Home/Catalog/OPTICSIM-RADIO-TRS-COMMON-MIB

OPTICSIM-RADIO-TRS-COMMON-MIB

AI MIB Summary

The OPTICSIM-RADIO-TRS-COMMON-MIB provides SNMP management capabilities for Radio Common SDH/PDH transmission equipment, specifically monitoring physical layer performance metrics such as signal quality, error counts, and interface status for synchronous and plesiochronous digital hierarchy links.

Radio Common SDH/PDH Transmission MIB.
Main OID:
opticsIMRadioTrsCommonMib.1.3.6.1.4.1.637.54.1.10.1
238
Objects
Active
Status
8
Dependencies

Imported Objects

SNMPv2-SMI
SNMPv2-TC
IF-MIB
SNMPv2-CONF
TSDIM-SUPPORT-MIB
OPTICSIM-RADIOREG-MIB
OPTICSIM-COMMON-TC
OPTICSIM-RADIO-TRS-PDH-MIB

Objects

238 total
Object Name
opticsIMRadioTrsCommonMibRadio Common SDH/PDH Transmission MIB.
MODULE-IDENTITY
.1.3.6.1.4.1.637.54.1.10.1
opticsIMRadioTrsCommonMibObject
OBJECT IDENTIFIER
.1.3.6.1.4.1.637.54.1.10.1.1
opticsIMRadioFrequencyTableThis table contains information used to manage the radio frequency.
SEQUENCE OF OpticsIMRadioFrequencyEntry
.1.3.6.1.4.1.637.54.1.10.1.1.1
opticsIMRadioFrequencyEntryAn entry of the opticsIMRadioFrequencyTable table. Each entry corresponds to a Radio Synchronous or Plesiochronous Physical Interface (RSPI or RPPI).
OpticsIMRadioFrequencyEntry
.1.3.6.1.4.1.637.54.1.10.1.1.1.1
radioTxFrequencyThis object specifies the transmission radio frequency. This value must be included in the allowed tx local range (defined by the associated objects MinTxFrequency and MaxTxFrequency) and it is expressed in KHz.rw
Unsigned32
.1.3.6.1.4.1.637.54.1.10.1.1.1.1.1
radioRxFrequencyThis object specifies the receive radio frequency. This value is expressed in KHz. The rx frequency is updated by the physical machine as a side effect of the change of the transmit value according to an algorithm equipment dependent.rw
Unsigned32
.1.3.6.1.4.1.637.54.1.10.1.1.1.1.2
radioMinTxFrequencyThis object specifies the minimum value allowed for the transmission frequency. This value is expressed in KHz.rw
Unsigned32
.1.3.6.1.4.1.637.54.1.10.1.1.1.1.3
radioMaxTxFrequencyThis object specifies the maximum value allowed for the transmission frequency. This value is expressed in KHz.rw
Unsigned32
.1.3.6.1.4.1.637.54.1.10.1.1.1.1.4
radioMinRxFrequencyThis object specifies the minimum value allowed for the receive frequency. This value is expressed in KHz.rw
Unsigned32
.1.3.6.1.4.1.637.54.1.10.1.1.1.1.5
radioMaxRxFrequencyThis object specifies the maximum value allowed for the receive frequency. This value is expressed in KHz.rw
Unsigned32
.1.3.6.1.4.1.637.54.1.10.1.1.1.1.6
radioReturnCodeFrequencyThis object is used to discriminate the reason of failure on setting rx and tx frequency: setNoError: the set operation on tx and rx frequency was successful; setHWProblem: generic hardware problems (tx and rx frequency are not supported by HW); setCrossProblem: the tx and rx frequency values, specified in set request, invert your relation respect to actual values (if before set request txFreq > rxFreq, in the set request txFreq < rxFreq, or vice-versa); setDistProblem: problems related to the distance (spacing fail) between the tx and rx frequency values; setNoUPDDisabled: frequency change time-out expirationro
Enumeration
.1.3.6.1.4.1.637.54.1.10.1.1.1.1.7
radioFreqShifterIdThis object specifies the identifier of the shifter requested by the managing systems. The identifier must be included in one of entries of the opticsIMAllowedShifterTable if updated by managing system: in this case as a side effect of setting this object, the agent must set the radioFreqShifterValue, radioMinTxFrequency, radioMaxTxFrequency, radioMinRxFrequency and radioMaxRxFrequency objects with the associated values on opticsIMAllowedShifterTable (allowedShifterValue, allowedShifterMinTxFrequency, allowedShifterMaxTxFrequency, allowedShifterMinRxFrequency allowedShifterMaxRxFrequency ). Otherwise the '-1' value means that the radioShifterValue, radioMinTxFrequency, radioMaxTxFrequency, radioMinRxFrequency and radioMaxRxFrequency objects are set directly by managing systemrw
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.1.1.8
radioFreqShifterValueThis object contains the shifter value requested by the managing systems. It is updated or by the agent when the radioShifterId object is set by the managing systems or directly by the managing system (in this case the agent must set the radioShifterId to '-1' value).rw
Unsigned32
.1.3.6.1.4.1.637.54.1.10.1.1.1.1.9
radioFreqShifterMinTxFrequencyThis object specifies the minimum value allowed for the transmission frequency related to the shifter value. This value is expressed in KHz. It is updated or by the agent when the radioShifterId object is set by the managing systems or directly by the managing system (in this case the agent must set the radioShifterId to '-1' valuerw
Unsigned32
.1.3.6.1.4.1.637.54.1.10.1.1.1.1.10
radioFreqShifterMaxTxFrequencyThis object specifies the maximum value allowed for the transmission frequency related to the shifter value. This value is expressed in KHz. It is updated or by the agent when the radioShifterId object is set by the managing systems or directly by the managing system (in this case the agent must set the radioShifterId to '-1' valuerw
Unsigned32
.1.3.6.1.4.1.637.54.1.10.1.1.1.1.11
radioFreqShifterMinRxFrequencyThis object specifies the minimum value allowed for the receive frequency related to the shifter value. This value is expressed in KHz. It is updated by the agent when the radioShifterId object is set.rw
Unsigned32
.1.3.6.1.4.1.637.54.1.10.1.1.1.1.12
radioFreqShifterMaxRxFrequencyThis object specifies the maximum value allowed for the receive frequency related to the shifter value. This value is expressed in KHz. It is updated by the agent when the radioShifterId object is set.rw
Unsigned32
.1.3.6.1.4.1.637.54.1.10.1.1.1.1.13
opticsIMRadioPowerMngt
OBJECT IDENTIFIER
.1.3.6.1.4.1.637.54.1.10.1.1.2
opticsIMRadioTxPowerTableThis table contains information used to manage the transmitted power (included the ATPC management).
SEQUENCE OF OpticsIMRadioTxPowerEntry
.1.3.6.1.4.1.637.54.1.10.1.1.2.1
opticsIMRadioTxPowerEntryAn entry of the opticsIMRadioTxPowerTable table. Each entry corresponds to a Radio Synchronous or Plesiochronous Physical Interface (RSPI or RPPI).
OpticsIMRadioTxPowerEntry
.1.3.6.1.4.1.637.54.1.10.1.1.2.1.1
radioAtpcEnabledThis object specifies whether the ATPC device is currently allowed to work or not. The true value indicates that the ATPC device is allowed to work and the false value that the device is not allowed to work (transmit power has a fixed value). This object is significant only if ATPC device is implemented.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.10.1.1.2.1.1.1
radioMaxAtpcTxPowerThis object specifies the maximum power level to which the equipment is configured to transmit when the ATPC device is allowed to work. According to the product, this value must be less than (or equal to) associated maxTxPower or maxAllowedAtpcTxPower. It is an integer with associated measure unit expressed in decade of dBm (e.g. 255 means 25.5 dBm).rw
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.1.1.2
radioMinAtpcTxPowerThis object specifies the minimum power level to which the equipment is configured to transmit when the ATPC device is allowed to work. According to the product, this value must be greater than (or equal to) associated minTxPower or minAllowedAtpcTxPower (in this table in case of static modulation setting or in the adaptivrModulationRadioTxPower in case of adaptive modulation setting) . It is an integer with associated measure unit expressed in decade of dBm (e.g. 255 means 25.5 dBm).rw
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.1.1.3
radioAtpcLowPowerThrThis object specifies the power threshold value that has to be compared with the power level received on the remote receiver in order to define the power level to be used by the local transmitter. When the received power level value is less than the one provided in this object the local ATPC device increases the transmitted power but only till the nominal value. This value must be included in the allowed range (defined by the associated AtpcLowPowerMinThr and AtpcLowPowerMaxThr). It is expressed in decade of dBm (e.g. -300 means -30.0 dBm).rw
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.1.1.4
radioAtpcLowPowerMinThrThis object specifies the minimum value allowed for the associated AtpcLowPowerThreshold. It is expressed in decade of dBm.ro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.1.1.5
radioAtpcLowPowerMaxThrThis object specifies the maximum value allowed for the associated AtpcLowPowerThreshold It is expressed in decade of dBm.ro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.1.1.6
radioAtpcExtraLowPowerThrThis object specifies the power threshold value that has to be compared with the power level received on the remote receiver in order to define the power level to be used by the local transmitter. When the received power level value is less than the one provided in this object the local ATPC device increases the transmitted power also over the txNominalPower value. This threshold value is expressed in decade of dBm.ro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.1.1.7
radioCurrentTxPowerThis object specifies the value of the transmitted power when the ATPC function is disabled and the manual operation on transmitted power is not active. It is a integer expressed as decade of dBm (e.g. 255 means 25.5 dBm). This value has to be less than (or equal to) the transmitted nominal power.rw
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.1.1.8
radioTxNominalPowerThis object specifies the value of the transmitted nominal power. This value is an integer expressed as decade of dBm (e.g. 255 means 25.5 dBm).ro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.1.1.9
radioMinTxPowerThis object specifies the minimum value allowed for the transmitted power. This value is an integer expressed as decade of dBm (e.g. 255 means 25.5 dBm).ro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.1.1.10
radioMaxTxPowerThis object specifies the maximum value allowed for the transmitted power. This value is an integer expressed as decade of dBm (e.g. 255 means 25.5 dBm).ro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.1.1.11
radioManOpTxPowerThis object is used to initiate (manOpActive or manOpForItpcActive) or terminate (manOpNotActive) a manual handling of the transmitted power. When a manual handling of the transmitted power is initiated an Abnormal Condition indication is generated. When it is terminated the Abnormal Condition indication is removed. When the manOpActive or manOpForItpcActive value is selected, the manOpTxPowerLevel object is updated with the current value of the transmitted power.rw
Enumeration
.1.3.6.1.4.1.637.54.1.10.1.1.2.1.1.12
radioManOpTxPowerLevelThis object specifies the transmitted power value when a manual operation on transmitted power is active. This value is an integer expressed as decade of dBm (e.g. 255 means 25.5 dBm). Requests to update this object coming from the Far End NE will be accepted only if a manual management of the transmitted power for Intrusive BER is currently active (object manOpTxPower previously updated to manOpForItpcActive value).rw
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.1.1.13
radioMinAllowedAtpcTxPowerThis object specifies the minimum power level allowed for the ATPC device. This value must be greater than (or equal to) the associated minTxPower. It is an integer with associated measure unit expressed in decade of dBm (e.g. 255 means 25.5 dBm).ro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.1.1.14
radioMaxAllowedAtpcTxPowerThis object specifies the maximum power level allowed for the ATPC device. This value must be less than (or equal to) the associated maxTxPower. It is an integer with associated measure unit expressed in decade of dBm (e.g. 255 means 25.5 dBm).ro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.1.1.15
radioDrivingRSLThis object is used to indicate in case of 1+1HSB radio configurations which RSL (Remote Signal Level) of the two remote receivers has to be used in the ATPC algorithm. In all the other configurations this parameter is not significant and has to be set to 'notRelevant' value.rw
Enumeration
.1.3.6.1.4.1.637.54.1.10.1.1.2.1.1.16
radioPowerModeThis object is used to select the power mode on radio interface when both Low and High power modes are supported on the radio interface.rw
Enumeration
.1.3.6.1.4.1.637.54.1.10.1.1.2.1.1.17
radioPowerModeOptionThis object is used to select the power mode option to use on radio interface when different flavour of power ranges are supported by HW radio equipment.rw
Enumeration
.1.3.6.1.4.1.637.54.1.10.1.1.2.1.1.18
radioPowerInsertionLossThis object is used to report the value of the power correction associated to the hw present on Radio equipment.ro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.1.1.19
radioPowerModeOptionAllowedThis object contains the power mode option supported on the radio interface by HW radio equipment.ro
Bits
.1.3.6.1.4.1.637.54.1.10.1.1.2.1.1.20
opticsIMRadioAtpcImplementedThis object specifies whether the ATPC capability is present or not. The true value indicates that the ATPC capability is present and the false value that the capability is not present.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.10.1.1.2.2
opticsIMRadioAtpcDirectionIdThis object specifies the ATPC direction identifier used when all the radio channels transmit in the same direction. The same value is used both for the expected identifier and for the identifier to be sent. If the value '0000' is selected the mismatch detection is disabled.rw
Unsigned32
.1.3.6.1.4.1.637.54.1.10.1.1.2.3
opticsIMIntrusiveTPCTableThis table contains the information related to the management of the Transmitted Power Control (TPC) during an Intrusive BER measurement.
SEQUENCE OF OpticsIMIntrusiveTPCEntry
.1.3.6.1.4.1.637.54.1.10.1.1.2.4
opticsIMIntrusiveTPCEntryAn entry of the opticsIMIntrusiveTPCTable table.
OpticsIMIntrusiveTPCEntry
.1.3.6.1.4.1.637.54.1.10.1.1.2.4.1
intrusiveTPCRadioChannelNumberSee Textual Conventions.ro
OpticsIMRadioChannelNumber (OPTICSIM-COMMON-TC)
.1.3.6.1.4.1.637.54.1.10.1.1.2.4.1.1
intrusiveTPCNearEndMinTxPowerThis object specifies the minimum level of the transmitted power allowed during a BER measurement activated on the corresponding radio channel of the Far End NE. This value is an integer expressed as decade of dBm (e.g. 234 means 23.4 dBm).ro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.4.1.2
intrusiveTPCNearEndMaxTxPowerThis object specifies the maximum level of the transmitted power allowed during a BER measurement activated on the corresponding radio channel of the Far End NE. channel, during an Intrusive BER measurement activated on the Far End NE. This value is an integer expressed as decade of dBm (e.g. 212 means 21.2 dBm).ro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.4.1.3
intrusiveTPCFarEndControlledThis object is used to assume the complete control of the transmitted power of the corresponding Far End radio channel (TRUE value). The Near End, according to a specific strategy product dependent, has to maintain the coherence of the value of this object with the one of the associated object of the Far End NE radio channel (TRUE only if the object manOpTxPower of the radioTTPBidTxPower table assumes the manOpForItpcActive value).rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.10.1.1.2.4.1.4
intrusiveTPCFarEndMinTxPowerThis object specifies the minimum level of the transmitted power allowed on the corresponding Far End radio channel during a BER measurement activated on the Near End NE. It is an integer with associated measure unit expressed in decade of dBm (e.g. 237 means 23.7 dBm).ro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.4.1.5
intrusiveTPCFarEndMaxTxPowerThis object specifies the maximum level of the transmitted power allowed on the corresponding Far End radio channel during a BER measurement activated on the Near End NE. It is an integer with associated measure unit expressed in decade of dBm (e.g. 251 means 25.1 dBm).ro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.4.1.6
intrusiveTPCFarEndManOpTxPowerLevelThis object specifies the transmitted power level used by the corresponding Far End radio channel when an intrusive BER measurement is active. This value is an integer expressed as decade of dBm (e.g. 262 means 26.2 dBm).rw
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.4.1.7
opticsIMRadioATPCHighPowerTableThis table contains information used to manage the ATPC device in high power mode.
SEQUENCE OF OpticsIMRadioATPCHighPowerEntry
.1.3.6.1.4.1.637.54.1.10.1.1.2.5
opticsIMRadioATPCHighPowerEntryAn entry of the opticsIMRadioATPCHighPowerTable table. Each entry corresponds to a Radio Synchronous or Plesiochronous Physical Interface (RSPI or RPPI).
OpticsIMRadioATPCHighPowerEntry
.1.3.6.1.4.1.637.54.1.10.1.1.2.5.1
radioATPCHighPowerModeThis object specifies whether the ATPC device is locked in high-power mode or not. The true value indicates that the ATPC device is locked in high-power mode and the false value that the it is not locked. This object is significant only if ATPC device is implemented and enabled.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.10.1.1.2.5.1.1
radioATPCHighPowerTimeoutThis object indicates that the ATPC device has been in high-power mode for over 5 minutes (true value). This object is significant only if ATPC device is implemented, enabled and is locked in high-power mode.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.10.1.1.2.5.1.2
radioATPCHighPowerTimeoutEnabledThis object specifies whether the ATPC device is currently allowed to work with a timeout. The true value indicates that the ATPC activity in high power mode when both receivers are out of lock is limited to timeout maximum, followed by other time at low power, then high power for 10 seconds each hour until radio path is restored. The false value that the ATPC device is allowed to work without timeout. This object is significant only if ATPC device is implemented and enabledrw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.10.1.1.2.5.1.3
radioATPCLowPowerModeThis object specifies whether the ATPC device is locked in low-power mode or not. The true value indicates that the ATPC device is locked in low-power mode and the false value that the it is not locked. The true value is allowed only if ATPC device is not locked in high-power mode (true value on radioATPCHighPowerMode). This object is significant only if ATPC device is implemented and enabled.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.10.1.1.2.5.1.4
radioATPCLockTimeoutThis object indicates the time period, measured in units of minutes, from the lock on High Power mode (enabled with radioATPCHighPowerMode) or on Low Power mode (enabled with radioATPCLowPowerMode). After this timeout the agent remove the lock on ATPC device. The 0 value is used to have a permanent lock (disabled only by managing system).rw
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.5.1.5
opticsIMAdaptiveModulationRadioTxPowerTableThis table contains information used to manage the transmitted power (included the ATPC management) in case of Adaptive Modulation (adaptiveModulationMode 'true'). The parameters usefull for trasmitted power control not included in this table have to be retrieved from opticsIMRadioTxPowerTable for static modulation setting (adaptiveModulationMode 'false'). For each modulation type supported on adaptive modulation (adaptiveModulationSchemeRange or adaptiveModulationSupported on opticsIMAdaptiveModulationEntry) the managing system has to provide these trasmitted power parameters.
SEQUENCE OF OpticsIMAdaptiveModulationRadioTxPowerEntry
.1.3.6.1.4.1.637.54.1.10.1.1.2.6
opticsIMAdaptiveModulationRadioTxPowerEntryAn entry of the opticsIMAdaptiveModulationRadioTxPowerTable table. Each entry corresponds to a modulation value whithin the Adaptive Modulation process is allowed to work for a Radio Physical Interface. Each entry is created as a side effect of setting of adaptiveModulationSchemeRangeId or adaptiveModulationSupported object (on opticsIMAdaptiveModulationEntry) for each modulation value included in the range.
OpticsIMAdaptiveModulationRadioTxPowerEntry
.1.3.6.1.4.1.637.54.1.10.1.1.2.6.1
adaptiveModulationThis object specifies for which modulation type the transmitter power parameters refer to.
INTEGER
.1.3.6.1.4.1.637.54.1.10.1.1.2.6.1.1
adaptiveModulationRadioMaxAtpcTxPowerThis object specifies the maximum power level to which the equipment is configured to transmit when the ATPC device is allowed to work in case of Adaptive Modulation (adaptiveModulationMode 'true') for the adaptiveModulation value in the index. . According to the product, this value must be less than (or equal to) associated maxTxPower or maxAllowedAtpcTxPower (in adaptive mode). It is an integer with associated measure unit expressed in decade of dBm (e.g. 255 means 25.5 dBm).rw
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.6.1.2
adaptiveModulationRadioMinAllowedAtpcTxPowerThis object specifies the minimum power level allowed for the ATPC device in case of Adaptive Modulation (adaptiveModulationMode 'true') for the adaptiveModulation value in the index. This value must be greater than (or equal to) the associated minTxPower. It is an integer with associated measure unit expressed in decade of dBm (e.g. 255 means 25.5 dBm).ro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.6.1.3
adaptiveModulationRadioMaxAllowedAtpcTxPowerThis object specifies the maximum power level allowed for the ATPC device in case of Adaptive Modulation (adaptiveModulationMode 'true') for the adaptiveModulation value in the index. This value must be less than (or equal to) the associated maxTxPower (in adaptive mode). It is an integer with associated measure unit expressed in decade of dBm (e.g. 255 means 25.5 dBm).ro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.6.1.4
adaptiveModulationRadioCurrentTxPowerThis object specifies the value of the transmitted power when the ATPC function is disabled and the manual operation on transmitted power is not active in case of Adaptive Modulation (adaptiveModulationMode 'true') for the adaptiveModulation value in the index. . It is a integer expressed as decade of dBm (e.g. 255 means 25.5 dBm). This value has to be less than (or equal to) the transmitted nominal power.rw
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.6.1.5
adaptiveModulationRadioMinTxPowerThis object specifies the minimum value allowed for the transmitted power in case of Adaptive Modulation (adaptiveModulationMode 'true') for the adaptiveModulation value in the index. This value is an integer expressed as decade of dBm (e.g. 255 means 25.5 dBm).ro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.6.1.6
adaptiveModulationRadioMaxTxPowerThis object specifies the maximum value allowed for the transmitted power in case of Adaptive Modulation (adaptiveModulationMode 'true') for the adaptiveModulation value in the index. This value is an integer expressed as decade of dBm (e.g. 255 means 25.5 dBm).ro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.6.1.7
opticsIMAllowedPowerCapabilitiesTableThis table contains all the power capabilities for all the modulation schemes supported for a specific radio interface type. For each modulation type supported the managed system has to provide these trasmitted power parameters.
SEQUENCE OF OpticsIMAllowedPowerCapabilitiesEntry
.1.3.6.1.4.1.637.54.1.10.1.1.2.7
opticsIMAllowedPowerCapabilitiesEntryAn entry of the opticsIMAllowedPowerCapabilitiesTable table. Each entry (row) corresponds to the power ranges for RTPC and ATPC mode for each modulation scheme supported on a specific radio interface type.
OpticsIMAllowedPowerCapabilitiesEntry
.1.3.6.1.4.1.637.54.1.10.1.1.2.7.1
opticsIMAllowedPowerRadioTypeIdThis object contains the identifier associated to a radio interface type. It identifies a index of the table. The value for each radio interface type is product dependent and defined in each product specification.
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.7.1.1
opticsIMAllowedPowerModulationThis object specifies for which modulation type the transmitter power ranges refer to.
INTEGER
.1.3.6.1.4.1.637.54.1.10.1.1.2.7.1.2
opticsIMAllowedPowerAtpcLowPowerMinThrThis object specifies the minimum value allowed for the associated Low Power Threshold used in ATPC mode for the opticsIMAllowedPowerModulation value in the index. It is expressed in decade of dBm.ro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.7.1.3
opticsIMAllowedPowerAtpcLowPowerMaxThrThis object specifies the maximum value allowed for the associated Low Power Threshold used in ATPC mode for the opticsIMAllowedPowerModulation value in the index. It is expressed in decade of dBm.ro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.7.1.4
opticsIMAllowedPowerMinTxPowerThis object specifies the minimum value allowed for the transmitted power used in RTPC mode for the opticsIMAllowedPowerModulation value in the index. This value is an integer expressed as decade of dBm (e.g. 255 means 25.5 dBm).ro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.7.1.5
opticsIMAllowedPowerMaxTxPowerThis object specifies the maximum value allowed for the transmitted power used in RTPC mode for the opticsIMAllowedPowerModulation value in the index. This value is an integer expressed as decade of dBm (e.g. 255 means 25.5 dBm).ro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.7.1.6
opticsIMAllowedPowerMinAllowedAtpcTxPowerThis object specifies the minimum power level allowed for the ATPC device for the opticsIMAllowedPowerModulation value in the index. It is an integer with associated measure unit expressed in decade of dBm (e.g. 255 means 25.5 dBm).ro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.7.1.7
opticsIMAllowedPowerMaxAllowedAtpcTxPowerThis object specifies the maximum power level allowed for the ATPC device for the opticsIMAllowedPowerModulation value in the index. It is an integer with associated measure unit expressed in decade of dBm (e.g. 255 means 25.5 dBm).ro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.7.1.8
opticsIMEnhAllowedPowerCapabilitiesTableThis table contains all the power capabilities depending on the channel spacing and modulation schemes supported for a specific radio interface type. For each channel spacing and modulation type supported the managed system has to provide these trasmitted power parameters.
SEQUENCE OF OpticsIMEnhAllowedPowerCapabilitiesEntry
.1.3.6.1.4.1.637.54.1.10.1.1.2.8
opticsIMEnhAllowedPowerCapabilitiesEntryAn entry of the opticsIMEnhAllowedPowerCapabilitiesTable table. Each entry (row) corresponds to the power ranges for RTPC and ATPC mode for each channel spacing and modulation scheme supported on a specific radio interface type.
OpticsIMEnhAllowedPowerCapabilitiesEntry
.1.3.6.1.4.1.637.54.1.10.1.1.2.8.1
opticsIMEnhAllowedPowerRadioTypeIdThis object contains the identifier associated to a radio interface type. It identifies a index of the table. The value for each radio interface type is product dependent and defined in each product specification.
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.8.1.1
opticsIMEnhAllowedPowerChannelSpacingThis object specifies for which channel spacing the transmitter power ranges refer to.
INTEGER
.1.3.6.1.4.1.637.54.1.10.1.1.2.8.1.2
opticsIMEnhAllowedPowerModulationThis object specifies for which modulation type the transmitter power ranges refer to.
INTEGER
.1.3.6.1.4.1.637.54.1.10.1.1.2.8.1.3
opticsIMEnhAllowedPowerAtpcLowPowerMinThrThis object specifies the minimum value allowed for the associated Low Power Threshold used in ATPC mode for the opticsIMEnhAllowedPowerModulation value in the index. It is expressed in decade of dBm.ro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.8.1.4
opticsIMEnhAllowedPowerAtpcLowPowerMaxThrThis object specifies the maximum value allowed for the associated Low Power Threshold used in ATPC mode for the opticsIMEnhAllowedPowerModulation value in the index. It is expressed in decade of dBm.ro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.8.1.5
opticsIMEnhAllowedPowerMinTxPowerThis object specifies the minimum value allowed for the transmitted power used in RTPC mode for the opticsIMEnhAllowedPowerModulation value in the index. This value is an integer expressed as decade of dBm (e.g. 255 means 25.5 dBm).ro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.8.1.6
opticsIMEnhAllowedPowerMaxTxPowerThis object specifies the maximum value allowed for the transmitted power used in RTPC mode for the opticsIMEnhAllowedPowerModulation value in the index. This value is an integer expressed as decade of dBm (e.g. 255 means 25.5 dBm).ro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.8.1.7
opticsIMEnhAllowedPowerMinAllowedAtpcTxPowerThis object specifies the minimum power level allowed for the ATPC device for the opticsIMEnhAllowedPowerModulation value in the index. It is an integer with associated measure unit expressed in decade of dBm (e.g. 255 means 25.5 dBm).ro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.8.1.8
opticsIMEnhAllowedPowerMaxAllowedAtpcTxPowerThis object specifies the maximum power level allowed for the ATPC device for the opticsIMEnhAllowedPowerModulation value in the index. It is an integer with associated measure unit expressed in decade of dBm (e.g. 255 means 25.5 dBm).ro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.8.1.9
opticsIMEnhAllowedHighPowerAtpcLowPowerMinThrThis object specifies the minimum value allowed in High Power mode for the associated Low Power Threshold used in ATPC mode for the opticsIMEnhAllowedPowerModulation value in the index . It is expressed in decade of dBm.ro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.8.1.10
opticsIMEnhAllowedHighPowerAtpcLowPowerMaxThrThis object specifies the maximum value allowed in High Power mode for the associated Low Power Threshold used in ATPC mode for the opticsIMEnhAllowedPowerModulation value in the index. It is expressed in decade of dBm.ro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.8.1.11
opticsIMEnhAllowedHighPowerMinTxPowerThis object specifies the minimum value allowed in High Power mode for the transmitted power used in RTPC mode for the opticsIMEnhAllowedPowerModulation value in the index. This value is an integer expressed as decade of dBm (e.g. 255 means 25.5 dBm).ro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.8.1.12
opticsIMEnhAllowedHighPowerMaxTxPowerThis object specifies the maximum value allowed in High Power mode for the transmitted power used in RTPC mode for the opticsIMEnhAllowedPowerModulation value in the index. This value is an integer expressed as decade of dBm (e.g. 255 means 25.5 dBm).ro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.8.1.13
opticsIMEnhAllowedHighPowerMinAllowedAtpcTxPowerThis object specifies the minimum power level allowed in High Power mode for the ATPC device for the opticsIMEnhAllowedPowerModulation value in the index. It is an integer with associated measure unit expressed in decade of dBm (e.g. 255 means 25.5 dBm).ro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.8.1.14
opticsIMEnhAllowedHighPowerMaxAllowedAtpcTxPowerThis object specifies the maximum power level allowed in High Power mode for the ATPC device for the opticsIMEnhAllowedPowerModulation value in the index. It is an integer with associated measure unit expressed in decade of dBm (e.g. 255 means 25.5 dBm).ro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.2.8.1.15
opticsIMRadioRxGainTableThis table contains information used to manage the Rx gain.
SEQUENCE OF OpticsIMRadioRxGainEntry
.1.3.6.1.4.1.637.54.1.10.1.1.3
opticsIMRadioRxGainEntryAn entry of the opticsIMRadioRxGainTable table. Each entry corresponds to a Radio Synchronous or Plesiochronous Physical Interface (RSPI or RPPI).
OpticsIMRadioRxGainEntry
.1.3.6.1.4.1.637.54.1.10.1.1.3.1
radioManOpRxGainThis object is used to initiate (manOpActive) or terminate (manOpNotActive) a manual handling of the gain level. When the manOpActive value is selected an Abnormal Condition indication is generated. When the manOpNotActive value is selected the Abnormal Condition indication is removed. When the manOpActive value is selected, the associated value is contained in the object ManOpRxGainLevel and, but only in case of Space Diversity configuration, in the object ManOpRxDivGainLevel.rw
Enumeration
.1.3.6.1.4.1.637.54.1.10.1.1.3.1.1
radioManOpRxGainLevelSee Textual Conventions. When the Space Diversity configuration is supported this object refers to the gain level of the main receiver.rw
OpticsIMManOpRxGainLevel
.1.3.6.1.4.1.637.54.1.10.1.1.3.1.2
radioManOpRxDivGainLevelSee Textual Conventions. This gain level refers to the diversity receiver and then it is used only when the Space Diversity configuration is supported.rw
OpticsIMManOpRxGainLevel
.1.3.6.1.4.1.637.54.1.10.1.1.3.1.3
radioMinRxGainThis object specifies the minimum value allowed for the gain level and is expressed in dB.ro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.3.1.4
radioMaxRxGainThis object specifies the maximum value allowed for the gain level and is expressed in dB.ro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.3.1.5
opticsIMRadioAnalogueMeasuresTableThis table contains the radio analogue measurements.
SEQUENCE OF OpticsIMRadioAnalogueMeasuresEntry
.1.3.6.1.4.1.637.54.1.10.1.1.4
opticsIMRadioAnalogueMeasuresEntryAn entry of the analogue measurements table. Each entry corresponds to a Radio Synchronous or Plesiochronous Physical Interface (RSPI or RPPI).
OpticsIMRadioAnalogueMeasuresEntry
.1.3.6.1.4.1.637.54.1.10.1.1.4.1
analogueMeasuresRadioChannelNumberSee Textual Conventions.ro
OpticsIMRadioChannelNumber (OPTICSIM-COMMON-TC)
.1.3.6.1.4.1.637.54.1.10.1.1.4.1.1
analogueMeasuresLocalTxPowerThis object represents the local transmitted power level. It is an integer with associated measure unit expressed in decade of dBm.ro
Integer32 (-1000..1000)
.1.3.6.1.4.1.637.54.1.10.1.1.4.1.2
analogueMeasuresLocalRxMainPowerThis object represents the local received power level. In case of space diversity configuration with combiner function in base band it is used to represent the power at the input of the local main receiver. It is a negative integer with associated measure unit expressed in decade of dBm.ro
Integer32 (-1000..0)
.1.3.6.1.4.1.637.54.1.10.1.1.4.1.3
analogueMeasuresLocalRxDivPowerThis object is used to represent the power at the input of the local diversity receiver in case of space diversity configuration with combiner function in base band. It is a negative integer with associated measure unit expressed in decade of dBm.ro
Integer32 (-1000..0)
.1.3.6.1.4.1.637.54.1.10.1.1.4.1.4
analogueMeasuresRemoteTxPowerThis object represents the remote transmitted power level. It is an integer with associated measure unit expressed in decade of dBm.ro
Integer32 (-1000..1000)
.1.3.6.1.4.1.637.54.1.10.1.1.4.1.6
analogueMeasuresRemoteRxMainPowerThis object represents the remote received power level. In case of space diversity configuration with combiner function in base band it is used to represent the power at the input of the remote main receiver. It is a negative integer with associated measure unit expressed in decade of dBm.ro
Integer32 (-1000..0)
.1.3.6.1.4.1.637.54.1.10.1.1.4.1.7
analogueMeasuresRemoteRxDivPowerThis object is used to represent the power at the input of the remote diversity receiver in case of space diversity configuration with combiner function in base band. It is a negative integer with associated measure unit expressed in decade of dBm.ro
Integer32 (-1000..0)
.1.3.6.1.4.1.637.54.1.10.1.1.4.1.8
analogueMeasuresLocalXpdThis object is used to represent the XPD value. It is a positive integer number with associated measure unit expressed in decade of dBro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.4.1.9
analogueMeasuresRetrievingTimeThis object conatins the time of managed system when the measure is reported to the managing systemro
OpticsIMPmRetrievingTime (OPTICSIM-COMMON-TC)
.1.3.6.1.4.1.637.54.1.10.1.1.4.1.10
analogueMeasuresLocalModulationThis object represents the modulation value as currently used by the local radio interface and reported to the managing system. It could follow the modulation value as provisioned by managing system on Fixed Modulation mode or the one currently used by the system and computed by the Adaptive Modulation process. The 'noModulationValue' is reported in case the modulation value is not available.ro
OpticsIMModulationTypeOrZero (OPTICSIM-RADIO-TRS-PDH-MIB)
.1.3.6.1.4.1.637.54.1.10.1.1.4.1.11
analogueMeasuresRemoteModulationThis object represents the modulation value as currently used by the remote radio interface and reported to the managing system through the local radio interface. It could be the modulation value as provisioned by managing system on Fixed Modulation mode or the one currently used by the remote system and computed by the Adaptive Modulation process. The 'noModulationValue' is reported in case the modulation value is not available.ro
OpticsIMModulationTypeOrZero (OPTICSIM-RADIO-TRS-PDH-MIB)
.1.3.6.1.4.1.637.54.1.10.1.1.4.1.12
analogueMeasuresLocalMSEThis object represents the local MSE value. It is a negative integer with associated measure unit expressed in decade of dB.ro
Integer32 (-1000..0)
.1.3.6.1.4.1.637.54.1.10.1.1.4.1.13
analogueMeasuresRemoteMSEThis object represents the remote MSE value. It is a negative integer with associated measure unit expressed in decade of dB.ro
Integer32 (-1000..0)
.1.3.6.1.4.1.637.54.1.10.1.1.4.1.14
analogueMeasuresLocalTxPowerBranchingLossThis object represents the correction value, provided by the managing system, to be applied to the local transmitted power level due to a loss on branching side. The getting on analogueMeasuresLocalTxPower will reflect this correction value. It is an integer with associated measure unit expressed in tenths of dB(e.g. 150 means 15.0 dB).rw
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.4.1.15
analogueMeasuresLocalRxMainPowerBranchingLossThis object represents the correction value, provided by the managing system, to be applied to the local received level on the main receiver due to a loss on branching side. The getting on analogueMeasuresLocalRxMainPower will reflect this correction value. It is an integer with associated measure unit expressed in tenths of dB (e.g. 150 means 15.0 dB).rw
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.4.1.16
analogueMeasuresLocalRxDivPowerBranchingLossThis object represents the correction value, provided by the managing system, to be applied to the local received level on the diversity receiver due to a loss on branching side. The getting on analogueMeasuresLocalRxDivPower will reflect this correction value. It is an integer with associated measure unit expressed in tenths of dB (e.g. 150 means 15.0 dB).rw
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.4.1.17
analogueMeasuresRemoteXpdThis object is used to represent the remote XPD value. It is a positive integer number with associated measure unit expressed in decade of dBro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.4.1.18
analogueMeasuresLocalDivXpdThis object is used to represent the local XPD value for Diversity configuration. It is a positive integer number with associated measure unit expressed in decade of dBro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.4.1.19
analogueMeasuresRemoteDivXpdThis object is used to represent the remote XPD value for the Diversity configuration. It is a positive integer number with associated measure unit expressed in decade of dBro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.4.1.20
analogueMeasuresLocalDivMSEThis object is used to represent the local MSE value for Diversity configuration. It is a negative integer with associated measure unit expressed in decade of dB.ro
Integer32 (-1000..0)
.1.3.6.1.4.1.637.54.1.10.1.1.4.1.21
analogueMeasuresRemoteDivMSEThis object is used to represent the remote MSE value for the Diversity configuration. It is a negative integer with associated measure unit expressed in decade of dB.ro
Integer32 (-1000..0)
.1.3.6.1.4.1.637.54.1.10.1.1.4.1.22
opticsIMRadioAlarms
OBJECT IDENTIFIER
.1.3.6.1.4.1.637.54.1.10.1.1.5
opticsIMAlarmAtpcLoopProblemRaiseThis notification reports the ATPC Loop Problem defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.15
opticsIMAlarmAtpcLoopProblemClearThis notification reports the ATPC Loop Problem defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.16
opticsIMAlarmIncompatibleShifterRaiseThis notification reports the incompatibleShifter (a mismatch between shifter provided and shifter supported by HW) defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.17
opticsIMAlarmIncompatibleShifterClearThis notification reports the incompatibleShifter (a mismatch between shifter provided and shifter supported by HW) defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.18
opticsIMAlarmIncompatibleModulationRaiseThis notification reports the incompatibility of modulation value defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.19
opticsIMAlarmIncompatibleModulationClearThis notification reports the incompatibility of modulation value defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.20
opticsIMAlarmBandwidthOverFlowRaiseThis notification reports the overFlow of the bandwidth used over the allowed one defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.21
opticsIMAlarmBandwidthOverFlowClearThis notification reports the overFlow of the bandwidth used over the allowed one defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.22
opticsIMAlarmAtpcIdentifierMismatchRaiseThis notification reports the ATPC Identifier Mismatch defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.23
opticsIMAlarmAtpcIdentifierMismatchClearThis notification reports the ATPC Identifier Mismatch defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.24
opticsIMAlarmRadioChannelIdentifierMismatchRaiseThis notification reports the Radio Channel Identifier Mismatch (RCIM) defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.25
opticsIMAlarmRadioChannelIdentifierMismatchClearThis notification reports the Radio Channel Identifier Mismatch (RCIM) defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.26
opticsIMAlarmIncompatibleFrequencyRaiseThis notification reports the incompatible frequency defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.27
opticsIMAlarmIncompatibleFrequencyClearThis notification reports the incompatible Frequency defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.28
opticsIMAlarmIncompatiblePTXRaiseThis notification reports the incompatible Tx Power defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.29
opticsIMAlarmIncompatiblePTXClearThis notification reports the incompatible Tx Power defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.30
opticsIMAlarmIncompatibleCapacityRaiseThis notification reports the incompatibility of capacity value defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.31
opticsIMAlarmIncompatibleCapacityClearThis notification reports the incompatibility of capacity value defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.32
opticsIMAlarmHighBERRaiseThis notification reports the highBER defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.35
opticsIMAlarmHighBERClearThis notification reports the highBER defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.36
opticsIMAlarmLowBERRaiseThis notification reports the lowBER defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.37
opticsIMAlarmLowBERClearThis notification reports the lowBER defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.38
opticsIMAlarmEarlyWarningRaiseThis notification reports the Early Warning defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.39
opticsIMAlarmEarlyWarningClearThis notification reports the Early Warning defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.40
opticsIMAlarmPathDistortionRaiseThis notification reports the Path Distortion defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.41
opticsIMAlarmPathDistortionClearThis notification reports the Path Distortion defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.42
opticsIMAlarmRadioDADERaiseThis notification reports the Radio Dade defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.43
opticsIMAlarmRadioDADEClearThis notification reports the Radio Dade defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.44
opticsIMAlarmRingBrokeRaiseThis notification reports the Ring Broke defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.45
opticsIMAlarmRingBrokeClearThis notification reports the Ring Broke defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.46
opticsIMAlarmDialogFailureRaiseThis notification reports the Dialog Failure Problem (DF) defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.47
opticsIMAlarmDialogFailureClearThis notification reports the Dialog Failure Problem (DF) defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.48
opticsIMAlarmCrossConnectionFailRaiseThis notification reports the failure of the cross connection configuration (collision on ARL table) raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.49
opticsIMAlarmCrossConnectionFailClearThis notification reports the failure of the cross connection configuration (collision on ARL table) clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.50
opticsIMAlarmRPSPathFailRaiseThis notification reports the RPS path fail (RPS communication problem) defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.51
opticsIMAlarmRPSPathFailClearThis notification reports the the RPS path fail (RPS communication problem) defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.52
opticsIMAlarmLoopProblemRaiseThis notification reports the generic Loop Problem defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.53
opticsIMAlarmLoopProblemClearThis notification reports the generic Loop Problem defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.54
opticsIMAlarmIncompatibleModulationParamRaiseThis notification reports the incompatibility of modulation parameters values defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.55
opticsIMAlarmIncompatibleModulationParamClearThis notification reports the incompatibility of modulation parameters values defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.56
opticsIMAlarmIncompatiblePowerRaiseThis notification reports the incompatibility of the power value defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.57
opticsIMAlarmIncompatiblePowerClearThis notification reports the incompatibility of of the power value defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.58
opticsIMAlarmIncompatibleChannelSpacingRaiseThis notification reports the incompatibility of channel spacing value defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.59
opticsIMAlarmIncompatibleChannelSpacingClearThis notification reports the incompatibility of channel spacing value defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.60
opticsIMAlarmDemDivLOSRaiseThis notification reports the demDivLOS (LOS of the incoming diversity signal for the demodulation subfunction in case of Space Diversity configuration) defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.61
opticsIMAlarmDemDivLOSClearThis notification reports the demDivLOS (LOS of the incoming diversity signal for the demodulation subfunction, in case of Space Diversity configuration) defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.62
opticsIMAlarmRxDivFailRaiseThis notification reports the rxDivFail (a fail of the Rx Diversity subfunction, in case of Space Diversity configuration) defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.63
opticsIMAlarmRxDivFailClearThis notification reports the rxDivFail (a fail of the Rx Diversity subfunction, in case of Space Diversity configuration) defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.64
opticsIMAlarmDemXpicLOSRaiseThis notification reports the rxDivFail (a fail of the Rx Diversity subfunction, in case of Space Diversity configuration) defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.65
opticsIMAlarmDemXpicLOSClearThis notification reports the rxDivFail (a fail of the Rx Diversity subfunction, in case of Space Diversity configuration) defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.66
opticsIMAlarmATPCTimeoutRaiseThis notification reports the ATPC timeout defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.67
opticsIMAlarmATPCTimeoutClearThis notification reports the ATPC timeout defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.68
opticsIMAlarmRadioEncryptionMismatchRaiseThis notification reports the mismatch on the traffic encryption on radio interface defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.69
opticsIMAlarmRadioEncryptionMismatchClearThis notification reports the mismatch on the traffic encryption on radio interface defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.70
opticsIMAlarmRxOverloadRaiseThis notification reports the Rx Overload on radio interface defect raise.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.71
opticsIMAlarmRxOverloadClearThis notification reports the Rx Overload on radio interface defect clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.637.54.1.10.1.1.5.72
opticsIMAnaloguePointsTableThis table allows to provide the status assumed by generic analogue points.
SEQUENCE OF OpticsIMAnaloguePointsEntry
.1.3.6.1.4.1.637.54.1.10.1.1.6
opticsIMAnaloguePointsEntryAn entry of the analogue points table.
OpticsIMAnaloguePointsEntry
.1.3.6.1.4.1.637.54.1.10.1.1.6.1
analoguePointsIndexThis object represents the index of the table.ro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.6.1.1
analoguePointsDescriptionThis object contains the description of the meaning of the value provided by the analoguePointsStatus object.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.10.1.1.6.1.2
analoguePointsStatusThis object is used to provide the status of a analogue point whose meaning is provided by the analoguePointsDescription object.ro
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.6.1.3
opticsIMRadioTxMuteTableThis table contains the information related to the management of the radio TX Mute function (local and remote).
SEQUENCE OF OpticsIMRadioTxMuteEntry
.1.3.6.1.4.1.637.54.1.10.1.1.7
opticsIMRadioTxMuteEntryAn entry of the Radio Tx Mute table. Each entry corresponds to a Radio Synchronous or Plesiochronous Physical Interface (RSPI or RPPI).
OpticsIMRadioTxMuteEntry
.1.3.6.1.4.1.637.54.1.10.1.1.7.1
opticsIMRadioManLocalTxMuteThis object allows to the managers to squelch the local transmitter. When the local transmitter is squelched an Abnormal Condition indication is generated. See Textual Conventions.rw
OpticsIMRadioTxMuteStatus
.1.3.6.1.4.1.637.54.1.10.1.1.7.1.1
opticsIMRadioAutoLocalTxMuteThis object specifies if an automatic squelch of the local transmitter, performed directly by the agent, is currently active. When the local transmitter is squelched an Abnormal Condition indication is generated. See Textual Conventions.ro
OpticsIMRadioTxMuteStatus
.1.3.6.1.4.1.637.54.1.10.1.1.7.1.2
opticsIMRadioManRemoteTxMuteThis object allows to the managers to squelch the remote transmitter. See Textual Conventions.rw
OpticsIMRadioTxMuteStatus
.1.3.6.1.4.1.637.54.1.10.1.1.7.1.3
opticsIMRadioAutoRemoteTxMuteThis object specifies if an automatic squelch of the remote transmitter, performed directly by the agent, is currently active. See Textual Conventions.ro
OpticsIMRadioTxMuteStatus
.1.3.6.1.4.1.637.54.1.10.1.1.7.1.4
opticsIMRadioManLocalActivationDateThis object indicates the date and the time when the the local transmitter has been squelched. It is provided according to the following format: yyy/mm/dd hh:mm:ss. If the loopback has not been yet squelched, then the string notYetActivated is used.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.10.1.1.7.1.5
opticsIMRadioManLocalTimeoutPeriodThis object indicates the time period, measured in units of minutes, from the squelched date (specified on opticsIMRadioManLocalActivationDate object) during the local transmitter is squelched. After this timeout the agent enables the local transmitter ('off' value on opticsIMRadioManLocalTxMute ).rw
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.7.1.6
opticsIMRadioManRemoteActivationDateThis object indicates the date and the time when the the remote transmitter has been squelched. It is provided according to the following format: yyy/mm/dd hh:mm:ss. If the loopback has not been yet squelched, then the string notYetActivated is used.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.10.1.1.7.1.7
opticsIMRadioManRemoteTimeoutPeriodThis object indicates the time period, measured in units of minutes, from the squelched date (specified on opticsIMRadioManRemoteActivationDate object) during the remote transmitter is squelched. After this timeout the agent enables the remote transmitter ('off' value on opticsIMRadioManRemoteTxMute ).rw
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.7.1.8
opticsIMRadioAutoLocalTxMuteRemoteRequestThis object indicates XPIC local mute by remote request(XPIC auto remote tx mute).ro
OpticsIMRadioTxMuteStatus
.1.3.6.1.4.1.637.54.1.10.1.1.7.1.9
opticsIMRadioShifterTableThis table contains the shifter and central frequency values associated to installed equipment.
SEQUENCE OF OpticsIMRadioShifterEntry
.1.3.6.1.4.1.637.54.1.10.1.1.8
opticsIMRadioShifterEntryAn entry of the opticsIMRadioShifterTable table. Each entry corresponds to a shifter and central frequency values for each Radio channel used by the algorithm equipment dependent managing radio frequency.
OpticsIMRadioShifterEntry
.1.3.6.1.4.1.637.54.1.10.1.1.8.1
radioShifterIdThis object specifies the identifier of the set of shifter and central radio frequency requested by the managing systems. The identifier must be included in one of entries of the opticsIMAllowedShifterTable if updated by managing system: in this case as a side effect of setting this object, the agent must set the radioShifterValue and radioShifterCentralFrequency objects with the associated values on opticsIMAllowedShifterTable (allowedShifterValue and allowedShifterCentralFrequency). Otherwise the '-1' value means that the radioShifterValue and radioShifterCentralFrequency objects are set directly by managing systemrw
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.8.1.1
radioShifterValueThis object contains the shifter value requested by the managing systems. It is updated or by the agent when the radioShifterId object is set by the managing systems or directly by the managing system (in this case the agent must set the radioShifterId to '-1' value).rw
Unsigned32
.1.3.6.1.4.1.637.54.1.10.1.1.8.1.2
radioShifterCentralFrequencyThis object specifies the central radio frequency requested by the managing systems. It is updated or by the agent when the radioShifterId object is set by the managing systems or directly by the managing system (in this case the agent must set the radioShifterId to '-1' value). This value is expressed in KHz.rw
Unsigned32
.1.3.6.1.4.1.637.54.1.10.1.1.8.1.3
opticsIMAllowedShifterTableThis table contains the allowed shifter and central frequency values
SEQUENCE OF OpticsIMAllowedShifterEntry
.1.3.6.1.4.1.637.54.1.10.1.1.9
opticsIMAllowedShifterEntryAn entry of the opticsIMAllowedShifterTable table. Each entry corresponds to a set of shifter and central frequency allowed.
OpticsIMAllowedShifterEntry
.1.3.6.1.4.1.637.54.1.10.1.1.9.1
allowedShifterIdThis object contains the index of the table. It identifies the set of shifters. A shifter is identifed by a value and a central frequency or by a value and a min and max Tx frequency.
Integer32
.1.3.6.1.4.1.637.54.1.10.1.1.9.1.1
allowedShifterValueThis object contains the shifter value allowed.ro
Unsigned32
.1.3.6.1.4.1.637.54.1.10.1.1.9.1.2
allowedShifterCentralFrequencyThis object specifies the central frequency value associated to the shifter value. This value is expressed in KHz.ro
Unsigned32
.1.3.6.1.4.1.637.54.1.10.1.1.9.1.3
allowedShifterMinTxFrequencyThis object specifies the minimum value allowed for the transmission frequency associated to the shifter value. This value is expressed in KHz.ro
Unsigned32
.1.3.6.1.4.1.637.54.1.10.1.1.9.1.4
allowedShifterMaxTxFrequencyThis object specifies the maximum value allowed for the transmission frequency associated to the shifter value. This value is expressed in KHz.ro
Unsigned32
.1.3.6.1.4.1.637.54.1.10.1.1.9.1.5
allowedShifterMinRxFrequencyThis object specifies the minimum value allowed for the receive frequency associated to this shifter (identified by the value and min and max Tx frequency). This value is expressed in KHz.ro
Unsigned32
.1.3.6.1.4.1.637.54.1.10.1.1.9.1.6
allowedShifterMaxRxFrequencyThis object specifies the maximum value allowed for the receive frequency associated to this shifter (identified by the value and min and max Tx frequency). This value is expressed in KHz.ro
Unsigned32
.1.3.6.1.4.1.637.54.1.10.1.1.9.1.7
allowedMinTxFrequencyThis object specifies the minimum value allowed for the transmission frequency associated to the shifter and the channel spacing values. This value is expressed in KHz.ro
Unsigned32
.1.3.6.1.4.1.637.54.1.10.1.1.9.1.8
allowedMaxTxFrequencyThis object specifies the maximum value allowed for the transmission frequency associated to the shifter and the channel spacing values. This value is expressed in KHz.ro
Unsigned32
.1.3.6.1.4.1.637.54.1.10.1.1.9.1.9
allowedMinRxFrequencyThis object specifies the minimum value allowed for the receive frequency associated to this shifter (identified by the value and min and max Tx frequency) and the channel spacing value. This value is expressed in KHz.ro
Unsigned32
.1.3.6.1.4.1.637.54.1.10.1.1.9.1.10
allowedMaxRxFrequencyThis object specifies the maximum value allowed for the receive frequency associated to this shifter (identified by the value and min and max Tx frequency)and the channel spacing values. This value is expressed in KHz.ro
Unsigned32
.1.3.6.1.4.1.637.54.1.10.1.1.9.1.11
opticsIMRadioInterferenceMeasuresTableThis table manages the radio interference measurements.
SEQUENCE OF OpticsIMRadioInterferenceMeasuresEntry
.1.3.6.1.4.1.637.54.1.10.1.1.10
opticsIMRadioInterferenceMeasuresEntryAn entry of the opticsIMRadioInterferenceMeasuresTable table. Each entry corresponds to a Radio Synhronous or Plesiochronous Physical Interface (RSPI or RPPI)
OpticsIMRadioInterferenceMeasuresEntry
.1.3.6.1.4.1.637.54.1.10.1.1.10.1
interferenceMeasuresRxPowerFactoryMeasuredTo10E6BerThis object specifies the factory designed rx power level value (in dBm) corresponding to 10-6 BER. It is a negative integer with associated measure unit expressed in decade of dBm.ro
Integer32 (-1000..0)
.1.3.6.1.4.1.637.54.1.10.1.1.10.1.1
interferenceMeasuresRowStatusSee textual conventions.rw
RowStatus (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.10.1.1.10.1.2
opticsIMRadioTrsCommonMCConf
OBJECT IDENTIFIER
.1.3.6.1.4.1.637.54.1.10.99.1
opticsIMRadioTrsCommonMCCompl
OBJECT IDENTIFIER
.1.3.6.1.4.1.637.54.1.10.99.1.1
opticsIMRadioTrsCommonMcThis module compliance describes a set of objects required for Optics-IM Agent implementation. These objects are defined inside opticsIMRadioTrsCommonMib.
Unknown
.1.3.6.1.4.1.637.54.1.10.99.1.1.1
opticsIMRadioTrsCommonMCGroup
OBJECT IDENTIFIER
.1.3.6.1.4.1.637.54.1.10.99.1.2
opticsIMRadioFrequencyGroupThis group describes the mandatory objects related to the management of the radio frequency.
Unknown
.1.3.6.1.4.1.637.54.1.10.99.1.2.1
opticsIMRadioTxPowerGroupThis group describes the mandatory objects related to the management of the radio tx power.
Unknown
.1.3.6.1.4.1.637.54.1.10.99.1.2.2
opticsIMOptRadioRxGainGroupThis group describes the optional objects related to the radio rx gain management.
Unknown
.1.3.6.1.4.1.637.54.1.10.99.1.2.3
opticsIMRadioAnalogueMeasuresGroupThis group describes the mandatory objects related to the reporting of the radio analogue measures.
Unknown
.1.3.6.1.4.1.637.54.1.10.99.1.2.4
opticsIMRadioCommonAlarmsGroupThis group describes the Radio alarms notifications.
Unknown
.1.3.6.1.4.1.637.54.1.10.99.1.2.6
opticsIMOptRadioPowerGroupThis group describes the optional objects related to the management of the radio tx power.
Unknown
.1.3.6.1.4.1.637.54.1.10.99.1.2.7
opticsIMOptIntrusiveTPCGroupThis group describes the optional objects related to the management of the radio Intrusive Transmitted Power Control management.
Unknown
.1.3.6.1.4.1.637.54.1.10.99.1.2.8
opticsIMRadioTxMuteGroupThis group describes the objects related to the management of the radio Tx Mute function.
Unknown
.1.3.6.1.4.1.637.54.1.10.99.1.2.9
opticsIMRadioOptAlarmsGroupThis group describes the Radio optional alarms notifications.
Unknown
.1.3.6.1.4.1.637.54.1.10.99.1.2.10
opticsIMAnaloguePointsGroupThis group describes the objects related to the management of the analogue points.
Unknown
.1.3.6.1.4.1.637.54.1.10.99.1.2.11
opticsIMOptRadioATPCHighPowerGroupThis group describes the objects related to the ATPC management in high-power mode.
Unknown
.1.3.6.1.4.1.637.54.1.10.99.1.2.12
opticsIMOptRadioFrequencyGroupThis group describes optional objects related to the management of the receive radio frequency.
Unknown
.1.3.6.1.4.1.637.54.1.10.99.1.2.13
opticsIMOptRadioReturnCodeFrequencyGroupThis group describes optional objects related to the management of the return code on setting radio frequency.
Unknown
.1.3.6.1.4.1.637.54.1.10.99.1.2.14
opticsIMOptRadioShifterGroupThis group describes optional objects related to the management of shifter related to radio frequency.
Unknown
.1.3.6.1.4.1.637.54.1.10.99.1.2.15
opticsIMOptRadioInterferenceMeasuresGroupThis group describes optional objects related to the management of Radio Interference Measures.
Unknown
.1.3.6.1.4.1.637.54.1.10.99.1.2.16
OPTICSIM-RADIO-TRS-COMMON-MIB - SNMP MIB Reference | MIBs Explorer