OSPF-TRAP-MIB
The OSPF-TRAP-MIB defines standardized SNMP trap notifications for OSPF Version 2 to alert network management systems about critical protocol state transitions, including neighbor adjacency changes, interface state shifts, and LSA flooding events. These traps enable real-time detection of routing instability and topology changes without requiring active polling of the OSPF process.
Imported Objects
Objects
17 total| Object Name |
|---|
ospfTrapThe MIB module to describe traps for the OSPF
Version 2 Protocol. MODULE-IDENTITY .1.3.6.1.4.1.727.7.2.15.16 |
ospfTrapControl OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.15.16.1 |
ospfConfigErrorTypePotential types of configuration conflicts.
Used by the ospfConfigError and ospfConfigVir-
tError traps.ro Enumeration .1.3.6.1.4.1.727.7.2.15.16.1.2 |
ospfPacketTypeOSPF packet types.ro Enumeration .1.3.6.1.4.1.727.7.2.15.16.1.3 |
ospfPacketSrcThe IP address of an inbound packet that can-
not be identified by a neighbor instance.ro IpAddress .1.3.6.1.4.1.727.7.2.15.16.1.4 |
ospfTraps OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.15.16.2 |
ospfVirtIfStateChangeAn ospfIfStateChange trap signifies that there
has been a change in the state of an OSPF vir-
tual interface.
This trap should be generated when the inter-
face state regresses (e.g., goes from Point-
to-Point to Down) or progresses to a terminal
state (i.e., Point-to-Point). NOTIFICATION-TYPE .1.3.6.1.4.1.727.7.2.15.16.2.1 |
ospfNbrStateChangeAn ospfNbrStateChange trap signifies that
there has been a change in the state of a non-
virtual OSPF neighbor. This trap should be
generated when the neighbor state regresses
(e.g., goes from Attempt or Full to 1-Way or
Down) or progresses to a terminal state (e.g.,
2-Way or Full). When an neighbor transitions
from or to Full on non-broadcast multi-access
and broadcast networks, the trap should be gen-
erated by the designated router. A designated
router transitioning to Down will be noted by
ospfIfStateChange. NOTIFICATION-TYPE .1.3.6.1.4.1.727.7.2.15.16.2.2 |
ospfVirtNbrStateChangeAn ospfIfStateChange trap signifies that there
has been a change in the state of an OSPF vir-
tual neighbor. This trap should be generated
when the neighbor state regresses (e.g., goes
from Attempt or Full to 1-Way or Down) or
progresses to a terminal state (e.g., Full). NOTIFICATION-TYPE .1.3.6.1.4.1.727.7.2.15.16.2.3 |
ospfIfConfigErrorAn ospfIfConfigError trap signifies that a
packet has been received on a non-virtual in-
terface from a router whose configuration
parameters conflict with this router's confi-
guration parameters. Note that the event op-
tionMismatch should cause a trap only if it
prevents an adjacency from forming. NOTIFICATION-TYPE .1.3.6.1.4.1.727.7.2.15.16.2.4 |
ospfVirtIfConfigErrorAn ospfConfigError trap signifies that a pack-
et has been received on a virtual interface
from a router whose configuration parameters
conflict with this router's configuration
parameters. Note that the event optionMismatch
should cause a trap only if it prevents an ad-
jacency from forming. NOTIFICATION-TYPE .1.3.6.1.4.1.727.7.2.15.16.2.5 |
ospfIfAuthFailureAn ospfIfAuthFailure trap signifies that a
packet has been received on a non-virtual in-
terface from a router whose authentication key
or authentication type conflicts with this
router's authentication key or authentication
type. NOTIFICATION-TYPE .1.3.6.1.4.1.727.7.2.15.16.2.6 |
ospfVirtIfAuthFailureAn ospfVirtIfAuthFailure trap signifies that a
packet has been received on a virtual interface
from a router whose authentication key or au-
thentication type conflicts with this router's
authentication key or authentication type. NOTIFICATION-TYPE .1.3.6.1.4.1.727.7.2.15.16.2.7 |
ospfIfStateChangeAn ospfIfStateChange trap signifies that there
has been a change in the state of a non-virtual
OSPF interface. This trap should be generated
when the interface state regresses (e.g., goes
from Dr to Down) or progresses to a terminal
state (i.e., Point-to-Point, DR Other, Dr, or
Backup). NOTIFICATION-TYPE .1.3.6.1.4.1.727.7.2.15.16.2.16 |
ospfTrapConformance OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.15.16.3 |
ospfTrapGroups OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.15.16.3.1 |
ospfTrapCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.15.16.3.2 |
More MIBs from Presticom
Browse all PresticomMIBs →SNMP MIB module
Standard SNMP MIB module defining data structures for CLEARTRAC7-MIB.
SNMP MIB module
The APPN-MIB provides standardized SNMP objects to monitor and manage Advanced Peer-to-Peer Networking (APPN) instances on network devices, specifically tracking high-level topology elements such as network nodes, logical links, and session states. It enables administrators to observe APPN-specific performance metrics including node availability, link utilization, and the status of dynamic routing tables within the SNA over TCP/IP or native SNA environments.
The APPC-MIB facilitates the monitoring and management of IBM Systems Network Architecture (SNA) Advanced Program-to-Program Communication (APPC) sessions and logical units on network devices. It exposes specific metrics including session states, connection establishment failures, and resource utilization counters to enable troubleshooting of legacy SNA over IP or TCP/IP transport layers.
Standard SNMP MIB module defining data structures for APPLETALK-MIB.