Nortel-MsCarrier-MscPassport-CircuitEmulationServiceMIB
AI MIB Summary
Standard SNMP MIB module defining data structures for Nortel-MsCarrier-MscPassport-CircuitEmulationServiceMIB.
228
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
228 total| Object Name |
|---|
mscAal1Ces OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.1.119 |
mscAal1CesRowStatusTableThis entry controls the addition and deletion of
mscAal1Ces components. SEQUENCE OF MscAal1CesRowStatusEntry .1.3.6.1.4.1.562.36.2.1.119.1 |
mscAal1CesRowStatusEntryA single entry in the table represents a single
mscAal1Ces component. MscAal1CesRowStatusEntry .1.3.6.1.4.1.562.36.2.1.119.1.1 |
mscAal1CesRowStatusThis variable is used as the basis for SNMP naming of
mscAal1Ces components.
These components can be added and deleted.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.119.1.1.1 |
mscAal1CesComponentNameThis variable provides the component's string name for
use with the ASCII Console Interfacero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.119.1.1.2 |
mscAal1CesStorageTypeThis variable represents the storage type value for the
mscAal1Ces tables.ro StorageType (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.119.1.1.4 |
mscAal1CesIndexThis variable represents the index for the mscAal1Ces tables. Integer32 .1.3.6.1.4.1.562.36.2.1.119.1.1.10 |
mscAal1CesNap OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.1.119.2 |
mscAal1CesNapRowStatusTableThis entry controls the addition and deletion of
mscAal1CesNap components. SEQUENCE OF MscAal1CesNapRowStatusEntry .1.3.6.1.4.1.562.36.2.1.119.2.1 |
mscAal1CesNapRowStatusEntryA single entry in the table represents a single
mscAal1CesNap component. MscAal1CesNapRowStatusEntry .1.3.6.1.4.1.562.36.2.1.119.2.1.1 |
mscAal1CesNapRowStatusThis variable is used as the basis for SNMP naming of
mscAal1CesNap components.
These components can be added and deleted.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.119.2.1.1.1 |
mscAal1CesNapComponentNameThis variable provides the component's string name for
use with the ASCII Console Interfacero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.119.2.1.1.2 |
mscAal1CesNapStorageTypeThis variable represents the storage type value for the
mscAal1CesNap tables.ro StorageType (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.119.2.1.1.4 |
mscAal1CesNapIndexThis variable represents the index for the mscAal1CesNap tables. NonReplicated .1.3.6.1.4.1.562.36.2.1.119.2.1.1.10 |
mscAal1CesNapProvTableThis group contains the provisioning data for the
NailedUpAdaptationPoint component. SEQUENCE OF MscAal1CesNapProvEntry .1.3.6.1.4.1.562.36.2.1.119.2.10 |
mscAal1CesNapProvEntryAn entry in the mscAal1CesNapProvTable. MscAal1CesNapProvEntry .1.3.6.1.4.1.562.36.2.1.119.2.10.1 |
mscAal1CesNapAtmConnectionThis attribute specifies the identity of the component to which the
NailedUpAdaptationPoint is linked. This is an AtmIf Vcc
NailedUpEndPoint or an AtmIf Vpt Vcc NailedUpEndPoint (the
AAL1 cells are transported off the switch over an ATM UNI, where
they are routed to the appropriate AAL1 entity at the other end by
the ATM bearer service).rw Link .1.3.6.1.4.1.562.36.2.1.119.2.10.1.1 |
mscAal1CesAep OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.1.119.3 |
mscAal1CesAepRowStatusTableThis entry controls the addition and deletion of
mscAal1CesAep components. SEQUENCE OF MscAal1CesAepRowStatusEntry .1.3.6.1.4.1.562.36.2.1.119.3.1 |
mscAal1CesAepRowStatusEntryA single entry in the table represents a single
mscAal1CesAep component. MscAal1CesAepRowStatusEntry .1.3.6.1.4.1.562.36.2.1.119.3.1.1 |
mscAal1CesAepRowStatusThis variable is used as the basis for SNMP naming of
mscAal1CesAep components.
These components can be added and deleted.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.119.3.1.1.1 |
mscAal1CesAepComponentNameThis variable provides the component's string name for
use with the ASCII Console Interfacero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.119.3.1.1.2 |
mscAal1CesAepStorageTypeThis variable represents the storage type value for the
mscAal1CesAep tables.ro StorageType (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.119.3.1.1.4 |
mscAal1CesAepIndexThis variable represents the index for the mscAal1CesAep tables. NonReplicated .1.3.6.1.4.1.562.36.2.1.119.3.1.1.10 |
mscAal1CesAepProvEndPointAddrTableThis group contains NSAP address provisioning data for
components using switched virtual circuits. SEQUENCE OF MscAal1CesAepProvEndPointAddrEntry .1.3.6.1.4.1.562.36.2.1.119.3.10 |
mscAal1CesAepProvEndPointAddrEntryAn entry in the mscAal1CesAepProvEndPointAddrTable. MscAal1CesAepProvEndPointAddrEntry .1.3.6.1.4.1.562.36.2.1.119.3.10.1 |
mscAal1CesAepExpectedRemoteAddressThis attribute specifies the expected remote address prefix for an
incoming connection setup request.
If expectedRemoteAddress is not empty, only matching connections
will be considered for acceptance. If expectedRemoteAddress is 40
characters long, the remote address must match exactly to be
accepted. If expectedRemoteAddress is less than 40 characters long,
the remote address must begin with expectedRemoteAddress to be
accepted.
If expectedRemoteAddress is empty, the component will process
connection requests from any remote address.rw AsciiString .1.3.6.1.4.1.562.36.2.1.119.3.10.1.1 |
mscAal1CesAepLocalAddressThis attribute specifies the local NSAP address.
If the switch prefix (the nodePrefix attribute of the ModuleData
component) has been provisioned, a default value for localAddress
based on nodePrefix will be provided.
If ModuleData nodePrefix has not been provisioned and one or
more alternate switch prefixes (the alternatePorsPrefixes attribute
of the ModuleData component) have been provisioned, a default
value for localAddress based on the first provisioned
alternatePorsPrefix value will be provided.
If no switch prefixes have been provisioned, localAddress will
default to an empty string. To obtain a valid default localAddress in
this case, either or both of the ModuleData nodePrefix and
ModuleData alternatePorsPrefixes attributes must be provisioned,
and this end point component must then be deleted and re-added.rw AsciiString .1.3.6.1.4.1.562.36.2.1.119.3.10.1.2 |
mscAal1CesAepProvTableThis group contains the provisioning data specific to the
ActiveEndPoint component. SEQUENCE OF MscAal1CesAepProvEntry .1.3.6.1.4.1.562.36.2.1.119.3.11 |
mscAal1CesAepProvEntryAn entry in the mscAal1CesAepProvTable. MscAal1CesAepProvEntry .1.3.6.1.4.1.562.36.2.1.119.3.11.1 |
mscAal1CesAepAddressToCallThis attribute specifies the remote NSAP address which this
ActiveEndPoint will call.rw AsciiString .1.3.6.1.4.1.562.36.2.1.119.3.11.1.1 |
mscAal1CesAepRoutingOptionThis attribute specifies the type of routing to use for establishing the
connection:
AAL1 cards accept only porsOnly.
Multi-Service Access cards accept all four options.
porsOnly means that only the Path Oriented Routing System may
be used in establishing a connection.
atmOnly means that only the native ATM Routing may be used in
establishing a connection.
porsFirst means that the switch tries to establish a connection using
the Path Oriented Routing System first, and, if the connection
cannot be established, it tries native ATM Routing instead.
atmFirst means that the switch tries to establish a connection using
native ATM Routing first, and, if the connection cannot be
established, it tries the Path Oriented Routing System instead.rw Enumeration .1.3.6.1.4.1.562.36.2.1.119.3.11.1.2 |
mscAal1CesAepProfileThis attribute specifies the PORS routing profile to use for this
connection.
If profile is empty, PORS will provide a default profile.rw Link .1.3.6.1.4.1.562.36.2.1.119.3.11.1.3 |
mscAal1CesAepFirstRetryIntervalThis attribute specifies the time to wait, in seconds, before
attempting to establish the connection after the first failed attempt.
The time to wait between subsequent call attempts will generally
differ due to a backoff scheme.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.119.3.11.1.4 |
mscAal1CesAepRetryLimitretryLimit specifies the maximum number of consecutive
unsuccessful connection setup attempts that may be made before
further attempts are abandoned.
If this limit is reached, the Restart verb may be used to restart
connection attempts.
If retryLimit is 0, there is no limit; attempts will continue
indefinitely until a successful connection is established.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.119.3.11.1.5 |
mscAal1CesAepActiveEndPointTypeactiveEndPointType specifies the type of end point: svc or softPvc.
The default is svc.
When activeEndPointType is svc, calledVpiVci is not relevant.
When activeEndPointType is softPVC, routingOption must be
atmOnly, and profile, firstRetryInterval, and retryLimit are not
relevant.rw Enumeration .1.3.6.1.4.1.562.36.2.1.119.3.11.1.6 |
mscAal1CesAepCalledVpiVcicalledVpiVci specifies the identity of the PVC at the remote ATM
node on which the softPVC connection terminates.
calledVpiVci is relevant only when activeEndPointType is set to
softPVC.
The default value is 0.1rw IntegerSequence .1.3.6.1.4.1.562.36.2.1.119.3.11.1.7 |
mscAal1CesAepEpOperTableThis group contains general operational attributes for components
using switched virtual circuits. SEQUENCE OF MscAal1CesAepEpOperEntry .1.3.6.1.4.1.562.36.2.1.119.3.12 |
mscAal1CesAepEpOperEntryAn entry in the mscAal1CesAepEpOperTable. MscAal1CesAepEpOperEntry .1.3.6.1.4.1.562.36.2.1.119.3.12.1 |
mscAal1CesAepRemoteAddressremoteAddress is the address of the remote end point.
If a connection is currently established, remoteAddress will contain
the address of the remote end point.
If a connection is not established, remoteAddress will be Unknown.ro AsciiString .1.3.6.1.4.1.562.36.2.1.119.3.12.1.1 |
mscAal1CesAepLastTearDownCauselastTearDownCause indicates the cause of the last connection tear
down.
The values are as defined in the ATM Forum ATM User-Network
Interface (UNI) Specification.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.119.3.12.1.2 |
mscAal1CesAepLastTearDownDiagnosticlastTearDownDiagnostic provides a diagnostic to supplement the
lastTearDownCause attribute.ro AsciiString .1.3.6.1.4.1.562.36.2.1.119.3.12.1.3 |
mscAal1CesAepOutTableThis group contains status information about the AAL1 Circuit
Emulation Service ActiveEndPoint component. SEQUENCE OF MscAal1CesAepOutEntry .1.3.6.1.4.1.562.36.2.1.119.3.13 |
mscAal1CesAepOutEntryAn entry in the mscAal1CesAepOutTable. MscAal1CesAepOutEntry .1.3.6.1.4.1.562.36.2.1.119.3.13.1 |
mscAal1CesAepSvcStatussvcStatus indicates the status of the incoming and outgoing
connections.
When this attribute has the value initialising, it indicates that the
component is initialising when first created; a connection has not
been established, and no incoming setup requests will be processed.
When this attribute has the value connecting, it indicates that a
connection has not yet been established, but that incoming setup
requests will be processed.
When this attribute has the value connected, it indicates that a
connection has been established.
When this attribute has the value retriesExhausted, it indicates that
retryLimit consecutive connection setup attempts have failed, and
the connection procedure has been aborted.
When this attribute has the value idle, it indicates that a connection
has not been established, and that no incoming setup requests will
be processed.
When this attribute has the value failed, it indicates that the
connections is in a state other than those described above.ro Enumeration .1.3.6.1.4.1.562.36.2.1.119.3.13.1.1 |
mscAal1CesAepLastSetupFailureCauselastSetupFailureCause indicates the cause of the last connection
setup failure.
The values are as defined in the ATM Forum ATM User-
Network Interface (UNI) Specification.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.119.3.13.1.2 |
mscAal1CesAepLastSetupFailureDiagnosticlastSetupFailureDiagnostic provides a diagnostic to supplement the
lastSetupFailureCause attribute.ro AsciiString .1.3.6.1.4.1.562.36.2.1.119.3.13.1.3 |
mscAal1CesAepRetryTimeRemainingretryTimerValue is the current value of the retry timer for this
connection; it indicates the number of seconds before the next
connection attempt will be made. retryTimerValue is initialized
when a connection attempt fails.
When retryTimerValue reaches 0, an attempt will be made to
establish the connection.
When the timer is not running, for example when the connection
has been established, retryTimerValue will be 0.ro Counter32 .1.3.6.1.4.1.562.36.2.1.119.3.13.1.4 |
mscAal1CesAepRetryFailuresretryFailures counts the number of consecutive failed connection
attempts.
retryFailures is reset to 0 whenever a connection is successfully
established, or the connection is restarted using the Restart verb.
The counter wraps when the maximum value is exceeded.ro Counter32 .1.3.6.1.4.1.562.36.2.1.119.3.13.1.5 |
mscAal1CesPep OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.1.119.4 |
mscAal1CesPepRowStatusTableThis entry controls the addition and deletion of
mscAal1CesPep components. SEQUENCE OF MscAal1CesPepRowStatusEntry .1.3.6.1.4.1.562.36.2.1.119.4.1 |
mscAal1CesPepRowStatusEntryA single entry in the table represents a single
mscAal1CesPep component. MscAal1CesPepRowStatusEntry .1.3.6.1.4.1.562.36.2.1.119.4.1.1 |
mscAal1CesPepRowStatusThis variable is used as the basis for SNMP naming of
mscAal1CesPep components.
These components can be added and deleted.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.119.4.1.1.1 |
mscAal1CesPepComponentNameThis variable provides the component's string name for
use with the ASCII Console Interfacero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.119.4.1.1.2 |
mscAal1CesPepStorageTypeThis variable represents the storage type value for the
mscAal1CesPep tables.ro StorageType (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.119.4.1.1.4 |
mscAal1CesPepIndexThis variable represents the index for the mscAal1CesPep tables. NonReplicated .1.3.6.1.4.1.562.36.2.1.119.4.1.1.10 |
mscAal1CesPepProvEndPointAddrTableThis group contains NSAP address provisioning data for
components using switched virtual circuits. SEQUENCE OF MscAal1CesPepProvEndPointAddrEntry .1.3.6.1.4.1.562.36.2.1.119.4.10 |
mscAal1CesPepProvEndPointAddrEntryAn entry in the mscAal1CesPepProvEndPointAddrTable. MscAal1CesPepProvEndPointAddrEntry .1.3.6.1.4.1.562.36.2.1.119.4.10.1 |
mscAal1CesPepExpectedRemoteAddressThis attribute specifies the expected remote address prefix for an
incoming connection setup request.
If expectedRemoteAddress is not empty, only matching connections
will be considered for acceptance. If expectedRemoteAddress is 40
characters long, the remote address must match exactly to be
accepted. If expectedRemoteAddress is less than 40 characters long,
the remote address must begin with expectedRemoteAddress to be
accepted.
If expectedRemoteAddress is empty, the component will process
connection requests from any remote address.rw AsciiString .1.3.6.1.4.1.562.36.2.1.119.4.10.1.1 |
mscAal1CesPepLocalAddressThis attribute specifies the local NSAP address.
If the switch prefix (the nodePrefix attribute of the ModuleData
component) has been provisioned, a default value for localAddress
based on nodePrefix will be provided.
If ModuleData nodePrefix has not been provisioned and one or
more alternate switch prefixes (the alternatePorsPrefixes attribute
of the ModuleData component) have been provisioned, a default
value for localAddress based on the first provisioned
alternatePorsPrefix value will be provided.
If no switch prefixes have been provisioned, localAddress will
default to an empty string. To obtain a valid default localAddress in
this case, either or both of the ModuleData nodePrefix and
ModuleData alternatePorsPrefixes attributes must be provisioned,
and this end point component must then be deleted and re-added.rw AsciiString .1.3.6.1.4.1.562.36.2.1.119.4.10.1.2 |
mscAal1CesPepEpOperTableThis group contains general operational attributes for components
using switched virtual circuits. SEQUENCE OF MscAal1CesPepEpOperEntry .1.3.6.1.4.1.562.36.2.1.119.4.11 |
mscAal1CesPepEpOperEntryAn entry in the mscAal1CesPepEpOperTable. MscAal1CesPepEpOperEntry .1.3.6.1.4.1.562.36.2.1.119.4.11.1 |
mscAal1CesPepRemoteAddressremoteAddress is the address of the remote end point.
If a connection is currently established, remoteAddress will contain
the address of the remote end point.
If a connection is not established, remoteAddress will be Unknown.ro AsciiString .1.3.6.1.4.1.562.36.2.1.119.4.11.1.1 |
mscAal1CesPepLastTearDownCauselastTearDownCause indicates the cause of the last connection tear
down.
The values are as defined in the ATM Forum ATM User-Network
Interface (UNI) Specification.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.119.4.11.1.2 |
mscAal1CesPepLastTearDownDiagnosticlastTearDownDiagnostic provides a diagnostic to supplement the
lastTearDownCause attribute.ro AsciiString .1.3.6.1.4.1.562.36.2.1.119.4.11.1.3 |
mscAal1CesPepPassiveOperTableThis group contains status information about the AAL1 Circuit
Emulation Service PassiveEndPoint component. SEQUENCE OF MscAal1CesPepPassiveOperEntry .1.3.6.1.4.1.562.36.2.1.119.4.12 |
mscAal1CesPepPassiveOperEntryAn entry in the mscAal1CesPepPassiveOperTable. MscAal1CesPepPassiveOperEntry .1.3.6.1.4.1.562.36.2.1.119.4.12.1 |
mscAal1CesPepSvcStatussvcStatus indicates the status of the incoming connection.
When this attribute has the value initialising, it indicates that the
component is initialising when first created; a connection has not
been established, and no incoming setup requests will be processed.
When this attribute has the value connecting, it indicates that a
connection has not yet been establised, but that incoming setup
requests will be processed.
When this attribute has the value connected, it indicates that a
connection has been established.
When this attribute has the value idle, it indicates that a connection
has not been established, and that no incoming setup requests will
be processed.
When this attribute has the value failed, it indicates that the
connections is in a state other than those described above.ro Enumeration .1.3.6.1.4.1.562.36.2.1.119.4.12.1.1 |
mscAal1CesLCo OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.1.119.5 |
mscAal1CesLCoRowStatusTableThis entry controls the addition and deletion of
mscAal1CesLCo components. SEQUENCE OF MscAal1CesLCoRowStatusEntry .1.3.6.1.4.1.562.36.2.1.119.5.1 |
mscAal1CesLCoRowStatusEntryA single entry in the table represents a single
mscAal1CesLCo component. MscAal1CesLCoRowStatusEntry .1.3.6.1.4.1.562.36.2.1.119.5.1.1 |
mscAal1CesLCoRowStatusThis variable is used as the basis for SNMP naming of
mscAal1CesLCo components.
These components cannot be added nor deleted.ro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.119.5.1.1.1 |
mscAal1CesLCoComponentNameThis variable provides the component's string name for
use with the ASCII Console Interfacero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.119.5.1.1.2 |
mscAal1CesLCoStorageTypeThis variable represents the storage type value for the
mscAal1CesLCo tables.ro StorageType (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.119.5.1.1.4 |
mscAal1CesLCoIndexThis variable represents the index for the mscAal1CesLCo tables. NonReplicated .1.3.6.1.4.1.562.36.2.1.119.5.1.1.10 |
mscAal1CesLCoPathDataTableThis group contains all operational attributes for the path oriented
LCo. SEQUENCE OF MscAal1CesLCoPathDataEntry .1.3.6.1.4.1.562.36.2.1.119.5.10 |
mscAal1CesLCoPathDataEntryAn entry in the mscAal1CesLCoPathDataTable. MscAal1CesLCoPathDataEntry .1.3.6.1.4.1.562.36.2.1.119.5.10.1 |
mscAal1CesLCoStateThis attribute reflects the current state of the connection. The
pathDown state indicates a connection that has no remote end
provisioned or the application has not yet signalled for a path. The
selectingRoute state occurs when a request has been sent to route
selector and it has not yet responded. The connectingState occurs
while a path is being established. The pathUp state is the normal
operational state of a path. The pathDownRetrying state indicates a
path that attempted route selection but received no route and is now
waiting to retry route selection again.ro Enumeration .1.3.6.1.4.1.562.36.2.1.119.5.10.1.1 |
mscAal1CesLCoOverrideRemoteNameIf set and the current PLC remoteName is blank this remoteName
will override the blank PLC remoteName. Usually you would set
this attribute and then lock/unlock the service component which
will result in this new overrideRemoteName being used as if it had
been provisioned into the PLC remoteName. The advantage of this
attribute is that the connection's remoteName can be changed
immediately without having to 'activate prov' but the disadvantage
is that the overrideRemoteName is not permanent and if the card or
switch is reset the override will be lost.rw AsciiString .1.3.6.1.4.1.562.36.2.1.119.5.10.1.2 |
mscAal1CesLCoEndThis attribute identifies whether this is the calling or called end of
the path.ro Enumeration .1.3.6.1.4.1.562.36.2.1.119.5.10.1.3 |
mscAal1CesLCoCostMetricThis attribute gives the route's total cost metric. It is calculated as
the sum of the cost metric of all trunks in the path at the time the
connection was established. The cost metric of a trunk is defined by
the trunkCost attribute of the Trunk component. The costMetric for
an LCo that is originated and terminated on the same module is 0.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.119.5.10.1.4 |
mscAal1CesLCoDelayMetricThis attribute gives the total delay of the route as the one way delay
for a 512 byte packet. It is calculated as the sum of the delays of all
trunks in the path stored in topology at the time the connection was
established. The delay for an LCo that is originated and terminated
on the same module is 0.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.119.5.10.1.5 |
mscAal1CesLCoRoundTripDelayThis attribute contains the time taken for a packet (cell) of 44 bytes
to be transmitted to the remote LCo and return to this LCo. The
number reported is given in milliseconds to the nearest millisecond.
A value of one millisecond is reported if the time is less than 1
millisecond even though the delay may be less than 1 Millisecond
when the LCo is originated and terminated on the same module.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.119.5.10.1.6 |
mscAal1CesLCoSetupPriorityThis attribute gives the priority at which the current path is
established. Zero is the highest priority and four is the lowest. The
holdingPriority, a complementary attribute of this component,
indicates the priority a path maintains once it is established.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.119.5.10.1.7 |
mscAal1CesLCoHoldingPriorityThis attribute gives the priority at which a path holds its current
path once the path is established. Zero is the highest priority and
four is the lowest. The setupPriority, a complementary attribute,
indicates the priority of a path at establishment time.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.119.5.10.1.8 |
mscAal1CesLCoRequiredTxBandwidthThis attribute gives the actual bandwidth (in bits per second)
reserved by this path on each of the trunks of its route. This attribute
represents the bandwidth for traffic outgoing to the remote end
point. The originating end of the connection determines this value.ro Gauge32 .1.3.6.1.4.1.562.36.2.1.119.5.10.1.9 |
mscAal1CesLCoRequiredRxBandwidthThis attribute gives the actual bandwidth (in bits per second)
reserved by this path on each of trunks of its route. This attribute
represents the bandwidth for traffic incoming from the remote end
point. The originating end of the connection determines this valuero Gauge32 .1.3.6.1.4.1.562.36.2.1.119.5.10.1.10 |
mscAal1CesLCoRequiredTrafficTypeThis operational attribute indicates the type of traffic transmitted
over the path. There are eight possible traffic types, and the path can
transmit only one of them. The originating end of the connection
determines the type. These are arbitrary designations for traffic
type. The voice, data and video traffic types are defined, and five
other arbitrary traffic types can be defined by the network
administration. This attribute is used in the route selection process
to restrict the route to trunks that support this traffic type. The
supportedTrafficType trunk attribute lists all the types of traffic
allowed on the trunk. For example, if requiredTrafficType is
specified as trafficType1 then only trunks that include trafficType1
in supportedTrafficType, will be candidates for this connection.ro Enumeration .1.3.6.1.4.1.562.36.2.1.119.5.10.1.11 |
mscAal1CesLCoPermittedTrunkTypesThis operational attribute lists up to eight types of trunk that can be
used on the route. The originating end of the connection determines
the types. The terrestrial and satellite trunk types have been
defined, leaving six remaining arbitrary types that can be defined by
the network administration. The trunk's type is indicated in the
trunkType attribute of the Trunk component. When selecting a
route, PORS only chooses trunks whose trunkType are in the
permittedTrunkTypes for the path.
Description of bits:
terrestrial(0)
satellite(1)
trunkType1(2)
trunkType2(3)
trunkType3(4)
trunkType4(5)
trunkType5(6)
trunkType6(7)ro OCTET STRING .1.3.6.1.4.1.562.36.2.1.119.5.10.1.12 |
mscAal1CesLCoRequiredSecurityThis attribute indicates the required minimum level of security of
the trunks on the route. Zero represents the most secure and seven
represents the least secure. The trunk's security is indicated by the
trunkSecurity attribute of the Trunk component, and has values
identical in range and meaning to the requiredSecurity attribute.
PORS ensures that any route selected does not contain a trunk
whose trunkSecurity attribute is numerically greater than the
requiredSecurity.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.119.5.10.1.13 |
mscAal1CesLCoRequiredCustomerParameterThis attribute indicates the allowed customer defined parameter of
the trunks on the route.The originating end of the connection
determines the customer defined parameter. Its value, a number
from zero to seven, is chosen by a network administration to have a
meaning specific to their network, thus allowing them to customize
the use of their trunks. A complementary trunk attribute,
customerParameter, also has a value from zero to seven. The route
selection process does not consider trunks whose
customerParameter is greater than the requiredCustomerParameter
of the path.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.119.5.10.1.14 |
mscAal1CesLCoEmissionPriorityThis attribute indicates the urgency with which packets on the path
are emitted by the trunks on the route. The originating end of the
connection selects the emissionPriority. EmissionPriority of zero
indicates the highest emission priority, while two indicates the
lowest emission priority. Packets with a higher emissionPriority (or
numerically less) are serviced and sent out before the packets of
lower emissionPriority (or numerically higher).ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.119.5.10.1.15 |
mscAal1CesLCoDiscardPriorityThis attribute indicates the importance of the packets on the
path.The originating end of the connection sets discardPriority. One
is used for paths carrying the most important traffic, and three is
used for paths carrying the least important traffic. Packets with
lower discardPriority(numerically lower) are discarded after
packets with a higher discardPriority(numerically higher).ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.119.5.10.1.16 |
mscAal1CesLCoPathTypeThis attribute indicates whether the path for this PLC was
determined automatically or by static provisioning. Normal
pathTypes are selected automatically by Route Selector.The other
pathTypes are both manual pathTypes where the operator must
specify, through provisioning, a static route termed the manualPath.
A manual pathType connection is nearly identical to a normal path
type connection with the exception that the route is pre-provisioned.
For a manual pathType, bandwidth reservations are respected along
the path exactly as in a normal path. The last type, the forced
pathType, is also a manual path but regardless of the bandwidth
available the route is granted provided the trunks are operational
and there are sufficient Logical Channels (LChs).
The forced pathType could result in over committing the reserved
bandwidth allowed on a trunk. A better way to achieve the effects of
a forced pathType is to use a manual pathType with setupPriority =
0 and holdingPriority = 0. In this manner the path will reserve
correct bandwidth and it will bump other paths if required while not
being bumped itself.ro Enumeration .1.3.6.1.4.1.562.36.2.1.119.5.10.1.17 |
mscAal1CesLCoRetryCountThis attribute is the count of the number of times the path chosen
during route selection could not be instantiated. This count should
be three or below if the network is performing adequately. A high
value indicates that the route selection is often performed using an
out-of-date view of available network bandwidth and/or topology.
This attribute will only increase at the calling end of the connection.
This attribute is reset each time a path reconnects and stops
counting when it reaches its maximum value.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.119.5.10.1.18 |
mscAal1CesLCoPathFailureCountThis attribute is the count of the number of times the path has
successfully connected. It is set to zero the first time the path is up.
If a path fails anytime after connecting this count will be
incremented when the path is up again. Failed route requests do not
count in this statistic. See retryCount above. This attribute stops
counting at its maximum value.ro Unsigned32 .1.3.6.1.4.1.562.36.2.1.119.5.10.1.19 |
mscAal1CesLCoReasonForNoRouteThis attribute is the route selection's reasonForNoRoute and
provides a brief reason for which a route was not selected. The
reasons are essentially self-explanatory. Perhaps two reasons for no
route require some explanation. The reason
unknownRemoteNodeName is issued when the remote node name
is not in the topological database. The reason plcAttributesNotMet
is issued when there is no network connectivity at a level specified
by the PLC attributes. This reason is also issued when there is no
physical connectivity between two end nodes.ro Enumeration .1.3.6.1.4.1.562.36.2.1.119.5.10.1.20 |
mscAal1CesLCoLastTearDownReasonThis attribute reflects the last tear down reason for a connection
(LCo). In many cases this displays the reason for a momentary
service interruption. This attribute applies to the last path failure
only. If a path is no longer up, this may give an indication to the
reason that the path has failed. In many cases an alarm will also be
generated with more specific information. The following is a brief
description of the reasons:
none - This path has no information for the teardown this is typical
of a path provisioned with no remoteName that has not been up.
normalShutDown - This path has gone down due to normal call
termination.
insufficientTxLcOrBandwidth - At present there is either no
available bandwidth or logical channel numbers available on one or
more of the trunks for this path in the transmit direction.
insufficientRxLcOrBandwidth - At present there is either no
available bandwidth or logical channel numbers available on one or
more of the trunks for this path in the receive direction.
trunkFailure- A trunk on the path has failed or has gone down due
to a provisioning change of a critical attribute.
trunkCardFailure- A trunk FP card has failed along the path.
accessCardFailure- The FP on which the peer access service was
running has failed.
operatorForced- The path has terminated due to the operator
locking a trunk along the path.
lostLcnClash- The path has terminated because the PA's at both
ends of an intermediate trunk have allocated the same LC to
different calls. When this happens both calls must go down and then
try to come up again a fraction of a second later (effectively
ensuring that they will now be assigned different LC's). It is normal
to get the odd clash especially when the PA's usedLC is
approaching the PA's maxLC.
networkCongestion - The path has failed due to control information
being lost and not recoverable.
trunkNotFound - Occurs on a manual path usually. Check for
trunks not up or names provisioned incorrectly.
farEndNotFound - The far end is not provisioned or is not up.
Check remote Name.
wrongModuleReached - This may occur on a manual path. Check
provisioning for correct trunk and service names. For a normal
path, the network Topology may be changing check remoteName.
farEndBusy - The far end has been reached but it is busy. Check
remoteName and remote end provisioning.
callLoopedBack - This LCo is provisioned to call itself. Re-
provision since this is invalid.
unknownReason - The failure was not resolved.
farEndNotReady - The remote end was reached but the connection
was refused due to the remote end not being enabled.
remoteNameMismatch - The remote end has alarmed and rejected
this setup due to remoteName provisioning.
serviceTypeMismatch - The remote Service Type does not match
this service type. Check provisioning.
reconnectFromFarEnd - The remote end re-established this
connection. Check the remote end lastTearDownReason to
determine the real reason.
bumped - Another call bumped this path from a trunk to get
bandwidth (or an LC) which it required to come up. This other path
had a higher setupPriority than this path's holdingPriority hence it
was allowed to steal the bandwidth (or LC) from this path.
optimized - This call has been rerouted due to the optimization
feature. The call is still active this just indicates why the path
changed.
trunkOrFarEndDidNotSupportMode - This call was unable to
complete because a mode required by the service was not supported
by one of the trunks the route went through or by the far end service
it connected to. Currently the only mode that this applies to is the
map/mux mode on TRUNK PA ATM component. Map mode was
required by the application (CES/FrAtm etc.) but was not available
on the TRUNK PA ATM component through which the call was
routed or the far end CES/FrAtm component did not specify the
same mode.ro Enumeration .1.3.6.1.4.1.562.36.2.1.119.5.10.1.21 |
mscAal1CesLCoPathFailureActionThis attribute displays whether the application is set to tolerate
momentary interruption of a path while a new path is selected. If
disconnectConnection is displayed, the application is informed as
soon as possible about a failure by disconnection. If the attribute
displays reRoutePath, the path may attempt an immediate reroute,
provided the failure is a recoverable failure. If rerouting fails the
application is informed of the failure.
With this option set to reRoutePath the LCo may wait up to 30
seconds before informing the service of complete disconnection in
order to allow both ends to attempt to reconnect. Note that if PLC
components are different at both ends only the calling end is
allowed to reconnect.
All pathTypes respect this attribute. Also on a manualPath with
both ends provisioned with independent paths (at least with respect
to the failure) this option will have the desired effect that the path is
rerouted without complete disconnection at both endsro Enumeration .1.3.6.1.4.1.562.36.2.1.119.5.10.1.22 |
mscAal1CesLCoBumpPreferenceThis attribute specifies when bumping will occur during route
selection process. Bumping may occur when necessary or always. It
will be necessary for a connection to bump if there is not enough
resources for the connection to be established and these resources
are occupied by a connection whose setupPriority is lower
(numerically higher) than the connection's setupPriority. A
connection may also always bump in order to obtain the best route.ro Enumeration .1.3.6.1.4.1.562.36.2.1.119.5.10.1.23 |
mscAal1CesLCoOptimizationThis attribute is used to specify whether this connection should
attempt to optimize its path when requested by the routing PORS
component. Every path is as optimal as it can be when it is
established, but as network traffic patterns and configurations
change this path may no longer be as optimal as it could be. The
PORS connection manager on a module requests circuits to
optimize at the optimization interval.ro Enumeration .1.3.6.1.4.1.562.36.2.1.119.5.10.1.24 |
mscAal1CesLCoPathUpDateTimeThis is the time stamp when the current path was established or
reestablished.ro EnterpriseDateAndTime .1.3.6.1.4.1.562.36.2.1.119.5.10.1.25 |
mscAal1CesLCoStatsTableThis group contains the operational statistics attributes for the path
oriented LCo. SEQUENCE OF MscAal1CesLCoStatsEntry .1.3.6.1.4.1.562.36.2.1.119.5.11 |
mscAal1CesLCoStatsEntryAn entry in the mscAal1CesLCoStatsTable. MscAal1CesLCoStatsEntry .1.3.6.1.4.1.562.36.2.1.119.5.11.1 |
mscAal1CesLCoPktsToNetworkThis attribute counts the number of packets transmitted to the
network over this Logical Connection.ro PassportCounter64 .1.3.6.1.4.1.562.36.2.1.119.5.11.1.1 |
mscAal1CesLCoBytesToNetworkThis attribute counts the number of bytes sent to the network over
this Logical Connection.ro PassportCounter64 .1.3.6.1.4.1.562.36.2.1.119.5.11.1.2 |
mscAal1CesLCoPktsFromNetworkThis attribute counts the number of packets received from the
remote LCo via the network.ro PassportCounter64 .1.3.6.1.4.1.562.36.2.1.119.5.11.1.3 |
mscAal1CesLCoBytesFromNetworkThis attribute counts the number of bytes received from the remote
LCo via the network.ro PassportCounter64 .1.3.6.1.4.1.562.36.2.1.119.5.11.1.4 |
mscAal1CesLCoPathTableThis attribute contains the trunk component names over which the
path has been instantiated and the remote end point name
terminating the path. SEQUENCE OF MscAal1CesLCoPathEntry .1.3.6.1.4.1.562.36.2.1.119.5.264 |
mscAal1CesLCoPathEntryAn entry in the mscAal1CesLCoPathTable. MscAal1CesLCoPathEntry .1.3.6.1.4.1.562.36.2.1.119.5.264.1 |
mscAal1CesLCoPathValueThis variable represents both the value and the index for the
mscAal1CesLCoPathTable.ro AsciiString .1.3.6.1.4.1.562.36.2.1.119.5.264.1.1 |
mscAal1CesAtmCon OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.1.119.6 |
mscAal1CesAtmConRowStatusTableThis entry controls the addition and deletion of
mscAal1CesAtmCon components. SEQUENCE OF MscAal1CesAtmConRowStatusEntry .1.3.6.1.4.1.562.36.2.1.119.6.1 |
mscAal1CesAtmConRowStatusEntryA single entry in the table represents a single
mscAal1CesAtmCon component. MscAal1CesAtmConRowStatusEntry .1.3.6.1.4.1.562.36.2.1.119.6.1.1 |
mscAal1CesAtmConRowStatusThis variable is used as the basis for SNMP naming of
mscAal1CesAtmCon components.
These components cannot be added nor deleted.ro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.119.6.1.1.1 |
mscAal1CesAtmConComponentNameThis variable provides the component's string name for
use with the ASCII Console Interfacero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.119.6.1.1.2 |
mscAal1CesAtmConStorageTypeThis variable represents the storage type value for the
mscAal1CesAtmCon tables.ro StorageType (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.119.6.1.1.4 |
mscAal1CesAtmConIndexThis variable represents the index for the mscAal1CesAtmCon tables. NonReplicated .1.3.6.1.4.1.562.36.2.1.119.6.1.1.10 |
mscAal1CesAtmConOperTableThis attribute group contains the operational attributes for the
NapAtmConnection component. SEQUENCE OF MscAal1CesAtmConOperEntry .1.3.6.1.4.1.562.36.2.1.119.6.10 |
mscAal1CesAtmConOperEntryAn entry in the mscAal1CesAtmConOperTable. MscAal1CesAtmConOperEntry .1.3.6.1.4.1.562.36.2.1.119.6.10.1 |
mscAal1CesAtmConNextHopThis attribute shows the component name of the AtmIf Vcc Ep or
AtmCon component to which this switched connection is
established.ro RowPointer .1.3.6.1.4.1.562.36.2.1.119.6.10.1.1 |
mscAal1CesCidDataTableThis group contains the attribute for a component's Customer
Identifier (CID). Refer to the attribute description for a detailed
explanation of CIDs. SEQUENCE OF MscAal1CesCidDataEntry .1.3.6.1.4.1.562.36.2.1.119.10 |
mscAal1CesCidDataEntryAn entry in the mscAal1CesCidDataTable. MscAal1CesCidDataEntry .1.3.6.1.4.1.562.36.2.1.119.10.1 |
mscAal1CesCustomerIdentifierThis attribute holds the Customer Identifier (CID).
Every component has a CID. If a component has a cid attribute, the
component's CID is the provisioned value of that attribute;
otherwise the component inherits the CID of its parent. The top-
level component has a CID of 0.
Every operator session also has a CID, which is the CID
provisioned for the operator's user ID. An operator will see only the
stream data for components having a matching CID. Also, the
operator will be allowed to issue commands for only those
components which have a matching CID.
An operator CID of 0 is used to identify the Network Manager
(referred to as 'NetMan' in DPN). This CID matches the CID of
any component. Values 1 to 8191 inclusive (equivalent to 'basic
CIDs' in DPN) may be assigned to specific customers.rw Unsigned32 (0 | 1..8191) .1.3.6.1.4.1.562.36.2.1.119.10.1.1 |
mscAal1CesProvTableThis group contains basic provisioning data for the AAL1 Circuit
Emulation Service. SEQUENCE OF MscAal1CesProvEntry .1.3.6.1.4.1.562.36.2.1.119.11 |
mscAal1CesProvEntryAn entry in the mscAal1CesProvTable. MscAal1CesProvEntry .1.3.6.1.4.1.562.36.2.1.119.11.1 |
mscAal1CesServiceTypeThis attribute specifies the service type for the CES.
In an unstructured service, the entire data stream at the service
interface (including any framing bits which may be present) is
passed across the network transparently.
The unstructured service uses the Unstructured Data Transfer
(UDT) mode of AAL1.
In a structured service, an Nx64kbit/s fraction of the data stream at
the service interface is passed across the network. Two modes of
structured service are supported: basicStructured and casStructured.
In a casStructured service, the Channel Associated Signalling
(CAS) bits are carried in a separate data structure from the Nx64
payload; in a basicStructured service they are not.
The structured service uses the Structured Data Transfer (SDT)
mode as defined in ITU-T Recommendation I.363.1.
The serviceType attributes at both ends of a connection must be the
same.rw Enumeration .1.3.6.1.4.1.562.36.2.1.119.11.1.1 |
mscAal1CesBufferSizeOn 4pDS1Aal1 and 4pE1Aal1 cards, this attribute specifies the size
of the AAL1 receive segment reassembly buffer in bytes. On
initialization the buffer is filled to a level determined by
cellDelayVariationTolerance. Thereafter the buffer is emptied as
TDM frames are transmitted, and is filled as ATM cells are
received. If the buffer overflows, sufficient data is discarded to bring
the level down to that set after initialization. The cause of a buffer
overflow may be one or a combination of any of the following: cell-
arrival-jitter, initialization with delayed ATM cells, or TDM clock
difference or wander.
On 4pDS1Aal1 and 4pE1Aal1 cards, if this attribute is
autoConfigure, the buffer size applied is equivalent to two times
cellDelayVariationTolerance. A provisioned numeric value of
bufferSize must be higher than the equivalent
cellDelayVariationTolerance, plus an allowance of one ATM Cell
for the quantization of data in cells, and an allowance, if applicable,
for the ATM overheads of structured CES.
On MSA cards this attribute's value must be autoConfigure, to
acknowledge that maximumBufferDelay is provisioned instead of
this attribute.
Setting this attribute too low allows traffic with normal CDV to
cause unnecessary loss of data on the service interface. Setting this
attribute too high permits the buffer to introduce an unnecessarily
high propagation delay.
VALUES (
0 = autoConfigure
)rw Unsigned32 (0 | 94..15651) .1.3.6.1.4.1.562.36.2.1.119.11.1.2 |
mscAal1CesCellLossIntegrationPeriodThis attribute specifies the cell loss integration period. This period
defines the interval of time (in milliseconds) for which a loss of
cells condition must persist before a buffer underflow alarm is
raised. A loss of cells condition occurs when the flow of cells to the
AAL1 reassembly buffer stops, causing a buffer underflow or
starvation condition.
The operational attribute cellLossStatus will be set to loss when the
buffer underflow alarm is raised, and noLoss when it is cleared.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.119.11.1.4 |
mscAal1CesInterfaceNameThis attribute identifies the instance of Chan to which an instance of
Aal1Ces is linked.rw Link .1.3.6.1.4.1.562.36.2.1.119.11.1.5 |
mscAal1CesPartialFillA significant source of delay in a structured service is the amount of
time it takes to collect enough data to fill a cell. This period of time
can be reduced by sending cells that are only partially filled with
data (idlePattern octets are added to the ATM payload beyond the
partial fill level).
This attribute specifies the number of payload octets to fill with
data. It is applicable to structured services only, and must be set to
47 for unstructured services.
On a given AAL1 Function Processor, the maximum cell rate that
can be sustained is dependent upon the combined bandwidths of the
provisioned services, and (for structured services) the levels of
partialFill. The smaller the partialFill level, the greater the cell rate
and hence the fewer the services that can be sustained at that fill
level.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.119.11.1.6 |
mscAal1CesIdleSuppressionThis attribute controls the suppression of idle cells. An idle cell is
one in which the bytes of the ATM payload (up to the partialFill
level) match the idlePattern.
If idleSuppression is off, idle cells are not suppressed.
If idleSuppression is on, at least 75% of cells are suppressed under
idle conditions.
The strategy is as follows: the first idle cell after a sequence of non-
idle cells is always sent; those that follow are suppressed. Note,
however, that at least one cell in eight is always sent (to allow the
receive end to regenerate the suppressed cells) and more often than
not, two cells are sent (the cell containing the AAL1 pointer, which
will almost always fail to match, and the one after that).rw Enumeration .1.3.6.1.4.1.562.36.2.1.119.11.1.7 |
mscAal1CesIdlePatternThis attribute specifies the pattern which the bytes of an ATM
payload, up to the partialFill level, must match in order for the cell
to be classified as idle. Payload bytes beyond the partialFill level
are not checked.
The suppression of idle cells is controlled by the attribute
idleSuppression. If idleSuppression is on, at least 75% of cells are
suppressed under idle conditions.rw Hex .1.3.6.1.4.1.562.36.2.1.119.11.1.8 |
mscAal1CesCellLossRecoveryPeriodThis attribute specifies the cell loss recovery period. This period
defines the interval of time (in seconds) for which a loss of cells
condition must desist before the buffer underflow alarm is cleared.
The operational attribute cellLossStatus will be set to noLoss when
the buffer underflow alarm is cleared.rw Unsigned32 .1.3.6.1.4.1.562.36.2.1.119.11.1.9 |
mscAal1CesDummyDataByteThis attribute specifies the pattern which is played out onto the
service interface to maintain bit integrity when data is unavailable
from the ATM network.
For an unstructured service (serviceType is set to unstructured),
dummyDataByte must be set to FF.rw Hex .1.3.6.1.4.1.562.36.2.1.119.11.1.10 |
mscAal1CesMaximumBufferDelayThis attribute specifies the maximum delay that a Cell Delay
Variation buffer is permitted to add to the egress stream. The delay
in the buffer is modified in response to variation in the egress cell
stream. At the point that the delay would be modified in excess of
the maximum, sufficient data is discarded that the delay returns to
cellDelayVariationTolerance.
Setting this attribute too low allows traffic with normal CDV to
cause unnecessary loss of data on the service interface. Setting this
attribute too high permits the buffer to introduce an unnecessarily
high propagation delay.
If this attribute is autoConfigure, the maximum delay tolerated in
the buffer is two times cellDelayVariationTolerance. On MSA
cards, 'best-effort' applies on a channel with high
cellDelayVariationTolerance and low ATM bandwidth. The value
applied is the same as the range limit on provisioned
maximumBufferDelay on that channel.
On MSA cards this attribute's value is rounded up to the nearest
multiple of 0.125ms when applied to the buffer. The range is
nominally 0.12..63.62ms, but the upper limit may be reduced by up
to 6ms one a channel with high cellDelayVariationTolerance and
low ATM bandwidth.
On 4pDS1Aal1 and 4pE1Aal1 cards this attribute's value is rounded
up to the nearest multiple of 1ms when applied to the buffer. The
upper limit is roughly inverse- proportional to the ATM bandwidth
of the channel.
VALUES (
0 = autoConfigure
)rw FixedPoint2 (0 | 1..65500) .1.3.6.1.4.1.562.36.2.1.119.11.1.11 |
mscAal1CesDp2CellDelayVariationToleranceThis attribute specifies the maximum time that a cell may arrive
late, compared to a nominal time established at buffer initialization,
without producing errors on the service interface. The nominal time
of a cell's arrival is predicted according to the time interval required
to transmit a cell's worth of data on the service interface.
This attribute's value is the delay that the Cell Delay Variation
Tolerance buffer adds to the egress stream immediately after the
buffer initializes. The buffer absorbs variation in the arrival time of
cells from the network, so that a steady stream of data appears on
the service interface. If the buffer underflows, due to a late cell, fill-
in data is output on the service interface while the buffer re-
initializes. When the buffer has re-initialized, normal data is output
on the service interface and the delay in the buffer is restored to the
value of this attribute.
This attribute must have a value lower than a numeric value of
maximumBufferDelay. The relationship between this attribute and
bufferSize is described under that attribute.
Setting this attribute too low allows traffic with normal CDV to
cause unnecessary loss of data on the service interface. Setting this
attribute too high imposes an unnecessarily high propagation delay
on the egress stream.
On MSA cards this attribute's provisionable range is 0.01..32ms and
the value applied is rounded up to the nearest multiple of 0.125ms.
On 4pDS1Aal1 and 4pE1Aal1 cards, this attribute's provisionable
range is strongly dependent on the bandwidth of the channel, and
the value applied is rounded up to the nearest whole number of
milliseconds, then rounded down to the equivalent number of cells.rw FixedPoint2 .1.3.6.1.4.1.562.36.2.1.119.11.1.12 |
mscAal1CesStateTableThis group contains the three OSI State attributes and the six OSI
Status attributes. The descriptions generically indicate what each
attribute implies about the component. Note that not all the values
and state combinations described here are supported by every
component which uses this group. For component-specific
information and the valid state combinations, refer to NTP 241-
7001-150, Passport Operations and Maintenance Guide. SEQUENCE OF MscAal1CesStateEntry .1.3.6.1.4.1.562.36.2.1.119.12 |
mscAal1CesStateEntryAn entry in the mscAal1CesStateTable. MscAal1CesStateEntry .1.3.6.1.4.1.562.36.2.1.119.12.1 |
mscAal1CesAdminStateThis attribute indicates the OSI Administrative State of the
component.
The value locked indicates that the component is administratively
prohibited from providing services for its users. A Lock or Lock -
force command has been previously issued for this component.
When the value is locked, the value of usageState must be idle.
The value shuttingDown indicates that the component is
administratively permitted to provide service to its existing users
only. A Lock command was issued against the component and it is
in the process of shutting down.
The value unlocked indicates that the component is administratively
permitted to provide services for its users. To enter this state, issue
an Unlock command to this component.
The OSI Status attributes, if supported by the component, may
provide more details, qualifying the state of the component.ro Enumeration .1.3.6.1.4.1.562.36.2.1.119.12.1.1 |
mscAal1CesOperationalStateThis attribute indicates the OSI Operational State of the component.
The value enabled indicates that the component is available for
operation. Note that if adminState is locked, it would still not be
providing service.
The value disabled indicates that the component is not available for
operation. For example, something is wrong with the component
itself, or with another component on which this one depends. If the
value is disabled, the usageState must be idle.
The OSI Status attributes, if supported by the component, may
provide more details, qualifying the state of the component.ro Enumeration .1.3.6.1.4.1.562.36.2.1.119.12.1.2 |
mscAal1CesUsageStateThis attribute indicates the OSI Usage State of the component.
The value idle indicates that the component is not currently in use.
The value active indicates that the component is in use and has
spare capacity to provide for additional users.
The value busy indicates that the component is in use and has no
spare operating capacity for additional users at this time.
The OSI Status attributes, if supported by the component, may
provide more details, qualifying the state of the component.ro Enumeration .1.3.6.1.4.1.562.36.2.1.119.12.1.3 |
mscAal1CesAvailabilityStatusIf supported by the component, this attribute indicates the OSI
Availability status of the component. Note that, even though it is
defined as a multi-valued set, at most one value is shown to the user.
When no values are in the set, this indicates that either the attribute
is not supported or that none of the status conditions described
below are present.
The value inTest indicates that the resource is undergoing a test
procedure. If adminState is locked or shuttingDown, the normal
users are precluded from using the resource and controlStatus is
reservedForTest. Tests that do not exclude additional users can be
present in any operational or administrative state but the
reservedForTest condition should not be present.
The value failed indicates that the component has an internal fault
that prevents it from operating. The operationalState is disabled.
The value dependency indicates that the component cannot operate
because some other resource on which it depends is unavailable.
The operationalState is disabled.
The value powerOff indicates the resource requires power to be
applied and it is not powered on. The operationalState is disabled.
The value offLine indicates the resource requires a routine
operation (either manual, automatic, or both) to be performed to
place it on-line and make it available for use. The operationalState
is disabled.
The value offDuty indicates the resource is inactive in accordance
with a predetermined time schedule. In the absence of other
disabling conditions, the operationalState is enabled or disabled.
The value degraded indicates the service provided by the
component is degraded in some way, such as in speed or operating
capacity. However, the resource remains available for service. The
operationalState is enabled.
The value notInstalled indicates the resource is not present. The
operationalState is disabled.
The value logFull is not used.
Description of bits:
inTest(0)
failed(1)
powerOff(2)
offLine(3)
offDuty(4)
dependency(5)
degraded(6)
notInstalled(7)
logFull(8)ro OCTET STRING .1.3.6.1.4.1.562.36.2.1.119.12.1.4 |
mscAal1CesProceduralStatusIf supported by the component, this attribute indicates the OSI
Procedural status of the component. Note that, even though it is
defined as a multi-valued set, at most one value is shown to the user.
When no values are in the set, this indicates that either the attribute
is not supported or that none of the status conditions described
below are present.
The value initializationRequired indicates (for a resource which
doesn't initialize autonomously) that initialization is required before
it can perform its normal functions, and this procedure has not been
initiated. The operationalState is disabled.
The value notInitialized indicates (for a resource which does
initialize autonomously) that initialization is required before it can
perform its normal functions, and this procedure has not been
initiated. The operationalState may be enabled or disabled.
The value initializing indicates that initialization has been initiated
but is not yet complete. The operationalState may be enabled or
disabled.
The value reporting indicates the resource has completed some
processing operation and is notifying the results. The
operationalState is enabled.
The value terminating indicates the component is in a termination
phase. If the resource doesn't reinitialize autonomously,
operationalState is disabled; otherwise it is enabled or disabled.
Description of bits:
initializationRequired(0)
notInitialized(1)
initializing(2)
reporting(3)
terminating(4)ro OCTET STRING .1.3.6.1.4.1.562.36.2.1.119.12.1.5 |
mscAal1CesControlStatusIf supported by the component, this attribute indicates the OSI
Control status of the component. Note that, even though it is defined
as a multi-valued set, at most one value is shown to the user.
When no values are in the set, this indicates that either the attribute
is not supported or that none of the status conditions described
below are present.
The value subjectToTest indicates the resource is available but tests
may be conducted simultaneously at unpredictable times, which
may cause it to exhibit unusual characteristics.
The value partOfServicesLocked indicates that part of the service is
restricted from users of a resource. The adminState is unlocked.
The value reservedForTest indicates that the component is
administratively unavailable because it is undergoing a test
procedure. The adminState is locked.
The value suspended indicates that the service has been
administratively suspended.
Description of bits:
subjectToTest(0)
partOfServicesLocked(1)
reservedForTest(2)
suspended(3)ro OCTET STRING .1.3.6.1.4.1.562.36.2.1.119.12.1.6 |
mscAal1CesAlarmStatusIf supported by the component, this attribute indicates the OSI
Alarm status of the component. Note that, even though it is defined
as a multi-valued set, at most one value is shown to the user.
When no values are in the set, this indicates that either the attribute
is not supported or that none of the status conditions described
below are present.
The value underRepair indicates the component is currently being
repaired. The operationalState is enabled or disabled.
The value critical indicates one or more critical alarms are
outstanding against the component. Other, less severe, alarms may
also be outstanding. The operationalState is enabled or disabled.
The value major indicates one or more major alarms are
outstanding against the component. Other, less severe, alarms may
also be outstanding. The operationalState is enabled or disabled.
The value minor indicates one or more minor alarms are
outstanding against the component. Other, less severe, alarms may
also be outstanding. The operationalState is enabled or disabled.
The value alarmOutstanding generically indicates that an alarm of
some severity is outstanding against the component.
Description of bits:
underRepair(0)
critical(1)
major(2)
minor(3)
alarmOutstanding(4)ro OCTET STRING .1.3.6.1.4.1.562.36.2.1.119.12.1.7 |
mscAal1CesStandbyStatusIf supported by the component, this attribute indicates the OSI
Standby status of the component.
The value notSet indicates that either the attribute is not supported
or that none of the status conditions described below are present.
Note that this is a non-standard value, used because the original
specification indicated this attribute was set-valued and thus, did not
provide a value to indicate that none of the other three are
applicable.
The value hotStandby indicates that the resource is not providing
service but will be immediately able to take over the role of the
resource to be backed up, without initialization activity, and
containing the same information as the resource to be backed up.
The value coldStandby indicates the resource is a backup for
another resource but will not be immediately able to take over the
role of the backed up resource and will require some initialization
activity.
The value providingService indicates that this component, as a
backup resource, is currently backing up another resource.ro Enumeration .1.3.6.1.4.1.562.36.2.1.119.12.1.8 |
mscAal1CesUnknownStatusThis attribute indicates the OSI Unknown status of the component.
The value false indicates that all of the other OSI State and Status
attribute values can be considered accurate.
The value true indicates that the actual state of the component is not
known for sure.ro Enumeration .1.3.6.1.4.1.562.36.2.1.119.12.1.9 |
mscAal1CesOperTableThis group contains status information about the AAL1 Circuit
Emulation Service. SEQUENCE OF MscAal1CesOperEntry .1.3.6.1.4.1.562.36.2.1.119.13 |
mscAal1CesOperEntryAn entry in the mscAal1CesOperTable. MscAal1CesOperEntry .1.3.6.1.4.1.562.36.2.1.119.13.1 |
mscAal1CesCellLossStatusThis attribute is set to loss when a buffer underflow alarm is raised
(see cellLossIntegrationPeriod), and noLoss when it is clear.ro Enumeration .1.3.6.1.4.1.562.36.2.1.119.13.1.1 |
mscAal1CesAal1LayerLossStatusThis attribute is set to loss when an AAL1 layer alarm is raised, and
noLoss when it is clear.ro Enumeration .1.3.6.1.4.1.562.36.2.1.119.13.1.2 |
mscAal1CesConnectionStatusThis attribute indicates whether a service is non-operational because
of a problem with the service interface side of the service (in which
case, it is set to channelNotReady) or because of a problem with the
ATM side of the service (in which case, it is set to
atmNotConfigured or atmNotReady).
When this attribute is set to channelNotReady, it is an indication
that the corresponding Chan component (as defined by the attribute
interfaceName) or the Chan component's parent port component
(Lp/n Ds1/m or Lp/n E1/m) is locked.
When this attribute is set to atmNotConfigured, it is an indication
that no sub-component has been provisioned, and thus no ATM
connection has been configured for the service.
When this attribute is set to atmNotReady, it is an indication that the
ATM connection with which the service is associated (as defined by
a sub-component) has been lost or that it is currently unable to carry
CES data.
This attribute is set to connected when a service is operational (that
is, the OSI attribute operationalState is enabled.)ro Enumeration .1.3.6.1.4.1.562.36.2.1.119.13.1.3 |
mscAal1CesStatsTableThis group contains statistical data for an AAL1 Circuit Emulation
Service. SEQUENCE OF MscAal1CesStatsEntry .1.3.6.1.4.1.562.36.2.1.119.14 |
mscAal1CesStatsEntryAn entry in the mscAal1CesStatsTable. MscAal1CesStatsEntry .1.3.6.1.4.1.562.36.2.1.119.14.1 |
mscAal1CesCellsTransmittedThis attribute counts the total number of cells transmitted to the
backplane (ingress direction). This includes cells containing CBR
data, trunk conditioning cells (structured services), and unframed
AIS cells (unstructured services).
The counter wraps when the maximum value is exceeded.ro PassportCounter64 .1.3.6.1.4.1.562.36.2.1.119.14.1.1 |
mscAal1CesCellsReceivedThis attribute counts the total number of cells received from the
backplane (egress direction). This includes CBR user data cells,
cells with AAL1 header errors (correctable and non-correctable)
and cells with AAL1 sequencing errors. The counter wraps when
the maximum value is exceeded.ro PassportCounter64 .1.3.6.1.4.1.562.36.2.1.119.14.1.2 |
mscAal1CesLostCellsThis attribute counts the number of cells declared as never received
by the AAL1 protocol layer. The counter wraps when the maximum
value is exceeded.ro Counter32 .1.3.6.1.4.1.562.36.2.1.119.14.1.3 |
mscAal1CesBufferUnderflowsThis attribute counts the number of times the AAL1 reassembly
buffer underflows. In the case of a continuous buffer starvation, a
single buffer underflow event will be counted. The counter wraps
when the maximum value is exceeded.ro Counter32 .1.3.6.1.4.1.562.36.2.1.119.14.1.4 |
mscAal1CesBufferOverflowsThis attribute counts the number of times the AAL1 reassembly
buffer overflows. Buffer overflows occur when AAL1 cells arrive at
a rate above that which is expected. Occurrences of this condition
may be reduced by increasing the value of the attribute bufferSize or
maximumBufferDelay. The buffer overflow counter wraps when the
maximum value is exceeded.ro Counter32 .1.3.6.1.4.1.562.36.2.1.119.14.1.5 |
mscAal1CesReassembledCellsThis attribute counts the number of received cells whose payload
has been played out to the service interface. The counter wraps
when the maximum value is exceeded.ro PassportCounter64 .1.3.6.1.4.1.562.36.2.1.119.14.1.6 |
mscAal1CesHeaderErrorsThis attribute counts the number of cells received with AAL1
header errors. The counter wraps when the maximum value is
exceeded.ro Counter32 .1.3.6.1.4.1.562.36.2.1.119.14.1.7 |
mscAal1CesPointerReframesThis attribute counts the number of times that the AAL1 reassembly
unit found an SDT pointer where it was not expected to be, and as a
result had to reacquire it. Errors of this kind can occur because of
problems at the far end.
This attribute is meaningful for structured services only, and will be
0 for unstructured services.
This counter wraps when the maximum value is exceeded.ro Counter32 .1.3.6.1.4.1.562.36.2.1.119.14.1.8 |
mscAal1CesPointerParityErrorsThis attribute counts the number of times that the AAL1 reassembly
unit detects a parity check failure at the point where an SDT pointer
is expected. Errors of this kind can occur because of problems at the
far end.
This attribute is meaningful for structured services only, and will be
0 for unstructured services.
This counter wraps when the maximum value is exceeded.ro Counter32 .1.3.6.1.4.1.562.36.2.1.119.14.1.9 |
mscAal1CesAal1SequenceErrorsThis attribute counts the number of times that the sequence number
of an incoming AAL1 Type 1 SAR-PDU gets out of
synchronisation, as defined by ITU-T Recommendation I.363.1.
This counter wraps when the maximum value is exceeded.ro Counter32 .1.3.6.1.4.1.562.36.2.1.119.14.1.10 |
mscAal1CesMisinsertedCellsThis attribute counts the number of AAL1 sequence violations
which the AAL convergence sublayer interprets as misinserted
cells, as defined by ITU-T I.363.1.
This counter wraps when the maximum value is exceeded.ro Counter32 .1.3.6.1.4.1.562.36.2.1.119.14.1.11 |
mscMmTx OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.1.151 |
mscMmTxRowStatusTableThis entry controls the addition and deletion of
mscMmTx components. SEQUENCE OF MscMmTxRowStatusEntry .1.3.6.1.4.1.562.36.2.1.151.1 |
mscMmTxRowStatusEntryA single entry in the table represents a single
mscMmTx component. MscMmTxRowStatusEntry .1.3.6.1.4.1.562.36.2.1.151.1.1 |
mscMmTxRowStatusThis variable is used as the basis for SNMP naming of
mscMmTx components.
These components can be added and deleted.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.151.1.1.1 |
mscMmTxComponentNameThis variable provides the component's string name for
use with the ASCII Console Interfacero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.151.1.1.2 |
mscMmTxStorageTypeThis variable represents the storage type value for the
mscMmTx tables.ro StorageType (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.151.1.1.4 |
mscMmTxIndexThis variable represents the index for the mscMmTx tables. Integer32 .1.3.6.1.4.1.562.36.2.1.151.1.1.10 |
mscMmTxNap OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.1.151.2 |
mscMmTxNapRowStatusTableThis entry controls the addition and deletion of
mscMmTxNap components. SEQUENCE OF MscMmTxNapRowStatusEntry .1.3.6.1.4.1.562.36.2.1.151.2.1 |
mscMmTxNapRowStatusEntryA single entry in the table represents a single
mscMmTxNap component. MscMmTxNapRowStatusEntry .1.3.6.1.4.1.562.36.2.1.151.2.1.1 |
mscMmTxNapRowStatusThis variable is used as the basis for SNMP naming of
mscMmTxNap components.
These components can be added and deleted.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.151.2.1.1.1 |
mscMmTxNapComponentNameThis variable provides the component's string name for
use with the ASCII Console Interfacero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.151.2.1.1.2 |
mscMmTxNapStorageTypeThis variable represents the storage type value for the
mscMmTxNap tables.ro StorageType (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.151.2.1.1.4 |
mscMmTxNapIndexThis variable represents the index for the mscMmTxNap tables. NonReplicated .1.3.6.1.4.1.562.36.2.1.151.2.1.1.10 |
mscMmTxNapProvTableThis group contains the provisioning data for the
NailedUpAdaptationPoint component. SEQUENCE OF MscMmTxNapProvEntry .1.3.6.1.4.1.562.36.2.1.151.2.10 |
mscMmTxNapProvEntryAn entry in the mscMmTxNapProvTable. MscMmTxNapProvEntry .1.3.6.1.4.1.562.36.2.1.151.2.10.1 |
mscMmTxNapAtmConnectionThis attribute specifies the identity of the component to which the
NailedUpAdaptationPoint is linked. This is an AtmIf Vcc
NailedUpEndPoint or an AtmIf Vpt Vcc NailedUpEndPoint (the
AAL1 cells are transported off the switch over an ATM UNI, where
they are routed to the appropriate AAL1 entity at the other end by
the ATM bearer service).rw Link .1.3.6.1.4.1.562.36.2.1.151.2.10.1.1 |
mscMmTxAtmCon OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.1.151.6 |
mscMmTxAtmConRowStatusTableThis entry controls the addition and deletion of
mscMmTxAtmCon components. SEQUENCE OF MscMmTxAtmConRowStatusEntry .1.3.6.1.4.1.562.36.2.1.151.6.1 |
mscMmTxAtmConRowStatusEntryA single entry in the table represents a single
mscMmTxAtmCon component. MscMmTxAtmConRowStatusEntry .1.3.6.1.4.1.562.36.2.1.151.6.1.1 |
mscMmTxAtmConRowStatusThis variable is used as the basis for SNMP naming of
mscMmTxAtmCon components.
These components cannot be added nor deleted.ro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.151.6.1.1.1 |
mscMmTxAtmConComponentNameThis variable provides the component's string name for
use with the ASCII Console Interfacero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.151.6.1.1.2 |
mscMmTxAtmConStorageTypeThis variable represents the storage type value for the
mscMmTxAtmCon tables.ro StorageType (SNMPv2-TC) .1.3.6.1.4.1.562.36.2.1.151.6.1.1.4 |
mscMmTxAtmConIndexThis variable represents the index for the mscMmTxAtmCon tables. NonReplicated .1.3.6.1.4.1.562.36.2.1.151.6.1.1.10 |
mscMmTxAtmConOperTableThis attribute group contains the operational attributes for the
NapAtmConnection component. SEQUENCE OF MscMmTxAtmConOperEntry .1.3.6.1.4.1.562.36.2.1.151.6.10 |
mscMmTxAtmConOperEntryAn entry in the mscMmTxAtmConOperTable. MscMmTxAtmConOperEntry .1.3.6.1.4.1.562.36.2.1.151.6.10.1 |
mscMmTxAtmConNextHopThis attribute shows the component name of the AtmIf Vcc Ep or
AtmCon component to which this switched connection is
established.ro RowPointer .1.3.6.1.4.1.562.36.2.1.151.6.10.1.1 |
mscMmTxCidDataTableThis group contains the attribute for a component's Customer
Identifier (CID). Refer to the attribute description for a detailed
explanation of CIDs. SEQUENCE OF MscMmTxCidDataEntry .1.3.6.1.4.1.562.36.2.1.151.10 |
mscMmTxCidDataEntryAn entry in the mscMmTxCidDataTable. MscMmTxCidDataEntry .1.3.6.1.4.1.562.36.2.1.151.10.1 |
mscMmTxCustomerIdentifierThis attribute holds the Customer Identifier (CID).
Every component has a CID. If a component has a cid attribute, the
component's CID is the provisioned value of that attribute;
otherwise the component inherits the CID of its parent. The top-
level component has a CID of 0.
Every operator session also has a CID, which is the CID
provisioned for the operator's user ID. An operator will see only the
stream data for components having a matching CID. Also, the
operator will be allowed to issue commands for only those
components which have a matching CID.
An operator CID of 0 is used to identify the Network Manager
(referred to as 'NetMan' in DPN). This CID matches the CID of
any component. Values 1 to 8191 inclusive (equivalent to 'basic
CIDs' in DPN) may be assigned to specific customers.rw Unsigned32 (0 | 1..8191) .1.3.6.1.4.1.562.36.2.1.151.10.1.1 |
mscMmTxProvTableThis group contains basic provisioning data for the Maintenance
Monitor Transmitter (MmTx). A MmTx represents a mono-
directional AAL1 Circuit Emulation Service. AAL1 CES attributes
in this group are essential information to the operator about the
AAL1 CES service that must be matched in the Aal1Ces component
that receives the monitored stream.
The check escape checks that only one instance of a
MaintenanceMonitorTx is linked to any one Lp. SEQUENCE OF MscMmTxProvEntry .1.3.6.1.4.1.562.36.2.1.151.11 |
mscMmTxProvEntryAn entry in the mscMmTxProvTable. MscMmTxProvEntry .1.3.6.1.4.1.562.36.2.1.151.11.1 |
mscMmTxLinkToLogicalProcessorThis attribute specifies the instance of a hardware component to
which an instance of this component is linked. Only Lp
components may be linkedrw Link .1.3.6.1.4.1.562.36.2.1.151.11.1.3 |
mscMmTxMonitoredDirectionmonitoredDirection specifies the direction of the monitored traffic.
The default and only value is ingress.rw Enumeration .1.3.6.1.4.1.562.36.2.1.151.11.1.4 |
mscMmTxServiceTypeserviceType specifies the service type of the CES.
The serviceType attribute in the receiving Aal1Ces component must
have the same value as this attribute.
The default and only value is basicStructured.rw Enumeration .1.3.6.1.4.1.562.36.2.1.151.11.1.5 |
mscMmTxPartialFillpartialFill specifies the number of octets that are carried in an ATM
cell by the AAL1 CES service. A full cell contains 47 octets.
The partialFill attribute in the receiving Aal1Ces component must
have the same value as this attribute.
The default and only value is 47.
DESCRIPTIONrw Unsigned32 (47) .1.3.6.1.4.1.562.36.2.1.151.11.1.6 |
mscMmTxIdleSuppressionidleSuppression controls the suppression of idle cells. An idle cell is
one in which the bytes of the ATM payload (up to the partialFill
level) match the idlePattern.
If idleSuppression is off, idle cells are not suppressed.
If idleSuppression is on, at least 75% of cells are suppressed under
idle conditions.
The idleSuppression attribute in the receiving Aal1Ces component
must have the same value as this attribute
The default and only value is off.rw Enumeration .1.3.6.1.4.1.562.36.2.1.151.11.1.7 |
mscMmTxStateTableThis group contains the three OSI State attributes and the six OSI
Status attributes. The descriptions generically indicate what each
attribute implies about the component. Note that not all the values
and state combinations described here are supported by every
component which uses this group. For component-specific
information and the valid state combinations, refer to NTP 241-
7001-150, Passport Operations and Maintenance Guide. SEQUENCE OF MscMmTxStateEntry .1.3.6.1.4.1.562.36.2.1.151.12 |
mscMmTxStateEntryAn entry in the mscMmTxStateTable. MscMmTxStateEntry .1.3.6.1.4.1.562.36.2.1.151.12.1 |
mscMmTxAdminStateThis attribute indicates the OSI Administrative State of the
component.
The value locked indicates that the component is administratively
prohibited from providing services for its users. A Lock or Lock -
force command has been previously issued for this component.
When the value is locked, the value of usageState must be idle.
The value shuttingDown indicates that the component is
administratively permitted to provide service to its existing users
only. A Lock command was issued against the component and it is
in the process of shutting down.
The value unlocked indicates that the component is administratively
permitted to provide services for its users. To enter this state, issue
an Unlock command to this component.
The OSI Status attributes, if supported by the component, may
provide more details, qualifying the state of the component.ro Enumeration .1.3.6.1.4.1.562.36.2.1.151.12.1.1 |
mscMmTxOperationalStateThis attribute indicates the OSI Operational State of the component.
The value enabled indicates that the component is available for
operation. Note that if adminState is locked, it would still not be
providing service.
The value disabled indicates that the component is not available for
operation. For example, something is wrong with the component
itself, or with another component on which this one depends. If the
value is disabled, the usageState must be idle.
The OSI Status attributes, if supported by the component, may
provide more details, qualifying the state of the component.ro Enumeration .1.3.6.1.4.1.562.36.2.1.151.12.1.2 |
mscMmTxUsageStateThis attribute indicates the OSI Usage State of the component.
The value idle indicates that the component is not currently in use.
The value active indicates that the component is in use and has
spare capacity to provide for additional users.
The value busy indicates that the component is in use and has no
spare operating capacity for additional users at this time.
The OSI Status attributes, if supported by the component, may
provide more details, qualifying the state of the component.ro Enumeration .1.3.6.1.4.1.562.36.2.1.151.12.1.3 |
mscMmTxAvailabilityStatusIf supported by the component, this attribute indicates the OSI
Availability status of the component. Note that, even though it is
defined as a multi-valued set, at most one value is shown to the user.
When no values are in the set, this indicates that either the attribute
is not supported or that none of the status conditions described
below are present.
The value inTest indicates that the resource is undergoing a test
procedure. If adminState is locked or shuttingDown, the normal
users are precluded from using the resource and controlStatus is
reservedForTest. Tests that do not exclude additional users can be
present in any operational or administrative state but the
reservedForTest condition should not be present.
The value failed indicates that the component has an internal fault
that prevents it from operating. The operationalState is disabled.
The value dependency indicates that the component cannot operate
because some other resource on which it depends is unavailable.
The operationalState is disabled.
The value powerOff indicates the resource requires power to be
applied and it is not powered on. The operationalState is disabled.
The value offLine indicates the resource requires a routine
operation (either manual, automatic, or both) to be performed to
place it on-line and make it available for use. The operationalState
is disabled.
The value offDuty indicates the resource is inactive in accordance
with a predetermined time schedule. In the absence of other
disabling conditions, the operationalState is enabled or disabled.
The value degraded indicates the service provided by the
component is degraded in some way, such as in speed or operating
capacity. However, the resource remains available for service. The
operationalState is enabled.
The value notInstalled indicates the resource is not present. The
operationalState is disabled.
The value logFull is not used.
Description of bits:
inTest(0)
failed(1)
powerOff(2)
offLine(3)
offDuty(4)
dependency(5)
degraded(6)
notInstalled(7)
logFull(8)ro OCTET STRING .1.3.6.1.4.1.562.36.2.1.151.12.1.4 |
mscMmTxProceduralStatusIf supported by the component, this attribute indicates the OSI
Procedural status of the component. Note that, even though it is
defined as a multi-valued set, at most one value is shown to the user.
When no values are in the set, this indicates that either the attribute
is not supported or that none of the status conditions described
below are present.
The value initializationRequired indicates (for a resource which
doesn't initialize autonomously) that initialization is required before
it can perform its normal functions, and this procedure has not been
initiated. The operationalState is disabled.
The value notInitialized indicates (for a resource which does
initialize autonomously) that initialization is required before it can
perform its normal functions, and this procedure has not been
initiated. The operationalState may be enabled or disabled.
The value initializing indicates that initialization has been initiated
but is not yet complete. The operationalState may be enabled or
disabled.
The value reporting indicates the resource has completed some
processing operation and is notifying the results. The
operationalState is enabled.
The value terminating indicates the component is in a termination
phase. If the resource doesn't reinitialize autonomously,
operationalState is disabled; otherwise it is enabled or disabled.
Description of bits:
initializationRequired(0)
notInitialized(1)
initializing(2)
reporting(3)
terminating(4)ro OCTET STRING .1.3.6.1.4.1.562.36.2.1.151.12.1.5 |
mscMmTxControlStatusIf supported by the component, this attribute indicates the OSI
Control status of the component. Note that, even though it is defined
as a multi-valued set, at most one value is shown to the user.
When no values are in the set, this indicates that either the attribute
is not supported or that none of the status conditions described
below are present.
The value subjectToTest indicates the resource is available but tests
may be conducted simultaneously at unpredictable times, which
may cause it to exhibit unusual characteristics.
The value partOfServicesLocked indicates that part of the service is
restricted from users of a resource. The adminState is unlocked.
The value reservedForTest indicates that the component is
administratively unavailable because it is undergoing a test
procedure. The adminState is locked.
The value suspended indicates that the service has been
administratively suspended.
Description of bits:
subjectToTest(0)
partOfServicesLocked(1)
reservedForTest(2)
suspended(3)ro OCTET STRING .1.3.6.1.4.1.562.36.2.1.151.12.1.6 |
mscMmTxAlarmStatusIf supported by the component, this attribute indicates the OSI
Alarm status of the component. Note that, even though it is defined
as a multi-valued set, at most one value is shown to the user.
When no values are in the set, this indicates that either the attribute
is not supported or that none of the status conditions described
below are present.
The value underRepair indicates the component is currently being
repaired. The operationalState is enabled or disabled.
The value critical indicates one or more critical alarms are
outstanding against the component. Other, less severe, alarms may
also be outstanding. The operationalState is enabled or disabled.
The value major indicates one or more major alarms are
outstanding against the component. Other, less severe, alarms may
also be outstanding. The operationalState is enabled or disabled.
The value minor indicates one or more minor alarms are
outstanding against the component. Other, less severe, alarms may
also be outstanding. The operationalState is enabled or disabled.
The value alarmOutstanding generically indicates that an alarm of
some severity is outstanding against the component.
Description of bits:
underRepair(0)
critical(1)
major(2)
minor(3)
alarmOutstanding(4)ro OCTET STRING .1.3.6.1.4.1.562.36.2.1.151.12.1.7 |
mscMmTxStandbyStatusIf supported by the component, this attribute indicates the OSI
Standby status of the component.
The value notSet indicates that either the attribute is not supported
or that none of the status conditions described below are present.
Note that this is a non-standard value, used because the original
specification indicated this attribute was set-valued and thus, did not
provide a value to indicate that none of the other three are
applicable.
The value hotStandby indicates that the resource is not providing
service but will be immediately able to take over the role of the
resource to be backed up, without initialization activity, and
containing the same information as the resource to be backed up.
The value coldStandby indicates the resource is a backup for
another resource but will not be immediately able to take over the
role of the backed up resource and will require some initialization
activity.
The value providingService indicates that this component, as a
backup resource, is currently backing up another resource.ro Enumeration .1.3.6.1.4.1.562.36.2.1.151.12.1.8 |
mscMmTxUnknownStatusThis attribute indicates the OSI Unknown status of the component.
The value false indicates that all of the other OSI State and Status
attribute values can be considered accurate.
The value true indicates that the actual state of the component is not
known for sure.ro Enumeration .1.3.6.1.4.1.562.36.2.1.151.12.1.9 |
mscMmTxOperTableThis group contains status information about the AAL1 Circuit
Emulation Service and the related ATM service, and the means to
specify the Channel to be monitor. SEQUENCE OF MscMmTxOperEntry .1.3.6.1.4.1.562.36.2.1.151.13 |
mscMmTxOperEntryAn entry in the mscMmTxOperTable. MscMmTxOperEntry .1.3.6.1.4.1.562.36.2.1.151.13.1 |
mscMmTxConnectionStatusThis attribute indicates whether a service is non-operational because
of a problem with the service interface side of the service (in which
case, it is set to channelNotReady) or because of a problem with the
ATM side of the service (in which case, it is set to
atmNotConfigured or atmNotReady).
When this attribute is set to channelNotReady, it is an indication
that the corresponding Chan component (as defined by the attribute
interfaceName) or the Chan component's parent port component
(Lp/n Ds1/m or Lp/n E1/m) is locked.
When this attribute is set to atmNotConfigured, it is an indication
that no sub-component has been provisioned, and thus no ATM
connection has been configured for the service.
When this attribute is set to atmNotReady, it is an indication that the
ATM connection with which the service is associated (as defined by
a sub-component) has been lost or that it is currently unable to carry
CES data.
When this attribute is set to channelNotSpecified, it is an indication
that the chanToMonitor attribute is not set to a valid channel.
This attribute is set to connected when a service is operational (that
is, the OSI attribute operationalState is enabled.)ro Enumeration .1.3.6.1.4.1.562.36.2.1.151.13.1.3 |
mscMmTxChanToMonitorchanToMonitor specifies the LP, port (E1 or DS1), and channel to
monitor. The LP must be the same LP specified in the provisionable
attribute linkToLogicalProcessor. This attribute's value is of the
form Lp/x E1/y Chan/z or Lp/x DS1/y Chan/z.rw RowPointer .1.3.6.1.4.1.562.36.2.1.151.13.1.4 |
circuitEmulationServiceMIB OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.2.55 |
IMPORTS Unknown .1.3.6.1.4.1.562.36.2.2.55 |
circuitEmulationServiceGroup OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.2.55.1 |
circuitEmulationServiceGroupCA OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.2.55.1.1 |
circuitEmulationServiceGroupCA02 OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.2.55.1.1.3 |
circuitEmulationServiceGroupCA02A OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.2.55.1.1.3.2 |
circuitEmulationServiceCapabilities OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.2.55.3 |
circuitEmulationServiceCapabilitiesCA OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.2.55.3.1 |
circuitEmulationServiceCapabilitiesCA02 OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.2.55.3.1.3 |
circuitEmulationServiceCapabilitiesCA02A OBJECT IDENTIFIER .1.3.6.1.4.1.562.36.2.2.55.3.1.3.2 |