Nortel-MsCarrier-MscPassport-FrameRelayNniMIB
AI MIB Summary
Standard SNMP MIB module defining data structures for Nortel-MsCarrier-MscPassport-FrameRelayNniMIB.
711
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
711 total| Object Name |
|---|
mscFrNni OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.1.70 |
mscFrNniRowStatusTableThis entry controls the addition and deletion of
mscFrNni components. SEQUENCE OF MscFrNniRowStatusEntry .1.3.6.1.4.1.562.36.2.1.70.1 |
mscFrNniRowStatusEntryA single entry in the table represents a single
mscFrNni component. MscFrNniRowStatusEntry .1.3.6.1.4.1.562.36.2.1.70.1.1 |
mscFrNniRowStatusThis variable is used as the basis for SNMP naming of
mscFrNni components.
These components can be added and deleted.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.1.1.1 |
mscFrNniComponentNameThis variable provides the component's string name for
use with the ASCII Console Interfacero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.1.1.2 |
mscFrNniStorageTypeThis variable represents the storage type value for the
mscFrNni tables.ro StorageType (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.1.1.4 |
mscFrNniIndexThis variable represents the index for the mscFrNni tables. Integer32 .1.3.6.1.4.1.562.36.2.1.70.1.1.10 |
mscFrNniDna OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.1.70.2 |
mscFrNniDnaRowStatusTableThis entry controls the addition and deletion of
mscFrNniDna components. SEQUENCE OF MscFrNniDnaRowStatusEntry .1.3.6.1.4.1.562.36.2.1.70.2.1 |
mscFrNniDnaRowStatusEntryA single entry in the table represents a single
mscFrNniDna component. MscFrNniDnaRowStatusEntry .1.3.6.1.4.1.562.36.2.1.70.2.1.1 |
mscFrNniDnaRowStatusThis variable is used as the basis for SNMP naming of
mscFrNniDna components.
These components cannot be added nor deleted.ro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.2.1.1.1 |
mscFrNniDnaComponentNameThis variable provides the component's string name for
use with the ASCII Console Interfacero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.2.1.1.2 |
mscFrNniDnaStorageTypeThis variable represents the storage type value for the
mscFrNniDna tables.ro StorageType (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.2.1.1.4 |
mscFrNniDnaIndexThis variable represents the index for the mscFrNniDna tables. NonReplicated .1.3.6.1.4.1.562.36.2.1.70.2.1.1.10 |
mscFrNniDnaCug OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.1.70.2.2 |
mscFrNniDnaCugRowStatusTableThis entry controls the addition and deletion of
mscFrNniDnaCug components.obsolete SEQUENCE OF MscFrNniDnaCugRowStatusEntry .1.3.6.1.4.1.562.36.2.1.70.2.2.1 |
mscFrNniDnaCugRowStatusEntryA single entry in the table represents a single
mscFrNniDnaCug component.obsolete MscFrNniDnaCugRowStatusEntry .1.3.6.1.4.1.562.36.2.1.70.2.2.1.1 |
mscFrNniDnaCugRowStatusThis variable is used as the basis for SNMP naming of
mscFrNniDnaCug components.
These components can be added and deleted.rwobsolete RowStatus (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.2.2.1.1.1 |
mscFrNniDnaCugComponentNameThis variable provides the component's string name for
use with the ASCII Console Interfaceroobsolete DisplayString (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.2.2.1.1.2 |
mscFrNniDnaCugStorageTypeThis variable represents the storage type value for the
mscFrNniDnaCug tables.roobsolete StorageType (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.2.2.1.1.4 |
mscFrNniDnaCugIndexThis variable represents the index for the mscFrNniDnaCug tables.obsolete Integer32 .1.3.6.1.4.1.562.36.2.1.70.2.2.1.1.10 |
mscFrNniDnaCugCugOptionsTableAttributes in this group define ClosedUserGroup options associated
with interlockCode. DNA's with the same CUG (interlockCode) can
make calls within this group. Various combinations which permit or
prevent calls in the same CUG group are defined here.obsolete SEQUENCE OF MscFrNniDnaCugCugOptionsEntry .1.3.6.1.4.1.562.36.2.1.70.2.2.10 |
mscFrNniDnaCugCugOptionsEntryAn entry in the mscFrNniDnaCugCugOptionsTable.obsolete MscFrNniDnaCugCugOptionsEntry .1.3.6.1.4.1.562.36.2.1.70.2.2.10.1 |
mscFrNniDnaCugTypeThis attribute specifies the CUG type - the CUG is either a national
CUG, or an international CUG. International closed user groups are
usually established between DTEs for which there is an X.75
Gateway between; whereas national closed user groups are usually
established between DTEs for which there is no X.75 Gateway
between. (National CUGs cannot normally traverse an X.75
Gateway).
If this attribute is set to national, then the CUG is a national CUG,
in which case, the dnic should be left at its default value since it is
not part of a national CUG. If this attribute is set to international,
then the CUG is an international CUG, in which case, the dnic
should be set appropriately as part of the CUG interlockCode.rwobsolete Enumeration .1.3.6.1.4.1.562.36.2.1.70.2.2.10.1.1 |
mscFrNniDnaCugDnicThis attribute specifies the dnic (Data Network ID Code) of the
CUG by which packet networks are identified. This attribute is not
applicable if the CUG is a national CUG, as specified by the CUG
type attribute. There are usually 1 or 2 dnics assigned per country,
for public networks. The U.S. is an exception where each BOC has
a dnic. Also, a group of private networks can have its own dnic.
dnic value is not an arbitrary number. It is assigned by international
agreement and controlled by CCITT.rwobsolete DigitString .1.3.6.1.4.1.562.36.2.1.70.2.2.10.1.2 |
mscFrNniDnaCugInterlockCodeThis attribute specifies the CUG identifier of a national or
international CUG call. It is an arbitrary number and it also can be
called CUG in some descriptions. Interfaces (DNA's) defined with
this number can make calls to DNA's with the same interlockCode.rwobsolete Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.2.2.10.1.3 |
mscFrNniDnaCugPreferentialThe attribute 'preferential', if set to yes indicates that this CUG is
the SIMPLE CUG (as defined in ITU X.36 [10/96]), in which case
it will be used during the call establishment phase if the DTE has
not explicitly specified a CUG index in the call request packet. If set
to no, then this CUG is not the SIMPLE CUG, but an instance of
the SELECTABLE CUG.
The attribute 'preferential' is set to no by CAS when a CUG
instance is created. If only one CUG instance exists under a DNA,
and if this CUG's attributes 'incCalls' and 'outCall' are both set to
allowed, then this CUG instance can be changed to a SIMPLE CUG
by setting the attribute 'preferential' to yes. If more than one CUG
instances exist under a DNA, none of the CUGs can be set by the
user as 'preferential'. Essentially, the attribute 'preferential'
distinguishes a SIMPLE CUG from a SELECTABLE CUG.
In the case of a FRUNI DNA with a single CUG instance, the CUG
can be a SIMPLE CUG (preferential = yes) or the only instance of a
SELECTABLE CUG (preferential = no).rwobsolete Enumeration .1.3.6.1.4.1.562.36.2.1.70.2.2.10.1.4 |
mscFrNniDnaCugOutCallsThis attribute, if set to allowed indicates that outgoing calls (from
the DTE into the network) can be made using this particular CUG.
If set to a value of disallowed, then outgoing calls cannot be made
using this CUG - such calls will be cleared by the local DCE.
This attribute corresponds to the CCITT 'Outgoing Calls Barred'
feature for CUGs in that outgoing calls are barred if this attribute is
set to a value of disallowed.rwobsolete Enumeration .1.3.6.1.4.1.562.36.2.1.70.2.2.10.1.5 |
mscFrNniDnaCugIncCallsThis attribute, if set to allowed indicates that incoming calls (from
the network to the DTE) can be made using this particular CUG. If
set to disallowed, then incoming calls cannot be made using this
CUG - such calls will be cleared by the local DCE.
This attribute corresponds to the CCITT 'Incoming Calls Barred'
feature for CUGs in that incoming calls are barred if this attribute is
set to a value of disallowed.rwobsolete Enumeration .1.3.6.1.4.1.562.36.2.1.70.2.2.10.1.6 |
mscFrNniDnaHgM OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.1.70.2.3 |
mscFrNniDnaHgMRowStatusTableThis entry controls the addition and deletion of
mscFrNniDnaHgM components. SEQUENCE OF MscFrNniDnaHgMRowStatusEntry .1.3.6.1.4.1.562.36.2.1.70.2.3.1 |
mscFrNniDnaHgMRowStatusEntryA single entry in the table represents a single
mscFrNniDnaHgM component. MscFrNniDnaHgMRowStatusEntry .1.3.6.1.4.1.562.36.2.1.70.2.3.1.1 |
mscFrNniDnaHgMRowStatusThis variable is used as the basis for SNMP naming of
mscFrNniDnaHgM components.
These components can be added and deleted.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.2.3.1.1.1 |
mscFrNniDnaHgMComponentNameThis variable provides the component's string name for
use with the ASCII Console Interfacero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.2.3.1.1.2 |
mscFrNniDnaHgMStorageTypeThis variable represents the storage type value for the
mscFrNniDnaHgM tables.ro StorageType (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.2.3.1.1.4 |
mscFrNniDnaHgMIndexThis variable represents the index for the mscFrNniDnaHgM tables. NonReplicated .1.3.6.1.4.1.562.36.2.1.70.2.3.1.1.10 |
mscFrNniDnaHgMHgAddr OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.1.70.2.3.2 |
mscFrNniDnaHgMHgAddrRowStatusTableThis entry controls the addition and deletion of
mscFrNniDnaHgMHgAddr components. SEQUENCE OF MscFrNniDnaHgMHgAddrRowStatusEntry .1.3.6.1.4.1.562.36.2.1.70.2.3.2.1 |
mscFrNniDnaHgMHgAddrRowStatusEntryA single entry in the table represents a single
mscFrNniDnaHgMHgAddr component. MscFrNniDnaHgMHgAddrRowStatusEntry .1.3.6.1.4.1.562.36.2.1.70.2.3.2.1.1 |
mscFrNniDnaHgMHgAddrRowStatusThis variable is used as the basis for SNMP naming of
mscFrNniDnaHgMHgAddr components.
These components can be added and deleted.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.2.3.2.1.1.1 |
mscFrNniDnaHgMHgAddrComponentNameThis variable provides the component's string name for
use with the ASCII Console Interfacero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.2.3.2.1.1.2 |
mscFrNniDnaHgMHgAddrStorageTypeThis variable represents the storage type value for the
mscFrNniDnaHgMHgAddr tables.ro StorageType (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.2.3.2.1.1.4 |
mscFrNniDnaHgMHgAddrIndexThis variable represents the index for the mscFrNniDnaHgMHgAddr tables. Integer32 .1.3.6.1.4.1.562.36.2.1.70.2.3.2.1.1.10 |
mscFrNniDnaHgMHgAddrAddrTableThis group contains attributes common to all DNAs. Every DNA
used in the network is defined with this group of 2 attributes. SEQUENCE OF MscFrNniDnaHgMHgAddrAddrEntry .1.3.6.1.4.1.562.36.2.1.70.2.3.2.10 |
mscFrNniDnaHgMHgAddrAddrEntryAn entry in the mscFrNniDnaHgMHgAddrAddrTable. MscFrNniDnaHgMHgAddrAddrEntry .1.3.6.1.4.1.562.36.2.1.70.2.3.2.10.1 |
mscFrNniDnaHgMHgAddrNumberingPlanIndicatorThis attribute indicates the Numbering Plan Indicator (NPI) of the
DNA. The address may belong to X.121 or E.164 plans.rw Enumeration .1.3.6.1.4.1.562.36.2.1.70.2.3.2.10.1.1 |
mscFrNniDnaHgMHgAddrDataNetworkAddressThis attribute contains digits which form the unique identifier of the
customer interface. It can be compared (approximation only) to a
telephone number where the phone number identifies a unique
telephone set. DNA digits are selected and assigned by network
operators.rw DigitString .1.3.6.1.4.1.562.36.2.1.70.2.3.2.10.1.2 |
mscFrNniDnaHgMIfTableThis group contains the interface parameters between the
HuntGroupMember and the hunt group server. SEQUENCE OF MscFrNniDnaHgMIfEntry .1.3.6.1.4.1.562.36.2.1.70.2.3.10 |
mscFrNniDnaHgMIfEntryAn entry in the mscFrNniDnaHgMIfTable. MscFrNniDnaHgMIfEntry .1.3.6.1.4.1.562.36.2.1.70.2.3.10.1 |
mscFrNniDnaHgMAvailabilityUpdateThresholdThis attribute specifies how much availableAggregateCIR can
change before an Availability Message Packet (AMP) is sent to the
hunt group server informing it of the change.
If the value specified is not a multiple of 2048, the value actually
used as the threshold will be the next higher multiple of 2048.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.2.3.10.1.1 |
mscFrNniDnaHgMOpTableThis group contains the operational attributes of the
HuntGroupMember component. SEQUENCE OF MscFrNniDnaHgMOpEntry .1.3.6.1.4.1.562.36.2.1.70.2.3.11 |
mscFrNniDnaHgMOpEntryAn entry in the mscFrNniDnaHgMOpTable. MscFrNniDnaHgMOpEntry .1.3.6.1.4.1.562.36.2.1.70.2.3.11.1 |
mscFrNniDnaHgMMaximumAvailableAggregateCirThis attribute indicates the maximum available bandwidth for this
hunt group member. This value represents the total sum of the
sixteen egress bandwidth pools. It is the sum of the sixteen indices
of the FrNni Ca egressBandwidthPool attribute multiplied by the
link speed.roobsolete Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.2.3.11.1.1 |
mscFrNniDnaHgMAvailableAggregateCirThis attribute indicates the current total available bandwidth
reported to the hunt group server in the Availability Message Packet
(AMP). This value represents the sum of the sixteen currently
available egress bandwidth pools. It is the sum of the sixteen indices
of the FrNni Ca egressPoolAvailableBandwidth attribute.
It increments when a connection is released.
It decrements when a connection is accepted.
Both this attribute and the availableDlcis attribute must be non zero
for this interface to receive calls on a hunt group.roobsolete Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.2.3.11.1.2 |
mscFrNniDnaHgMAvailabilityDeltaThis attribute indicates the net change in the available aggregate
CIR since the last Availability Message Packet (AMP) was sent to
the Hunt Group. Once the absolute value of this attribute reaches
the availabilityUpdateThreshold an AMP is sent to the hunt group
server(s) and the availabilityDelta is re-computed.ro INTEGER (-16777216..16777215) .1.3.6.1.4.1.562.36.2.1.70.2.3.11.1.3 |
mscFrNniDnaHgMAvailableDlcisThis attribute indicates the number of DLCIs available for SVCs on
the interface associated with this DNA. If this value reaches 0, an
AMP with zero availability is sent to the hunt group server(s).
Both this attribute and the availableAggregateCir attribute must be
non zero for this DNA to receive calls on the hunt group.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.2.3.11.1.5 |
mscFrNniDnaHgMMaximumAvailableAggregateCir64This attribute indicates the maximum available bandwidth for this
hunt group member. This value represents the total sum of the
sixteen egress bandwidth pools. It is the sum of the sixteen indices
of the FrNni Ca egressBandwidthPool attribute multiplied by the
link speed.ro Unsigned64 .1.3.6.1.4.1.562.36.2.1.70.2.3.11.1.6 |
mscFrNniDnaHgMAvailableAggregateCir64This attribute indicates the current total available bandwidth
reported to the hunt group server in the Availability Message Packet
(AMP). This value represents the sum of the sixteen currently
available egress bandwidth pools. It is the sum of the sixteen indices
of the FrNni Ca egressPoolAvailableBandwidth attribute.
It increments when a connection is released.
It decrements when a connection is accepted.
Both this attribute and the availableDlcis attribute must be non zero
for this interface to receive calls on a hunt group.ro Unsigned64 .1.3.6.1.4.1.562.36.2.1.70.2.3.11.1.7 |
mscFrNniDnaAddressTableThis group contains attributes common to all DNAs. Every DNA
used in the network is defined with this group of 2 attributes. SEQUENCE OF MscFrNniDnaAddressEntry .1.3.6.1.4.1.562.36.2.1.70.2.10 |
mscFrNniDnaAddressEntryAn entry in the mscFrNniDnaAddressTable. MscFrNniDnaAddressEntry .1.3.6.1.4.1.562.36.2.1.70.2.10.1 |
mscFrNniDnaNumberingPlanIndicatorThis attribute indicates the Numbering Plan Indicator (NPI) of the
DNA that is entered. Address may belong to X.121 or E.164 plans.
X.121 is used in packet switched data networks.rw Enumeration .1.3.6.1.4.1.562.36.2.1.70.2.10.1.1 |
mscFrNniDnaDataNetworkAddressThis attribute indicates the customer's unique identifier. It is the
equivalent of the telephone number in the telephone network.rw DigitString .1.3.6.1.4.1.562.36.2.1.70.2.10.1.2 |
mscFrNniDnaOutgoingOptionsTableThis group defines DNA call options for calls made from the
interface. These options are not used for calls arriving to the
interface represented by this DNA. SEQUENCE OF MscFrNniDnaOutgoingOptionsEntry .1.3.6.1.4.1.562.36.2.1.70.2.11 |
mscFrNniDnaOutgoingOptionsEntryAn entry in the mscFrNniDnaOutgoingOptionsTable. MscFrNniDnaOutgoingOptionsEntry .1.3.6.1.4.1.562.36.2.1.70.2.11.1 |
mscFrNniDnaOutDefaultPriorityThis attribute indicates the default priority of outgoing calls from
the DTE to the network.
It can be overridden by the discardPriority under DLCI Direct Call
subcomponent.
This option can be also included in X.25 signalling, in such case it
will be overruled.rw Enumeration .1.3.6.1.4.1.562.36.2.1.70.2.11.1.7 |
mscFrNniDnaOutDefaultPathSensitivityThis attribute specifies the default class of path sensitivity to
network for all outgoing calls that use this DNA. The chosen default
class of path sensitivity applies to all outgoing calls established
using this DNA.
This attribute, if set to throughput, indicates that the default class is
throughput sensitive. If set to delay, then the default class is delay
sensitive. The default of outDefaultPathSensitivity is throughput.rwobsolete Enumeration .1.3.6.1.4.1.562.36.2.1.70.2.11.1.11 |
mscFrNniDnaOutPathSensitivityOverRideIf this attribute is set to yes in the call request, the called end will
use the calling end provisioning data on path sensitivity to override
its own provisioning data.
The default of outPathSensitivityOverRide is yes.rwobsolete Enumeration .1.3.6.1.4.1.562.36.2.1.70.2.11.1.12 |
mscFrNniDnaOutDefaultPathReliabilityThis attribute specifies the default class of routing for reliability
routing for all outgoing calls (from the DTE to the network) using
this particular DNA. The chosen default class of routing applies to
all outgoing calls established using this DNA, and applies to the
packets travelling in both directions on all outgoing calls (local to
remote, and remote to local). For incoming calls, the default class of
routing is chosen by the calling party (as opposed to DPN, where
either end of the call can choose the default routing class).
This attribute, if set to a value of normal, indicates that the default
class of routing is normal reliability routing. If set to a value of
high, then the default class of routing is high reliability routing.
High reliability is the standard choice for most DPN and Passport
services. It usually indicates that packets are overflowed or
retransmitted at various routing levels. Typically high reliability
results in duplication and disordering of packets in the network
when errors are detected or during link congestion. However, the
VC handles the duplication and disordering to ensure that packets
are delivered to the DTE properly.
For the Frame Relay service, duplication of packets is not desired,
in which case, normal reliability may be chosen as the preferred
class of routing.rw Enumeration .1.3.6.1.4.1.562.36.2.1.70.2.11.1.14 |
mscFrNniDnaOutAccessThis attribute is an extension of the Closed User Group (CUG)
facility, as follows:
This attribute, if set to a value of allowed indicates that outgoing
calls (from the DTE to the network) to the open (non-CUG) part of
the network are permitted. It also permits outgoing calls to DTEs
that have Incoming Access capabilities. If set to a value of
disallowed, then such calls cannot be made using this DNA. Such
calls will be cleared by the local DCE.
This attribute corresponds to the ITU-T 'Closed User Group with
Outgoing Access' feature for DNAs in that outgoing access is
granted if this attribute is set to a value of allowed.rwobsolete Enumeration .1.3.6.1.4.1.562.36.2.1.70.2.11.1.17 |
mscFrNniDnaDefaultTransferPriorityThis attribute specifies the default transfer priority for all outgoing
calls using this particular DNA. It can be overridden by the
transferPriority provisioned in the Dlci DirectCall sub-component.
The transfer priority is a preference configured for an application
according to its delay-sensitivity requirement. Frames with higher
transfer priority are served by the network before the frames with
lower priority. The transfer priority standard is defined to have 16
levels from 0 to 15.
Each transfer priority n, where n indicates the transfer priority
index, contains a default setting for routing class of service
(multimedia, delay or throughput) and frame relay egress queue
(depending on the number of supported egress queues on the remote
end interface) specified by the routingClassOfService and
emissionPriority attributes provisioned in the Mod Frs DprsNet
Tpm/n component. The default mapping can be altered by a user if
required.
The default defaultTransferPriority is 0.rw Enumeration .1.3.6.1.4.1.562.36.2.1.70.2.11.1.18 |
mscFrNniDnaTransferPriorityOverRideWhen this attribute is set to yes in the call request, the called end
will use the calling end provisioning data on transfer priority to
override its own provisioning data. If it is set no, the called end
will use its own provisioning data on transfer priority.
This attribute is not applicable for Frame Relay SVCs.
For more information about transfer priority, please refer to the
previous attribute defaultTransferPriority.
The default of transferPriorityOverRide is yes.rw Enumeration .1.3.6.1.4.1.562.36.2.1.70.2.11.1.19 |
mscFrNniDnaIncomingOptionsTableThis group defines options for incoming calls. These options are
used for calls arriving to the interface represented by this DNA. For
calls originated from the interface, IncomingOptions attributes are
not used. SEQUENCE OF MscFrNniDnaIncomingOptionsEntry .1.3.6.1.4.1.562.36.2.1.70.2.12 |
mscFrNniDnaIncomingOptionsEntryAn entry in the mscFrNniDnaIncomingOptionsTable. MscFrNniDnaIncomingOptionsEntry .1.3.6.1.4.1.562.36.2.1.70.2.12.1 |
mscFrNniDnaIncAccessThis attribute, if set to a value of allowed specifies that incoming
calls (from the network to the DTE) from the open (non-CUG) part
of the network are permitted. It also permits incoming calls from
DTEs that have outgoing access capabilities. If set to a value of
disallowed, such calls cannot be made to this DNA. They will be
cleared by the local DCE.
This attribute corresponds to the CCITT 'Closed User Group with
Incoming Access' feature for DNAs in that incoming access is
granted if this attribute is set to a value of allowed.rwobsolete Enumeration .1.3.6.1.4.1.562.36.2.1.70.2.12.1.9 |
mscFrNniDnaCallOptionsTableThis group defines additional all options for not related to direction
of the call. SEQUENCE OF MscFrNniDnaCallOptionsEntry .1.3.6.1.4.1.562.36.2.1.70.2.13 |
mscFrNniDnaCallOptionsEntryAn entry in the mscFrNniDnaCallOptionsTable. MscFrNniDnaCallOptionsEntry .1.3.6.1.4.1.562.36.2.1.70.2.13.1 |
mscFrNniDnaAccountClassThis attribute specifies the accounting class which is reserved for
network operations usage. Its value is returned in the accounting
record in the local and remote service type attributes. Use of this
attribute is decided by network operator.
This attribute is returned by the local VC in the accounting record
for all calls that are set up using this particular DNA.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.2.13.1.10 |
mscFrNniDnaAccountCollectionThis attribute indicates that accounting records are to be collected
by the network for the various reasons: billing, test, study, auditing.
The last of the parameters, force, indicates that accounting records
are to be collected irrespective of other collection reasons. The
force option is available for X.75 Gateways only. If none of these
reasons are set, then accounting will be suppressed.
To set a specific accounting collection reason, the reason is entered
and the corresponding bit in the structure is set to a value of 1. To
turn off a specific accounting collection reason, the reason is
entered preceded with the '~' character, and the corresponding bit in
the structure is set to a value of 0.
The bit placement for the accounting collection reasons is as
follows:
Bit 0 - Bill
Bit 1 - Test
Bit 2 - Study
Bit 3 - Audit
Bit 4 - Force
Description of bits:
bill(0)
test(1)
study(2)
audit(3)
force(4)rw OCTET STRING .1.3.6.1.4.1.562.36.2.1.70.2.13.1.11 |
mscFrNniDnaServiceExchangeThis attribute is an arbitrary number, Data Service Exchange, as
entered by the network operator and reported in accounting record.
It is converted into an internal 8-bit integer value for use in the
accounting record as well as in various X.25 and X.75 Tariff
utilities.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.2.13.1.12 |
mscFrNniDnaEgressAccountingThis attribute specifies if egress accounting is enabled by the frame
relay service. If egress accounting is disabled, only segment counts
are collected by the VC. No frame relay counts appear in the
accounting records for the frame relay service. If egress accounting
is enabled, the accounting records for the frame relay service will
contain frame relay specific counts.rw Enumeration .1.3.6.1.4.1.562.36.2.1.70.2.13.1.13 |
mscFrNniDnaDataPathThis attribute specifies the data path to be used by Virtual Circuits
on this interface. If the connection has a DirectCall component then
the value can be overridden by the dataPath attribute of the
DirectCall component.
This value applies to the connection after data transfer state is
reached. All the data and control trafic will be sent using this data
path. If the provisioned dataPath is not available the connection is
not established.
The value of the dataPath is signalled by both ends of the
connection. If this value is not the same at both ends dprsOnly is
used for the duration of the connection.
A virtual circuit connection is always established using dprsOnly
even if this attribute is provisioned as some other value.
dprsOnly - dynamic packet routing system is used
dprsMcsOnly - dprs Multi-Service Cut-Through Switching path is
used.
dprsMcsFirst - dprs Multi-Service Cut-Through Switching path is
used if it is available. If it is not avaliable dprsOnly is used.rw Enumeration .1.3.6.1.4.1.562.36.2.1.70.2.13.1.21 |
mscFrNniFramer OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.1.70.3 |
mscFrNniFramerRowStatusTableThis entry controls the addition and deletion of
mscFrNniFramer components. SEQUENCE OF MscFrNniFramerRowStatusEntry .1.3.6.1.4.1.562.36.2.1.70.3.1 |
mscFrNniFramerRowStatusEntryA single entry in the table represents a single
mscFrNniFramer component. MscFrNniFramerRowStatusEntry .1.3.6.1.4.1.562.36.2.1.70.3.1.1 |
mscFrNniFramerRowStatusThis variable is used as the basis for SNMP naming of
mscFrNniFramer components.
These components can be added and deleted.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.3.1.1.1 |
mscFrNniFramerComponentNameThis variable provides the component's string name for
use with the ASCII Console Interfacero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.3.1.1.2 |
mscFrNniFramerStorageTypeThis variable represents the storage type value for the
mscFrNniFramer tables.ro StorageType (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.3.1.1.4 |
mscFrNniFramerIndexThis variable represents the index for the mscFrNniFramer tables. NonReplicated .1.3.6.1.4.1.562.36.2.1.70.3.1.1.10 |
mscFrNniFramerProvTableThis group contains the base provisioning data for the Framer
component. Application or hardware interface specific provisioning
data is contained in other provisionable Framer groups. SEQUENCE OF MscFrNniFramerProvEntry .1.3.6.1.4.1.562.36.2.1.70.3.10 |
mscFrNniFramerProvEntryAn entry in the mscFrNniFramerProvTable. MscFrNniFramerProvEntry .1.3.6.1.4.1.562.36.2.1.70.3.10.1 |
mscFrNniFramerInterfaceNameThis attribute contains a hardware component name.
The attribute associates the application with a specific link. This
defines the module processor on which Framer's parent component
(as well as Framer itself) will run.rw Link .1.3.6.1.4.1.562.36.2.1.70.3.10.1.1 |
mscFrNniFramerLinkTableThis group contains attributes defining the framing of data on the
link interface. SEQUENCE OF MscFrNniFramerLinkEntry .1.3.6.1.4.1.562.36.2.1.70.3.11 |
mscFrNniFramerLinkEntryAn entry in the mscFrNniFramerLinkTable. MscFrNniFramerLinkEntry .1.3.6.1.4.1.562.36.2.1.70.3.11.1 |
mscFrNniFramerDataInversionThis attribute determines whether data bits are to be inverted (1 to 0
and 0 to 1) before transmission of frames to the interface. If the
value of this attribute is On, the incoming data bits will also be
inverted when frames are received from the link before being
processed.
This option is typically used in hdlc framing mode when inversion
is used to guarantee 1's density.
Note that aborts (in hdlc and interrupting modes) are corrupted
when data is inverted.
This attribute may only take its default value for non-MSA cards.rw Enumeration .1.3.6.1.4.1.562.36.2.1.70.3.11.1.2 |
mscFrNniFramerFrameCrcTypeThis attribute defines the type of CRC used.
The CRC value calculated is appended to the end of the frames
transmitted to the link. The CRC value is removed from the end of
frames received from the link and checked for correctness.
NoCrc means that CRC is not used.
This attribute may take only its default value for non-MSA cards.rw Enumeration .1.3.6.1.4.1.562.36.2.1.70.3.11.1.3 |
mscFrNniFramerFlagsBetweenFramesThis attribute defines the number of flags that are inserted between
frames sent to the link interface.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.3.11.1.4 |
mscFrNniFramerStateTableThis group contains the three OSI State attributes. The descriptions
generically indicate what each state attribute implies about the
component. Note that not all the values and state combinations
described here are supported by every component which uses this
group. For component-specific information and the valid state
combinations, refer to NTP 241-7001-150, Passport Operations and
Maintenance Guide. SEQUENCE OF MscFrNniFramerStateEntry .1.3.6.1.4.1.562.36.2.1.70.3.12 |
mscFrNniFramerStateEntryAn entry in the mscFrNniFramerStateTable. MscFrNniFramerStateEntry .1.3.6.1.4.1.562.36.2.1.70.3.12.1 |
mscFrNniFramerAdminStateThis attribute indicates the OSI Administrative State of the
component.
The value locked indicates that the component is administratively
prohibited from providing services for its users. A Lock or Lock -
force command has been previously issued for this component.
When the value is locked, the value of usageState must be idle.
The value shuttingDown indicates that the component is
administratively permitted to provide service to its existing users
only. A Lock command was issued against the component and it is
in the process of shutting down.
The value unlocked indicates that the component is administratively
permitted to provide services for its users. To enter this state, issue
an Unlock command to this component.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.3.12.1.1 |
mscFrNniFramerOperationalStateThis attribute indicates the OSI Operational State of the component.
The value enabled indicates that the component is available for
operation. Note that if adminState is locked, it would still not be
providing service.
The value disabled indicates that the component is not available for
operation. For example, something is wrong with the component
itself, or with another component on which this one depends. If the
value is disabled, the usageState must be idle.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.3.12.1.2 |
mscFrNniFramerUsageStateThis attribute indicates the OSI Usage State of the component.
The value idle indicates that the component is not currently in use.
The value active indicates that the component is in use and has
spare capacity to provide for additional users.
The value busy indicates that the component is in use and has no
spare operating capacity for additional users at this time.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.3.12.1.3 |
mscFrNniFramerStatsTableThis group contains the operational statistics data for a Framer
component. SEQUENCE OF MscFrNniFramerStatsEntry .1.3.6.1.4.1.562.36.2.1.70.3.13 |
mscFrNniFramerStatsEntryAn entry in the mscFrNniFramerStatsTable. MscFrNniFramerStatsEntry .1.3.6.1.4.1.562.36.2.1.70.3.13.1 |
mscFrNniFramerFrmToIfThe number of frames transmitted to the link interface by Framer.
Note: This does not include the number of frames transmitted
directly to the hardware queue, thus bypassing the Framer
component.roobsolete Counter32 .1.3.6.1.4.1.562.36.2.1.70.3.13.1.1 |
mscFrNniFramerFrmFromIfThe number of frames received from the link interface by Framer.roobsolete Counter32 .1.3.6.1.4.1.562.36.2.1.70.3.13.1.2 |
mscFrNniFramerOctetFromIfThe number of bytes received from the link interface by Framer.roobsolete Counter32 .1.3.6.1.4.1.562.36.2.1.70.3.13.1.3 |
mscFrNniFramerAbortsThis attribute is the total number of aborts received.ro Counter32 .1.3.6.1.4.1.562.36.2.1.70.3.13.1.4 |
mscFrNniFramerCrcErrorsThis attribute is the total number of frames with CRC errors,
occurring in the receive direction from the link.ro Counter32 .1.3.6.1.4.1.562.36.2.1.70.3.13.1.5 |
mscFrNniFramerLrcErrorsThis attribute is the total number of frames with LRC errors,
occurring in the Tx link prior to transmission onto the link.ro Counter32 .1.3.6.1.4.1.562.36.2.1.70.3.13.1.6 |
mscFrNniFramerNonOctetErrorsThis attribute is the total number of frames that were non octet
aligned.ro Counter32 .1.3.6.1.4.1.562.36.2.1.70.3.13.1.7 |
mscFrNniFramerOverrunsThis attribute is the total number of frames received from the link
for which overruns occurred.ro Counter32 .1.3.6.1.4.1.562.36.2.1.70.3.13.1.8 |
mscFrNniFramerUnderrunsThis attribute is the total number of frames transmitted to the link
for which underruns occurred.ro Counter32 .1.3.6.1.4.1.562.36.2.1.70.3.13.1.9 |
mscFrNniFramerLargeFrmErrorsThis attribute is the total number of frames received which were too
large. The frame execeeded the maximumFrameLengthLimit
provisioned attribute or it contained more than the 255 block
hardware limit.ro Counter32 .1.3.6.1.4.1.562.36.2.1.70.3.13.1.10 |
mscFrNniFramerFrmModeErrorsThis attribute is the total number of frames detected with framing
mode errors. A framingModeError is flagged when frames are
inconsistent with the specified framingType, that is when
interrupting frames are used while running in hdlc mode.ro Counter32 .1.3.6.1.4.1.562.36.2.1.70.3.13.1.11 |
mscFrNniFramerFrmToIf64The number of frames transmitted to the link interface by Framer.
Note: This does not include the number of frames transmitted
directly to the hardware queue, thus bypassing the Framer
component.ro PassportCounter64 .1.3.6.1.4.1.562.36.2.1.70.3.13.1.14 |
mscFrNniFramerFrmFromIf64The number of frames received from the link interface by Framer.ro PassportCounter64 .1.3.6.1.4.1.562.36.2.1.70.3.13.1.15 |
mscFrNniFramerOctetFromIf64The number of bytes received from the link interface by Framer.ro PassportCounter64 .1.3.6.1.4.1.562.36.2.1.70.3.13.1.16 |
mscFrNniFramerUtilTableThis group contains the link utilizaiton operational data for a
Framer component. SEQUENCE OF MscFrNniFramerUtilEntry .1.3.6.1.4.1.562.36.2.1.70.3.14 |
mscFrNniFramerUtilEntryAn entry in the mscFrNniFramerUtilTable. MscFrNniFramerUtilEntry .1.3.6.1.4.1.562.36.2.1.70.3.14.1 |
mscFrNniFramerNormPrioLinkUtilToIfThis attribute is the utilization of the normal and high priority data
traffic (interruptable traffic) sent to the link as a percentage of the
available bandwidth on the link. Note that this indluces traffic with
Transfer Priorities (TP) of 0, 6 and 9 and/or Emission Priority of 2
and 3. The utilization is the average for the last minute.ro Gauge32 .1.3.6.1.4.1.562.36.2.1.70.3.14.1.1 |
mscFrNniFramerNormPrioLinkUtilFromIfThis attribute is the utilization of the normal and high priority data
traffic (interruptable traffic) received from the link as a percentage
of the available bandwidth on the link. Note that this includes traffic
with Transfer Priorities (TP) of 0, 6 and 9 and/or Emission Priority
of 2 and 3. The utilization is the average for the last minute.ro Gauge32 .1.3.6.1.4.1.562.36.2.1.70.3.14.1.3 |
mscFrNniLmi OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.1.70.4 |
mscFrNniLmiRowStatusTableThis entry controls the addition and deletion of
mscFrNniLmi components. SEQUENCE OF MscFrNniLmiRowStatusEntry .1.3.6.1.4.1.562.36.2.1.70.4.1 |
mscFrNniLmiRowStatusEntryA single entry in the table represents a single
mscFrNniLmi component. MscFrNniLmiRowStatusEntry .1.3.6.1.4.1.562.36.2.1.70.4.1.1 |
mscFrNniLmiRowStatusThis variable is used as the basis for SNMP naming of
mscFrNniLmi components.
These components cannot be added nor deleted.ro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.4.1.1.1 |
mscFrNniLmiComponentNameThis variable provides the component's string name for
use with the ASCII Console Interfacero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.4.1.1.2 |
mscFrNniLmiStorageTypeThis variable represents the storage type value for the
mscFrNniLmi tables.ro StorageType (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.4.1.1.4 |
mscFrNniLmiIndexThis variable represents the index for the mscFrNniLmi tables. NonReplicated .1.3.6.1.4.1.562.36.2.1.70.4.1.1.10 |
mscFrNniLmiParmsTableThis group contains the provisionable attributes of the Local
Management Interface component. SEQUENCE OF MscFrNniLmiParmsEntry .1.3.6.1.4.1.562.36.2.1.70.4.10 |
mscFrNniLmiParmsEntryAn entry in the mscFrNniLmiParmsTable. MscFrNniLmiParmsEntry .1.3.6.1.4.1.562.36.2.1.70.4.10.1 |
mscFrNniLmiProceduresThis attribute selects the procedures to be used for the Local
Management Interface. The following are the supported procedures:
none: Local Management Interface procedures are not running on
this interface. This accommodates Frame Relay user equipment
which didn't implement any LMI procedures. In this case, the
remaining attributes of this group are ignored.
ansi: Local Management Interface procedures from the ANSI
specification are supported. DLCI 0 is used for the LMI protocol.
itu: Local Management Interface procedures from the ITU-T
specification are supported. DLCI 0 is used for the LMI protocol.
Was previously ccitt.
autoConfigure: The interface determines automatically which Local
Management Interface procedures to use.
The procedures currently being used can be seen in the operational
attribute opProcedures.rw Enumeration .1.3.6.1.4.1.562.36.2.1.70.4.10.1.1 |
mscFrNniLmiAsyncStatusReportThis attribute selects the use of asynchronous PVC status report
procedures as specified in ANSI and CCITT specification.rw Enumeration .1.3.6.1.4.1.562.36.2.1.70.4.10.1.2 |
mscFrNniLmiErrorEventThresholdFor the network-side-procedure, an event is defined as follows: (1)
receipt of a STATUS ENQUIRY message, or (2) expiration of timer
T392. An error event is (1) nonreceipt of STATUS ENQUIRY in
T392 seconds; (2) invalid format of a LMI message; (3) invalid
receive sequence number.
For the user-side-procedure, an event is defined as a polling cycle or
a status enquiry and status report exchange. An error event is (1)
non-receipt of a STATUS within the polling cycle, or (2) invalid
format of a LMI message, or (3) invalid sequence number
This attribute specifies the number of error events which, if they
occur within eventCount events, will cause a protocol error
condition. The condition is cleared after eventCount sequential
correct events occur.
It must be less than or equal to eventCount (n393)rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.4.10.1.3 |
mscFrNniLmiEventCountThis attribute specifies the number of contiguous events within
which no more than eventErrorThreshold error events are allowed.
It must be greater than or equal to errorEventThreshold (n392).rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.4.10.1.4 |
mscFrNniLmiCheckPointTimerThis attribute selects the time (in seconds) within which a STATUS
ENQUIRY message is expected. It must be greater than
linkVerificationTimer (t391).rw Unsigned32 (5 | 10 | 15 | 20 | 25 | 30) .1.3.6.1.4.1.562.36.2.1.70.4.10.1.5 |
mscFrNniLmiIgnoreActiveBitThis attribute specifies whether the Frame Relay LMI Active Bit
(A-bit) has a bearing on the transfer of user data across this Frame
Relay interface for both directions of traffic flow.
When this attribute is set to yes, the A-bit status of a user DLCI
connection does not affect data transfer.
When this attribute is set to no, data received from the local
interface is discarded if an A-bit =0 condition exists towards the
local user. Data being sent to the local interface is discarded if an A-
bit = 0 condition exists towards the local user.rw Enumeration .1.3.6.1.4.1.562.36.2.1.70.4.10.1.7 |
mscFrNniLmiNniParmsTableThis group contains the provisionable attributes of the Local
Management Interface component which are unique to NNI. SEQUENCE OF MscFrNniLmiNniParmsEntry .1.3.6.1.4.1.562.36.2.1.70.4.11 |
mscFrNniLmiNniParmsEntryAn entry in the mscFrNniLmiNniParmsTable. MscFrNniLmiNniParmsEntry .1.3.6.1.4.1.562.36.2.1.70.4.11.1 |
mscFrNniLmiFullStatusPollingCyclesThis attribute specifies how frequently the Frame Relay NNI service
should initiate a Status Enquiry for a full PVC status report. A
polling cycle is a Status Enquiry and Status Report exchange.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.4.11.1.1 |
mscFrNniLmiLinkVerificationTimerThis attribute specifies how frequently the Frame Relay NNI service
should initiate a Status Enquiry for link integrity verification. It
must be less than checkPointTimer (t392).rw Unsigned32 (5 | 10 | 15 | 20 | 25 | 30) .1.3.6.1.4.1.562.36.2.1.70.4.11.1.2 |
mscFrNniLmiStateTableThis group contains the three OSI State attributes. The descriptions
generically indicate what each state attribute implies about the
component. Note that not all the values and state combinations
described here are supported by every component which uses this
group. For component-specific information and the valid state
combinations, refer to NTP 241-7001-150, Passport Operations and
Maintenance Guide. SEQUENCE OF MscFrNniLmiStateEntry .1.3.6.1.4.1.562.36.2.1.70.4.12 |
mscFrNniLmiStateEntryAn entry in the mscFrNniLmiStateTable. MscFrNniLmiStateEntry .1.3.6.1.4.1.562.36.2.1.70.4.12.1 |
mscFrNniLmiAdminStateThis attribute indicates the OSI Administrative State of the
component.
The value locked indicates that the component is administratively
prohibited from providing services for its users. A Lock or Lock -
force command has been previously issued for this component.
When the value is locked, the value of usageState must be idle.
The value shuttingDown indicates that the component is
administratively permitted to provide service to its existing users
only. A Lock command was issued against the component and it is
in the process of shutting down.
The value unlocked indicates that the component is administratively
permitted to provide services for its users. To enter this state, issue
an Unlock command to this component.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.4.12.1.1 |
mscFrNniLmiOperationalStateThis attribute indicates the OSI Operational State of the component.
The value enabled indicates that the component is available for
operation. Note that if adminState is locked, it would still not be
providing service.
The value disabled indicates that the component is not available for
operation. For example, something is wrong with the component
itself, or with another component on which this one depends. If the
value is disabled, the usageState must be idle.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.4.12.1.2 |
mscFrNniLmiUsageStateThis attribute indicates the OSI Usage State of the component.
The value idle indicates that the component is not currently in use.
The value active indicates that the component is in use and has
spare capacity to provide for additional users.
The value busy indicates that the component is in use and has no
spare operating capacity for additional users at this time.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.4.12.1.3 |
mscFrNniLmiPsiTableThis group provides the protocol status of the Local Management
Interface. SEQUENCE OF MscFrNniLmiPsiEntry .1.3.6.1.4.1.562.36.2.1.70.4.13 |
mscFrNniLmiPsiEntryAn entry in the mscFrNniLmiPsiTable. MscFrNniLmiPsiEntry .1.3.6.1.4.1.562.36.2.1.70.4.13.1 |
mscFrNniLmiProtocolStatusThis attribute indicates whether the LMI is in an error condition or
whether the LMI procedures are behaving normally. When
operating with no LMI protocol, this attribute is always set to
normalCondition. When operating with LMI procedures, this
attribute is set to errorCondition after n392 of the last n393 events
are in error. The consequence of an errorCondition is that all
DLCIs on this interface will become inactive in both directions. The
errorCondition is lifted and a normalCondition is indicated when a
sufficient number of events have occurred without error. In ANSI,
this occurs when n393 consecutive good events take place.
If the procedures attribute is set to autoConfigure, this attribute is
se to configuring while adaptive LMI determines which LMI
procedures are running on the link. A single LMI error event during
auto configuration causes the attribute value to change to
errorCondition. If during configuring no LMI message is received,
an LMI errorCondition is raised after n392 x t392 seconds.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.4.13.1.1 |
mscFrNniLmiOpProceduresThis attribute indicates the procedures being used for the Local
Management Interface. This attribute should be ignored if
protocolStatus is not normalCondition. The following procedures
are supported:
none: Local Management Interface procedures are not running on
this interface. This accommodates Frame Relay user equipment that
has not implemented any LMI procedures.
ansi: Local Management Interface procedures from the ANSI
specification are running. DLCI 0 is used for the LMI protocol.
itu: Local Management Interface procedures from the ITU-T
specification are running. DLCI 0 is used for the LMI protocol. Was
previously ccitt.
unknown: Local Management Interface procedures have yet to be
determined by Adaptive LMI.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.4.13.1.2 |
mscFrNniLmiStatsTableThis group contains the operational statistics for the Frame Relay
NNI Local Management Interface. SEQUENCE OF MscFrNniLmiStatsEntry .1.3.6.1.4.1.562.36.2.1.70.4.14 |
mscFrNniLmiStatsEntryAn entry in the mscFrNniLmiStatsTable. MscFrNniLmiStatsEntry .1.3.6.1.4.1.562.36.2.1.70.4.14.1 |
mscFrNniLmiKeepAliveStatusToIfThis attribute counts the number of Local Management Interface
keep alive status messages sent to the external network in response
to a status enquiry for keep alive status. When the maximum count
is exceeded it wraps to zero.ro Counter32 .1.3.6.1.4.1.562.36.2.1.70.4.14.1.1 |
mscFrNniLmiFullStatusToIfThis attribute counts the number of Local Management Interface
full status messages sent to the external network in response to a
status enquiry for keep alive or full status. When the maximum
count is exceeded it wraps to zero.ro Counter32 .1.3.6.1.4.1.562.36.2.1.70.4.14.1.2 |
mscFrNniLmiKeepAliveStatusEnqFromIfThis attribute counts the number of Local Management Interface
valid keep alive status enquiry messages received from the external
network. When the maximum count is exceeded it wraps to zero.ro Counter32 .1.3.6.1.4.1.562.36.2.1.70.4.14.1.3 |
mscFrNniLmiFullStatusEnqFromIfThis attribute counts the number of Local Management Interface
valid full status enquiry messages received from the external
network. When the maximum count is exceeded it wraps to zero.ro Counter32 .1.3.6.1.4.1.562.36.2.1.70.4.14.1.4 |
mscFrNniLmiNetworkSideEventHistoryThis attribute displays the Local Management Interface network
side procedure event history in order of occurrence. An event is
represented by a single symbol. A '+' symbol indicates a good
event. An 'X' symbol indicates a protocol error event. The leftmost
event is the most recent to occur. The provisioned eventCount (nN3/
N393) dictates the maximum number of events displayed. A good
event is triggered by receipt of a valid status enquiry message. An
error event is either a nT2/T392 timer expiry or receipt of a status
enquiry with bad sequence numbers.ro AsciiString .1.3.6.1.4.1.562.36.2.1.70.4.14.1.5 |
mscFrNniLmiUserSideEventHistoryThis attribute displays the Local Management Interface user side
procedure event history in order of occurrence. An event is
represented by a single symbol. A '+' symbol indicates a good
event. An 'X' symbol indicates a protocol error event. The leftmost
event is the most recent to occur. The provisioned eventCount (nN3/
N393) dictates the maximum number of events displayed. A good
event is triggered by receipt of a valid status message. An error
event is either a nT1/T391 timer expiry or receipt of a status
message with bad sequence numbers.ro AsciiString .1.3.6.1.4.1.562.36.2.1.70.4.14.1.6 |
mscFrNniLmiProtocolErrorsThis attribute counts the number of Local Management Interface
protocol errors. It is the sum of the sequence (sequenceErrors and
statusSequenceErrors) and timeout (pollingVerifTimeouts and
noStatusReportCount) errors. When the maximum count is
exceeded it wraps to zero.ro Counter32 .1.3.6.1.4.1.562.36.2.1.70.4.14.1.7 |
mscFrNniLmiUnexpectedIesThis attribute counts the number of Local Management Interface
frames received with an Information Element identifier that is
unknown or unexpected. An unexpected Information Element is not
a protocol error. When the maximum count is exceeded, this
counter wraps to zero.ro Counter32 .1.3.6.1.4.1.562.36.2.1.70.4.14.1.8 |
mscFrNniLmiSequenceErrorsThis attribute counts the number of Local Management Interface
Status Enquiry message sequence errors. A sequence error is receipt
of a Status Enquiry message with a receive sequence number not
equal to the last send sequence number. When the maximum count
is exceeded the counter wraps to zero.ro Counter32 .1.3.6.1.4.1.562.36.2.1.70.4.14.1.9 |
mscFrNniLmiStatusSequenceErrorsThis attribute counts the number of Local Management Interface
Status message sequence errors. A sequence error is receipt of a
Status message with a receive sequence number not equal to the last
send sequence number. When the maximum count is exceeded the
counter wraps to zero.ro Counter32 .1.3.6.1.4.1.562.36.2.1.70.4.14.1.10 |
mscFrNniLmiUnexpectedReportsThis attribute counts the number of Local Management Interface
frames received with an unknown or unexpected report type. An
unexpected report type is not a protocol error. When the maximum
count is exceeded the counter wraps to zero.ro Counter32 .1.3.6.1.4.1.562.36.2.1.70.4.14.1.11 |
mscFrNniLmiPollingVerifTimeoutsThis attribute counts the number of checkPointTImer (t392) timer
expiries occurring on the Local Management Interface. When the
maximum count is exceeded the counter wraps to zero.ro Counter32 .1.3.6.1.4.1.562.36.2.1.70.4.14.1.12 |
mscFrNniLmiNoStatusReportCountThis attribute counts the number of times when no status report or
an invalid status report comes from the external network. This
attribute is incremented in two cases:
i) after a status enquiry is sent out and T391 timer expires without
having a status report received.
ii) an invalid status report is received.
When the maximum count is exceeded it wraps to zero.ro Counter32 .1.3.6.1.4.1.562.36.2.1.70.4.14.1.13 |
mscFrNniDlci OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.1.70.5 |
mscFrNniDlciRowStatusTableThis entry controls the addition and deletion of
mscFrNniDlci components. SEQUENCE OF MscFrNniDlciRowStatusEntry .1.3.6.1.4.1.562.36.2.1.70.5.1 |
mscFrNniDlciRowStatusEntryA single entry in the table represents a single
mscFrNniDlci component. MscFrNniDlciRowStatusEntry .1.3.6.1.4.1.562.36.2.1.70.5.1.1 |
mscFrNniDlciRowStatusThis variable is used as the basis for SNMP naming of
mscFrNniDlci components.
These components can be added and deleted.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.5.1.1.1 |
mscFrNniDlciComponentNameThis variable provides the component's string name for
use with the ASCII Console Interfacero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.5.1.1.2 |
mscFrNniDlciStorageTypeThis variable represents the storage type value for the
mscFrNniDlci tables.ro StorageType (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.5.1.1.4 |
mscFrNniDlciIndexThis variable represents the index for the mscFrNniDlci tables. Integer32 .1.3.6.1.4.1.562.36.2.1.70.5.1.1.10 |
mscFrNniDlciDc OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.1.70.5.2 |
mscFrNniDlciDcRowStatusTableThis entry controls the addition and deletion of
mscFrNniDlciDc components. SEQUENCE OF MscFrNniDlciDcRowStatusEntry .1.3.6.1.4.1.562.36.2.1.70.5.2.1 |
mscFrNniDlciDcRowStatusEntryA single entry in the table represents a single
mscFrNniDlciDc component. MscFrNniDlciDcRowStatusEntry .1.3.6.1.4.1.562.36.2.1.70.5.2.1.1 |
mscFrNniDlciDcRowStatusThis variable is used as the basis for SNMP naming of
mscFrNniDlciDc components.
These components cannot be added nor deleted.ro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.5.2.1.1.1 |
mscFrNniDlciDcComponentNameThis variable provides the component's string name for
use with the ASCII Console Interfacero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.5.2.1.1.2 |
mscFrNniDlciDcStorageTypeThis variable represents the storage type value for the
mscFrNniDlciDc tables.ro StorageType (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.5.2.1.1.4 |
mscFrNniDlciDcIndexThis variable represents the index for the mscFrNniDlciDc tables. NonReplicated .1.3.6.1.4.1.562.36.2.1.70.5.2.1.1.10 |
mscFrNniDlciDcOptionsTableThis group defines attributes associated with a direct call. It defines
connection in terms of path and call option parameters. This
connection can be permanent (PVC), switched (SVC), or switched
permanent (SPVC). It can have four facilities:
- CCITT Facilities
- DTE Facilities
- National Facilities
- International Facilities
The total number of bytes of facilities including the facility codes
and all of the facility data from all of the four classes of facilities
must not exceed 512 bytes. SEQUENCE OF MscFrNniDlciDcOptionsEntry .1.3.6.1.4.1.562.36.2.1.70.5.2.10 |
mscFrNniDlciDcOptionsEntryAn entry in the mscFrNniDlciDcOptionsTable. MscFrNniDlciDcOptionsEntry .1.3.6.1.4.1.562.36.2.1.70.5.2.10.1 |
mscFrNniDlciDcRemoteNpiThis attribute specifies the Numbering Plan Indicator (NPI) of the
remoteDna.rw Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.2.10.1.3 |
mscFrNniDlciDcRemoteDnaThis attribute specifies the Data Network Address (DNA) of the
service at the remote end of the DLCI. This is the called
(destination) DCE address (DNA) of this PVC.rw DigitString .1.3.6.1.4.1.562.36.2.1.70.5.2.10.1.4 |
mscFrNniDlciDcRemoteDlciThis attribute specifies the remote DLCI of the PVC connection.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.2.10.1.5 |
mscFrNniDlciDcTypeThis attribute specifies the type of VC call.
If the value is set to permanentMaster, then a permanent
connection will be established between two ends. The remote end
must be defined as a permanentSlave, permanentBackupSlave, or
permanentSlaveWithBackup. The connection cannot be established
if the remote end is defined as anything else. The end defined as
permanentMaster always initiates the calls. It attempts to call once
per minute.
If the value is set to permanentSlave then a permanent connection
will be established between two ends. The remote end must be
defined as a permanentMaster. The connection cannot be
established if the remote end is defined as anything else. The
permanentSlave end attempts to call once per minute.
If the value is set to permanentSlaveWithBackup then a permanent
connection will be established between the two ends. The remote
end must be defined as a permanentMaster. The connection cannot
be established if the remote interface is defined as anything else.
The permanentSlaveWithBackup attempts to call once per minute.
When type is set to permanentSlaveWithBackup, the connection is
cleared if the interface becomes unavailable. This enables a retry of
the connection which can be redirected to the
permanentBackupSlave.
If the value is set to permanentBackupSlave then a permanent
connection is established between the two ends only if the
permanentMaster end is disconnected from the
permanentSlaveWithBackup end and a backup call is established
by the call redirection system. If the permanentSlaveWithBackup
interface becomes available again, the permanentBackupSlave end
is disconnected and the permanentSlaveWithBackup end is
reconnected to the permanentMaster end. The
permanentBackupSlave end does not try to establish a call.
If the value is set to spvcMaster, then a permanent connection is
established between two ends, with resiliency at the NNI), if the
connection transits across two or more networks. The remote end,
which may be in the same network, or an external network that is
reachable via Frame Relay NNIs, must be defined as either a
spvcSlave, spvcBackupSlave or spvcSlaveWithBackup. The
connection cannot be established if the remote end is defined as
anything else. The end defined as spvcMaster always initiates the
call. It attempts to call once per minute. The call is attempted by the
spvcMaster and accepted by the remote end only if all of the
following conditions are satisfied, at both ends:
1. The physical layer must be operational.
2. The LMI procedures must be in normalCondition (that is, no
service affecting condition).
3. If the LMI side attribute is provisioned to both, the A-bit
received from the interface must be Active. If the LMI side
attribute is not provisioned to both, this condition does not
apply.
After a call is cleared, the spvcMaster end attempts to retry the call
according to the rule for the clear cause. If the call is cleared or
rejected due to the failure of one of the three conditions indicated
above, or due to unavailability of resources along any point in the
connection path, the call will be retried after 60 seconds. For all
other causes, such as loss of service at an NNI, the call will be
retried immediately.
If the value is set to spvcSlave then an SPVC connection is
established between two ends. The remote end must be defined as
an spvcMaster. The connection cannot be established if the remote
end is defined as anything else. The spvcSlave end does not attempt
to call.
If the value is set to spvcSlaveWithBackup then a SPVC connection
is established between the two ends. The remote end must be
defined as an spvcMaster. The connection cannot be established if
the remote interface end is defined as anything else. Unlike a
permanentSlaveWithBackup end, the spvcSlaveWithBackup end
does not attempt to call. If the value is set to spvcSlaveWithBackup,
the connection is cleared if the interface becomes unavailable. This
enables a retry of the connection by the spvcMaster end, which may
be redirected to an end that is set to spvcBackupSlave.
If the value is set to spvcBackupSlave then an SPVC connection is
established between the two ends only if the spvcMaster end is
disconnected from the spvcSlaveWithBackup end, and a backup
call is redirected by the call redirection system. Unlike the PVC
connection, if the spvcSlaveWithBackup interface becomes
available again, the spvcBackupSlave end is not disconnected and
the spvcSlaveWithBackup end is not reconnected to the spvcMaster
end. Neither the spvcBackupSlave nor the spvcSlaveWithBackup
ends try to establish an SPVC call.rw Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.2.10.1.6 |
mscFrNniDlciDcTransferPriorityThis attribute specifies the transfer priority to the local network for
the outgoing calls using this particular DLCI. It overrides the
defaultTransferPriority provisioned in its associated Dna
component.
The transfer priority is a preference configured for an application
according to its delay-sensitivity requirement. Frames with higher
transfer priority are served by the network before the frames with
lower priority. The transfer priority standard is defined to have 16
levels from 0 to 15.
Each transfer priority n, where n is the transfer priority index, has a
default setting for routing class of service (multimedia, delay, or
throughput) and Frame Relay egress queue (depending on the
number of supported egress queues on the remote end interface).
These settings are specified by the routingClassOfService and
emissionPriority attributes provisioned under the Mod Frs DprsNet
Tpm/n component.
Specifying useDnaDefTP means using the value given by
defaultTransferPriority in the associated Dna for this DLCI.rw Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.2.10.1.9 |
mscFrNniDlciDcDiscardPriorityThis attribute specifies the discard priority for outgoing call using
this DLCI.
The discard priority has three provisioning values: normal, high,
and useDnaDefPriority. Under congestion conditions, traffic with
normal priority is discarded before traffic with high priority. The
Dna default value (provisioned by outDefaultPriority) is taken if
this attribute is set to the value useDnaDefPriority.rw Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.2.10.1.10 |
mscFrNniDlciDcDeDiscardPriorityThis attribute specifies whether the discardPriority applies to DE
frames for this DLCI.
When set to determinedByDiscardPriority, traffic with DE bit set
will be discarded according to the setting of the discardPriority.
When set to lowest, all traffic with DE bit set is treated the same and
is sent to the subnet at the lowest discard priority.rw Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.2.10.1.11 |
mscFrNniDlciDcDataPathThis attribute specifies the data path to be used by Virtual Circuits
on this interface. The value of the dataPath attribute in the Dna
component is overridden by this attribute if the value is not
useDnaValue.
This value applies to the connection after data transfer state is
reached. All the data and control traffic will be sent using this data
path. If the provisioned dataPath is not available the connection is
not established.
The value of the dataPath is signalled by both ends of the
connection. If this value is not the same at both ends dprsOnly is
used for the duration of the connection.
A virtual circuit connection is always established using dprsOnly
even if this attribute is provisioned as some other value.
dprsOnly - The dynamic packet routing system is used.
dprsMcsOnly - The DPRS Multi-Service Cut-Through Switching
path is used.
dprsMcsFirst - The DPRS Multi-Service Cut-Through Switching
path is used if it is available. If it is not available, dprsOnly is used.
useDnaValue - The routing system used is based on the value
provisioned in the Dna component.rw Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.2.10.1.12 |
mscFrNniDlciDcCugIndexThis attribute specifies the CUG index which is to be signalled in
PVC and SPVC call requests to the remote end.
The type of CUG signalling is defined in attribute cugType in this
component.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.2.10.1.13 |
mscFrNniDlciDcCugTypeThis attribute specifies the type of CUG signalling to be used in
PVC and SPVC call requests. Index of CUG to be used is defined in
attribute cugIndex in this component.
Possible values are:
cug - signal CUG
cugOa - signal CUG with outgoing access
doNotSignal - no CUG in call requestrw Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.2.10.1.14 |
mscFrNniDlciDcMapIpCosToFrQosThis attribute specifies whether an IP TOS value is mapped to an
FR QOS. The mapping used is provisioned in the Mod Frs
IpCosToFrQos component.
When this attribute is set to yes, at Frame Relay egress, the IP TOS
byte in each frame is checked. The TOS value determines the egress
emission queue and the discard priority for that frame.
When this attribute is set to no, FR QOS is determined by the
provisioned discard priority and transfer priority.rw Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.2.10.1.15 |
mscFrNniDlciDcNfaTableThis is the i'th National facility required for this direct call. Within
the provisioning system, the user specifies the facility code along
with the facility parameters. The facility is represented internally as
a hexadecimal string following the X.25 ITU-T representation for
facility data.
Two explicit attributes discardPriority and pathSensitivity are
created to replace H.01 and H.30 in the group
VcsDirectCallOptionsProv of this file. The migrate escape here
(DcComponent::migrateFaxEscape) propagates the old provisioning
data under H.01 and H.30 into discardPriority and transferPriority.
The rule of the above propagation are: 0 in H.01 is equivalent to
discardPriority 0; 1 in H.01 is equivalent to discardPriority 1. And 0
in H.30 is equivalent to transferPriority throughput; 1 in H.30 is
equivalent to pathSensitivity delay.
Please refer to discardPriority and pathSensitivity for more
information on how to use them.obsolete SEQUENCE OF MscFrNniDlciDcNfaEntry .1.3.6.1.4.1.562.36.2.1.70.5.2.202 |
mscFrNniDlciDcNfaEntryAn entry in the mscFrNniDlciDcNfaTable.obsolete MscFrNniDlciDcNfaEntry .1.3.6.1.4.1.562.36.2.1.70.5.2.202.1 |
mscFrNniDlciDcNfaIndexThis variable represents the index for the mscFrNniDlciDcNfaTable.obsolete Integer32 (1 | 48) .1.3.6.1.4.1.562.36.2.1.70.5.2.202.1.1 |
mscFrNniDlciDcNfaValueThis variable represents an individual value for the
mscFrNniDlciDcNfaTable.rwobsolete HexString .1.3.6.1.4.1.562.36.2.1.70.5.2.202.1.2 |
mscFrNniDlciDcNfaRowStatusThis variable is used to control the addition and deletion
of individual values of the mscFrNniDlciDcNfaTable.rwobsolete RowStatus (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.5.2.202.1.3 |
mscFrNniDlciVc OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.1.70.5.3 |
mscFrNniDlciVcRowStatusTableThis entry controls the addition and deletion of
mscFrNniDlciVc components. SEQUENCE OF MscFrNniDlciVcRowStatusEntry .1.3.6.1.4.1.562.36.2.1.70.5.3.1 |
mscFrNniDlciVcRowStatusEntryA single entry in the table represents a single
mscFrNniDlciVc component. MscFrNniDlciVcRowStatusEntry .1.3.6.1.4.1.562.36.2.1.70.5.3.1.1 |
mscFrNniDlciVcRowStatusThis variable is used as the basis for SNMP naming of
mscFrNniDlciVc components.
These components cannot be added nor deleted.ro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.5.3.1.1.1 |
mscFrNniDlciVcComponentNameThis variable provides the component's string name for
use with the ASCII Console Interfacero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.5.3.1.1.2 |
mscFrNniDlciVcStorageTypeThis variable represents the storage type value for the
mscFrNniDlciVc tables.ro StorageType (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.5.3.1.1.4 |
mscFrNniDlciVcIndexThis variable represents the index for the mscFrNniDlciVc tables. NonReplicated .1.3.6.1.4.1.562.36.2.1.70.5.3.1.1.10 |
mscFrNniDlciVcCadTableThis group represents operational call data related to Frame Relay
Vc. It can be displayed only for Frame Relay Vc which is created by
application. SEQUENCE OF MscFrNniDlciVcCadEntry .1.3.6.1.4.1.562.36.2.1.70.5.3.10 |
mscFrNniDlciVcCadEntryAn entry in the mscFrNniDlciVcCadTable. MscFrNniDlciVcCadEntry .1.3.6.1.4.1.562.36.2.1.70.5.3.10.1 |
mscFrNniDlciVcTypeThis attribute displays the type of call, pvc,svc,spvc or frf10spvc.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.1 |
mscFrNniDlciVcStateThis attribute displays the state of call control. P5 state is not
supported but is listed for completness. Transitions from one state to
another take very short time. state most often displayed is
dataTransferP4.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.2 |
mscFrNniDlciVcPreviousStateThis attribute displays the previous state of call control. This is a
valuable field to determine how the processing is progressing.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.3 |
mscFrNniDlciVcDiagnosticCodeThis attribute displays the internal substate of call control. It is used
to further refine state of call processing.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.4 |
mscFrNniDlciVcPreviousDiagnosticCodeThis attribute displays the internal substate of call control. It is used
to further refine state of call processing.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.5 |
mscFrNniDlciVcCalledNpiThis attribute displays the Numbering Plan Indicator (NPI) of the
called end.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.6 |
mscFrNniDlciVcCalledDnaThis attribute displays the Data Network Address (Dna) of the
called (destination) DTE to which this call is sent. This address if
defined at recieving end will complete Vc connection.ro DigitString .1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.7 |
mscFrNniDlciVcCalledLcnThis attribute displays the Logical Channel Number of the called
end. It is valid only after both ends of Vc exchanged relevant
information.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.8 |
mscFrNniDlciVcCallingNpiThis attribute displays the Numbering Plan Indicator (NPI) of the
calling end.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.9 |
mscFrNniDlciVcCallingDnaThis attribute displays the Data Network Address (Dna) of the
calling end.ro DigitString .1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.10 |
mscFrNniDlciVcCallingLcnThis attribute displays the Logical Channel Number of the calling
end.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.11 |
mscFrNniDlciVcAccountingEnabledThis attribute indicates that this optional section of accounting
record is suppressed or permitted. If accountingEnabled is yes,
conditions for generation of accounting record were met. These
conditions include billing options, vc recovery conditions and
Module wide accounting data options.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.12 |
mscFrNniDlciVcFastSelectCallThis attribute displays that this is a fast select call.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.13 |
mscFrNniDlciVcPathReliabilityThis attribute displays the path reliability.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.19 |
mscFrNniDlciVcAccountingEndThis attribute indicates if this end should generate an accounting
record. Normally, callingEnd is the end to generate an accounting
record.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.20 |
mscFrNniDlciVcPriorityThis attribute displays whether the call is a normal or a high
priority call.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.21 |
mscFrNniDlciVcSegmentSizeThis attribute displays the segment size (in bytes) used on the call.
It is used to calculate the number of segments transmitted and
received.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.22 |
mscFrNniDlciVcMaxSubnetPktSizeThis attribute indicates the maximum packet size allowed on the Vc.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.27 |
mscFrNniDlciVcRcosToNetworkThis attribute indicates the routing metric routing class of service to
the network.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.28 |
mscFrNniDlciVcRcosFromNetworkThis attribute displays the routing metric Routing Class of Service
from the Network.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.29 |
mscFrNniDlciVcEmissionPriorityToNetworkThis attribute displays the network internal emission priotity to the
network.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.30 |
mscFrNniDlciVcEmissionPriorityFromNetworkThis attribute displays the network internal emission priotity from
the network.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.31 |
mscFrNniDlciVcDataPathThis attribute indicates the data path used by the connection. The
data path is provisioned in Dna and DirectCall components. The
displayed value of this attribute can be different from the
provisioned value.
If the connection is using dprsOnly data path, the string
dprsOnly is displayed. (dynamic packet routing system)
If the connection is using dprsMcsOnly data path, the string
dprsMcsOnly is displayed.
If the connection is using dprsMcsFirst data path, the string
dprsMcsFirst is displayed.ro AsciiString .1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.32 |
mscFrNniDlciVcIntdTableThis group defines display of interval data collected by Vc. Data in
this group is variable and may depend on time when this display
command is issued. SEQUENCE OF MscFrNniDlciVcIntdEntry .1.3.6.1.4.1.562.36.2.1.70.5.3.11 |
mscFrNniDlciVcIntdEntryAn entry in the mscFrNniDlciVcIntdTable. MscFrNniDlciVcIntdEntry .1.3.6.1.4.1.562.36.2.1.70.5.3.11.1 |
mscFrNniDlciVcCallReferenceNumberThis attribute is obsolete. It is replaced by the callReferenceNumber
attribute to display the call reference number in decimal. The
SNMP reference for the callReferenceNumber attribute is
callReferenceNumberDecimal.roobsolete Hex .1.3.6.1.4.1.562.36.2.1.70.5.3.11.1.1 |
mscFrNniDlciVcElapsedTimeTillNowThis attribute displays the elapsed time representing the period of
this interval data. It is elapsed time in 0.1 second increments since
Vc started.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.3.11.1.2 |
mscFrNniDlciVcSegmentsRxThis attribute displays the number of segments received at the time
command was issued. This is the segment received count
maintained by accounting at each end of the Vc. This counter is
updated only when the packet cannot be successfully delivered out
of the sink Vc and to the sink AP Conditions in which packets may
be discarded by the sink Vc include: missing packets due to subnet
discards, segmentation protocol violations due to subnet discard,
duplicated and out-of-ranged packets and packets that arrive while
Vc is in path recovery state.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.3.11.1.3 |
mscFrNniDlciVcSegmentsSentThis attribute displays the number of segments sent at the time
command was issued. This is the segment sent count maintained by
accounting at the source Vc. Vc only counts packets that Vc thinks
can be delivered successfully into the subnet. In reality, these
packets may be dropped by trunking, for instance. This counter is
not updated when splitting fails, when Vc is in a path recovery state,
when packet forwarding fails to forward this packet and when
subsequent packets have to be discarded as we want to minimize the
chance of out-of-sequence and do not intentionally send out-of-
sequenced packets into the subnet.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.3.11.1.4 |
mscFrNniDlciVcStartTimeThis attribute displays the start time of this interval period. If Vc
spans 12 hour time or time of day change startTime reflects new
time as recorded at 12 hour periods or time of day changes.ro EnterpriseDateAndTime .1.3.6.1.4.1.562.36.2.1.70.5.3.11.1.5 |
mscFrNniDlciVcCallReferenceNumberDecimalThis attribute displays the call reference number which is a unique
number generated by the switch.The same Call Reference Number
is stored in the interval data (accounting record) at both ends of the
call. It can be used as one of the attributes in matching duplicate
records generated at each end of the call.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.3.11.1.7 |
mscFrNniDlciVcFrdTableThis group defines Frame Relay attributes collected by Frame Relay
Vc.
The purpose of Vc attributes is to aid end users and verification
people to understand the Vc internal behavior. This is particularly
useful when the network has experienced abnormality and we want
to isolate problems and pinpoint trouble spots.
Attributes are collected on a per Vc basis. Until a need is identified,
statistics are not collected at a processor level. Each attribute is
stored in a 32 bit field and is initialized to zero when a Vc enters
into the data transfer state. When a PVC is disconnected and then
connected again, the attributes will be reset. Attributes cannot be
reset through other methods.
Frame Relay Vc uses a best effort data packet delivery protocol and
a different packet segmentation and combination methods from the
General Vc. The Frame Relay Vc uses the same call setup and
control mechanism (e.g. the support of non-flow control data
packets) as in a General Vc. Most General Vc statistics and internal
variables are used in a Frame Relay Vc and are displayed by
software developers SEQUENCE OF MscFrNniDlciVcFrdEntry .1.3.6.1.4.1.562.36.2.1.70.5.3.12 |
mscFrNniDlciVcFrdEntryAn entry in the mscFrNniDlciVcFrdTable. MscFrNniDlciVcFrdEntry .1.3.6.1.4.1.562.36.2.1.70.5.3.12.1 |
mscFrNniDlciVcFrmCongestedToSubnetThis attribute displays the number of frames from link discarded
due to lack of resources. It keeps track of the number of frames
from link that have to be discarded. The discard reasons include
insufficient memory for splitting the frame into smaller subnet
packet size.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.3.12.1.2 |
mscFrNniDlciVcCannotForwardToSubnetThis attribute displays the number of discarded packets that can not
be forwarded into the subnet because of subnet congestion.
Number of frames from link discarded due to failure in forwarding
a packet from Vc into the subnet.- This attribute is increased when
packet forwarding fails to forward a packet into the subnet. If a
frame is split into multiple subnet packets and a partial packet has
to be discarded, all subsequent partial packets that have not yet been
delivered to the subnet will be discarded as well.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.3.12.1.3 |
mscFrNniDlciVcNotDataXferToSubnetThis attribute records the number of frames from link discarded
when the Vc tries to recover from internal path failure.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.3.12.1.4 |
mscFrNniDlciVcOutOfRangeFrmFromSubnetThis attribute displays the number of frames from subnet discarded
due to out of sequence range for arriving too late.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.3.12.1.5 |
mscFrNniDlciVcCombErrorsFromSubnetThis attribute records the number of subnet packets discarded at the
sink Vc due to the Vc segmentation and combination protocol error.
Usually, this occurs when the subnet discards packets and thus this
statistics can be used to guest the number of subnet packets that are
not delivered to the Vc. It cannot be used as an actual measure
because some subnet packets may have been delivered to Vc but
have to be discarded because these are partial packets to a frame in
which some other partial packets have not been properly delivered
to Vcro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.3.12.1.6 |
mscFrNniDlciVcDuplicatesFromSubnetThis attribute displays the number of subnet packets discarded due
to duplication. Although packets are not retransmitted by the Frame
Relay Vc, it is possible for the subnet to retransmit packets. When
packets are out-of-sequenced and copies of the same packets arrive,
then this attribute is increased.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.3.12.1.7 |
mscFrNniDlciVcNotDataXferFromSubnetThis attribute displays the number of subnet packets discarded when
data transfer is suspended in Vc recovery.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.3.12.1.8 |
mscFrNniDlciVcFrmLossTimeoutsThis attribute displays the number of lost frame timer expiries.
When this count is excessive, the network is very congested and
packets have been discarded in the subnet.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.3.12.1.9 |
mscFrNniDlciVcOoSeqByteCntExceededThis attribute displays the number times that the out of sequence
byte threshold is exceeded. When the threshold is exceeded, this
condition is treated as if the loss frame timer has expired and all
frames queued at the sink Vc are delivered to the AP. We need to
keep this count to examine if the threshold is engineered properly.
This should be used in conjunction with the peak value of out-of-
sequenced queue and the number of times the loss frame timer has
expired. This count should be relatively small when compared with
loss frame timer expiry count.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.3.12.1.10 |
mscFrNniDlciVcPeakOoSeqPktCountThis attribute displays the frame relay peak packet count of the out
of sequence queue. This attribute records the maximum queue
length of the out-of-sequenced queue. The counter can be used to
deduce the message buffer requirement on a Vc.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.3.12.1.11 |
mscFrNniDlciVcPeakOoSeqFrmForwardedThis attribute displays the frame relay peak size of the
sequence packet queue. The subnet may deliver packets out-of-
sequenced. These packets are then queued in an out-of-sequenced
queue, waiting for a packet with the expected sequence number to
come. When that packet arrives, this attribute records the maximum
number of packets that were out-of-sequenced, but now have
become in-sequenced. The statistics is used to measure expected
queue size due to normal subnet packet disorder (not due to subnet
packet discard). Current implementation also uses this statistics to
set a maximum size for the out-of-sequenced queue.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.3.12.1.12 |
mscFrNniDlciVcSendSequenceNumberThis attribute displays the Vc internal packet's send sequence
number. Note that a 'packet' in this context, may be either a user
data packet, or an OAM frame.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.3.12.1.13 |
mscFrNniDlciVcPktRetryTimeoutsThis attribute displays the number of packets which have
retransmission time-outs. When this count is excessive, the network
is very congested and packets have been discarded in the subnet.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.3.12.1.15 |
mscFrNniDlciVcPeakRetryQueueSizeThis attribute displays the peak size of retransmission queue.
This attribute is used as an indicator of the acknowledgment
behavior across the subnet. Records the largest body of
unacknowledged packets.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.3.12.1.16 |
mscFrNniDlciVcSubnetRecoveriesThis attribute displays the number of successful Vc recovery
attempts.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.3.12.1.17 |
mscFrNniDlciVcOoSeqPktCntExceededThis attribute displays the number times that the out of sequence
packet threshold is exceeded. When the threshold is exceeded, this
condition is treated as if the loss frame timer has expired and all
frames queued at the sink Vc are delivered to the AP. We need to
keep this count to examine if the threshold is engineered properly.
This should be used in conjunction with the peak value of out-of-
sequenced queue and the number of times the loss frame timer has
expired. This count should be relatively small when compared with
loss frame timer expiry count.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.3.12.1.19 |
mscFrNniDlciVcPeakOoSeqByteCountThis attribute displays the frame relay peak byte count of the out of
sequence queue. This attribute records the maximum queue length
of the out-of-sequenced queue. The counter can be used to deduce
the message buffer requirement on a Vc.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.3.12.1.20 |
mscFrNniDlciVcDmepTableThis attribute displays the data path used by the connection. Data
path is provisioned in Dna and DirectCall components.
If the connection is using dprsOnly data path, this attribute is
empty.
If the connection is using dprsMcsOnly or dprsMcsFirst data path,
this attribute displays component name of the dprsMcsEndPoint. SEQUENCE OF MscFrNniDlciVcDmepEntry .1.3.6.1.4.1.562.36.2.1.70.5.3.417 |
mscFrNniDlciVcDmepEntryAn entry in the mscFrNniDlciVcDmepTable. MscFrNniDlciVcDmepEntry .1.3.6.1.4.1.562.36.2.1.70.5.3.417.1 |
mscFrNniDlciVcDmepValueThis variable represents both the value and the index for the
mscFrNniDlciVcDmepTable.ro RowPointer .1.3.6.1.4.1.562.36.2.1.70.5.3.417.1.1 |
mscFrNniDlciSp OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.1.70.5.4 |
mscFrNniDlciSpRowStatusTableThis entry controls the addition and deletion of
mscFrNniDlciSp components. SEQUENCE OF MscFrNniDlciSpRowStatusEntry .1.3.6.1.4.1.562.36.2.1.70.5.4.1 |
mscFrNniDlciSpRowStatusEntryA single entry in the table represents a single
mscFrNniDlciSp component. MscFrNniDlciSpRowStatusEntry .1.3.6.1.4.1.562.36.2.1.70.5.4.1.1 |
mscFrNniDlciSpRowStatusThis variable is used as the basis for SNMP naming of
mscFrNniDlciSp components.
These components cannot be added nor deleted.ro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.5.4.1.1.1 |
mscFrNniDlciSpComponentNameThis variable provides the component's string name for
use with the ASCII Console Interfacero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.5.4.1.1.2 |
mscFrNniDlciSpStorageTypeThis variable represents the storage type value for the
mscFrNniDlciSp tables.ro StorageType (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.5.4.1.1.4 |
mscFrNniDlciSpIndexThis variable represents the index for the mscFrNniDlciSp tables. NonReplicated .1.3.6.1.4.1.562.36.2.1.70.5.4.1.1.10 |
mscFrNniDlciSpParmsTableThis group contains the provisionable attributes for the Data Link
Connection Identifier. These attributes reflect the service parameters
specific to this instance of DLCI . The congestion control attributes
in this group are defined in T1.606 Addendum 1. SEQUENCE OF MscFrNniDlciSpParmsEntry .1.3.6.1.4.1.562.36.2.1.70.5.4.11 |
mscFrNniDlciSpParmsEntryAn entry in the mscFrNniDlciSpParmsTable. MscFrNniDlciSpParmsEntry .1.3.6.1.4.1.562.36.2.1.70.5.4.11.1 |
mscFrNniDlciSpMaximumFrameSizeThis attribute specifies the maximum number of octets which may
be included in the information field. The frame relay header and
CRC octets are not included in this definition. This attribute
corresponds to the dN1 parameter described in the Vendor Forum
Specification.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.4.11.1.1 |
mscFrNniDlciSpRateEnforcementThis attribute specifies whether rate enforcement is in effect for this
user Data Link Connection on this Frame Relay interface. Turning
on rate enforcement means that CIR and DE=1 traffic will be
measured and enforced. Turning off rate enforcement means that all
frames from the user will be accepted and no modifications to the
frame with respect to the DE bit will be made.rw Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.4.11.1.2 |
mscFrNniDlciSpCommittedInformationRateThis attribute specifies the committed information rate (CIR) in bits
per second (bit/s). When rateEnforcement is set to on, cir is the rate
at which the network agrees to transfer information under normal
conditions. This rate is measured over a measurement interval (t)
that is determined internally based on CIR and the committed burst
size (Bc). An exception to this occurs when CIR is provisioned to
be zero, in which case the measurement interval (t) must be
provisioned explicitly.
This attribute is ignored when rateEnforcement is off. If
rateEnforcement is on and this attribute is 0, Bc must also be 0.rw Gauge32 .1.3.6.1.4.1.562.36.2.1.70.5.4.11.1.3 |
mscFrNniDlciSpCommittedBurstSizeThis attribute specifies the committed burst size (Bc) in bits. bc is
the amount of data that a network agrees to transfer under normal
conditions over a measurement interval (t). Data marked DE=1 is
not accounted for in Bc.
This attribute is ignored when rateEnforcement is off. If
rateEnforcement is on and this attribute is 0, cir must also be 0.rw Gauge32 .1.3.6.1.4.1.562.36.2.1.70.5.4.11.1.4 |
mscFrNniDlciSpExcessBurstSizeThis attribute specifies the excess burst size (Be) in bits. Be is the
amount of uncommitted data that the network will attempt to deliver
over measurement interval T. Data marked DE=1 by the user or by
the network is accounted for here.
CIR, Bc, and Be cannot all be zero when rateEnforcement is on.rw Gauge32 .1.3.6.1.4.1.562.36.2.1.70.5.4.11.1.5 |
mscFrNniDlciSpMeasurementIntervalWhen cir and bc are zero and rateEnforcement is on, this attribute
must be provisioned to specify the time interval (in milliseconds)
over which rates and burst sizes are measured.
When cir and bc are non-zero, the time interval is internally
calculated and is not shown. In that situation, this field is ignored,
and is not representative of the time interval.
This attribute is ignored when rateEnforcement is off, or when cir
and bc are non-zero. If rateEnforcement is on and both cir and bc
are zero, this field must be non-zero.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.4.11.1.6 |
mscFrNniDlciSpRateAdaptationThis attribute specifies whether rate adaptation is in effect for this
user Data Link Connection on this Frame Relay interface. Rate
adaptation is a feature that, in periods of congestion, adapts the rate
at which the user is allowed to send data into the network to that
which the network is able to handle at that time. This pro-active
measure of handling congestion optimizes network resources by
causing the ingress to discard frames that would otherwise be
discarded in the network.
If this attribute is set to on, then, at the onset of congestion, the
excess information rate (EIR) is reduced to a very low rate. If
congestion persists, then the allowed CIR is reduced geometrically
by 25% of the current value at that time. The minimum to which
CIR can be reduced is 1/16th (6.25%) of the provisioned value. As
congestion alleviates, CIR is increased linearly by 6.25% of the
provisioned value specified in committedInformationRate.
If set to eirOnly, then rate adaptation will only apply to the excess
information rate (EIR). At the onset of congestion, the allowed EIR
is reduced by 25% of its provisioned value. If congestion persists,
EIR is reduced geometrically by 25% of the current value at that
time. As congestion alleviates, EIR is gradually increased linearly
by 6.25% of the provisioned EIR.
If set to cirProportionate, then rate adaptation will also only apply
to the excess information rate (EIR). At the onset of congestion the
initial allowed EIR is set to a multiple of the provisioned CIR. If
congestion persists, the allowed EIR is reduced geometrically by
25% of the current value at that time. As congestion alleviates, EIR
is gradually increased linearly by 6.25% of the provisioned EIR.
Note that the allowed EIR may be set higher than the provisioned
EIR, since it is calculated initially using another parameter, the
provisioned CIR. If the allowed EIR at the moment is higher than
the provisioned EIR, then the provisioned EIR is used instead.
This attribute can only be set to on eirOnly or cirProportionate if
rateEnforcement is turned on.rw Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.4.11.1.7 |
mscFrNniDlciSpAccountingThis attribute specifies whether accounting data collection and
record generation is turned on at this DLCI. For accounting data
collection and record generation to be turned on, the accountingOn
bit and at least one of the accountCollection bits in the
DataNetworkAddress component must be set to on.rw Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.4.11.1.8 |
mscFrNniDlciSpRaSensitivityThis attribute specifies the sensitivity of the rate adaptation system.
A higher number indicates a higher sensitivity and therefore a
quicker reaction time to network conditions. A quicker reaction
time allows the network to discard frames at the access and protect
network resources, but can lead to false alarms and a greater
fluctuation of the allowed rate. A higher setting therefore tends to
favour the protection of the network over the allowed throughput of
the user.
A lower number indicates a lower sensitivity and therefore a slower
reaction to network conditions. A slower reaction time results in a
greater amount of user traffic allowed into the network, but can lead
to a waste of network bandwidth since the traffic may be discarded
at the congested resource. A lower setting therefore tends to favour
the allowed throughput of the user over the protection of the
network.
This attribute is applicable for adapting EIR when rateAdaptation is
eirOnly or cirProportionate, or CIR when rateAdaptation is on.
This attribute is ignored if rateAdaptation is turned off.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.4.11.1.9 |
mscFrNniDlciSpUpdateBCIThis attribute specifies whether internal Backward Congestion
Indication (BCI) bits will report congestion external to the Passport
network, as communicated through incoming BECN bits.
If updateBCI is set to on, then BCI bits for incoming frames will be
set if the BECN on the frame is set. If updatBCI is set to off, then
incoming BECN bits will have no effect.
Setting updateBCI on for a DLCI means that the remote end of the
DLCI, which is specified by the remotedna and remotedlci attributes
of the dc component of the dlci, may perform Rate Adaptation
using the flow of incoming BECN bits, in addition to internal
Passport congestion management systems.
If the rateAdaptation attribute of the remote dlci is provisioned as
eirOnly, cirProportionate, or on, then congestion from another
network connected to a Passport network may trigger dynamic
congestion management. If the rateAdaptation attribute of the
remote dlci is provisioned to off, then the setting of updateBCI
attribute here will have no effect..rw Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.4.11.1.10 |
mscFrNniDlciLb OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.1.70.5.5 |
mscFrNniDlciLbRowStatusTableThis entry controls the addition and deletion of
mscFrNniDlciLb components. SEQUENCE OF MscFrNniDlciLbRowStatusEntry .1.3.6.1.4.1.562.36.2.1.70.5.5.1 |
mscFrNniDlciLbRowStatusEntryA single entry in the table represents a single
mscFrNniDlciLb component. MscFrNniDlciLbRowStatusEntry .1.3.6.1.4.1.562.36.2.1.70.5.5.1.1 |
mscFrNniDlciLbRowStatusThis variable is used as the basis for SNMP naming of
mscFrNniDlciLb components.
These components cannot be added nor deleted.ro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.5.5.1.1.1 |
mscFrNniDlciLbComponentNameThis variable provides the component's string name for
use with the ASCII Console Interfacero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.5.5.1.1.2 |
mscFrNniDlciLbStorageTypeThis variable represents the storage type value for the
mscFrNniDlciLb tables.ro StorageType (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.5.5.1.1.4 |
mscFrNniDlciLbIndexThis variable represents the index for the mscFrNniDlciLb tables. NonReplicated .1.3.6.1.4.1.562.36.2.1.70.5.5.1.1.10 |
mscFrNniDlciLbStatsTableThis group contains all the statistics for the data loopback tool. SEQUENCE OF MscFrNniDlciLbStatsEntry .1.3.6.1.4.1.562.36.2.1.70.5.5.10 |
mscFrNniDlciLbStatsEntryAn entry in the mscFrNniDlciLbStatsTable. MscFrNniDlciLbStatsEntry .1.3.6.1.4.1.562.36.2.1.70.5.5.10.1 |
mscFrNniDlciLbLocalTotalFrmThis attribute records the number of frames looped back to the link
since loopback was last started.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.5.10.1.1 |
mscFrNniDlciLbLocalTotalBytesThis attribute records the number of bytes looped back to the link
since loopback mode was started.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.5.10.1.2 |
mscFrNniDlciLbLocalFecnFrmThis attribute records the number of frames with the Forward
Explicit Congestion Notification (FECN) bit set, looped back to the
link since the loopback mode was started.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.5.10.1.3 |
mscFrNniDlciLbLocalBecnFrmThis attribute records the number of frames with the Backward
Explicit Congestion Notification (BECN) bit set, looped back to the
link since the loopback mode was started.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.5.10.1.4 |
mscFrNniDlciLbLocalDeFrmThis attribute records the number of frames with the Discard
Eligibility (DE) bit set, looped back to the link since the loopback
mode was started.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.5.10.1.5 |
mscFrNniDlciLbLocalDeBytesThis attribute records the number of bytes in frames with the
Discard Eligibility (DE) bit set, looped back to the link since the
loopback mode was started.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.5.10.1.6 |
mscFrNniDlciLbRemoteTotalFrmThis attribute records the number of frames looped back to the
subnet since loopback was last started.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.5.10.1.7 |
mscFrNniDlciLbRemoteTotalBytesThis attribute records the number of bytes looped back to the subnet
since loopback was last started.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.5.10.1.8 |
mscFrNniDlciLbRemoteFecnFrmThis attribute records the number of frames with the Forward
Explicit Congestion Notification (FECN) bit set, looped back to the
subnet since the loopback mode was started.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.5.10.1.9 |
mscFrNniDlciLbRemoteBecnFrmThis attribute records the number of frames with the Backward
Explicit Congestion Notification (BECN) bit set, looped back to the
subnet since the loopback mode was started.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.5.10.1.10 |
mscFrNniDlciLbRemoteDeFrmThis attribute records the number of frames with the Discard
Eligibility (DE) bit set, looped back to the subnet since the
loopback mode was started.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.5.10.1.13 |
mscFrNniDlciLbRemoteDeBytesThis attribute records the number of bytes in frames with the
Discard Eligibility (DE) bit set, looped back to the subnet since the
loopback mode was started.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.5.10.1.14 |
mscFrNniDlciEgressSp OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.1.70.5.6 |
mscFrNniDlciEgressSpRowStatusTableThis entry controls the addition and deletion of
mscFrNniDlciEgressSp components. SEQUENCE OF MscFrNniDlciEgressSpRowStatusEntry .1.3.6.1.4.1.562.36.2.1.70.5.6.1 |
mscFrNniDlciEgressSpRowStatusEntryA single entry in the table represents a single
mscFrNniDlciEgressSp component. MscFrNniDlciEgressSpRowStatusEntry .1.3.6.1.4.1.562.36.2.1.70.5.6.1.1 |
mscFrNniDlciEgressSpRowStatusThis variable is used as the basis for SNMP naming of
mscFrNniDlciEgressSp components.
These components cannot be added nor deleted.ro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.5.6.1.1.1 |
mscFrNniDlciEgressSpComponentNameThis variable provides the component's string name for
use with the ASCII Console Interfacero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.5.6.1.1.2 |
mscFrNniDlciEgressSpStorageTypeThis variable represents the storage type value for the
mscFrNniDlciEgressSp tables.ro StorageType (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.5.6.1.1.4 |
mscFrNniDlciEgressSpIndexThis variable represents the index for the mscFrNniDlciEgressSp tables. NonReplicated .1.3.6.1.4.1.562.36.2.1.70.5.6.1.1.10 |
mscFrNniDlciEgressSpProvTableThis group contains the provisionable attributes for this component. SEQUENCE OF MscFrNniDlciEgressSpProvEntry .1.3.6.1.4.1.562.36.2.1.70.5.6.10 |
mscFrNniDlciEgressSpProvEntryAn entry in the mscFrNniDlciEgressSpProvTable. MscFrNniDlciEgressSpProvEntry .1.3.6.1.4.1.562.36.2.1.70.5.6.10.1 |
mscFrNniDlciEgressSpCommittedInformationRateThis attribute specifies the committed information rate (CIR) for the
egress direction. It is used for Call Admission Control (CAC) at the
egress link.
If the value is set to sameAsSp, the value of this attribute is the
same as the committedInformationRate attribute under the
ServiceParameters component.
VALUES (
50000001 = sameAsServiceParameters
)rw Unsigned32 (0..50000000 | 50000001) .1.3.6.1.4.1.562.36.2.1.70.5.6.10.1.1 |
mscFrNniDlciEgressSpCommittedBurstSizeThis attribute specifies the committed burst size (Bc) for the egress
direction. It is used for performing Call Admission Control (CAC)
at the egress link.
If the value is set to sameAsSp, the value of this attribute is the
same as the committedBurstSize attribute under the
ServiceParameters component.
VALUES (
50000001 = sameAsServiceParameters
)rw Unsigned32 (0..50000000 | 50000001) .1.3.6.1.4.1.562.36.2.1.70.5.6.10.1.2 |
mscFrNniDlciEgressSpExcessBurstSizeThis attribute specifies the excess burst size (Be) for the egress
direction. It is used for Call Admission Control (CAC) function
towards the egress link.
If the value is set to sameAsSp, the value of this attribute is the
same as the excessBurstSize attribute under the ServiceParameters
component.
VALUES (
50000001 = sameAsServiceParameters
)rw Unsigned32 (0..50000000 | 50000001) .1.3.6.1.4.1.562.36.2.1.70.5.6.10.1.3 |
mscFrNniDlciEgressSpMeasurementIntervalThis attribute specifies the time interval over which rates and burst
sizes are measured in the egress direction. It is used for bandwidth
reservation for Call Admission Control (CAC) towards the egress
link.
If the value is set to sameAsSp, the value of this attribute is the
same as the measurementInterval attribute under the
ServiceParameters component.
VALUES (
25501 = sameAsServiceParameters
)rw Unsigned32 (0..25500 | 25501) .1.3.6.1.4.1.562.36.2.1.70.5.6.10.1.4 |
mscFrNniDlciStateTableThis group contains the three OSI State attributes and the six OSI
Status attributes. The descriptions generically indicate what each
attribute implies about the component. Note that not all the values
and state combinations described here are supported by every
component which uses this group. For component-specific
information and the valid state combinations, refer to NTP 241-
7001-150, Passport Operations and Maintenance Guide. SEQUENCE OF MscFrNniDlciStateEntry .1.3.6.1.4.1.562.36.2.1.70.5.10 |
mscFrNniDlciStateEntryAn entry in the mscFrNniDlciStateTable. MscFrNniDlciStateEntry .1.3.6.1.4.1.562.36.2.1.70.5.10.1 |
mscFrNniDlciAdminStateThis attribute indicates the OSI Administrative State of the
component.
The value locked indicates that the component is administratively
prohibited from providing services for its users. A Lock or Lock -
force command has been previously issued for this component.
When the value is locked, the value of usageState must be idle.
The value shuttingDown indicates that the component is
administratively permitted to provide service to its existing users
only. A Lock command was issued against the component and it is
in the process of shutting down.
The value unlocked indicates that the component is administratively
permitted to provide services for its users. To enter this state, issue
an Unlock command to this component.
The OSI Status attributes, if supported by the component, may
provide more details, qualifying the state of the component.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.10.1.1 |
mscFrNniDlciOperationalStateThis attribute indicates the OSI Operational State of the component.
The value enabled indicates that the component is available for
operation. Note that if adminState is locked, it would still not be
providing service.
The value disabled indicates that the component is not available for
operation. For example, something is wrong with the component
itself, or with another component on which this one depends. If the
value is disabled, the usageState must be idle.
The OSI Status attributes, if supported by the component, may
provide more details, qualifying the state of the component.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.10.1.2 |
mscFrNniDlciUsageStateThis attribute indicates the OSI Usage State of the component.
The value idle indicates that the component is not currently in use.
The value active indicates that the component is in use and has
spare capacity to provide for additional users.
The value busy indicates that the component is in use and has no
spare operating capacity for additional users at this time.
The OSI Status attributes, if supported by the component, may
provide more details, qualifying the state of the component.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.10.1.3 |
mscFrNniDlciAvailabilityStatusIf supported by the component, this attribute indicates the OSI
Availability status of the component. Note that, even though it is
defined as a multi-valued set, at most one value is shown to the user.
When no values are in the set, this indicates that either the attribute
is not supported or that none of the status conditions described
below are present.
The value inTest indicates that the resource is undergoing a test
procedure. If adminState is locked or shuttingDown, the normal
users are precluded from using the resource and controlStatus is
reservedForTest. Tests that do not exclude additional users can be
present in any operational or administrative state but the
reservedForTest condition should not be present.
The value failed indicates that the component has an internal fault
that prevents it from operating. The operationalState is disabled.
The value dependency indicates that the component cannot operate
because some other resource on which it depends is unavailable.
The operationalState is disabled.
The value powerOff indicates the resource requires power to be
applied and it is not powered on. The operationalState is disabled.
The value offLine indicates the resource requires a routine
operation (either manual, automatic, or both) to be performed to
place it on-line and make it available for use. The operationalState
is disabled.
The value offDuty indicates the resource is inactive in accordance
with a predetermined time schedule. In the absence of other
disabling conditions, the operationalState is enabled or disabled.
The value degraded indicates the service provided by the
component is degraded in some way, such as in speed or operating
capacity. However, the resource remains available for service. The
operationalState is enabled.
The value notInstalled indicates the resource is not present. The
operationalState is disabled.
The value logFull is not used.
Description of bits:
inTest(0)
failed(1)
powerOff(2)
offLine(3)
offDuty(4)
dependency(5)
degraded(6)
notInstalled(7)
logFull(8)ro OCTET STRING .1.3.6.1.4.1.562.36.2.1.70.5.10.1.4 |
mscFrNniDlciProceduralStatusIf supported by the component, this attribute indicates the OSI
Procedural status of the component. Note that, even though it is
defined as a multi-valued set, at most one value is shown to the user.
When no values are in the set, this indicates that either the attribute
is not supported or that none of the status conditions described
below are present.
The value initializationRequired indicates (for a resource which
doesn't initialize autonomously) that initialization is required before
it can perform its normal functions, and this procedure has not been
initiated. The operationalState is disabled.
The value notInitialized indicates (for a resource which does
initialize autonomously) that initialization is required before it can
perform its normal functions, and this procedure has not been
initiated. The operationalState may be enabled or disabled.
The value initializing indicates that initialization has been initiated
but is not yet complete. The operationalState may be enabled or
disabled.
The value reporting indicates the resource has completed some
processing operation and is notifying the results. The
operationalState is enabled.
The value terminating indicates the component is in a termination
phase. If the resource doesn't reinitialize autonomously,
operationalState is disabled; otherwise it is enabled or disabled.
Description of bits:
initializationRequired(0)
notInitialized(1)
initializing(2)
reporting(3)
terminating(4)ro OCTET STRING .1.3.6.1.4.1.562.36.2.1.70.5.10.1.5 |
mscFrNniDlciControlStatusIf supported by the component, this attribute indicates the OSI
Control status of the component. Note that, even though it is defined
as a multi-valued set, at most one value is shown to the user.
When no values are in the set, this indicates that either the attribute
is not supported or that none of the status conditions described
below are present.
The value subjectToTest indicates the resource is available but tests
may be conducted simultaneously at unpredictable times, which
may cause it to exhibit unusual characteristics.
The value partOfServicesLocked indicates that part of the service is
restricted from users of a resource. The adminState is unlocked.
The value reservedForTest indicates that the component is
administratively unavailable because it is undergoing a test
procedure. The adminState is locked.
The value suspended indicates that the service has been
administratively suspended.
Description of bits:
subjectToTest(0)
partOfServicesLocked(1)
reservedForTest(2)
suspended(3)ro OCTET STRING .1.3.6.1.4.1.562.36.2.1.70.5.10.1.6 |
mscFrNniDlciAlarmStatusIf supported by the component, this attribute indicates the OSI
Alarm status of the component. Note that, even though it is defined
as a multi-valued set, at most one value is shown to the user.
When no values are in the set, this indicates that either the attribute
is not supported or that none of the status conditions described
below are present.
The value underRepair indicates the component is currently being
repaired. The operationalState is enabled or disabled.
The value critical indicates one or more critical alarms are
outstanding against the component. Other, less severe, alarms may
also be outstanding. The operationalState is enabled or disabled.
The value major indicates one or more major alarms are
outstanding against the component. Other, less severe, alarms may
also be outstanding. The operationalState is enabled or disabled.
The value minor indicates one or more minor alarms are
outstanding against the component. Other, less severe, alarms may
also be outstanding. The operationalState is enabled or disabled.
The value alarmOutstanding generically indicates that an alarm of
some severity is outstanding against the component.
Description of bits:
underRepair(0)
critical(1)
major(2)
minor(3)
alarmOutstanding(4)ro OCTET STRING .1.3.6.1.4.1.562.36.2.1.70.5.10.1.7 |
mscFrNniDlciStandbyStatusIf supported by the component, this attribute indicates the OSI
Standby status of the component.
The value notSet indicates that either the attribute is not supported
or that none of the status conditions described below are present.
Note that this is a non-standard value, used because the original
specification indicated this attribute was set-valued and thus, did not
provide a value to indicate that none of the other three are
applicable.
The value hotStandby indicates that the resource is not providing
service but will be immediately able to take over the role of the
resource to be backed up, without initialization activity, and
containing the same information as the resource to be backed up.
The value coldStandby indicates the resource is a backup for
another resource but will not be immediately able to take over the
role of the backed up resource and will require some initialization
activity.
The value providingService indicates that this component, as a
backup resource, is currently backing up another resource.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.10.1.8 |
mscFrNniDlciUnknownStatusThis attribute indicates the OSI Unknown status of the component.
The value false indicates that all of the other OSI State and Status
attribute values can be considered accurate.
The value true indicates that the actual state of the component is not
known for sure.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.10.1.9 |
mscFrNniDlciAbitTableThis group contains the A-Bit status information for this Data Link
Connection Identifier. SEQUENCE OF MscFrNniDlciAbitEntry .1.3.6.1.4.1.562.36.2.1.70.5.12 |
mscFrNniDlciAbitEntryAn entry in the mscFrNniDlciAbitTable. MscFrNniDlciAbitEntry .1.3.6.1.4.1.562.36.2.1.70.5.12.1 |
mscFrNniDlciABitStatusToIfThis attribute is the most recent A-bit status sent to the interface.
The A-bit status is part of the LMI protocol, and indicates
willingness to accept data from the local interface.
inactive - the Frame Relay service discards all data offered from the
local interface.
active - the Frame Relay service tries to process all data offered
from the local interface.
notApplicable - the DLCI is switched, so this attribute is ignored.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.12.1.1 |
mscFrNniDlciABitReasonToIfThis attribute provides the reason (if any) for an inactive status to
be sent to the interface. This reason is notApplicable for an active
status.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.12.1.2 |
mscFrNniDlciABitStatusFromIfThis attribute is the most recent A-Bit status received from the
interface.
inactive - the Frame Relay service informs the remote DLCI not to
send user data to this interface.
active - the Frame Relay service informs the remote DLCI that it is
okay to send user data to this interface.
notApplicable - the DLCI is switched, so this attribute is ignored.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.12.1.3 |
mscFrNniDlciABitReasonFromIfThis attribute provides the reason (if any) for an inactive status to
be sent to the subnet. This reason is notApplicable for an active
status.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.12.1.4 |
mscFrNniDlciLoopbackStateThis attribute has the value on when the DLCI is in loopback mode
and off otherwise. The loopback command verbs start and stop are
used to initiate and terminate the loopback mode for a DLCI. While
loopbackState is on, the local LMI will report to the interface the A-
bit status as active. Also an active A-bit signal will be reliably
propagated across the subnet to the remote DLCI.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.12.1.5 |
mscFrNniDlciSpOpTableThis group defines the service and traffic parameters specific to this
instance of DLCI. In the case of permanent (PVC and P-SPVC)
DLCIs, the values of attributes with the exception of the
measurementInterval reflect the provisioning under the FrNni Dlci
Sp component. In the case of switched (SVC and S-SPVC) DLCIs,
the values of attributes reflect the service parameter negotiations
between what is provisioned under the FrNni Sig component and
the signaled parameters. SEQUENCE OF MscFrNniDlciSpOpEntry .1.3.6.1.4.1.562.36.2.1.70.5.13 |
mscFrNniDlciSpOpEntryAn entry in the mscFrNniDlciSpOpTable. MscFrNniDlciSpOpEntry .1.3.6.1.4.1.562.36.2.1.70.5.13.1 |
mscFrNniDlciMaximumFrameSizeThis attribute indicates the maximum number of octets which may
be included in the information field. The frame relay header and
CRC octets are not included in this definition. This attribute
corresponds to the dN1 parameter described in the Vendor Forum
Specification.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.13.1.1 |
mscFrNniDlciRateEnforcementThis attribute is obsolete. It provided the information which is now
represented by the provisionable attribute rateEnforcement under
the ServiceParameters component.roobsolete Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.13.1.2 |
mscFrNniDlciCommittedInformationRateThis attribute indicates the committed information rate (CIR) in bits
per second (bit/s). When rateEnforcement is set to on, cir is the rate
at which the network agrees to transfer information under normal
conditions. This rate is measured over a measurement interval (t)
that is determined internally based on CIR and the committed burst
size (Bc). An exception to this occurs when CIR is provisioned to
be zero, in which case the measurement interval (t) must be
provisioned explicitly.
This attribute should be ignored when rateEnforcement is off.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.13.1.3 |
mscFrNniDlciCommittedBurstSizeThis attribute indicates the committed burst size (Bc) in bits. bc is
the amount of data that a network agrees to transfer under normal
conditions over a measurement interval (t). Data marked DE=1 is
not accounted for in Bc.
This attribute should be ignored when rateEnforcement is off.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.13.1.4 |
mscFrNniDlciExcessBurstSizeThis attribute indicates the excess burst size (Be) in bits. Be is the
amount of uncommitted data that the network will attempt to deliver
over measurement interval T. Data marked DE=1 by the user or by
the network is accounted for here.
This attribute should be ignored when rateEnforcement is off.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.13.1.5 |
mscFrNniDlciMeasurementIntervalThis attribute indicates the time interval (in milliseconds) over
which rates and burst sizes are measured.
This attribute should be ignored when rateEnforcement is off.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.13.1.6 |
mscFrNniDlciRateAdaptationThis attribute is obsolete. It provided the information which is now
represented by the provisionable attribute rateAdaptation under the
ServiceParameters component.roobsolete Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.13.1.7 |
mscFrNniDlciAccountingThis attribute indicates whether accounting data collection and
record generation is turned on at this DLCI. For accounting data
collection and record generation to be turned on, the accountingOn
bit and at least one of the accountCollection bits in the
DataNetworkAddress component must be set to on.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.13.1.8 |
mscFrNniDlciEmissionPriorityToIfThis attribute indicates the emission priority of frames sent to the
interface. A larger value denotes a higher priority.ro INTEGER (0 | 1 | 2 | 3) .1.3.6.1.4.1.562.36.2.1.70.5.13.1.9 |
mscFrNniDlciTransferPriToNwkThis attribute indicates the priority at which data is transferred to
the network.
The transfer priority is a preference configured for an application
according to its delay-sensitivity requirement. Frames with higher
transfer priority are served by the network before the frames with
lower priority. The transfer priority standard is defined to have 16
indices from 0 to 15.
Each transfer priority n, where n specifies the transfer priority
index, contains a default setting for routing class of service
(multimedia, delay, or throughput) and frame relay egress queue
(depending on the number of supported egress queues on the remote
end interface) specified by the routingClassOfService and
emissionPriority attributes provisioned in the Mod Frs DprsNet
Tpm/n component. The default mapping can be altered by a user if
required.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.13.1.10 |
mscFrNniDlciTransferPriFromNwkThis attribute indicates the priority at which data is transferred from
the network.
The transfer priority is a preference configured for an application
according to its delay-sensitivity requirement. Frames with higher
transfer priority are served by the network before the frames with
lower priority. The transfer priority standard is defined to have 16
indices from 0 to 15.
Each transfer priority n, where n specifies the transfer priority
index, contains a default setting for routing class of service
(multimedia, delay, or throughput) and frame relay egress queue
(depending on the number of supported egress queues on the remote
end interface) specified by the routingClassOfService and
emissionPriority attributes provisioned in the Mod Frs DprsNet
Tpm/n component. The default mapping can be altered by a user if
required.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.13.1.11 |
mscFrNniDlciStatsTableThis group contains the operational statistics for the Frame Relay
Data Link Connection Identifier. SEQUENCE OF MscFrNniDlciStatsEntry .1.3.6.1.4.1.562.36.2.1.70.5.14 |
mscFrNniDlciStatsEntryAn entry in the mscFrNniDlciStatsTable. MscFrNniDlciStatsEntry .1.3.6.1.4.1.562.36.2.1.70.5.14.1 |
mscFrNniDlciFrmToIfThis attribute counts the frames sent out the interface. When the
maximum count is reached the count wraps to zero.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.14.1.1 |
mscFrNniDlciFecnFrmToIfThis attribute counts the frames sent to the interface with the
Forward Explicit Congestion Notification (FECN) bit set. When the
count reaches maximum it wraps to zero.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.14.1.2 |
mscFrNniDlciBecnFrmToIfThis attribute counts the frames sent to the interface with the
Backward Explicit Congestion Notification (BECN) bit set. When
the count reaches maximum it wraps to zero.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.14.1.3 |
mscFrNniDlciBciToSubnetThis attribute counts the frames sent into the local network with the
Backward Congestion Indication (BCI) bit set. When the count
reaches maximum it wraps to zero.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.14.1.4 |
mscFrNniDlciDeFrmToIfThis attribute counts the frames sent to the interface with the
Discard Eligibility (DE) bit set. When the count reaches maximum
it wraps to zero.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.14.1.5 |
mscFrNniDlciDiscCongestedToIfThis attribute counts the number of frame discards at the Frame
Relay service due to local congestion in the direction toward the
interface. When this count reaches maximum, it wraps to zero.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.14.1.6 |
mscFrNniDlciDiscDeCongestedToIfThis attribute counts the number of discarded frames, with the
Discard Eligibility (DE) bit set, at the Frame Relay service, due to
local congestion in the direction toward the interface. When this
count reaches maximum, it wraps to zero.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.14.1.7 |
mscFrNniDlciFrmFromIfThis attribute counts the frames received from the interface. It
includes the frames that are discarded due to error or excess. When
the maximum count is reached the count wraps to zero.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.14.1.8 |
mscFrNniDlciFecnFrmFromIfThis attribute counts the frames received from the interface with the
Forward Explicit Congestion Notification (FECN) bit set. When the
count reaches maximum it wraps to zero.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.14.1.9 |
mscFrNniDlciBecnFrmFromIfThis attribute counts the frames received from the interface with the
Backward Explicit Congestion Notification (BECN) bit set. When
the count reaches maximum it wraps to zero.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.14.1.10 |
mscFrNniDlciFciFromSubnetThis attribute counts the frames received from the network with the
Forward Congestion Indication (FCI) bit set. When the count
reaches maximum it wraps to zero.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.14.1.11 |
mscFrNniDlciBciFromSubnetThis attribute counts the frames received from the network with the
Backward Congestion Indication (BCI) bit set. When the count
reaches maximum it wraps to zero.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.14.1.12 |
mscFrNniDlciDeFrmFromIfThis attribute counts the frames received from the interface with the
Discard Eligibility (DE) bit set. When the count reaches maximum
it wraps to zero.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.14.1.13 |
mscFrNniDlciExcessFrmFromIfThis attribute counts the frames received from the interface with the
Discard Eligibility (DE) bit clear, but subsequently set by the
network due to rate enforcement. When the count reaches
maximum it wraps to zero.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.14.1.14 |
mscFrNniDlciDiscExcessFromIfThis attribute counts the frames which were discarded due to rate
enforcement. When the count reaches maximum it wraps to zero.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.14.1.15 |
mscFrNniDlciDiscFrameAbitThis attribute counts the number of frame discards at the Frame
Relay Service, due to an inactive PVC status, in the direction
toward the local network. When this count reaches maximum, it
wraps to zero.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.14.1.16 |
mscFrNniDlciDiscCongestedFromIfThis attribute counts the number of frame discards at the Frame
Relay service due to local congestion in the direction toward the
network. When this count reaches maximum, it wraps to zero.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.14.1.17 |
mscFrNniDlciDiscDeCongestedFromIfThis attribute counts the number of discarded frames, with the
Discard Eligibility (DE) bit set, at the Frame Relay service, due to
local congestion, in the direction toward the local network. When
this count reaches maximum, it wraps to zero.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.14.1.18 |
mscFrNniDlciErrorShortFrmFromIfThis attribute counts the frames received with 0 octets in the
information field. When the count reaches maximum it wraps to
zero.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.14.1.19 |
mscFrNniDlciErrorLongFrmFromIfThis attribute counts the frames received with number of octets in
the information field greater than the subscribed maximum. When
the count reaches maximum it wraps to zero. Frames whose lengths
are greater than the hardware receive buffer are ignored by the
hardware and are therefore not included in this count.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.14.1.20 |
mscFrNniDlciBecnFrmSetByServiceThis attribute counts the number of frames with BECN set by the
Frame Relay service. It is incremented whenever the Frame Relay
service sets BECN on a frame upon detecting local congestion. This
count is incremented regardless of whether the frame already bears
a set BECN bit since its use is to determine the place of congestion.
When the count reaches maximum, it wraps to zero.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.14.1.21 |
mscFrNniDlciBytesToIfThis attribute counts the bytes sent out the interface. When the
maximum count is reached the count wraps to zero.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.14.1.22 |
mscFrNniDlciDeBytesToIfThis attribute counts the bytes sent to the interface with the Discard
Eligibility (DE) bit set. When the count reaches maximum it wraps
to zero.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.14.1.23 |
mscFrNniDlciDiscCongestedToIfBytesThis attribute counts the number of byte discards at the Frame
Relay service due to local congestion in the direction toward the
link. When this count reaches maximum, it wraps to zero.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.14.1.24 |
mscFrNniDlciDiscDeCongestedToIfBytesThis attribute counts the number of discard eligible (DE=1) byte
discards at the Frame Relay service due to local congestion in the
direction toward the link. When the maximum count is reached the
count wraps to zero.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.14.1.25 |
mscFrNniDlciBytesFromIfThis attribute counts the bytes received from the interface. Bytes
that are discarded due to error or excess are not counted. When the
maximum count is reached the count wraps to zero.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.14.1.26 |
mscFrNniDlciDeBytesFromIfThis attribute counts the bytes received from the interface with the
Discard Eligibility (DE) bit set. When the count reaches maximum
it wraps to zero.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.14.1.27 |
mscFrNniDlciExcessBytesFromIfThis attribute counts the bytes received from the interface with the
Discard Eligibility (DE) bit clear, but subsequently set by the
network due to rate enforcement. When the count reaches
maximum it wraps to zero.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.14.1.28 |
mscFrNniDlciDiscExcessFromIfBytesThis attribute counts the bytes which were discarded due to rate
enforcement. When the count reaches maximum it wraps to zero.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.14.1.29 |
mscFrNniDlciDiscByteAbitThis attribute counts the bytes which were discarded due to aBit
turned off.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.14.1.30 |
mscFrNniDlciDiscCongestedFromIfBytesThis attribute counts the number of byte discards at the Frame
Relay service due to local congestion in the direction toward the
network. When this count reaches maximum, it wraps to zero.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.14.1.31 |
mscFrNniDlciDiscDeCongestedFromIfBytesThis attribute counts the number of discard eligible (DE=1) byte
discards at the Frame Relay service due to local congestion in the
direction toward the network. When the maximum count is reached
the count wraps to zero.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.14.1.32 |
mscFrNniDlciErrorShortBytesFromIfThis attribute counts the bytes received with 0 octets in the
information field. When the count reaches maximum it wraps to
zero.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.14.1.33 |
mscFrNniDlciErrorLongBytesFromIfThis attribute counts the bytes received with number of octets in the
information field greater than the subscribed maximum. When the
count reaches maximum it wraps to zero. Bytes whose lengths are
greater than the hardware receive buffer are ignored by the
hardware and are therefore not included in this count.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.14.1.34 |
mscFrNniDlciRateAdaptReductThis attribute counts the number of rate reductions due to rate
adaptation. Rate adaptation causes the allowed rate to be reduced in
steps. After each reduction, a period of time is awaited before
further action is taken. At the end of this period, the allowed rate is
further reduced if congestion is still prevalent. When this count
reaches maximum, it wraps to zero.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.14.1.35 |
mscFrNniDlciRateAdaptReductPeriodThis attribute provides a cumulative count of the amount of time
that rate adaptation procedures have been in effect. When this count
reaches maximum, it wraps to zero.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.14.1.36 |
mscFrNniDlciTransferPriorityToNetworkThis attribute is obsolete. It is replaced by attribute
transferPriorityToNetwork under group
FrsNniDataLinkConnectionIdentifierServiceParametersOp.roobsolete INTEGER .1.3.6.1.4.1.562.36.2.1.70.5.14.1.37 |
mscFrNniDlciTransferPriorityFromNetworkThis attribute is obsolete. It is replaced by attribute
transferPriorityFromNetwork under group
FrsNniDataLinkConnectionIdentifierServiceParametersOp.roobsolete INTEGER .1.3.6.1.4.1.562.36.2.1.70.5.14.1.38 |
mscFrNniDlciCirPresentThis attribute provides the actual Committed Information Rate
(CIR) enforced for this DLCI. This number is in units of 800 bits/
sec, since that is the internal resolution of Passport rate
enforcement. If rateEnforcement is off, then this number does not
have meaning. Normally, this attribute matches the provisioned CIR
for the DLCI. But when Rate Adaptation is active, then this number
will vary to represent the actual Allowed CIR at the moment that
this attribute is collected.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.14.1.39 |
mscFrNniDlciEirPresentThis attribute provides the actual Excess Information Rate (EIR)
enforced for this DLCI. This number is in units of 800 bits/sec,
since that is the internal resolution of Passport rate enforcement. If
rateEnforcement is off, then this number does not have meaning.
Normally, this attribute matches the provisioned EIR for the DLCI.
But when Rate Adaptation is active, then this number will vary to
represent the actual Allowed EIR at the moment that this attribute is
collected.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.14.1.40 |
mscFrNniDlciIntTableThis group contains the operational statistics for the Frame Relay
Data Link Connection Identifier interval data (accounting data). SEQUENCE OF MscFrNniDlciIntEntry .1.3.6.1.4.1.562.36.2.1.70.5.15 |
mscFrNniDlciIntEntryAn entry in the mscFrNniDlciIntTable. MscFrNniDlciIntEntry .1.3.6.1.4.1.562.36.2.1.70.5.15.1 |
mscFrNniDlciStartTimeThis attribute indicates the start time of this interval period. If Vc
spans 12 hour time or time of day change startTime reflects new
time as recorded at 12 hour periods or time of day changes. A new
interval period is started each time an accounting record is
generated.ro EnterpriseDateAndTime .1.3.6.1.4.1.562.36.2.1.70.5.15.1.1 |
mscFrNniDlciTotalIngressBytesThis attribute counts the total bytes received from the interface
since the start of the interval period. The start of the interval period
is captured in the startTime attribute. The count is reset to zero
when an accounting record is generated.ro Unsigned64 .1.3.6.1.4.1.562.36.2.1.70.5.15.1.2 |
mscFrNniDlciTotalEgressBytesThis attribute counts the total bytes sent to the interface since the
start of the interval period. The start of the interval period is
captured in the startTime attribute. The count is reset to zero when
an accounting record is generated.ro Unsigned64 .1.3.6.1.4.1.562.36.2.1.70.5.15.1.3 |
mscFrNniDlciEirIngressBytesThis attribute counts the total bytes with the Discard Eligibility
(DE) bit set sent to the subnet since the start of the interval period.
The start of the interval period is captured in the startTime attribute.
The count is reset to zero when an accounting record is generated.ro Unsigned64 .1.3.6.1.4.1.562.36.2.1.70.5.15.1.4 |
mscFrNniDlciEirEgressBytesThis attribute counts the total bytes with the Discard Eligibility
(DE) bit set sent to the interface since the start of the interval
period. The start of the interval period is captured in the startTime
attribute. The count is reset to zero when an accounting record is
generated.ro Unsigned64 .1.3.6.1.4.1.562.36.2.1.70.5.15.1.5 |
mscFrNniDlciDiscardedBytesThis attribute counts the total bytes in invalid frames received from
the interface and discarded at the DLCI since the start of the interval
period. This count is a sum of octets in frames discarded due to the
number of octets in the information field greater than the subscribed
maximum or equal to 0, due to aBit turned off, or due to rate
enforcement. The start of the interval period is captured in the
startTime attribute. The count is reset to zero when an accounting
record is generated.ro Unsigned64 .1.3.6.1.4.1.562.36.2.1.70.5.15.1.6 |
mscFrNniDlciTotalIngressSegFrmIf the value of the unitsCounted attribute in moduleData component
is segments, this attribute counts the total number of segments in
frames received from the interface since the start of the interval
period. If the value of the unitsCounted attribute in moduleData
component is frames, this attribute counts the total number of
frames received from the interface since the start of the interval
period. The start of the interval period is captured in the startTime
attribute. The count is reset to zero when an accounting record is
generated.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.15.1.7 |
mscFrNniDlciTotalEgressSegFrmIf the value of the unitsCounted attribute in moduleData component
is segments, this attribute counts the total number of segments in
frames sent to the interface since the start of the interval period. If
the value of the unitsCounted attribute in moduleData component is
frames, this attribute counts the total number of frames sent to the
interface since the start of the interval period. The start of the
interval period is captured in the startTime attribute. The count is
reset to zero when an accounting record is generated.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.15.1.8 |
mscFrNniDlciEirIngressSegFrmIf the value of the unitsCounted attribute in moduleData component
is segments, this attribute counts the number of segments in frames
with the Discard Eligibility (DE) bit set sent to the subnet since the
start of the interval period. If the value of the unitsCounted attribute
in moduleData component is frames, this attribute counts the
number of frames with the Discard Eligibility (DE) bit set sent to
the subnet since the start of the interval period. The start of the
interval period is captured in the startTime attribute. The count is
reset to zero when an accounting record is generated.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.15.1.9 |
mscFrNniDlciEirEgressSegFrmIf the value of the unitsCounted attribute in moduleData component
is segments, this attribute counts the number of segments in frames
with the Discard Eligibility (DE) bit set sent to the interface since
the start of the interval period. If the value of the unitsCounted
attribute in moduleData component is frames, this attribute counts
the number of frames with the Discard Eligibility (DE) bit set sent
to the interface since the start of the interval period. The start of the
interval period is captured in the startTime attribute. The count is
reset to zero when an accounting record is generatedro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.15.1.10 |
mscFrNniDlciDiscardedSegFrmIf the value of the unitsCounted attribute in moduleData component
is segments, this attribute counts the number of segments in invalid
frames received from the interface and discarded at the DLCI. If the
value of the unitsCounted attribute in moduleData component is
frames, this attribute counts the number of invalid frames received
from the interface and discarded at the DLCI. Segments of frames
are counted since the start of the interval period. The count is reset
to zero when an accounting record is generated. The count is a sum
of segments in frames or frames discarded due to the number of
octets in the information field greater than the subscribed maximum
or equal to 0, due to aBit turned off, or due to rate enforcement.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.15.1.11 |
mscFrNniDlciCirPresentObsThis attribute has moved to the statistics subgroup. See cirPresent..roobsolete Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.15.1.12 |
mscFrNniDlciEirPresentObsThis attribute has moved to the statistics group. See eirPresent.roobsolete Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.15.1.13 |
mscFrNniDlciRateEnforcementPresentThis attribute is obsolete. See the provisionable rateEnforcement
attribute.roobsolete Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.15.1.14 |
mscFrNniDlciRateAdaptationPresentThis attribute is obsolete. See the provisionable rateAdaptation
attribute.roobsolete Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.15.1.15 |
mscFrNniDlciLocalRateAdaptOccurredThis attribute indicates whether rate adaptation has occurred on this
user Data Link Connection on this Frame Relay interface. The value
is set to no when an accounting record is generated.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.15.1.16 |
mscFrNniDlciCallReferenceNumberThis attribute is obsoleted and replaced by callRefNumber.roobsolete Hex .1.3.6.1.4.1.562.36.2.1.70.5.15.1.17 |
mscFrNniDlciElapsedDifferenceThis attribute indicates the elapsed time representing the period of
this interval data. It is elapsed time in 0.1 second increments since
the call started.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.15.1.18 |
mscFrNniDlciCallRefNumberThis attribute indicates the call reference number which is a unique
number generated by the switch. The same Call Reference Number
is stored in the interval data (accounting record) at both ends of the
call. It can be used as one of the attributes in matching duplicate
records generated at each end of the connection.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.15.1.20 |
mscFrNniDlciCalldTableThis group of attributes describes the characteristics of the call such
as call type and call state. SEQUENCE OF MscFrNniDlciCalldEntry .1.3.6.1.4.1.562.36.2.1.70.5.16 |
mscFrNniDlciCalldEntryAn entry in the mscFrNniDlciCalldTable. MscFrNniDlciCalldEntry .1.3.6.1.4.1.562.36.2.1.70.5.16.1 |
mscFrNniDlciCallTypeThis attribute indicates whether this DLCI is a permancent virtual
circuit (PVC), a switched virtual circuit (SVC), or a switched
permament virtual circuit (SPVC).ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.16.1.1 |
mscFrNniDlciCallStateThis attribute indicates the FRF.10 state of a switched call. The
value of this attribute for a permanent (PVC and P-SPVC) DLCI is
always notApplicable. In the description that follows, 'calling STE'
refers to the network who has initiated the SETUP request, and
'called STE' refers to the network that receives the request.
State description:
In the null state, the network has neither received nor sent call setup
requests for this DLCI.
In the callInitiated state, the called STE has received a SETUP
message from the calling STE.
In the callProceedingSent state, the called STE has sent a CALL
PROCEEDING message to the calling STE in response to the
SETUP message.
In the callPresent state, the calling STE has sent a SETUP message
to the called STE but has not received a response.
In the callProceedingReceived state, the calling STE has received a
CALL PROCEEDING message from the called STE in response to
a SETUP message.
In the active state, either the called STE has sent a CONNECT
message to the calling STE, or the calling STE has received a
CONNECT from the called STE.
In the releaseRequest state, the STE has sent a RELEASE message
to release the call and is waiting for a RELEASE COMPLETE
message.
In the releaseIndication state, the STE has received a RELEASE
and sends a RELEASE COMPLETE message after releasing the
relevant call resources.
In the restartRequest state, the STE has sent a RESTART request to
the other STE and is waiting for an acknowledgement.
In the restart state, the STE has received a request for a restart from
the other STE and this STE has not returned an acknowledgement.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.5.16.1.2 |
mscFrNniDlciCallReferenceThis attribute indicates the FRF.10 call reference number associated
with this DLCI. The value of this attribute for a provisioned (PVC
or P-SPVC) DLCI is always 0.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.5.16.1.3 |
mscFrNniVFramer OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.1.70.6 |
mscFrNniVFramerRowStatusTableThis entry controls the addition and deletion of
mscFrNniVFramer components. SEQUENCE OF MscFrNniVFramerRowStatusEntry .1.3.6.1.4.1.562.36.2.1.70.6.1 |
mscFrNniVFramerRowStatusEntryA single entry in the table represents a single
mscFrNniVFramer component. MscFrNniVFramerRowStatusEntry .1.3.6.1.4.1.562.36.2.1.70.6.1.1 |
mscFrNniVFramerRowStatusThis variable is used as the basis for SNMP naming of
mscFrNniVFramer components.
These components can be added and deleted.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.6.1.1.1 |
mscFrNniVFramerComponentNameThis variable provides the component's string name for
use with the ASCII Console Interfacero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.6.1.1.2 |
mscFrNniVFramerStorageTypeThis variable represents the storage type value for the
mscFrNniVFramer tables.ro StorageType (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.6.1.1.4 |
mscFrNniVFramerIndexThis variable represents the index for the mscFrNniVFramer tables. NonReplicated .1.3.6.1.4.1.562.36.2.1.70.6.1.1.10 |
mscFrNniVFramerProvTableThis group contains provisionable attributes for the VirtualFramer
component. SEQUENCE OF MscFrNniVFramerProvEntry .1.3.6.1.4.1.562.36.2.1.70.6.10 |
mscFrNniVFramerProvEntryAn entry in the mscFrNniVFramerProvTable. MscFrNniVFramerProvEntry .1.3.6.1.4.1.562.36.2.1.70.6.10.1 |
mscFrNniVFramerOtherVirtualFramerThis attribute specifies the other VirtualFramer to which the service
is linked, for example, FrUni/n VirtualFramer, FrDte/n
VirtualFramer.rw Link .1.3.6.1.4.1.562.36.2.1.70.6.10.1.1 |
mscFrNniVFramerLogicalProcessorThis attribute specifies the logical processor on which the service
component will reside.rw Link .1.3.6.1.4.1.562.36.2.1.70.6.10.1.2 |
mscFrNniVFramerStateTableThis group contains the three OSI State attributes. The descriptions
generically indicate what each state attribute implies about the
component. Note that not all the values and state combinations
described here are supported by every component which uses this
group. For component-specific information and the valid state
combinations, refer to NTP 241-7001-150, Passport Operations and
Maintenance Guide. SEQUENCE OF MscFrNniVFramerStateEntry .1.3.6.1.4.1.562.36.2.1.70.6.11 |
mscFrNniVFramerStateEntryAn entry in the mscFrNniVFramerStateTable. MscFrNniVFramerStateEntry .1.3.6.1.4.1.562.36.2.1.70.6.11.1 |
mscFrNniVFramerAdminStateThis attribute indicates the OSI Administrative State of the
component.
The value locked indicates that the component is administratively
prohibited from providing services for its users. A Lock or Lock -
force command has been previously issued for this component.
When the value is locked, the value of usageState must be idle.
The value shuttingDown indicates that the component is
administratively permitted to provide service to its existing users
only. A Lock command was issued against the component and it is
in the process of shutting down.
The value unlocked indicates that the component is administratively
permitted to provide services for its users. To enter this state, issue
an Unlock command to this component.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.6.11.1.1 |
mscFrNniVFramerOperationalStateThis attribute indicates the OSI Operational State of the component.
The value enabled indicates that the component is available for
operation. Note that if adminState is locked, it would still not be
providing service.
The value disabled indicates that the component is not available for
operation. For example, something is wrong with the component
itself, or with another component on which this one depends. If the
value is disabled, the usageState must be idle.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.6.11.1.2 |
mscFrNniVFramerUsageStateThis attribute indicates the OSI Usage State of the component.
The value idle indicates that the component is not currently in use.
The value active indicates that the component is in use and has
spare capacity to provide for additional users.
The value busy indicates that the component is in use and has no
spare operating capacity for additional users at this time.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.6.11.1.3 |
mscFrNniVFramerStatsTableThis group contains the operational statistics data for a
VirtualFramer component. SEQUENCE OF MscFrNniVFramerStatsEntry .1.3.6.1.4.1.562.36.2.1.70.6.12 |
mscFrNniVFramerStatsEntryAn entry in the mscFrNniVFramerStatsTable. MscFrNniVFramerStatsEntry .1.3.6.1.4.1.562.36.2.1.70.6.12.1 |
mscFrNniVFramerFrmToOtherVFramerThis attribute counts the frames transmitted to the
otherVirtualFramer.ro PassportCounter64 .1.3.6.1.4.1.562.36.2.1.70.6.12.1.2 |
mscFrNniVFramerFrmFromOtherVFramerThis attribute counts the frames received from the
otherVirtualFramer.ro PassportCounter64 .1.3.6.1.4.1.562.36.2.1.70.6.12.1.3 |
mscFrNniVFramerOctetFromOtherVFramerThis attribute counts the octets received from the
otherVirtualFramer.ro PassportCounter64 .1.3.6.1.4.1.562.36.2.1.70.6.12.1.5 |
mscFrNniSig OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.1.70.8 |
mscFrNniSigRowStatusTableThis entry controls the addition and deletion of
mscFrNniSig components. SEQUENCE OF MscFrNniSigRowStatusEntry .1.3.6.1.4.1.562.36.2.1.70.8.1 |
mscFrNniSigRowStatusEntryA single entry in the table represents a single
mscFrNniSig component. MscFrNniSigRowStatusEntry .1.3.6.1.4.1.562.36.2.1.70.8.1.1 |
mscFrNniSigRowStatusThis variable is used as the basis for SNMP naming of
mscFrNniSig components.
These components can be added and deleted.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.8.1.1.1 |
mscFrNniSigComponentNameThis variable provides the component's string name for
use with the ASCII Console Interfacero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.8.1.1.2 |
mscFrNniSigStorageTypeThis variable represents the storage type value for the
mscFrNniSig tables.ro StorageType (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.8.1.1.4 |
mscFrNniSigIndexThis variable represents the index for the mscFrNniSig tables. NonReplicated .1.3.6.1.4.1.562.36.2.1.70.8.1.1.10 |
mscFrNniSigProvTableThis group contains common provisionable attributes for signaling
at the interface. SEQUENCE OF MscFrNniSigProvEntry .1.3.6.1.4.1.562.36.2.1.70.8.11 |
mscFrNniSigProvEntryAn entry in the mscFrNniSigProvTable. MscFrNniSigProvEntry .1.3.6.1.4.1.562.36.2.1.70.8.11.1 |
mscFrNniSigDlciAllocationThis attribute specifies the order in which DLCIs are dynamically
allocated for SVCs. The purpose of this attribute is to prevent DLCI
collisions between SVCs initiated by two FrNni interfaces talking to
each other. This is achieved by provisioning a different value for
this attribute at each end of the NNI link.
A value of fromLowEnd specifies that the DLCI number
assignment for SVC connections is initiated from the lowest value
of the range (that is, highestPvcDlci+1 up to 1007).
A value of fromHighEnd specifies that the DLCI number
assignment for SVC connections is initiated from the highest value
of the range (that is, 1007 down to highestPvcDlci+1).rw Enumeration .1.3.6.1.4.1.562.36.2.1.70.8.11.1.3 |
mscFrNniSigHighestPermanentDlciThis attribute specifies the highest DLCI value that can be
provisioned for a permanent connection. It partitions the DLCI
space into permanent and switched connections. Permanent DLCI
numbers higher than this value cannot be provisioned. The value 0
is used to indicate that no permanent connections are allowed on
this interface. The value 1007 indicates that no switched
connections are allowed on this interface.rwobsolete Unsigned32 (0 | 16..1007) .1.3.6.1.4.1.562.36.2.1.70.8.11.1.4 |
mscFrNniSigHighestPvcDlciThis attribute specifies the highest DLCI value that can be
provisioned for a permanent connection. It partitions the DLCI
space into permanent and switched connections. Permanent DLCI
numbers higher than this value cannot be provisioned. The value 0
is used to indicate that no permanent connections are allowed on
this interface. The value 1007 indicates that no switched
connections are allowed on this interface.rw Unsigned32 (0 | 16..1007) .1.3.6.1.4.1.562.36.2.1.70.8.11.1.5 |
mscFrNniSigServParmsTableThis group contains the provisionable service parameters. SEQUENCE OF MscFrNniSigServParmsEntry .1.3.6.1.4.1.562.36.2.1.70.8.12 |
mscFrNniSigServParmsEntryAn entry in the mscFrNniSigServParmsTable. MscFrNniSigServParmsEntry .1.3.6.1.4.1.562.36.2.1.70.8.12.1 |
mscFrNniSigMaximumFrameSizeThis attribute specifies the maximum number of octets that may be
included in the information field of the user DLCI of any switched
connections using this interface. Its value must not be smaller than
the value of defaultMaximumFrameSize.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.8.12.1.1 |
mscFrNniSigDefaultMaximumFrameSizeThis attribute specifies the default maximum number of octets that
may be included in the information field of the user DLCI assigned
for any switched connections using this interface. This value is used
during call parameter negotiation for switched calls on this interface
when the maximum frame size is not specified in the user's SETUP
message. The value of this attribute must not exceed the value of the
maximumFrameSize attribute.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.8.12.1.2 |
mscFrNniSigDefaultCommittedInformationRateThis attribute specifies the default user to network direction CIR.
This value is used during call parameter negotiation for switched
calls on this interface when the CIR is not specified in the user's
SETUP message.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.8.12.1.3 |
mscFrNniSigDefaultCommittedBurstSizeThis attribute specifies the default user to network direction Bc.
This value is used during call parameter negotiation for switched
calls on this interface when the Bc is not specified in the user's
SETUP message.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.8.12.1.4 |
mscFrNniSigDefaultExcessBurstSizeThis attribute specifies the default user to network direction Be.
This value is used during call parameter negotiation for switched
calls on this interface when the Be is not specified in the user's
SETUP message.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.8.12.1.5 |
mscFrNniSigRateEnforcementThis attribute specifies whether rate enforcement is in effect for
SVCs on this interface.rw Enumeration .1.3.6.1.4.1.562.36.2.1.70.8.12.1.6 |
mscFrNniSigRateAdaptationThis attribute specifies whether closed-loop rate adaptation is in
effect for SVCs on this interface. Rate adaptation is a feature that, in
periods of congestion, adapts the rate at which the user is allowed to
send data into the network to that which the network is able to
handle at that time. This proactive measure of handling congestion
optimizes network resources by causing the ingress to discard
frames that would otherwise be discarded in the network.
If this attribute is set to on, then, at the onset of congestion, the
excess information rate (EIR) is reduced to a very low rate. If
congestion persists, then the allowed CIR is reduced geometrically
by 25% of the current value at that time. The minimum to which
CIR can be reduced is 1/16th (6.25%) of the provisioned value. As
congestion alleviates, CIR is increased linearly by 6.25% of the
provisioned value specified in committedInformationRate.
If set to eirOnly, then rate adaptation will only apply to the excess
information rate (EIR). At the onset of congestion, the allowed EIR
is reduced by 25% of its provisioned value. If congestion persists,
EIR is reduced geometrically by 25% of the current value at that
time. As congestion alleviates, EIR is gradually increased linearly
by 6.25% of the provisioned EIR.
If set to cirProportionate, then rate adaptation will also only apply
to the excess information rate (EIR). At the onset of congestion the
initial allowed EIR is set to a multiple of the provisioned CIR. If
congestion persists, the allowed EIR is reduced geometrically by
25% of the current value at that time. As congestion alleviates, EIR
is gradually increased linearly by 6.25% of the provisioned EIR.
Note that the allowed EIR may be set higher than the provisioned
EIR, since it is calculated initially using another parameter, the
provisioned CIR. If the allowed EIR at the moment is higher than
the provisioned EIR, then the provisioned EIR is used instead.
This attribute can only be set to on or eirOnly if rateEnforcement is
set to on.rw Enumeration .1.3.6.1.4.1.562.36.2.1.70.8.12.1.7 |
mscFrNniSigRaSensitivityThis attribute specifies the sensitivity of the rate adaptation system
for all switched connections on this interface.
A higher number indicates a higher sensitivity and therefore a
quicker reaction time to network conditions. A quicker reaction
time allows the network to discard frames at the access and protect
network resources, but can lead to false alarms and a greater
fluctuation of the allowed rate. A higher setting therefore tends to
favor the protection of the network over the allowed throughput of
the user.
A lower number indicates a lower sensitivity and therefore a slower
reaction to network conditions. A slower reaction time results in a
greater amount of user traffic allowed into the network, but can lead
to a waste of network bandwidth since the traffic may be discarded
at the congested resource. A lower setting therefore tends to favour
the allowed throughput of the user over the protection of the
network.
This attribute is applicable for adapting EIR when rateAdaptation is
eirOnly or cirProportionate, or CIR when rateAdaptation is on.
This attribute is ignored if rateAdaptation is off.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.8.12.1.8 |
mscFrNniSigUpdateBCIThis attribute specifies whether internal Backward Congestion
Indication (BCI) bits will report congestion external to the Passport
network, as communicated through incoming BECN bits.
If updateBCI is set to on, then BCI bits for incoming frames will be
set if the BECN on the frame is set. If updateBCI is set to off, then
incoming BECN bits has no effect.
Setting updateBCI on for a DLCI means that the remote end of the
DLCI, which is specified by the remoteDna and remoteDlci
attributes of the Dc component of the Dlci, may perform Rate
Adaptation using the flow of incoming BECN bits, in addition to
internal Passport congestion management systems.
If the rateAdaptation attribute of the remote DLCI is provisioned as
eirOnly, cirProportionate, or on, then congestion from another
network connected to a Passport network may trigger dynamic
congestion management. If there is no rate adaptation at the other
end, then the setting of updateBCI attribute here will have no effect.rw Enumeration .1.3.6.1.4.1.562.36.2.1.70.8.12.1.9 |
mscFrNniSigSysParmsTableThis group contains the provisionable FRF.10 system parameters. SEQUENCE OF MscFrNniSigSysParmsEntry .1.3.6.1.4.1.562.36.2.1.70.8.13 |
mscFrNniSigSysParmsEntryAn entry in the mscFrNniSigSysParmsTable. MscFrNniSigSysParmsEntry .1.3.6.1.4.1.562.36.2.1.70.8.13.1 |
mscFrNniSigCallSetupTimerThis attribute specifies the time this interface waits for a response to
the SETUP message sent to the adjacent network. Upon timer
expiry, the SETUP message is retransmitted. The second expiry of
this timer causes the call to be cleared.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.8.13.1.1 |
mscFrNniSigReleaseTimerThis attribute specifies the time this interface waits for a response to
the RELEASE message sent to the adjacent network. Upon timer
expiry, the RELEASE message is retransmitted. The second expiry
of the timer causes the call to be released.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.8.13.1.2 |
mscFrNniSigCallProceedingTimerThis attribute specifies the time this interface waits for the
CONNECT message from the adjacent network after the network
has received the optional CALL PROCEEDING message from the
adjacent network. Upon timer expiry, the call is cleared.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.8.13.1.3 |
mscFrNniSigRestartReqTimerThis attribute specifies the time this interface waits for the
RESTART ACKNOWLEDGE message from the adjacent network
after sending a first RESTART message. Upon timer expiry, another
RESTART message is sent. After the second expiry, the interface is
treated as idle.
If the restartReqTimer attribute is set to the default value, then the
interface is treated as idle when it receives an indication that the
link is up and does not send a RESTART message.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.8.13.1.4 |
mscFrNniSigRestartRcvTimerThis attribute specifies the time this interface waits for the
processing of a RESTART message received by the interface. Upon
expiry of this timer, an alarm will be displayed to report the
problem. The timer value must be less than the restartReqTimer
provisioned value at the adjacent node.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.8.13.1.5 |
mscFrNniSigStatusEnqTimerThis attribute specifies the time the network waits for the requested
STATUS message from the adjacent network. Upon expiry of this
timer, another STATUS ENQUIRY message will be sent.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.8.13.1.6 |
mscFrNniSigNetworkTypeThis attribute specifies whether this Frame Relay service is running
on a public or a private network. This value is used solely in
populating applicable information elements within those signaling
messages that require a public or private network indication.rw Enumeration .1.3.6.1.4.1.562.36.2.1.70.8.13.1.7 |
mscFrNniSigLapfSysTableThis group contains the provisionable attributes for the SVC data
link layer. The data link layer is governed primarily through ITU
specification Q.922, and operates over DLCI 0. SEQUENCE OF MscFrNniSigLapfSysEntry .1.3.6.1.4.1.562.36.2.1.70.8.14 |
mscFrNniSigLapfSysEntryAn entry in the mscFrNniSigLapfSysTable. MscFrNniSigLapfSysEntry .1.3.6.1.4.1.562.36.2.1.70.8.14.1 |
mscFrNniSigWindowSizeThis attribute specifies the window size. This is the maximum
number of unacknowledged sequenced frames that may be
outstanding from or to this interface at any one time.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.8.14.1.2 |
mscFrNniSigRetransmitLimitThis attribute specifies the number of times a frame can be
retransmitted by the SVC data link layer before appropriate
recovery action is taken.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.8.14.1.3 |
mscFrNniSigAckTimerThis attribute specifies how long the layer 2 protocol waits for an
acknowledgment to a sent frame. The value set for ackTimer must
be less than the value set for idleProbeTimer.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.8.14.1.4 |
mscFrNniSigAckDelayTimerThis attribute specifies how long the network waits before sending
an acknowledgment for a received in-sequence I-frame. A value of
0 means that every frame is acknowledged and there will be no
delay in acknowledgment. A non-zero value means that one
acknowledgement is sent for a number of frames.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.8.14.1.5 |
mscFrNniSigIdleProbeTimerThis attribute specifies how long the link is permitted to remain idle
(that is, no frames are exchanged on the data link). Upon expiry of
this timer, the network side's link layer polls its peer for status. The
value set for idleProbeTimer must be greater than the value set for
ackTimer.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.8.14.1.6 |
mscFrNniSigCodesTableThis group contains the remote data network address, the last SVC
clear cause and the last SVC diagnostic code coming from the
subnet or the local VC. SEQUENCE OF MscFrNniSigCodesEntry .1.3.6.1.4.1.562.36.2.1.70.8.15 |
mscFrNniSigCodesEntryAn entry in the mscFrNniSigCodesTable. MscFrNniSigCodesEntry .1.3.6.1.4.1.562.36.2.1.70.8.15.1 |
mscFrNniSigLastClearRemoteDataNetworkAddressThis attribute indicates the Data Network Address (DNA) of the
remote (the other end of the SVC connection) of the call which
cleared last and whose clear and diagnostic codes were recorded.ro DigitString .1.3.6.1.4.1.562.36.2.1.70.8.15.1.1 |
mscFrNniSigLastClearCauseThis attribute indicates the last SVC clear cause signalled at the end
of the connection or failure to connect. It is updated only if the clear
request comes from the subnet or the call is rejected locally by the
VC. The same set of possible values provides the clear cause field
in the accounting record.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.8.15.1.2 |
mscFrNniSigLastDiagnosticCodeThis attribute indicates the last SVC diagnostic code signalled at the
end of the connection or failure to connect. It is updated if the clear
request comes from the subnet or the call is rejected locally by the
VC. The same set of possible values provides the diagnostic code
field in the accounting record.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.8.15.1.3 |
mscFrNniSigStateTableThis group contains the three OSI State attributes. The descriptions
generically indicate what each state attribute implies about the
component. Note that not all the values and state combinations
described here are supported by every component which uses this
group. For component-specific information and the valid state
combinations, refer to NTP 241-7001-150, Passport Operations and
Maintenance Guide. SEQUENCE OF MscFrNniSigStateEntry .1.3.6.1.4.1.562.36.2.1.70.8.16 |
mscFrNniSigStateEntryAn entry in the mscFrNniSigStateTable. MscFrNniSigStateEntry .1.3.6.1.4.1.562.36.2.1.70.8.16.1 |
mscFrNniSigAdminStateThis attribute indicates the OSI Administrative State of the
component.
The value locked indicates that the component is administratively
prohibited from providing services for its users. A Lock or Lock -
force command has been previously issued for this component.
When the value is locked, the value of usageState must be idle.
The value shuttingDown indicates that the component is
administratively permitted to provide service to its existing users
only. A Lock command was issued against the component and it is
in the process of shutting down.
The value unlocked indicates that the component is administratively
permitted to provide services for its users. To enter this state, issue
an Unlock command to this component.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.8.16.1.1 |
mscFrNniSigOperationalStateThis attribute indicates the OSI Operational State of the component.
The value enabled indicates that the component is available for
operation. Note that if adminState is locked, it would still not be
providing service.
The value disabled indicates that the component is not available for
operation. For example, something is wrong with the component
itself, or with another component on which this one depends. If the
value is disabled, the usageState must be idle.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.8.16.1.2 |
mscFrNniSigUsageStateThis attribute indicates the OSI Usage State of the component.
The value idle indicates that the component is not currently in use.
The value active indicates that the component is in use and has
spare capacity to provide for additional users.
The value busy indicates that the component is in use and has no
spare operating capacity for additional users at this time.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.8.16.1.3 |
mscFrNniSigStatsTableThis group contains the statistics related to the SVC signaling layer
at the interface level. SEQUENCE OF MscFrNniSigStatsEntry .1.3.6.1.4.1.562.36.2.1.70.8.17 |
mscFrNniSigStatsEntryAn entry in the mscFrNniSigStatsTable. MscFrNniSigStatsEntry .1.3.6.1.4.1.562.36.2.1.70.8.17.1 |
mscFrNniSigCurrentNumberOfSvcCallsThis attribute indicates the number of Frame Relay SVCs currently
existing on this interface.ro Gauge32 .1.3.6.1.4.1.562.36.2.1.70.8.17.1.1 |
mscFrNniSigInCallsThis attribute indicates the current number of incoming SVCs on
this interface (that is, the number of SVCs for which this interface
represents the destination end of the call).ro Gauge32 .1.3.6.1.4.1.562.36.2.1.70.8.17.1.2 |
mscFrNniSigInCallsRefusedThis attribute counts the incoming SVC call requests that are
rejected by either this interface or by the called user. When this
count exceeds the maximum, it wraps to zero.ro Counter32 .1.3.6.1.4.1.562.36.2.1.70.8.17.1.3 |
mscFrNniSigOutCallsThis attribute indicates the current number of outgoing SVCs on
this interface (that is, the number of SVCs for which this interface
represents the source end of the call).ro Gauge32 .1.3.6.1.4.1.562.36.2.1.70.8.17.1.4 |
mscFrNniSigOutCallsFailedThis attribute counts the outgoing SVC call requests that are
rejected by either this interface, or by the network side of the
destination end, or by the called user. When this count exceeds the
maximum, it wraps to zero.ro Counter32 .1.3.6.1.4.1.562.36.2.1.70.8.17.1.5 |
mscFrNniSigProtocolErrorsThis attribute counts the number of times a FRF.10 protocol error
has occurred. Any one of the following events constitutes a protocol
error:
1. In the user-signaled Link Layer Core Parameters IE within the
SETUP or CONNECT messages, Cir, Bc and Be are all zero;
2. In the user-signaled Link Layer Core Parameters IE within the
SETUP or CONNECT messages, Cir is zero but Bc is
non-zero, or Bc is zero but Cir is non-zero;
3. In the user-signaled Link Layer Core Parameters IE within the
SETUP or CONNECT messages, the Minimum Acceptable CIR
is greater than Cir;
4. At the destination end, any of the destination to source direction
link layer core parameters has been increased in the
CONNECT message from the called user;
5. At the destination end, the destination to source direction Cir
in the CONNECT message is smaller than the corresponding
minimum acceptable Cir signaled to the called user;
6. At the source end, any of the source to destination direction
link layer core parameters in the CONNECT message from the
destination end has been increased;
7. At the source end, the source to destination direction Cir, after
negotiation, is smaller than the corresponding minimum
acceptable Cir;
8. The network has received a STATUS message from the user
with an incompatible FRF.10 state.
When this count reaches maximum, it wraps to zero.ro Counter32 .1.3.6.1.4.1.562.36.2.1.70.8.17.1.6 |
mscFrNniSigQualityOfServiceNotAvailableThis attribute counts the number of incoming and outgoing SVCs
that are rejected because the quality of service requested cannot be
met by the network. When this count reaches maximum, it wraps to
zero.ro Counter32 .1.3.6.1.4.1.562.36.2.1.70.8.17.1.7 |
mscFrNniSigSetupTimeoutThis attribute counts the number of times the T303 setup timer has
expired. When this count reaches maximum, it wraps to zero.ro Counter32 .1.3.6.1.4.1.562.36.2.1.70.8.17.1.8 |
mscFrNniSigLastCauseInStatusMsgReceivedThis attribute indicates the cause value in the last received user's
STATUS message to an existing call. The DLCI to which this
STATUS message applies is specified in the lastDlciReceivedStatus
attribute.
The initial value of this attribute is 0 which means that no STATUS
message has been received for an existing call yet.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.8.17.1.9 |
mscFrNniSigLastStateInStatusMsgReceivedThis attribute indicates the state value in the last received user's
STATUS message to an existing call. The DLCI to which this
STATUS message applies is specified in the lastDlciReceivedStatus
attribute.
The initial value of this attribute is notApplicable.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.8.17.1.10 |
mscFrNniSigLastDlciReceivedStatusThis attribute shows the value of the DLCI that has most recently
received a STATUS message from the user.
The initial value of this attribute is 0.ro Unsigned32 (0 | 16..1007) .1.3.6.1.4.1.562.36.2.1.70.8.17.1.11 |
mscFrNniSigLastStateReceivedStatusThis attribute shows the network FRF.10 state of the DLCI that has
most recently received a STATUS message from the user. The DLCI
to which this STATUS message applies is specified in the
lastDlciReceivedStatus attribute.
The initial value of this attribute is notApplicable.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.8.17.1.12 |
mscFrNniSigDlciCollisionsThis attribute counts the number of call failures due to DLCI
collisions.ro Counter32 .1.3.6.1.4.1.562.36.2.1.70.8.17.1.15 |
mscFrNniSigLapfStatusTableThis group contains the Q.922 SVC data link layer status. SEQUENCE OF MscFrNniSigLapfStatusEntry .1.3.6.1.4.1.562.36.2.1.70.8.18 |
mscFrNniSigLapfStatusEntryAn entry in the mscFrNniSigLapfStatusTable. MscFrNniSigLapfStatusEntry .1.3.6.1.4.1.562.36.2.1.70.8.18.1 |
mscFrNniSigCurrentStateThis attribute shows the current state of the SVC data link layer
interface.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.8.18.1.1 |
mscFrNniSigLastStateChangeReasonThis attribute shows the reason for the most recent state change.
notStarted - this is the default state after SVC data link has just
been created.
abmeEntered - SVC data link has entered Asynchronous Balanced
Mode after SABME or UA has been received.
abmeReset - the data link has been reset.
dmReceived - DM response received.
dmSent - DM sent.
discReceived - DISC response received.
discSent - DISC sent.
frmrReceived - FRMR received.
n200RetranTimeOut - retransmitLimit has been exceeded.
other - unspecified state change reasons. The most likely reason for
this is the transition from state waitingAck to state
informationTransfer.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.8.18.1.2 |
mscFrNniSigFrmrReceiveThis attribute shows the information field of the Frame Reject
(FRMR) most recently received.ro HexString .1.3.6.1.4.1.562.36.2.1.70.8.18.1.3 |
mscFrNniSigCurrentQueueSizeThis attribute shows the current number of frames in the SVC data
link layer transmit queue.ro Counter32 .1.3.6.1.4.1.562.36.2.1.70.8.18.1.4 |
mscFrNniSigLapfStatsTableThis group contains the statistics for the SVC data link layer. SEQUENCE OF MscFrNniSigLapfStatsEntry .1.3.6.1.4.1.562.36.2.1.70.8.19 |
mscFrNniSigLapfStatsEntryAn entry in the mscFrNniSigLapfStatsTable. MscFrNniSigLapfStatsEntry .1.3.6.1.4.1.562.36.2.1.70.8.19.1 |
mscFrNniSigRemoteBusyThis attribute counts the number of times transmission of an I-frame
was unsuccessful due to a perceived remote busy condition
(window closed or remote busy). When this count reaches
maximum, it wraps to zero.ro Counter32 .1.3.6.1.4.1.562.36.2.1.70.8.19.1.2 |
mscFrNniSigReceiveRejectFrameThis attribute counts the number of REJ frames received by the
interface. When this count reaches maximum, it wraps to zero.ro Counter32 .1.3.6.1.4.1.562.36.2.1.70.8.19.1.3 |
mscFrNniSigAckTimeoutThis attribute counts the number of times the ackTimer has expired.
Frequent increments of this counter indicate a problem at the link or
improper values have been chosen for ackTimer and ackDelayTimer
between the local and remote sides. When this count reaches
maximum, it wraps to zero.ro Counter32 .1.3.6.1.4.1.562.36.2.1.70.8.19.1.4 |
mscFrNniSigIFramesTransmittedThis attribute counts the number of SVC I-frames transmitted to the
interface on DLCI 0. An I-frame may be counted more than once if
there are retransmissions at the SVC data link layer. When this
count reaches maximum, it wraps to zero.ro Counter32 .1.3.6.1.4.1.562.36.2.1.70.8.19.1.5 |
mscFrNniSigIFramesTxDiscardedThis attribute counts the number of SVC I-frames that are bound for
the link but have been discarded. Discard reasons may be one of the
following:
1. the frame length is beyond the allowed limit.
2. the SVC data link layer is in disconnected state.
3. the transmit queue has been purged because the queue length
has reached the reset threshold.
4. the transmit queue or the queue waiting for acknowledgment
has been purged because the link cannot be re-established.
When this count reaches maximum, it wraps to zero.ro Counter32 .1.3.6.1.4.1.562.36.2.1.70.8.19.1.6 |
mscFrNniSigIFramesReceivedThis attribute counts the number of SVC I-frames received from the
interface. When this count reaches maximum, it wraps to zero.ro Counter32 .1.3.6.1.4.1.562.36.2.1.70.8.19.1.7 |
mscFrNniSigIFramesRcvdDiscardedThis attribute counts the number of SVC I-frames received but have
been discarded. The discard reasons are:
1. incorrect frame size
2. frame is out of sequence
3. frame received while the network side of the SVC data link
layer is not in the informationTransfer or waitingAck state.
When this count reaches maximum, it wraps to zero.ro Counter32 .1.3.6.1.4.1.562.36.2.1.70.8.19.1.8 |
mscFrNniSigStateChangeThis attribute counts the number of times the SVC data link layer
interface has changed state. While the data link layer is in
informationTransfer state, this counter will increment on each
expiry of idleProbeTimer as its state goes from
informationTransfer to waitingAck and back. When this count
exceeds the maximum, it wraps to zero.ro Counter32 .1.3.6.1.4.1.562.36.2.1.70.8.19.1.8650 |
mscFrNniSigSvcaccTableThis group contains the provisionable attribute which controls
accounting for this interface. SEQUENCE OF MscFrNniSigSvcaccEntry .1.3.6.1.4.1.562.36.2.1.70.8.20 |
mscFrNniSigSvcaccEntryAn entry in the mscFrNniSigSvcaccTable. MscFrNniSigSvcaccEntry .1.3.6.1.4.1.562.36.2.1.70.8.20.1 |
mscFrNniSigDefaultAccountingThis attribute specifies whether accounting data collection and
record generation is turned on for switched connections at this
interface. For accounting data collection and record generation to
occur, this attribute must be on and at least one of the
accountCollection reasons in the Dna component must be present.rw Enumeration .1.3.6.1.4.1.562.36.2.1.70.8.20.1.1 |
mscFrNniSigBandwidthNotAvailableTableThis attribute counts the number of call failures for each bandwidth
pool due to the requested bandwidth not being available. SEQUENCE OF MscFrNniSigBandwidthNotAvailableEntry .1.3.6.1.4.1.562.36.2.1.70.8.672 |
mscFrNniSigBandwidthNotAvailableEntryAn entry in the mscFrNniSigBandwidthNotAvailableTable. MscFrNniSigBandwidthNotAvailableEntry .1.3.6.1.4.1.562.36.2.1.70.8.672.1 |
mscFrNniSigBandwidthNotAvailableIndexThis variable represents the mscFrNniSigBandwidthNotAvailableTable
specific index for the mscFrNniSigBandwidthNotAvailableTable. Integer32 .1.3.6.1.4.1.562.36.2.1.70.8.672.1.1 |
mscFrNniSigBandwidthNotAvailableValueThis variable represents an individual value for the
mscFrNniSigBandwidthNotAvailableTable.ro Counter32 .1.3.6.1.4.1.562.36.2.1.70.8.672.1.2 |
mscFrNniLts OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.1.70.9 |
mscFrNniLtsRowStatusTableThis entry controls the addition and deletion of
mscFrNniLts components. SEQUENCE OF MscFrNniLtsRowStatusEntry .1.3.6.1.4.1.562.36.2.1.70.9.1 |
mscFrNniLtsRowStatusEntryA single entry in the table represents a single
mscFrNniLts component. MscFrNniLtsRowStatusEntry .1.3.6.1.4.1.562.36.2.1.70.9.1.1 |
mscFrNniLtsRowStatusThis variable is used as the basis for SNMP naming of
mscFrNniLts components.
These components can be added and deleted.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.9.1.1.1 |
mscFrNniLtsComponentNameThis variable provides the component's string name for
use with the ASCII Console Interfacero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.9.1.1.2 |
mscFrNniLtsStorageTypeThis variable represents the storage type value for the
mscFrNniLts tables.ro StorageType (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.9.1.1.4 |
mscFrNniLtsIndexThis variable represents the index for the mscFrNniLts tables. NonReplicated .1.3.6.1.4.1.562.36.2.1.70.9.1.1.10 |
mscFrNniLtsPat OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.1.70.9.2 |
mscFrNniLtsPatRowStatusTableThis entry controls the addition and deletion of
mscFrNniLtsPat components. SEQUENCE OF MscFrNniLtsPatRowStatusEntry .1.3.6.1.4.1.562.36.2.1.70.9.2.1 |
mscFrNniLtsPatRowStatusEntryA single entry in the table represents a single
mscFrNniLtsPat component. MscFrNniLtsPatRowStatusEntry .1.3.6.1.4.1.562.36.2.1.70.9.2.1.1 |
mscFrNniLtsPatRowStatusThis variable is used as the basis for SNMP naming of
mscFrNniLtsPat components.
These components can be added and deleted.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.9.2.1.1.1 |
mscFrNniLtsPatComponentNameThis variable provides the component's string name for
use with the ASCII Console Interfacero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.9.2.1.1.2 |
mscFrNniLtsPatStorageTypeThis variable represents the storage type value for the
mscFrNniLtsPat tables.ro StorageType (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.9.2.1.1.4 |
mscFrNniLtsPatIndexThis variable represents the index for the mscFrNniLtsPat tables. Integer32 .1.3.6.1.4.1.562.36.2.1.70.9.2.1.1.10 |
mscFrNniLtsPatDefaultsTableThis attribute group contains the specifications of the pattern. SEQUENCE OF MscFrNniLtsPatDefaultsEntry .1.3.6.1.4.1.562.36.2.1.70.9.2.10 |
mscFrNniLtsPatDefaultsEntryAn entry in the mscFrNniLtsPatDefaultsTable. MscFrNniLtsPatDefaultsEntry .1.3.6.1.4.1.562.36.2.1.70.9.2.10.1 |
mscFrNniLtsPatDefaultDlciThis attribute specifies for which dlci (on the local end) the frames
are destined.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.9.2.10.1.200 |
mscFrNniLtsPatDefaultNumFramesThis attribute specifies the number of frames in this pattern. This is
the number of frames of this type which will be generated in one
timeInterval.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.9.2.10.1.201 |
mscFrNniLtsPatDefaultDataSizeThis attribute specifies the payload size of each frame in bytes.
This is in excess to the header.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.9.2.10.1.202 |
mscFrNniLtsPatDefaultHeaderBitsThis attribute specifies whether the following bits are on/off in the
header of each frame. The following bits can be set:
BeCn, C/R, De, FeCn
Description of bits:
becn(0)
fecn(1)
cr(2)
de(3)rw OCTET STRING .1.3.6.1.4.1.562.36.2.1.70.9.2.10.1.203 |
mscFrNniLtsPatDefaultHeaderLengthThis attribute specifies the size of the frame relay header in bytes.
Passport currently only supports a 2-byte header.rw Unsigned32 (0 | 2..4) .1.3.6.1.4.1.562.36.2.1.70.9.2.10.1.204 |
mscFrNniLtsPatDefaultEABitsThis attribute specifies how the address field extension bits are set in
the frame header. Consider the value to be a four bit binary number.
For example, 4 = 0100. Only the first headerLength bits are used.
For instance, suppose headerLength is 3, then the appropriate
EABits is 2, or 0010. This attribute can be used to create a header
of length greater than two bytes or to specify incorrect EABits in
the header.rw Hex .1.3.6.1.4.1.562.36.2.1.70.9.2.10.1.205 |
mscFrNniLtsPatDefaultPayloadPatternThis attribute specifies the payload of each frame. The value
specified is in hexadecimal, where every two digits represent a byte.
A maximum of 24 digits (12 bytes) may be set, after which the
pattern will repeat in the payload (depending on repeatPattern
attribute).
NOTE: If a RFC 1490 header is specified, via the 1490Header
attribute, the specified pattern will begin following the header (i.e.
at the 9th byte in the payload).rw HexString .1.3.6.1.4.1.562.36.2.1.70.9.2.10.1.206 |
mscFrNniLtsPatDefaultRfc1490HeaderThis attribute specifies the appropriate RFC 1490 encapsulated
header of the frame. A value of 0 indicates no 1490 header.
NOTE: This header resides in the first 8 bytes of the payload. If the
specified value is non-zero, then the payload pattern provisioned
will begin at the 9th byte.rw Enumeration .1.3.6.1.4.1.562.36.2.1.70.9.2.10.1.207 |
mscFrNniLtsPatDefaultUseBadLrcThis attribute specifies whether the frames from this pattern are to
have a bad LRC prior to being sent to the framer. The LRC is
checked while the frame is being put onto the link and the failure
should cause an abort frame to be sent.rw Enumeration .1.3.6.1.4.1.562.36.2.1.70.9.2.10.1.208 |
mscFrNniLtsPatSetupTableThis attribute group contains the specifications of the pattern. SEQUENCE OF MscFrNniLtsPatSetupEntry .1.3.6.1.4.1.562.36.2.1.70.9.2.11 |
mscFrNniLtsPatSetupEntryAn entry in the mscFrNniLtsPatSetupTable. MscFrNniLtsPatSetupEntry .1.3.6.1.4.1.562.36.2.1.70.9.2.11.1 |
mscFrNniLtsPatDlciThis attribute specifies for which dlci (on the local end) the frames
are destined.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.9.2.11.1.200 |
mscFrNniLtsPatNumFramesThis attribute specifies the number of frames in this pattern. This is
the number of frames of this type which will be generated in one
timeInterval.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.9.2.11.1.201 |
mscFrNniLtsPatDataSizeThis attribute specifies the payload size of each frame in bytes.
This is in excess to the header.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.9.2.11.1.202 |
mscFrNniLtsPatHeaderBitsThis attribute specifies whether the following bits are on/off in the
header of each frame. The following bits can be set:
BeCn, C/R, De, FeCn
Description of bits:
becn(0)
fecn(1)
cr(2)
de(3)rw OCTET STRING .1.3.6.1.4.1.562.36.2.1.70.9.2.11.1.203 |
mscFrNniLtsPatHeaderLengthThis attribute specifies the size of the frame relay header in bytes.
Passport currently only supports a 2-byte header. Valid values are
0, 2, 3, 4. 0 indicates to use no header. That is, the frame will start
with either the payload or rfc1490 header.rw Unsigned32 (0 | 2..4) .1.3.6.1.4.1.562.36.2.1.70.9.2.11.1.204 |
mscFrNniLtsPatEaBitsThis attribute specifies how the address field extension bits are set in
the frame header. Consider the value to be a four bit binary number.
For example, 4 = 0100. Only the first headerLength bits are used.
For instance, suppose headerLength is 3, then the appropriate eaBits
is 2, or 0010. This attribute can be used to create a header of length
greater than two bytes or to specify incorrect eaBits in the header.rw Hex .1.3.6.1.4.1.562.36.2.1.70.9.2.11.1.205 |
mscFrNniLtsPatPayloadPatternThis attribute specifies the payload of each frame. The value
specified is in hexadecimal, where every two digits represent a byte.
A maximum of 24 digits (12 bytes) may be set, after which the
pattern will repeat in the payload (depending on repeatPattern
attribute).
NOTE: If a RFC 1490 header is specified, via the 1490Header
attribute, the specified pattern will begin following the header (i.e.
at the 9th byte in the payload).rw HexString .1.3.6.1.4.1.562.36.2.1.70.9.2.11.1.206 |
mscFrNniLtsPatRfc1490HeaderThis attribute specifies the appropriate RFC 1490 encapsulated
header of the frame. A value of 0 indicates no 1490 header.
NOTE: This header resides in the first 8 bytes of the payload. If the
specified value is non-zero, then the payload pattern provisioned
will begin at the 9th byte.rw Enumeration .1.3.6.1.4.1.562.36.2.1.70.9.2.11.1.207 |
mscFrNniLtsPatUseBadLrcThis attribute specifies whether the frames from this pattern are to
have a bad LRC prior to being sent to the framer. The LRC is
checked while the frame is being put onto the link and the failure
should cause an abort frame to be sent.rw Enumeration .1.3.6.1.4.1.562.36.2.1.70.9.2.11.1.208 |
mscFrNniLtsPatOpDataTableThis group contains the operational attributes which allow changing
the pattern outside of provisioning mode. SEQUENCE OF MscFrNniLtsPatOpDataEntry .1.3.6.1.4.1.562.36.2.1.70.9.2.12 |
mscFrNniLtsPatOpDataEntryAn entry in the mscFrNniLtsPatOpDataTable. MscFrNniLtsPatOpDataEntry .1.3.6.1.4.1.562.36.2.1.70.9.2.12.1 |
mscFrNniLtsPatFramePatternThis attribute displays the first 20 to 24 bytes of the frame payload,
depending on the frame relay header size selected. This attribute
represents the frame if it were at least 20 to 24 bytes in size. That
is, the actual frame may be smaller.ro HexString .1.3.6.1.4.1.562.36.2.1.70.9.2.12.1.200 |
mscFrNniLtsPatHdlcBitsInsertedThis attribute displays how many times a zero bit will be inserted
after 5 consecutive 1 bits when a frame from this pattern is sent out.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.9.2.12.1.201 |
mscFrNniLtsPatOpStateTableThis group contains the attributes containing the operational
statistics of the pattern. SEQUENCE OF MscFrNniLtsPatOpStateEntry .1.3.6.1.4.1.562.36.2.1.70.9.2.13 |
mscFrNniLtsPatOpStateEntryAn entry in the mscFrNniLtsPatOpStateTable. MscFrNniLtsPatOpStateEntry .1.3.6.1.4.1.562.36.2.1.70.9.2.13.1 |
mscFrNniLtsPatLoadThis attribute indicates the load due to this particular pattern. The
loads associated with all of the provisioned patterns are summed to
arrive at the FrLts load.ro FixedPoint3 .1.3.6.1.4.1.562.36.2.1.70.9.2.13.1.200 |
mscFrNniLtsPatStatusThis attributes specifies the administrative state of the pattern. A
disabled pattern will not be generated, although it can still be
triggered.rw Enumeration .1.3.6.1.4.1.562.36.2.1.70.9.2.13.1.201 |
mscFrNniLtsSetupTableThis attribute group contains the parameters used to configure the
behavior of the Frame Relay Load Test System. SEQUENCE OF MscFrNniLtsSetupEntry .1.3.6.1.4.1.562.36.2.1.70.9.10 |
mscFrNniLtsSetupEntryAn entry in the mscFrNniLtsSetupTable. MscFrNniLtsSetupEntry .1.3.6.1.4.1.562.36.2.1.70.9.10.1 |
mscFrNniLtsDurationThis attribute specifies the duration of the test in milliseconds. The
test will run until the duration expires or the STOP command is
issued. A value of 0 is used to indicate infinity.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.9.10.1.200 |
mscFrNniLtsAlgorithmThis attribute specifies which algorithm is used to generate the
frames.
ContinuousBurst
This mode of traffic generation creates traffic at the maximum rate
possible until all of the frames have been sent. The generator then
waits until the end of the timeInterval to begin again.
IntervalBurst
This algorithm attempts to generate 10 ms bursts of burstSize
frames. It will generate as many of the burstSize frames as it can per
sub-interval.
DelayedBurst
This algorithm generates bursts of burstSize frames separated by 10
ms delays.
FixedBurst
This aglorithm is similar to IntervalBurst, except a fixed burst size
of 12 frames is used.
delayMeasurement
This algorithm is used to measure delay. The specified number of
frames in the indicated pattern are generated, one at a time, with a
maximum wait of maxDelay before sending the next frame.
This algorithm is not implemented yet.rw Enumeration .1.3.6.1.4.1.562.36.2.1.70.9.10.1.201 |
mscFrNniLtsBurstSizeThis attribute specifies the number of frames per burst under the
delayedBurst and intervalBurst algorithms.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.9.10.1.204 |
mscFrNniLtsTimeIntervalThis attribute specifies the time interval to the specified number of
seconds. Granuality is in centiseconds. Maximum is 1 minute.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.9.10.1.205 |
mscFrNniLtsStateTableThis group contains the operation statistics of the load generator. SEQUENCE OF MscFrNniLtsStateEntry .1.3.6.1.4.1.562.36.2.1.70.9.11 |
mscFrNniLtsStateEntryAn entry in the mscFrNniLtsStateTable. MscFrNniLtsStateEntry .1.3.6.1.4.1.562.36.2.1.70.9.11.1 |
mscFrNniLtsGeneratorStateThis attribute indicates whether the Lts is generating traffic.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.9.11.1.200 |
mscFrNniLtsCycleIncompleteThis attribute indicates whether the time required to generate all of
the enabled patterns is more than timeInterval by a true value.
Otherwise, this flag is set to false. Default is True.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.9.11.1.201 |
mscFrNniLtsLastActiveIntervalThis attribute indicates the actual time it took to generate all of the
enabled patterns in the last cycle. If cycleIncomplete is true, this
value should be zero.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.9.11.1.202 |
mscFrNniLtsLoadThis attribute indicates the load being generated. This value
represents that calculated using the set number of ticks. The actual
burstTimeInterval may differ. One entire cycle of the patterns is
completed in activeInterval and thus most of the load may be
concentrated early in the set interval.ro FixedPoint3 .1.3.6.1.4.1.562.36.2.1.70.9.11.1.204 |
mscFrNniLtsElapsedGenerationTimeThis attribute indicates how many milliseconds have elapsed since
the start of this test.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.9.11.1.205 |
mscFrNniLtsResultsTableThis group contains the frame counting attributes for the LTS
component. SEQUENCE OF MscFrNniLtsResultsEntry .1.3.6.1.4.1.562.36.2.1.70.9.12 |
mscFrNniLtsResultsEntryAn entry in the mscFrNniLtsResultsTable. MscFrNniLtsResultsEntry .1.3.6.1.4.1.562.36.2.1.70.9.12.1 |
mscFrNniLtsFramesTxThis attribute specifies the number of frames send to the network
since the last time these statistics were cleared. This is similar to the
framesToIf attribute of the FRAMER component.ro Counter32 .1.3.6.1.4.1.562.36.2.1.70.9.12.1.200 |
mscFrNniLtsBytesTxThis attribute indicates the number of bytes sent.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.9.12.1.204 |
mscFrNniLtsBitRateTxThis attribute indicates the bit rate being sent to the link. It should
only differ from the load if the burstTimeInterval would be >= the
timeInterval or burstSize frames cannot be generated in 10ms
(intervalBurst algorithm).ro FixedPoint3 .1.3.6.1.4.1.562.36.2.1.70.9.12.1.208 |
mscFrNniLtsFrameRateTxThis attribute indicates the frame rate being sent to the link. It is
calculated using the number of frames sent to the link in one cycle
of the patterns.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.9.12.1.209 |
mscFrNniCidDataTableThis group contains the attribute for a component's Customer
Identifier (CID). Refer to the attribute description for a detailed
explanation of CIDs. SEQUENCE OF MscFrNniCidDataEntry .1.3.6.1.4.1.562.36.2.1.70.10 |
mscFrNniCidDataEntryAn entry in the mscFrNniCidDataTable. MscFrNniCidDataEntry .1.3.6.1.4.1.562.36.2.1.70.10.1 |
mscFrNniCustomerIdentifierThis attribute holds the Customer Identifier (CID).
Every component has a CID. If a component has a cid attribute, the
component's CID is the provisioned value of that attribute;
otherwise the component inherits the CID of its parent. The top-
level component has a CID of 0.
Every operator session also has a CID, which is the CID
provisioned for the operator's user ID. An operator will see only the
stream data for components having a matching CID. Also, the
operator will be allowed to issue commands for only those
components which have a matching CID.
An operator CID of 0 is used to identify the Network Manager
(referred to as 'NetMan' in DPN). This CID matches the CID of
any component. Values 1 to 8191 inclusive (equivalent to 'basic
CIDs' in DPN) may be assigned to specific customers.rw Unsigned32 (0 | 1..8191) .1.3.6.1.4.1.562.36.2.1.70.10.1.1 |
mscFrNniStateTableThis group contains the three OSI State attributes and the six OSI
Status attributes. The descriptions generically indicate what each
attribute implies about the component. Note that not all the values
and state combinations described here are supported by every
component which uses this group. For component-specific
information and the valid state combinations, refer to NTP 241-
7001-150, Passport Operations and Maintenance Guide. SEQUENCE OF MscFrNniStateEntry .1.3.6.1.4.1.562.36.2.1.70.11 |
mscFrNniStateEntryAn entry in the mscFrNniStateTable. MscFrNniStateEntry .1.3.6.1.4.1.562.36.2.1.70.11.1 |
mscFrNniAdminStateThis attribute indicates the OSI Administrative State of the
component.
The value locked indicates that the component is administratively
prohibited from providing services for its users. A Lock or Lock -
force command has been previously issued for this component.
When the value is locked, the value of usageState must be idle.
The value shuttingDown indicates that the component is
administratively permitted to provide service to its existing users
only. A Lock command was issued against the component and it is
in the process of shutting down.
The value unlocked indicates that the component is administratively
permitted to provide services for its users. To enter this state, issue
an Unlock command to this component.
The OSI Status attributes, if supported by the component, may
provide more details, qualifying the state of the component.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.11.1.1 |
mscFrNniOperationalStateThis attribute indicates the OSI Operational State of the component.
The value enabled indicates that the component is available for
operation. Note that if adminState is locked, it would still not be
providing service.
The value disabled indicates that the component is not available for
operation. For example, something is wrong with the component
itself, or with another component on which this one depends. If the
value is disabled, the usageState must be idle.
The OSI Status attributes, if supported by the component, may
provide more details, qualifying the state of the component.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.11.1.2 |
mscFrNniUsageStateThis attribute indicates the OSI Usage State of the component.
The value idle indicates that the component is not currently in use.
The value active indicates that the component is in use and has
spare capacity to provide for additional users.
The value busy indicates that the component is in use and has no
spare operating capacity for additional users at this time.
The OSI Status attributes, if supported by the component, may
provide more details, qualifying the state of the component.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.11.1.3 |
mscFrNniAvailabilityStatusIf supported by the component, this attribute indicates the OSI
Availability status of the component. Note that, even though it is
defined as a multi-valued set, at most one value is shown to the user.
When no values are in the set, this indicates that either the attribute
is not supported or that none of the status conditions described
below are present.
The value inTest indicates that the resource is undergoing a test
procedure. If adminState is locked or shuttingDown, the normal
users are precluded from using the resource and controlStatus is
reservedForTest. Tests that do not exclude additional users can be
present in any operational or administrative state but the
reservedForTest condition should not be present.
The value failed indicates that the component has an internal fault
that prevents it from operating. The operationalState is disabled.
The value dependency indicates that the component cannot operate
because some other resource on which it depends is unavailable.
The operationalState is disabled.
The value powerOff indicates the resource requires power to be
applied and it is not powered on. The operationalState is disabled.
The value offLine indicates the resource requires a routine
operation (either manual, automatic, or both) to be performed to
place it on-line and make it available for use. The operationalState
is disabled.
The value offDuty indicates the resource is inactive in accordance
with a predetermined time schedule. In the absence of other
disabling conditions, the operationalState is enabled or disabled.
The value degraded indicates the service provided by the
component is degraded in some way, such as in speed or operating
capacity. However, the resource remains available for service. The
operationalState is enabled.
The value notInstalled indicates the resource is not present. The
operationalState is disabled.
The value logFull is not used.
Description of bits:
inTest(0)
failed(1)
powerOff(2)
offLine(3)
offDuty(4)
dependency(5)
degraded(6)
notInstalled(7)
logFull(8)ro OCTET STRING .1.3.6.1.4.1.562.36.2.1.70.11.1.4 |
mscFrNniProceduralStatusIf supported by the component, this attribute indicates the OSI
Procedural status of the component. Note that, even though it is
defined as a multi-valued set, at most one value is shown to the user.
When no values are in the set, this indicates that either the attribute
is not supported or that none of the status conditions described
below are present.
The value initializationRequired indicates (for a resource which
doesn't initialize autonomously) that initialization is required before
it can perform its normal functions, and this procedure has not been
initiated. The operationalState is disabled.
The value notInitialized indicates (for a resource which does
initialize autonomously) that initialization is required before it can
perform its normal functions, and this procedure has not been
initiated. The operationalState may be enabled or disabled.
The value initializing indicates that initialization has been initiated
but is not yet complete. The operationalState may be enabled or
disabled.
The value reporting indicates the resource has completed some
processing operation and is notifying the results. The
operationalState is enabled.
The value terminating indicates the component is in a termination
phase. If the resource doesn't reinitialize autonomously,
operationalState is disabled; otherwise it is enabled or disabled.
Description of bits:
initializationRequired(0)
notInitialized(1)
initializing(2)
reporting(3)
terminating(4)ro OCTET STRING .1.3.6.1.4.1.562.36.2.1.70.11.1.5 |
mscFrNniControlStatusIf supported by the component, this attribute indicates the OSI
Control status of the component. Note that, even though it is defined
as a multi-valued set, at most one value is shown to the user.
When no values are in the set, this indicates that either the attribute
is not supported or that none of the status conditions described
below are present.
The value subjectToTest indicates the resource is available but tests
may be conducted simultaneously at unpredictable times, which
may cause it to exhibit unusual characteristics.
The value partOfServicesLocked indicates that part of the service is
restricted from users of a resource. The adminState is unlocked.
The value reservedForTest indicates that the component is
administratively unavailable because it is undergoing a test
procedure. The adminState is locked.
The value suspended indicates that the service has been
administratively suspended.
Description of bits:
subjectToTest(0)
partOfServicesLocked(1)
reservedForTest(2)
suspended(3)ro OCTET STRING .1.3.6.1.4.1.562.36.2.1.70.11.1.6 |
mscFrNniAlarmStatusIf supported by the component, this attribute indicates the OSI
Alarm status of the component. Note that, even though it is defined
as a multi-valued set, at most one value is shown to the user.
When no values are in the set, this indicates that either the attribute
is not supported or that none of the status conditions described
below are present.
The value underRepair indicates the component is currently being
repaired. The operationalState is enabled or disabled.
The value critical indicates one or more critical alarms are
outstanding against the component. Other, less severe, alarms may
also be outstanding. The operationalState is enabled or disabled.
The value major indicates one or more major alarms are
outstanding against the component. Other, less severe, alarms may
also be outstanding. The operationalState is enabled or disabled.
The value minor indicates one or more minor alarms are
outstanding against the component. Other, less severe, alarms may
also be outstanding. The operationalState is enabled or disabled.
The value alarmOutstanding generically indicates that an alarm of
some severity is outstanding against the component.
Description of bits:
underRepair(0)
critical(1)
major(2)
minor(3)
alarmOutstanding(4)ro OCTET STRING .1.3.6.1.4.1.562.36.2.1.70.11.1.7 |
mscFrNniStandbyStatusIf supported by the component, this attribute indicates the OSI
Standby status of the component.
The value notSet indicates that either the attribute is not supported
or that none of the status conditions described below are present.
Note that this is a non-standard value, used because the original
specification indicated this attribute was set-valued and thus, did not
provide a value to indicate that none of the other three are
applicable.
The value hotStandby indicates that the resource is not providing
service but will be immediately able to take over the role of the
resource to be backed up, without initialization activity, and
containing the same information as the resource to be backed up.
The value coldStandby indicates the resource is a backup for
another resource but will not be immediately able to take over the
role of the backed up resource and will require some initialization
activity.
The value providingService indicates that this component, as a
backup resource, is currently backing up another resource.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.11.1.8 |
mscFrNniUnknownStatusThis attribute indicates the OSI Unknown status of the component.
The value false indicates that all of the other OSI State and Status
attribute values can be considered accurate.
The value true indicates that the actual state of the component is not
known for sure.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.11.1.9 |
mscFrNniStatsTableThis group contains the statistics about the operational behaviour of
the service at the interface level. SEQUENCE OF MscFrNniStatsEntry .1.3.6.1.4.1.562.36.2.1.70.12 |
mscFrNniStatsEntryAn entry in the mscFrNniStatsTable. MscFrNniStatsEntry .1.3.6.1.4.1.562.36.2.1.70.12.1 |
mscFrNniLastUnknownDlciThis attribute identifies the most recent DLCI which user frames
were received on for which a DLCI has not been provisioned on the
port.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.12.1.1 |
mscFrNniUnknownDlciFramesFromIfThis attribute contains a count of the number of frames received
from the interface with an unknown DLCI (DLCI which is not
provisioned). When the maximum is exceeded the count wraps to
zero.ro Counter32 .1.3.6.1.4.1.562.36.2.1.70.12.1.2 |
mscFrNniInvalidHeaderFramesFromIfThis attribute counts the number of frames received from the
interface with an invalid header format. When the maximum is
exceeded the count wraps to zero.ro Counter32 .1.3.6.1.4.1.562.36.2.1.70.12.1.3 |
mscFrNniIfEntryTableThis group contains the provisionable attributes for the ifEntry. SEQUENCE OF MscFrNniIfEntryEntry .1.3.6.1.4.1.562.36.2.1.70.13 |
mscFrNniIfEntryEntryAn entry in the mscFrNniIfEntryTable. MscFrNniIfEntryEntry .1.3.6.1.4.1.562.36.2.1.70.13.1 |
mscFrNniIfAdminStatusThe desired state of the interface. The up state indicates the
interface is operational. The down state indicates the interface is not
operational. The testing state indicates that no operational packets
can be passed.rw Enumeration .1.3.6.1.4.1.562.36.2.1.70.13.1.1 |
mscFrNniIfIndexThis is the index for the IfEntry. Its value is automatically initialized
during the provisioning process.ro InterfaceIndex .1.3.6.1.4.1.562.36.2.1.70.13.1.2 |
mscFrNniOperStatusTableThis group includes the Operational Status attribute. This attribute
defines the current operational state of this component. SEQUENCE OF MscFrNniOperStatusEntry .1.3.6.1.4.1.562.36.2.1.70.14 |
mscFrNniOperStatusEntryAn entry in the mscFrNniOperStatusTable. MscFrNniOperStatusEntry .1.3.6.1.4.1.562.36.2.1.70.14.1 |
mscFrNniSnmpOperStatusThe current state of the interface. The up state indicates the
interface is operational and capable of forwarding packets. The
down state indicates the interface is not operational, thus unable to
forward packets. testing state indicates that no operational packets
can be passed.ro Enumeration .1.3.6.1.4.1.562.36.2.1.70.14.1.1 |
mscFrNniEmissionPriorityQsTableThis group contains the provisionable attribute to specifie the
number of Frame Relay egress emission priority queues to be used
on that Frame Relay Interface SEQUENCE OF MscFrNniEmissionPriorityQsEntry .1.3.6.1.4.1.562.36.2.1.70.15 |
mscFrNniEmissionPriorityQsEntryAn entry in the mscFrNniEmissionPriorityQsTable. MscFrNniEmissionPriorityQsEntry .1.3.6.1.4.1.562.36.2.1.70.15.1 |
mscFrNniNumberOfEmissionQsThis attribute specifies the number of egress emission priority
queues that will be used for that Frame Relay interface. The
possible values of this attribute are 2 or 4:
For V.35, V.11, HSSI, E1, DS1, E3, DS3 or 8pDS1 the possible
values are: 2 (in which case they are hardware queues), or 4 (in
which case they are software queues).
For DS1C, E1C or DS3C the possible values are 2, 4 (in all cases
they are software queues).rw Unsigned32 (2 | 4) .1.3.6.1.4.1.562.36.2.1.70.15.1.1 |
mscFrNniCa OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.1.70.101 |
mscFrNniCaRowStatusTableThis entry controls the addition and deletion of
mscFrNniCa components. SEQUENCE OF MscFrNniCaRowStatusEntry .1.3.6.1.4.1.562.36.2.1.70.101.1 |
mscFrNniCaRowStatusEntryA single entry in the table represents a single
mscFrNniCa component. MscFrNniCaRowStatusEntry .1.3.6.1.4.1.562.36.2.1.70.101.1.1 |
mscFrNniCaRowStatusThis variable is used as the basis for SNMP naming of
mscFrNniCa components.
These components cannot be added nor deleted.ro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.101.1.1.1 |
mscFrNniCaComponentNameThis variable provides the component's string name for
use with the ASCII Console Interfacero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.101.1.1.2 |
mscFrNniCaStorageTypeThis variable represents the storage type value for the
mscFrNniCa tables.ro StorageType (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.101.1.1.4 |
mscFrNniCaIndexThis variable represents the index for the mscFrNniCa tables. NonReplicated .1.3.6.1.4.1.562.36.2.1.70.101.1.1.10 |
mscFrNniCaTpm OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.1.70.101.2 |
mscFrNniCaTpmRowStatusTableThis entry controls the addition and deletion of
mscFrNniCaTpm components. SEQUENCE OF MscFrNniCaTpmRowStatusEntry .1.3.6.1.4.1.562.36.2.1.70.101.2.1 |
mscFrNniCaTpmRowStatusEntryA single entry in the table represents a single
mscFrNniCaTpm component. MscFrNniCaTpmRowStatusEntry .1.3.6.1.4.1.562.36.2.1.70.101.2.1.1 |
mscFrNniCaTpmRowStatusThis variable is used as the basis for SNMP naming of
mscFrNniCaTpm components.
These components can be added and deleted.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.101.2.1.1.1 |
mscFrNniCaTpmComponentNameThis variable provides the component's string name for
use with the ASCII Console Interfacero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.101.2.1.1.2 |
mscFrNniCaTpmStorageTypeThis variable represents the storage type value for the
mscFrNniCaTpm tables.ro StorageType (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.70.101.2.1.1.4 |
mscFrNniCaTpmIndexThis variable represents the index for the mscFrNniCaTpm tables. Integer32 .1.3.6.1.4.1.562.36.2.1.70.101.2.1.1.10 |
mscFrNniCaTpmProvTableThis attribute group contains the provisionable attributes of the Tpm
component at this interface. SEQUENCE OF MscFrNniCaTpmProvEntry .1.3.6.1.4.1.562.36.2.1.70.101.2.10 |
mscFrNniCaTpmProvEntryAn entry in the mscFrNniCaTpmProvTable. MscFrNniCaTpmProvEntry .1.3.6.1.4.1.562.36.2.1.70.101.2.10.1 |
mscFrNniCaTpmAssignedIngressBandwidthPoolThis attribute specifies the ingress bandwidth pool which is used to
support this transfer priority at this interface. When this attribute is
set to sameAsModule, the bandwidth pool that is used is obtained
from the assignedIngressBandwidthPool attribute under the Mod
Frs DprsNet Tpm/n component.
VALUES (
16 = sameAsModule
)rw Unsigned32 (0..15 | 16) .1.3.6.1.4.1.562.36.2.1.70.101.2.10.1.2 |
mscFrNniCaTpmAssignedEgressBandwidthPoolThis attribute specifies the egress bandwidth pool which is used to
support this transfer priority at this interface. When this attribute is
set to sameAsModule, the bandwidth pool that is used is obtained
from the assignedEgressBandwidthPool attribute under the Mod
Frs DprsNet Tpm/n component.
VALUES (
16 = sameAsModule
)rw Unsigned32 (0..15 | 16) .1.3.6.1.4.1.562.36.2.1.70.101.2.10.1.3 |
mscFrNniCaProvTableThis attribute group contains the common provisionable attributes
of the Ca component. SEQUENCE OF MscFrNniCaProvEntry .1.3.6.1.4.1.562.36.2.1.70.101.10 |
mscFrNniCaProvEntryAn entry in the mscFrNniCaProvTable. MscFrNniCaProvEntry .1.3.6.1.4.1.562.36.2.1.70.101.10.1 |
mscFrNniCaOverrideLinkRateThis attribute allows the link rate to be overridden for this interface.
This allows the user to specify a value other than the actual physical
link rate computed when a Framer component is provisioned.
When a VFramer component is provisioned, this attribute overrides
a link rate set to the maximum value supported by CAC .
This attribute serves to provide the user control on the amount of
bandwidth available for performing CAC.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.101.10.1.2 |
mscFrNniCaMaximumBandwidthPerCallThis attribute specifies the maximum bandwidth that can be
allocated per connection.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.101.10.1.3 |
mscFrNniCaIngressCacTableThis attribute group contains the common provisionable attributes
for ingress call admission control. SEQUENCE OF MscFrNniCaIngressCacEntry .1.3.6.1.4.1.562.36.2.1.70.101.11 |
mscFrNniCaIngressCacEntryAn entry in the mscFrNniCaIngressCacTable. MscFrNniCaIngressCacEntry .1.3.6.1.4.1.562.36.2.1.70.101.11.1 |
mscFrNniCaIngressApplyToCosThis attribute specifies which Classes of Service (CoS) have ingress
Call Admission Control (CAC) applied to them. Ingress CAC
applies only to swithced connections (SVCs and S-SPVCs).
none - Ingress CAC is turned off for all classes of service.
cirOnly - Ingress CAC is applied only to the CIR portion of a
connection's bandwidth requirements for CIR>0 classes of service.
cirAndEir - Ingress CAC is applied to both CIR and EIR portions
of a connections bandwidth requirements for all classes of service.rw Enumeration .1.3.6.1.4.1.562.36.2.1.70.101.11.1.2 |
mscFrNniCaIngressMaximumEirOnlyCallsThis attribute specifies the maximum number of connections in the
ingress direction with EIR only traffic that can be up at a given
time.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.101.11.1.4 |
mscFrNniCaEgressCacTableThis attribute group contains the common provisionable attributes
for egress call admission control. SEQUENCE OF MscFrNniCaEgressCacEntry .1.3.6.1.4.1.562.36.2.1.70.101.12 |
mscFrNniCaEgressCacEntryAn entry in the mscFrNniCaEgressCacTable. MscFrNniCaEgressCacEntry .1.3.6.1.4.1.562.36.2.1.70.101.12.1 |
mscFrNniCaEgressApplyToCosThis attribute specifies which Classes of Service (CoS) have egress
Call Admission Control (CAC) applied to them. Egress CAC
applies only to swithced connections (SVCs and S-SPVCs).
none - Egress CAC is turned off for all classes of service.
cirOnly - Egress CAC is applied only to the CIR portion of a
connection's bandwidth requirements for CIR>0 classes of service.
cirAndEir - Egress CAC is applied to both CIR and EIR portions of
a connections bandwidth requirements for all classes of service.rw Enumeration .1.3.6.1.4.1.562.36.2.1.70.101.12.1.2 |
mscFrNniCaEgressMaximumEirOnlyCallsThis attribute specifies the maximum number of connections in the
egress direction with EIR only traffic that can be up at a given time.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.101.12.1.4 |
mscFrNniCaOpTableThis attribute group contains the operational status of the Ca
component. SEQUENCE OF MscFrNniCaOpEntry .1.3.6.1.4.1.562.36.2.1.70.101.13 |
mscFrNniCaOpEntryAn entry in the mscFrNniCaOpTable. MscFrNniCaOpEntry .1.3.6.1.4.1.562.36.2.1.70.101.13.1 |
mscFrNniCaLinkRateThis attribute indicates the link rate used by both ingress and egress
CAC to calculate the effective bandwidth pool sizes.
If the provisionable attribute overrideLinkRate under this
component is 0, then the link rate reported is the actual link rate of
the port or channel. Otherwise, the link rate reported is the
overrideLinkRate under this component.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.101.13.1.2 |
mscFrNniCaNumberRejectedEgressCirPermConnThis attribute indicates the number of permanent connections (that
is, PVC and P-SPVC) that are rejected by egress CAC. A
connection is rejected by egress CAC if it requests more egress CIR
bandwidth than is available, and the egressApplyToCos attribute is
set to either cirOnly or cirAndEir.ro Gauge32 .1.3.6.1.4.1.562.36.2.1.70.101.13.1.681 |
mscFrNniCaNumberRejectedEgressEirPermConnThis attribute indicates the number of permanent connections (that
is, PVC and P-SPVC) that are rejected by egress CAC. A
connection is rejected by egress CAC if it requests more egress EIR
bandwidth than is available, and the egressApplyToCos attribute is
set to cirAndEir.ro Gauge32 .1.3.6.1.4.1.562.36.2.1.70.101.13.1.682 |
mscFrNniCaIngCirBPTablePort capacity is partitioned into 16 pools (pool 0 through pool 15)
for the ingress CIR traffic. This attribute specifies the percentage of
port capacity that is allowed for each pool. The percentage for each
pool ranges from 0% to 1000% of the link rate. It allows for under
or over subscription of the port. Under subscription occurs when the
sum of the percentages assigned to the 16 pools is less than 100%.
Over subscription occurs when the sum of the percentages for the
16 pools exceeds 100%.
The default is full sharing of port capacity with three pre-set
partitions. SEQUENCE OF MscFrNniCaIngCirBPEntry .1.3.6.1.4.1.562.36.2.1.70.101.666 |
mscFrNniCaIngCirBPEntryAn entry in the mscFrNniCaIngCirBPTable. MscFrNniCaIngCirBPEntry .1.3.6.1.4.1.562.36.2.1.70.101.666.1 |
mscFrNniCaIngCirBPIndexThis variable represents the mscFrNniCaIngCirBPTable
specific index for the mscFrNniCaIngCirBPTable. Integer32 .1.3.6.1.4.1.562.36.2.1.70.101.666.1.1 |
mscFrNniCaIngCirBPValueThis variable represents an individual value for the
mscFrNniCaIngCirBPTable.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.101.666.1.2 |
mscFrNniCaEgCirBpTablePort capacity is partitioned into 16 pools (pool 0 through pool 15)
for the egress CIR traffic. This attribute specifies the percentage of
port capacity that is allowed for each pool. The percentage for each
pool ranges from 0% to 1000% of the link rate. It allows for under
or over subscription of the port. Under subscription occurs when the
sum of the percentages assigned to the 16 pools is less than 100%.
Over subscription occurs when the sum of the percentages for the
16 pools exceeds 100%.
The default is full sharing of port capacity with three pre-set
partitions. SEQUENCE OF MscFrNniCaEgCirBpEntry .1.3.6.1.4.1.562.36.2.1.70.101.667 |
mscFrNniCaEgCirBpEntryAn entry in the mscFrNniCaEgCirBpTable. MscFrNniCaEgCirBpEntry .1.3.6.1.4.1.562.36.2.1.70.101.667.1 |
mscFrNniCaEgCirBpIndexThis variable represents the mscFrNniCaEgCirBpTable
specific index for the mscFrNniCaEgCirBpTable. Integer32 .1.3.6.1.4.1.562.36.2.1.70.101.667.1.1 |
mscFrNniCaEgCirBpValueThis variable represents an individual value for the
mscFrNniCaEgCirBpTable.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.101.667.1.2 |
mscFrNniCaIngCirPoolAdmitBwTableThis attribute indicates the total admitted CIR bandwidth from each
CIR bandwidth pool in the ingress direction. Each value is the sum
of the equivalent bit rates of the admitted connections. SEQUENCE OF MscFrNniCaIngCirPoolAdmitBwEntry .1.3.6.1.4.1.562.36.2.1.70.101.668 |
mscFrNniCaIngCirPoolAdmitBwEntryAn entry in the mscFrNniCaIngCirPoolAdmitBwTable. MscFrNniCaIngCirPoolAdmitBwEntry .1.3.6.1.4.1.562.36.2.1.70.101.668.1 |
mscFrNniCaIngCirPoolAdmitBwIndexThis variable represents the mscFrNniCaIngCirPoolAdmitBwTable
specific index for the mscFrNniCaIngCirPoolAdmitBwTable. Integer32 .1.3.6.1.4.1.562.36.2.1.70.101.668.1.1 |
mscFrNniCaIngCirPoolAdmitBwValueThis variable represents an individual value for the
mscFrNniCaIngCirPoolAdmitBwTable.ro Gauge32 .1.3.6.1.4.1.562.36.2.1.70.101.668.1.2 |
mscFrNniCaIngCirPoolAvailBwTableThis attribute indicates the remaining available CIR bandwidth in
each ingress CIR bandwidth pool. SEQUENCE OF MscFrNniCaIngCirPoolAvailBwEntry .1.3.6.1.4.1.562.36.2.1.70.101.669 |
mscFrNniCaIngCirPoolAvailBwEntryAn entry in the mscFrNniCaIngCirPoolAvailBwTable. MscFrNniCaIngCirPoolAvailBwEntry .1.3.6.1.4.1.562.36.2.1.70.101.669.1 |
mscFrNniCaIngCirPoolAvailBwIndexThis variable represents the mscFrNniCaIngCirPoolAvailBwTable
specific index for the mscFrNniCaIngCirPoolAvailBwTable. Integer32 .1.3.6.1.4.1.562.36.2.1.70.101.669.1.1 |
mscFrNniCaIngCirPoolAvailBwValueThis variable represents an individual value for the
mscFrNniCaIngCirPoolAvailBwTable.ro Gauge32 .1.3.6.1.4.1.562.36.2.1.70.101.669.1.2 |
mscFrNniCaEgCirPoolAdmitBwTableThis attribute indicates the total admitted CIR bandwidth from each
CIR bandwidth pool in the egress direction. Each value is the sum
of the equivalent bit rates of the admitted connections. SEQUENCE OF MscFrNniCaEgCirPoolAdmitBwEntry .1.3.6.1.4.1.562.36.2.1.70.101.670 |
mscFrNniCaEgCirPoolAdmitBwEntryAn entry in the mscFrNniCaEgCirPoolAdmitBwTable. MscFrNniCaEgCirPoolAdmitBwEntry .1.3.6.1.4.1.562.36.2.1.70.101.670.1 |
mscFrNniCaEgCirPoolAdmitBwIndexThis variable represents the mscFrNniCaEgCirPoolAdmitBwTable
specific index for the mscFrNniCaEgCirPoolAdmitBwTable. Integer32 .1.3.6.1.4.1.562.36.2.1.70.101.670.1.1 |
mscFrNniCaEgCirPoolAdmitBwValueThis variable represents an individual value for the
mscFrNniCaEgCirPoolAdmitBwTable.ro Gauge32 .1.3.6.1.4.1.562.36.2.1.70.101.670.1.2 |
mscFrNniCaEgCirPoolAvailBwTableThis attribute indicates the remaining available CIR bandwidth in
each egress CIR bandwidth pool. SEQUENCE OF MscFrNniCaEgCirPoolAvailBwEntry .1.3.6.1.4.1.562.36.2.1.70.101.671 |
mscFrNniCaEgCirPoolAvailBwEntryAn entry in the mscFrNniCaEgCirPoolAvailBwTable. MscFrNniCaEgCirPoolAvailBwEntry .1.3.6.1.4.1.562.36.2.1.70.101.671.1 |
mscFrNniCaEgCirPoolAvailBwIndexThis variable represents the mscFrNniCaEgCirPoolAvailBwTable
specific index for the mscFrNniCaEgCirPoolAvailBwTable. Integer32 .1.3.6.1.4.1.562.36.2.1.70.101.671.1.1 |
mscFrNniCaEgCirPoolAvailBwValueThis variable represents an individual value for the
mscFrNniCaEgCirPoolAvailBwTable.ro Gauge32 .1.3.6.1.4.1.562.36.2.1.70.101.671.1.2 |
mscFrNniCaIngEirBpTablePort capacity is partitioned into 16 pools (pool 0 through pool 15)
for the ingress EIR traffic. This attribute specifies the percentage of
port capacity that is allowed for each pool. The percentage for each
pool ranges from 0% to 1000% of the link rate. It allows for under
or over subscription of the port. Under subscription occurs when the
sum of the percentages assigned to the 16 pools is less than 100%.
Over subscription occurs when the sum of the percentages for the
16 pools exceeds 100%.
The default is full sharing of port capacity with three pre-set
partitions. SEQUENCE OF MscFrNniCaIngEirBpEntry .1.3.6.1.4.1.562.36.2.1.70.101.673 |
mscFrNniCaIngEirBpEntryAn entry in the mscFrNniCaIngEirBpTable. MscFrNniCaIngEirBpEntry .1.3.6.1.4.1.562.36.2.1.70.101.673.1 |
mscFrNniCaIngEirBpIndexThis variable represents the mscFrNniCaIngEirBpTable
specific index for the mscFrNniCaIngEirBpTable. Integer32 .1.3.6.1.4.1.562.36.2.1.70.101.673.1.1 |
mscFrNniCaIngEirBpValueThis variable represents an individual value for the
mscFrNniCaIngEirBpTable.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.101.673.1.2 |
mscFrNniCaEgEirBpTablePort capacity is partitioned into 16 pools (pool 0 through pool 15)
for the egress EIR traffic. This attribute specifies the percentage of
port capacity that is allowed for each pool. The percentage for each
pool ranges from 0% to 1000% of the link rate. It allows for under
or over subscription of the port. Under subscription occurs when the
sum of the percentages assigned to the 16 pools is less than 100%.
Over subscription occurs when the sum of the percentages for the
16 pools exceeds 100%.
The default is full sharing of port capacity with three pre-set
partitions. SEQUENCE OF MscFrNniCaEgEirBpEntry .1.3.6.1.4.1.562.36.2.1.70.101.674 |
mscFrNniCaEgEirBpEntryAn entry in the mscFrNniCaEgEirBpTable. MscFrNniCaEgEirBpEntry .1.3.6.1.4.1.562.36.2.1.70.101.674.1 |
mscFrNniCaEgEirBpIndexThis variable represents the mscFrNniCaEgEirBpTable
specific index for the mscFrNniCaEgEirBpTable. Integer32 .1.3.6.1.4.1.562.36.2.1.70.101.674.1.1 |
mscFrNniCaEgEirBpValueThis variable represents an individual value for the
mscFrNniCaEgEirBpTable.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.101.674.1.2 |
mscFrNniCaIngEirPoolAdmitBwTableThis attribute indicates the total admitted EIR bandwidth from each
EIR bandwidth pool in the ingress direction. Each value is the sum
of the equivalent bit rates of the admitted connections.
If the ingressApplyToCos attribute is set to none, all ingress CIR
bandwidth pools are set to 0. SEQUENCE OF MscFrNniCaIngEirPoolAdmitBwEntry .1.3.6.1.4.1.562.36.2.1.70.101.675 |
mscFrNniCaIngEirPoolAdmitBwEntryAn entry in the mscFrNniCaIngEirPoolAdmitBwTable. MscFrNniCaIngEirPoolAdmitBwEntry .1.3.6.1.4.1.562.36.2.1.70.101.675.1 |
mscFrNniCaIngEirPoolAdmitBwIndexThis variable represents the mscFrNniCaIngEirPoolAdmitBwTable
specific index for the mscFrNniCaIngEirPoolAdmitBwTable. Integer32 .1.3.6.1.4.1.562.36.2.1.70.101.675.1.1 |
mscFrNniCaIngEirPoolAdmitBwValueThis variable represents an individual value for the
mscFrNniCaIngEirPoolAdmitBwTable.ro Gauge32 .1.3.6.1.4.1.562.36.2.1.70.101.675.1.2 |
mscFrNniCaIngEirPoolAvailBwTableThis attribute indicates the remaining available EIR bandwidth in
each ingress EIR bandwidth pool.
If the ingressApplyToCos attribute is set to either none or cirOnly,
all ingress EIR bandwidth pools are set to 0. SEQUENCE OF MscFrNniCaIngEirPoolAvailBwEntry .1.3.6.1.4.1.562.36.2.1.70.101.676 |
mscFrNniCaIngEirPoolAvailBwEntryAn entry in the mscFrNniCaIngEirPoolAvailBwTable. MscFrNniCaIngEirPoolAvailBwEntry .1.3.6.1.4.1.562.36.2.1.70.101.676.1 |
mscFrNniCaIngEirPoolAvailBwIndexThis variable represents the mscFrNniCaIngEirPoolAvailBwTable
specific index for the mscFrNniCaIngEirPoolAvailBwTable. Integer32 .1.3.6.1.4.1.562.36.2.1.70.101.676.1.1 |
mscFrNniCaIngEirPoolAvailBwValueThis variable represents an individual value for the
mscFrNniCaIngEirPoolAvailBwTable.ro Gauge32 .1.3.6.1.4.1.562.36.2.1.70.101.676.1.2 |
mscFrNniCaEgEirPoolAdmitBwTableThis attribute indicates the total admitted EIR bandwidth from each
EIR bandwidth pool in the egress direction. Each value is the sum
of the equivalent bit rates of the admitted connections.
If the egressApplyToCos attribute is set to none, all egress CIR
bandwidth pools are set to 0. SEQUENCE OF MscFrNniCaEgEirPoolAdmitBwEntry .1.3.6.1.4.1.562.36.2.1.70.101.677 |
mscFrNniCaEgEirPoolAdmitBwEntryAn entry in the mscFrNniCaEgEirPoolAdmitBwTable. MscFrNniCaEgEirPoolAdmitBwEntry .1.3.6.1.4.1.562.36.2.1.70.101.677.1 |
mscFrNniCaEgEirPoolAdmitBwIndexThis variable represents the mscFrNniCaEgEirPoolAdmitBwTable
specific index for the mscFrNniCaEgEirPoolAdmitBwTable. Integer32 .1.3.6.1.4.1.562.36.2.1.70.101.677.1.1 |
mscFrNniCaEgEirPoolAdmitBwValueThis variable represents an individual value for the
mscFrNniCaEgEirPoolAdmitBwTable.ro Gauge32 .1.3.6.1.4.1.562.36.2.1.70.101.677.1.2 |
mscFrNniCaEgEirPoolAvailBwTableThis attribute indicates the remaining available EIR bandwidth in
each egress EIR bandwidth pool.
If the egressApplyToCos attribute is set to either none or cirOnly,
all egress EIR bandwidth pools are set to 0. SEQUENCE OF MscFrNniCaEgEirPoolAvailBwEntry .1.3.6.1.4.1.562.36.2.1.70.101.678 |
mscFrNniCaEgEirPoolAvailBwEntryAn entry in the mscFrNniCaEgEirPoolAvailBwTable. MscFrNniCaEgEirPoolAvailBwEntry .1.3.6.1.4.1.562.36.2.1.70.101.678.1 |
mscFrNniCaEgEirPoolAvailBwIndexThis variable represents the mscFrNniCaEgEirPoolAvailBwTable
specific index for the mscFrNniCaEgEirPoolAvailBwTable. Integer32 .1.3.6.1.4.1.562.36.2.1.70.101.678.1.1 |
mscFrNniCaEgEirPoolAvailBwValueThis variable represents an individual value for the
mscFrNniCaEgEirPoolAvailBwTable.ro Gauge32 .1.3.6.1.4.1.562.36.2.1.70.101.678.1.2 |
mscFrNniFrmToIfByQueueTableThis attribute counts the total number of frames transmitted to the
interface per egress emission priority queue since the component
has been activated. There is potientially a maximum of 4 emission
priority queues. The number of available egress queues varies
according to the value of the provisionable attribute
numberOfEmissionQs. Egress queue 0 has the lowest priority, while
egress queue 3 has the highest priority. The queue values
are only indicated when the numberOfEmissionQs is set to 4
queues. SEQUENCE OF MscFrNniFrmToIfByQueueEntry .1.3.6.1.4.1.562.36.2.1.70.341 |
mscFrNniFrmToIfByQueueEntryAn entry in the mscFrNniFrmToIfByQueueTable. MscFrNniFrmToIfByQueueEntry .1.3.6.1.4.1.562.36.2.1.70.341.1 |
mscFrNniFrmToIfByQueueIndexThis variable represents the index for the mscFrNniFrmToIfByQueueTable. Integer32 .1.3.6.1.4.1.562.36.2.1.70.341.1.1 |
mscFrNniFrmToIfByQueueValueThis variable represents an individual value for the
mscFrNniFrmToIfByQueueTable.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.341.1.2 |
mscFrNniOctetToIfByQueueTableThis attribute counts the total number of octets transmitted from the
service to the interface per emission priority queue since the
component has been activated. There is potientially a maximum of
4 emission priority queues. The number of available egress queues
varies according to the value of the provisionable attribute
numberOfEmissionQs. Egress queue 0 has the lowest priority, while
egress queue 3 has the highest priority. SEQUENCE OF MscFrNniOctetToIfByQueueEntry .1.3.6.1.4.1.562.36.2.1.70.342 |
mscFrNniOctetToIfByQueueEntryAn entry in the mscFrNniOctetToIfByQueueTable. MscFrNniOctetToIfByQueueEntry .1.3.6.1.4.1.562.36.2.1.70.342.1 |
mscFrNniOctetToIfByQueueIndexThis variable represents the index for the mscFrNniOctetToIfByQueueTable. Integer32 .1.3.6.1.4.1.562.36.2.1.70.342.1.1 |
mscFrNniOctetToIfByQueueValueThis variable represents an individual value for the
mscFrNniOctetToIfByQueueTable.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.70.342.1.2 |
frameRelayNniMIB OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.2.23 |
IMPORTS Unknown .1.3.6.1.4.1.562.36.2.2.23 |
frameRelayNniGroup OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.2.23.1 |
frameRelayNniGroupCA OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.2.23.1.1 |
frameRelayNniGroupCA02 OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.2.23.1.1.3 |
frameRelayNniGroupCA02A OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.2.23.1.1.3.2 |
frameRelayNniCapabilities OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.2.23.3 |
frameRelayNniCapabilitiesCA OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.2.23.3.1 |
frameRelayNniCapabilitiesCA02 OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.2.23.3.1.3 |
frameRelayNniCapabilitiesCA02A OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.2.23.3.1.3.2 |