PIMG-MIB
The MIB module for management of PIM routers.
Main OID:
pimgMIB.1.3.6.1.3.1
86
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
86 total| Object Name |
|---|
pimgMIBThe MIB module for management of PIM routers. MODULE-IDENTITY .1.3.6.1.3.1 |
pimgMIBObjects OBJECT IDENTIFIER .1.3.6.1.3.1.1 |
pimgTraps OBJECT IDENTIFIER .1.3.6.1.3.1.1.0 |
pimgNeighborLossA pimgNeighborLoss trap signifies the loss of an adjacency with a neighbor. This trap should be generated when the neighbor timer expires, and the router has no other neighbors on the same interface with a lower IP address than itself. NOTIFICATION-TYPE .1.3.6.1.3.1.1.0.1 |
pimg OBJECT IDENTIFIER .1.3.6.1.3.1.1.1 |
pimgJoinPruneIntervalThe default interval at which periodic PIM-SM Join/Prune messages are to be sent.rw Integer32 UNITS "seconds" .1.3.6.1.3.1.1.1.1 |
pimgInterfaceTableThe (conceptual) table listing the router's PIM interfaces. IGMP and PIM are enabled on all interfaces listed in this table. SEQUENCE OF PimgInterfaceEntry .1.3.6.1.3.1.1.1.2 |
pimgInterfaceEntryAn entry (conceptual row) in the pimgInterfaceTable. PimgInterfaceEntry .1.3.6.1.3.1.1.1.2.1 |
pimgInterfaceIfIndexThe ifIndex value of this PIM interface. InterfaceIndex (IF-MIB) .1.3.6.1.3.1.1.1.2.1.1 |
pimgInterfaceAddressTypeA value indicating the address family of the address contained in pimgInterfaceAddress. Legal values correspond to the subset of address families for which PIM routing is supported.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.3.1.1.1.2.1.2 |
pimgInterfaceAddressThe IP address of the PIM interface.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.3.1.1.1.2.1.3 |
pimgInterfaceNetMaskLenThe length in bits of the network mask which when combined with the corresponding value of pimgInterfaceAddress identifies the address of the network to which the PIM interface is attached.ro INTEGER .1.3.6.1.3.1.1.1.2.1.4 |
pimgInterfaceModeThe configured mode of this PIM interface. A value of sparseDense is only valid for PIMv1.rw Enumeration .1.3.6.1.3.1.1.1.2.1.5 |
pimgInterfaceDRTypeA value indicating the address family of the address contained in pimgInterfaceDR. The value MUST be the same as the value of pimgInterfaceAddressType.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.3.1.1.1.2.1.6 |
pimgInterfaceDRThe Designated Router on this PIM interface. For point-to-point interfaces, pimgInterfaceDR will be 0.0.0.0 in the case of an IPv4 entry, and 0:0:0:0:0:0:0:0 in the case of an IPv6 entry.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.3.1.1.1.2.1.7 |
pimgInterfaceHelloIntervalThe frequency at which PIM Hello messages are transmitted on this interface.rw Integer32 UNITS "seconds" .1.3.6.1.3.1.1.1.2.1.8 |
pimgInterfaceStatusThe status of this entry. Creating the entry enables PIM on the interface; destroying the entry disables PIM on the interface.rw RowStatus (SNMPv2-TC) .1.3.6.1.3.1.1.1.2.1.9 |
pimgInterfaceJoinPruneIntervalThe frequency at which PIM Join/Prune messages are transmitted on this PIM interface. The default value of this object is the pimgJoinPruneInterval.rw Integer32 UNITS "seconds" .1.3.6.1.3.1.1.1.2.1.10 |
pimgInterfaceCBSRPreferenceThe preference value for the local interface as a candidate bootstrap router. The value of -1 is used to indicate that the local interface is not a candidate BSR interface.rw Integer32 (-1..255) .1.3.6.1.3.1.1.1.2.1.11 |
pimgNeighborTableThe (conceptual) table listing the router's PIM neighbors. SEQUENCE OF PimgNeighborEntry .1.3.6.1.3.1.1.1.3 |
pimgNeighborEntryAn entry (conceptual row) in the pimgNeighborTable. PimgNeighborEntry .1.3.6.1.3.1.1.1.3.1 |
pimgNeighborAddressTypeA value indicating the address family of the address contained in pimgNeighborAddress. Legal values correspond to the subset of address families for which PIM routing is supported. InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.3.1.1.1.3.1.1 |
pimgNeighborAddressThe IP address of the PIM neighbor for which this entry contains information. InetAddress (INET-ADDRESS-MIB) .1.3.6.1.3.1.1.1.3.1.2 |
pimgNeighborIfIndexThe value of ifIndex for the interface used to reach this PIM neighbor.ro InterfaceIndex (IF-MIB) .1.3.6.1.3.1.1.1.3.1.3 |
pimgNeighborUpTimeThe time since this PIM neighbor (last) became a neighbor of the local router.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.3.1.1.1.3.1.4 |
pimgNeighborExpiryTimeThe minimum time remaining before this PIM neighbor will be aged out.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.3.1.1.1.3.1.5 |
pimgNeighborModeThe active PIM mode of this neighbor. This object is deprecated for PIMv2 routers since all neighbors on the interface must be either dense or sparse as determined by the protocol running on the interface.rodeprecated Enumeration .1.3.6.1.3.1.1.1.3.1.6 |
pimgInetMRouteTableThe (conceptual) table listing PIM-specific information on a subset of the rows of the inetMRouteTable defined in the Inet Multicast MIB. SEQUENCE OF PimgInetMRouteEntry .1.3.6.1.3.1.1.1.4 |
pimgInetMRouteEntryAn entry (conceptual row) in the pimgInetMRouteTable. There is one entry per entry in the inetMRouteTable whose incoming interface is running PIM. PimgInetMRouteEntry .1.3.6.1.3.1.1.1.4.1 |
pimgInetMRouteUpstreamAssertTimerThe time remaining before the router changes its upstream neighbor back to its RPF neighbor. This timer is called the Assert timer in the PIM Sparse and Dense mode specification. A value of 0 indicates that no Assert has changed the upstream neighbor away from the RPF neighbor.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.3.1.1.1.4.1.1 |
pimgInetMRouteAssertMetricThe metric advertised by the assert winner on the upstream interface, or 0 if no such assert is in received.ro Integer32 .1.3.6.1.3.1.1.1.4.1.2 |
pimgInetMRouteAssertMetricPrefThe preference advertised by the assert winner on the upstream interface, or 0 if no such assert is in effect.ro Integer32 .1.3.6.1.3.1.1.1.4.1.3 |
pimgInetMRouteAssertRPTBitThe value of the RPT-bit advertised by the assert winner on the upstream interface, or false if no such assert is in effect.ro TruthValue (SNMPv2-TC) .1.3.6.1.3.1.1.1.4.1.4 |
pimgInetMRouteFlagsThis object describes PIM-specific flags related to a multicast state entry. See the PIM Sparse Mode specification for the meaning of the RPT and SPT bits.ro Bits .1.3.6.1.3.1.1.1.4.1.5 |
pimgRPTableThe (conceptual) table listing PIM version 1 information for the Rendezvous Points (RPs) for multicast groups. This table is deprecated since its function is replaced by the pimgRPSetTable for PIM version 2.deprecated SEQUENCE OF PimgRPEntry .1.3.6.1.3.1.1.1.5 |
pimgRPEntryAn entry (conceptual row) in the pimgRPTable. There is one entry per RP address for each multicast group.deprecated PimgRPEntry .1.3.6.1.3.1.1.1.5.1 |
pimgRPGroupAddressTypeA value indicating the address family of the address contained in pimgRPGroupAddress. Legal values are: unknown(0), ipv4(1), ipv6(2), dns(16)deprecated InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.3.1.1.1.5.1.1 |
pimgRPGroupAddressThe multicast group address for which this entry contains information about an RP.deprecated InetAddress (INET-ADDRESS-MIB) .1.3.6.1.3.1.1.1.5.1.2 |
pimgRPAddressTypeA value indicating the address family of the address contained in pimgRPAddress. The value MUST be the same as the value of pimgRPGroupAddressType.deprecated InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.3.1.1.1.5.1.3 |
pimgRPAddressThe unicast address of the RP.deprecated InetAddress (INET-ADDRESS-MIB) .1.3.6.1.3.1.1.1.5.1.4 |
pimgRPStateThe state of the RP.rodeprecated Enumeration .1.3.6.1.3.1.1.1.5.1.5 |
pimgRPStateTimerThe minimum time remaining before the next state change. When pimgRPState is up, this is the minimum time which must expire until it can be declared down. When pimgRPState is down, this is the time until it will be declared up (in order to retry).rodeprecated TimeTicks (SNMPv2-SMI) .1.3.6.1.3.1.1.1.5.1.6 |
pimgRPLastChangeThe value of sysUpTime at the time when the corresponding instance of pimgRPState last changed its value.rodeprecated TimeTicks (SNMPv2-SMI) .1.3.6.1.3.1.1.1.5.1.7 |
pimgRPRowStatusThe status of this row, by which new entries may be created, or old entries deleted from this table.rwdeprecated RowStatus (SNMPv2-TC) .1.3.6.1.3.1.1.1.5.1.8 |
pimgRPSetTableThe (conceptual) table listing PIM information for candidate Rendezvous Points (RPs) for multicast groups. When the local router is the BSR, this information is obtained from received Candidate-RP- Advertisements. When the local router is not the BSR, this information is obtained from received RP- Set messages. SEQUENCE OF PimgRPSetEntry .1.3.6.1.3.1.1.1.6 |
pimgRPSetEntryAn entry (conceptual row) in the pimgRPSetTable. PimgRPSetEntry .1.3.6.1.3.1.1.1.6.1 |
pimgRPSetGroupAddressTypeA value indicating the address family of the address contained in pimgRPSetGroupAddress. Legal values correspond to the subset of address families for which PIM routing is supported. InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.3.1.1.1.6.1.1 |
pimgRPSetGroupAddressThe IP multicast group address which, when combined with the value of pimgRPSetGroupMaskLen, gives the group prefix for which this entry contains information about the Candidate-RP. InetAddress (INET-ADDRESS-MIB) .1.3.6.1.3.1.1.1.6.1.2 |
pimgRPSetGroupMaskLenThe length in bits of the mask which, when combined with pimgRPSetGroupAddress, gives the group prefix for which this entry contains information about the Candidate-RP. INTEGER .1.3.6.1.3.1.1.1.6.1.3 |
pimgRPSetAddressTypeA value indicating the address family of the address contained in pimgRPSetAddress. The value MUST be the same as the value of pimgRPSetGroupAddressType. InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.3.1.1.1.6.1.4 |
pimgRPSetAddressThe address of the Candidate-RP. InetAddress (INET-ADDRESS-MIB) .1.3.6.1.3.1.1.1.6.1.5 |
pimgRPSetHoldTimeThe holdtime of a Candidate-RP. If the local router is not the BSR, this value is 0.ro Integer32 .1.3.6.1.3.1.1.1.6.1.6 |
pimgRPSetExpiryTimeThe minimum time remaining before the Candidate-RP will be declared down. If the local router is not the BSR, this value is 0.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.3.1.1.1.6.1.7 |
pimgRPSetComponentA number uniquely identifying the component. Each protocol instance connected to a separate domain should have a different index value. Integer32 .1.3.6.1.3.1.1.1.6.1.8 |
pimgInetMRouteNextHopTableThe (conceptual) table listing PIM-specific information on a subset of the rows of the inetMRouteNextHopTable defined in the IP Multicast MIB. SEQUENCE OF PimgInetMRouteNextHopEntry .1.3.6.1.3.1.1.1.7 |
pimgInetMRouteNextHopEntryAn entry (conceptual row) in the pimgInetMRouteNextHopTable. There is one entry per entry in the inetMRouteNextHopTable whose interface is running PIM and whose inetMRouteNextHopState is pruned(1). PimgInetMRouteNextHopEntry .1.3.6.1.3.1.1.1.7.1 |
pimgInetMRouteNextHopPruneReasonThis object indicates why the downstream interface was pruned, whether in response to a PIM prune message or due to PIM Assert processing.ro Enumeration .1.3.6.1.3.1.1.1.7.1.2 |
pimgCandidateRPTableThe (conceptual) table listing the multicast groups for which the local router is to advertise itself as a Candidate-RP when the value of pimgComponentCRPHoldTime is non-zero. If this table is empty, then the local router will advertise itself as a Candidate-RP for all groups (providing the value of pimgComponentCRPHoldTime is non-zero). SEQUENCE OF PimgCandidateRPEntry .1.3.6.1.3.1.1.1.11 |
pimgCandidateRPEntryAn entry (conceptual row) in the pimgCandidateRPTable. PimgCandidateRPEntry .1.3.6.1.3.1.1.1.11.1 |
pimgCandidateRPGroupAddressTypeA value indicating the address family of the address contained in pimgCandidateRPGroupAddress. Legal values correspond to the subset of address families for which PIM routing is supported. InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.3.1.1.1.11.1.1 |
pimgCandidateRPGroupAddressThe multicast group address which, when combined with the corresponding value of pimgCandidateRPGroupMaskLen, identifies a group prefix for which the local router will advertise itself as a Candidate-RP. InetAddress (INET-ADDRESS-MIB) .1.3.6.1.3.1.1.1.11.1.2 |
pimgCandidateRPGroupMaskLenThe length in bits of the mask which, when combined with pimgCandidateRPGroupAddress, identifies a group prefix for which the local router will advertise itself as a Candidate-RP. INTEGER .1.3.6.1.3.1.1.1.11.1.3 |
pimgCandidateRPAddressTypeA value indicating the address family of the address contained in pimgCandidateRPAddress. The value MUST be the same as the value of pimgCandidateRPGroupAddressType.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.3.1.1.1.11.1.4 |
pimgCandidateRPAddressThe (unicast) address of the interface which will be advertised as a Candidate-RP.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.3.1.1.1.11.1.5 |
pimgCandidateRPRowStatusThe status of this row, by which new entries may be created, or old entries deleted from this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.3.1.1.1.11.1.6 |
pimgComponentTableThe (conceptual) table containing objects specific to a PIM domain. One row exists for each domain to which the router is connected. A PIM-SM domain is defined as an area of the network over which Bootstrap messages are forwarded. Typically, a PIM- SM router will be a member of exactly one domain. This table also supports, however, routers which may form a border between two PIM-SM domains and do not forward Bootstrap messages between them. SEQUENCE OF PimgComponentEntry .1.3.6.1.3.1.1.1.12 |
pimgComponentEntryAn entry (conceptual row) in the pimgComponentTable. PimgComponentEntry .1.3.6.1.3.1.1.1.12.1 |
pimgComponentIndexA number uniquely identifying the component. Each protocol instance connected to a separate domain should have a different index value. Routers that only support membership in a single PIM-SM domain should use a pimgComponentIndex value of 1. Integer32 .1.3.6.1.3.1.1.1.12.1.1 |
pimgComponentBSRAddressTypeA value indicating the address family of the address contained in pimgComponentBSRAddress. Legal values correspond to the subset of address families for which PIM routing is supported.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.3.1.1.1.12.1.2 |
pimgComponentBSRAddressThe address of the bootstrap router (BSR) for the local PIM region.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.3.1.1.1.12.1.3 |
pimgComponentBSRExpiryTimeThe minimum time remaining before the bootstrap router in the local domain will be declared down. For candidate BSRs, this is the time until the component sends an RP-Set message. For other routers, this is the time until it may accept an RP-Set message from a lower candidate BSR.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.3.1.1.1.12.1.4 |
pimgComponentCRPHoldTimeThe holdtime of the component when it is a candidate RP in the local domain. The value of 0 is used to indicate that the local system is not a Candidate-RP.rw Integer32 .1.3.6.1.3.1.1.1.12.1.5 |
pimgComponentStatusThe status of this entry. Creating the entry creates another protocol instance; destroying the entry disables a protocol instance.rw RowStatus (SNMPv2-TC) .1.3.6.1.3.1.1.1.12.1.6 |
pimgMIBConformance OBJECT IDENTIFIER .1.3.6.1.3.1.2 |
pimgMIBCompliances OBJECT IDENTIFIER .1.3.6.1.3.1.2.1 |
pimgV1MIBComplianceThe compliance statement for routers running PIMv1 and implementing the PIM MIB.deprecated Unknown .1.3.6.1.3.1.2.1.1 |
pimgSparseV2MIBComplianceThe compliance statement for routers running PIM Sparse Mode and implementing the PIM MIB. Unknown .1.3.6.1.3.1.2.1.2 |
pimgDenseV2MIBComplianceThe compliance statement for routers running PIM Dense Mode and implementing the PIM MIB. Unknown .1.3.6.1.3.1.2.1.3 |
pimgMIBGroups OBJECT IDENTIFIER .1.3.6.1.3.1.2.2 |
pimgNotificationGroupA collection of notifications for signaling important PIM events. Unknown .1.3.6.1.3.1.2.2.1 |
pimgV2MIBGroupA collection of objects to support management of PIM Sparse Mode (version 2) routers. Unknown .1.3.6.1.3.1.2.2.2 |
pimgV2CandidateRPMIBGroupA collection of objects to support configuration of which groups a router is to advertise itself as a Candidate-RP. Unknown .1.3.6.1.3.1.2.2.3 |
pimgV1MIBGroupA collection of objects to support management of PIM (version 1) routers.deprecated Unknown .1.3.6.1.3.1.2.2.4 |
pimgNextHopGroupA collection of optional objects to provide per- next hop information for diagnostic purposes. Supporting this group may add a large number of instances to a tree walk, but the information in this group can be extremely useful in tracking down multicast connectivity problems. Unknown .1.3.6.1.3.1.2.2.5 |
pimgAssertGroupA collection of optional objects to provide extra information about the assert election process. There is no protocol reason to keep such information, but some implementations may already keep this information and make it available. These objects can also be very useful in debugging connectivity or duplicate packet problems, especially if the assert winner does not support the PIM and Inet Multicast MIBs. Unknown .1.3.6.1.3.1.2.2.6 |
pimgDenseV2MIBGroupA collection of objects to support management of PIM Dense Mode (version 2) routers. Unknown .1.3.6.1.3.1.2.2.7 |