that are transmitted. It can be configured up to 64 frames.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.2.1.3 |
wirelessIf11nPropertiesAMPDUMaxFrameSizeThis parameter is used to configure the maximum AMPDU frame size (in bytes) that can be transmitted.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.2.1.4 |
wirelessIf11nPropertiesAMSDUStatusThis parameter is used define the AMSDU status for wireless 11n interface. Select 1 to enable and 2 to disable the AMSDU status.rw Enumeration .1.3.6.1.4.1.841.1.1.1.1.1.2.1.5 |
wirelessIf11nPropertiesAMSDUMaxFrameSizeThis parameter shows the maximum AMSDU frame size (in bytes) that can be transmitted.ro Unsigned32 (4096) .1.3.6.1.4.1.841.1.1.1.1.1.2.1.6 |
wirelessIf11nPropertiesFrequencyExtensionThis parameter is used to configure the frequency extension for the wireless interface. Select 1 to configure the UpperExtensionChannel and 2 to configure the LowerExtensionChannel.rw Enumeration .1.3.6.1.4.1.841.1.1.1.1.1.2.1.7 |
wirelessIf11nPropertiesGuardIntervalThis parameter is used to configure the guard interval for the wireless interface. Select 1 for short guard interval as 400 nano seconds and 2 for full guard interval as 800 nano seconds.rw Enumeration .1.3.6.1.4.1.841.1.1.1.1.1.2.1.8 |
wirelessIf11nPropertiesTxAntennasThis parameter enables the transmission antennas. This is configured as bit-mask. Eg: 3 - 011 (binary value) - first and second antennas are enabled. 7 - 111 (binary value) - all three are enabled.rw Enumeration .1.3.6.1.4.1.841.1.1.1.1.1.2.1.9 |
wirelessIf11nPropertiesRxAntennasThis parameter enables the receiving antennas. This is configured as bit-mask. Eg: 3 - 011 (binary value) - first and second antennas are enabled. 7 - 111 (binary value) - all three are enabled.rw Enumeration .1.3.6.1.4.1.841.1.1.1.1.1.2.1.10 |
wirelessIf11nPropertiesNumOfSpatialStreamsThis parameter is used to select the number of spatial streams for 11n.rw Enumeration .1.3.6.1.4.1.841.1.1.1.1.1.2.1.11 |
wirelessIf11nPropertiesSupportedTxAntennasThis parameter shows the number of supported Tx antennas.ro DisplayString .1.3.6.1.4.1.841.1.1.1.1.1.2.1.12 |
wirelessIf11nPropertiesSupportedRxAntennasThis parameter shows the number of supported Rx antennas.ro DisplayString .1.3.6.1.4.1.841.1.1.1.1.1.2.1.13 |
wirelessIfVAPTableThis table holds the wireless VAP (virtual access point) configurations. SEQUENCE OF WirelessIfVAPTableEntry .1.3.6.1.4.1.841.1.1.1.1.1.3 |
wirelessIfVAPTableEntryThis parameter represents the entry for the wireless VAP table. WirelessIfVAPTableEntry .1.3.6.1.4.1.841.1.1.1.1.1.3.1 |
wirelessIfVAPTableIndexThis parameter is used to configure the wireless VAP table. Select 1 represents Wifi0 (radio-0) and 2 represents Wifi1 (radio-1).ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.3.1.1 |
wirelessIfVAPTableSecIndexThis parameter represents the VAPs and used as secondary index to this table.ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.3.1.2 |
wirelessIfVAPTypeThis parameter is used to configure the type of VAP. Select 1 for AP.rw Enumeration .1.3.6.1.4.1.841.1.1.1.1.1.3.1.3 |
wirelessIfVAPSSIDThis parameter is used to represent the wireless card SSID name (wireless network name).rw DisplayString .1.3.6.1.4.1.841.1.1.1.1.1.3.1.4 |
wirelessIfVAPBSSIDThis parameter represents the MAC address for the VAP BSSID.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.1.1.3.1.5 |
wirelessIfVAPBroadcastSSIDThis parameter is used to configure the status of the broadcast wireless VAP SSID. A single entry in the SSID table can be enabled to broadcast SSID in beacon messages. Select 1 to enable, 2 to disablerw Enumeration .1.3.6.1.4.1.841.1.1.1.1.1.3.1.6 |
wirelessIfVAPFragmentationThresholdThis parameter is used to configure the fragmentation threshold for the wireless VAP. By default, the value is set to 2346.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.3.1.7 |
wirelessIfVAPSecurityProfileNameThis parameter allows you to configure the Security profile name for Wireless VAP.rw DisplayString .1.3.6.1.4.1.841.1.1.1.1.1.3.1.8 |
wirelessIfVAPRadiusProfileNameThis parameter allows you to configure the RADIUS profile name for Wireless VAP.rw DisplayString .1.3.6.1.4.1.841.1.1.1.1.1.3.1.9 |
wirelessIfVAPVLANIDThis parameter is used to represent the VLAN ID for the wireless VAP. Select any value between 1 - 4094 to tag the VLAN ids and -1 to untag the VLAN ids.rw VlanId .1.3.6.1.4.1.841.1.1.1.1.1.3.1.10 |
wirelessIfVAPVLANPriorityThis parameter is used to configure the VLAN priority for Wireless VAP. By default the value is set to 0.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.3.1.11 |
wirelessIfVAPQoSProfileNameThis parameter is used to configure the profile name for the Wireless VAP QoS.rw DisplayString .1.3.6.1.4.1.841.1.1.1.1.1.3.1.12 |
wirelessIfVAPMACACLStatusThis parameter is used to enable or disable the MAC access control list.rw Enumeration .1.3.6.1.4.1.841.1.1.1.1.1.3.1.13 |
wirelessIfVAPRadiusMACACLStatusThis parameter is used to enable or disable the MAC ACL for Radius Profilesrw Enumeration .1.3.6.1.4.1.841.1.1.1.1.1.3.1.14 |
wirelessIfVAPRadiusAccStatusThis parameter is used to enable or disable the Radius Accounting Stats capture.rw Enumeration .1.3.6.1.4.1.841.1.1.1.1.1.3.1.15 |
wirelessIfVAPStatusThis parameter is used to configure the status of the VAP. Select 1 to enable the VAP, 2 to disable the VAP and 3 to delete the VAP.rw Enumeration .1.3.6.1.4.1.841.1.1.1.1.1.3.1.16 |
wirelessIfWORPTableThis table holds the wireless WORP protocol configurations SEQUENCE OF WirelessIfWORPTableEntry .1.3.6.1.4.1.841.1.1.1.1.1.4 |
wirelessIfWORPTableEntryThis object represents the entry for the wireless WORP table WirelessIfWORPTableEntry .1.3.6.1.4.1.841.1.1.1.1.1.4.1 |
wirelessIfWORPTableIndexThis parameter represents the radio for which the WORP is enabled and index to the wirelessIfWORPTable.ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.4.1.1 |
wirelessIfWORPModeThis parameter displays the worp mode of operation.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.1.1.4.1.2 |
wirelessIfWORPBaseStationNameThis parameter represents the name of the BSU for which it can register. This configuration is valid only on SU. If this field is empty then SU is allowed to register with any BSU.rw DisplayString .1.3.6.1.4.1.841.1.1.1.1.1.4.1.3 |
wirelessIfWORPNetworkNameThis parameter represents the name of the Network of the WORP Interface.rw DisplayString .1.3.6.1.4.1.841.1.1.1.1.1.4.1.4 |
wirelessIfWORPMaxSatellitesThis parameter represents the maximum number of SUs allowed to register on this BSU. This configuration is valid only on BSU.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.4.1.5 |
wirelessIfWORPMTUThis parameter represents to maximum size of a frame sent from the WORP interface.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.4.1.6 |
wirelessIfWORPSuperPacketingThis parameter represents the status of bundling multiple ethernet frames in one single WORP Jumbo framerw Enumeration .1.3.6.1.4.1.841.1.1.1.1.1.4.1.7 |
wirelessIfWORPSleepModeThis parameter represents the status of sleep mode. This Configuration is valid only on BSU. If there is no data available to transfer b/w BSU & SU, BSU will keep the SU state in sleep state and polls that particular SU for every 4 seconds to just to maintain the WORP link.rw Enumeration .1.3.6.1.4.1.841.1.1.1.1.1.4.1.8 |
wirelessIfWORPMultiFrameBurstingThis parameter enables WORP protocol to allow each side, BSU or SU, to send a burst of multiple data messages instead of a single data message.rw Enumeration .1.3.6.1.4.1.841.1.1.1.1.1.4.1.9 |
wirelessIfWORPRegistrationTimeoutThis parameter represents the registration procedure timeout period for WORP interface.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.4.1.11 |
wirelessIfWORPRetriesThis parameter represents the number of times the same worp frame need to be re-Transmitted, if it is not acknowledged by the peer.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.4.1.12 |
wirelessIfWORPTxRateThis parameter represents the WORP interface transmission rate. Please check the object wirelessIfWORPSupportedTxRate for supported rates.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.4.1.13 |
wirelessIfWORPSupportedTxRateThis parameter displays the supported transmission rate based on Channel Bandwdith, Guard Interval and Number of Spacial Streams configuration.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.1.1.4.1.14 |
wirelessIfWORPInputBandwidthLimitThis parameters represents the Bandwidth limit on Input direction. Default limit & maximum limit are based on the license file.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.4.1.15 |
wirelessIfWORPOutputBandwidthLimitThis parameter represents the Bandwidth limit on Output direction. Default limit & maximum limit are based on the license file.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.4.1.16 |
wirelessIfWORPBandwidthLimitTypeThis parameter represents the bandwidth limit type - shaping or policing.rw Enumeration .1.3.6.1.4.1.841.1.1.1.1.1.4.1.17 |
wirelessIfWORPSecurityProfileIndexThis parameter allows to configure the Security profile for the WORP interface based on the index of the profile name and this is Valid only on BSU.rw Enumeration .1.3.6.1.4.1.841.1.1.1.1.1.4.1.18 |
wirelessIfWORPRadiusProfileIndexThis parameter allows to configure the Radius profile for the WORP interface based on the index of the profile name and this is Valid only on BSU..rw Enumeration .1.3.6.1.4.1.841.1.1.1.1.1.4.1.19 |
wirelessIfWORPMACACLStatusThis parameter is used to enable or disable the MAC access control list. This configuration is Valid only on BSU.rw Enumeration .1.3.6.1.4.1.841.1.1.1.1.1.4.1.20 |
wirelessIfWORPRadiusMACACLStatusThis parameter is used to enable or disable the MAC ACL for Radius Profiles. This configuration is Valid only on BSU.rw Enumeration .1.3.6.1.4.1.841.1.1.1.1.1.4.1.21 |
wirelessIfWORPRadiusAccStatusThis parameter is used to enable or disable the Radius Accounting Stats capture. This configuration is Valid only on BSU and currently this is not accessible. Enumeration .1.3.6.1.4.1.841.1.1.1.1.1.4.1.22 |
wirelessIfWORPIntfMacAddressThis parameter represents the MAC address of the wireless interface card.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.1.1.4.1.23 |
wirelessIfWORPAutoMultiFrameBurstingThis parameter enables WORP protocol to allow each side, BSU or SU, to send a burst of multiple data messages based on QOS priority instead of a single data message.rw Enumeration .1.3.6.1.4.1.841.1.1.1.1.1.4.1.24 |
wirelessIfDDRSTableThis table holds the WORP DDRS (Dynamic Data Rate Selection) feature configurations. SEQUENCE OF WirelessIfDDRSTableEntry .1.3.6.1.4.1.841.1.1.1.1.1.5 |
wirelessIfDDRSTableEntryThis parameter represents the entry for DDRS table. WirelessIfDDRSTableEntry .1.3.6.1.4.1.841.1.1.1.1.1.5.1 |
wirelessIfDDRSTableIndexThis parameter represents the index for the DDRS table and indirectly represent the wireless interface index.ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.5.1.1 |
wirelessIfDDRSStatusThis parameter is used to enable/disable the DDRS feature for the interface.rw Enumeration .1.3.6.1.4.1.841.1.1.1.1.1.5.1.2 |
wirelessIfDDRSDefDataRateThis default data rate shall be used as WORP default data rate only when the DDRS is enabled. The rates defined in wirelessIfWORPTxRate are used as default.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.5.1.3 |
wirelessIfDDRSMaxDataRateThis parameter is used to limit the maximum possible data rate that is set by DDRS.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.5.1.4 |
wirelessIfDDRSIncrAvgSNRThrldThis parameter is used to specify the average SNR threshold for data rate increase. The value should be in dB and in the range of 0..50 dB.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.5.1.5 |
wirelessIfDDRSIncrReqSNRThrldThis parameter is to specify minimum required SNR threshold for data rate increase. The value should be in dB and in the range 0..50 dB.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.5.1.6 |
wirelessIfDDRSDecrReqSNRThrldThis parameter is to specify minimum required SNR threshold for data rate decrease. The value should be in dB and in the range 0..50 dB.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.5.1.7 |
wirelessIfDDRSIncrReTxPercentThrldThis object specifies the threshold percentage of retransmissions for DDRS data rate increase.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.5.1.8 |
wirelessIfDDRSDecrReTxPercentThrldThis object specifies the threshold percentage of retransmissions for DDRS data rate decrease.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.5.1.9 |
wirelessIfDDRSAggressiveIndexThis object specifies the aggressiveness of the ddrs algorithm.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.5.1.10 |
wirelessIfDDRSChainBalThrldThis object specifies the Mimo Chain Balance threshold.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.5.1.11 |
wirelessIfDDRSRateBackOffIntThis object specifies the Rate Backoff Interval.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.5.1.12 |
wirelessIfDDRSRateBlackListIntThis object specifies the Rate Blacklist Interval.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.5.1.13 |
wirelessIfDDRSMinReqSNRTable SEQUENCE OF WirelessIfDDRSMinReqSNRTableEntry .1.3.6.1.4.1.841.1.1.1.1.1.6 |
wirelessIfDDRSMinReqSNRTableEntry WirelessIfDDRSMinReqSNRTableEntry .1.3.6.1.4.1.841.1.1.1.1.1.6.1 |
wirelessIfDDRSMinReqSNRTableIndexro Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.6.1.1 |
wirelessIfDDRSMinReqSNRTableSecIndexro Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.6.1.2 |
wirelessIfDDRSPhyModulationro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.1.1.6.1.3 |
wirelessIfDDRSDataRatero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.1.1.6.1.4 |
wirelessIfDDRSMinReqSNRrw Unsigned32 .1.3.6.1.4.1.841.1.1.1.1.1.6.1.5 |
ethernetIf OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.1.1.2 |
ethernetIfPropertiesTableThis table shows the ethernet interface(s) properties for the device. SEQUENCE OF EthernetIfPropertiesTableEntry .1.3.6.1.4.1.841.1.1.1.1.2.1 |
ethernetIfPropertiesTableEntryThis parameter represents the entry for the Ethernet Interface Properties table. EthernetIfPropertiesTableEntry .1.3.6.1.4.1.841.1.1.1.1.2.1.1 |
ethernetIfPropertiesTableIndexThis parameter represents the physical interface and used as index to this table.ro Unsigned32 (1) .1.3.6.1.4.1.841.1.1.1.1.2.1.1.1 |
ethernetIfMACAddressThis parameter represents the MAC address for the ethernet interface.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.1.2.1.1.2 |
ethernetIfSupportedSpeedThis parameter shows the supported speeds for the ethernet interface.ro Enumeration .1.3.6.1.4.1.841.1.1.1.1.2.1.1.3 |
ethernetIfSupportedTxModeThis parameter shows the supported transmit modes of the ethernet interface.ro Enumeration .1.3.6.1.4.1.841.1.1.1.1.2.1.1.4 |
ethernetIfTxModeAndSpeedThis parameter is used to configure the Transmit Mode and speed of the ethernet interface.rw Enumeration .1.3.6.1.4.1.841.1.1.1.1.2.1.1.5 |
ethernetIfSupportedModesThis parameter is used to display the supported modes on ethernet interface.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.1.2.1.1.6 |
ethernetIfAdminStatusThis parameter is used to configure the admin status for the ethernet interface.rw Enumeration .1.3.6.1.4.1.841.1.1.1.1.2.1.1.7 |
ethernetIfAutoShutDownThis parameter is used to configure AutoShutDown for the ethernet interface. i.e. Ethernet interface will be automatically UP/DOWN depending upon the wireless linkrw Enumeration .1.3.6.1.4.1.841.1.1.1.1.2.1.1.8 |
apSecurity OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.1.2 |
wirelessSecurity OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.1.2.1 |
wirelessSecurityCfgTableThis table is used to specify the security configuration for the wireless interface(s) in the access point. SEQUENCE OF WirelessSecurityCfgTableEntry .1.3.6.1.4.1.841.1.1.1.2.1.1 |
wirelessSecurityCfgTableEntryThis parameter represents an entry in the wireless security configuration table. This table supports up to 8 entries. WirelessSecurityCfgTableEntry .1.3.6.1.4.1.841.1.1.1.2.1.1.1 |
wirelessSecurityCfgTableIndexThis parameter is used as index to the wireless security configuration table.ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.2.1.1.1.1 |
wirelessSecurityCfgprofileNameThis paramater represents user defined profile name for security configuration.rw DisplayString .1.3.6.1.4.1.841.1.1.1.2.1.1.1.2 |
wirelessSecurityCfgAuthenticationModeThis parameter is used to configure the security authentication mode for wireless. Select (1) - None (no security), (2) - WEP (Wired Equivalent Privacy), (3) - PSK (Pre-shared key), (4) - dotlx (802.1x authentication) and (5) - worp (Wireless Outdoor Router Protocol).rw Enumeration .1.3.6.1.4.1.841.1.1.1.2.1.1.1.3 |
wirelessSecurityCfgKeyIndexThis parameter represents the encryption key index that is used to encrypt data that is sent via wireless interface(s).rw Enumeration .1.3.6.1.4.1.841.1.1.1.2.1.1.1.4 |
wirelessSecurityCfgKey1This parameter represents the key 1 used for wireless security configuration. The key lengths 5/13/16 in ASCII or 10/26/32 in HEXADECIMAL configures the WEP(64/128/152-bit) encryption respectively. The key lengths 16 in ASCII or 32 in HEXADECIMAL configures the TKIP(128-bit) or AES-CCM(128-bit) encryption.rw WEPKeyType .1.3.6.1.4.1.841.1.1.1.2.1.1.1.5 |
wirelessSecurityCfgdot1xWepKeyLengthThis parameter is used configure the length of the security key. Select WEP64 if you want to have a security key for 64 characters or WEP128 for security key length of 128 characters.rw Enumeration .1.3.6.1.4.1.841.1.1.1.2.1.1.1.6 |
wirelessSecurityCfgEncryptionTypeThis parameter is used to configure the encryption key type for wireless security. Select 0 for no security 1 for WEP, 2 for WPA (TKIP), 3 for WPA2(AES), 4 for WPA/WPA2 (AES-TKIP) 5 for WPA2 (AES-CCM). 6 for TKIP -- Used only for TMP/QB products 7 for AES-CCM -- Used only for TMP/QB products.rw Enumeration .1.3.6.1.4.1.841.1.1.1.2.1.1.1.7 |
wirelessSecurityCfgPSKThis parameter is used to configure the pre-share key. The default key is 123456789. This parameter is logically write-only. Reading this variable shall return astericksrw DisplayString .1.3.6.1.4.1.841.1.1.1.2.1.1.1.8 |
wirelessSecurityCfgRekeyingIntervalThis parameter represents the key re-negotiation time in case of dynamic WEP, WPA/WPA-2 (personal/enterprise) security mechanisms.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.2.1.1.1.9 |
wirelessSecurityCfgEntryStatusThis parameter is used to configure the entry status of wireless security configuration table. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.2.1.1.1.10 |
wirelessSecurityCfgNetworkSecretThis parameter represents a secret password of an SU that tallies with the BSU's password for authentic registration.rw DisplayString .1.3.6.1.4.1.841.1.1.1.2.1.1.1.11 |
wirelessSecurityCfgKey2This parameter represents the key 2 used for wireless security configuration. The key lengths 5/13/16 in ASCII or 10/26/32 in HEXADECIMAL configures the WEP(64/128/152-bit) encryption respectively. The key lengths 16 in ASCII or 32 in HEXADECIMAL configures the TKIP(128-bit) or AES-CCM(128-bit) encryption.rw WEPKeyType .1.3.6.1.4.1.841.1.1.1.2.1.1.1.12 |
wirelessSecurityCfgKey3This parameter represents the key 3 used for wireless security configuration. The key lengths 5/13/16 in ASCII or 10/26/32 in HEXADECIMAL configures the WEP(64/128/152-bit) encryption respectively. The key lengths 16 in ASCII or 32 in HEXADECIMAL configures the TKIP(128-bit) or AES-CCM(128-bit) encryption.rw WEPKeyType .1.3.6.1.4.1.841.1.1.1.2.1.1.1.13 |
wirelessSecurityCfgKey4This parameter represents the key 4 used for wireless security configuration. The key lengths 5/13/16 in ASCII or 10/26/32 in HEXADECIMAL configures the WEP(64/128/152-bit) encryption respectively. The key lengths 16 in ASCII or 32 in HEXADECIMAL configures the TKIP(128-bit) or AES-CCM(128-bit) encryption.rw WEPKeyType .1.3.6.1.4.1.841.1.1.1.2.1.1.1.14 |
radius OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.1.2.2 |
radiusSrvProfileTableThis table contains the radius server configuration profiles. SEQUENCE OF RadiusSrvProfileTableEntry .1.3.6.1.4.1.841.1.1.1.2.2.1 |
radiusSrvProfileTableEntryThis parameter represents the entry for the radius server profile table. RadiusSrvProfileTableEntry .1.3.6.1.4.1.841.1.1.1.2.2.1.1 |
radiusSrvProfileTableIndexThis parameter represents the user defined profiles for RADIUS Server.ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.2.2.1.1.1 |
radiusSrvProfileTableSecIndexThis parameter represents the user defined secondary profiles for RADIUS server. Maximum profiles are 4.ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.2.2.1.1.2 |
radiusSrvProfileTypeThis parameter represents the RADIUS Server profile type. Select (1) for Primary Authentication Server, (2) for Secondary Authentication Server, (3) for Primary Accounting Server, and (4) for Secondary Accounting Server.ro Enumeration .1.3.6.1.4.1.841.1.1.1.2.2.1.1.3 |
radiusSrvIPADDRThis parameter is used to specify the RADIUS Server IP Address. Its default value is 169.254.128.133.rw IpAddress .1.3.6.1.4.1.841.1.1.1.2.2.1.1.4 |
radiusSrvServerPortThis parameter represents the RADIUS server authentication port and the default value is 1812.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.2.2.1.1.5 |
radiusSrvProfileServerSharedSecretThis parameter represents the shared secret between the RADIUS server and client. It is logically treated as write-only and should return the information in asterisks.rw DisplayString .1.3.6.1.4.1.841.1.1.1.2.2.1.1.6 |
radiusSrvProfileTableEntryStatusThis parameter is used to configure the entry status of RADIUS server profile table. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.2.2.1.1.7 |
radiusSupProfileTableThis table contains the radius support profile table configurations. SEQUENCE OF RadiusSupProfileTableEntry .1.3.6.1.4.1.841.1.1.1.2.2.2 |
radiusSupProfileTableEntryThis parameter represents the entry for the radius support profile table. RadiusSupProfileTableEntry .1.3.6.1.4.1.841.1.1.1.2.2.2.1 |
radiusSupProfileTableIndexThis parameter represents the index for the radius support profile table. Each index corresponds to the one profile name in the radius server profile tablero Unsigned32 (1) .1.3.6.1.4.1.841.1.1.1.2.2.2.1.1 |
radiusSupProfileNameThis parameter represents the RADIUS profile name, only one profile is supported.rw DisplayString .1.3.6.1.4.1.841.1.1.1.2.2.2.1.2 |
radiusSupProfileMaxReTransmissionsThis parameter represents the number of times the radius request message to be sent to RADIUS server after the expiry of response time.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.2.2.2.1.3 |
radiusSupProfileMsgResponseTimeThis parameter represents the wait time in the RADIUS client for the response message from RADIUS server.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.2.2.2.1.4 |
radiusSupProfileReAuthenticationPeriodThe parameter represents the time interval within which the reauthentication of the 802.1x enabled station happens.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.2.2.2.1.5 |
radiusSupProfileTableEntryStatusThis parameter is used to configure the entry status of RADIUS supported profile table. It can be configured as active(enable) -1, notInService(disable) - 2rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.2.2.2.1.6 |
macacl OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.1.2.3 |
macaclProfileTableThis table contains the MAC access control profile configurations. SEQUENCE OF MacaclProfileTableEntry .1.3.6.1.4.1.841.1.1.1.2.3.1 |
macaclProfileTableEntryThis parameter represents the entry for the MAC access control profile table. MacaclProfileTableEntry .1.3.6.1.4.1.841.1.1.1.2.3.1.1 |
macaclProfileTableIndexUser defined profiles for MAC Access Control List. Max. number of profiles are 16.ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.2.3.1.1.1 |
macaclProfileNameThis parameter represents the unique name MAC ACL profile.rw DisplayString .1.3.6.1.4.1.841.1.1.1.2.3.1.1.2 |
macaclOperationTypeThis parameter is used o configure the type of MAC ACL profile. Select (1) to allow and (2) to deny.rw Enumeration .1.3.6.1.4.1.841.1.1.1.2.3.1.1.3 |
macaclTableEntryStatusThis parameter is used to configure the status of the security MAC ACL profile. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.2.3.1.1.4 |
macaclAddrTableThis table holds MAC access control list addresses. SEQUENCE OF MacaclAddrTableEntry .1.3.6.1.4.1.841.1.1.1.2.3.2 |
macaclAddrTableEntryThis parameter represents the entry for the MAC access control list address table. MacaclAddrTableEntry .1.3.6.1.4.1.841.1.1.1.2.3.2.1 |
macaclAddrTableIndexThis parameter represents the user defined profiles for MAC ACL Address. Max. profiles are 16 profiles.ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.2.3.2.1.1 |
macaclAddrTableSecIndexThis parameter represents the user defined secondary profiles for MAC ACL Address. Maximum entries are 64 -- one entry per stationro Unsigned32 .1.3.6.1.4.1.841.1.1.1.2.3.2.1.2 |
macaclAddrTableMACAddressThis parameter represents the valid MAC address for MAC ACL.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.2.3.2.1.3 |
macaclAddrCommentThis parameter displays a valid comment for MAC ACL Address.rw DisplayString .1.3.6.1.4.1.841.1.1.1.2.3.2.1.4 |
macaclAddrTableEntryStatusThis parameter is used to configure the status of the security MAC ACL Address. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.2.3.2.1.5 |
qos OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.1.3 |
qosProfileTableThis table holds the various profiles for QOS (quality of service) configuration. SEQUENCE OF QosProfileTableEntry .1.3.6.1.4.1.841.1.1.1.3.1 |
qosProfileTableEntryThis parameter represents the entry for the qos profile table.This table supports one entry. QosProfileTableEntry .1.3.6.1.4.1.841.1.1.1.3.1.1 |
qosProfileTableIndexThis parameter represents user defined profiles for Quality of Service (QoS).ro Unsigned32 (1) .1.3.6.1.4.1.841.1.1.1.3.1.1.1 |
qosProfileNameThis parameter displays the name of the QoS profile that has been assigned.rw DisplayString .1.3.6.1.4.1.841.1.1.1.3.1.1.2 |
qosProfileTablePolicyNameThis parameter displays the QoS Policy profile name.rw DisplayString .1.3.6.1.4.1.841.1.1.1.3.1.1.3 |
qosProfileEDCAProfileNameThis parameter displays the name for QoS EDCA profile.rw DisplayString .1.3.6.1.4.1.841.1.1.1.3.1.1.4 |
qosProfileTableQoSNACKStatusThis parameter is used to configure the status of the QoS profile ACK.rw Enumeration .1.3.6.1.4.1.841.1.1.1.3.1.1.5 |
qoSPolicyTableThis table contains the QOS policy configurations. SEQUENCE OF QoSPolicyTableEntry .1.3.6.1.4.1.841.1.1.1.3.2 |
qoSPolicyTableEntryThis parameter represents the entry for the qos policy table. QoSPolicyTableEntry .1.3.6.1.4.1.841.1.1.1.3.2.1 |
qoSPolicyTableIndexThis parameter represents user defined profiles for QoS Policy list.ro Unsigned32 (1) .1.3.6.1.4.1.841.1.1.1.3.2.1.1 |
qoSPolicyTableSecIndexThis parameter represents user defined secondary profiles. They are inbound layer2 -1, inbound layer3 -2, outbound layer2 -3 and outbound layer3 -4ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.2.1.2 |
qoSPolicyTablePolicyNameThis parameter displays the QoS policy name.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.3.2.1.3 |
qoSPolicyTypeThis parameter configures the QoS Policy type. They can be configured as the following: inbound layer2(1), inbound layer3(2), outbound layer2(3) and outbound layer3(4)ro Enumeration .1.3.6.1.4.1.841.1.1.1.3.2.1.4 |
qoSPolicyPriorityMappingThis parameter is used as the primary index to the QoS 802.1D to 802.1p mapping table.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.2.1.5 |
qoSPolicyMarkingStatusThis parameter is used to enable or disable QoS Policy markings. Select (1) to enable, (2) to disable, and (3) for not supported option.rw Enumeration .1.3.6.1.4.1.841.1.1.1.3.2.1.6 |
qoSPolicyTableEntryStatusThe parameter is used to configure the QoS Policy Table status. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.3.2.1.7 |
wirelessQoS OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.1.3.3 |
wirelessQoSEDCATableThis table holds the wireless QOS EDCA (enhanced distributed channel access) configurations. SEQUENCE OF WirelessQoSEDCATableEntry .1.3.6.1.4.1.841.1.1.1.3.3.1 |
wirelessQoSEDCATableEntryThis parameter represents the entry for the wireless QOS EDCA table. WirelessQoSEDCATableEntry .1.3.6.1.4.1.841.1.1.1.3.3.1.1 |
wirelessQoSEDCATableIndexThis parameter is user defined profiles for Wireless QoS EDCA. Max profile that user can define is 1.ro Unsigned32 (1) .1.3.6.1.4.1.841.1.1.1.3.3.1.1.1 |
wirelessQoSEDCATableSecIndexThis parameter represents the user defined secondary profiles for Wireless QoS EDCA. Maximum profiles are 4. BK -1 (back ground), BE -2 (best effort), VI -3 (video), VO -4 (voice)ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.3.1.1.2 |
wirelessQoSEDCATableProfileNameThis parameter displays the name for the Wireless QoS EDCA profile.rw DisplayString .1.3.6.1.4.1.841.1.1.1.3.3.1.1.3 |
wirelessQoSEDCATableCWminThis parameter is used to configure the CW(Contention Window) min value for the wireless QoS EDCA profile. It can be configured up to 255 value. If this value is configured lower, then this increases the priority of the access category.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.3.1.1.4 |
wirelessQoSEDCATableCWmaxThis parameter is used to configure the CW(Contention window) Max value for the wireless QoS EDCA profile. This value can be configured up to 65535. If this value id confiured to a lower value, then this increases the priority of access category.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.3.1.1.5 |
wirelessQoSEDCATableAIFSNThis parameter is used to configure the AIFSN (Arbitrary Inter Frame Space Number) value for the wireless QoS EDCA profile. It can be configured up to 15. If this value is configured lower,then this increases the priority of the access category.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.3.1.1.6 |
wirelessQoSEDCATableTXOPThis parameter is used to configure TXOP(transmission oppurtunities) value for Wireless QoS EDCA. The values can be configured up to 65535. If this value for this parameter is configured lower, then this decreases the priority of the access category.rw DisplayString .1.3.6.1.4.1.841.1.1.1.3.3.1.1.7 |
wirelessQoSEDCATableACMThis parameter is used to enable or disable the value for Addmission Control Mandatory. If ACM value is set to enable for a particular access category, then certain procedures needs to followed for using that access category.rw Enumeration .1.3.6.1.4.1.841.1.1.1.3.3.1.1.8 |
wirelessQoSEDCATableAPCWminThis parameter is used to configure the minimum value for APCWmin. It can be configured upto 32767.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.3.1.1.9 |
wirelessQoSEDCATableAPCWmaxThis parameter is used to configure the maximum value for APCWmax. It can be configured upto 32767.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.3.1.1.10 |
wirelessQoSEDCATableAPAIFSNThis parameter is used to configure the value fo APAIFSN(Arbitration Inter-Frame Space Number). The value for the APAIFSN can be configured up to 15rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.3.1.1.11 |
wirelessQoSEDCATableAPTXOPThis parameter is used to configure the APTXOP (transmission oppurtunities) for the QoS EDCA profile. If the value is set to 0, then only one MPDU or MSDU can be transmittedrw DisplayString .1.3.6.1.4.1.841.1.1.1.3.3.1.1.12 |
wirelessQoSEDCATableAPACMThis parameter is used to configure the APACM for the QoS EDCA profile. Select (1) to enable the profile and (2) to disable it.rw Enumeration .1.3.6.1.4.1.841.1.1.1.3.3.1.1.13 |
l2l3QoS OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.1.3.4 |
l2l3QoSDot1DToDot1pMappingTableThis table is used to configure Quality of Service mappings between 802.1D and 802.1p priorities. SEQUENCE OF L2l3QoSDot1DToDot1pMappingTableEntry .1.3.6.1.4.1.841.1.1.1.3.4.1 |
l2l3QoSDot1DToDot1pMappingTableEntryThis parameter represents entries in the QoS 802.1D to 802.1p Mapping Table. L2l3QoSDot1DToDot1pMappingTableEntry .1.3.6.1.4.1.841.1.1.1.3.4.1.1 |
l2l3QoSDot1DToDot1pMappingTableIndexThis parameter is used as the primary index to the QoS 802.1D to 802.1p mapping table. This is based on the QoS profile.ro Unsigned32 (1) .1.3.6.1.4.1.841.1.1.1.3.4.1.1.1 |
l2l3QoSDot1dPriorityThis parameter is used to specify the 802.1d priority and is used as the secondary index to the 802.1D to 802.1p mapping table.ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.4.1.1.2 |
l2l3QoSDot1pPriorityThis parameter is used to specify the 802.1D priority to be mapped to a 802.1p priorityrw Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.4.1.1.3 |
l2l3QoSDot1DToIPDSCPMappingTableThis table is used to configure Quality of Service mappings between 802.1D to IP DSCP (Differentiated Services Code Point) priorities. SEQUENCE OF L2l3QoSDot1DToIPDSCPMappingTableEntry .1.3.6.1.4.1.841.1.1.1.3.4.2 |
l2l3QoSDot1DToIPDSCPMappingTableEntryThis parameter represents entries in the 802.1D to IP DSCP Mapping Table. L2l3QoSDot1DToIPDSCPMappingTableEntry .1.3.6.1.4.1.841.1.1.1.3.4.2.1 |
l2l3QoSDot1DToIPDSCPMappingTableIndexThis parameter is used as the primary index to the 802.1D to IP DSCP mapping table.ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.4.2.1.1 |
l2l3QoSDot1dPriorityIPDSCPThis parameter is used to specify the 802.1D priority and is used as the secondary index to the 802.1D to IP DSCP mapping table.ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.4.2.1.2 |
l2l3QoSDSCPPriorityLowerLimitThis parameter is used to specify IP DSCP lower limit.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.4.2.1.3 |
l2l3QoSDSCPPriorityUpperLimitThis parameter is used to specify IP DSCP upper limit.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.4.2.1.4 |
worpQoS OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.1.3.5 |
worpQoSPIRMacTableThis Table holds the MAC Address details for Packet Identification Rule Clasification. SEQUENCE OF WorpQoSPIRMacTableEntry .1.3.6.1.4.1.841.1.1.1.3.5.1 |
worpQoSPIRMacTableEntryThis parameter represents the entry for the worpQoSPIRMacTable. WorpQoSPIRMacTableEntry .1.3.6.1.4.1.841.1.1.1.3.5.1.1 |
worpQoSPIRMacTableIndexThis parameter specifies the index number of the entry in the table.ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.5.1.1.1 |
worpQoSPIRMacAddrThis parameter specifies the MAC Address which can be used for PIR classification.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.3.5.1.1.2 |
worpQoSPIRMacMaskThis parameter specifies the MAC Address mask for the worpQoSPIRMacAddr.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.3.5.1.1.3 |
worpQoSPIRMacCommentThis parameter specifies the comment for the mac entry.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.3.5.1.1.4 |
worpQoSPIRMacTableEntryStatusThis parameter is used to configure the worpQoSPIRMacTable status. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.3.5.1.1.5 |
worpQoSPIRIPTableThis Table holds the IP Address details for PIR (Packet Identification Rule) Clasification. SEQUENCE OF WorpQoSPIRIPTableEntry .1.3.6.1.4.1.841.1.1.1.3.5.2 |
worpQoSPIRIPTableEntryThis parameter represents the entry for the worpQoSPIRIPTable. WorpQoSPIRIPTableEntry .1.3.6.1.4.1.841.1.1.1.3.5.2.1 |
worpQoSPIRIPTableIndexThis parameter specifies the index number of the entry in the table.ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.5.2.1.1 |
worpQoSPIRIPAddrThis parameter specifies the IP Address which can be used for PIR classification.rw IpAddress .1.3.6.1.4.1.841.1.1.1.3.5.2.1.2 |
worpQoSPIRIPSubMaskThis parameter specifies the Subnet Mask for the worpQoSPIRIPAddr.rw IpAddress .1.3.6.1.4.1.841.1.1.1.3.5.2.1.3 |
worpQoSPIRIPCommentThis parameter specifies the comment for the IP Address entry.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.3.5.2.1.4 |
worpQoSPIRIPTableEntryStatusThis parameter is used to configure the worpQoSPIRIPTable status. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.3.5.2.1.5 |
worpQoSPIRPortTableThis Table holds the TCP/UDP Port details for PIR (Packet Identification Rule) Clasification. SEQUENCE OF WorpQoSPIRPortTableEntry .1.3.6.1.4.1.841.1.1.1.3.5.3 |
worpQoSPIRPortTableEntryThis parameter represents the entry for the worpQoSPIRPortTable. WorpQoSPIRPortTableEntry .1.3.6.1.4.1.841.1.1.1.3.5.3.1 |
worpQoSPIRPortTableIndexThis parameter specifies the index number of the entry in the table.ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.5.3.1.1 |
worpQoSPIRStartPortThis parameter specifies the Starting TCP/UDP Port Number which can be used for PIR classification.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.5.3.1.2 |
worpQoSPIREndPortThis parameter specifies the Ending TCP/UDP Port Number which can be used for PIR classification.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.5.3.1.3 |
worpQoSPIRPortCommentThis parameter specifies the comment for the TCP/UDP Port entry.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.3.5.3.1.4 |
worpQoSPIRPortTableEntryStatusThis parameter is used to configure the worpQoSPIRPortTable status. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.3.5.3.1.5 |
worpQoSPIRMapTableThis Table holds the Mapping information between PIR MAC Table entries, PIR IP Table entries, PIR Port Table entries with PIR Table. SEQUENCE OF WorpQoSPIRMapTableEntry .1.3.6.1.4.1.841.1.1.1.3.5.4 |
worpQoSPIRMapTableEntryThis table represents the entry for the worpQoSPIRMapTable. WorpQoSPIRMapTableEntry .1.3.6.1.4.1.841.1.1.1.3.5.4.1 |
worpQoSPIRMapTableIndexThis parameter specifies the index number of the entry in the table.ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.5.4.1.1 |
worpQoSPIRMapRuleNameThis parameter specifies the PIR Rule name corresponds to this index.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.3.5.4.1.2 |
worpQoSPIRMapSrcMacIndexListThis parameter specifies the Source MAC Address Classification for the PIR Rule. This is a display string consists of index number of the PIR MAC Table entries with comma seperated. Value 0 indicates that this list is disabled.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.3.5.4.1.3 |
worpQoSPIRMapDstMacIndexListThis parameter specifies the Destination MAC Address Classification for the PIR Rule. This is a display string consists of index number of the PIR MAC Table entries with comma seperated. Value 0 indicates that this list is disabled.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.3.5.4.1.4 |
worpQoSPIRMapSrcIpAddrIndexListThis parameter specifies the Source IP Address Classification for the PIR Rule. This is a display string consists of index number of the PIR MAC Table entries with comma seperated. Value 0 indicates that this list is disabled.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.3.5.4.1.5 |
worpQoSPIRMapDstIpAddrIndexListThis parameter specifies the Destination IP Address Classification for the PIR Rule. This is a display string consists of index number of the PIR MAC Table entries with comma seperated. Value 0 indicates that this list is disabled.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.3.5.4.1.6 |
worpQoSPIRMapSrcPortIndexListThis parameter specifies the Source TCP/UDP Port Classification for the PIR Rule. This is a display string consists of index number of the PIR MAC Table entries with comma seperated. Value 0 indicates that this list is disabled.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.3.5.4.1.7 |
worpQoSPIRMapDstPortIndexListThis parameter specifies the Destination TCP/UDP Port Classification for the PIR Rule. This is a display string consists of index number of the PIR MAC Table entries with comma seperated. Value 0 indicates that this list is disabled.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.3.5.4.1.8 |
worpQoSPIRTableThis Table holds the Packet Identification Rule(PIR) information for QoS feature. SEQUENCE OF WorpQoSPIRTableEntry .1.3.6.1.4.1.841.1.1.1.3.5.5 |
worpQoSPIRTableEntryThis parameter represents the entry for the worpQoSPIRTable. WorpQoSPIRTableEntry .1.3.6.1.4.1.841.1.1.1.3.5.5.1 |
worpQoSPIRTableIndexThis parameter specifies the index number of the entry in the table.ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.5.5.1.1 |
worpQoSPIRRuleNameThis parameter specifies the Packet Identification Rule(PIR) Name.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.3.5.5.1.2 |
worpQoSPIRRuleBitMaskThis parameter specifies which Packet classification rules are enabled. It is a Bit Mask field. Bits are defined as follows Bit0 - Dst MAC rule Enabled. Bit1 - Src MAC rule Enabled. Bit2 - Prity rule Enabled. Bit3 - Vlan ID rule Enabled. Bit4 - Ether value rule Enabled. Bit5 - ToS rule Enabled. Bit6 - IP PROTOCOL rule Enabled. Bit7 - Dst IP Addr rule Enabled. Bit8 - Src IP Addr rule Enabled. Bit9 - Dst Port rule Enabled. Bit10 - Src Port rule Enabled. Bit11 - PPPoE Encapsulation rule Enabled.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.5.5.1.3 |
worpQoSPIRIPToSLowThis Parameter specifies the lower limit for the ToS (Types Of Service) classification.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.5.5.1.4 |
worpQoSPIRIPToSHighThis Parameter specifies the higher limit for the ToS classification.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.5.5.1.5 |
worpQoSPIRIPToSMaskThis Parameter specifies The ToS Mask which will be used to perform bitwise and operation with incoming Packet's ToS values and it will be checked again Lower & Hight limit the ToS Low, ToS High configuraiton.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.5.5.1.6 |
worpQoSPIRIPProtocolIdsThis Parameter specifies the Protocol Classification for the incoming packet.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.3.5.5.1.7 |
worpQoSPIREtherPriorityLowThis parameter specifies the lower limit for the 802.1p classificaiton for the incoming packet.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.5.5.1.8 |
worpQoSPIREtherPriorityHighThis parameter specifies the Higher limit for the 802.1p classificaiton for the incoming packet.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.5.5.1.9 |
worpQoSPIRVlanIdThis parameter specifies the VLAN classification for the incoming packet.rw VlanId .1.3.6.1.4.1.841.1.1.1.3.5.5.1.10 |
worpQoSPIREtherTypeThis parameter specifies the Ether type classification for the incoming ethernet frame.rw Enumeration .1.3.6.1.4.1.841.1.1.1.3.5.5.1.11 |
worpQoSPIREtherValueThis parameter specifies the Ether Value classificaiton for the incoming ethernet frame.rw OCTET STRING .1.3.6.1.4.1.841.1.1.1.3.5.5.1.12 |
worpQoSPIRPPPoEEncapsulationThis parameter specifies the PPPoE (Point-to-point Protocol Over Ethernet) Encapsulation status for the incoming ethernet frame.rw Enumeration .1.3.6.1.4.1.841.1.1.1.3.5.5.1.13 |
worpQoSPIRPPPoEProtocolIdThis parameter specifies the protocol id inside the PPPoE Encapsulation data for the incoming ethernet frame.rw OCTET STRING .1.3.6.1.4.1.841.1.1.1.3.5.5.1.14 |
worpQoSPIRMapTableIndexValThis parameter specifies the index of the worpQoSPIRMapTable.ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.5.5.1.15 |
worpQoSPIRTableEntryStatusThis parameter is used to configure the worpQoSPIRTable status. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.3.5.5.1.16 |
worpQoSSFClassTableThis Table holds the Service Flow Classification (SFC) information for QoS feature. SEQUENCE OF WorpQoSSFClassTableEntry .1.3.6.1.4.1.841.1.1.1.3.5.6 |
worpQoSSFClassTableEntryThis parameter represents the entry for the worpQoSSFClassTable. WorpQoSSFClassTableEntry .1.3.6.1.4.1.841.1.1.1.3.5.6.1 |
worpQoSSFClassTableIndexThis parameter specifies the index number of the entry in the worpQoSSFClassTable.ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.5.6.1.1 |
worpQoSSFClassNameThis parameter specifies the Service Flow Class Name.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.3.5.6.1.2 |
worpQoSSFClassSchedularTypeThis parameter specifies the type of Scheduler to be used for this Service Flow. Select 1 for rtps - Real Time Polling Service 2 for be - Best Effort.rw Enumeration .1.3.6.1.4.1.841.1.1.1.3.5.6.1.3 |
worpQoSSFClassDirectionThis parameter specifies the Direction of the Service Flow.rw Enumeration .1.3.6.1.4.1.841.1.1.1.3.5.6.1.4 |
worpQoSSFClassStatusThis parameter specifies the Status of the Service Flow.ro Enumeration .1.3.6.1.4.1.841.1.1.1.3.5.6.1.5 |
worpQoSSFClassMIRThis parameter specifies the Maximum Information Rate(MIR) for this Service Flow. This value is represented in Kbps.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.5.6.1.6 |
worpQoSSFClassCIRThis parameter specifies the Comitted Information Rate(CIR) for this Service Flow. This value is represented in Kbps.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.5.6.1.7 |
worpQoSSFClassMaxLatencyThis parameter specifies the Latency for this Service Flow. This is represented in milliseconds.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.5.6.1.8 |
worpQoSSFClassTolerableJitterThis parameter specifies the Jitter for this Service Flow. This is represented in milliseconds.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.5.6.1.9 |
worpQoSSFClassTrafficPriorityThis parameter specifies the priority of execution of the Service Flow inside a QoS Class.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.5.6.1.10 |
worpQoSSFClassNumOfMesgInBurstThis parameter specifies the Number of maximum messages can be sent in a single burst.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.5.6.1.11 |
worpQoSSFClassTableEntryStatusThis parameter is used to configure the worpQoSSFClassTable status. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.3.5.6.1.12 |
worpQoSClassTableThis Table holds the Class information for QoS feature. SEQUENCE OF WorpQoSClassTableEntry .1.3.6.1.4.1.841.1.1.1.3.5.7 |
worpQoSClassTableEntryThis parameter represents the entry for the worpQoSClassTable. WorpQoSClassTableEntry .1.3.6.1.4.1.841.1.1.1.3.5.7.1 |
worpQoSClassTableIndexThis parameter specifies the QoS Class index.ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.5.7.1.1 |
worpQoSClassSFCTableIndexThis parameter specifies the SFC index within the QoS Class index.ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.5.7.1.2 |
worpQoSClassPIRTableIndexThis parameter specifies the PIR index within the QoS SFC index.ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.5.7.1.3 |
worpQoSClassSFCValueThis parameter specifies the reference index of the QoS SFC Table index.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.5.7.1.4 |
worpQoSClassPIRValueThis parameter specifies the reference index of the QoS PIR Table index.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.5.7.1.5 |
worpQoSClassNameThis parameter specifies the QoS Class Name.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.3.5.7.1.6 |
worpQoSClassPriorityThis parameter specifies the PIR Execution priority within a QoS Classrw Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.5.7.1.7 |
worpQoSClassTableEntryStatusThis parameter is used to configure the worpQoSClassTable status. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.3.5.7.1.8 |
worpQoSSUTableThis Table holds the SU/End Point B entries for QoS feature. SEQUENCE OF WorpQoSSUTableEntry .1.3.6.1.4.1.841.1.1.1.3.5.8 |
worpQoSSUTableEntryThis parameter represents the entry for the worpQoSSUTable. WorpQoSSUTableEntry .1.3.6.1.4.1.841.1.1.1.3.5.8.1 |
worpQoSSUTableIndexThis parameter specifies the index number of the entry in the tablero Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.5.8.1.1 |
worpQoSSUMACAddressThis parameter specifies the wireless MAC Address of the SU or End Point Brw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.3.5.8.1.2 |
worpQoSSUQoSClassIndexThis parameter specifies the reference index of the QoS Class Table index.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.5.8.1.3 |
worpQoSSUCommentThis parameter specifies the comment for this entry.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.3.5.8.1.4 |
worpQoSSUTableEntryStatusThis parameter is used to configure the worpQoSSUTable status. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.3.5.8.1.5 |
worpQoSDefaultClassThis parameter specifies the QoS Class need to be used by the SU/End Point B connected to BSU/End Point A but not listed in the worpQoSSUTable.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.5.9 |
worpQoSL2BroadcastClassThis parameter specifies the QoS Class need to be used for the Layer 2 Broadcast traffic on the Downlink direction.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.3.5.10 |
network OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.1.4 |
netIp OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.1.4.1 |
netIpCfgTableThis table is used to configure the network IP parameters. SEQUENCE OF NetIpCfgTableEntry .1.3.6.1.4.1.841.1.1.1.4.1.1 |
netIpCfgTableEntryThis table represents the entry for the network IP configuration table NetIpCfgTableEntry .1.3.6.1.4.1.841.1.1.1.4.1.1.1 |
netIpCfgTableIndexThis parameter represents the index for the network IP configuration table and interface number.ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.4.1.1.1.1 |
netIpCfgIPAddressThis parameter is used to configure the IP Address for the ethernet interface.rw IpAddress .1.3.6.1.4.1.841.1.1.1.4.1.1.1.2 |
netIpCfgSubnetMaskThis parameter is used to configure the subnet mask for the ethernet interface.rw IpAddress .1.3.6.1.4.1.841.1.1.1.4.1.1.1.3 |
netIpCfgDefaultRouterIPAddressThis parameter is used to set the IP address of the gateway or router of the device. This parameter is deprecated and please use the object netCfgAllIntfDefaultRouterIpAddr to set the gateway IP address.rwdeprecated IpAddress .1.3.6.1.4.1.841.1.1.1.4.1.1.1.4 |
netIpCfgAddressTypeThis parameter is used to specify whether the device network paramenters are to be configured through a dhcp client or to be assigned statically. If the value is set to 1, then the device is configured as static. If the value is set to 2, then the device is set to dynamic.rw Enumeration .1.3.6.1.4.1.841.1.1.1.4.1.1.1.5 |
netIpWirelessCfgTableThis table is used to configure the wireless network IP parameters in routing mode. SEQUENCE OF NetIpWirelessCfgTableEntry .1.3.6.1.4.1.841.1.1.1.4.1.2 |
netIpWirelessCfgTableEntryThis table represents the entry for the network IP configuration table NetIpWirelessCfgTableEntry .1.3.6.1.4.1.841.1.1.1.4.1.2.1 |
netIpWirelessCfgTableIndexThis parameter is user defined index or interface number in the network IP wireless configuration table.ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.4.1.2.1.1 |
netIpWirelessCfgIPAddressThis parameter is used to configure the IP Address for the wireless interface.rw IpAddress .1.3.6.1.4.1.841.1.1.1.4.1.2.1.2 |
netIpWirelessCfgSubnetMaskThis parameter is used to configure the subnet mask for the wireless interface.rw IpAddress .1.3.6.1.4.1.841.1.1.1.4.1.2.1.3 |
netIpStaticRouteTableThis table is used to configure the static routes in routing mode. SEQUENCE OF NetIpStaticRouteTableEntry .1.3.6.1.4.1.841.1.1.1.4.1.3 |
netIpStaticRouteTableEntryThis parameter represents the entry status for the netIpStaticRouteTable and this table holds upto 256 entries. NetIpStaticRouteTableEntry .1.3.6.1.4.1.841.1.1.1.4.1.3.1 |
netIpStaticRouteTableIndexThis parameter represents the index of the netIpStaticRouteTable.ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.4.1.3.1.1 |
netIpStaticRouteDestAddrThis parameter is used to enter the destination IP address for which the static route is to be made.rw IpAddress .1.3.6.1.4.1.841.1.1.1.4.1.3.1.2 |
netIpStaticRouteMaskThis parameter is used to enter the mask for the destination address.rw IpAddress .1.3.6.1.4.1.841.1.1.1.4.1.3.1.3 |
netIpStaticRouteNextHopThis parameter represents the next reachable hop using which route is made to the destination IP address.rw IpAddress .1.3.6.1.4.1.841.1.1.1.4.1.3.1.4 |
netIpStaticRouteMetricThis parameter represents the Metric, i.e.,the 'distance' to the target (usually counted in hops).rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.4.1.3.1.5 |
netIpStaticRouteTableEntryStatusThis parameter is used to configure the netIpStaticRouteTable status. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.4.1.3.1.6 |
netCfg OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.1.4.2 |
netCfgClearIntfStatsThis parameter is used to clear the wired/wireless interface statistics.rw Enumeration .1.3.6.1.4.1.841.1.1.1.4.2.1 |
netCfgAllIntfDefaultRouterAddrDefault Router Address that applies to all interfaces.rw IpAddress .1.3.6.1.4.1.841.1.1.1.4.2.2 |
netCfgSupportedInterfacesThis parameter shows the names of supported interfaces depending on the network mode.ro DisplayString .1.3.6.1.4.1.841.1.1.1.4.2.3 |
netCfgStaticRouteStatusThis parameter is used to enable/disable the static routes option.rw Enumeration .1.3.6.1.4.1.841.1.1.1.4.2.4 |
wirelessInActivityTimerThis parameter is used to monitor the wireless interface for every specified number of minutes. The value 0 disables monitoring.rwdeprecated Unsigned32 .1.3.6.1.4.1.841.1.1.1.4.2.5 |
ethernetInActivityTimerThis parameter is used to monitor the ethernet interface for every specified number of minutes. The value 0 disables monitoring.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.4.2.6 |
netCfgPrimaryDNSIpAddressThis parameter is to configure the Primary DNS IP Address to be used by this product.rw IpAddress .1.3.6.1.4.1.841.1.1.1.4.2.7 |
netCfgSecondaryDNSIpAddressThis parameter is to configure the Secondary DNS IP Address to be used by this product.rw IpAddress .1.3.6.1.4.1.841.1.1.1.4.2.8 |
wirelessInActivityTimerInSecsThis parameter is used to monitor the wireless interface for every specified number of seconds. The value 0 disables monitoring. It can be configured from 5 to 600 seconds.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.4.2.9 |
nat OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.1.4.3 |
natStatusThis parameter is used to configure the NAT(Network Address Translation) status.rw Enumeration .1.3.6.1.4.1.841.1.1.1.4.3.1 |
natPortBindingStatusThis parameter is used to enable or disable static bind entries on the NAT device.rw Enumeration .1.3.6.1.4.1.841.1.1.1.4.3.2 |
natStaticPortBindTableThis table is used to configure NAT Port bind specific information. SEQUENCE OF NatStaticPortBindTableEntry .1.3.6.1.4.1.841.1.1.1.4.3.3 |
natStaticPortBindTableEntryThis parameter represents an entry in the NAT Static Port Bind Table. NatStaticPortBindTableEntry .1.3.6.1.4.1.841.1.1.1.4.3.3.1 |
natStaticPortBindTableIndexThis parameter is used as the index for the NAT static Port bind table.ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.4.3.3.1.1 |
natStaticPortBindLocalAddrThis parameter represents the local IP address for this NAT Static Port bind Table entry.rw IpAddress .1.3.6.1.4.1.841.1.1.1.4.3.3.1.2 |
natStaticPortBindPortTypeThis parameter represents the port type for this NAT Static Port bind Table entry.rw Enumeration .1.3.6.1.4.1.841.1.1.1.4.3.3.1.3 |
natStaticPortBindStartPortNumThis parameter represents the start port number for this NAT Static Port bind Table entry.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.4.3.3.1.4 |
natStaticPortBindEndPortNumThis parameter represents the end port number for this NAT Static Port bind Table entry.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.4.3.3.1.5 |
natStaticPortBindTableEntryStatusThis parameter is used to configure the natStaticPortBindTable status. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.4.3.3.1.6 |
rip OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.1.4.4 |
ripConfigStatusThis parameter is used to configure the RIP configuration status.rw Enumeration .1.3.6.1.4.1.841.1.1.1.4.4.1 |
ripConfigTableThis table is used to configure the RIP configuration information. SEQUENCE OF RipConfigTableEntry .1.3.6.1.4.1.841.1.1.1.4.4.2 |
ripConfigTableEntryThis parameter represents the entry for the ripConfigTable. RipConfigTableEntry .1.3.6.1.4.1.841.1.1.1.4.4.2.1 |
ripConfigTableIndexThis parameter represents the index for ripConfigTable.ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.4.4.2.1.1 |
ripInterfaceNameThis parameter shows the available interfaces for which the rip can be configured.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.4.4.2.1.2 |
ripInterfaceStatusThis parameter is used to enable/disable the rip for the particular interface.rw Enumeration .1.3.6.1.4.1.841.1.1.1.4.4.2.1.3 |
ripInterfaceAuthTypeThis parameter represents the authentication type used for rip configuration.rw Enumeration .1.3.6.1.4.1.841.1.1.1.4.4.2.1.4 |
ripInterfaceAuthKeyThis parameter is used to configure the authentication key for the authentication type.rw DisplayString .1.3.6.1.4.1.841.1.1.1.4.4.2.1.5 |
ripInterfaceVersionNumThis parameters allows to configure the rip version verion.rw Enumeration .1.3.6.1.4.1.841.1.1.1.4.4.2.1.6 |
ripReceiveOnlyThis parameter allows to configure the interface to receive only RIP version 1 and/or RIP verison 2 packets.rw Enumeration .1.3.6.1.4.1.841.1.1.1.4.4.2.1.7 |
vlan OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.1.5 |
vlanStatusThis parameter is used to configure the VLAN functionality. Select 1 to enable the VLAN functionality and 2 to disable the VLAN functionality.rw Enumeration .1.3.6.1.4.1.841.1.1.1.5.1 |
mgmtVLANIdentifierThis parameter represents the management VLAN Identifier (ID).rw VlanId .1.3.6.1.4.1.841.1.1.1.5.2 |
mgmtVLANPriorityThis parameter represents the management VLAN priority, giving eight (2^3) priority levels with the highest priority as seven.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.5.3 |
vlanEthCfgTableThis table is used to configure the VLAN parameters for the ethernet interface. SEQUENCE OF VlanEthCfgTableEntry .1.3.6.1.4.1.841.1.1.1.5.4 |
vlanEthCfgTableEntryThis parameter represents the entry for the Vlan Configuration table. VlanEthCfgTableEntry .1.3.6.1.4.1.841.1.1.1.5.4.1 |
vlanEthCfgTableIndexThis parameter represents the physical interface and used as index to this table.ro Unsigned32 (1) .1.3.6.1.4.1.841.1.1.1.5.4.1.1 |
vlanModeThis parameter is used to set the VLAN Mode for the physical interface.rw Enumeration .1.3.6.1.4.1.841.1.1.1.5.4.1.2 |
accessVLANIdThis parameter is used to set the access VlanId for the physical interface.rw VlanId .1.3.6.1.4.1.841.1.1.1.5.4.1.3 |
accessVLANPriorityThis parameter is used to set the access Vlan priority, which varies from 0 to 7 with 7 having highest priority.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.5.4.1.4 |
untaggedFramesThis parameter is used to set the option to allow the untagged frames.rw Enumeration .1.3.6.1.4.1.841.1.1.1.5.4.1.5 |
vlanEthTrunkTableThis table is used to configure the VLAN trunk parameters for ethernet interface. SEQUENCE OF VlanEthTrunkTableEntry .1.3.6.1.4.1.841.1.1.1.5.5 |
vlanEthTrunkTableEntryThis parameter represents the entry for the Vlan Trunk Configuration table. VlanEthTrunkTableEntry .1.3.6.1.4.1.841.1.1.1.5.5.1 |
vlanEthTrunkTableIndexThis parameter represents the vlan trunk table index and also represents the ethernet interface.ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.5.5.1.1 |
vlanEthTrunkTableSecIndexThis parameter represents the trunk table secondary index.ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.5.5.1.2 |
ethVLANTrunkIdThis parameter is used to set the trunk id.rw VlanId .1.3.6.1.4.1.841.1.1.1.5.5.1.3 |
vlanEthTrunkTableEntryStatusThis parameter is used to configure the vlan trunk table status. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.5.5.1.4 |
filtering OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.1.6 |
filteringCtrlThis parameter stores the information whether the Global Filterng is Enabled or Disabled. If this parameter is set to enabled, then the filtering is enabled. If this parameter is disabled, then filtering will be disabled. Select 1 to enable this parameter and 2 to disable this parameter.rw Enumeration .1.3.6.1.4.1.841.1.1.1.6.1 |
intraBSSFilteringThis parameter controls the wireless to wireless communication. If this parameter is set to enabled, then wireless to wireless communication is not allowed. If this parameter is set disabled, then wireless to wireless communication is allowed. Select 1 to enable the wireless to wireless communication and 2 to disable wireless to wireless communication.rw Enumeration .1.3.6.1.4.1.841.1.1.1.6.2 |
protocolFilter OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.1.6.3 |
etherProtocolFilteringCtrlThis parameter is used to configure the interface. By default, the parameter is set to disabled. The filter can be enabled either for Ethernet, Wireless or All Interface. Select 1 for ethernet, 2 for wireless, 3 for all interfaces and 4 for disable.rw Enumeration .1.3.6.1.4.1.841.1.1.1.6.3.1 |
etherProtocolFilteringTypeIf the specific protocol is not available in the ethernet protocol table, then this parameter specifies the action that needs to be taken on the packet. If this parameter is set to passthru (1), then specific protocol will be allowed. If this parameter is set to block (2), then specific protocol will be denied.rw Enumeration .1.3.6.1.4.1.841.1.1.1.6.3.2 |
etherProtocolFilterTableThis table contains the two byte hexadecimal values of the protocols. The packets whose protocol field matches with any of the entries in this table will be forwarded or dropped. SEQUENCE OF EtherProtocolFilterTableEntry .1.3.6.1.4.1.841.1.1.1.6.3.3 |
etherProtocolFilterTableEntryThis parameter represents an entry in the protocol filter table. This table supports upto 64 entries. EtherProtocolFilterTableEntry .1.3.6.1.4.1.841.1.1.1.6.3.3.1 |
etherProtocolFilterTableIndexThis parameter represents the index of the ethernet protocol Filtering table.ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.6.3.3.1.1 |
etherProtocolFilterProtocolNameThis parameter represents a two byte hexadecimal value for the Ethernet protocol to be filtered.rw DisplayString .1.3.6.1.4.1.841.1.1.1.6.3.3.1.2 |
etherProtocolFilterProtocolNumberThis parameter represents the value in the protocol field of the Ethernet packet. The value is of 4-digit Hex format. Example: The value of IP protocol is 0800. The value of ARP protocol is 0806.rw OCTET STRING .1.3.6.1.4.1.841.1.1.1.6.3.3.1.3 |
etherprotocolFilterStatusThis parameter is used to configure the status of the ethernet protocol filtering. Select 1 to block, 2 to passthru.rw Enumeration .1.3.6.1.4.1.841.1.1.1.6.3.3.1.4 |
etherProtocolFilterTableStatusThis parameter is used to configure the ethernet protocol filtering table status. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.6.3.3.1.5 |
staticMACAddrFilter OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.1.6.4 |
staticMACAddrFilterTableThis table provides the MAC address of the stations on the wired and the wireless interface; the MAC addresses will be given in pairs. Stations listed in the Static MAC Address filter will have no traffic forwarded by the device. This way Multicast traffic exchanged between stations or servers can be prevented, from being transmitted over the wireless medium when both stations are actually located on the wired backbone. SEQUENCE OF StaticMACAddrFilterTableEntry .1.3.6.1.4.1.841.1.1.1.6.4.1 |
staticMACAddrFilterTableEntryThis parameter identifies the entry in the Static MAC address filter table. This table support upto 200 entries. StaticMACAddrFilterTableEntry .1.3.6.1.4.1.841.1.1.1.6.4.1.1 |
staticMACAddrFilterTableIndexThis parameter is user defined that represents the index of the Static MAC Filtering table.ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.6.4.1.1.1 |
staticMACAddrFilterWiredMACAddressThis parameter represents the MAC address of the station on the wired interface of the device.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.6.4.1.1.2 |
staticMACAddrFilterWiredMACMaskThis parameter represents the MAC address of the filter wired MASK.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.6.4.1.1.3 |
staticMACAddrFilterWirelessMACAddressThis parameter represents the MAC address for the wireless interface.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.6.4.1.1.4 |
staticMACAddrFilterWirelessMACMaskThis parameter represents the mask for the wireless interface MAC address.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.6.4.1.1.5 |
staticMACAddrFilterCommentThis parameter is used for an optional comment associated to the staticMACAddrFilter entry.rw DisplayString .1.3.6.1.4.1.841.1.1.1.6.4.1.1.6 |
staticMACAddrFilterTableEntryStatusThis parameter is used to configure the status of the staticMACAddrFilterTable. Select It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.6.4.1.1.7 |
advancedFiltering OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.1.6.5 |
advancedFilterTableThis table is used to configure the advanced filtering using protocol name and direction. SEQUENCE OF AdvancedFilterTableEntry .1.3.6.1.4.1.841.1.1.1.6.5.1 |
advancedFilterTableEntryThis parameter represents the entry for advancedFilterTable. This table supports up to 5 entries. AdvancedFilterTableEntry .1.3.6.1.4.1.841.1.1.1.6.5.1.1 |
advancedFilterTableIndexThis parameter represents the index of the advanced filtering table.ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.6.5.1.1.1 |
advancedFilterProtocolNameThis parameter represents the protocol name to be filtered. (DenyIPX RIP, Deny IPX SAP, Deny IPX LSP, Deny IP Broadcasts, Deny IP Multicasts)ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.6.5.1.1.2 |
advancedFilterDirectionThis parameter represents the direction of the individual entry in the advanced filter table. The direction can be enabled either for Ethernet to Wireless, Wireless to Ethernet or both. Select 1 for ethernet2wireless, 2 for wireless2ethernet, 3 for both.rw Enumeration .1.3.6.1.4.1.841.1.1.1.6.5.1.1.3 |
advancedFilterTableEntryStatusThis parameter is used to configure the row status of the advanced filtering table. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.6.5.1.1.4 |
tcpudpPortFilter OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.1.6.6 |
tcpudpPortFilterCtrlThis parameter is used to configure the Tcp Udp Port Filtering. Select 1 to enable and 2 to disable the Tcp Udp Port Filtering.rw Enumeration .1.3.6.1.4.1.841.1.1.1.6.6.1 |
tcpudpPortFilterTableThis table contains the configurations for the Tcp Udp Port Filtering table. SEQUENCE OF TcpudpPortFilterTableEntry .1.3.6.1.4.1.841.1.1.1.6.6.2 |
tcpudpPortFilterTableEntryThis parameter represents the entry for tcpudpPortFilterTable. This table supports up to 64 entries. TcpudpPortFilterTableEntry .1.3.6.1.4.1.841.1.1.1.6.6.2.1 |
tcpudpPortFilterTableIndexThis parameter is used as index for the TcpUdp port filter table.ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.6.6.2.1.1 |
tcpudpPortFilterProtocolNameThis parameter represents the protocol name for the tcpudpPortFilter.rw DisplayString .1.3.6.1.4.1.841.1.1.1.6.6.2.1.2 |
tcpudpPortFilterPortNumberThis parameter represents the Port number for the tcpudpPortFilter.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.6.6.2.1.3 |
tcpudpPortFilterPortTypeThis parameter represents the port type for this TcpUdp Port filter table. The parameter can be either TCP or UDP or TCP/UDP. Select 1 for TCP, 2 for UDP and 3 for both.rw Enumeration .1.3.6.1.4.1.841.1.1.1.6.6.2.1.4 |
tcpudpPortFilterInterfaceThis parameter is used to configure the interface. By default, the parameter is set to All Interfaces. The filter can be enabled either for Ethernet, Wireless or All Interface. Select 1 for only Ethernet, 2 for only Wireless and 3 for allInterfaces.rw Enumeration .1.3.6.1.4.1.841.1.1.1.6.6.2.1.5 |
tcpudpPortFilterTableEntryStatusThe parameter indicates the status of the TCP/UDP portfilter table entry. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6)rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.6.6.2.1.6 |
worpIntraCellBlocking OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.1.6.7 |
worpIntraCellBlockingStatusThis parameter is used to enable/disable IntraCell Blocking/Filtering.rw Enumeration .1.3.6.1.4.1.841.1.1.1.6.7.1 |
worpIntraCellBlockingMACTableThe MAC table entries for IntraCell Blocking filters. This table can hold up to a maximum of 250 entries. SEQUENCE OF WorpIntraCellBlockingMACTableEntry .1.3.6.1.4.1.841.1.1.1.6.7.2 |
worpIntraCellBlockingMACTableEntryThis parameter represents the entry in the IntraCell Blocking MAC Table. WorpIntraCellBlockingMACTableEntry .1.3.6.1.4.1.841.1.1.1.6.7.2.1 |
worpIntraCellBlockingMACTableIndexThis parameter is used as the index to the IntraCell Blocking MAC Table.ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.6.7.2.1.1 |
worpIntraCellBlockingMACAddressThis parameter represents the MAC address of the SU which is allowed to communicate with other SUs with the same group ID.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.6.7.2.1.2 |
worpIntraCellBlockingGroupID1This parameter enables to segregate the SUs for intra/ inter cell communications.rw Enumeration .1.3.6.1.4.1.841.1.1.1.6.7.2.1.3 |
worpIntraCellBlockingGroupID2This parameter enables to segregate the SUs for intra/ inter cell communications.rw Enumeration .1.3.6.1.4.1.841.1.1.1.6.7.2.1.4 |
worpIntraCellBlockingGroupID3This parameter enables to segregate the SUs for intra/ inter cell communications.rw Enumeration .1.3.6.1.4.1.841.1.1.1.6.7.2.1.5 |
worpIntraCellBlockingGroupID4This parameter enables to segregate the SUs for intra/ inter cell communications.rw Enumeration .1.3.6.1.4.1.841.1.1.1.6.7.2.1.6 |
worpIntraCellBlockingGroupID5This parameter enables to segregate the SUs for intra/ inter cell communications.rw Enumeration .1.3.6.1.4.1.841.1.1.1.6.7.2.1.7 |
worpIntraCellBlockingGroupID6This parameter enables to segregate the SUs for intra/ inter cell communications.rw Enumeration .1.3.6.1.4.1.841.1.1.1.6.7.2.1.8 |
worpIntraCellBlockingGroupID7This parameter enables to segregate the SUs for intra/ inter cell communications.rw Enumeration .1.3.6.1.4.1.841.1.1.1.6.7.2.1.9 |
worpIntraCellBlockingGroupID8This parameter enables to segregate the SUs for intra/ inter cell communications.rw Enumeration .1.3.6.1.4.1.841.1.1.1.6.7.2.1.10 |
worpIntraCellBlockingGroupID9This parameter enables to segregate the SUs for intra/ inter cell communications.rw Enumeration .1.3.6.1.4.1.841.1.1.1.6.7.2.1.11 |
worpIntraCellBlockingGroupID10This parameter enables to segregate the SUs for intra/ inter cell communications.rw Enumeration .1.3.6.1.4.1.841.1.1.1.6.7.2.1.12 |
worpIntraCellBlockingGroupID11This parameter enables to segregate the SUs for intra/ inter cell communications.rw Enumeration .1.3.6.1.4.1.841.1.1.1.6.7.2.1.13 |
worpIntraCellBlockingGroupID12This parameter enables to segregate the SUs for intra/ inter cell communications.rw Enumeration .1.3.6.1.4.1.841.1.1.1.6.7.2.1.14 |
worpIntraCellBlockingGroupID13This parameter enables to segregate the SUs for intra/ inter cell communications.rw Enumeration .1.3.6.1.4.1.841.1.1.1.6.7.2.1.15 |
worpIntraCellBlockingGroupID14This parameter enables to segregate the SUs for intra/ inter cell communications.rw Enumeration .1.3.6.1.4.1.841.1.1.1.6.7.2.1.16 |
worpIntraCellBlockingGroupID15This parameter enables to segregate the SUs for intra/ inter cell communications.rw Enumeration .1.3.6.1.4.1.841.1.1.1.6.7.2.1.17 |
worpIntraCellBlockingGroupID16This parameter enables to segregate the SUs for intra/ inter cell communications.rw Enumeration .1.3.6.1.4.1.841.1.1.1.6.7.2.1.18 |
worpIntraCellBlockingMACTableEntryStatusThis parameter is used to configure the row status for the worp Intra cell blocking MAC table. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.6.7.2.1.19 |
worpIntraCellBlockingGroupTableThis table holds the group entries for IntraCell Blocking. SEQUENCE OF WorpIntraCellBlockingGroupTableEntry .1.3.6.1.4.1.841.1.1.1.6.7.3 |
worpIntraCellBlockingGroupTableEntryThis parameter represents the entry in the IntraCell Blocking Group Table. This table can contain a maximum of 16 entries. WorpIntraCellBlockingGroupTableEntry .1.3.6.1.4.1.841.1.1.1.6.7.3.1 |
worpIntraCellBlockingGroupTableIndexThis parameter is used as the index to the IntraCell Blocking Group Table.ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.6.7.3.1.1 |
worpIntraCellBlockingGroupNameThis parameter represents the group name.rw DisplayString .1.3.6.1.4.1.841.1.1.1.6.7.3.1.2 |
worpIntraCellBlockingGroupTableEntryStatusThis parameter is used to enable, disable the IntraCell Blocking Group Table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.6.7.3.1.3 |
securityGateway OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.1.6.8 |
securityGatewayStatusThis parameter is used to enable or disable security gateway feature.rw Enumeration .1.3.6.1.4.1.841.1.1.1.6.8.1 |
securityGatewayMacAddressThis parameter represents the security Gateway MAC Address to which all frames will be forwarded by the device.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.6.8.2 |
stpFrameForwardStatusSTP Frame forward status will block/allow the IEEE 802.1D and 802.1Q reserved MAC addresses (01:80:C2:00:00:00 to 01:80:C2:00:00:0F) Select 1 to enable this parameter and 2 to disable this parameter.rw Enumeration .1.3.6.1.4.1.841.1.1.1.6.9 |
stormThreshold OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.1.6.10 |
stormThresholdTableThis table contains information on the threshold value of the multicast and brodcast packects that can be processed for interface(s) present in the device . SEQUENCE OF StormThresholdTableEntry .1.3.6.1.4.1.841.1.1.1.6.10.1 |
stormThresholdTableEntryThis parameter represents the entry in the storm threshold table. StormThresholdTableEntry .1.3.6.1.4.1.841.1.1.1.6.10.1.1 |
stormThresholdTableIndexThis parameter is used as index for the storm Threshold Table.ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.6.10.1.1.1 |
stormFilterInterfaceThis parameter is used to configure the interface.The filter can be enabled either for Ethernet or Wireless. 1 for Ethernet 2 for Wirelessro Enumeration .1.3.6.1.4.1.841.1.1.1.6.10.1.1.2 |
stormMulticastThresholdThis parameter is used to provide the threshold value of the multicast packets to be processed for the interface. If threshold value for multicast packets is set to '0', no filtering will take place (filtering will be disabled).Excess packets will be dropped if packets are more than threshold value.To disable MultiCast packets filtering for this interface this variable should be set to '0'(zero).rw INTEGER .1.3.6.1.4.1.841.1.1.1.6.10.1.1.3 |
stormBroadcastThresholdThis parameter is used to provide the threshold value of the broadcast packets to be processed for interface.If threshold value for broadcast packets is set to '0', no filtering will take place (filtering will be disabled). Excess packets will be dropped if packets are more than threshold value.To disable Broadcast wireless packets filtering,this variable should be set to '0' (Zero).rw INTEGER .1.3.6.1.4.1.841.1.1.1.6.10.1.1.4 |
dhcp OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.1.7 |
dhcpServer OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.1.7.1 |
dhcpServerStatusThis parameter indicates if the DHCP server/relay is enabled or disabled in the device.rw Enumeration .1.3.6.1.4.1.841.1.1.1.7.1.1 |
dhcpMaxLeaseTimeThis parameter represents the maximum lease time in 100th seconds for the IP address assigned by the DHCP server to the DHCP client.rw TimeTicks .1.3.6.1.4.1.841.1.1.1.7.1.2 |
dhcpServerIfTableThis table is used to configure the DHCP server for a particular interface. SEQUENCE OF DhcpServerIfTableEntry .1.3.6.1.4.1.841.1.1.1.7.1.3 |
dhcpServerIfTableEntryThis parameter represents the entry for the dhcpServerIfTable. DhcpServerIfTableEntry .1.3.6.1.4.1.841.1.1.1.7.1.3.1 |
dhcpServerIfTableIndexThis parameter represents the index for the dhcpServerIfTable.ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.7.1.3.1.1 |
dhcpServerInterfaceTypeThis parameter shows the list of interfaces for which the DHCP can be configured.ro Enumeration .1.3.6.1.4.1.841.1.1.1.7.1.3.1.2 |
dhcpServerNetMaskThis parameter is used to configure the mask for the interface shown.rw IpAddress .1.3.6.1.4.1.841.1.1.1.7.1.3.1.3 |
dhcpServerDefaultGatewayThis parameter represents the IP Address of the gateway or router that the DHCP Server will assign to the DHCP client.rw IpAddress .1.3.6.1.4.1.841.1.1.1.7.1.3.1.4 |
dhcpServerPrimaryDNSThis parameter represents the primary DNS Server IP Address to be assinged to a DHCP Client.rw IpAddress .1.3.6.1.4.1.841.1.1.1.7.1.3.1.5 |
dhcpServerSecondaryDNSThis parameter represents the secondary DNS Server IP Address to be assinged to a DHCP Client.rw IpAddress .1.3.6.1.4.1.841.1.1.1.7.1.3.1.6 |
dhcpServerDefaultLeaseTimeThis parameter represents the default lease time, in 100th seconds, for the IP address assigned by the DHCP server to the DHCP client.rw TimeTicks .1.3.6.1.4.1.841.1.1.1.7.1.3.1.7 |
dhcpServerIfTableCommentThis parameter represents an optional comment for this table entry.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.7.1.3.1.8 |
dhcpServerIfTableEntryStatusThis parameter is used to configure the row status for the dhcpServerIfTable. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.7.1.3.1.9 |
dhcpServerIpPoolTableThis table contains the pools of IP Addresses that the DHCP server will assign to the DHCP clients. SEQUENCE OF DhcpServerIpPoolTableEntry .1.3.6.1.4.1.841.1.1.1.7.1.4 |
dhcpServerIpPoolTableEntryThis parameter represents entries in the dhcpServerIpPoolTable. DhcpServerIpPoolTableEntry .1.3.6.1.4.1.841.1.1.1.7.1.4.1 |
dhcpServerIpPoolTableIndexThis parameter is used as the index for the IP Address Pool table.ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.7.1.4.1.1 |
dhcpServerIpPoolInterfaceThis parameter shows the list of interfaces for which the DHCP server can be configured.rw Enumeration .1.3.6.1.4.1.841.1.1.1.7.1.4.1.2 |
dhcpServerIpPoolStartIpAddressThis parameter represents the start IP address for this DHCP IP Address IP Pool Table entry.rw IpAddress .1.3.6.1.4.1.841.1.1.1.7.1.4.1.3 |
dhcpServerIpPoolEndIpAddressThis parameter represents the end IP address for this DHCP IP Address IP Pool Table entry.rw IpAddress .1.3.6.1.4.1.841.1.1.1.7.1.4.1.4 |
dhcpServerIpPoolTableEntryStatusThis parameter is used to configure the row status for the dhcpServerIpPoolTable. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.7.1.4.1.5 |
dhcpRelay OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.1.7.2 |
dhcpRelayServerTableThis table contains a list of DHCP servers to which the DHCP Agent will communicate with. SEQUENCE OF DhcpRelayServerTableEntry .1.3.6.1.4.1.841.1.1.1.7.2.1 |
dhcpRelayServerTableEntryThis parameter represents and entry in the DHCP Server table. DhcpRelayServerTableEntry .1.3.6.1.4.1.841.1.1.1.7.2.1.1 |
dhcpRelayServerTableIndexThis parameter is used as the index to this dhcpRelayServerTable.ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.7.2.1.1.1 |
dhcpRelayServerIpAddressThis parameter represents the IP address of the DHCP server that shall receive DHCP requests from the device.rw IpAddress .1.3.6.1.4.1.841.1.1.1.7.2.1.1.2 |
dhcpRelayServerTableEntryStatusThis parameter is used to configure the row status for the dhcpRelayServerTable. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.7.2.1.1.3 |
sysConf OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.1.8 |
sysTypeTableThis table holds the information about the supported and current modes of the device. SEQUENCE OF SysTypeTableEntry .1.3.6.1.4.1.841.1.1.1.8.1 |
sysTypeTableEntryThis parameter represents the entry status for the sysTypeTable. It can hold one entry. SysTypeTableEntry .1.3.6.1.4.1.841.1.1.1.8.1.1 |
sysTypeRadioIfIndexThis parameter represents the physical interface (radio) and index for the sysType Table.ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.8.1.1.1 |
sysTypeModeThis parameter is used to configure the mode of the radio(s). Please refer the sysTypeSupportedMode object for the supported modes. The modes are represented in numbers as follows: AP (1), CLIENT (2), WDS (3), BSU (4), *Applies in TMP(tsunamiMP) mode - please refer sysFeatureProductFamily* EndPointA (4), *Applies in QB(tsunamiQuickBridge) mode - please refer sysFeatureProductFamily* SU (5) *Applies in TMP(tsunamiMP) mode - please refer sysFeatureProductFamily* EndPointB (5) *Applies in QB(tsunamiQuickBridge) mode - please refer sysFeatureProductFamily*rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.8.1.1.2 |
sysTypeActiveModeThis parameter shows the active mode of the radio(s). The configured mode will take effect after the reboot. The modes are represented in numbers as follows: AP (1), CLIENT (2), WDS (3), BSU (4), *Applies in TMP(tsunamiMP) mode - please refer sysFeatureProductFamily* EndPointA (4), *Applies in QB(tsunamiQuickBridge) mode - please refer sysFeatureProductFamily* SU (5) *Applies in TMP(tsunamiMP) mode - please refer sysFeatureProductFamily* EndPointB (5) *Applies in QB(tsunamiQuickBridge) mode - please refer sysFeatureProductFamily*ro Unsigned32 .1.3.6.1.4.1.841.1.1.1.8.1.1.3 |
sysTypeSupportedModeThis parameter displays the supported modes of operations complying with the license.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.8.1.1.4 |
sysTypeSupportedFreqDomainsThis parameter displays the supported frequency domains.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.1.8.1.1.5 |
sysTypeFreqDomainThis parameter is used to configure the frequency domain. The following list shows in detail: - United States All: 5.3 + 5.4 with DFS and 5.8 without DFS - United States Adhoc: 5.8 without DFS only - United States 2.4 GHz - World All - World 4.9 GHz (4.940 - 4.990 GHz) - World 2.4 GHz (2.400 - 2.472 GHz) - World 2.3 GHz - World 2.5 GHz - Canada 5 GHz (5.250 - 5.350 & 5.470 - 5.600 & 5.650 - 5.725 GHz all bands with DFS) - Europe 5.8 GHz (5.725 - 5.850 GHz with DFS) - Europe 5.4 GHz (5.470 - 5.600 & 5.650 - 5.725 GHz both with DFS) - Europe 2.4 GHz (2.400 - 2.4825 GHz) - Russia 5 GHz (5.150 - 6.080 GHz without DFS) - Taiwan 5 GHz (5.500 - 5.700 with DFS & 5.725 - 5.825 GHz without DFS) - United State 5 GHz (5.250 - 5.350 & 5.470 - 5.725 GHz with DFS & 5.725 - 5.850 GHz without DFS) - Canada 5.8 GHz. - Russia Frequency Convertor. - Japan 2.4 GHz (2412 - 2472 MHz) - Japan 4.9 GHz (4920 - 4980 MHz and 5040 - 5080 MHz). - UK 5.8 GHz (5725 - 5795 MHz and 5825 - 5850 MHz) - World 5.9GHz - United States 5.3 and 5.8 GHz - India 5.8GHz.rw Enumeration .1.3.6.1.4.1.841.1.1.1.8.1.1.6 |
sysTypeActiveFreqDomainThis parameter shows the active frequency domain. The following list shows in detail: - United States All: 5.3 + 5.4 with DFS and 5.8 without DFS - United States Adhoc: 5.8 without DFS only - United States 2.4 GHz - World All - World 4.9 GHz (4.940 - 4.990 GHz) - World 2.4 GHz (2.400 - 2.472 GHz) - World 2.3 GHz - World 2.5 GHz - Canada 5 GHz (5.250 - 5.350 & 5.470 - 5.600 & 5.650 - 5.725 GHz all bands with DFS) - Europe 5.8 GHz (5.725 - 5.850 GHz with DFS) - Europe 5.4 GHz (5.470 - 5.600 & 5.650 - 5.725 GHz both with DFS) - Europe 2.4 GHz (2.400 - 2.4825 GHz) - Russia 5 GHz (5.150 - 6.080 GHz without DFS) - Taiwan 5 GHz (5.500 - 5.700 with DFS & 5.725 - 5.825 GHz without DFS) - United State 5 GHz (5.250 - 5.350 & 5.470 - 5.725 GHz with DFS & 5.725 - 5.850 GHz without DFS) - Canada 5.8 GHz. - Russia Frequency Convertor - Japan 2.4 GHz (2412 - 2472 MHz) - Japan 4.9 GHz (4920 - 4980 MHz and 5040 - 5080 MHz). - UK 5.8 GHz (5725 - 5795 MHz and 5825 - 5850 MHz) - World 5.9GHz - United States 5.3 and 5.8 GHz - India 5.8GHz.ro Enumeration .1.3.6.1.4.1.841.1.1.1.8.1.1.7 |
sysNetworkModeThis parameter is used to configure the network mode of the device.rw Enumeration .1.3.6.1.4.1.841.1.1.1.8.2 |
sysActiveNetworkModeThis parameter is shows the network mode of the device. This can be configured in the sysNetworkMode.ro Enumeration .1.3.6.1.4.1.841.1.1.1.8.3 |
sysConfCountryCodeThis attribute identifies the country in which the station is operating to set the frequency band. The first two octets of this string is the two character country code as described in document ISO/IEC 3166-1. This object is not supported for the current products, please refer sysTypeFreqDomain for configuring the Frequency band. Below is the list of mapping of country codes to country names. A5 - ALL5GHz AL - ALBANIA DZ - ALGERIA AR - ARGENTINA AM - ARMENIA AU - AUSTRALIA AT - AUSTRIA AZ - AZERBAIJAN BH - BAHRAIN BY - BELARUS BE - BELGIUM BZ - BELIZE BO - BOLIVIA BR - BRAZIL BN - BRUNEI DARUSSALAM BG - BULGARIA CA - CANADA CL - CHILE CN - CHINA CO - COLOMBIA CR - COSTA RICA HR - CROATIA CY - CYPRUS CZ - CZECH REPUBLIC DK - DENMARK DO - DOMINICAN REPUBLIC EC - ECUADOR EG - EGYPT EE - ESTONIA EU - EUROPEAN UNION FI - FINLAND FR - FRANCE GE - GEORGIA DE - GERMANY GR - GREECE GT - GUATEMALA HK - HONG KONG HU - HUNGARY IS - ICELAND IN - INDIA ID - INDONESIA IR - IRAN IE - IRELAND I1 - IRELAND - 5.8GHz IL - ISRAEL IT - ITALY JP - JAPAN J2 - JAPAN2 JM - JAMAICA JO - JORDAN KZ - KAZAKHSTAN KP - NORTH KOREA KR - KOREA REPUBLIC K2 - KOREA REPUBLIC2 KW - KUWAIT LV - LATVIA LB - LEBANON LI - LIECHTENSTEIN LT - LITHUANIA LU - LUXEMBOURG MO - MACAU MK - MACEDONIA MT - MALTA MY - MALAYSIA MX - MEXICO MC - MONACO MA - MOROCCO NL - NETHERLANDS NZ - NEW ZEALAND NO - NORWAY OM - OMAN PK - PAKISTAN PA - PANAMA PE - PERU PH - PHILIPPINES PL - POLAND PT - PORTUGAL PR - PUERTO RICO QA - QATAR RO - ROMANIA RU - RUSSIA SA - SAUDI ARABIA CS - SERBIA & MONTENEGRO SG - SINGAPORE SK - SLOVAK REPUBLIC SI - SLOVENIA ZA - SOUTH AFRICA ES - SPAIN SE - SWEDEN CH - SWITZERLAND SY - SYRIA TW - TAIWAN TH - THAILAND TR - TURKEY UA - UKRAINE AE - UNITED ARAB EMIRATES GB - UNITED KINGDOM G1 - UNITED KINGDOM - 5.8GHz US - UNITED STATES UW - UNITED STATES - World U1 - UNITED STATES - DFS UY - URUGUAY VE - VENEZUELA VN - VIETNAMrw DisplayString .1.3.6.1.4.1.841.1.1.1.8.4 |
igmp OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.1.10 |
igmpSnoopingGlobalStatusThis parameter is used to enable/disable the IGMP snooping. Only passive snooping is supported. This feature is supported only in bridge mode.rw Enumeration .1.3.6.1.4.1.841.1.1.1.10.1 |
igmpMembershipAgingTimerThis parameter represents the time after which the IGMP multicast group age-outs/elapses.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.10.2 |
igmpRouterPortAgingTimerThis parameter represents the time after which the IGMP router port age-outs/elapses.rw Unsigned32 .1.3.6.1.4.1.841.1.1.1.10.3 |
igmpForcedFloodIf this paramter is set with Yes, all unregistered multicast traffic and membership reports will be flooded to all ports.rw Enumeration .1.3.6.1.4.1.841.1.1.1.10.4 |
deviceMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.2 |
sys OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.2.1 |
sysCountryCodeThis attribute identifies the country in which the station is operating. The first two octets of this string is the two character country code as described in document ISO/IEC 3166-1. Below is the list of mapping of country codes to country names. This object is deprecated and please use sysConfCountryCode to set the country code. AL - ALBANIA DZ - ALGERIA AR - ARGENTINA AM - ARMENIA AU - AUSTRALIA AT - AUSTRIA AZ - AZERBAIJAN BH - BAHRAIN BY - BELARUS BE - BELGIUM BZ - BELIZE BO - BOLIVIA BR - BRAZIL BN - BRUNEI DARUSSALAM BG - BULGARIA CA - CANADA CL - CHILE CN - CHINA CO - COLOMBIA CR - COSTA RICA HR - CROATIA CY - CYPRUS CZ - CZECH REPUBLIC DK - DENMARK DO - DOMINICAN REPUBLIC EC - ECUADOR EG - EGYPT EE - ESTONIA EU - EUROPEAN UNION FI - FINLAND FR - FRANCE GE - GEORGIA DE - GERMANY GR - GREECE GT - GUATEMALA HK - HONG KONG HU - HUNGARY IS - ICELAND IN - INDIA ID - INDONESIA IR - IRAN IE - IRELAND I1 - IRELAND - 5.8GHz IL - ISRAEL IT - ITALY JP - JAPAN J2 - JAPAN2 JM - JAMAICA JO - JORDAN KZ - KAZAKHSTAN KP - NORTH KOREA KR - KOREA REPUBLIC K2 - KOREA REPUBLIC2 KW - KUWAIT LV - LATVIA LB - LEBANON LI - LIECHTENSTEIN LT - LITHUANIA LU - LUXEMBOURG MO - MACAU MK - MACEDONIA MT - MALTA MY - MALAYSIA MX - MEXICO MC - MONACO MA - MOROCCO NL - NETHERLANDS NZ - NEW ZEALAND NO - NORWAY OM - OMAN PK - PAKISTAN PA - PANAMA PE - PERU PH - PHILIPPINES PL - POLAND PT - PORTUGAL PR - PUERTO RICO QA - QATAR RO - ROMANIA RU - RUSSIA SA - SAUDI ARABIA CS - SERBIA & MONTENEGRO SG - SINGAPORE SK - SLOVAK REPUBLIC SI - SLOVENIA ZA - SOUTH AFRICA ES - SPAIN SE - SWEDEN CH - SWITZERLAND SY - SYRIA TW - TAIWAN TH - THAILAND TR - TURKEY UA - UKRAINE AE - UNITED ARAB EMIRATES GB - UNITED KINGDOM G1 - UNITED KINGDOM - 5.8GHz US - UNITED STATES UW - UNITED STATES - World U1 - UNITED STATES - DFS UY - URUGUAY VE - VENEZUELA VN - VIETNAMrwdeprecated DisplayString .1.3.6.1.4.1.841.1.1.2.1.1 |
sysInvMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.2.1.2 |
sysInvMgmtComponentTableThis table holds the system's inventory management component features. SEQUENCE OF SysInvMgmtComponentTableEntry .1.3.6.1.4.1.841.1.1.2.1.2.1 |
sysInvMgmtComponentTableEntryThis parameter represents the entry for the sysInvmgmtComponentTable SysInvMgmtComponentTableEntry .1.3.6.1.4.1.841.1.1.2.1.2.1.1 |
sysInvMgmtCompTableIndexThis parameter represents the index for sysInvMgmtCompTable.ro Unsigned32 .1.3.6.1.4.1.841.1.1.2.1.2.1.1.1 |
sysInvMgmtCompSerialNumberThis parameter identifies the system component serial numberro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.2.1.2.1.1.2 |
sysInvMgmtCompNameThis parameter identifies the system component name.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.2.1.2.1.1.3 |
sysInvMgmtCompIdThis parameter shows the identifier for the component.ro Unsigned32 .1.3.6.1.4.1.841.1.1.2.1.2.1.1.4 |
sysInvMgmtCompVariantThis parameter identifies the system component variant number.ro Unsigned32 .1.3.6.1.4.1.841.1.1.2.1.2.1.1.5 |
sysInvMgmtCompReleaseVersionThis parameter identifies the system component release version number.ro Unsigned32 .1.3.6.1.4.1.841.1.1.2.1.2.1.1.6 |
sysInvMgmtCompMajorVersionThis parameter identifies the system component major version number.ro Unsigned32 .1.3.6.1.4.1.841.1.1.2.1.2.1.1.7 |
sysInvMgmtCompMinorVersionThis parameters identifies the system component minor version number.ro Unsigned32 .1.3.6.1.4.1.841.1.1.2.1.2.1.1.8 |
sysInvMgmtSecurityIDThis parameter represents the system's Security ID.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.2.1.2.2 |
sysInvMgmtDaughterCardAvailabilityThis parameter shows the availability of the daughter card.ro Enumeration .1.3.6.1.4.1.841.1.1.2.1.2.3 |
sysFeature OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.2.1.3 |
sysFeatureCtrlIDThis parameter is used to represent the control ID for the system feature.ro Unsigned32 .1.3.6.1.4.1.841.1.1.2.1.3.1 |
sysFeatureNumRadiosThis parameter shows the number of radios supported. This is based on the license file.ro Unsigned32 .1.3.6.1.4.1.841.1.1.2.1.3.2 |
sysFeatureFreqBandThis parameter shows the supported frequency bands. This is based on the license file.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.2.1.3.3 |
sysFeatureOutBandwidthThis parameter represents the outward bandwidth in multiples of 1Mbps. This is based on the license filero Unsigned32 .1.3.6.1.4.1.841.1.1.2.1.3.4 |
sysFeatureInBandwidthThis parameter represents the inward bandwidth in multiples of 1Mbps. This is based on the license file.ro Unsigned32 .1.3.6.1.4.1.841.1.1.2.1.3.5 |
sysFeatureOpModeThis parameter represents the current operational mode of the device. This is based on the license file.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.2.1.3.6 |
sysLicFeatureTableThis table contains a list of features that the current image supports and indicates if this feature is licensed or not. Each row represents a supported feature. Supported indicates if the current image supports the image while licensed indicates that a license is available to use this feature. Based on the license information in this table, some MIB groups/subgroups/tables are enabled or disabled. SEQUENCE OF SysLicFeatureTableEntry .1.3.6.1.4.1.841.1.1.2.1.3.7 |
sysLicFeatureTableEntryThis table parameter represents the entry for the sysLicFeatureTable. This table can hold a maximum of 50 entries. SysLicFeatureTableEntry .1.3.6.1.4.1.841.1.1.2.1.3.7.1 |
sysLicFeatureTableIndexThis parameter represents the index for the sysLicFeatureTable.ro Unsigned32 .1.3.6.1.4.1.841.1.1.2.1.3.7.1.1 |
sysLicFeatureTypeThis parameter represents the feature type and shows the code of the feature.ro Unsigned32 .1.3.6.1.4.1.841.1.1.2.1.3.7.1.2 |
sysLicFeatureValueThis parameter represents feature value i.e., enabled or disabled.ro Unsigned32 .1.3.6.1.4.1.841.1.1.2.1.3.7.1.3 |
sysFeatureCumulativeBandwidthThis parameter represents the cumulative bandwidth of the device. This is based on the license file.ro Unsigned32 .1.3.6.1.4.1.841.1.1.2.1.3.8 |
sysFeatureNumEtherIfThis parameter represents the number of ethernet interfaces supported. This is based on the license file.ro Unsigned32 .1.3.6.1.4.1.841.1.1.2.1.3.9 |
sysFeatureBitmapThis parameter represents the bit map for the features enabled/disabled. The value for this parameter is interpreted as a bitfield and the respective modules are shown below: BRIDGE_MODE_ONLY = 0, WORP = 1, Intra Cell Blocking = 2, Intra BSS Blocking = 3, VLAN = 4, STATIC_ROUTING = 5, NAT = 6, FILTERING = 7. This is based on the license file.ro Unsigned32 .1.3.6.1.4.1.841.1.1.2.1.3.10 |
sysFeatureNumOfSatellitesAllowedThis parameter represents the max number of satellites supported. This is based on the license file.ro Unsigned32 .1.3.6.1.4.1.841.1.1.2.1.3.11 |
sysFeatureProductFamilyThis parameter represents the product family. This is based on the license file.ro Enumeration .1.3.6.1.4.1.841.1.1.2.1.3.12 |
sysFeatureProductClassThis parameter represents the product class. This is based on the license file.ro Enumeration .1.3.6.1.4.1.841.1.1.2.1.3.13 |
sysLicRadioInfoTableThis table holds the license file parameters for the radio(s). SEQUENCE OF SysLicRadioInfoTableEntry .1.3.6.1.4.1.841.1.1.2.1.3.14 |
sysLicRadioInfoTableEntryThis table parameter represents the entry for the sysLicRadioInfoTable. SysLicRadioInfoTableEntry .1.3.6.1.4.1.841.1.1.2.1.3.14.1 |
sysLicRadioInfoTableIndexThis parameter represents the index for the sysLicRadioInfoTable.ro Unsigned32 .1.3.6.1.4.1.841.1.1.2.1.3.14.1.1 |
sysLicRadioCompIDThis parameter represents the component ID for the radio(s).ro Unsigned32 .1.3.6.1.4.1.841.1.1.2.1.3.14.1.2 |
sysLicRadiovariantIDThis parameter represents the variant ID for the radio(s).ro Unsigned32 .1.3.6.1.4.1.841.1.1.2.1.3.14.1.3 |
sysLicRadioAntennaTypeThis parameter represents the Antenna type supported for the radio(s).ro Enumeration .1.3.6.1.4.1.841.1.1.2.1.3.14.1.4 |
sysLicRadioAntennaMimoTypeThis parameter represents the Antenna MIMO type for the radio(s).ro Enumeration .1.3.6.1.4.1.841.1.1.2.1.3.14.1.5 |
sysMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.2.1.4 |
sysMgmtCfgChangeCntThis parameter represents the number of successful commits that has taken place since the system was rebooted last.ro Counter32 .1.3.6.1.4.1.841.1.1.2.1.4.1 |
sysMgmtCfgCommitThis parameter is used to apply the changed configurations to the device. Always this should be SET with value '1'. The values available on GET or the read values are defined as follows: 200 : Commit Successful 201 : Commit Successful and reboot the device. Please check the object sysMgmtCfgErrorMsg for Commit status and other information on errors. P.S: Usual commit operation needs atleast 3 seconds and changes in wireless parameters needs upto 60 seconds time interval before sending the response.rw Unsigned32 .1.3.6.1.4.1.841.1.1.2.1.4.2 |
sysMgmtCfgRestoreThis parameter is used to restore the device to last working configurationrw Enumeration .1.3.6.1.4.1.841.1.1.2.1.4.3 |
sysMgmtCfgErrorMsgThis parameter displays the latest error message occured in configuration.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.2.1.4.4 |
sysMgmtRebootThis parameter is used to reboot device. Select 1 to reboot.rw Enumeration .1.3.6.1.4.1.841.1.1.2.1.4.5 |
sysMgmtFactoryResetThis parameter is used to reset the device to factory settings.rw Enumeration .1.3.6.1.4.1.841.1.1.2.1.4.6 |
sysMgmtLoadTextConfigThis parameter is used to load the configurations from the Text Based Configuration File.rw Enumeration .1.3.6.1.4.1.841.1.1.2.1.4.7 |
sysInfo OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.2.1.5 |
sysContactEmailThis parameter is used to identify the email address of the contact person for a device. The length of the email address should be between 6 to 32rw DisplayString .1.3.6.1.4.1.841.1.1.2.1.5.1 |
sysContactPhoneNumberThis parameter is used to identify the phone number of the contact person for a device.rw DisplayString .1.3.6.1.4.1.841.1.1.2.1.5.2 |
sysLocationNameThis parameter is used to store the location of the system.rw DisplayString .1.3.6.1.4.1.841.1.1.2.1.5.3 |
sysGPSLongitudeThis parameter is used to represent Longitude.rw DisplayString .1.3.6.1.4.1.841.1.1.2.1.5.4 |
sysGPSLatitudeThis parameter is used to represent Latitude.rw DisplayString .1.3.6.1.4.1.841.1.1.2.1.5.5 |
sysGPSAltitudeThis parameter is used to display the elevation of an access point from a known level.rw DisplayString .1.3.6.1.4.1.841.1.1.2.1.5.6 |
productDescrA textual description of the entity. This value should includes the full name and version identification of the system's hardware type, software operating-system, and networking software.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.2.1.5.7 |
systemNameAn administratively-assigned name for this managed node. By convention, this is the node's fully-qualified domain name.rw DisplayString .1.3.6.1.4.1.841.1.1.2.1.5.8 |
mgmtSnmp OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.2.2 |
mgmtSnmpReadPasswordThis parameter is used for the SNMP password and represents the read-only community name used in the SNMP protocol.It is used for reading objects from the SNMP agent. The password should be treated as write-only and would be returned as asterisks. User is not allowed to set since it is same as mgmtSnmpReadWritePasswordrw Password .1.3.6.1.4.1.841.1.1.2.2.1 |
mgmtSnmpReadWritePasswordThis parameter is used to represent the read-write community name used in the SNMP protocol. This parameter is used for reading and writing objects to the SNMP agent. This parameter should be treated as write-only and returned as asterisks.rw Password .1.3.6.1.4.1.841.1.1.2.2.2 |
mgmtSnmpAccessTableThis table holds the objects of the mgmtSnmpAccessTable. SEQUENCE OF MgmtSnmpAccessTableEntry .1.3.6.1.4.1.841.1.1.2.2.3 |
mgmtSnmpAccessTableEntryThis parameter represents the entry for the mgmtSnmpAccessTable. MgmtSnmpAccessTableEntry .1.3.6.1.4.1.841.1.1.2.2.3.1 |
mgmtSnmpAccessTableIndexThis parameter represents the index for the mgmtSnmpAccessTable and this is not-accessible. Unsigned32 .1.3.6.1.4.1.841.1.1.2.2.3.1.1 |
mgmtSnmpTrapHostTableThis table contains the destination IP address and community password for the trap delivery. SEQUENCE OF MgmtSnmpTrapHostTableEntry .1.3.6.1.4.1.841.1.1.2.2.4 |
mgmtSnmpTrapHostTableEntryThis parameter represents the entry for the mgmtSnmpTrapHostTable. MgmtSnmpTrapHostTableEntry .1.3.6.1.4.1.841.1.1.2.2.4.1 |
mgmtSnmpTrapHostTableIndexThis parameter represents the index for SNMP Trap Host table. This table supports upto 5 rows.ro Unsigned32 .1.3.6.1.4.1.841.1.1.2.2.4.1.1 |
mgmtSnmpTrapHostTableIPAddressThis parameter is used to represent the IP address of the management station that will receive SNMP traps from the device.rw IpAddress .1.3.6.1.4.1.841.1.1.2.2.4.1.2 |
mgmtSnmpTrapHostTablePasswordThis parameter is used to represent the password that is sent with the SNMP trap messages to allow the host to accept or reject the traps. The trap host will accept SNMP traps if the sent password matches the host's password. This parameter returns asterisks on get. This is not allowed to set because it is same as mgmtSnmpReadWritePassword.rw Password .1.3.6.1.4.1.841.1.1.2.2.4.1.3 |
mgmtSnmpTrapHostTableCommentThis parameter represents the comment for the row in the SNMP Trap Host Table.rw DisplayString .1.3.6.1.4.1.841.1.1.2.2.4.1.4 |
mgmtSnmpTrapHostTableEntryStatusThis parameter is used to configure the row status for the SNMP Trap Host table. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.2.2.4.1.5 |
mgmtSnmpVersionThis parameter is used to configure the SNMP Version. The version v2c provides the security by means of community passwords and the version v3 provides highest security with authentication and encryption.rw Enumeration .1.3.6.1.4.1.841.1.1.2.2.5 |
mgmtSnmpV3SecurityLevelThis parameter allows to select the security level for SNMPV3. The level noAuthNoPriv is not supported.rw Enumeration .1.3.6.1.4.1.841.1.1.2.2.6 |
mgmtSnmpV3AuthProtocolThis parameter allows to configure the authentication protocol in SNMPV3. Select 2 for MD5 and 3 for SHA.rw Enumeration .1.3.6.1.4.1.841.1.1.2.2.7 |
mgmtSnmpV3AuthPasswordThis parameter allows to configure the authentication password for the authentication protocol.rw V3Password .1.3.6.1.4.1.841.1.1.2.2.8 |
mgmtSnmpV3PrivProtocolThis parameter allows to configure the privacy (encryption) protocol in SNMPV3. Select 2 for DES and 3 for AES-128.rw Enumeration .1.3.6.1.4.1.841.1.1.2.2.9 |
mgmtSnmpV3PrivPasswordThis parameter allows to configure the privacy (encryption) password for the privacy protocol.rw V3Password .1.3.6.1.4.1.841.1.1.2.2.10 |
http OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.2.3 |
httpPasswordThis parameter represents the system access password for the HTTP interface to manage the device via a web browser.This parameter would return the value in asterisks.rw Password .1.3.6.1.4.1.841.1.1.2.3.1 |
httpPortThis parameter is used to configure the port on which HTTP is accessed.rw Unsigned32 .1.3.6.1.4.1.841.1.1.2.3.2 |
telnet OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.2.4 |
telnetPasswordThis parameter represents the system access password for the Telnet interface. This parameter would return the value in asterisks.rw Password .1.3.6.1.4.1.841.1.1.2.4.1 |
telnetPortThis parameter is used to configure the port on which the Telnet is accessed.rw Unsigned32 .1.3.6.1.4.1.841.1.1.2.4.2 |
telnetSessionsThis parameter is used to configure the number of telnet sessions. A total of 10 sessions (Telnet + SSH) are availablerw Unsigned32 .1.3.6.1.4.1.841.1.1.2.4.3 |
tftp OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.2.5 |
tftpSrvIpAddressThis parameter represents the IP address of the TFTP server.rw IpAddress .1.3.6.1.4.1.841.1.1.2.5.1 |
tftpFileNameThis parameter represents the filename that is to upload or download from the TFTP server.rw DisplayString .1.3.6.1.4.1.841.1.1.2.5.2 |
tftpFileTypeThis parameter informs the device about the type of file that is being uploaded or downloaded. Select (1) if it is config file (2) if it is an image file and (3) if it is an eventlog file. (4) if it is a templog file. (5) if it is a Text Based Config File. (6) if it is a eventlog File.rw Enumeration .1.3.6.1.4.1.841.1.1.2.5.3 |
tftpOpTypeThis parameter represents the type of TFTP operation that is to be executed. The upload functionality will transfer the specified file from the device to the TFTP server. The download functionality will transfer the specified file from the TFTP server to the device. The download and reboot functionality will download the file from the TFTP server and then reboots the device. Select (1) to upload the image, (2) to download the image and (3) to Download & Reboot the device. (4) nonerw Enumeration .1.3.6.1.4.1.841.1.1.2.5.4 |
tftpOpStatusThis parameter represents the TFTP operation status. 1 - Idle, 2 - Download in progress 3 - Download Success 4 - Download Failure 5 - Signature check in progress 6 - Signature check failed 7 - Write on flash is in progress 8 - Write on flash is failed 9 - Upload in progress 10 - Upload success 11 - Upload failedro Enumeration .1.3.6.1.4.1.841.1.1.2.5.5 |
trapControl OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.2.6 |
genericTrapThis parameter is used to provide additional information on traps. DisplayString (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.2.6.1 |
globalTrapStatusThis parameter is used to enable or disable the configuration related traps and this is not allowed to set. Enumeration .1.3.6.1.4.1.841.1.1.2.6.2 |
mgmtAccessControl OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.2.7 |
allIntAccessControlThis parameter allows to control all management interface accesses. Select 1 - enable and 2 - disable Alert: Disabling this parameter disables all interfaces. Only serial console can be accessed for device management.rw Enumeration .1.3.6.1.4.1.841.1.1.2.7.1 |
httpAccessControlThis parameter allows to enable or disable the HTTP access. Select 1 - enable and 2 - disablerw Enumeration .1.3.6.1.4.1.841.1.1.2.7.2 |
httpsAccessControlThis parameter allows to enable or disable the HTTPS access. Select 1 - enable and 2 - disablerw Enumeration .1.3.6.1.4.1.841.1.1.2.7.3 |
snmpAccessControlThis parameter allows to enable or disable the SNMP access. Select 1 - enable and 2 - disablerw Enumeration .1.3.6.1.4.1.841.1.1.2.7.4 |
telnetAccessControlThis parameter allows to enable or disable the TELNET access. Select 1 - enable and 2 - disablerw Enumeration .1.3.6.1.4.1.841.1.1.2.7.5 |
sshAccessControlThis parameter allows to enable or disable the SSH access. Select 1 - enable and 2 - disablerw Enumeration .1.3.6.1.4.1.841.1.1.2.7.6 |
mgmtAccessTableStatusThis parameter allows to enable or disable the Management Access Table. Enabling this parameter allows the traffic from only the IP address specified in the Management Access Table. Select 1 - enable and 2 - disablerw Enumeration .1.3.6.1.4.1.841.1.1.2.7.7 |
mgmtAccessTableThis table provides the facility to allow the traffic from a particular machine identified by the IP address. SEQUENCE OF MgmtAccessTableEntry .1.3.6.1.4.1.841.1.1.2.7.8 |
mgmtAccessTableEntryThis parameter represents the entry for the Management Access Table. It can hold a maximum of 5 entries. MgmtAccessTableEntry .1.3.6.1.4.1.841.1.1.2.7.8.1 |
mgmtAccessTableIndexThis parameter represents the index of the Management Access Table.ro Unsigned32 .1.3.6.1.4.1.841.1.1.2.7.8.1.1 |
mgmtAccessTableIpAddressThis parameter holds the IP address of the machine to which traffic need to be allowed.rw IpAddress .1.3.6.1.4.1.841.1.1.2.7.8.1.2 |
mgmtAccessTableEntryStatusThis parameter represents the entry status for the Management Access Table. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.2.7.8.1.3 |
ssh OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.2.8 |
sshPortThis parameter is used to configure the port on which SSH is accessed.rw Unsigned32 .1.3.6.1.4.1.841.1.1.2.8.1 |
sshSessionsThis parameter is used to set the number of concurrent SSH sessions.rw Unsigned32 .1.3.6.1.4.1.841.1.1.2.8.2 |
deviceMon OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.3 |
syslog OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.3.1 |
syslogStatusThis parameter is used to configure the status for the sysLog. Select 1 to enable the Syslog status and 2 to disable the syslog status.rw Enumeration .1.3.6.1.4.1.841.1.1.3.1.1 |
syslogPriorityThis parameter is used to configure the priority for the syslog. Select 1 for emergency, 2 for alert, 3 for critical, 4 for error, 5 for warning, 6 for notice, 7 for info and 8 for debug.rw Enumeration .1.3.6.1.4.1.841.1.1.3.1.2 |
syslogResetThis parameter is used to reset or clear the syslog. Select 1 - to reset or clear 2 - none.rw Enumeration .1.3.6.1.4.1.841.1.1.3.1.3 |
syslogHostTableThis table contains the syslog configurations. SEQUENCE OF SyslogHostTableEntry .1.3.6.1.4.1.841.1.1.3.1.4 |
syslogHostTableEntryThis parameter represents the entry for the syslogHostTable. SyslogHostTableEntry .1.3.6.1.4.1.841.1.1.3.1.4.1 |
syslogHostTableIndexThis parameter is used to index the syslogHostTable.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.1.4.1.1 |
syslogHostIpAddressThis parameter is used to represent the IP address for which syslog messages to be sent.rw IpAddress .1.3.6.1.4.1.841.1.1.3.1.4.1.2 |
syslogHostPortThis parameter is used to represents the host port number for which the syslog messages are sent.rw Unsigned32 .1.3.6.1.4.1.841.1.1.3.1.4.1.3 |
syslogHostCommentThis parameter displays the comment for the host port of the syslog table.rw DisplayString .1.3.6.1.4.1.841.1.1.3.1.4.1.4 |
syslogHostTableEntryStatusThis parameter is used to configue the status of the Syslog host entry table. A maximum of 5 entries can be added to this table. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.3.1.4.1.5 |
eventlog OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.3.2 |
eventLogPriorityThis parameter is used to configure the priority for the event log table. Select 1 for Emergency, 2 for alert, 3 for critical, 4 for error, 5 for warning, 6 for notice, 7 for info and 8 for debug.rw Enumeration .1.3.6.1.4.1.841.1.1.3.2.1 |
eventLogResetThis parameter is used to reset/clear the event log table. When this parameter is set, then all enteries in the event log table are deleted/cleared. Select (1) to reset the table.rw Enumeration .1.3.6.1.4.1.841.1.1.3.2.2 |
sntp OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.3.3 |
sntpStatusThis parameter is used to enable or disable the SNTP functionality. Select 1 to enable SNTP and 2 to Disable the SNTP functionality.rw Enumeration .1.3.6.1.4.1.841.1.1.3.3.1 |
sntpPrimaryServerNameThis parameter is used for the primary SNTP server name.rw DisplayString .1.3.6.1.4.1.841.1.1.3.3.2 |
sntpSecondaryServerNameThis parameter is used for the secondary SNTP server name.rw DisplayString .1.3.6.1.4.1.841.1.1.3.3.3 |
sntpTimeZoneThis parameter is used to specify the appropriate time zone. dateline(1), samoa(2), hawaii(3), alaska(4), pacific-us(5), mountain-us(6), arizona(7), central-us(8), mexico-city(9), eastern-us(10), indiana(11), atlantic-canada(12), santiago(13), ewfoundland(14), brasilia(15), buenos-aires(16), mid-atlantic(17), azores(18), london(19), western-europe(20), eastern-europe(21), cairo(22), russia-iraq(23), iran(24), arabian(25), afghanistan(26), pakistan(27), india(28), bangladesh(29), burma(30), bangkok(31), australia-wt(32), hong-kong(33), beijing(34), japan-korea(35), australia-ct(36), australia-et(37), central-pacific(38), new-zealand(39), tonga(40), western-samoa(41)rw Enumeration .1.3.6.1.4.1.841.1.1.3.3.4 |
sntpDayLightSavingTimeThis parameter is used to indicate the number of hours to adjust for Daylight Saving Time. plus-two(1), plus-one(2), unchanged(3), minus-one(4), minus-two(5)rw Enumeration .1.3.6.1.4.1.841.1.1.3.3.5 |
sntpShowCurrentTimeThis parameter displays the current time got from the SNTP serverro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.3.3.6 |
wirelessIfMon OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.3.4 |
wirelessIfStaStats OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.3.4.1 |
wirelessIfStaStatsTableThis table contains wireless stations statistics. SEQUENCE OF WirelessIfStaStatsTableEntry .1.3.6.1.4.1.841.1.1.3.4.1.1 |
wirelessIfStaStatsTableEntryThis parameter represents the entry for wirelessIfStaStatsTable. This is indexed by interface and VAP numbers. WirelessIfStaStatsTableEntry .1.3.6.1.4.1.841.1.1.3.4.1.1.1 |
wirelessIfStaStatsTableIndexThis parameter represents the index for the wirelessIfStaStatsTable.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.1 |
wirelessIfStaStatsTableSecIndexThis parameter is user defined represents the index of the stations statistics wireless interface table. This table is limited to 255 entries.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.2 |
wirelessIfStaStatsIfNumberThis parameter represents the number of the station statistics for wireless interface table. You can configure up to 2 entries.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.3 |
wirelessIfStaStatsVAPNumberThe parameter represents the VAP that can be configured for wireless interface. You can configure up to 4.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.4 |
wirelessIfStaStatsMACAddressThis parameter represents the MAC address of the station for wireless interface for which the statistics are gathered.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.3.4.1.1.1.5 |
wirelessIfStaStatsRxMgmtFramesThis parameter represents the Management frames that are recevied..ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.6 |
wirelessIfStaStatsRxControlFramesThis parameter represnets the control frames that are recevied.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.7 |
wirelessIfStaStatsRxUnicastFramesThis parameter represents the unicast frames that are recevied.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.8 |
wirelessIfStaStatsRxMulticastFramesThis parameter represents the multicast frames that are recevied.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.9 |
wirelessIfStaStatsRxBytesThis parameter represents the number of bytes received.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.10 |
wirelessIfStaStatsRxBeaconsThis parameter represents the number of beacons received.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.11 |
wirelessIfStaStatsRxProbeRespThis parameter represents the number of probe requests recevied.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.12 |
wirelessIfStaStatsRxDupFramesThis parameter represents the duplicate frames recevied.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.13 |
wirelessIfStaStatsRxNoPrivacyThis parameter represents the no privacy information recevied.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.14 |
wirelessIfStaStatsRxWepFailThis parameter represents the failed WEP information recevied.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.15 |
wirelessIfStaStatsRxDeMicFailThis parameter represents the failed deMIC information recevied.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.16 |
wirelessIfStaStatsRxDecapFailedThis parameter represents the failed decapulation information recevied.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.17 |
wirelessIfStaStatsRxDefragFailedThis parameter represents the failed defragmentation information recevied.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.18 |
wirelessIfStaStatsRxDisassociationFramesThis parameter represents the disassociated frames that are recevied.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.19 |
wirelessIfStaStatsRxDeauthenticationFramesThis parameter represents the deauthenticated frames that are recevied.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.20 |
wirelessIfStaStatsRxDecryptFailedOnCRCThis parameter represents the decrypt information failed on CRC recevied.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.21 |
wirelessIfStaStatsRxUnauthPortThis parameter represents the unauthorized port information recevied.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.22 |
wirelessIfStaStatsRxUnencryptedThis parameter represents the unencrypted information recevied.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.23 |
wirelessIfStaStatsTxDataFramesThis parameter represents the data frames that are transmitted.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.24 |
wirelessIfStaStatsTxMgmtFramesThis parameter represents the management frames that are transmitted.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.25 |
wirelessIfStaStatsTxUnicastFramesThis parameter represents the number of unicast frames from the station that are further transmitted either by the bridge/router or by the internal host.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.26 |
wirelessIfStaStatsTxMulticastFramesThis parameter represents the number of multicast frames from the station that are further transmitted either by the bridge/router or by the internal host.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.27 |
wirelessIfStaStatsTxBytesThis parameter represents the number of bytes from the station that are further transmitted either by the bridge/router or by the internal host.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.28 |
wirelessIfStaStatsTxProbeReqThis parameter represents the number of transmitted probe request from the station either by the bridge/router or by internal host.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.29 |
wirelessIfStaStatsTxEospLostThis parameter represents the end of service period.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.30 |
wirelessIfStaStatsTxPSDiscardThis parameter displays the power save mode.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.31 |
wirelessIfStaStatsTxAssociationFramesThis parameter represents the number of associated frames transmitted.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.32 |
wirelessIfStaStatsTxAssociationFailedFramesThis parameter represents the number of the failed associated frames transmitted.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.33 |
wirelessIfStaStatsTxAuthenticationFramesThis parameter represents the number of the authentication frames transmitted.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.34 |
wirelessIfStaStatsTxAuthenticationFailedThis parameter represents the failed authentication frames.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.35 |
wirelessIfStaStatsTxDeAuthFramesThis parameter represents the deauthorized frames transmitted.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.36 |
wirelessIfStaStatsTxDeAuthCodeThis parameter represents the deauthorized code transmitted.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.37 |
wirelessIfStaStatsTxDisassociationThis parameter represents the disassociation information transmitted.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.38 |
wirelessIfStaStatsTxDisassociationCodeThis parameter representd the disassociation code transmitted.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.39 |
wirelessIfStaStatsFrequencyThis parameter represents the frequency on which the station is operating.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.40 |
wirelessIfStaStatsStateThis parameter represents the present state of the station.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.41 |
wirelessIfStaStatsRSSIThis parameter represents the RSSI (received signal strength) of the station.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.42 |
wirelessIfStaStatsTxRateThis parameter represents the transmission rate of the station.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.43 |
wirelessIfStaStatsAuthenAlgorithmThis parameter represents the authentication alogorithm used for the station.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.44 |
wirelessIfStaStatsAssociationIDThis parameter represents the association ID of the station.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.45 |
wirelessIfStaStatsVlanTagThis parameter represents the VLAN tag of the station.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.46 |
wirelessIfStaStatsAssocationTimeThis parameter represents the association time of the station.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.47 |
wirelessIfStaStatsTxPowerThis parameter represents the transmission power of the station.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.48 |
wirelessIfStaStatsInactivityTimerThis parameter represents the inactivity time of the station.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.49 |
wirelessIfStaStatsStationOperatingModeThis parameter represents the wireless operating mode of station.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.50 |
wirelessIfStaStatsHTCapabilityThis parameter represents the HT (high throughput) capability in 11n mode.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.1.1.1.51 |
wirelessIfWORPStaStatsTableThis table contains WORP stations statistics. SEQUENCE OF WirelessIfWORPStaStatsTableEntry .1.3.6.1.4.1.841.1.1.3.4.1.2 |
wirelessIfWORPStaStatsTableEntryThis parameter represents an entry in the WORP Interface Satellite Statistics Table. WirelessIfWORPStaStatsTableEntry .1.3.6.1.4.1.841.1.1.3.4.1.2.1 |
wirelessIfWORPStaStatsTableIndexThis parameter represents the table index for Station Stats Table.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.1.2.1.1 |
wirelessIfWORPStaStatsMacAddressThis parameter represents the MAC address of the satellite for which the statistics are gathered.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.3.4.1.2.1.2 |
wirelessIfWORPStaStatsSatelliteNameThis parameter identifies the name of the base unit being tested with.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.3.4.1.2.1.3 |
wirelessIfWORPStaStatsAverageLocalSignalThe current signal level calculated over all inbound packets. This variable indicates the running average of the local signal level using the algorithm (3/4*oldvalue + 1/4*newvalue).ro Integer32 (-102..-10) .1.3.6.1.4.1.841.1.1.3.4.1.2.1.4 |
wirelessIfWORPStaStatsAverageLocalNoiseThe current noise level calculated over all inbound packets. This variable indicates the running average of the local noise level using the algorithm (3/4*oldvalue + 1/4*newvalue).ro Integer32 (-102..-10) .1.3.6.1.4.1.841.1.1.3.4.1.2.1.5 |
wirelessIfWORPStaStatsAverageRemoteSignalThe current remote signal level calculated over the inbound packets send by this station. This variable indicates the running average over all registered stations of the remote signal level using the algorithm (3/4*oldvalue + 1/4*newvalue).ro Integer32 (-102..-10) .1.3.6.1.4.1.841.1.1.3.4.1.2.1.6 |
wirelessIfWORPStaStatsAverageRemoteNoiseThe current average remote noise level calculated over the inbound packets send by this station. This variable indicates the running average over all registered stations of the remote noise level using the algorithm (3/4*oldvalue + 1/4*newvalue).ro Integer32 (-102..-10) .1.3.6.1.4.1.841.1.1.3.4.1.2.1.7 |
wirelessIfWORPStaStatsRequestForServiceThe number of requests for service sent (satellite) or received (base).ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.2.1.8 |
wirelessIfWORPStaStatsPollDataThe number of polls with data sent (base) or received (satellite).ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.2.1.9 |
wirelessIfWORPStaStatsPollNoDataThe number of polls with no data sent (base) or received (satellite).ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.2.1.10 |
wirelessIfWORPStaStatsReplyDataThe number of poll replies with data sent (satellite) or received (base). This counter does not include replies with the MoreData flag set (see ReplyMoreData).ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.2.1.11 |
wirelessIfWORPStaStatsReplyNoDataThe number of poll replies with no data sent (satellite) or received (base).ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.2.1.12 |
wirelessIfWORPStaStatsSendSuccessThe number of data packets sent that were acknowledged and did not need a retransmit.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.2.1.13 |
wirelessIfWORPStaStatsSendRetriesThe number of data packets sent that needed retransmition but were finally received succesfully by the remote partner.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.2.1.14 |
wirelessIfWORPStaStatsSendFailuresThe number of data packets sent that were (finally) not received succesfully by the remote partner.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.2.1.15 |
wirelessIfWORPStaStatsReceiveSuccessThe number of data packets received that were acknowledged and did not need a retransmit of the remote partner.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.2.1.16 |
wirelessIfWORPStaStatsReceiveRetriesThe number of data packets received that needed retransmition by the remote partner but were finally received succesfully.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.2.1.17 |
wirelessIfWORPStaStatsReceiveFailuresThe number of data packets that were (finally) not received succesfully.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.2.1.18 |
wirelessIfWORPStaStatsPollNoRepliesThe number of times a poll was sent but no reply was received. This parameter only applies to the base.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.1.2.1.19 |
wirelessIfWORPStaStatsLocalTxRateThis parameter represents the Transmit Data Rate of the BSU.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.1.2.1.20 |
wirelessIfWORPStaStatsRemoteTxRateThis parameter represents the Transmit Data Rate of the SU which is registered to this SU.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.1.2.1.21 |
wirelessIfWORPStaBridgePortThis parameter represents the port number of the bridge for which this station is connected.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.1.2.1.22 |
wirelessIfWORPStaStatsAverageLocalSNRro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.1.2.1.23 |
wirelessIfWORPStaStatsAverageRemoteSNRro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.1.2.1.24 |
wirelessIfWORPStaStatsLocalMimoCtrlSig1ro Integer32 .1.3.6.1.4.1.841.1.1.3.4.1.2.1.25 |
wirelessIfWORPStaStatsLocalMimoCtrlSig2ro Integer32 .1.3.6.1.4.1.841.1.1.3.4.1.2.1.26 |
wirelessIfWORPStaStatsLocalMimoCtrlSig3ro Integer32 .1.3.6.1.4.1.841.1.1.3.4.1.2.1.27 |
wirelessIfWORPStaStatsLocalMimoNoisero Integer32 .1.3.6.1.4.1.841.1.1.3.4.1.2.1.28 |
wirelessIfWORPStaStatsLocalMimoCtrlSNR1ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.1.2.1.29 |
wirelessIfWORPStaStatsLocalMimoCtrlSNR2ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.1.2.1.30 |
wirelessIfWORPStaStatsLocalMimoCtrlSNR3ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.1.2.1.31 |
wirelessIfWORPStaStatsRemoteMimoCtrlSig1ro Integer32 .1.3.6.1.4.1.841.1.1.3.4.1.2.1.32 |
wirelessIfWORPStaStatsRemoteMimoCtrlSig2ro Integer32 .1.3.6.1.4.1.841.1.1.3.4.1.2.1.33 |
wirelessIfWORPStaStatsRemoteMimoCtrlSig3ro Integer32 .1.3.6.1.4.1.841.1.1.3.4.1.2.1.34 |
wirelessIfWORPStaStatsRemoteMimoNoisero Integer32 .1.3.6.1.4.1.841.1.1.3.4.1.2.1.35 |
wirelessIfWORPStaStatsRemoteMimoCtrlSNR1ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.1.2.1.36 |
wirelessIfWORPStaStatsRemoteMimoCtrlSNR2ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.1.2.1.37 |
wirelessIfWORPStaStatsRemoteMimoCtrlSNR3ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.1.2.1.38 |
wirelessIfWORPStaStatsLocalChainBalStatusWhen this parameter indicates the local chain balance status.ro Enumeration .1.3.6.1.4.1.841.1.1.3.4.1.2.1.39 |
wirelessIfWORPStaStatsRemoteChainBalStatusWhen this parameter indicates the remote chain balance status.ro Enumeration .1.3.6.1.4.1.841.1.1.3.4.1.2.1.40 |
wirelessIfMonNumOfStaConnectedThis parameter represents the number of stations connected.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.1.3 |
wirelessIfWORPStats OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.3.4.2 |
wirelessIfWORPStatsTableThis table is used to monitor the statistics of interfaces that run WORP. SEQUENCE OF WirelessIfWORPStatsTableEntry .1.3.6.1.4.1.841.1.1.3.4.2.1 |
wirelessIfWORPStatsTableEntryThis parameter represents an entry in the WORP Interface Statistics Table. WirelessIfWORPStatsTableEntry .1.3.6.1.4.1.841.1.1.3.4.2.1.1 |
wirelessIfWORPStatsTableIndexThis parameter represents the radio interface for which the WORP statistics are gathered and index to the wirelessIfWORPStats table.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.2.1.1.1 |
wirelessIfWORPStatsAverageLocalSignalThis parameter displays the current signal level calculated over all inbound packets.ro Integer32 (-102..-10) .1.3.6.1.4.1.841.1.1.3.4.2.1.1.2 |
wirelessIfWORPStatsAverageLocalNoiseThis parameter displays the current noise level calculated over all inbound packets.ro Integer32 (-102..-10) .1.3.6.1.4.1.841.1.1.3.4.2.1.1.3 |
wirelessIfWORPStatsAverageRemoteSignalThis parameter displays the current signal level calculated over the inbound packets received at the peer end.ro Integer32 (-102..-10) .1.3.6.1.4.1.841.1.1.3.4.2.1.1.4 |
wirelessIfWORPStatsAverageRemoteNoiseThis parameter displays the current noise level calculated over the inbound packets received at the peer end.ro Integer32 (-102..-10) .1.3.6.1.4.1.841.1.1.3.4.2.1.1.5 |
wirelessIfWORPStatsRemotePartnersThis parameter displays the number of remote partners. For a satellite, this parameter will always be zero or one.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.2.1.1.6 |
wirelessIfWORPStatsBaseStationAnnouncesThis parameter displays the number of Announcement messages sent (base) or received (satellite) on WORP interfacero Counter32 .1.3.6.1.4.1.841.1.1.3.4.2.1.1.7 |
wirelessIfWORPStatsRequestForServiceThis parameter displays the number of requests for service messages sent (satellite) or received (base).ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.2.1.1.8 |
wirelessIfWORPStatsRegistrationRequestsThis parameter displays the number of registration request messages sent (satellite) or received (base) on WORP interface.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.2.1.1.9 |
wirelessIfWORPStatsRegistrationRejectsThis parameter displays the number of registration reject messages sent (base) or received (satellite) on WORP interface.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.2.1.1.10 |
wirelessIfWORPStatsAuthenticationRequestsThis parameter displays the number of authentication request messages sent (satellite) or received (base) on WORP interface.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.2.1.1.11 |
wirelessIfWORPStatsAuthenticationConfirmsThis parameter displays the number of authentication confirm messages sent (base) or received (satellite) on WORP interface.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.2.1.1.12 |
wirelessIfWORPStatsRegistrationAttemptsThis parameter represents the number of times a Registration Attempt has been initiated.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.2.1.1.13 |
wirelessIfWORPStatsRegistrationIncompletesThis parameter represents the number of registration attempts that is not completed yet.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.2.1.1.14 |
wirelessIfWORPStatsRegistrationTimeoutsThis parameter represents the number of times the registration procedure timed out.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.2.1.1.15 |
wirelessIfWORPStatsRegistrationLastReasonThis parameter represents the reason for why the last registration was aborted or failed.ro Enumeration .1.3.6.1.4.1.841.1.1.3.4.2.1.1.16 |
wirelessIfWORPStatsPollDataThis parameter represents the number of polls with data messages sent (base) or received (satellite).ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.2.1.1.17 |
wirelessIfWORPStatsPollNoDataThis parameter represents the number of polls with no data messages sent (base) or received (satellite).ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.2.1.1.18 |
wirelessIfWORPStatsReplyDataThis parameter represents the number of poll replies with data messages sent (satellite) or received (base).ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.2.1.1.19 |
wirelessIfWORPStatsReplyMoreDataThis parameter represents the number of poll replies with more data messages sent (satellite) or received (base).ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.2.1.1.20 |
wirelessIfWORPStatsReplyNoDataThis parameter represents the number of poll replies with no data messages sent (satellite) or received (base).ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.2.1.1.21 |
wirelessIfWORPStatsPollNoRepliesThis parameter represents the number of times a poll messages were sent but no reply was received. The parameter in valid only on BSU.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.2.1.1.22 |
wirelessIfWORPStatsSendSuccessThis parameter displays the number of data messages sent and acknowledged by the peer successfully.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.2.1.1.23 |
wirelessIfWORPStatsSendRetriesThis parameter displays the number of data messages that are re-transmitted and acknowledged by the peer successfully.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.2.1.1.24 |
wirelessIfWORPStatsSendFailuresThis parameter displays the number of data messages that requires re-transmission. These frames are not acknowledged by the peer.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.2.1.1.25 |
wirelessIfWORPStatsReceiveSuccessThis parameter displays the number of data messages received and acknowledged successfully.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.2.1.1.26 |
wirelessIfWORPStatsReceiveRetriesThis parameter displays the number of successfully received re-transmitted data messages.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.2.1.1.27 |
wirelessIfWORPStatsReceiveFailuresThis parameter displays the number of data messages that were not received successfully.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.2.1.1.28 |
wirelessIfWORPStatsProvisionedUplinkCIRThis parameter provides information about the total assigned (provisioned) uplink Committed Information Rate(CIR) including all SUs.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.2.1.1.29 |
wirelessIfWORPStatsProvisionedDownlinkCIRThis parameter provides information about the total assigned (provisioned) downlink Commtied Information Rate(CIR) including all SUs.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.2.1.1.30 |
wirelessIfWORPStatsProvisionedUplinkMIRThis parameter provides information about the total assigned (provisioned) uplink Maximum Information Rate(MIR) including all SUs.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.2.1.1.31 |
wirelessIfWORPStatsProvisionedDownlinkMIRThis parameter provides information about the total assigned (provisioned) downlink Maximum Information Rate(MIR) including all SUs.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.2.1.1.32 |
wirelessIfWORPStatsActiveUplinkCIRThis parameter provides information about the total active uplink Committed Information Rate(CIR).ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.2.1.1.33 |
wirelessIfWORPStatsActiveDownlinkCIRThis parameter provides information about the total active downlink Committed Information Rate(CIR).ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.2.1.1.34 |
wirelessIfWORPStatsActiveUplinkMIRThis parameter provides information about the total active uplink Maximum Information Rate(MIR).ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.2.1.1.35 |
wirelessIfWORPStatsActiveDownlinkMIRThis parameter provides information about the total active downlink Maximum Information Rate(MIR).ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.2.1.1.36 |
wirelessIfWORPStatsCurrentUplinkBandwidthThis parameter provides information about the current bandwidth utilization on the uplink direction.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.2.1.1.37 |
wirelessIfWORPStatsCurrentDownlinkBandwidthThis parameter provides information about the current bandwidth utilization on the downlink direction.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.2.1.1.38 |
wirelessIfBlacklistInfo OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.3.4.3 |
wirelessIfBlacklistInfoTableThis table shows the blacklisted channel information. SEQUENCE OF WirelessIfBlacklistInfoTableEntry .1.3.6.1.4.1.841.1.1.3.4.3.1 |
wirelessIfBlacklistInfoTableEntryThis parameter represents an entry in the wireless interface blacklisted info table. WirelessIfBlacklistInfoTableEntry .1.3.6.1.4.1.841.1.1.3.4.3.1.1 |
wirelessIfBlacklistInfoTableIndexThis parameter is used as index to the wirelessIfBlacklistInfoTable and represents the radio number.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.3.1.1.1 |
wirelessIfBlacklistInfoTableSecIndexThis parameter is used as secondary index to the wirelessIfBlacklistInfoTable and represents the channel blacklisted.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.3.1.1.2 |
wirelessIfBlacklistedChannelNumThis parameter shows the blacklisted channel number.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.3.1.1.3 |
wirelessIfBlacklistReasonThis parameter shows the reason for the channel blacklisting.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.3.4.3.1.1.4 |
wirelessIfBlacklistTimeElapsedThis parameter shows the time since the channel is blacklisted.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.3.1.1.5 |
wirelessIfWORPLinkTest OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.3.4.4 |
wirelessIfWORPLinkTestConfTableThis table holds the WORP link test configuration parameters. SEQUENCE OF WirelessIfWORPLinkTestConfTableEntry .1.3.6.1.4.1.841.1.1.3.4.4.1 |
wirelessIfWORPLinkTestConfTableEntryThis parameter represents the WORP link test conf table entry status. WirelessIfWORPLinkTestConfTableEntry .1.3.6.1.4.1.841.1.1.3.4.4.1.1 |
wirelessIfWORPLinkTestConfTableIndexThis parameter represents the index for the WORP link test conf table.ro Unsigned32 (1) .1.3.6.1.4.1.841.1.1.3.4.4.1.1.1 |
wirelessIfWORPLinkTestExploreStatusThis parameter is used to start/stops WORP link test.rw Enumeration .1.3.6.1.4.1.841.1.1.3.4.4.1.1.2 |
wirelessIfWORPLinkTestProgressStatusThis parameter shows the progress of the WORP link test.ro Enumeration .1.3.6.1.4.1.841.1.1.3.4.4.1.1.3 |
wirelessIfWORPLinkTestIdleTimeoutThe value of this parameter determines the time (in seconds) that a link test will continue without any SNMP requests for a Link Test Table entry. When the time expires the Link Test Table is cleared.rw Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.4.1.1.4 |
wirelessIfWORPLinkTestStatsTableThis table contains the information for the stations currently associated with the access point. SEQUENCE OF WirelessIfWORPLinkTestStatsTableEntry .1.3.6.1.4.1.841.1.1.3.4.4.5 |
wirelessIfWORPLinkTestStatsTableEntryThis parameter represents the entry in the Remote Link Test table. WirelessIfWORPLinkTestStatsTableEntry .1.3.6.1.4.1.841.1.1.3.4.4.5.1 |
wirelessIfWORPLinkTestStatsTableIndexThis parameter represents a unique value for each station. The value for each station must remain constant at least from one explore to the next.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.4.5.1.1 |
wirelessIfWORPLinkTestStatsTableSecIndexThis parameter represents a unique value for each station. The value for each station must remain constant at least from one explore to the next.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.4.5.1.2 |
wirelessIfWORPLinkTestStatusWhen this parameter is set to 2 the device will initiate a link test sequence with this station.rw Enumeration .1.3.6.1.4.1.841.1.1.3.4.4.5.1.3 |
wirelessIfWORPLinkTestStationNameThis parameter identifies the name of the station whom which the link test is being performed.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.3.4.4.5.1.4 |
wirelessIfWORPLinkTestMACAddressThis parameter represents the MAC address that will be mapped to the IP Address of the station.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.3.4.4.5.1.5 |
wirelessIfWORPLinkTestWORPLinkStatusThis parameter shows the link status of WORP connectivity.ro Enumeration .1.3.6.1.4.1.841.1.1.3.4.4.5.1.6 |
wirelessIfWORPLinkTestLocalCurSignalThe current signal level (in dB) for the link test from this station. This parameter indicates the running average of the local signal level using the algorithm (3/4*oldvalue + 1/4*newvalue).ro Integer32 .1.3.6.1.4.1.841.1.1.3.4.4.5.1.7 |
wirelessIfWORPLinkTestLocalCurNoiseThe current noise level (in dB) for the link test to this station. This parameter indicates the running average of the local noise level.ro Integer32 .1.3.6.1.4.1.841.1.1.3.4.4.5.1.8 |
wirelessIfWORPLinkTestLocalCurSNRThe current signal to noise ratio for the link test to this station.ro Integer32 .1.3.6.1.4.1.841.1.1.3.4.4.5.1.9 |
wirelessIfWORPLinkTestLocalMinSignalThe minimum signal level during the link test to this station.ro Integer32 .1.3.6.1.4.1.841.1.1.3.4.4.5.1.10 |
wirelessIfWORPLinkTestLocalMinNoiseThe minimum noise level during the link test to this station.ro Integer32 .1.3.6.1.4.1.841.1.1.3.4.4.5.1.11 |
wirelessIfWORPLinkTestLocalMinSNRThe minimum signal to noise ratio during the link test to this station.ro Integer32 .1.3.6.1.4.1.841.1.1.3.4.4.5.1.12 |
wirelessIfWORPLinkTestLocalMaxSignalThe maximum signal level during the link test to this station.ro Integer32 .1.3.6.1.4.1.841.1.1.3.4.4.5.1.13 |
wirelessIfWORPLinkTestLocalMaxNoiseThe maximum noise level during the link test to this station.ro Integer32 .1.3.6.1.4.1.841.1.1.3.4.4.5.1.14 |
wirelessIfWORPLinkTestLocalMaxSNRThe maximum signal to noise ratio during the link test to this station.ro Integer32 .1.3.6.1.4.1.841.1.1.3.4.4.5.1.15 |
wirelessIfWORPLinkTestRemoteCurSignalThe current signal level for the link test to the remote station or access point.ro Integer32 .1.3.6.1.4.1.841.1.1.3.4.4.5.1.16 |
wirelessIfWORPLinkTestRemoteCurNoiseThe current noise level for the link test to the remote station or access point device.ro Integer32 .1.3.6.1.4.1.841.1.1.3.4.4.5.1.17 |
wirelessIfWORPLinkTestRemoteCurSNRThe current signal to noise ratio for the link test to the remote station or access point device.ro Integer32 .1.3.6.1.4.1.841.1.1.3.4.4.5.1.18 |
wirelessIfWORPLinkTestRemoteMinSignalThe minimum signal level during the link test to the remote station or access point device.ro Integer32 .1.3.6.1.4.1.841.1.1.3.4.4.5.1.19 |
wirelessIfWORPLinkTestRemoteMinNoiseThe minimum noise level during the link test to the remote station or access point device.ro Integer32 .1.3.6.1.4.1.841.1.1.3.4.4.5.1.20 |
wirelessIfWORPLinkTestRemoteMinSNRThe minimum signal to noise ratio during the link test to the remote station or access point device.ro Integer32 .1.3.6.1.4.1.841.1.1.3.4.4.5.1.21 |
wirelessIfWORPLinkTestRemoteMaxSignalThe maximum signal level during the link test to the remote station or access point device.ro Integer32 .1.3.6.1.4.1.841.1.1.3.4.4.5.1.22 |
wirelessIfWORPLinkTestRemoteMaxNoiseThe maximum noise level during the link test to the remote station or access point device.ro Integer32 .1.3.6.1.4.1.841.1.1.3.4.4.5.1.23 |
wirelessIfWORPLinkTestRemoteMaxSNRThe maximum signal to noise ratio during the link test to the remote station or access point device.ro Integer32 .1.3.6.1.4.1.841.1.1.3.4.4.5.1.24 |
wirelessIfStats OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.3.4.5 |
wirelessIfStatsTableThis table holds the statistics for the wireless interface(s). SEQUENCE OF WirelessIfStatsTableEntry .1.3.6.1.4.1.841.1.1.3.4.5.1 |
wirelessIfStatsTableEntryThis parameter represents the entry for the wirelessIfStatsTable. WirelessIfStatsTableEntry .1.3.6.1.4.1.841.1.1.3.4.5.1.1 |
wirelessIfStatsTableIndexThis parameter represents the index for the wirelessIfStatsTable.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.4.5.1.1.1 |
wirelessIfStatsTxPktsThis parameter shows the number of transmitted packets from the wireless interface.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.5.1.1.2 |
wirelessIfStatsTxBytesThis parameter shows the number of transmitted bytes from the wireless interface.ro Counter64 .1.3.6.1.4.1.841.1.1.3.4.5.1.1.3 |
wirelessIfStatsRxPktsThis parameter shows the number of received packets from the wireless interface.ro Counter32 .1.3.6.1.4.1.841.1.1.3.4.5.1.1.4 |
wirelessIfStatsRxBytesThis parameter shows the number of received bytes from the wireless interface.ro Counter64 .1.3.6.1.4.1.841.1.1.3.4.5.1.1.5 |
wirelessIfStatsRxDecryptErrorsThis parameter shows the number of packets received with decryption errors on the wireless interface.ro Counter64 .1.3.6.1.4.1.841.1.1.3.4.5.1.1.6 |
wirelessIfStatsRxCRCErrorsThis parameter shows the number of packets received with CRC errors on the wireless interfacero Counter64 .1.3.6.1.4.1.841.1.1.3.4.5.1.1.7 |
wirelessIfStatsChain0CtlRSSIThis parameter shows the control RSSI for the chain/antenna 0.ro Integer32 .1.3.6.1.4.1.841.1.1.3.4.5.1.1.8 |
wirelessIfStatsChain1CtlRSSIThis parameter shows the control RSSI for the chain/antenna 1.ro Integer32 .1.3.6.1.4.1.841.1.1.3.4.5.1.1.9 |
wirelessIfStatsChain2CtlRSSIThis parameter shows the control RSSI for the chain/antenna 2.ro Integer32 .1.3.6.1.4.1.841.1.1.3.4.5.1.1.10 |
wirelessIfStatsChain0ExtRSSIThis parameter shows the Extension RSSI for the chain/antenna 0.ro Integer32 .1.3.6.1.4.1.841.1.1.3.4.5.1.1.11 |
wirelessIfStatsChain1ExtRSSIThis parameter shows the Extension RSSI for the chain/antenna 1ro Integer32 .1.3.6.1.4.1.841.1.1.3.4.5.1.1.12 |
wirelessIfStatsChain2ExtRSSIThis parameter shows the Extension RSSI for the chain/antenna 2ro Integer32 .1.3.6.1.4.1.841.1.1.3.4.5.1.1.13 |
wirelessIfStatsCombinedRSSIThis parameter shows the combined RSSI of the control and extension.ro Integer32 .1.3.6.1.4.1.841.1.1.3.4.5.1.1.14 |
wirelessIfStatsPhyErrorsThis parameter shows the Physical layer errors.ro Integer32 .1.3.6.1.4.1.841.1.1.3.4.5.1.1.15 |
wirelessIfStatsRadioReTunesThis parameter shows the Number of times the radio is re-tuned.ro Integer32 .1.3.6.1.4.1.841.1.1.3.4.5.1.1.16 |
radiusMon OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.3.5 |
radiusClientStats OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.3.5.1 |
radiusClientAuthStatsTableThis table is used to store RADIUS Authentication Client Statistics for the configured profiles. SEQUENCE OF RadiusClientAuthStatsTableEntry .1.3.6.1.4.1.841.1.1.3.5.1.1 |
radiusClientAuthStatsTableEntryThis parameter represents an entry in the radiusClientAuthStatsTable. Note this table is indexed by VAP and Radius Pri/Sec servers RadiusClientAuthStatsTableEntry .1.3.6.1.4.1.841.1.1.3.5.1.1.1 |
radiusClientAuthStatsTableIndexThis parameter is user defined parameter and used as an index for Radius client Authorization status.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.5.1.1.1.1 |
radiusClientAuthStatsTableSecIndexThis parameter is secondary index to Radius client Authorisation status, 1 represents the primary server and 2 represents the secondary server.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.5.1.1.1.2 |
radiusClientAuthStatsRoundTripTimeThis parameter represents the round trip time for messages exchanged between radius client and authentication server since system startup.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.841.1.1.3.5.1.1.1.3 |
radiusClientAuthStatsRequestsThis parameter represents the number of RADIUS Access Requests messages transmitted from the client to the server since client startup.ro Counter32 .1.3.6.1.4.1.841.1.1.3.5.1.1.1.4 |
radiusClientAuthStatsRetransmissionsThis parameter represents the number of RADIUS Access Requests retransmitted by the client to the server since system startup.ro Counter32 .1.3.6.1.4.1.841.1.1.3.5.1.1.1.5 |
radiusClientAuthStatsAccessAcceptsThis parameter indicates the number of RADIUS Access Accept messages received since system startup.ro Counter32 .1.3.6.1.4.1.841.1.1.3.5.1.1.1.6 |
radiusClientAuthStatsAccessRejectsThis parameter represents the number of RADIUS Access Rejects messages received since system startup.ro Counter32 .1.3.6.1.4.1.841.1.1.3.5.1.1.1.7 |
radiusClientAuthStatsAccessChallengesThis parameter represents the number of RADIUS Access Challenges messages received since system startup.ro Counter32 .1.3.6.1.4.1.841.1.1.3.5.1.1.1.8 |
radiusClientAuthStatsResponsesThis parameter represents the total number of RADIUS Access messages received from the authentication server since system startup.ro Counter32 .1.3.6.1.4.1.841.1.1.3.5.1.1.1.9 |
radiusClientAuthStatsMalformedResponsesThis parameter represents the number of malformed RADIUS Access Response messages received since system startup.ro Counter32 .1.3.6.1.4.1.841.1.1.3.5.1.1.1.10 |
radiusClientAuthStatsBadAuthenticatorsThis parameter represents the number of malformed RADIUS Access Response messages containing invalid authenticators received since system startup.ro Counter32 .1.3.6.1.4.1.841.1.1.3.5.1.1.1.11 |
radiusClientAuthStatsTimeoutsThis parameters represents the total number of timeouts for RADIUS Access Request messages since system startup.ro Counter32 .1.3.6.1.4.1.841.1.1.3.5.1.1.1.12 |
radiusClientAuthStatsUnknownTypesThis parameter represents the number of messages with unknown Radius Message Code since system startup.ro Counter32 .1.3.6.1.4.1.841.1.1.3.5.1.1.1.13 |
radiusClientAuthStatsPacketsDroppedThis parameter represents the number of Radius messages which do not contain any EAP payloads or EAP State machine do not have any valid EAP state data since system startup.ro Counter32 .1.3.6.1.4.1.841.1.1.3.5.1.1.1.14 |
radiusClientAccStatsTableThis table is used to store RADIUS Accounting Client Statistics for the configured profiles. SEQUENCE OF RadiusClientAccStatsTableEntry .1.3.6.1.4.1.841.1.1.3.5.1.2 |
radiusClientAccStatsTableEntryThis parameter represents an entry in the radiusClientAccStatsTable. Note this table is indexed by VAP and Radius Pri/Sec servers. RadiusClientAccStatsTableEntry .1.3.6.1.4.1.841.1.1.3.5.1.2.1 |
radiusClientAccStatsTableIndexThis parameter is used as an index to the RADIUS Accounting Client Statistics Table.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.5.1.2.1.1 |
radiusClientAccStatsTableSecIndexThis parameter is used as secondary index to the RADIUS Accounting Client Statistics Table, which is used to indicate primary and secondary/backup server statistics, 1 represents the Primary server and 2 represents the Secondary server.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.5.1.2.1.2 |
radiusClientAccStatsRoundTripTimeThis parameter represents the round trip time for messages exchanged between radius client and authentication server since system startup .ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.841.1.1.3.5.1.2.1.3 |
radiusClientAccStatsRequestsThis parameter represents the number of RADIUS Accounting Requests messages transmitted from the client to the server since client startup.ro Counter32 .1.3.6.1.4.1.841.1.1.3.5.1.2.1.4 |
radiusClientAccStatsRetransmissionsThis parameter represents the number of RADIUS Accounting Requests retransmitted by the client to the server since system startup.ro Counter32 .1.3.6.1.4.1.841.1.1.3.5.1.2.1.5 |
radiusClientAccStatsResponsesThis parameter indicates the number of RADIUS Accounting Response messages received since system startup.ro Counter32 .1.3.6.1.4.1.841.1.1.3.5.1.2.1.6 |
radiusClientAccStatsMalformedResponsesThis parameter represents the number of malformed RADIUS Access Response messages received since system startup.ro Counter32 .1.3.6.1.4.1.841.1.1.3.5.1.2.1.7 |
radiusClientAccStatsTimeoutsThis parameter represents the total number of timeouts for RADIUS Accounting Response messages since the system startup.ro Counter32 .1.3.6.1.4.1.841.1.1.3.5.1.2.1.8 |
radiusClientAccStatsUnknownTypesThis parameter represents the number of messages with unknown Radius Message Code since system startup.ro Counter32 .1.3.6.1.4.1.841.1.1.3.5.1.2.1.9 |
radiusClientAccStatsPacketsDroppedThis parameter represents the number of Radius messages which do not contain any EAP payloads or EAP State machine do not have any valid EAP state data since system startup.ro Counter32 .1.3.6.1.4.1.841.1.1.3.5.1.2.1.10 |
traps OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.3.6 |
interfaceTraps OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.3.6.1 |
wirelessInterfaceCardInitFailureThis trap is generated when a wireless interface card is not present in the device or not initialized properly. Trap Severity Level: Critical. NOTIFICATION-TYPE .1.3.6.1.4.1.841.1.1.3.6.1.1 |
wirelessInterfaceCardRadarInterferenceDetectedThis trap is generated when radar interference is detected on the channel being used by the wireless interface. The generic trap varible provides information on the channel where interference was detected. Trap Severity Level: Major. NOTIFICATION-TYPE .1.3.6.1.4.1.841.1.1.3.6.1.2 |
wirelessInterfaceInvalidRegDomainThis trap is generated when the Regulatory Domain is invalid. Trap Severity Level: Major. NOTIFICATION-TYPE .1.3.6.1.4.1.841.1.1.3.6.1.3 |
wirelessInterfaceWorldModeCCNotSetThis trap is generated when the WorldModeCountryCode is not set. Trap Severity Level: Major. NOTIFICATION-TYPE .1.3.6.1.4.1.841.1.1.3.6.1.4 |
wirelessInterfaceChannelChangedThis trap is generated Wireless Interface Channel is changed. Trap Severity Level: Informational. NOTIFICATION-TYPE .1.3.6.1.4.1.841.1.1.3.6.1.5 |
securityTraps OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.3.6.2 |
radiusSrvNotRespondingThis trap is generated when no response is received from the RADIUS server(s) for authentication requests sent from the RADIUS client in the device. Trap Severity Level: Major. NOTIFICATION-TYPE .1.3.6.1.4.1.841.1.1.3.6.2.1 |
operationalTraps OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.3.6.3 |
masterAgentExitedThis trap is generated when the SNMP master agent is exited or killed. Trap Severity Level: Critical. NOTIFICATION-TYPE .1.3.6.1.4.1.841.1.1.3.6.3.1 |
imageDownloadFailedThis trap is generated when the image download is failed. Trap Severity Level: Critical. NOTIFICATION-TYPE .1.3.6.1.4.1.841.1.1.3.6.3.2 |
signatureCheckFailedThis trap is generated when the signature check is failed while downloading the image. Trap Severity Level: Critical. NOTIFICATION-TYPE .1.3.6.1.4.1.841.1.1.3.6.3.3 |
configurationAppliedSuccessfullyThis trap is generated when commit is passed, i.e., the changed configurations are applied successfully. Trap Severity Level: Major. NOTIFICATION-TYPE .1.3.6.1.4.1.841.1.1.3.6.3.4 |
systemTraps OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.3.6.4 |
invalidConfigFileThis trap is generated when an invalid image is loaded on the device. Trap Severity Level: Major. NOTIFICATION-TYPE .1.3.6.1.4.1.841.1.1.3.6.4.1 |
cpuUsageThresholdExceededThis trap is generated when the CPU usage threshold is exceeded. Trap Severity Level: Critical. NOTIFICATION-TYPE .1.3.6.1.4.1.841.1.1.3.6.4.2 |
flashMemoryThresholdExceededThis trap is generated when the flash memory is full or beyond the limit. Trap Severity Level: Critical. NOTIFICATION-TYPE .1.3.6.1.4.1.841.1.1.3.6.4.3 |
ramMemoryThresholdExceededThis trap is generated when the ram memory is full or beyond the limit. Trap Severity Level: Critical. NOTIFICATION-TYPE .1.3.6.1.4.1.841.1.1.3.6.4.4 |
invalidLicenseFileThis trap is generated when the invalid license file is loaded. Trap Severity Level: Critical. NOTIFICATION-TYPE .1.3.6.1.4.1.841.1.1.3.6.4.5 |
pxmModulesInitSuccessThis trap is generated when the initialization of all PXM MODULES is success. Trap Severity Level: Major. NOTIFICATION-TYPE .1.3.6.1.4.1.841.1.1.3.6.4.6 |
sysMgmtModulesInitFailureThis trap is generated when the initialization of SYSMGMT module is failed. Trap Severity Level: Major. NOTIFICATION-TYPE .1.3.6.1.4.1.841.1.1.3.6.4.7 |
vlanModuleInitFailureThis trap is generated when the initialization of VLAN module is failed. Trap Severity Level: Major. NOTIFICATION-TYPE .1.3.6.1.4.1.841.1.1.3.6.4.8 |
filteringModuleInitFailureThis trap is generated when the initialization of FILTERING module is failed. Trap Severity Level: Major. NOTIFICATION-TYPE .1.3.6.1.4.1.841.1.1.3.6.4.9 |
sysutilsModuleInitFailureThis trap is generated when the initialization of SYSUTILS module is failed. Trap Severity Level: Major. NOTIFICATION-TYPE .1.3.6.1.4.1.841.1.1.3.6.4.10 |
tftpModuleInitFailureThis trap is generated when the initialization of TFTP module is failed. Trap Severity Level: Major. NOTIFICATION-TYPE .1.3.6.1.4.1.841.1.1.3.6.4.11 |
sntpModuleInitFailureThis trap is generated when the initialization of SNTP module is failed. Trap Severity Level: Major. NOTIFICATION-TYPE .1.3.6.1.4.1.841.1.1.3.6.4.12 |
syslogModuleInitFailureThis trap is generated when the initialization of SYSLOG module is failed. Trap Severity Level: Major. NOTIFICATION-TYPE .1.3.6.1.4.1.841.1.1.3.6.4.13 |
wlanModuleInitFailureThis trap is generated when the initialization of WLAN module is failed. Trap Severity Level: Major. NOTIFICATION-TYPE .1.3.6.1.4.1.841.1.1.3.6.4.14 |
flashModuleInitFailureThis trap is generated when the initialization of FLASH module is failed. Trap Severity Level: Major. NOTIFICATION-TYPE .1.3.6.1.4.1.841.1.1.3.6.4.15 |
snmpModuleInitFailureThis trap is generated when the initialization of SNMP module is failed. Trap Severity Level: Major. NOTIFICATION-TYPE .1.3.6.1.4.1.841.1.1.3.6.4.16 |
systemTempReachedLimitsThis trap is generated when the system temperature reaches the maximum/ minimum limits or the proximity of the max/min limits. Trap Severity Level: Major. NOTIFICATION-TYPE .1.3.6.1.4.1.841.1.1.3.6.4.17 |
dhcpRelayModuleInitFailureThis trap is generated when the initialization of DHCP Relay module is failed. Trap Severity Level: Major. NOTIFICATION-TYPE .1.3.6.1.4.1.841.1.1.3.6.4.18 |
dhcpServerModuleInitFailureThis trap is generated when the initialization of DHCP Server module is failed. Trap Severity Level: Major. NOTIFICATION-TYPE .1.3.6.1.4.1.841.1.1.3.6.4.19 |
staticNATModuleInitFailureThis trap is generated when the initialization of Static NAT module is failed. Trap Severity Level: Major. NOTIFICATION-TYPE .1.3.6.1.4.1.841.1.1.3.6.4.20 |
licenseModuleInitFailureThis trap is generated when the initialization of License module is failed. Trap Severity Level: Major. NOTIFICATION-TYPE .1.3.6.1.4.1.841.1.1.3.6.4.21 |
systemFeatureModuleInitFailureThis trap is generated when the initialization of System Features module is failed. Trap Severity Level: Major. NOTIFICATION-TYPE .1.3.6.1.4.1.841.1.1.3.6.4.22 |
mgmtAccessModuleInitFailureThis trap is generated when the initialization of Management Access module is failed. Trap Severity Level: Major. NOTIFICATION-TYPE .1.3.6.1.4.1.841.1.1.3.6.4.23 |
routingModuleInitFailureThis trap is generated when the initialization of Routing module is failed. Trap Severity Level: Major. NOTIFICATION-TYPE .1.3.6.1.4.1.841.1.1.3.6.4.24 |
sntpTraps OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.3.6.5 |
sntpFailureThis trap is generated when the SNTP fails to get the time from SNTP server. Trap Severity Level: Major. NOTIFICATION-TYPE .1.3.6.1.4.1.841.1.1.3.6.5.1 |
imageTraps OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.3.6.6 |
invalidImageThis trap is generated when the image loaded is invalid or too large or incompatible. Trap Severity Level: Major. NOTIFICATION-TYPE .1.3.6.1.4.1.841.1.1.3.6.6.1 |
siteSurvey OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.3.7 |
worpSiteSurvey OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.3.7.1 |
worpSiteSurveyOperationTableThis table contains the information about all the BSU which all are visible for this SU. SEQUENCE OF WorpSiteSurveyOperationTableEntry .1.3.6.1.4.1.841.1.1.3.7.1.1 |
worpSiteSurveyOperationTableEntryThis parameter represents the entry in the worpSiteSurvey operation table. WorpSiteSurveyOperationTableEntry .1.3.6.1.4.1.841.1.1.3.7.1.1.1 |
worpSiteSurveyOperationTableIndexThis parameter represents the index to the worpSiteSurveyOperationTable.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.7.1.1.1.1 |
worpSiteSurveyOperationIfNameThis parameter shows the wireless interface name for which site survey parameters are shown.ro DisplayString .1.3.6.1.4.1.841.1.1.3.7.1.1.1.2 |
worpSiteSurveyOperationStatusThis parameter is used enable/disable the site survey operation.rw Enumeration .1.3.6.1.4.1.841.1.1.3.7.1.1.1.3 |
worpSiteSurveyTableThis table contains the information about all the BSU which all are visible for this SU. SEQUENCE OF WorpSiteSurveyTableEntry .1.3.6.1.4.1.841.1.1.3.7.1.2 |
worpSiteSurveyTableEntryThis parameter represents the entry in the worpSiteSurvey table. WorpSiteSurveyTableEntry .1.3.6.1.4.1.841.1.1.3.7.1.2.1 |
worpSiteSurveyTableIndexThis parameter represents te index to the worpSiteSurveyTable.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.7.1.2.1.1 |
worpSiteSurveyTableSecIndexThis parameter represents te index to the worpSiteSurveyTable.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.7.1.2.1.2 |
worpSiteSurveyBaseMACAddressThis parameter represents the MAC address of the BSU.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.3.7.1.2.1.3 |
worpSiteSurveyBaseNameThis parameter represents the name of the BSU.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.3.7.1.2.1.4 |
worpSiteSurveyMaxSatellitesAllowedThis parameter represents the maximum number of satellites allowed to register with this BSU.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.7.1.2.1.5 |
worpSiteSurveyNumSatellitesRegisteredThis parameter represents the number of satellites currently registered on this BSU.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.7.1.2.1.6 |
worpSiteSurveySatelliteRegisteredStatusThis parameter represents the registration status of this satellite on the BSU.ro Enumeration .1.3.6.1.4.1.841.1.1.3.7.1.2.1.7 |
worpSiteSurveyLocalTxRateThis parameter represents the transmission rate of the SU. This field is not valid if the registration status is Not-Registeredro Unsigned32 .1.3.6.1.4.1.841.1.1.3.7.1.2.1.8 |
worpSiteSurveyRemoteTxRateThis parameter represents the transmission rate of the BSU. This field is not valid if the registration status is Not-Registeredro Unsigned32 .1.3.6.1.4.1.841.1.1.3.7.1.2.1.9 |
worpSiteSurveyLocalSignalLevelThis parameter displays the current signal level of the incoming wireless frames from this BSU.ro Integer32 .1.3.6.1.4.1.841.1.1.3.7.1.2.1.10 |
worpSiteSurveyLocalNoiseLevelThis parameter displays the current noise level of the incoming wireless frames from this BSU.ro Integer32 .1.3.6.1.4.1.841.1.1.3.7.1.2.1.11 |
worpSiteSurveyLocalSNRThis parameter represents the current Local SNR.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.7.1.2.1.12 |
worpSiteSurveyRemoteSignalLevelThis parameter displays the current signal level of the incoming wireless frames at BSU. This field is not valid if the registration status is Not-Registeredro Integer32 .1.3.6.1.4.1.841.1.1.3.7.1.2.1.13 |
worpSiteSurveyRemoteNoiseLevelThis parameter displays the current noise level of the incoming wireless frames at BSU. This field is not valid if the registration status is Not-Registered.ro Integer32 .1.3.6.1.4.1.841.1.1.3.7.1.2.1.14 |
worpSiteSurveyRemoteSNRThis parameter represents the current SNR at BSU. This field is not valid if the registration status is Not-Registeredro Unsigned32 .1.3.6.1.4.1.841.1.1.3.7.1.2.1.15 |
worpSiteSurveyChannelThis parameter represents the channel at which the BSU is operating.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.7.1.2.1.16 |
worpSiteSurveyChannelBandwidthThis parameter represents the BSU channel bandwidth.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.7.1.2.1.17 |
worpSiteSurveyChannelRxRateThis parameter represents the Rx rate of BSU.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.7.1.2.1.18 |
worpSiteSurveyBaseBridgePortThis parameter represents the SU's Bridge port for which BSU is connected.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.7.1.2.1.19 |
worpSiteSurveyLocalMimoCtrlSig1This parameter represents the Rx rate of BSU.ro Integer32 .1.3.6.1.4.1.841.1.1.3.7.1.2.1.20 |
worpSiteSurveyLocalMimoCtrlSig2This parameter represents the Rx rate of BSU.ro Integer32 .1.3.6.1.4.1.841.1.1.3.7.1.2.1.21 |
worpSiteSurveyLocalMimoCtrlSig3This parameter represents the Rx rate of BSU.ro Integer32 .1.3.6.1.4.1.841.1.1.3.7.1.2.1.22 |
worpSiteSurveyLocalMimoNoiseThis parameter represents the Rx rate of BSU.ro Integer32 .1.3.6.1.4.1.841.1.1.3.7.1.2.1.23 |
worpSiteSurveyLocalMimoCtrlSNR1This parameter represents the Rx rate of BSU.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.7.1.2.1.24 |
worpSiteSurveyLocalMimoCtrlSNR2This parameter represents the Rx rate of BSU.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.7.1.2.1.25 |
worpSiteSurveyLocalMimoCtrlSNR3This parameter represents the Rx rate of BSU.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.7.1.2.1.26 |
worpSiteSurveyRemoteMimoCtrlSig1This parameter represents the Rx rate of BSU.ro Integer32 .1.3.6.1.4.1.841.1.1.3.7.1.2.1.27 |
worpSiteSurveyRemoteMimoCtrlSig2This parameter represents the Rx rate of BSU.ro Integer32 .1.3.6.1.4.1.841.1.1.3.7.1.2.1.28 |
worpSiteSurveyRemoteMimoCtrlSig3This parameter represents the Rx rate of BSU.ro Integer32 .1.3.6.1.4.1.841.1.1.3.7.1.2.1.29 |
worpSiteSurveyRemoteMimoNoiseThis parameter represents the Rx rate of BSU.ro Integer32 .1.3.6.1.4.1.841.1.1.3.7.1.2.1.30 |
worpSiteSurveyRemoteMimoCtrlSNR1This parameter represents the Rx rate of BSU.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.7.1.2.1.31 |
worpSiteSurveyRemoteMimoCtrlSNR2This parameter represents the Rx rate of BSU.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.7.1.2.1.32 |
worpSiteSurveyRemoteMimoCtrlSNR3This parameter represents the Rx rate of BSU.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.7.1.2.1.33 |
worpSiteSurveyLocalChainBalStatusWhen this parameter indicates the local chain balance status.ro Enumeration .1.3.6.1.4.1.841.1.1.3.7.1.2.1.34 |
worpSiteSurveyRemoteChainBalStatusWhen this parameter indicates the remote chain balance status.ro Enumeration .1.3.6.1.4.1.841.1.1.3.7.1.2.1.35 |
temperature OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.3.8 |
currentUnitTempThis parameter is used for the internal unit temperature in degrees celsius. The range of the temperature is -30 to 60 degrees celsius.ro Integer32 (-40..60) .1.3.6.1.4.1.841.1.1.3.8.1 |
highTempThresholdThis parameter is used set the high temperature threshold by the user.rw Integer32 (-40..60) .1.3.6.1.4.1.841.1.1.3.8.2 |
lowTempThresholdThis parameter is used set the low temperature threshold by the user.rw Integer32 (-40..60) .1.3.6.1.4.1.841.1.1.3.8.3 |
tempLoggingIntervalThis parameter is used for logging interval. The valid values are 1,5,10,15,20,25,30,35,40,45,50,55,and 60.rw Integer32 .1.3.6.1.4.1.841.1.1.3.8.4 |
tempLogResetThis parameter is used for reset/clear the temperature log.rw Enumeration .1.3.6.1.4.1.841.1.1.3.8.5 |
sysMonitor OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.3.9 |
sysMonitorCPUUsageThis parameter shows the present CPU usage.ro DisplayString .1.3.6.1.4.1.841.1.1.3.9.1 |
sysMonitorRAMUsageThis parameter shows the present RAM usage.ro DisplayString .1.3.6.1.4.1.841.1.1.3.9.2 |
igmpStats OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.3.10 |
igmpEthernetSnoopingStats OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.3.10.1 |
igmpEth1MCastTableThis table holds the IGMP multicast IP and MAC address details for the ethernet interface 1 SEQUENCE OF IgmpEth1MCastTableEntry .1.3.6.1.4.1.841.1.1.3.10.1.1 |
igmpEth1MCastTableEntryThis parameter represents the entry for this table. IgmpEth1MCastTableEntry .1.3.6.1.4.1.841.1.1.3.10.1.1.1 |
igmpEth1MCastTableIndexThis parameter represents the index for this table.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.10.1.1.1.1 |
igmpEth1MCastGrpIpThis parameter indicates the IP multicast address of ethernet interface 1 learned by IGMP snooping.ro IpAddress .1.3.6.1.4.1.841.1.1.3.10.1.1.1.2 |
igmpEth1MCastGrpMACAddrThis parameter indicates the Mac multicast address of ethernet interface 1 learned by IGMP snooping.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.3.10.1.1.1.3 |
igmpEth1MCastGrpAgingTimeElapsedThis parameter specifies the aging time for multicast entries for the ethernet interface 1.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.841.1.1.3.10.1.1.1.4 |
igmpEth2MCastTableThis table holds the IGMP multicast IP and MAC address details for the ethernet interface 2 SEQUENCE OF IgmpEth2MCastTableEntry .1.3.6.1.4.1.841.1.1.3.10.1.2 |
igmpEth2MCastTableEntryThis parameter represents the entry for this table. IgmpEth2MCastTableEntry .1.3.6.1.4.1.841.1.1.3.10.1.2.1 |
igmpEth2MCastTableIndexThis parameter represents the index for this table.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.10.1.2.1.1 |
igmpEth2MCastGrpIpThis parameter indicates the IP multicast address of ethernet interface 2 learned by IGMP snooping.ro IpAddress .1.3.6.1.4.1.841.1.1.3.10.1.2.1.2 |
igmpEth2MCastGrpMACAddrThis parameter indicates the Mac multicast address of ethernet interface 2 learned by IGMP snooping.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.3.10.1.2.1.3 |
igmpEth2MCastGrpAgingTimeElapsedThis parameter specifies the aging time for multicast entries for the ethernet interface 2.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.841.1.1.3.10.1.2.1.4 |
igmpWirelessSnoopingStats OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.3.10.2 |
igmpWireless1MCastTableThis table holds the IGMP multicast IP and MAC address details for the wireless interface 1. SEQUENCE OF IgmpWireless1MCastTableEntry .1.3.6.1.4.1.841.1.1.3.10.2.1 |
igmpWireless1MCastTableEntryThis parameter represents the entry for the wireless multicast table. IgmpWireless1MCastTableEntry .1.3.6.1.4.1.841.1.1.3.10.2.1.1 |
igmpWireless1MCastTableIndexThis parameter represents the index for this table.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.10.2.1.1.1 |
igmpWireless1MCastGrpIpThis parameter indicates the IP multicast address of wireless interface 1 learned by IGMP snooping.ro IpAddress .1.3.6.1.4.1.841.1.1.3.10.2.1.1.2 |
igmpWireless1MCastGrpMACAddrThis parameter indicates the Mac multicast address of wireless interface 1 learned by IGMP snooping.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.841.1.1.3.10.2.1.1.3 |
igmpWireless1MCastGrpAgingTimeElapsedThis parameter specifies the aging time for multicast entries for the wireless interface 1.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.841.1.1.3.10.2.1.1.4 |
igmpRouterPortListTableThis table shows the IGMP router port stats for all interfaces. SEQUENCE OF IgmpRouterPortListTableEntry .1.3.6.1.4.1.841.1.1.3.10.3 |
igmpRouterPortListTableEntryThis parameter represents the entry for the router port list table. IgmpRouterPortListTableEntry .1.3.6.1.4.1.841.1.1.3.10.3.1 |
igmpRouterPortListTableIndexThis paramter represents the interface number or index to this table.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.10.3.1.1 |
igmpRouterPortNumberThis parameter represents the router port number on which IGMP snooping/listening is done.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.10.3.1.2 |
igmpRouterAgingTimeElapsedThis parameter represents the time elapsed since snooping is started on the router port.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.841.1.1.3.10.3.1.3 |
debugLog OBJECT IDENTIFIER .1.3.6.1.4.1.841.1.1.3.11 |
debugLogBitMaskThis parameter specifies which debug levels are enabled. It is Bit Mask field. Bits are defined as follows Bit0 - WORP general debug level. Bit1 - DDRS debug level one. Bit2 - DDRS debug level two. Bit3 - DDRS debug level three.rw Unsigned32 .1.3.6.1.4.1.841.1.1.3.11.1 |
debugLogResetThis parameter is used to reset/clear the debug log messages. When this parameter is set, then all enteries in the event log table are deleted/cleared. Select (1) to reset the table.rw Enumeration .1.3.6.1.4.1.841.1.1.3.11.2 |
debugLogSizeThis parameter represents number line present in the debuglog file.ro Unsigned32 .1.3.6.1.4.1.841.1.1.3.11.3 |
products OBJECT IDENTIFIER .1.3.6.1.4.1.841.2 |
ap_800 OBJECT IDENTIFIER .1.3.6.1.4.1.841.2.1 |
ap_8000 OBJECT IDENTIFIER .1.3.6.1.4.1.841.2.2 |
qb_8100 OBJECT IDENTIFIER .1.3.6.1.4.1.841.2.11 |
mp_8100 OBJECT IDENTIFIER .1.3.6.1.4.1.841.2.21 |
mp_8100_cpe OBJECT IDENTIFIER .1.3.6.1.4.1.841.2.22 |