NETLINK-SPECIFIC-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for NETLINK-SPECIFIC-MIB.
837
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
837 total| Object Name |
|---|
snaDLC OBJECT IDENTIFIER .1.3.6.1.2.1.41 |
IMPORTS Unknown .1.3.6.1.2.1.41 |
sdlc OBJECT IDENTIFIER .1.3.6.1.2.1.41.1 |
sdlcLSGroup OBJECT IDENTIFIER .1.3.6.1.2.1.41.1.2 |
sdlcLSAdminTable OBJECT IDENTIFIER .1.3.6.1.2.1.41.1.2.1 |
sdlcLSAdminEntry OBJECT IDENTIFIER .1.3.6.1.2.1.41.1.2.1.1 |
sdlcLSAddressThis value is the poll address of the
secondary link station for this SDLC link. It
uniquely identifies the SDLC link station
within a single SDLC port.ro INTEGER .1.3.6.1.2.1.41.1.2.1.1.1 |
netlink OBJECT IDENTIFIER .1.3.6.1.4.1.173 |
network OBJECT IDENTIFIER .1.3.6.1.4.1.173.6 |
netstat OBJECT IDENTIFIER .1.3.6.1.4.1.173.6.1 |
nsMaxNeighMaximum number of neighbor nodes. This value is currently
always 64 for FRX8000 and 20 for an N7400 or 7500.
A neighbor is the closest node in a path from the local node.ro INTEGER .1.3.6.1.4.1.173.6.1.1 |
nsThisNodeThis nodes number. (1-250)ro INTEGER .1.3.6.1.4.1.173.6.1.2 |
nsNodTableA table showing all nodes known to this node
along with status and neighbor information. SEQUENCE OF NsEntry .1.3.6.1.4.1.173.6.1.3 |
nsEntryEach entry of the node table is indexed by
node number. NsEntry .1.3.6.1.4.1.173.6.1.3.1 |
nsNodNumThe node number of the desired node. This is the
index into the node table.ro INTEGER .1.3.6.1.4.1.173.6.1.3.1.1 |
nsStatusThe operational status of the node. The status is
given as:
1 = Node is defined in the database;
9 = Node is operational;ro INTEGER .1.3.6.1.4.1.173.6.1.3.1.2 |
nsNumNeighCurrent number of neighbor nodes to this node.ro INTEGER .1.3.6.1.4.1.173.6.1.3.1.3 |
nsNeighTableThe neighbor table lists the status of a nodes
neighbors. SEQUENCE OF NsNeighEntry .1.3.6.1.4.1.173.6.1.4 |
nsNeighEntryThe table entries are indexed by the node number and
the neighbors node number. NsNeighEntry .1.3.6.1.4.1.173.6.1.4.1 |
nsNTNodeThe node number of the node whose neighbor's status
is being sought.ro INTEGER .1.3.6.1.4.1.173.6.1.4.1.1 |
nsNTNeighThe node number of the neighbor whose status is being
sought.ro INTEGER .1.3.6.1.4.1.173.6.1.4.1.2 |
nsNTNeighStatThe status of the neighbor node given as:
1 = previously, but not currently, connected;
2 = Currently connected;ro Enumeration .1.3.6.1.4.1.173.6.1.4.1.3 |
local OBJECT IDENTIFIER .1.3.6.1.4.1.173.7 |
node OBJECT IDENTIFIER .1.3.6.1.4.1.173.7.1 |
nodeCfgTable OBJECT IDENTIFIER .1.3.6.1.4.1.173.7.1.1 |
nodeAlmTable OBJECT IDENTIFIER .1.3.6.1.4.1.173.7.1.2 |
nodeSNMPGroup OBJECT IDENTIFIER .1.3.6.1.4.1.173.7.1.3 |
nodeModelDescribes the unit modelro Enumeration .1.3.6.1.4.1.173.7.1.3.1 |
nodeTrapTextText of the last alarm generatedro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.173.7.1.3.2 |
nodeTrapAdrTableA table used to define the IP address of end-nodes
to receive alarms generated by this node. Up to 16 addresses
can be specified. SEQUENCE OF TpAdrEntry .1.3.6.1.4.1.173.7.1.3.3 |
tpAdrEntryA Trap entry containing objects relating to SNMP traps. TpAdrEntry .1.3.6.1.4.1.173.7.1.3.3.1 |
tpAdrIdxThe index into the trap configuration tablero INTEGER .1.3.6.1.4.1.173.7.1.3.3.1.1 |
tpAddressThe IP Address of the end-station to send alarmsrw IpAddress .1.3.6.1.4.1.173.7.1.3.3.1.2 |
tpAdrFlagDefines the state of this entry as:
0 = Do not send traps to the Address;
1 = Send traps to the Address;
2 = This Address entry is deleted from the table;rw Enumeration .1.3.6.1.4.1.173.7.1.3.3.1.3 |
tpAdrSLevLowest severity level traps that will be sent to
this Address; 1 is the highest, 4 is the lowest.rw Enumeration .1.3.6.1.4.1.173.7.1.3.3.1.4 |
nodeBagTable OBJECT IDENTIFIER .1.3.6.1.4.1.173.7.1.4 |
hwcard OBJECT IDENTIFIER .1.3.6.1.4.1.173.7.2 |
rlpMaxProtosMaximum number of protocols allowed on each RLP.
This value is currently 11 for FRX4000s, 9 for FRX6000s, and
5 for FRX7000s and FRX8000s.ro INTEGER .1.3.6.1.4.1.173.7.2.1 |
rlpConfigTableA Table to describe each RLP on the node SEQUENCE OF RlpEntry .1.3.6.1.4.1.173.7.2.2 |
rlpEntryAn RLP entry containing objects relating to RLPs. RlpEntry .1.3.6.1.4.1.173.7.2.2.1 |
rlpIndexThe RLP number on the nodero INTEGER .1.3.6.1.4.1.173.7.2.2.1.1 |
rlpStatusThe current state of this RLPro Enumeration .1.3.6.1.4.1.173.7.2.2.1.2 |
rlpMemorySizeThe amount of memory installed on this RLPro INTEGER .1.3.6.1.4.1.173.7.2.2.1.3 |
rlpLIC1TypeThe Type of Line Interface card in the first positionro Enumeration .1.3.6.1.4.1.173.7.2.2.1.4 |
rlpLIC2TypeThe Type of Line Interface card in the second positionro Enumeration .1.3.6.1.4.1.173.7.2.2.1.5 |
rlpProtocolThe protocols configured on this RLP. This is an OCTET
STRING where each octet represents a protocol type. The size of this
is the maximum number of protocols allowed on an RLP (rlpMaxProtos).
The protocol types are defined as:
00 = none
01 = X.25
02 = Frame Relay
03 = Async
04 = SDLC
05 = BSC Interactive
07 = IP
08 = SNMP
09 = RIP
0A = LLC2
0B = Trunk
0C = IPX
0D = Config
0E = LLC2-R
0F = IP-R
10 = NVSP
11 = Bridgerw OCTET STRING .1.3.6.1.4.1.173.7.2.2.1.6 |
rlpGroupNumberThe group to which this RLP belongs- always 1 if not
FRX7000.ro INTEGER .1.3.6.1.4.1.173.7.2.2.1.7 |
rlpGroupResponsibilityThe responsibility of this RLP within its group, always
primary if not FRX7000.ro Enumeration .1.3.6.1.4.1.173.7.2.2.1.8 |
port OBJECT IDENTIFIER .1.3.6.1.4.1.173.7.3 |
portX25Group OBJECT IDENTIFIER .1.3.6.1.4.1.173.7.3.1 |
portPhyX25AdminTableThis table contains Netlink Enterprise specific
objects to manage an X25 port. Changing one of
these parameters may take effect in the operating
port immediately or may wait until the interface is
restarted depending on the details of the
implementation.
Most of the objects in this read-write table have
corresponding read-only objects in the
portX25OperTable that return the current
operating value.
The operating values may be different from these
configured values if a configured parameter was
configured after the interface was started. SEQUENCE OF PortPhyX25AdminEntry .1.3.6.1.4.1.173.7.3.1.1 |
portPhyX25AdminEntryA list of configured values for an X25 port. PortPhyX25AdminEntry .1.3.6.1.4.1.173.7.3.1.1.1 |
portPhyX25AdminConnectorPhysical port interface connector type.rw Enumeration .1.3.6.1.4.1.173.7.3.1.1.1.1 |
portPhyX25AdminSpeedThis object defines the speed of the X25 port. The speed may
only be set to one of a series of reasonable values, and if an attempt
is made to set the speed to a value which is within the valid range
but not equal to one of these values, the speed will be rounded up.
If the connector type of the port is RS232, the port could be a
standard port or a high speed port. If the port is a high speed
RS232 port, the maximum valid speed is 256000. If the port is a
standard RS232 port, the maximum valid speed is 64000 on the
FRX4000/SS1840 and 19200 on all other products. It may be possible
to set the speed of a standard RS232 port to a speed which is valid
for a high speed RS232 port but invalid for a standard RS232 port.
In this case, the port may not end up having the invalid speed.
The default speed for a standard RS232 port on the FRX6000 is 19200.rw INTEGER .1.3.6.1.4.1.173.7.3.1.1.1.2 |
portPhyX25AdminGenerateClockSpecifies whether the port will generate the clock
necessary to synchronize traffic over the link.rw Enumeration .1.3.6.1.4.1.173.7.3.1.1.1.3 |
portPhyX25AdminRcvClockFromDTEThis object defines whether the receive clock
will be used from the DTE.rw Enumeration .1.3.6.1.4.1.173.7.3.1.1.1.4 |
portPhyX25AdminDialOutThis flag indicates whether the port is connected to a dial
modem, and whethter connections will be initiated through
dial-in or dial-out calls.rw Enumeration .1.3.6.1.4.1.173.7.3.1.1.1.5 |
portPhyX25AdminInactivityTimerThis timer defines in minutes, the period of inactivity
allowed between calls. Once the timer expires, the port
is disabled untill the next call is placed, if a Dial out
port, or the Disconnect Timer expires, if a Dial in port.
This variable is only meaningful if the port is a Dial port.rw INTEGER .1.3.6.1.4.1.173.7.3.1.1.1.6 |
portPhyX25AdminDisconnectTimerThis timer defines, in seconds, the length of time a
dial-in port will remain disabled after expiration of the
InActivity Timer.rw INTEGER .1.3.6.1.4.1.173.7.3.1.1.1.7 |
portPhyX25AdminSetupTimerThis timer determines the length of time, in seconds, that
a response must be received by the port, after entering the
Linkup state. If a response is not received, the port enters
a Failed state.rw INTEGER .1.3.6.1.4.1.173.7.3.1.1.1.8 |
portPhyX25AdminTrunkFlagThis flag, when set, indicates the port is associated
with a network trunk group. It will be disabled/enabled
if the network trunk is not operational.rw Enumeration .1.3.6.1.4.1.173.7.3.1.1.1.9 |
portPhyX25AdminTrunkGroupThis variable contains a string of 8 bytes, with each
byte indicating 8 ports on an RLP that may be a part of
a trunk group. Since a TurboFrad has only 1 RLP, only the
first byte is valid if the node is an FRX4000. Each
port is represented by a single bit within the RLP byte.
The bit position represents the port number...for example,
if port 2 on RLP 0 was in a trunk group, the first byte of
the string would contain x04 and all other bytes would be 0.rw OCTET STRING .1.3.6.1.4.1.173.7.3.1.1.1.10 |
portPhyX25AdminRowStatusThis variable is used to manage the creation and deletion
of conceptual rows in the portPhyX25AdminTable and follows the
SNMPv2 RowStatus conventions by supporting the following values:
- `active', which indicates that the conceptual row is
available for use by the managed device, and which is
supplied by a management station wishing to exercise an
on-line update of the existing conceptual row. For a
management protocol set operation, a genErr response is
returned when the row does not exist.
- `createAndGo', which is supplied by a management
station wishing to create a new instance of a
conceptual row and to have its status automatically set
to active, making it available for use by the managed
device. For a management protocol set operation, a
genErr response is returned when the row already exists.
- `destroy', which is supplied by a management station
wishing to delete all of the instances associated with
an existing conceptual row.
Note that all of the above values may be specified in a
management protocol set operation, and only the 'active'
value will be returned in response to a management protocol
retrieval operation. For a management protocol set operation,
if other variable bindings are included in the same PDU, then
a genErr response is returned.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.173.7.3.1.1.1.11 |
portPhyX25OperTableThis table contains Netlink Enterprise specific
objects to manage an X25 port. Changing one of
these parameters may take effect in the operating
port immediately or may wait until the interface is
restarted depending on the details of the
implementation.
All of the objects in this table are read-only.
The operating values may be different from these
configured values if a configured parameter was
configured after the interface was started. SEQUENCE OF PortPhyX25OperEntry .1.3.6.1.4.1.173.7.3.1.2 |
portPhyX25OperEntryA list of configured values for an X25 port. PortPhyX25OperEntry .1.3.6.1.4.1.173.7.3.1.2.1 |
portPhyX25OperConnectorPhysical port interface connector type.ro Enumeration .1.3.6.1.4.1.173.7.3.1.2.1.1 |
portPhyX25OperSpeedThis object defines the speed of the X25 port. The speed may
only be set to one of a series of reasonable values, and if an attempt
is made to set the speed to a value which is within the valid range
but not equal to one of these values, the speed will be rounded up.
If the connector type of the port is RS232, the port could be a
standard port or a high speed port. If the port is a high speed
RS232 port, the maximum valid speed is 256000. If the port is a
standard RS232 port, the maximum valid speed is 64000 on the
FRX4000/SS1840 and 19200 on all other products. It may be possible
to set the speed of a standard RS232 port to a speed which is valid
for a high speed RS232 port but invalid for a standard RS232 port.
In this case, the port may not end up having the invalid speed.
The default speed for a standard RS232 port on the FRX6000 is 19200.ro INTEGER .1.3.6.1.4.1.173.7.3.1.2.1.2 |
portPhyX25OperGenerateClockSpecifies whether the port will generate the clock
necessary to synchronize traffic over the link.ro Enumeration .1.3.6.1.4.1.173.7.3.1.2.1.3 |
portPhyX25OperRcvClockFromDTEThis object defines whether the receive clock will be
used from the DTE.ro Enumeration .1.3.6.1.4.1.173.7.3.1.2.1.4 |
portPhyX25OperDialOutThis flag indicates whether the port is connected to a dial
modem, and whethter connections will be initiated through
dial-in or dial-out calls.ro Enumeration .1.3.6.1.4.1.173.7.3.1.2.1.5 |
portPhyX25OperInactivityTimerThis timer defines in minutes, the period of inactivity
allowed between calls. Once the timer expires, the port
is disabled untill the next call is placed, if a Dial out
port, or the Disconnect Timer expires, if a Dial in port.
This variable is only meaningful if the port is a Dial port.ro INTEGER .1.3.6.1.4.1.173.7.3.1.2.1.6 |
portPhyX25OperDisconnectTimerThis timer defines, in seconds, the length of time a
dial-in port will remain disabled after expiration of the
InActivity Timer.ro INTEGER .1.3.6.1.4.1.173.7.3.1.2.1.7 |
portPhyX25OperSetupTimerThis timer determines the length of time, in seconds, that
a response must be received by the port, after entering the
Linkup state. If a response is not received, the port enters
a Failed state.ro INTEGER .1.3.6.1.4.1.173.7.3.1.2.1.8 |
portPhyX25OperTrunkFlagThis flag, when set, indicates the port is associated
with a network trunk group. It will be disabled/enabled
if the network trunk is not operational.ro Enumeration .1.3.6.1.4.1.173.7.3.1.2.1.9 |
portPhyX25OperTrunkGroupThis variable contains a string of 8 bytes, with each
byte indicating a port on this RLP that may be a part of
a trunk group.ro OCTET STRING .1.3.6.1.4.1.173.7.3.1.2.1.10 |
portLogicalX25AdminTableThis table contains Netlink Enterprise specific
objects to manage an X25 Logical port. Changing one of
these parameters may take effect in the operating
port immediately or may wait until the interface is
restarted depending on the details of the
implementation.
The operating values may be different from these
configured values if a configured parameter was
configured after the interface was started. SEQUENCE OF PortLogicalX25AdminEntry .1.3.6.1.4.1.173.7.3.1.3 |
portLogicalX25AdminEntryA list of configured values for an X25 logical port. PortLogicalX25AdminEntry .1.3.6.1.4.1.173.7.3.1.3.1 |
portLogicalX25AdminFrDlciThe DLCI number used to identify the entry in the table. The
range is 16-991.rw INTEGER .1.3.6.1.4.1.173.7.3.1.3.1.1 |
portLogicalX25AdminCxnPriorityThis field sets the priority of the connection among others on the
physical port. The range is 0 for lowest priority to 9 for
the highest priority.rw INTEGER .1.3.6.1.4.1.173.7.3.1.3.1.2 |
portLogicalX25AdminRfc1490This field indicates the encapsulation method usedrw Enumeration .1.3.6.1.4.1.173.7.3.1.3.1.3 |
portLogicalX25AdminBAGAssigns this DLCI to one of sixteen groups whose parameters
regulate bandwidth usage. A 0 value indicates the DLCI does
not use BAGsrw INTEGER .1.3.6.1.4.1.173.7.3.1.3.1.4 |
portLogicalX25AdminRowStatusThis variable is used to manage the creation and deletion
of conceptual rows in the portLogicalX25AdminTable and follows the
SNMPv2 RowStatus conventions by supporting the following values:
- `active', which indicates that the conceptual row is
available for use by the managed device, and which is
supplied by a management station wishing to exercise an
on-line update of the existing conceptual row. For a
management protocol set operation, a genErr response is
returned when the row does not exist.
- `createAndGo', which is supplied by a management
station wishing to create a new instance of a
conceptual row and to have its status automatically set
to active, making it available for use by the managed
device. For a management protocol set operation, a
genErr response is returned when the row already exists.
- `destroy', which is supplied by a management station
wishing to delete all of the instances associated with
an existing conceptual row.
Note that all of the above values may be specified in a
management protocol set operation, and only the 'active'
value will be returned in response to a management protocol
retrieval operation. For a management protocol set operation,
if other variable bindings are included in the same PDU, then
a genErr response is returned.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.173.7.3.1.3.1.5 |
portLogicalX25OperTableThis table contains Netlink Enterprise specific
objects to manage an X25 Logical port. Changing one of
these parameters may take effect in the operating
port immediately or may wait until the interface is
restarted depending on the details of the
implementation.
The operating values may be different from these
configured values if a configured parameter was
configured after the interface was started. SEQUENCE OF PortLogicalX25OperEntry .1.3.6.1.4.1.173.7.3.1.4 |
portLogicalX25OperEntryA list of configured values for an X25 port. PortLogicalX25OperEntry .1.3.6.1.4.1.173.7.3.1.4.1 |
portLogicalX25OperFrDlciThe DLCI number used to identify the entry in the table. The
range is 16-991.ro INTEGER .1.3.6.1.4.1.173.7.3.1.4.1.1 |
portLogicalX25OperCxnPriorityThis field sets the priority of the connection among others on the
physical port. The range is 0 for lowest priority to 9 for
the highest priority.ro INTEGER .1.3.6.1.4.1.173.7.3.1.4.1.2 |
portLogicalX25OperRfc1490This field indicates the encapsulation method usedro Enumeration .1.3.6.1.4.1.173.7.3.1.4.1.3 |
portLogicalX25OperBAGAssigns this DLCI to one of sixteen groups whose parameters
regulate bandwidth usage.ro INTEGER .1.3.6.1.4.1.173.7.3.1.4.1.4 |
portX25AdminTableThis table contains Netlink Enterprise specific
objects to manage an X25 port. Changing one of
these parameters may take effect in the operating
port immediately or may wait until the interface is
restarted depending on the details of the
implementation.
Most of the objects in this read-write table have
corresponding read-only objects in the
portX25OperTable that return the current
operating value.
The operating values may be different from these
configured values if a configured parameter was
configured after the interface was started. SEQUENCE OF PortX25AdminEntry .1.3.6.1.4.1.173.7.3.1.5 |
portX25AdminEntryA list of configured values for an X25 port. PortX25AdminEntry .1.3.6.1.4.1.173.7.3.1.5.1 |
portX25AdminBlockedFlagA flag which when set, means the port should not be
enabled after a boot-up of the node.rw Enumeration .1.3.6.1.4.1.173.7.3.1.5.1.1 |
portX25AdminFlowCtrlNegA flag which if set, permits negotiation of
the flow control parameters on a per call basis.
If N is selected, the default packet and window
sizes will be used. If Y is selected, the packet
or window size in a call packet (up to the
configured Max Packet Size or Max Window Size) is
used.rw Enumeration .1.3.6.1.4.1.173.7.3.1.5.1.2 |
portX25AdminThruptClassNegA flag which ,if set, permists negotiation of
the throughput class for either direction of
data transmission on a per call basis. If N is
selected, the configured Max Throughput Class
value is used. If Y, any throughput class in
a call packet (up to the Max Thruput Class) is
used.rw Enumeration .1.3.6.1.4.1.173.7.3.1.5.1.3 |
portX25AdminLocChgPrevIf Y is selected, no calls can be charged to
port. Incoming calls from the network with
reverse charge specified will be rejected. Outgoing
calls will insert reverse charge in the call packet
if not already included.rw Enumeration .1.3.6.1.4.1.173.7.3.1.5.1.4 |
portX25AdminRevChgAccptA flag, if set, that authorizes transmission of
incoming calls that request the reverse charge
facility. If N is selected, and a call requests
it, it will not be transmitted.rw Enumeration .1.3.6.1.4.1.173.7.3.1.5.1.5 |
portX25AdminFastSelAccptA flag, if set, that authorizes transmission of
incoming calls that request the Fast Select
facility.rw Enumeration .1.3.6.1.4.1.173.7.3.1.5.1.6 |
portX25AdminInCallBarAn X25 facility that prevents transmission of
incoming calls to the local DTE.rw Enumeration .1.3.6.1.4.1.173.7.3.1.5.1.7 |
portX25AdminOutCallBarAn X25 facility that prevents transmission of
incoming calls to the local DTE.rw Enumeration .1.3.6.1.4.1.173.7.3.1.5.1.8 |
portX25AdminMaxPktSizeThe maximum data packet size that will be allowed to pass
through this port.rw INTEGER .1.3.6.1.4.1.173.7.3.1.5.1.9 |
portX25AdminDefPktSizeThis is the size that will be assigned to an incoming call
setup packet if the packet does not request a packet size.rw INTEGER .1.3.6.1.4.1.173.7.3.1.5.1.10 |
portX25AdminMaxWinSizeThis is the maximum number of unacknowledged packets
per logical channel that can pass through this port.rw INTEGER .1.3.6.1.4.1.173.7.3.1.5.1.11 |
portX25AdminDefWinSizeThis size will be assigned to an incoming call
setup packet if the packet doesn't request a window size.rw INTEGER .1.3.6.1.4.1.173.7.3.1.5.1.12 |
portX25AdminMaxThruptClassThis specifies the default throughput class that will be
inserted into a Call Request packet if Thruput Class
negotiation is not enabled or if a thruput class is not
requested in the call request.rw INTEGER .1.3.6.1.4.1.173.7.3.1.5.1.13 |
portX25AdminCUGPrefThis flag, if set, indicates the port belongs to at least
one CUG.rw Enumeration .1.3.6.1.4.1.173.7.3.1.5.1.14 |
portX25AdminCUGIndexThis number is an index into a Closed User Group table
which identifies the default Closed User Group for the
port.rw INTEGER .1.3.6.1.4.1.173.7.3.1.5.1.15 |
portX25AdminCUGIncAccessThis flag, when set, indicates whether this port will
be allowed to receive calls from outside its CUGs.rw Enumeration .1.3.6.1.4.1.173.7.3.1.5.1.16 |
portX25AdminCUGOutAccessThis flag, when set, indicates whether this port will
be allowed to make calls outside its CUGs.rw Enumeration .1.3.6.1.4.1.173.7.3.1.5.1.17 |
portX25OperTableThis table contains Netlink Enterprise specific
objects to manage an X25 port. Changing one of
these parameters may take effect in the operating
port immediately or may wait until the interface is
restarted depending on the details of the
implementation.
The objects in this read-only table
corresponding read-only objects in the
portX25OperTable that return the current
operating value.
The operating values may be different from these
configured values if a configured parameter was
configured after the interface was started. SEQUENCE OF PortX25OperEntry .1.3.6.1.4.1.173.7.3.1.6 |
portX25OperEntryA list of configured values for an X25 port. PortX25OperEntry .1.3.6.1.4.1.173.7.3.1.6.1 |
portX25OperBlockedFlagA flag which when set, means the port should not be
enabled after a boot-up of the node.ro Enumeration .1.3.6.1.4.1.173.7.3.1.6.1.1 |
portX25OperFlowCtrlNegA flag which if set, permits negotiation of
the flow control parameters on a per call basis.
If N is selected, the default packet and window
sizes will be used. If Y is selected, the packet
or window size in a call packet (up to the
configured Max Packet Size or Max Window Size) is
used.ro Enumeration .1.3.6.1.4.1.173.7.3.1.6.1.2 |
portX25OperThruptClassNegA flag which ,if set, permists negotiation of
the throughput class for either direction of
data transmission on a per call basis. If N is
selected, the configured Max Throughput Class
value is used. If Y, any throughput class in
a call packet (up to the Max Thruput Class) is
used.ro Enumeration .1.3.6.1.4.1.173.7.3.1.6.1.3 |
portX25OperLocChgPrevIf Y is selected, no calls can be charged to
port. Incoming calls from the network with
reverse charge specified will be rejected. Outgoing
calls will insert reverse charge in the call packet
if not already included.ro Enumeration .1.3.6.1.4.1.173.7.3.1.6.1.4 |
portX25OperRevChgAccptA flag, if set, that authorizes transmission of
incoming calls that request the reverse charge
facility. If N is selected, and a call requests
it, it will not be transmitted.ro Enumeration .1.3.6.1.4.1.173.7.3.1.6.1.5 |
portX25OperFastSelAccptA flag, if set, that authorizes transmission of
incoming calls that request the Fast Select
facility.ro Enumeration .1.3.6.1.4.1.173.7.3.1.6.1.6 |
portX25OperInCallBarAn X25 facility that prevents transmission of
incoming calls to the local DTE.ro Enumeration .1.3.6.1.4.1.173.7.3.1.6.1.7 |
portX25OperOutCallBarAn X25 facility that prevents transmission of
incoming calls to the local DTE.ro Enumeration .1.3.6.1.4.1.173.7.3.1.6.1.8 |
portX25OperMaxPktSizeThe maximum data packet size that will be allowed to pass
through this port.ro INTEGER .1.3.6.1.4.1.173.7.3.1.6.1.9 |
portX25OperDefPktSizeThis is the size that will be assigned to an incoming call
setup packet if the packet does not request a packet size.ro INTEGER .1.3.6.1.4.1.173.7.3.1.6.1.10 |
portX25OperMaxWinSizeThis is the maximum number of unacknowledged packets
per logical channel that can pass through this port.ro INTEGER .1.3.6.1.4.1.173.7.3.1.6.1.11 |
portX25OperDefWinSizeThis size will be assigned to an incoming call
setup packet if the packet doesn't request a window size.ro INTEGER .1.3.6.1.4.1.173.7.3.1.6.1.12 |
portX25OperMaxThruptClassThis specifies the default throughput class that will be
inserted into a Call Request packet if Thruput Class
negotiation is not enabled or if a thruput class is not
requested in the call request.ro INTEGER .1.3.6.1.4.1.173.7.3.1.6.1.13 |
portX25OperCUGPrefThis flag, if set, indicates the port belongs to at least
one CUG.ro Enumeration .1.3.6.1.4.1.173.7.3.1.6.1.14 |
portX25OperCUGIndexThis number is an index into a Closed User Group table
which identifies the default Closed User Group for the
port.ro INTEGER .1.3.6.1.4.1.173.7.3.1.6.1.15 |
portX25OperCUGIncAccessThis flag, when set, indicates whether this port will
be able to receive calls from outside its CUGs.ro Enumeration .1.3.6.1.4.1.173.7.3.1.6.1.16 |
portX25OperCUGOutAccessThis flag, when set, indicates whether this port will
be able to make calls outside its CUGs.ro Enumeration .1.3.6.1.4.1.173.7.3.1.6.1.17 |
portFrGroup OBJECT IDENTIFIER .1.3.6.1.4.1.173.7.3.2 |
portFrConfigTableA list of Frame Relay ports . The number of
entries will be the number of Frame Relay ports on the node. SEQUENCE OF PortFrEntry .1.3.6.1.4.1.173.7.3.2.1 |
portFrEntryAn Frame Relay Port entry containing objects
relating to the port that are configurable
by the user. PortFrEntry .1.3.6.1.4.1.173.7.3.2.1.1 |
portFrRlpIndexThe RLP number of the Frame Relay port. It will be in the
range 1-8.ro INTEGER .1.3.6.1.4.1.173.7.3.2.1.1.1 |
portFrPortIndexThe Port number of the Frame Relay port. It will
be in the range 1-8 for a physical port. It will be in the range
9-64 for a Frame Relay logical port.ro INTEGER .1.3.6.1.4.1.173.7.3.2.1.1.2 |
portFrBlockedFlagA flag which when set, means the port should not be
enabled after a boot-up of the node.rw Enumeration .1.3.6.1.4.1.173.7.3.2.1.1.3 |
portFrMaxBytesPerFrameThe maximum number of bytes allowed in an I Frame for this
Frame Relay port.rw INTEGER .1.3.6.1.4.1.173.7.3.2.1.1.4 |
portFrT392TimerThis timer indicates how long the network will wait between
Status Enquiry messages before recording an error. It
should be greater than or equal to the frDlcmiPollingInterval
variable in the RFC1315 Mib.rw INTEGER .1.3.6.1.4.1.173.7.3.2.1.1.5 |
portFrOutgoingRateControlThis is a flag which, when set, enables the enforcement of
the Outgoing Rate Control parameters.rw Enumeration .1.3.6.1.4.1.173.7.3.2.1.1.6 |
portFrBandwidthAllocationThis is a flag which, when set, enables whether the bandwidth
allocation will be enforced.rw Enumeration .1.3.6.1.4.1.173.7.3.2.1.1.7 |
portFrConnectorThis defines the connector type of the Frame Relay port.rw Enumeration .1.3.6.1.4.1.173.7.3.2.1.1.8 |
portFrLogicalDCEThis defines the port as logical DCE or DTE.rw Enumeration .1.3.6.1.4.1.173.7.3.2.1.1.9 |
portFrGenClockThis specifies whether the port will generate the clock
necessary to synchronize traffic over the link.rw Enumeration .1.3.6.1.4.1.173.7.3.2.1.1.10 |
portFrRcvClkFrmDTEThis allows the clock to be looped back from the DTE using
the TT (Terminal Timing) signal, which can be helpful on
high-speed lines.rw Enumeration .1.3.6.1.4.1.173.7.3.2.1.1.11 |
portFrLLMThis determines whether, and what type of, configurable
network management (status enquiries) will be allowed.rw Enumeration .1.3.6.1.4.1.173.7.3.2.1.1.12 |
portFrRowStatusThis variable is used to manage the creation and deletion
of conceptual rows in the portFrConfigTable and follows the
SNMPv2 RowStatus conventions by supporting the following values:
- `active', which indicates that the conceptual row is
available for use by the managed device, and which is
supplied by a management station wishing to exercise an
on-line update of the existing conceptual row. For a
management protocol set operation, a genErr response is
returned when the row does not exist.
- `createAndGo', which is supplied by a management
station wishing to create a new instance of a
conceptual row and to have its status automatically set
to active, making it available for use by the managed
device. For a management protocol set operation, a
genErr response is returned when the row already exists.
- `destroy', which is supplied by a management station
wishing to delete all of the instances associated with
an existing conceptual row.
Note that all of the above values may be specified in a
management protocol set operation, and only the 'active'
value will be returned in response to a management protocol
retrieval operation. For a management protocol set operation,
if other variable bindings are included in the same PDU, then
a genErr response is returned.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.173.7.3.2.1.1.13 |
portFrSpeedThis object defines the speed of the Frame Relay port. The speed may
only be set to one of a series of reasonable values, and if an attempt is made
to set the speed to a value which is within the valid range but not equal to one
of these values, the speed will be rounded up. If the connector type of the port
is RS232, the port could be a standard port or a high speed port. If the port is
a high speed RS232 port, the maximum valid speed is 256000. If the port is a standard
RS232 port, the maximum valid speed is 64000 on the FRX4000/SS1840 and 19200
on all other products. It may be possible to set the speed of a standard RS232 port
to a speed which is valid for a high speed RS232 port but invalid for a standard
RS232 port. In this case, the port may not end up having the invalid speed. The default
speed for a standard RS232 port on the FRX6000 is 19200.rw INTEGER .1.3.6.1.4.1.173.7.3.2.1.1.14 |
portFrBackupUseOnlyThis object determines whether all DLCIs on the port will
be reserved exclusively as backups for other DLCIs in the
same node. If yes is specified for this object, the port
will remain disabled until needed for backup.rw Enumeration .1.3.6.1.4.1.173.7.3.2.1.1.15 |
portDLCIConfigTableA list of DLCI's on Frame Relay ports . The number of
entries will be the number of DLCIs on all the Frame Relay
ports on a node. SEQUENCE OF PortDLCIEntry .1.3.6.1.4.1.173.7.3.2.2 |
portDLCIEntryAn Frame Relay Port DLCI entry
relating to the Rate Control Information that is configurable
by the user. PortDLCIEntry .1.3.6.1.4.1.173.7.3.2.2.1 |
portDLCIRlpIndexThe RLP number on which the DLCI is located. The range for
this is 1-8.ro INTEGER .1.3.6.1.4.1.173.7.3.2.2.1.1 |
portDLCIPortIndexThe port number on which the DLCI is located. The range for
this is 1-8 for a physical FR port and 9-64 for a logical FR port.ro INTEGER .1.3.6.1.4.1.173.7.3.2.2.1.2 |
portDLCIIndexThe DLCI number used to identify the entry in the table. The
range is 16-991.ro INTEGER .1.3.6.1.4.1.173.7.3.2.2.1.3 |
portDLCIIncomingCIRThe committed information rate that is supported on the
DLCI for incoming data.rw INTEGER .1.3.6.1.4.1.173.7.3.2.2.1.4 |
portDLCIOutgoingCIRThe committed information rate that is supported on the
DLCI for outgoing data.rw INTEGER .1.3.6.1.4.1.173.7.3.2.2.1.5 |
portDLCIIncomingBcThe committed burst size is the maximum amount of data
to be transmitted under normal conditions within the time
period defined by Bc/Cir that is supported on the
DLCI for incoming data.rw INTEGER .1.3.6.1.4.1.173.7.3.2.2.1.6 |
portDLCIOutgoingBcThe committed burst size is the maximum amount of data
to be transmitted under normal conditions within the time
period defined by Bc/Cir that is supported on the
DLCI for Outgoing data.rw INTEGER .1.3.6.1.4.1.173.7.3.2.2.1.7 |
portDLCIIncomingBeThe excess burst size is the maximum amount of incoming data
in excess of the committed burst size that the network will try to
transfer during the time interval determined by Bc/Cir on this
DLCI.rw INTEGER .1.3.6.1.4.1.173.7.3.2.2.1.8 |
portDLCIOutgoingBeThe excess burst size is the maximum amount of incoming data
in excess of the committed burst size that the network will try to
transfer during the time interval determined by Bc/Cir on this
DLCI.rw INTEGER .1.3.6.1.4.1.173.7.3.2.2.1.9 |
portDLCIBecnRecoveryCntThe BECN recovery Count is a method of controlling the rate
of return to max traffic flow after it has been reduced due to
congestion. The value determines the number of packets received
sequentially without BECN set, before increasing the Excess Burst
Size by 1/8 of it's configured value.rw INTEGER .1.3.6.1.4.1.173.7.3.2.2.1.10 |
portDLCIPriorityThis field sets the priority of the DLCI among others on the
physical port. The range is 0 for lowest priority to 4 for
the highest priority.rw INTEGER .1.3.6.1.4.1.173.7.3.2.2.1.11 |
portDLCIRowStatusThis variable is used to manage the creation and deletion
of conceptual rows in the portDLCIConfigTable and follows the
SNMPv2 RowStatus conventions by supporting the following values:
- `active', which indicates that the conceptual row is
available for use by the managed device. For a management
protocol set operation, a genErr response is returned when
the row does not exist.
- `createAndGo', which is supplied by a management
station wishing to create a new instance of a
conceptual row and to have its status automatically set
to active, making it available for use by the managed
device. For a management protocol set operation, a
genErr response is returned when the row already exists.
- `destroy', which is supplied by a management station
wishing to delete all of the instances associated with
an existing conceptual row.
Note that all of the above values may be specified in a
management protocol set operation, and only the 'active'
value will be returned in response to a management protocol
retrieval operation. For a management protocol set operation,
if other variable bindings are included in the same PDU, then
a genErr response is returned.
Also note that deleting a DLCI entry will only remove it from
the database file, and it's existence will still be known by
the protocol until the node is rebooted.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.173.7.3.2.2.1.12 |
portDLCIBackupGroupThis object specifies (if configured as any number other than
zero) that this is a primary DLCI, and identifies the backup
DLCI(s) (in a Frame Relay backup group) that will take over if
this DLCI fails. This is applicable only on an initiating node,
which is the node that will initiate the switchover to a backup
DLCI. At switchover, the initiating node notifies the remote
node of the change.rw INTEGER .1.3.6.1.4.1.173.7.3.2.2.1.13 |
portDLCIBackupProtEnbThis object specifies whether the DLCI will be used as a
non-initiating backup DLCI. The DLCI will wait for a backup
protocol message from the initiating end, telling the backup
where to send the rest of the messages.rw Enumeration .1.3.6.1.4.1.173.7.3.2.2.1.14 |
portFrBackupGroupTableA Table describes the Frame Relay Backup MIB . SEQUENCE OF FrBackupEntry .1.3.6.1.4.1.173.7.3.2.3 |
portFrBackupEntryThis Entry contains the SNMP objects that are used for
configurating the Frame Relay Backup. FrBackupEntry .1.3.6.1.4.1.173.7.3.2.3.1 |
portFrBackupRLPThis RLP number identifies the RLP containing the
primary and backup DLCIs.ro INTEGER .1.3.6.1.4.1.173.7.3.2.3.1.1 |
portFrBackupPortThis Port number is the physical port on which
the backup DLCI is being configured.ro INTEGER .1.3.6.1.4.1.173.7.3.2.3.1.2 |
portFrBackupDLCIThis DLCI number is the backup being configured.ro INTEGER .1.3.6.1.4.1.173.7.3.2.3.1.3 |
portFrBackupGroupThis Group number is the backup being configured.ro INTEGER .1.3.6.1.4.1.173.7.3.2.3.1.4 |
portFrBackupWaitTimerThis is the time after a primary DLCI failure that the
software will wait for this DLCI to become active before
checking the next backup DLCI. If the backup does not
become active before the timer expires, the software will
search the backup group for the next available backup.rw INTEGER .1.3.6.1.4.1.173.7.3.2.3.1.5 |
portFrBackupProtEnabThis enables or disables the backup protocol on the specified
DLCI. It should be set to yes if and only if the remote device
is an FRX4000 or FRX6000 with the backup protocol enabled on the
remote DLCI connected to this backup group entry.rw Enumeration .1.3.6.1.4.1.173.7.3.2.3.1.6 |
portFrBackupRowStatusThis variable is used to manage the creation and deletion
of conceptual rows in the portFrBackupGroupTable and follows the
SNMPv2 RowStatus conventions by supporting the following values:
- `active', which indicates that the conceptual row is
available for use by the managed device. For a management
protocol set operation, a genErr response is returned when
the row does not exist.
- `createAndGo', which is supplied by a management
station wishing to create a new instance of a
conceptual row and to have its status automatically set
to active, making it available for use by the managed
device. For a management protocol set operation, a
genErr response is returned when the row already exists.
- `destroy', which is supplied by a management station
wishing to delete all of the instances associated with
an existing conceptual row.
Note that all of the above values may be specified in a
management protocol set operation, and only the 'active'
value will be returned in response to a management protocol
retrieval operation. For a management protocol set operation,
if other variable bindings are included in the same PDU, then
a genErr response is returned.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.173.7.3.2.3.1.7 |
portBsciGroup OBJECT IDENTIFIER .1.3.6.1.4.1.173.7.3.4 |
portBsciAdminTableA list of BSC Interactive ports . The number of
entries will be the number of BSC Interactive ports on the node. SEQUENCE OF PortBsciAdminEntry .1.3.6.1.4.1.173.7.3.4.1 |
portBsciAdminEntryA BSCI Interactive Port entry containing objects
relating to the port that are configurable by the user. PortBsciAdminEntry .1.3.6.1.4.1.173.7.3.4.1.1 |
portBsciAdminBlockedFlagCauses the port to be enabled or disabled at node IPL.rw Enumeration .1.3.6.1.4.1.173.7.3.4.1.1.1 |
portBsciAdminConnectorPhysical port interface connector type.rw Enumeration .1.3.6.1.4.1.173.7.3.4.1.1.2 |
portBsciAdminSpeedData transmission rate in bits per second.rw INTEGER .1.3.6.1.4.1.173.7.3.4.1.1.3 |
portBsciAdminRetransmitIntervalLength of time before the node will transmit an I-frame
if the previous transmission is not acknowledged.rw INTEGER .1.3.6.1.4.1.173.7.3.4.1.1.4 |
portBsciAdminMAXRetransmitsMaximum number of times the node will attempt to send
an I-frame after a retransmission period expiration.rw INTEGER .1.3.6.1.4.1.173.7.3.4.1.1.5 |
portBsciAdminMaxBytesPerFrameMaximum frame size that will be transmitted on the port.rw INTEGER .1.3.6.1.4.1.173.7.3.4.1.1.6 |
portBsciAdminGenerateClockSpecifies whether the port will generate the clock
necessary to synchronize traffic over the link.rw Enumeration .1.3.6.1.4.1.173.7.3.4.1.1.7 |
portBsciAdminRcvClockFromDTEAllows the clock to be looped back from the DTE
using the TT (Terminal Timing) signal.rw Enumeration .1.3.6.1.4.1.173.7.3.4.1.1.8 |
portBsciAdminPadTypeBSCI Pad Typerw Enumeration .1.3.6.1.4.1.173.7.3.4.1.1.9 |
portBsciAdminUseEBCDICSpecifies whether all devices on a line use the same
character set for successive session polls.rw Enumeration .1.3.6.1.4.1.173.7.3.4.1.1.10 |
portBsciAdminCallInfoInRequestPacketSpecifies whether the user will have the option of
including call information in a call request packet.rw Enumeration .1.3.6.1.4.1.173.7.3.4.1.1.11 |
portBsciAdminClearVCOnLastDeviceDownCauses the virtual circuit to be cleared when no
terminals are using it.rw Enumeration .1.3.6.1.4.1.173.7.3.4.1.1.12 |
portBsciAdminTransTextSupportedCauses all characters transmitted to be treated as data.rw Enumeration .1.3.6.1.4.1.173.7.3.4.1.1.13 |
portBsciAdminEndToEndAckAllows management of acknowledgments end to end across
the network rather than locally at each end.rw Enumeration .1.3.6.1.4.1.173.7.3.4.1.1.14 |
portBsciAdminFullDuplexSpecifies full-duplex transmission.rw Enumeration .1.3.6.1.4.1.173.7.3.4.1.1.15 |
portBsciAdminMultidropSpecifies whether transmission will be multidrop.rw Enumeration .1.3.6.1.4.1.173.7.3.4.1.1.16 |
portBsciAdminSlowPollRetryCountSpecifies how many times the control unit will be polled
before it is put on the slow poll list.rw INTEGER .1.3.6.1.4.1.173.7.3.4.1.1.17 |
portBsciAdminSlowPollRetryFreqSpecifies the number of times active control units will
be polled between pollings on the slow poll list.rw INTEGER .1.3.6.1.4.1.173.7.3.4.1.1.18 |
portBsciAdminStartSynchCharsSpecifies the number of synchronization characters
that will be added to the beginning of each frame.rw INTEGER .1.3.6.1.4.1.173.7.3.4.1.1.19 |
portBsciAdminEndPadCharsSpecifies the number of padding characters that will
be added to the end of each frame.rw INTEGER .1.3.6.1.4.1.173.7.3.4.1.1.20 |
portBsciAdminPollIntervalSpecifies the time between passes through the polling list.rw INTEGER .1.3.6.1.4.1.173.7.3.4.1.1.21 |
portBsciAdminNoResponseTimerActivated after transmission of a general poll or a
data frame.rw INTEGER .1.3.6.1.4.1.173.7.3.4.1.1.22 |
portBsciAdminNoResponseRetryCountSpecifies how many times the user device will be polled
before control is passed on the next cluster.rw INTEGER .1.3.6.1.4.1.173.7.3.4.1.1.23 |
portBsciAdminErrorRetransmitCountSpecifies the number of times the Netlink device will
resend a block of data after the receiving device has
detected an error in that block.rw INTEGER .1.3.6.1.4.1.173.7.3.4.1.1.24 |
portBsciAdminNAKRetryCountSpecifies the number of times the Netlink device will
send a frame when the receiving device is unable to
acknowledge.rw INTEGER .1.3.6.1.4.1.173.7.3.4.1.1.25 |
portBsciAdminBlockCheckSets the redundancy check parameter.rw Enumeration .1.3.6.1.4.1.173.7.3.4.1.1.26 |
portBsciAdminDataModeSets the parity parameter.rw Enumeration .1.3.6.1.4.1.173.7.3.4.1.1.27 |
portBsciAdminRowStatusThis variable is used to manage the creation and deletion
of conceptual rows in the portBsciAdminTable and follows the
SNMPv2 RowStatus conventions by supporting the following values:
- `active', which indicates that the conceptual row is
available for use by the managed device, and which is
supplied by a management station wishing to exercise an
on-line update of the existing conceptual row. For a
management protocol set operation, a genErr response is
returned when the row does not exist.
- `createAndGo', which is supplied by a management
station wishing to create a new instance of a
conceptual row and to have its status automatically set
to active, making it available for use by the managed
device. For a management protocol set operation, a
genErr response is returned when the row already exists.
- `destroy', which is supplied by a management station
wishing to delete all of the instances associated with
an existing conceptual row.
Note that all of the above values may be specified in a
management protocol set operation, and only the 'active'
value will be returned in response to a management protocol
retrieval operation. For a management protocol set operation,
if other variable bindings are included in the same PDU, then
a genErr response is returned.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.173.7.3.4.1.1.28 |
portBsciAdminAnswerNonConfiguredOnly valid if pad type is HPAD. If yes, the HPAD will
respond to all devices on the line. If no, the HPAD will
respond only to those devices that are configured on the
node.rw Enumeration .1.3.6.1.4.1.173.7.3.4.1.1.29 |
portBsciAdminActivateConnectionWithoutPollOnly valid if pad type is TPAD. If yes, will active the
TPAD connection without a poll of the connected device.rw Enumeration .1.3.6.1.4.1.173.7.3.4.1.1.30 |
portBsciOperTableA list of BSC Interactive ports . The number of
entries will be the number of BSC Interactive ports on the node. SEQUENCE OF PortBsciOperEntry .1.3.6.1.4.1.173.7.3.4.2 |
portBsciOperEntryA BSCI Interactive Port entry containing objects
relating to the port that are configurable by the user. PortBsciOperEntry .1.3.6.1.4.1.173.7.3.4.2.1 |
portBsciOperBlockedFlagCauses the port to be enabled or disabled at node IPL.ro Enumeration .1.3.6.1.4.1.173.7.3.4.2.1.1 |
portBsciOperConnectorPhysical port interface connector type.ro Enumeration .1.3.6.1.4.1.173.7.3.4.2.1.2 |
portBsciOperSpeedData transmission rate in bits per second.ro INTEGER .1.3.6.1.4.1.173.7.3.4.2.1.3 |
portBsciOperRetransmitIntervalLength of time before the node will transmit an I-frame
if the previous transmission is not acknowledged.ro INTEGER .1.3.6.1.4.1.173.7.3.4.2.1.4 |
portBsciOperMAXRetransmitsMaximum number of times the node will attempt to send
an I-frame after a retransmission period expiration.ro INTEGER .1.3.6.1.4.1.173.7.3.4.2.1.5 |
portBsciOperMaxBytesPerFrameMaximum frame size that will be transmitted on the port.ro INTEGER .1.3.6.1.4.1.173.7.3.4.2.1.6 |
portBsciOperGenerateClockSpecifies whether the port will generate the clock
necessary to synchronize traffic over the link.ro Enumeration .1.3.6.1.4.1.173.7.3.4.2.1.7 |
portBsciOperRcvClockFromDTEAllows the clock to be looped back from the DTE
using the TT (Terminal Timing) signal.ro Enumeration .1.3.6.1.4.1.173.7.3.4.2.1.8 |
portBsciOperPadTypeBSCI Pad Typero Enumeration .1.3.6.1.4.1.173.7.3.4.2.1.9 |
portBsciOperUseEBCDICSpecifies whether all devices on a line use the same
character set for successive session polls.ro Enumeration .1.3.6.1.4.1.173.7.3.4.2.1.10 |
portBsciOperCallInfoInRequestPacketSpecifies whether the user will have the option of
including call information in a call request packet.ro Enumeration .1.3.6.1.4.1.173.7.3.4.2.1.11 |
portBsciOperClearVCOnLastDeviceDownCauses the virtual circuit to be cleared when no
terminals are using it.ro Enumeration .1.3.6.1.4.1.173.7.3.4.2.1.12 |
portBsciOperTransTextSupportedCauses all characters transmitted to be treated as data.ro Enumeration .1.3.6.1.4.1.173.7.3.4.2.1.13 |
portBsciOperEndToEndAckAllows management of acknowledgments end to end across
the network rather than locally at each end.ro Enumeration .1.3.6.1.4.1.173.7.3.4.2.1.14 |
portBsciOperFullDuplexSpecifies full-duplex transmission.ro Enumeration .1.3.6.1.4.1.173.7.3.4.2.1.15 |
portBsciOperMultidropSpecifies whether transmission will be multidrop.ro Enumeration .1.3.6.1.4.1.173.7.3.4.2.1.16 |
portBsciOperSlowPollRetryCountSpecifies how many times the control unit will be polled
before it is put on the slow poll list.ro INTEGER .1.3.6.1.4.1.173.7.3.4.2.1.17 |
portBsciOperSlowPollRetryFreqSpecifies the number of times active control units will
be polled between pollings on the slow poll list.ro INTEGER .1.3.6.1.4.1.173.7.3.4.2.1.18 |
portBsciOperStartSynchCharsSpecifies the number of synchronization characters
that will be added to the beginning of each frame.ro INTEGER .1.3.6.1.4.1.173.7.3.4.2.1.19 |
portBsciOperEndPadCharsSpecifies the number of padding characters that will
be added to the end of each frame.ro INTEGER .1.3.6.1.4.1.173.7.3.4.2.1.20 |
portBsciOperPollIntervalSpecifies the time between passes through the polling list.ro INTEGER .1.3.6.1.4.1.173.7.3.4.2.1.21 |
portBsciOperNoResponseTimerActivated after transmission of a general poll or a
data frame.ro INTEGER .1.3.6.1.4.1.173.7.3.4.2.1.22 |
portBsciOperNoResponseRetryCountSpecifies how many times the user device will be polled
before control is passed on the next cluster.ro INTEGER .1.3.6.1.4.1.173.7.3.4.2.1.23 |
portBsciOperErrorRetransmitCountSpecifies the number of times the Netlink device will
resend a block of data after the receiving device has
detected an error in that block.ro INTEGER .1.3.6.1.4.1.173.7.3.4.2.1.24 |
portBsciOperNAKRetryCountSpecifies the number of times the Netlink device will
send a frame when the receiving device is unable to
acknowledge.ro INTEGER .1.3.6.1.4.1.173.7.3.4.2.1.25 |
portBsciOperBlockCheckSets the redundancy check parameter.ro Enumeration .1.3.6.1.4.1.173.7.3.4.2.1.26 |
portBsciOperDataModeSets the parity parameter.ro Enumeration .1.3.6.1.4.1.173.7.3.4.2.1.27 |
portBsciOperAnswerNonConfiguredOnly valid if pad type is HPAD. If yes, the HPAD will
respond to all devices on the line. If no, the HPAD will
respond only to those devices that are configured on the
node.ro Enumeration .1.3.6.1.4.1.173.7.3.4.2.1.28 |
portBsciOperActivateConnectionWithoutPollOnly valid if pad type is TPAD. If yes, will active the
TPAD connection without a poll of the connected device.ro Enumeration .1.3.6.1.4.1.173.7.3.4.2.1.29 |
bsciSubscrAdminTableA list of BSC Interactive port subscribers. SEQUENCE OF BsciSubscrAdminEntry .1.3.6.1.4.1.173.7.3.4.3 |
bsciSubscrAdminEntryA BSCI Interactive Port Subscriber entry containing objects
relating to the port that are configurable by the user. BsciSubscrAdminEntry .1.3.6.1.4.1.173.7.3.4.3.1 |
bsciSubscrAdminSequenceSubscriber index for a specific BSCI port subscriber.ro INTEGER .1.3.6.1.4.1.173.7.3.4.3.1.1 |
bsciSubscrAdminLocalIDSubscriber address of the local end of a BSCI connection.rw NlSubscriberAddress .1.3.6.1.4.1.173.7.3.4.3.1.2 |
bsciSubscrAdminRemoteIDSubscriber address of the remote end of a BSCI connection.rw NlSubscriberAddress .1.3.6.1.4.1.173.7.3.4.3.1.3 |
bsciSubscrAdminAutocallCauses a BSCI TPAD to automatically call its HPAD when
the controller becomes active.rw Enumeration .1.3.6.1.4.1.173.7.3.4.3.1.4 |
bsciSubscrAdminAutocallRtyTimerTime between autocall retries.rw INTEGER .1.3.6.1.4.1.173.7.3.4.3.1.5 |
bsciSubscrAdminAutocallMaxRtryMaximum number of times an autocall will be sent.rw INTEGER .1.3.6.1.4.1.173.7.3.4.3.1.6 |
bsciSubscrAdminConnectionIDIdentifier that will link the BSCI port with a device
configured in the BSCI Devices Table.rw INTEGER .1.3.6.1.4.1.173.7.3.4.3.1.7 |
bsciSubscrAdminRowStatusThis variable is used to manage the creation and deletion
of conceptual rows in the bsciDevAdminTable and follows the
SNMPv2 RowStatus conventions by supporting the following values:
- `active', which indicates that the conceptual row is
available for use by the managed device. For a management
protocol set operation, a genErr response is returned when
the row does not exist.
- `createAndGo', which is supplied by a management
station wishing to create a new instance of a
conceptual row and to have its status automatically set
to active, making it available for use by the managed
device. For a management protocol set operation, a
genErr response is returned when the row already exists.
- `destroy', which is supplied by a management station
wishing to delete all of the instances associated with
an existing conceptual row.
Note that all of the above values may be specified in a
management protocol set operation, and only the 'active'
value will be returned in response to a management protocol
retrieval operation. For a management protocol set operation,
if other variable bindings are included in the same PDU, then
a genErr response is returned.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.173.7.3.4.3.1.8 |
bsciSubscrOperTableA list of BSC Interactive port subscribers. SEQUENCE OF BsciSubscrOperEntry .1.3.6.1.4.1.173.7.3.4.4 |
bsciSubscrOperEntryA BSCI Interactive Port Subscriber entry containing objects
relating to the port that are configurable by the user. BsciSubscrOperEntry .1.3.6.1.4.1.173.7.3.4.4.1 |
bsciSubscrOperSequenceSubscriber index for a specific BSCI port subscriber.ro INTEGER .1.3.6.1.4.1.173.7.3.4.4.1.1 |
bsciSubscrOperLocalIDSubscriber address of the local end of a BSCI connection.ro NlSubscriberAddress .1.3.6.1.4.1.173.7.3.4.4.1.2 |
bsciSubscrOperRemoteIDSubscriber address of the remote end of a BSCI connection.ro NlSubscriberAddress .1.3.6.1.4.1.173.7.3.4.4.1.3 |
bsciSubscrOperAutocallCauses a BSCI TPAD to automatically call its HPAD when
the controller becomes active.ro Enumeration .1.3.6.1.4.1.173.7.3.4.4.1.4 |
bsciSubscrOperAutocallRtyTimerTime between autocall retries.ro INTEGER .1.3.6.1.4.1.173.7.3.4.4.1.5 |
bsciSubscrOperAutocallMaxRtryMaximum number of times an autocall will be sent.ro INTEGER .1.3.6.1.4.1.173.7.3.4.4.1.6 |
bsciSubscrOperConnectionIDIdentifier that will link the BSCI port with a device
configured in the BSCI Devices Table.ro INTEGER .1.3.6.1.4.1.173.7.3.4.4.1.7 |
bsciDevAdminTableA list of BSC Interactive devices. SEQUENCE OF BsciDevAdminEntry .1.3.6.1.4.1.173.7.3.4.5 |
bsciDevAdminEntryA BSCI Interactive Device entry containing objects
relating to the device that are configurable by the user. BsciDevAdminEntry .1.3.6.1.4.1.173.7.3.4.5.1 |
bsciDevAdminControlUnitIDControl Unit identifier.ro INTEGER .1.3.6.1.4.1.173.7.3.4.5.1.1 |
bsciDevAdminDeviceUnitIDDevice Unit identifier.ro INTEGER .1.3.6.1.4.1.173.7.3.4.5.1.2 |
bsciDevAdminConnectionIDThe BSCI port connection ID for the device.rw INTEGER .1.3.6.1.4.1.173.7.3.4.5.1.3 |
bsciDevAdminSingleUserVCSpecifies whether each end of the connection is within
a same Control Unit/Device Type pair.rw Enumeration .1.3.6.1.4.1.173.7.3.4.5.1.4 |
bsciDevAdminTransTextSupportedCauses all characters transmitted to be treated as data.rw Enumeration .1.3.6.1.4.1.173.7.3.4.5.1.5 |
bsciDevAdminPrinterAttachedSpecifies whether the device has a printer attached.rw Enumeration .1.3.6.1.4.1.173.7.3.4.5.1.6 |
bsciDevAdminRowStatusThis variable is used to manage the creation and deletion
of conceptual rows in the bsciDevAdminTable and follows the
SNMPv2 RowStatus conventions by supporting the following values:
- `active', which indicates that the conceptual row is
available for use by the managed device. For a management
protocol set operation, a genErr response is returned when
the row does not exist.
- `createAndGo', which is supplied by a management
station wishing to create a new instance of a
conceptual row and to have its status automatically set
to active, making it available for use by the managed
device. For a management protocol set operation, a
genErr response is returned when the row already exists.
- `destroy', which is supplied by a management station
wishing to delete all of the instances associated with
an existing conceptual row.
Note that all of the above values may be specified in a
management protocol set operation, and only the 'active'
value will be returned in response to a management protocol
retrieval operation. For a management protocol set operation,
if other variable bindings are included in the same PDU, then
a genErr response is returned.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.173.7.3.4.5.1.7 |
bsciDevAdminDisableStatusRequestDetermines how the BSCI port will report the status
of the attached device. Normal status- the port will
report what the device reports. No status- the port will
report status only if the device is active. Always active
status- the port will always report the device as active.rw Enumeration .1.3.6.1.4.1.173.7.3.4.5.1.8 |
bsciDevOperTableA list of BSC Interactive devices. SEQUENCE OF BsciDevOperEntry .1.3.6.1.4.1.173.7.3.4.6 |
bsciDevOperEntryA BSCI Interactive Device entry containing objects
relating to the device that are configurable by the user. BsciDevOperEntry .1.3.6.1.4.1.173.7.3.4.6.1 |
bsciDevOperControlUnitIDControl Unit identifier.ro INTEGER .1.3.6.1.4.1.173.7.3.4.6.1.1 |
bsciDevOperDeviceUnitIDDevice Unit identifier.ro INTEGER .1.3.6.1.4.1.173.7.3.4.6.1.2 |
bsciDevOperConnectionIDThe BSCI port connection ID for the device.ro INTEGER .1.3.6.1.4.1.173.7.3.4.6.1.3 |
bsciDevOperSingleUserVCSpecifies whether each end of the connection is within
a same Control Unit/Device Type pair.ro Enumeration .1.3.6.1.4.1.173.7.3.4.6.1.4 |
bsciDevOperTransTextSupportedCauses all characters transmitted to be treated as data.ro Enumeration .1.3.6.1.4.1.173.7.3.4.6.1.5 |
bsciDevOperPrinterAttachedSpecifies whether the device has a printer attached.ro Enumeration .1.3.6.1.4.1.173.7.3.4.6.1.6 |
bsciDevOperDisableStatusRequestDetermines how the BSCI port will report the status
of the attached device. Normal status- the port will
report what the device reports. No status- the port will
report status only if the device is active. Always active
status- the port will always report the device as active.ro Enumeration .1.3.6.1.4.1.173.7.3.4.6.1.7 |
portSdlcGroup OBJECT IDENTIFIER .1.3.6.1.4.1.173.7.3.5 |
portSdlcAdminTableThis table contains Netlink Enterprise specific
objects to manage SDLC port. Changing on of the
these parameters may take effect in the operating
port immediately or may wait until the interface is restarted depending on the details of the
implementation.
Most of the objects in this read-write table have
corresponding read-only objects in the
portSdlcOperTable that return the current
operating value.
The operating values may be different from these
configured values if a configured parameter was
configured afterthe interface was started. SEQUENCE OF PortSdlcAdminEntry .1.3.6.1.4.1.173.7.3.5.1 |
portSdlcAdminEntryA list of configured values for an SDLC port. PortSdlcAdminEntry .1.3.6.1.4.1.173.7.3.5.1.1 |
portSdlcAdminCommitWriting a value to this object commits the
the SDLC port related modified configuration
values to the database.rwobsolete INTEGER .1.3.6.1.4.1.173.7.3.5.1.1.1 |
portSdlcAdminMAXRetriesThis object defines the max. number of retries
to a non-responding Link station, before putting
the Link station to slow-poll list if it is not
Normal response Mode OR disconnecting the link
station if it is data txfr state.rw INTEGER .1.3.6.1.4.1.173.7.3.5.1.1.2 |
portSdlcAdminMAXOutThis object defines the number of outstanding
frames for triggering window full condition.rw INTEGER .1.3.6.1.4.1.173.7.3.5.1.1.3 |
portSdlcAdminPadTypeThis object defines the SNA
PAD types.rw Enumeration .1.3.6.1.4.1.173.7.3.5.1.1.4 |
portSdlcAdminGenerateClockThis object defines if the port would
generate clock.rw Enumeration .1.3.6.1.4.1.173.7.3.5.1.1.5 |
portSdlcAdminRcvClockFromDTEThis object defines if the rcv clock will
be used from DTE.rw Enumeration .1.3.6.1.4.1.173.7.3.5.1.1.6 |
portSdlcAdminNrzThis object defines the data encoding
at the physical layerrw Enumeration .1.3.6.1.4.1.173.7.3.5.1.1.7 |
portSdlcAdminPacketSizeThis object defines the packet size of the
X25 layer used by SNA PADrw INTEGER .1.3.6.1.4.1.173.7.3.5.1.1.8 |
portSdlcAdminDisableRequestDisconnectThis object defines if a Request To
Disconnect(RD) will be sent when remote
PAD clear the connectionrw Enumeration .1.3.6.1.4.1.173.7.3.5.1.1.9 |
portSdlcAdminLPDASupportThis object defines the type LPDA support
on SDLC port.rw Enumeration .1.3.6.1.4.1.173.7.3.5.1.1.10 |
portSdlcAdminConnectorThis object defines the connector type
of the SDLC port.rw Enumeration .1.3.6.1.4.1.173.7.3.5.1.1.11 |
portSdlcAdminSpeedThis object defines the speed of the SDLC port. The speed may
only be set to one of a series of reasonable values, and if an attempt is made
to set the speed to a value which is within the valid range but not equal to one
of these values, the speed will be rounded up. If the connector type of the port
is RS232, the port could be a standard port or a high speed port. If the port is
a high speed RS232 port, the maximum valid speed is 256000. If the port is a standard
RS232 port, the maximum valid speed is 64000 on the FRX4000/SS1840 and 19200
on all other products. It may be possible to set the speed of a standard RS232 port
to a speed which is valid for a high speed RS232 port but invalid for a standard
RS232 port. In this case, the port may not end up having the invalid speed. The default
speed for a standard RS232 port on the FRX6000 is 19200.rw INTEGER .1.3.6.1.4.1.173.7.3.5.1.1.12 |
portSdlcAdminRowStatusThis variable is used to manage the creation and deletion
of conceptual rows in the portSdlcAdminTable and follows the
SNMPv2 RowStatus conventions by supporting the following values:
- `active', which indicates that the conceptual row is
available for use by the managed device, and which is
supplied by a management station wishing to exercise an
on-line update of the existing conceptual row. For a
management protocol set operation, a genErr response is
returned when the row does not exist.
- `createAndGo', which is supplied by a management
station wishing to create a new instance of a
conceptual row and to have its status automatically set
to active, making it available for use by the managed
device. For a management protocol set operation, a
genErr response is returned when the row already exists.
- `destroy', which is supplied by a management station
wishing to delete all of the instances associated with
an existing conceptual row.
Note that all of the above values may be specified in a
management protocol set operation, and only the 'active'
value will be returned in response to a management protocol
retrieval operation. For a management protocol set operation,
if other variable bindings are included in the same PDU, then
a genErr response is returned.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.173.7.3.5.1.1.13 |
portSdlcAdminIdleFillCharThis object specifies a character that
wll be inserted into the stream when the
SNA link is idle.rw Enumeration .1.3.6.1.4.1.173.7.3.5.1.1.14 |
portSdlcAdminInactivityTimerThis object determines how long the node
will wait with no activity on the port
before it will declare the attached device
down.rw INTEGER .1.3.6.1.4.1.173.7.3.5.1.1.15 |
portSdlcAdminL1DuplexThis object determines whether level-1
(physical layer) transmission can be in
one (half duplex) or both (full duplex)
directions at once.rw Enumeration .1.3.6.1.4.1.173.7.3.5.1.1.16 |
portSdlcOperTableThis table contains current Netlink enterprise specific
port parameters SEQUENCE OF PortSdlcOperEntry .1.3.6.1.4.1.173.7.3.5.2 |
portSdlcOperEntryA list of operational values for an SDLC port. PortSdlcOperEntry .1.3.6.1.4.1.173.7.3.5.2.1 |
portSdlcOperCommitThis object is not used.roobsolete INTEGER .1.3.6.1.4.1.173.7.3.5.2.1.1 |
portSdlcOperMAXRetriesThis object defines the max. number of retries
to a non-responding Link station, before putting
the Link station to slow-poll list if it is not
Normal response Mode OR disconnecting the link
station if it is data txfr state.ro INTEGER .1.3.6.1.4.1.173.7.3.5.2.1.2 |
portSdlcOperMAXOutThis object defines the number of outstanding
frames for triggering window full condition.ro INTEGER .1.3.6.1.4.1.173.7.3.5.2.1.3 |
portSdlcOperPadTypeThis object defines the SNA
PAD typero Enumeration .1.3.6.1.4.1.173.7.3.5.2.1.4 |
portSdlcOperGenerateClockThis object defines if the port would
generate clock.ro Enumeration .1.3.6.1.4.1.173.7.3.5.2.1.5 |
portSdlcOperRcvClockFromDTEThis object defines if the rcv clock will
be used from DTE.ro Enumeration .1.3.6.1.4.1.173.7.3.5.2.1.6 |
portSdlcOperNrzThis object defines the data encoding
at the physical layerro Enumeration .1.3.6.1.4.1.173.7.3.5.2.1.7 |
portSdlcOperPacketSizeThis object defines the packet size of the
X25 layer used by SNA PADro INTEGER .1.3.6.1.4.1.173.7.3.5.2.1.8 |
portSdlcOperDisableRequestDisconnectThis object defines if a Request To
Disconnect(RD) will be sent when remote
PAD clear the connectionro Enumeration .1.3.6.1.4.1.173.7.3.5.2.1.9 |
portSdlcOperLPDASupportThis object defines the type LPDA support
on SDLC port.ro Enumeration .1.3.6.1.4.1.173.7.3.5.2.1.10 |
portSdlcOperConnectorThis object defines the operational
connector type of the SDLC port.ro Enumeration .1.3.6.1.4.1.173.7.3.5.2.1.11 |
portSdlcOperSpeedThis object defines the operational speed
of the SDLC port.ro INTEGER .1.3.6.1.4.1.173.7.3.5.2.1.12 |
portSdlcOperIdleFillCharThis object specifies a character that
wll be inserted into the stream when the
SNA link is idle.ro Enumeration .1.3.6.1.4.1.173.7.3.5.2.1.13 |
portSdlcOperInactivityTimerThis object determines how long the node
will wait with no activity on the port
before it will declare the attached device
down.ro INTEGER .1.3.6.1.4.1.173.7.3.5.2.1.14 |
portSdlcOperL1DuplexThis object determines whether level-1
(physical layer) transmission can be in
one (half duplex) or both (full duplex)
directions at once.ro Enumeration .1.3.6.1.4.1.173.7.3.5.2.1.15 |
lSSdlcAdminTableThis table contains Enterprise specific Link station
configurable parameters to manage the link stations. SEQUENCE OF LSSdlcAdminEntry .1.3.6.1.4.1.173.7.3.5.3 |
lSSdlcAdminEntryA list of configured values for an SDLC port. LSSdlcAdminEntry .1.3.6.1.4.1.173.7.3.5.3.1 |
lSSdlcAdminLocalSubThis object defines the local subscriber ID
of the Link Stationrw NlSubscriberAddress .1.3.6.1.4.1.173.7.3.5.3.1.1 |
lSSdlcAdminRemoteSubThis object defines the remote subscriber ID
used to connect to remote Link Stationrw NlSubscriberAddress .1.3.6.1.4.1.173.7.3.5.3.1.2 |
lSSdlcAdminAutoCallThis object defines if auto call is enabled for
the link station. If enabled, the link station
will initiate connection establishment, when
appropriate. Else, it will passively listen to
the connection request for establish a connection
with the remote PADrw Enumeration .1.3.6.1.4.1.173.7.3.5.3.1.3 |
lSSdlcAdminRetryTimeThis object is used, only when
lSSdlcAdminAutoCall object is yes. This defines
the time interval measured in seconds in which
the connection request is retriedrw INTEGER .1.3.6.1.4.1.173.7.3.5.3.1.4 |
lSSdlcAdminRetryCountThis object is used, only when
lSSdlcAdminAutoCall object is yes. This defines
the number of times the connection initiation
is retried before given up. The value of Zero(0)
means to try indefinitelyrw INTEGER .1.3.6.1.4.1.173.7.3.5.3.1.5 |
lSSdlcAdminLlc2ConversionThis object defines if this link station
connects to a LLC2 device/host.rw Enumeration .1.3.6.1.4.1.173.7.3.5.3.1.6 |
lSSdlcAdminLPDAResourceIDThis objects the resource ID used during
LPDA command supportrw INTEGER .1.3.6.1.4.1.173.7.3.5.3.1.7 |
lSSdlcAdminRowStatusThis variable is used to manage the creation and deletion
of conceptual rows in the lSSdlcAdminTable and follows the
SNMPv2 RowStatus conventions by supporting the following values:
- `active', which indicates that the conceptual row is
available for use by the managed device. For a management
protocol set operation, a genErr response is returned when
the row does not exist.
- `createAndGo', which is supplied by a management
station wishing to create a new instance of a
conceptual row and to have its status automatically set
to active, making it available for use by the managed
device. For a management protocol set operation, a
genErr response is returned when the row already exists.
- `destroy', which is supplied by a management station
wishing to delete all of the instances associated with
an existing conceptual row.
Note that all of the above values may be specified in a
management protocol set operation, and only the 'active'
value will be returned in response to a management protocol
retrieval operation. For a management protocol set operation,
if other variable bindings are included in the same PDU, then
a genErr response is returned.
Also note that deleting a PU entry will only remove it from
the database file, and it's existence will still be known by
the protocol until the node is rebooted or until an online
update of the port is performed.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.173.7.3.5.3.1.8 |
lSSdlcAdminL2DatModeThis object determines whether transmission
can be in one (alternate) or two (simultaneous)
directions at the same time.rw Enumeration .1.3.6.1.4.1.173.7.3.5.3.1.9 |
lSSdlcOperTableThis table contains the operational parameters of the
SDLC port SEQUENCE OF LSSdlcOperEntry .1.3.6.1.4.1.173.7.3.5.4 |
lSSdlcOperEntryA list of configured values for an SDLC port. LSSdlcOperEntry .1.3.6.1.4.1.173.7.3.5.4.1 |
lSSdlcOperLocalSubThis object defines the local subscriber ID
of the Link Stationro NlSubscriberAddress .1.3.6.1.4.1.173.7.3.5.4.1.1 |
lSSdlcOperRemoteSubThis object defines the remote subscriber ID
used to connect to remote Link Stationro NlSubscriberAddress .1.3.6.1.4.1.173.7.3.5.4.1.2 |
lSSdlcOperAutoCallThis object defines if auto call is enabled for
the link station. If enabled, the link station
will initiate connection establishment, when
appropriate. Else, it will passively listen to
the connection request for establish a connection
with the remote PADro Enumeration .1.3.6.1.4.1.173.7.3.5.4.1.3 |
lSSdlcOperRetryTimeThis object is valid, only when
lSSdlcAdminAutoCall object is yes. This defines
the time interval measured in seconds in which
the connection request is retriedro INTEGER .1.3.6.1.4.1.173.7.3.5.4.1.4 |
lSSdlcOperRetryCountThis object is used, only when
lSSdlcAdminAutoCall object is yes. This defines
the number of times the connection initiation
is retried before given up. The value of Zero(0)
means to try indefinitelyro INTEGER .1.3.6.1.4.1.173.7.3.5.4.1.5 |
lSSdlcOperLlc2ConversionThis object defines if this link station
connects to a LLC2 device/host.ro Enumeration .1.3.6.1.4.1.173.7.3.5.4.1.6 |
lSSdlcOperLPDAResourceIDThis objects the resource ID used during
LPDA command supportro INTEGER .1.3.6.1.4.1.173.7.3.5.4.1.7 |
lSSdlcOperL2DatModeThis object determines whether transmission
can be in one (alternate) or two (simultaneous)
directions at the same time.ro Enumeration .1.3.6.1.4.1.173.7.3.5.4.1.8 |
lSSdlcLlc2AdminTableThis table contains the LLC2 related parameters
used to configure LLC2 session, when the SDLC
station is connected to a LLC2 device at the remote
end SEQUENCE OF LSSdlcLlc2AdminEntry .1.3.6.1.4.1.173.7.3.5.5 |
lSSdlcLlc2AdminEntryA list of configured values for an SDLC port. LSSdlcLlc2AdminEntry .1.3.6.1.4.1.173.7.3.5.5.1 |
lSSdlcLlc2AdminLocalSapThis object defines Local SAP
address (multiple of 4)rw INTEGER .1.3.6.1.4.1.173.7.3.5.5.1.1 |
lSSdlcLlc2AdminLocalMacThis object defines the local MAC addressrw PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.173.7.3.5.5.1.2 |
lSSdlcLlc2AdminIdblkThis object defines idblk used in XIDrw INTEGER .1.3.6.1.4.1.173.7.3.5.5.1.3 |
lSSdlcLlc2AdminIdnumThis object defines idnum used in XIDrw INTEGER .1.3.6.1.4.1.173.7.3.5.5.1.4 |
lSSdlcLlc2AdminLanTiThis object defines LLC2 inactivity timer
measured in units of secondsrw INTEGER .1.3.6.1.4.1.173.7.3.5.5.1.5 |
lSSdlcLlc2AdminLanT1This object defines LLC2 reply timer
measured in units of 100 millisecondsrw INTEGER .1.3.6.1.4.1.173.7.3.5.5.1.6 |
lSSdlcLlc2AdminLanT2This object defines Receiver Ack Timer
measured in units of millisecondsrw INTEGER .1.3.6.1.4.1.173.7.3.5.5.1.7 |
lSSdlcLlc2AdminLanN2This object defines Maximum Retransmissionsrw INTEGER .1.3.6.1.4.1.173.7.3.5.5.1.8 |
lSSdlcLlc2AdminLanN3This object defines count of I-format LPDU's
before sending Ackrw INTEGER .1.3.6.1.4.1.173.7.3.5.5.1.9 |
lSSdlcLlc2AdminLanTwThis object defines Outstanding Framesrw INTEGER .1.3.6.1.4.1.173.7.3.5.5.1.10 |
lSSdlcLlc2AdminBAGThis object defines bandwidth allocation
grouprw INTEGER .1.3.6.1.4.1.173.7.3.5.5.1.11 |
lSSdlcLlc2AdminPriorityThis object defines priority for traffic
within the noderw INTEGER .1.3.6.1.4.1.173.7.3.5.5.1.12 |
lSSdlcLlc2AdminRowStatusThis variable is used to manage the creation and deletion
of conceptual rows in the lSSdlcLlc2AdminTable and follows the
SNMPv2 RowStatus conventions by supporting the following values:
- `active', which indicates that the conceptual row is
available for use by the managed device. For a management
protocol set operation, a genErr response is returned when
the row does not exist.
- `createAndGo', which is supplied by a management
station wishing to create a new instance of a
conceptual row and to have its status automatically set
to active, making it available for use by the managed
device. For a management protocol set operation, a
genErr response is returned when the row already exists.
- `destroy', which is supplied by a management station
wishing to delete all of the instances associated with
an existing conceptual row.
Note that all of the above values may be specified in a
management protocol set operation, and only the 'active'
value will be returned in response to a management protocol
retrieval operation. For a management protocol set operation,
if other variable bindings are included in the same PDU, then
a genErr response is returned.
Also note that deleting a PU entry will only remove it from
the database file, and it's existence will still be known by
the protocol until the node is rebooted or until an online
update of the port is performed.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.173.7.3.5.5.1.13 |
lSSdlcLlc2AdminSuppressXIDThis object prevents (if yes) the returning
of an XID in response to a null XID. This
might be desirable if the remote TPAD is not
running PU 2.1. It should be noted that even
if an XID is sent, an SNRM (Set Normal
Response Mode) immediately follows, so the
connection will be established.rw Enumeration .1.3.6.1.4.1.173.7.3.5.5.1.14 |
lSSdlcLlc2OperTableThis table contains operartional parameters related
to LLC2 session of this link station. SEQUENCE OF LSSdlcLlc2OperEntry .1.3.6.1.4.1.173.7.3.5.6 |
lSSdlcLlc2OperEntryA list of configured values for an SDLC port. LSSdlcLlc2OperEntry .1.3.6.1.4.1.173.7.3.5.6.1 |
lSSdlcLlc2OperLocalSapThis object defines Local SAP
address (multiple of 4)ro INTEGER .1.3.6.1.4.1.173.7.3.5.6.1.1 |
lSSdlcLlc2OperLocalMacThis object defines the local MAC addressro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.173.7.3.5.6.1.2 |
lSSdlcLlc2OperIdblkThis object defines idblk used in XIDro INTEGER .1.3.6.1.4.1.173.7.3.5.6.1.3 |
lSSdlcLlc2OperIdnumThis object defines idnum used in XIDro INTEGER .1.3.6.1.4.1.173.7.3.5.6.1.4 |
lSSdlcLlc2OperLanTiThis object defines LLC2 inactivity timer
measured in units of secondsro INTEGER .1.3.6.1.4.1.173.7.3.5.6.1.5 |
lSSdlcLlc2OperLanT1This object defines LLC2 reply timer
measured in units of 100 millisecondsro INTEGER .1.3.6.1.4.1.173.7.3.5.6.1.6 |
lSSdlcLlc2OperLanT2This object defines Receiver Ack Timer
measured in units of millisecondsro INTEGER .1.3.6.1.4.1.173.7.3.5.6.1.7 |
lSSdlcLlc2OperLanN2This object defines Maximum Retransmissionsro INTEGER .1.3.6.1.4.1.173.7.3.5.6.1.8 |
lSSdlcLlc2OperLanN3This object defines count of I-format LPDU's
before sending Ackro INTEGER .1.3.6.1.4.1.173.7.3.5.6.1.9 |
lSSdlcLlc2OperLanTwThis object defines Outstanding Framesro INTEGER .1.3.6.1.4.1.173.7.3.5.6.1.10 |
lSSdlcLlc2OperBAGThis object defines bandwidth allocation
groupro INTEGER .1.3.6.1.4.1.173.7.3.5.6.1.11 |
lSSdlcLlc2OperPriorityThis object defines priority for traffic
within the nodero INTEGER .1.3.6.1.4.1.173.7.3.5.6.1.12 |
lSSdlcLlc2OperSuppressXIDThis object prevents (if yes) the returning
of an XID in response to a null XID. This
might be desirable if the remote TPAD is not
running PU 2.1. It should be noted that even
if an XID is sent, an SNRM (Set Normal
Response Mode) immediately follows, so the
connection will be established.ro Enumeration .1.3.6.1.4.1.173.7.3.5.6.1.13 |
portT1Group OBJECT IDENTIFIER .1.3.6.1.4.1.173.7.3.7 |
portT1AdminTableThe configuration information pertaining to a T1 port.
T1 ports can operate at full T1 bandwidth or DS0A channelized which provides
24 separate channels. SEQUENCE OF PortT1AdminEntry .1.3.6.1.4.1.173.7.3.7.1 |
portT1AdminEntryA T1 port entry containing objects relating to T1 ports. PortT1AdminEntry .1.3.6.1.4.1.173.7.3.7.1.1 |
portT1AdminBlockedPortFlagrw Enumeration .1.3.6.1.4.1.173.7.3.7.1.1.1 |
portT1AdminGenerateClockrw Enumeration .1.3.6.1.4.1.173.7.3.7.1.1.2 |
portT1AdminFramingModeSpecifies how this T1 port is to function. ds0AT1 specifies a
24 channelized T1.rw Enumeration .1.3.6.1.4.1.173.7.3.7.1.1.3 |
portT1AdminFrameModelSelectrw Enumeration .1.3.6.1.4.1.173.7.3.7.1.1.4 |
portT1AdminLineEncodingrw Enumeration .1.3.6.1.4.1.173.7.3.7.1.1.5 |
portT1AdminLineBuildOutrw Enumeration .1.3.6.1.4.1.173.7.3.7.1.1.6 |
portT1AdminRowStatusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.173.7.3.7.1.1.7 |
portT1AdminProtocolFramingrw Enumeration .1.3.6.1.4.1.173.7.3.7.1.1.8 |
portT1AdminNRZIrw Enumeration .1.3.6.1.4.1.173.7.3.7.1.1.9 |
portT1OperTableThe configuration information pertaining to a T1 port.
T1 ports can operate at full T1 bandwidth or DS0A channelized which provides
24 separate channels. SEQUENCE OF PortT1OperEntry .1.3.6.1.4.1.173.7.3.7.2 |
portT1OperEntryA T1 port entry containing objects relating to T1 ports. PortT1OperEntry .1.3.6.1.4.1.173.7.3.7.2.1 |
portT1OperBlockedPortFlagro Enumeration .1.3.6.1.4.1.173.7.3.7.2.1.1 |
portT1OperGenerateClockro Enumeration .1.3.6.1.4.1.173.7.3.7.2.1.2 |
portT1OperFramingModeSpecifies how this T1 port is to function. ds0AT1 specifies a
24 channelized T1.ro Enumeration .1.3.6.1.4.1.173.7.3.7.2.1.3 |
portT1OperFrameModelSelectro Enumeration .1.3.6.1.4.1.173.7.3.7.2.1.4 |
portT1OperLineEncodingro Enumeration .1.3.6.1.4.1.173.7.3.7.2.1.5 |
portT1OperLineBuildOutro Enumeration .1.3.6.1.4.1.173.7.3.7.2.1.6 |
portT1OperProtocolFramingro Enumeration .1.3.6.1.4.1.173.7.3.7.2.1.7 |
portT1OperNRZIro Enumeration .1.3.6.1.4.1.173.7.3.7.2.1.8 |
portVoiceGroup OBJECT IDENTIFIER .1.3.6.1.4.1.173.7.3.8 |
portVoiceAdminTableA list of Voice ports. The number of entries
will be the number of Voice ports on the node. SEQUENCE OF PortVoiceAdminEntry .1.3.6.1.4.1.173.7.3.8.1 |
portVoiceAdminEntryA Voice Port entry containing objects relating
to the port that are configurable by the user. PortVoiceAdminEntry .1.3.6.1.4.1.173.7.3.8.1.1 |
portVoiceAdminRlpIndexThe RLP number of the Voice port.ro INTEGER .1.3.6.1.4.1.173.7.3.8.1.1.1 |
portVoiceAdminPortIndexThe Port number of the Voice port.ro INTEGER .1.3.6.1.4.1.173.7.3.8.1.1.2 |
portVoiceAdminBlockedFlagThe flag which causes the port to be enabled or disabled
at node IPL. The port will remain in that state until this
flag is changed and the node is rebooted, or until an on-
line enable or disable is performed.rw Enumeration .1.3.6.1.4.1.173.7.3.8.1.1.3 |
portVoiceAdminSpeedThe speed of the port which is transmitted as part
of a Call Setup frame. A Voice call will be established
if there is enough bandwidth at each end to provide the
minimum configured rate.rw Enumeration .1.3.6.1.4.1.173.7.3.8.1.1.4 |
portVoiceAdminDTMFThe flag to enable, disable, or specify a time span
over which DTMF (Dual Tone Multi Frequency) tones will
be regenerated.
0 = pass tones transparently to the remote device.
1 = detect incoming tones and regenerate as received.
2-255 = regenerate tones for the specified seconds.rw INTEGER .1.3.6.1.4.1.173.7.3.8.1.1.5 |
portVoiceAdminInterfaceThe type of interface (in conjunction with the Telephony
Interface Type) that will be used by the Voice channel.
This requires rebooting for the change to take effect.
Telephony Type Interface Type
OPX (FXO) Loop Start
SLT (FXS) Loop Start
E&M 4W E&M, 4W E&M TE, 2W E&M, 2W E&M TE
AC15 AC15A, AC15Crw Enumeration .1.3.6.1.4.1.173.7.3.8.1.1.6 |
portVoiceAdminTETimerThe delay at which the E&M 'E' lead follows the 'M' lead.rw INTEGER .1.3.6.1.4.1.173.7.3.8.1.1.7 |
portVoiceAdminLevelInThe local voice level into the voice port. This adjusts
the sensitivity of the local voice channel to the signal
from the attached device. The purpose of this is to match
the voice channel dB level to the input signal. A more
negative setting produces a higher input gain. If the level
is reduced, the voice channel will be more sensitive to the
input. This will also cause the voice output at the remote
device to sound louder.rw INTEGER (-22..7) .1.3.6.1.4.1.173.7.3.8.1.1.8 |
portVoiceAdminLevelOutThe local voice level out of the voice port. A more
positive setting produces a higher volume.rw INTEGER (-22..7) .1.3.6.1.4.1.173.7.3.8.1.1.9 |
portVoiceAdminCallTimerThe amount of time the node will wait for a response to a
Call Connect or Call Clear request. When the node issues a
request, it will set a timer to the value configured here.
If that timer expires with no response from the destination,
the node will generate a busy tone.rw INTEGER .1.3.6.1.4.1.173.7.3.8.1.1.10 |
portVoiceAdminHuntGroupThe hunt group that includes the voice channel.rw Enumeration .1.3.6.1.4.1.173.7.3.8.1.1.11 |
portVoiceAdminLongDialPrefixThe character that will be required preceeding calls using
the long call format. When the user at an attached device
dials a long form number, it must be preceeded by the prefix
character specified here.rw OCTET STRING .1.3.6.1.4.1.173.7.3.8.1.1.12 |
portVoiceAdminSLTTimeoutThe time the local port will wait before an actual fax
transmission begins. If there is no fax tone when this
timer expires, the connection will be terminated.rw INTEGER .1.3.6.1.4.1.173.7.3.8.1.1.13 |
portVoiceAdminLinkDownBusyThis flag enables or disables automatic busy-out of
channels when the link is down. When enabled, the system
will automatically busy-out channels when the composite
link is down. When disabled, channels remain on-hook when
the link is down. If your application is connected to a
PBX that can route calls to another alternate source based
on an all busy condition, enable this so the PBX will
recognize this condition and reroute the calls while the
composite link is down.rw Enumeration .1.3.6.1.4.1.173.7.3.8.1.1.14 |
portVoiceAdminFaxSupportedThe flag to indicate whether or not faxes will be
transmitted on the port. If no, all calls will be treated
as voice. If yes, both voice and fax will be transmitted.rw Enumeration .1.3.6.1.4.1.173.7.3.8.1.1.15 |
portVoiceAdminTelephonyTypeThe type of interface (in conjunction with the
Interface Type) that will be used by the Voice channel.
This requires rebooting for the change to take effect.
Telephony Type Interface Type
OPX (FXO) Loop Start
SLT (FXS) Loop Start
E&M 4W E&M, 4W E&M TE, 2W E&M, 2W E&M TE
AC15 AC15A, AC15Crw Enumeration .1.3.6.1.4.1.173.7.3.8.1.1.16 |
portVoiceAdminJitterThe amount of jitter delay.rw INTEGER .1.3.6.1.4.1.173.7.3.8.1.1.17 |
portVoiceAdminSampleDelayThe amount of sample delay.rw INTEGER .1.3.6.1.4.1.173.7.3.8.1.1.18 |
portVoiceAdminDialTimerThe delay the node will use to determine when variable
length dialing is complete. (Variable length dialing allows
the user to place a call without entering the configured
number of digits for the speed dial number.)rw INTEGER .1.3.6.1.4.1.173.7.3.8.1.1.19 |
portVoiceAdminAutoDialThe flag to enable or disable the auto dial feature. Note
that enabling this feature will disable the variable length
dialing feature for this channel.rw Enumeration .1.3.6.1.4.1.173.7.3.8.1.1.20 |
portVoiceAdminSuppressionThe silence suppression level. A larger silence suppression
level allows more data channels to operate simultaneously
with the voice channels.rw Enumeration .1.3.6.1.4.1.173.7.3.8.1.1.21 |
portVoiceAdminAutoDialNumberThe number to which the node will attempt to connect when
the handset attached to this port is taken off-hook. This
is applicable only when the Auto Dial feature is enabled.rw OCTET STRING .1.3.6.1.4.1.173.7.3.8.1.1.22 |
portVoiceAdminAutoPollThe flag to enable or disable auto polling. This is
applicable only when the Auto Dial feature is enabled.
When enabled, the node periodically polls the destination.
If the poll is not acknowledged, the node will busy-out
the channel. This can be useful in situations where the
destination is an emergency number that must always be
available. If the destination does not answer the automatic
poll, the busy-out condition will notify an attached PBX
that the emergency call should be routed to another call
routing device.rw Enumeration .1.3.6.1.4.1.173.7.3.8.1.1.23 |
portVoiceAdminAutoPollTimerThe frequency with which an Auto Poll will be sent. This
is applicable only when auto poll is enabled.rw INTEGER .1.3.6.1.4.1.173.7.3.8.1.1.24 |
portVoiceAdminExtDigitsSourceThe source of the extended digits when the user of
attached equipment dials a speed dial number. This is
applicable only when the number of extended dial digits
is greater than zero. When map is specified, extended
digits are taken from the extended digits field in the
map table. When user is specified, extended digits are
taken from the user of attached equipment.rw Enumeration .1.3.6.1.4.1.173.7.3.8.1.1.25 |
portVoiceAdminNumDigitsDeleteThe number of leading dial digits that will be deleted
before a dial string is forwarded. This is primarily used
to delete leading dial digits that may be inserted by an
attached PBX.rw INTEGER .1.3.6.1.4.1.173.7.3.8.1.1.26 |
portVoiceAdminForwardDelayThe length of a pause that can be inserted in an extended
dial string that is being forwarded. This is applicable only
when forwarded output digits is all or extended. When a comma
is encountered in an extended digits string, the node will
pause for the length of time specified here before additional
extended digits are forwarded.rw INTEGER .1.3.6.1.4.1.173.7.3.8.1.1.27 |
portVoiceAdminForwardedTypeThe method how the dial digits will be forwarded. This
is applicable only when forwarded output digits is all
or extended.rw Enumeration .1.3.6.1.4.1.173.7.3.8.1.1.28 |
portVoiceAdminForwardedDigitsThe flag indicating which dial digits, if any, to forward.
If none, dial digits are not forwarded to the destination
device when a call is initiated on this channel. If all,
the dialed speed dial number and associated extended digits
are forwarded to the destination device. If extended, only
the extended digit string is forwarded.rw Enumeration .1.3.6.1.4.1.173.7.3.8.1.1.29 |
portVoiceAdminMakeRatioThe make ratio of each digit pulse that is forwarded.
This is applicable only when forwarded output digits
is all or extended and forwarded digit type is pulse.rw INTEGER .1.3.6.1.4.1.173.7.3.8.1.1.30 |
portVoiceAdminBreakRatioThe break ratio of each digit pulse that is forwarded.
This is applicable only when forwarded output digits
is all or extended and forwarded digit type is pulse.rw INTEGER .1.3.6.1.4.1.173.7.3.8.1.1.31 |
portVoiceAdminDTMFOnDurationThe length of a tone that will be used to produce a
single DTMF digit. This is applicable only when forwarded
output digits is all or extended and forwarded digit type
is DTMF.rw INTEGER .1.3.6.1.4.1.173.7.3.8.1.1.32 |
portVoiceAdminDTMFOffDurationThe length of silence between DTMF tones in a dial digit
string. This is applicable only when forwarded output digits
is all or extended and forwarded digit type is DTMF.rw INTEGER .1.3.6.1.4.1.173.7.3.8.1.1.33 |
portVoiceAdminToneTypeThe tone type to detect/regenerate for forwarding DTMF/MF.rw Enumeration .1.3.6.1.4.1.173.7.3.8.1.1.34 |
portVoiceAdminRowStatusThis variable is used to manage the creation and deletion
of conceptual rows in the portVoiceAdminTable and follows the
SNMPv2 RowStatus conventions by supporting the following values:
- `active', which indicates that the conceptual row is
available for use by the managed device, and which is
supplied by a management station wishing to exercise an
on-line update of the existing conceptual row. For a
management protocol set operation, a genErr response is
returned when the row does not exist.
- `createAndGo', which is supplied by a management
station wishing to create a new instance of a
conceptual row and to have its status automatically set
to active, making it available for use by the managed
device. For a management protocol set operation, a
genErr response is returned when the row already exists.
- `destroy', which is supplied by a management station
wishing to delete all of the instances associated with
an existing conceptual row.
Note that all of the above values may be specified in a
management protocol set operation, and only the 'active'
value will be returned in response to a management protocol
retrieval operation. For a management protocol set operation,
if other variable bindings are included in the same PDU, then
a genErr response is returned.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.173.7.3.8.1.1.35 |
portVoiceOperTableA list of Voice ports. The number of entries
will be the number of Voice ports on the node. SEQUENCE OF PortVoiceOperEntry .1.3.6.1.4.1.173.7.3.8.2 |
portVoiceOperEntryA Voice Port entry containing objects relating
to the port that are configurable by the user. PortVoiceOperEntry .1.3.6.1.4.1.173.7.3.8.2.1 |
portVoiceOperRlpIndexThe RLP number of the Voice port.ro INTEGER .1.3.6.1.4.1.173.7.3.8.2.1.1 |
portVoiceOperPortIndexThe Port number of the Voice port.ro INTEGER .1.3.6.1.4.1.173.7.3.8.2.1.2 |
portVoiceOperBlockedFlagThe flag which causes the port to be enabled or disabled
at node IPL. The port will remain in that state until this
flag is changed and the node is rebooted, or until an on-
line enable or disable is performed.ro Enumeration .1.3.6.1.4.1.173.7.3.8.2.1.3 |
portVoiceOperSpeedThe speed of the port which is transmitted as part
of a Call Setup frame. A Voice call will be established
if there is enough bandwidth at each end to provide the
minimum configured rate.ro Enumeration .1.3.6.1.4.1.173.7.3.8.2.1.4 |
portVoiceOperDTMFThe flag to enable, disable, or specify a time span
over which DTMF (Dual Tone Multi Frequency) tones will
be regenerated.
0 = pass tones transparently to the remote device.
1 = detect incoming tones and regenerate as received.
2-255 = regenerate tones for the specified seconds.ro INTEGER .1.3.6.1.4.1.173.7.3.8.2.1.5 |
portVoiceOperInterfaceThe type of interface (in conjunction with the Telephony
Interface Type) that will be used by the Voice channel.
This requires rebooting for the change to take effect.
Telephony Type Interface Type
OPX (FXO) Loop Start
SLT (FXS) Loop Start
E&M 4W E&M, 4W E&M TE, 2W E&M, 2W E&M TE
AC15 AC15A, AC15Cro Enumeration .1.3.6.1.4.1.173.7.3.8.2.1.6 |
portVoiceOperTETimerThe delay at which the E&M 'E' lead follows the 'M' lead.ro INTEGER .1.3.6.1.4.1.173.7.3.8.2.1.7 |
portVoiceOperLevelInThe local voice level into the voice port. This adjusts
the sensitivity of the local voice channel to the signal
from the attached device. The purpose of this is to match
the voice channel dB level to the input signal. A more
negative setting produces a higher input gain. If the level
is reduced, the voice channel will be more sensitive to the
input. This will also cause the voice output at the remote
device to sound louder.ro INTEGER (-22..7) .1.3.6.1.4.1.173.7.3.8.2.1.8 |
portVoiceOperLevelOutThe local voice level out of the voice port. A more
positive setting produces a higher volume.ro INTEGER (-22..7) .1.3.6.1.4.1.173.7.3.8.2.1.9 |
portVoiceOperCallTimerThe amount of time the node will wait for a response to a
Call Connect or Call Clear request. When the node issues a
request, it will set a timer to the value configured here.
If that timer expires with no response from the destination,
the node will generate a busy tone.ro INTEGER .1.3.6.1.4.1.173.7.3.8.2.1.10 |
portVoiceOperHuntGroupThe hunt group that includes the voice channel.ro Enumeration .1.3.6.1.4.1.173.7.3.8.2.1.11 |
portVoiceOperLongDialPrefixThe character that will be required preceeding calls using
the long call format. When the user at an attached device
dials a long form number, it must be preceeded by the prefix
character specified here.ro OCTET STRING .1.3.6.1.4.1.173.7.3.8.2.1.12 |
portVoiceOperSLTTimeoutThe time the local port will wait before an actual fax
transmission begins. If there is no fax tone when this
timer expires, the connection will be terminated.ro INTEGER .1.3.6.1.4.1.173.7.3.8.2.1.13 |
portVoiceOperLinkDownBusyThis flag enables or disables automatic busy-out of
channels when the link is down. When enabled, the system
will automatically busy-out channels when the composite
link is down. When disabled, channels remain on-hook when
the link is down. If your application is connected to a
PBX that can route calls to another alternate source based
on an all busy condition, enable this so the PBX will
recognize this condition and reroute the calls while the
composite link is down.ro Enumeration .1.3.6.1.4.1.173.7.3.8.2.1.14 |
portVoiceOperFaxSupportedThe flag to indicate whether or not faxes will be
transmitted on the port. If no, all calls will be treated
as voice. If yes, both voice and fax will be transmitted.ro Enumeration .1.3.6.1.4.1.173.7.3.8.2.1.15 |
portVoiceOperTelephonyTypeThe type of interface (in conjunction with the
Interface Type) that will be used by the Voice channel.
This requires rebooting for the change to take effect.
Telephony Type Interface Type
OPX (FXO) Loop Start
SLT (FXS) Loop Start
E&M 4W E&M, 4W E&M TE, 2W E&M, 2W E&M TE
AC15 AC15A, AC15Cro Enumeration .1.3.6.1.4.1.173.7.3.8.2.1.16 |
portVoiceOperJitterThe amount of jitter delay.ro INTEGER .1.3.6.1.4.1.173.7.3.8.2.1.17 |
portVoiceOperSampleDelayThe amount of sample delay.ro INTEGER .1.3.6.1.4.1.173.7.3.8.2.1.18 |
portVoiceOperDialTimerThe delay the node will use to determine when variable
length dialing is complete. (Variable length dialing allows
the user to place a call without entering the configured
number of digits for the speed dial number.)ro INTEGER .1.3.6.1.4.1.173.7.3.8.2.1.19 |
portVoiceOperAutoDialThe flag to enable or disable the auto dial feature. Note
that enabling this feature will disable the variable length
dialing feature for this channel.ro Enumeration .1.3.6.1.4.1.173.7.3.8.2.1.20 |
portVoiceOperSuppressionThe silence suppression level. A larger silence suppression
level allows more data channels to operate simultaneously
with the voice channels.ro Enumeration .1.3.6.1.4.1.173.7.3.8.2.1.21 |
portVoiceOperAutoDialNumberThe number to which the node will attempt to connect when
the handset attached to this port is taken off-hook. This
is applicable only when the Auto Dial feature is enabled.ro OCTET STRING .1.3.6.1.4.1.173.7.3.8.2.1.22 |
portVoiceOperAutoPollThe flag to enable or disable auto polling. This is
applicable only when the Auto Dial feature is enabled.
When enabled, the node periodically polls the destination.
If the poll is not acknowledged, the node will busy-out
the channel. This can be useful in situations where the
destination is an emergency number that must always be
available. If the destination does not answer the automatic
poll, the busy-out condition will notify an attached PBX
that the emergency call should be routed to another call
routing device.ro Enumeration .1.3.6.1.4.1.173.7.3.8.2.1.23 |
portVoiceOperAutoPollTimerThe frequency with which an Auto Poll will be sent. This
is applicable only when auto poll is enabled.ro INTEGER .1.3.6.1.4.1.173.7.3.8.2.1.24 |
portVoiceOperExtDigitsSourceThe source of the extended digits when the user of
attached equipment dials a speed dial number. This is
applicable only when the number of extended dial digits
is greater than zero. When map is specified, extended
digits are taken from the extended digits field in the
map table. When user is specified, extended digits are
taken from the user of attached equipment.ro Enumeration .1.3.6.1.4.1.173.7.3.8.2.1.25 |
portVoiceOperNumDigitsDeleteThe number of leading dial digits that will be deleted
before a dial string is forwarded. This is primarily used
to delete leading dial digits that may be inserted by an
attached PBX.ro INTEGER .1.3.6.1.4.1.173.7.3.8.2.1.26 |
portVoiceOperForwardDelayThe length of a pause that can be inserted in an extended
dial string that is being forwarded. This is applicable only
when forwarded output digits is all or extended. When a comma
is encountered in an extended digits string, the node will
pause for the length of time specified here before additional
extended digits are forwarded.ro INTEGER .1.3.6.1.4.1.173.7.3.8.2.1.27 |
portVoiceOperForwardedTypeThe method how the dial digits will be forwarded. This
is applicable only when forwarded output digits is all
or extended.ro Enumeration .1.3.6.1.4.1.173.7.3.8.2.1.28 |
portVoiceOperForwardedDigitsThe flag indicating which dial digits, if any, to forward.
If none, dial digits are not forwarded to the destination
device when a call is initiated on this channel. If all,
the dialed speed dial number and associated extended digits
are forwarded to the destination device. If extended, only
the extended digit string is forwarded.ro Enumeration .1.3.6.1.4.1.173.7.3.8.2.1.29 |
portVoiceOperMakeRatioThe make ratio of each digit pulse that is forwarded.
This is applicable only when forwarded output digits
is all or extended and forwarded digit type is pulse.ro INTEGER .1.3.6.1.4.1.173.7.3.8.2.1.30 |
portVoiceOperBreakRatioThe break ratio of each digit pulse that is forwarded.
This is applicable only when forwarded output digits
is all or extended and forwarded digit type is pulse.ro INTEGER .1.3.6.1.4.1.173.7.3.8.2.1.31 |
portVoiceOperDTMFOnDurationThe length of a tone that will be used to produce a
single DTMF digit. This is applicable only when forwarded
output digits is all or extended and forwarded digit type
is DTMF.ro INTEGER .1.3.6.1.4.1.173.7.3.8.2.1.32 |
portVoiceOperDTMFOffDurationThe length of silence between DTMF tones in a dial digit
string. This is applicable only when forwarded output digits
is all or extended and forwarded digit type is DTMF.ro INTEGER .1.3.6.1.4.1.173.7.3.8.2.1.33 |
portVoiceOperToneTypeThe tone type to detect/regenerate for forwarding DTMF/MF.ro Enumeration .1.3.6.1.4.1.173.7.3.8.2.1.34 |
nlInterfaces OBJECT IDENTIFIER .1.3.6.1.4.1.173.7.4 |
nlIfTableA Table to describe each interface on a node.
This table is indexed by RLP and Port number and can be used to
identify the corresponding MIB-II ifIndex of a Port as well as
additional port information maintained by Netlink. SEQUENCE OF NlIfEntry .1.3.6.1.4.1.173.7.4.1 |
nlIfEntryAn Interface entry containing objects relating to interfaces. NlIfEntry .1.3.6.1.4.1.173.7.4.1.1 |
nlIfRlpThe RLP number on the node. RLP numbers 1-8 are Physical
RLP cards, and RLP number 250, 251 and 252 define IP, IPX and LLC2
interfaces respectively.ro INTEGER .1.3.6.1.4.1.173.7.4.1.1.1 |
nlIfPortThe Port number on the RLP. Port numbers 1-8 are
known to be physical ports, and 9-64 are logical ports. If the
RLP number identifies an IP, IPX or LLC2 interface, then the port
number can be 1-257 (IP), 1-64 (IPX), or 1-96 (LLC2).ro INTEGER .1.3.6.1.4.1.173.7.4.1.1.2 |
nlIfTypeThe type of interfacero Enumeration .1.3.6.1.4.1.173.7.4.1.1.3 |
nlIfIndexThe associated index into the MIB-II ifTable for this
portro INTEGER .1.3.6.1.4.1.173.7.4.1.1.4 |
nlIfTableIndexThe associated index into an enterprise table used to
describe additional information for this port. See nlIfTableOid as the
pointer to the actual table.ro INTEGER .1.3.6.1.4.1.173.7.4.1.1.5 |
nlIfTableOidThe OID of the table Entry that contains additional
information about this port. The OID will point to a specific table
depending on the type of port.ro OBJECT IDENTIFIER .1.3.6.1.4.1.173.7.4.1.1.6 |
nlIfConnectorTypeThe physical connector type used for this port. Valid
for ports 1-8 only.ro Enumeration .1.3.6.1.4.1.173.7.4.1.1.7 |
nlIfPortStatusThe status of this port state. Valid for ports 1-64 only.ro Enumeration .1.3.6.1.4.1.173.7.4.1.1.8 |
nlIfPhyPortThe Underlying Physical Port number on the RLP of this
logical port. Port numbers 1-8 are valid, but this field is only
applicable if the nlIfPort field is 9-64.ro INTEGER .1.3.6.1.4.1.173.7.4.1.1.9 |
nlIfLlc2Interfaces OBJECT IDENTIFIER .1.3.6.1.4.1.173.7.4.2 |
nlIfLlc2LANTableA Table to define LLC2 interfaces over LAN. SEQUENCE OF NlIfLlc2LANEntry .1.3.6.1.4.1.173.7.4.2.1 |
nlIfLlc2LANEntryAn LLC2 LAN Interface entry containing objects relating
to LLC2 LAN interfaces. NlIfLlc2LANEntry .1.3.6.1.4.1.173.7.4.2.1.1 |
nlIfLlc2LANRlpThe RLP number on the node. For LLC2 LAN interfaces,
this must be 252.ro INTEGER .1.3.6.1.4.1.173.7.4.2.1.1.1 |
nlIfLlc2LANPortThe Port number on the RLP. For LLC2 LAN interfaces,
this corresponds to the LAN card number.ro INTEGER .1.3.6.1.4.1.173.7.4.2.1.1.2 |
nlIfLlc2LANTypeThe type of the LLC2 interface- either ethernet or
token ring.rw Enumeration .1.3.6.1.4.1.173.7.4.2.1.1.3 |
nlIfLlc2LANCardThe LAN card that the LLC2 interface is running on.ro INTEGER .1.3.6.1.4.1.173.7.4.2.1.1.4 |
nlIfLlc2LANIDValid only if the type of the LLC2 LAN interface is
token ring. Identifies the token ring adapter to the network.rw INTEGER .1.3.6.1.4.1.173.7.4.2.1.1.5 |
nlIfLlc2LANInterfaceThe LLC2 interface number.ro INTEGER .1.3.6.1.4.1.173.7.4.2.1.1.6 |
nlIfLlc2LANRowStatusThis variable is used to manage the creation and deletion
of conceptual rows in the nlIfLlc2LANTable and follows the
SNMPv2 RowStatus conventions by supporting the following values:
- `active', which indicates that the conceptual row is
available for use by the managed device. For a management
protocol set operation, a genErr response is returned when
the row does not exist.
- `createAndGo', which is supplied by a management
station wishing to create a new instance of a
conceptual row and to have its status automatically set
to active, making it available for use by the managed
device. For a management protocol set operation, a
genErr response is returned when the row already exists.
- `destroy', which is supplied by a management station
wishing to delete all of the instances associated with
an existing conceptual row.
Note that all of the above values may be specified in a
management protocol set operation, and only the 'active'
value will be returned in response to a management protocol
retrieval operation. For a management protocol set operation,
if other variable bindings are included in the same PDU, then
a genErr response is returned.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.173.7.4.2.1.1.7 |
nlIfLlc2LANPriorityInterface priority- allows setting a priority for traffic
within the node. The higher the number, the higher the priority relative
to other intra-nodal traffic.rw INTEGER .1.3.6.1.4.1.173.7.4.2.1.1.8 |
nlIfLlc2LANBlockedPortFlagThe blocked port flag.rw Enumeration .1.3.6.1.4.1.173.7.4.2.1.1.9 |
nlIfLlc2FrTableA Table to define LLC2 interfaces over Frame Relay. SEQUENCE OF NlIfLlc2FrEntry .1.3.6.1.4.1.173.7.4.2.2 |
nlIfLlc2FrEntryAn LLC2 FR Interface entry containing objects relating
to LLC2 FR interfaces. NlIfLlc2FrEntry .1.3.6.1.4.1.173.7.4.2.2.1 |
nlIfLlc2FrRlpThe RLP number on the node.ro INTEGER .1.3.6.1.4.1.173.7.4.2.2.1.1 |
nlIfLlc2FrPortThe Port number on the RLP. Port numbers 1-8 are
known to be physical ports, and channels are 193-241.ro INTEGER .1.3.6.1.4.1.173.7.4.2.2.1.2 |
nlIfLlc2FrDLCIThe DLCI number used to identify the entry in the table.
The range is 16-991.ro INTEGER .1.3.6.1.4.1.173.7.4.2.2.1.3 |
nlIfLlc2FrFormatThe RFC1490 encapsulation method used for LLC2 traffic.ro Enumeration .1.3.6.1.4.1.173.7.4.2.2.1.4 |
nlIfLlc2FrPriorityInterface priority- allows setting a priority for traffic
within the node. The higher the number, the higher the priority relative
to other intra-nodal traffic.rw INTEGER .1.3.6.1.4.1.173.7.4.2.2.1.5 |
nlIfLlc2FrBAGAssigns the interface to one of sixteen groups whose parameters
regulate bandwidth usage.rw INTEGER .1.3.6.1.4.1.173.7.4.2.2.1.6 |
nlIfLlc2FrHostMACAddressThe MAC address of the host or workstation to which
the remote device needs to connect. Valid only if the format is
native-llc2.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.173.7.4.2.2.1.7 |
nlIfLlc2FrSessionTypeIf originated, means that LLC2 connects from the configured
Host MAC address can use this interface. If terminated, connections to
the configured address can use this interface. Valid only if the
format is native-llc2.rw Enumeration .1.3.6.1.4.1.173.7.4.2.2.1.8 |
nlIfLlc2FrLANIDIdentifies the ring number used by a frame relay-compliant
source-route bridge at the other end of this PVC. Valid only if the
format is srb-8025.rw INTEGER .1.3.6.1.4.1.173.7.4.2.2.1.9 |
nlIfLlc2FrInterfaceLLC2 interface number.ro INTEGER .1.3.6.1.4.1.173.7.4.2.2.1.10 |
nlIfLlc2FrRowStatusThis variable is used to manage the creation and deletion
of conceptual rows in the nlIfLlc2FrTable and follows the
SNMPv2 RowStatus conventions by supporting the following values:
- `active', which indicates that the conceptual row is
available for use by the managed device. For a management
protocol set operation, a genErr response is returned when
the row does not exist.
- `createAndGo', which is supplied by a management
station wishing to create a new instance of a
conceptual row and to have its status automatically set
to active, making it available for use by the managed
device. For a management protocol set operation, a
genErr response is returned when the row already exists.
- `destroy', which is supplied by a management station
wishing to delete all of the instances associated with
an existing conceptual row.
Note that all of the above values may be specified in a
management protocol set operation, and only the 'active'
value will be returned in response to a management protocol
retrieval operation. For a management protocol set operation,
if other variable bindings are included in the same PDU, then
a genErr response is returned.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.173.7.4.2.2.1.11 |
nlIfLlc2FrBlockedPortFlagThe blocked port flag.rw Enumeration .1.3.6.1.4.1.173.7.4.2.2.1.12 |
ipxConfig OBJECT IDENTIFIER .1.3.6.1.4.1.173.7.4.3 |
ipxConfigRouting OBJECT IDENTIFIER .1.3.6.1.4.1.173.7.4.3.1 |
ipxStaticRouteConfigTableThe IPX Static Route Configuration Table SEQUENCE OF IPXStaticRouteConfigEntry .1.3.6.1.4.1.173.7.4.3.1.1 |
ipxStaticRouteConfigEntryEach entry corresponds to one instance of IPX Static Routing on the system IPXStaticRouteConfigEntry .1.3.6.1.4.1.173.7.4.3.1.1.1 |
ipxStaticRouteConfigCircIndexThe unique identifier of the circuit used to reach the
first hop in the static routero INTEGER .1.3.6.1.4.1.173.7.4.3.1.1.1.1 |
ipxStaticRouteConfigNetNumThe IPX network number of the route's destinationro OCTET STRING .1.3.6.1.4.1.173.7.4.3.1.1.1.2 |
ipxStaticRouteConfigRouterThe hex value of the node address of the router that will forward a packet when this route is used.
If Novell's IPXWAN is used on the interface, this field will be ignoredrw OCTET STRING .1.3.6.1.4.1.173.7.4.3.1.1.1.3 |
ipxStaticRouteConfigRowStatusThis variable is used to manage the creation and deletion
of conceptual rows in the ipxStaticRouteTable and follows the
SNMPv2 RowStatus conventions by supporting the following values:
- `active', which indicates that the conceptual row is
available for use by the managed device. For a management
protocol set operation, a genErr response is returned when
the row does not exist.
- `createAndGo', which is supplied by a management
station wishing to create a new instance of a
conceptual row and to have its status automatically set
to active, making it available for use by the managed
device. For a management protocol set operation, a
genErr response is returned when the row already exists.
- `destroy', which is supplied by a management station
wishing to delete all of the instances associated with
an existing conceptual row.
Note that all of the above values may be specified in a
management protocol set operation, and only the 'active'
value will be returned in response to a management protocol
retrieval operation. For a management protocol set operation,
if other variable bindings are included in the same PDU, then
a genErr response is returned.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.173.7.4.3.1.1.1.4 |
ipxServConfigTableThe IPX Static Route Configuration Table SEQUENCE OF IPXServConfigEntry .1.3.6.1.4.1.173.7.4.3.1.2 |
ipxServConfigEntryEach entry corresponds to one instance of IPX Static Routing on the system IPXServConfigEntry .1.3.6.1.4.1.173.7.4.3.1.2.1 |
ipxServConfigServiceTypeThe Service Type, a SAP service codero INTEGER .1.3.6.1.4.1.173.7.4.3.1.2.1.1 |
ipxServConfigServNameThe Sercice Name, identifies a specific server in the IPX network.ro OCTET STRING .1.3.6.1.4.1.173.7.4.3.1.2.1.2 |
ipxServConfigServNetworkAddressThe IPX network number portion of the IPX address of the server identified by ServNamerw INTEGER .1.3.6.1.4.1.173.7.4.3.1.2.1.3 |
ipxServConfigServNodeAddressThe node portion of the IPX address of the servicerw OCTET STRING .1.3.6.1.4.1.173.7.4.3.1.2.1.4 |
ipxServConfigServSocketNumberThe socket portion of the IPX address of the servicerw INTEGER .1.3.6.1.4.1.173.7.4.3.1.2.1.5 |
ipxServConfigInterveningNetworksThe number of routers that a packet must pass through t reach the serverrw INTEGER .1.3.6.1.4.1.173.7.4.3.1.2.1.6 |
ipxServConfigGatewayAddressThe node address of the router thar will forward a packetrw OCTET STRING .1.3.6.1.4.1.173.7.4.3.1.2.1.7 |
ipxServConfigInterfaceThe IPX network number assigned to the interface used to send packets that are destined for this serverrw INTEGER .1.3.6.1.4.1.173.7.4.3.1.2.1.8 |
ipxServConfigRowStatusThis variable is used to manage the creation and deletion
of conceptual rows in the ipxServTable and follows the
SNMPv2 RowStatus conventions by supporting the following values:
- `active', which indicates that the conceptual row is
available for use by the managed device. For a management
protocol set operation, a genErr response is returned when
the row does not exist.
- `createAndGo', which is supplied by a management
station wishing to create a new instance of a
conceptual row and to have its status automatically set
to active, making it available for use by the managed
device. For a management protocol set operation, a
genErr response is returned when the row already exists.
- `destroy', which is supplied by a management station
wishing to delete all of the instances associated with
an existing conceptual row.
Note that all of the above values may be specified in a
management protocol set operation, and only the 'active'
value will be returned in response to a management protocol
retrieval operation. For a management protocol set operation,
if other variable bindings are included in the same PDU, then
a genErr response is returned.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.173.7.4.3.1.2.1.9 |
ipxConfigInterface OBJECT IDENTIFIER .1.3.6.1.4.1.173.7.4.3.2 |
ipxInterfaceTableThe IPX Interface Table SEQUENCE OF IPXInterfaceEntry .1.3.6.1.4.1.173.7.4.3.2.6 |
ipxInterfaceEntry IPXInterfaceEntry .1.3.6.1.4.1.173.7.4.3.2.6.1 |
ipxInterfaceNumberThe Interface Number, a sequential number to identify the interfacero INTEGER .1.3.6.1.4.1.173.7.4.3.2.6.1.1 |
ipxInterfaceBlockedPortFlagThis flag causes the IPX interface to be enabled (N) or disabled (Y) at node IPL. The port
will remain in that state until this parameter is changedrw Enumeration .1.3.6.1.4.1.173.7.4.3.2.6.1.2 |
ipxInterfaceTypeThe interface type. 802.5 is not valid on FRX4000rw Enumeration .1.3.6.1.4.1.173.7.4.3.2.6.1.3 |
ipxInterfaceFrameTypeThe frame type - depends on the interfece type. Valid combinations are:
Ethernet, 802.5 - typeII, raw, llc, snap
Frame relay, X25 - typeIIrw Enumeration .1.3.6.1.4.1.173.7.4.3.2.6.1.4 |
ipxInterfaceMaxTransUnitMaximum frame size that can be transmitted or received over the IPX interface.: Valid ranges are:
Ethernet - (45-1518)
802.5 - (48-4096)
Frame relay, X25 - (31-4096)rw INTEGER .1.3.6.1.4.1.173.7.4.3.2.6.1.5 |
ipxInterfaceNetworkAddressIdentifies the local interface to the Novell Networkrw INTEGER .1.3.6.1.4.1.173.7.4.3.2.6.1.6 |
ipxInterfaceBandwidthAllocGroupAssigns the IPX interface to one of sixteen groups whose parameters regulate bandwidth usagerw INTEGER .1.3.6.1.4.1.173.7.4.3.2.6.1.7 |
ipxInterfacePortDiagEnabledEnables/Disables the IPX interface's ability to handle Novell diagonistics packetsrw Enumeration .1.3.6.1.4.1.173.7.4.3.2.6.1.8 |
ipxInterfaceNetBIOSEnabledDetermines whether Novell-encapsulated NetBIOS
frames received on the interface will be processedrw Enumeration .1.3.6.1.4.1.173.7.4.3.2.6.1.9 |
ipxInterfaceNetBIOSHopsMaximum number of hops allowed for routing a Novell-encapsulated NetBIOS framerw INTEGER .1.3.6.1.4.1.173.7.4.3.2.6.1.10 |
ipxInterfacePeriodicRIPEnabledDetermines whether the node will originate periodic IPX Routing Information Protocol messages
from this interface to inform the network that the route through this interface is viablerw Enumeration .1.3.6.1.4.1.173.7.4.3.2.6.1.11 |
ipxInterfacePeriodicRIPTimerThis is the interval between the periodic IPX RIP broadcasts from this interfacerw INTEGER .1.3.6.1.4.1.173.7.4.3.2.6.1.12 |
ipxInterfacePeriodicSAPEnabledDetermines whether the node will originate periodic IPX SAP messages
from this interface to inform the network which SAP entries in the routing table are viablerw Enumeration .1.3.6.1.4.1.173.7.4.3.2.6.1.13 |
ipxInterfacePeriodicSAPTimerThe interval between the periodic SAP broadcasts from this interfacerw INTEGER .1.3.6.1.4.1.173.7.4.3.2.6.1.14 |
ipxInterfaceRIPEnabledDatermines whether this interface will support RIP proceswsingrw Enumeration .1.3.6.1.4.1.173.7.4.3.2.6.1.15 |
ipxInterfaceRIPAgeTimerThis is used to delete route entries in the routing information table. The timer starts/restarts
each time an entry is created/updated. If the timer expires, the router will assume that the entry is no
longer valid and the entry will be deleteda from the tablerw INTEGER .1.3.6.1.4.1.173.7.4.3.2.6.1.16 |
ipxInterfaceRIPMaxSizeMaximum possible RIP packet sizerw INTEGER .1.3.6.1.4.1.173.7.4.3.2.6.1.17 |
ipxInterfaceSAPEnabledDetermines whether the interface will support SAP or notrw Enumeration .1.3.6.1.4.1.173.7.4.3.2.6.1.18 |
ipxInterfaceSAPAgeTimerThis is used to delete route entries from the router information table. The timer starts/restars
each time an entry is created/updated. If the timer expires, the router will assume that the entry is no
longer valid and the entry will be deleted from the tablerw INTEGER .1.3.6.1.4.1.173.7.4.3.2.6.1.19 |
ipxInterfaceTransportTimeis the time (in 55 milliseconds unit) that will normally take to forward frames out of interface.
Recommmended values are 1 for LAN interfaces and 30 for WAN interfaces. A value of 0 indicates that the
back to back frame forwarding is acceptable. This time is used to calculate the least cost path during
routing. If IPXWAMN is (Y), Transport time will be overridden by the value calculated by IPXWANrw INTEGER .1.3.6.1.4.1.173.7.4.3.2.6.1.20 |
ipxInterfaceSerializationEnabledDetermines whether NetWare file server serialization security frames will be
forwarded on the interface. These broadcasts frames are used by Novell to hold informations regarding the
licensing of the file server executablesrw Enumeration .1.3.6.1.4.1.173.7.4.3.2.6.1.21 |
ipxInterfaceWatchdogSpoofingEnabledDetermines whether this interface will be used by the local node to respond to (keep alive) messages on
behalf of the client workstations. Novell servers periodically issue these messages to all clients
to determine whether each client is still aliverw Enumeration .1.3.6.1.4.1.173.7.4.3.2.6.1.22 |
ipxInterfaceLanCardNumberThe card number installed in an FRX6000. The first or only LAN card installed is always 0,
and the second is card 1rw INTEGER .1.3.6.1.4.1.173.7.4.3.2.6.1.23 |
ipxInterfaceWanEnabledDetermines whether Novell's IPXWAN protocol will be used on the interface. IPXWAN specifies a method
for IPX routers to communicate across WAN links. FRX6000 and FRX4000 implement IPXWAN running over RFC
1490-complaint frame relay and RFC1356-complaint X.25rw Enumeration .1.3.6.1.4.1.173.7.4.3.2.6.1.24 |
ipxInterfaceSourceSubscriberSubscruber id that defines an IPX interface in the node, by associating itself with port 66 (a
number reserved for the IPXinterface) on the RLP that has an IPX installed on it.
.. Valid only for type X.25rw OCTET STRING .1.3.6.1.4.1.173.7.4.3.2.6.1.25 |
ipxInterfaceDestinationSubscriberSubscriber ID associated with the physical X.25 port that will be used for the IPX interface .
.. Valid only for type X.25rw OCTET STRING .1.3.6.1.4.1.173.7.4.3.2.6.1.26 |
ipxInterfaceSVCRetryTimerThe frequency with which calls will be placed to try to establish a connection
.. Valid only for type X.25rw INTEGER .1.3.6.1.4.1.173.7.4.3.2.6.1.27 |
ipxInterfaceSVCIdleTimeris a period that an IPX connection can remain active with no traffic before the connection is cleared.
.. Valid only for type X.25rw INTEGER .1.3.6.1.4.1.173.7.4.3.2.6.1.28 |
ipxInterfaceMaxVCThis specifies a number of virtual circuits over which IPX traffic will be transmitted in parallel.
.. Valid only for type X.25rw INTEGER .1.3.6.1.4.1.173.7.4.3.2.6.1.29 |
ipxInterfacePVCConnectionIdentifies this interface as one of a PVC.
.. Valid only for type X.25rw Enumeration .1.3.6.1.4.1.173.7.4.3.2.6.1.30 |
ipxInterfaceSourceCardIdentifies the location of this end of the frame relay IPX interface.
.. Valid only for frame relayrw INTEGER .1.3.6.1.4.1.173.7.4.3.2.6.1.31 |
ipxInterfaceSourcePortIdentifies the location of this end of the frame relay IPX interface.
.. Valid only for frame relayrw INTEGER .1.3.6.1.4.1.173.7.4.3.2.6.1.32 |
ipxInterfaceSourceDLCIIdentifies the location of this end of the frame relay IPX interface.
.. Valid only for frame relayrw INTEGER .1.3.6.1.4.1.173.7.4.3.2.6.1.33 |
ipxInterfaceRowStatusThis variable is used to manage the creation and deletion
of conceptual rows in the ipxInterfaceTable and follows the
SNMPv2 RowStatus conventions by supporting the following values:
- `active', which indicates that the conceptual row is
available for use by the managed device. For a management
protocol set operation, a genErr response is returned when
the row does not exist.
- `createAndGo', which is supplied by a management
station wishing to create a new instance of a
conceptual row and to have its status automatically set
to active, making it available for use by the managed
device. For a management protocol set operation, a
genErr response is returned when the row already exists.
- `destroy', which is supplied by a management station
wishing to delete all of the instances associated with
an existing conceptual row.
Note that all of the above values may be specified in a
management protocol set operation, and only the 'active'
value will be returned in response to a management protocol
retrieval operation. For a management protocol set operation,
if other variable bindings are included in the same PDU, then
a genErr response is returned.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.173.7.4.3.2.6.1.34 |
ipxConfigNodeDefault OBJECT IDENTIFIER .1.3.6.1.4.1.173.7.4.3.3 |
ipxNodeDefaultConfigNetworkAddressIdentifies the node to the IPX networkrw INTEGER .1.3.6.1.4.1.173.7.4.3.3.1 |
ipxNodeDefaultConfigRIPSAPGapThe minimum delay between consecutive RIP and SAP transmissionsrw INTEGER .1.3.6.1.4.1.173.7.4.3.3.2 |
ipxNodeDefaultConfigRouterNameAn unique identifier within the IPX networkrw OCTET STRING .1.3.6.1.4.1.173.7.4.3.3.3 |
nlIfIpInterfaces OBJECT IDENTIFIER .1.3.6.1.4.1.173.7.4.4 |
nlIfIpTableA Table to define IP interfaces over frame relay,
X.25, or LAN (ethernet, 802.3, 802.5). SEQUENCE OF NlIfIpEntry .1.3.6.1.4.1.173.7.4.4.1 |
nlIfIpEntryAn IP Interface entry containing objects relating
to IP interfaces. NlIfIpEntry .1.3.6.1.4.1.173.7.4.4.1.1 |
nlIfIpInterfaceThe interface number which uniquely identifies the
interface to which this entry is applicable. The
interface identified by a particular value of this
number is NOT the same interface as defined by the
same value of ifIndex.ro INTEGER .1.3.6.1.4.1.173.7.4.4.1.1.1 |
nlIfIpMtuThe maximum size (in bytes) of the data field that can
be used to encapsulate an IP datagram for transmission
over the interface. If the interface type is LAN based,
then the maximum size value cannot exceed 1500.rw INTEGER .1.3.6.1.4.1.173.7.4.4.1.1.2 |
nlIfIpNetworkMaskThe mask used during routing to determine the portion
of the address associated with the network.rw IpAddress .1.3.6.1.4.1.173.7.4.4.1.1.3 |
nlIfIpRouteMetricThe number of network hops (network gateways in the
overall path over the internet) associated with this
interface.rw INTEGER .1.3.6.1.4.1.173.7.4.4.1.1.4 |
nlIfIpICMPAddRoutesThe flag which indicates whether IP may add routes
obtained by ICMP, whose error and control function
is used to send re-direction options back to the
source if problems are discovered.rw Enumeration .1.3.6.1.4.1.173.7.4.4.1.1.5 |
nlIfIpRIPDeltaUpdatesThe frequency with which RIP messages will be sent to
every neighbor node, containing any changes to the
routing table that occurred since the last full update.rw INTEGER .1.3.6.1.4.1.173.7.4.4.1.1.6 |
nlIfIpRIPFullUpdatesThe frequency with which updates of the entire routing
table will be sent to every neighbor node, via one or
more RIP messages.rw INTEGER .1.3.6.1.4.1.173.7.4.4.1.1.7 |
nlIfIpPriorityThe priority setting for traffic within the node. The
higher the number, the higher the priority relative to
other intra-nodal traffic.rw INTEGER .1.3.6.1.4.1.173.7.4.4.1.1.8 |
nlIfIpBAGThe bandwidth allocation group to which this interface
is assigned to. This object is only valid when the
interface type is frame relay or proprietary virtual.rw INTEGER .1.3.6.1.4.1.173.7.4.4.1.1.9 |
nlIfIpTypeThe type of IP interface.rw Enumeration .1.3.6.1.4.1.173.7.4.4.1.1.10 |
nlIfIpSourceAddressThe IP address of the end-to-end sender.rw IpAddress .1.3.6.1.4.1.173.7.4.4.1.1.11 |
nlIfIpDestAddressThe IP address of the end-to-end receiver. This object
is only valid when the interface type is X.25 or proprietary
virtual, or when the interface type is frame relay and the
inverse ARP flag indicates disabled.rw IpAddress .1.3.6.1.4.1.173.7.4.4.1.1.12 |
nlIfIpBroadcastAddressThe IP address that is used to send to all LAN hosts
on the network. This object is only valid when the
interface type is LAN based.rw IpAddress .1.3.6.1.4.1.173.7.4.4.1.1.13 |
nlIfIpLANCardThe LAN card that contains the interface. This object
is only valid when the interface type is LAN based.rw INTEGER .1.3.6.1.4.1.173.7.4.4.1.1.14 |
nlIfIpSourceSubThe subscriber ID associated with the source IP
interface port. This object is only valid when the
interface type is X.25.rw NlSubscriberAddress .1.3.6.1.4.1.173.7.4.4.1.1.15 |
nlIfIpDestSubThe subscriber ID associated with the destination IP
interface port. This object is only valid when the
interface type is X.25.rw NlSubscriberAddress .1.3.6.1.4.1.173.7.4.4.1.1.16 |
nlIfIpSVCRetryTimerThe frequency with which calls will be placed to try
to establish a connection. This object is only valid
when the interface type is X.25.rw INTEGER .1.3.6.1.4.1.173.7.4.4.1.1.17 |
nlIfIpSVCIdleTimerThe period that an IP connection remains active with
no traffic before the connection is cleared. This object
is only valid when the interface type is X.25.rw INTEGER .1.3.6.1.4.1.173.7.4.4.1.1.18 |
nlIfIpMaxSVCThe number of virtual circuits over which IP traffic
will be transmitted in parallel. This object is only
valid when the interface type is X.25.rw INTEGER .1.3.6.1.4.1.173.7.4.4.1.1.19 |
nlIfIpPVCConnectionThe flag which indicates whether this interface is a
PVC. This object is only valid when the interface type
is X.25.rw Enumeration .1.3.6.1.4.1.173.7.4.4.1.1.20 |
nlIfIpSourceRlpThe RLP of the logical interface of this end of the frame
relay link. This object is only valid when the interface
type is frame relay.rw INTEGER .1.3.6.1.4.1.173.7.4.4.1.1.21 |
nlIfIpSourcePortThe port of the logical interface of this end of the frame
relay link. This object is only valid when the interface
type is frame relay.rw INTEGER .1.3.6.1.4.1.173.7.4.4.1.1.22 |
nlIfIpSourceDLCIThe DLCI of the logical interface of this end of the frame
relay link. This object is only valid when the interface
type is frame relay.rw INTEGER .1.3.6.1.4.1.173.7.4.4.1.1.23 |
nlIfIpRIPSupportThe RIP support that is being run on the interface.rw Enumeration .1.3.6.1.4.1.173.7.4.4.1.1.24 |
nlIfIpInverseARPThe flag which indicates whether inverse ARP is enabled
or disabled. This object is only valid when the interface
type is frame relay.rw Enumeration .1.3.6.1.4.1.173.7.4.4.1.1.25 |
nlIfIpProxyARPThe flag which indicates whether proxy ARP is enabled
or disabled. This object is only valid when the interface
type is LAN based.rw Enumeration .1.3.6.1.4.1.173.7.4.4.1.1.26 |
nlIfIpUnnumberedIfThe flag which indicates whether this interface is an
unnumbered interface (i.e., does not require a specific
source IP address). This object is only valid when the
interface type is frame relay or X.25.rw Enumeration .1.3.6.1.4.1.173.7.4.4.1.1.27 |
nlIfIpRowStatusThis variable is used to manage the creation and deletion
of conceptual rows in the nlIfIpTable and follows the SNMPv2
RowStatus conventions by supporting the following values:
- `active', which indicates that the conceptual row is
available for use by the managed device. For a management
protocol set operation, a genErr response is returned when
the row does not exist.
- `createAndGo', which is supplied by a management
station wishing to create a new instance of a
conceptual row and to have its status automatically set
to active, making it available for use by the managed
device. For a management protocol set operation, a
genErr response is returned when the row already exists.
- `destroy', which is supplied by a management station
wishing to delete all of the instances associated with
an existing conceptual row.
Note that all of the above values may be specified in a
management protocol set operation, and only the 'active'
value will be returned in response to a management protocol
retrieval operation. For a management protocol set operation,
if other variable bindings are included in the same PDU, then
a genErr response is returned.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.173.7.4.4.1.1.28 |
nlIfIpSecondaryAddrTableA Table to define secondary IP interfaces on a
LAN (ethernet, 802.3, 802.5) interface. SEQUENCE OF NlIfIpSecondaryAddrEntry .1.3.6.1.4.1.173.7.4.4.2 |
nlIfIpSecondaryAddrEntryAn IP Secondary Address entry containing objects relating
to IP secondary addresses. NlIfIpSecondaryAddrEntry .1.3.6.1.4.1.173.7.4.4.2.1 |
nlIfIpSecondaryAddrSequenceThe maximum number of secondary IP addresses that may
be configured on an interface.rw INTEGER .1.3.6.1.4.1.173.7.4.4.2.1.1 |
nlIfIpSecondaryAddrNetworkMaskThe mask used during routing to determine the portion
of the address associated with the network.rw IpAddress .1.3.6.1.4.1.173.7.4.4.2.1.2 |
nlIfIpSecondaryAddrRouteMetricThe number of network hops (network gateways in the
overall path over the internet) associated with this
interface.rw INTEGER .1.3.6.1.4.1.173.7.4.4.2.1.3 |
nlIfIpSecondaryAddrSourceAddressThe IP address of the end-to-end sender.rw IpAddress .1.3.6.1.4.1.173.7.4.4.2.1.4 |
nlIfIpSecondaryAddrBroadcastAddressThe IP address that is used to send to all LAN hosts
on the network.rw IpAddress .1.3.6.1.4.1.173.7.4.4.2.1.5 |
nlIfIpSecondaryAddrRIPSupportThe RIP support that is being run on the interface.rw Enumeration .1.3.6.1.4.1.173.7.4.4.2.1.6 |
nlIfIpSecondaryAddrRowStatusThis variable is used to manage the creation and deletion of
conceptual rows in the nlIfIpSecondaryAddrTable and follows the
SNMPv2 RowStatus conventions by supporting the following values:
- `active', which indicates that the conceptual row is
available for use by the managed device. For a management
protocol set operation, a genErr response is returned when
the row does not exist.
- `createAndGo', which is supplied by a management
station wishing to create a new instance of a
conceptual row and to have its status automatically set
to active, making it available for use by the managed
device. For a management protocol set operation, a
genErr response is returned when the row already exists.
- `destroy', which is supplied by a management station
wishing to delete all of the instances associated with
an existing conceptual row.
Note that all of the above values may be specified in a
management protocol set operation, and only the 'active'
value will be returned in response to a management protocol
retrieval operation. For a management protocol set operation,
if other variable bindings are included in the same PDU, then
a genErr response is returned.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.173.7.4.4.2.1.7 |
nlIfVoiceInterfaces OBJECT IDENTIFIER .1.3.6.1.4.1.173.7.4.5 |
nlIfVoiceTableA Table to define Voice interfaces over frame relay. SEQUENCE OF NlIfVoiceEntry .1.3.6.1.4.1.173.7.4.5.1 |
nlIfVoiceEntryA Voice Interface entry containing objects relating
to the interface that are configurable by the user. NlIfVoiceEntry .1.3.6.1.4.1.173.7.4.5.1.1 |
nlIfVoiceInterfaceThe interface number which uniquely identifies the
interface to which this entry is applicable. The
interface identified by a particular value of this
number is NOT the same interface as defined by the
same value of ifIndex.ro INTEGER .1.3.6.1.4.1.173.7.4.5.1.1.1 |
nlIfVoicePeerNodeTypeThe node type for the node at the remote end of the
frame relay connection.rw Enumeration .1.3.6.1.4.1.173.7.4.5.1.1.2 |
nlIfVoicePeerNodeNumberThe node number of the remote device.rw INTEGER .1.3.6.1.4.1.173.7.4.5.1.1.3 |
nlIfVoicePeerNodePortThe voice port on the remote device.rw INTEGER .1.3.6.1.4.1.173.7.4.5.1.1.4 |
nlIfVoiceLocalNodeNumberThe node number of the local device.rw INTEGER .1.3.6.1.4.1.173.7.4.5.1.1.5 |
nlIfVoiceLocalNodePortThe voice port on the local device.rw INTEGER .1.3.6.1.4.1.173.7.4.5.1.1.6 |
nlIfVoiceFrameRelayRlpThe RLP of the logical interface of this end of the frame
relay link.rw INTEGER .1.3.6.1.4.1.173.7.4.5.1.1.7 |
nlIfVoiceFrameRelayPortThe port of the logical interface of this end of the frame
relay link.rw INTEGER .1.3.6.1.4.1.173.7.4.5.1.1.8 |
nlIfVoiceFrameRelayDLCIThe DLCI of the logical interface of this end of the frame
relay link.rw INTEGER .1.3.6.1.4.1.173.7.4.5.1.1.9 |
nlIfVoiceEnableFragmentrw Enumeration .1.3.6.1.4.1.173.7.4.5.1.1.10 |
nlIfVoiceRowStatusThis variable is used to manage the creation and deletion
of conceptual rows in the noIfVoiceTable and follows the
SNMPv2 RowStatus conventions by supporting the following values:
- `active', which indicates that the conceptual row is
available for use by the managed device. For a management
protocol set operation, a genErr response is returned when
the row does not exist.
- `createAndGo', which is supplied by a management
station wishing to create a new instance of a
conceptual row and to have its status automatically set
to active, making it available for use by the managed
device. For a management protocol set operation, a
genErr response is returned when the row already exists.
- `destroy', which is supplied by a management station
wishing to delete all of the instances associated with
an existing conceptual row.
Note that all of the above values may be specified in a
management protocol set operation, and only the 'active'
value will be returned in response to a management protocol
retrieval operation. For a management protocol set operation,
if other variable bindings are included in the same PDU, then
a genErr response is returned.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.173.7.4.5.1.1.11 |
subscriber OBJECT IDENTIFIER .1.3.6.1.4.1.173.7.5 |
nlLocalSubscriberTableA Table to define each local subscriber. SEQUENCE OF NlLocalSubscriberEntry .1.3.6.1.4.1.173.7.5.1 |
nlLocalSubscriberEntryA Local Subscriber entry containing objects relating
to local subscribers. NlLocalSubscriberEntry .1.3.6.1.4.1.173.7.5.1.1 |
nlLocalSubscriberIdThe Subscriber ID. A valid subscriber ID is a string of
numeric digits represented by their ASCII equivalents. The
ASCII equivalents of the wildcard characters '*' and '?' are
also allowed. A '*' is a wildcard that matches any number of
digits, including zero. A '?' is a wildcard that matches any single digit.ro NlSubscriberAddress .1.3.6.1.4.1.173.7.5.1.1.1 |
nlLocalSubscriberNameThe Subscriber name. The subscriber name is not accessible from
SNMP, and a blank string is always returned.ro DisplayString .1.3.6.1.4.1.173.7.5.1.1.2 |
nlLocalSubscriberAlgorithmThe Subscriber routing algorithm.
The following 4 types of routing algorithms are supported.
1 - round robin selects ports specified cyclicly in numerical
order according to the list of Redirection addresses. If the port
is unreachable or congested, the call request is sent to the next
port.
2. Alternate Route on Line Failure - selects the first port
not in a failed state. If a connection is not made, the call
will be cleared even if other ports are available.
3. Alternate Route on Line Busy - selects the first port
that has LCN's available (not busy). If a port has failed,
the next available port is selected.
4. Least LCN with throughput selects the line with the minumum
loading, calculated by weight and number of LCN's in use.
If use of a routing algorithm is not desired, accept the default
and specify only one routing path.rw Enumeration .1.3.6.1.4.1.173.7.5.1.1.3 |
nlLocalSubscriberSystematicRedirectSystematic Redirection.rw Enumeration .1.3.6.1.4.1.173.7.5.1.1.4 |
nlLocalSubscriberRedirectBusyRedirect calls according to Redirection Addresses if the
primary subscriber device is busy.rw Enumeration .1.3.6.1.4.1.173.7.5.1.1.5 |
nlLocalSubscriberRedirectOORedirect calls according to Redirection Addresses if the
primary subscriber device is out of order.rw Enumeration .1.3.6.1.4.1.173.7.5.1.1.6 |
nlLocalSubscriberPriorityAllows setting a priority for traffic within the node.rw INTEGER .1.3.6.1.4.1.173.7.5.1.1.7 |
nlLocalSubscriberRowStatusThis variable is used to manage the creation and deletion
of conceptual rows in the nlLocalSubscriberTable and follows the
SNMPv2 RowStatus conventions by supporting the following values:
- `active', which indicates that the conceptual row is
available for use by the managed device. For a management
protocol set operation, a genErr response is returned when
the row does not exist.
- `createAndGo', which is supplied by a management
station wishing to create a new instance of a
conceptual row and to have its status automatically set
to active, making it available for use by the managed
device. For a management protocol set operation, a
genErr response is returned when the row already exists.
- `destroy', which is supplied by a management station
wishing to delete all of the instances associated with
an existing conceptual row.
Note that all of the above values may be specified in a
management protocol set operation, and only the 'active'
value will be returned in response to a management protocol
retrieval operation. For a management protocol set operation,
if other variable bindings are included in the same PDU, then
a genErr response is returned.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.173.7.5.1.1.8 |
nlLocalSubscriberRouteTableA Table to define local subscriber route paths. SEQUENCE OF NlLocalSubscriberRouteEntry .1.3.6.1.4.1.173.7.5.2 |
nlLocalSubscriberRouteEntryA Local Subscriber Route entry containing objects relating
to local subscriber routes. NlLocalSubscriberRouteEntry .1.3.6.1.4.1.173.7.5.2.1 |
nlLocalSubscriberRouteIndexRoute path index for a specific subscriber route path.ro INTEGER .1.3.6.1.4.1.173.7.5.2.1.1 |
nlLocalSubscriberRouteConfFlag to indicate if the LP/port routing path to the
subscriber device is configured or not. This object is read-
only. The route is always configured for an entry in the table.ro Enumeration .1.3.6.1.4.1.173.7.5.2.1.2 |
nlLocalSubscriberRouteLPInstance of the LP that makes up the routing pathrw INTEGER .1.3.6.1.4.1.173.7.5.2.1.3 |
nlLocalSubscriberRoutePortInstance of the port that makes up the routing pathrw INTEGER .1.3.6.1.4.1.173.7.5.2.1.4 |
nlLocalSubscriberRouteRowStatusThis variable is used to manage the creation and deletion
of conceptual rows in the nlLocalSubscriberRouteTable and follows the
SNMPv2 RowStatus conventions by supporting the following values:
- `active', which indicates that the conceptual row is
available for use by the managed device. For a management
protocol set operation, a genErr response is returned when
the row does not exist.
- `createAndGo', which is supplied by a management
station wishing to create a new instance of a
conceptual row and to have its status automatically set
to active, making it available for use by the managed
device. For a management protocol set operation, a
genErr response is returned when the row already exists.
- `destroy', which is supplied by a management station
wishing to delete all of the instances associated with
an existing conceptual row.
Note that all of the above values may be specified in a
management protocol set operation, and only the 'active'
value will be returned in response to a management protocol
retrieval operation. For a management protocol set operation,
if other variable bindings are included in the same PDU, then
a genErr response is returned.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.173.7.5.2.1.5 |
nlLocalSubscriberRedirTableA Table to list local subscriber redirection addresses. SEQUENCE OF NlLocalSubscriberRedirEntry .1.3.6.1.4.1.173.7.5.3 |
nlLocalSubscriberRedirEntryA Local Subscriber Redirection Address entry containing
objects relating to local subscriber redirection addresses. NlLocalSubscriberRedirEntry .1.3.6.1.4.1.173.7.5.3.1 |
nlLocalSubscriberRedirIndexRedirection entry index for a local subscriber.ro INTEGER .1.3.6.1.4.1.173.7.5.3.1.1 |
nlLocalSubscriberRedirAddrSubscriber redirection address.rw NlSubscriberAddress .1.3.6.1.4.1.173.7.5.3.1.2 |
nlLocalSubscriberRedirRowStatusThis variable is used to manage the creation and deletion
of conceptual rows in the nlLocalSubscriberRedirTable and follows the
SNMPv2 RowStatus conventions by supporting the following values:
- `active', which indicates that the conceptual row is
available for use by the managed device. For a management
protocol set operation, a genErr response is returned when
the row does not exist.
- `createAndGo', which is supplied by a management
station wishing to create a new instance of a
conceptual row and to have its status automatically set
to active, making it available for use by the managed
device. For a management protocol set operation, a
genErr response is returned when the row already exists.
- `destroy', which is supplied by a management station
wishing to delete all of the instances associated with
an existing conceptual row.
Note that all of the above values may be specified in a
management protocol set operation, and only the 'active'
value will be returned in response to a management protocol
retrieval operation. For a management protocol set operation,
if other variable bindings are included in the same PDU, then
a genErr response is returned.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.173.7.5.3.1.3 |
llc2 OBJECT IDENTIFIER .1.3.6.1.4.1.173.7.6 |
nlLlc2HostTableA Table to define LLC2 host entries. SEQUENCE OF NlLlc2HostEntry .1.3.6.1.4.1.173.7.6.1 |
nlLlc2HostEntryAn LLC2 Host entry containing objects relating to
LLC2 hosts. NlLlc2HostEntry .1.3.6.1.4.1.173.7.6.1.1 |
nlLlc2HostIndexLLC2 Host Indexro INTEGER .1.3.6.1.4.1.173.7.6.1.1.1 |
nlLlc2HostMACAddressThe LLC2 Host MAC Address.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.173.7.6.1.1.2 |
nlLlc2HostSessionTypeThe mode in which the Host is operatingrw Enumeration .1.3.6.1.4.1.173.7.6.1.1.3 |
nlLlc2HostT1ReplyTimerReply Timer used to detect a failure of the Remote node.rw TimeInterval .1.3.6.1.4.1.173.7.6.1.1.4 |
nlLlc2HostT2RecvAckTimerReceive Ack Timer used to delay sending an
acknowledgement of a received information LPDU.rw TimeInterval .1.3.6.1.4.1.173.7.6.1.1.5 |
nlLlc2HostTiInactivityTimerTimer used to detect inoperative condition of the
remote link station or transmission medium.rw TimeInterval .1.3.6.1.4.1.173.7.6.1.1.6 |
nlLlc2HostN3NumberLPDUsThe number of Information LPDUs that need to be received
before an acknowledgement is sent.rw INTEGER .1.3.6.1.4.1.173.7.6.1.1.7 |
nlLlc2HostTwNumberOutstandingMaximum number of sequentially numbered information
LPDUs that can be outstanding at any time.rw INTEGER .1.3.6.1.4.1.173.7.6.1.1.8 |
nlLlc2HostN2ExpiredT1LPDUCountMaximum number of LPDU retransmissions occur following
the expiration of Timer T1.rw INTEGER .1.3.6.1.4.1.173.7.6.1.1.9 |
nlLlc2HostPriorityTraffic priorities within the node.rw INTEGER .1.3.6.1.4.1.173.7.6.1.1.10 |
nlLlc2HostBAGBandwidth Allocation group to which the LLC2 Host belongs.
This object is read-only. Bandwidth allocation groups do not apply
to LLC2 hosts.ro INTEGER .1.3.6.1.4.1.173.7.6.1.1.11 |
nlLlc2HostRoutingSubscriberIdLLC2 hosts Routing Subscriber Idrw NlSubscriberAddress .1.3.6.1.4.1.173.7.6.1.1.12 |
nlLlc2HostSrcMACAddressMaskLLC2 Host's Source MAC Address Maskrw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.173.7.6.1.1.13 |
nlLlc2HostAccessSpecifies different type(s) of interface(s) that can be
used for connections to a terminated host session.ro Enumeration .1.3.6.1.4.1.173.7.6.1.1.14 |
nlLlc2HostRowStatusRow status convention for LLC2 Host entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.173.7.6.1.1.15 |
nlLlc2HostInterfaceLLC2 interface number associated with this host entry, always
300 for non-FRX7000.ro INTEGER .1.3.6.1.4.1.173.7.6.1.1.16 |
nlLlc2HostGroupTraffic group associated with LLC2 interface, always 1 for
non-FRX7000.ro INTEGER .1.3.6.1.4.1.173.7.6.1.1.17 |
nlLlc2TermConnectionTableA Table to describe LLC2 Terminated Host Connections. SEQUENCE OF NlLlc2TermConnectionEntry .1.3.6.1.4.1.173.7.6.2 |
nlLlc2TermConnectionEntryAn LLC2 Terminated Host Connection entry containing
objects relating to LLC2 terminated host connections. NlLlc2TermConnectionEntry .1.3.6.1.4.1.173.7.6.2.1 |
nlLlc2TermConnectionSequenceLLC2 Host connection Sequence numberro INTEGER .1.3.6.1.4.1.173.7.6.2.1.1 |
nlLlc2TermConnectionHSAPService Access point used to connect to the Hostrw INTEGER .1.3.6.1.4.1.173.7.6.2.1.2 |
nlLlc2TermConnectionLocalSubscriberIdLLC2 Host Connection's Local Subscriber Idrw NlSubscriberAddress .1.3.6.1.4.1.173.7.6.2.1.3 |
nlLlc2TermConnectionRemoteSubscriberIdLLC2 Host Connection's Remote Subscriber Idrw NlSubscriberAddress .1.3.6.1.4.1.173.7.6.2.1.4 |
nlLlc2TermConnectionRowStatusThis variable is used to manage the creation and deletion
of conceptual rows in the nlLlc2TermConnectionTable and follows the
SNMPv2 RowStatus conventions by supporting the following values:
- `active', which indicates that the conceptual row is
available for use by the managed device. For a management
protocol set operation, a genErr response is returned when
the row does not exist.
- `createAndGo', which is supplied by a management
station wishing to create a new instance of a
conceptual row and to have its status automatically set
to active, making it available for use by the managed
device. For a management protocol set operation, a
genErr response is returned when the row already exists.
- `destroy', which is supplied by a management station
wishing to delete all of the instances associated with
an existing conceptual row.
Note that all of the above values may be specified in a
management protocol set operation, and only the 'active'
value will be returned in response to a management protocol
retrieval operation. For a management protocol set operation,
if other variable bindings are included in the same PDU, then
a genErr response is returned.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.173.7.6.2.1.5 |
nlLlc2OrigConnectionTableA Table to describe LLC2 Originated Host Connections. SEQUENCE OF NlLlc2OrigConnectionEntry .1.3.6.1.4.1.173.7.6.3 |
nlLlc2OrigConnectionEntryAn LLC2 Originated Host Connection entry containing
objects relating to LLC2 originated host connections. NlLlc2OrigConnectionEntry .1.3.6.1.4.1.173.7.6.3.1 |
nlLlc2OrigConnectionSequenceLLC2 Host connection Sequence numberro INTEGER .1.3.6.1.4.1.173.7.6.3.1.1 |
nlLlc2OrigConnectionHSAPService Access point used to connect to the Hostrw INTEGER .1.3.6.1.4.1.173.7.6.3.1.2 |
nlLlc2OrigConnectionTypeSpecifies Remote subscriber device typerw Enumeration .1.3.6.1.4.1.173.7.6.3.1.3 |
nlLlc2OrigConnectionLocalSubscriberIdLLC2 Host Connection's Local Subscriber Idrw NlSubscriberAddress .1.3.6.1.4.1.173.7.6.3.1.4 |
nlLlc2OrigConnectionRemoteSubscriberIdLLC2 Host Connection's Remote Subscriber Idrw NlSubscriberAddress .1.3.6.1.4.1.173.7.6.3.1.5 |
nlLlc2OrigConnectionIDBLKThis field is obsoletero INTEGER .1.3.6.1.4.1.173.7.6.3.1.6 |
nlLlc2OrigConnectionIDNUMThis field is obsoletero INTEGER .1.3.6.1.4.1.173.7.6.3.1.7 |
nlLlc2OrigConnectionMAXDATAThis field is obsoletero INTEGER .1.3.6.1.4.1.173.7.6.3.1.8 |
nlLlc2OrigConnectionMAXINThis field is obsoletero INTEGER .1.3.6.1.4.1.173.7.6.3.1.9 |
nlLlc2OrigConnectionRowStatusThis variable is used to manage the creation and deletion
of conceptual rows in the nlLlc2OrigConnectionTable and follows the
SNMPv2 RowStatus conventions by supporting the following values:
- `active', which indicates that the conceptual row is
available for use by the managed device. For a management
protocol set operation, a genErr response is returned when
the row does not exist.
- `createAndGo', which is supplied by a management
station wishing to create a new instance of a
conceptual row and to have its status automatically set
to active, making it available for use by the managed
device. For a management protocol set operation, a
genErr response is returned when the row already exists.
- `destroy', which is supplied by a management station
wishing to delete all of the instances associated with
an existing conceptual row.
Note that all of the above values may be specified in a
management protocol set operation, and only the 'active'
value will be returned in response to a management protocol
retrieval operation. For a management protocol set operation,
if other variable bindings are included in the same PDU, then
a genErr response is returned.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.173.7.6.3.1.10 |
nlLlc2NextHostNumberThe host number to be used for the next created
host record, always 1 on non-FRX7000.ro INTEGER .1.3.6.1.4.1.173.7.6.4 |
status OBJECT IDENTIFIER .1.3.6.1.4.1.173.7.7 |
pinStatusTableA Table to describe the status of each pin on a
physical port. This table is indexed by RLP and Port SEQUENCE OF PortPinEntry .1.3.6.1.4.1.173.7.7.4 |
portPinEntryA port pin entry containing objects relating to ports. PortPinEntry .1.3.6.1.4.1.173.7.7.4.1 |
portPinRlpThe RLP number on the nodero INTEGER .1.3.6.1.4.1.173.7.7.4.1.1 |
portPinPortThe Port number on the RLP. Port numbers 0-7 are
known to be physical ports.ro INTEGER .1.3.6.1.4.1.173.7.7.4.1.2 |
portPinStatusThe status of all pins for this physical port. There
is one octet value for each of the pins. Each octet value is defined
as follows:
00 = unknown
01 = active
02 = inactive
03 = unusedro OCTET STRING .1.3.6.1.4.1.173.7.7.4.1.3 |
statistics OBJECT IDENTIFIER .1.3.6.1.4.1.173.7.8 |
statGroup OBJECT IDENTIFIER .1.3.6.1.4.1.173.7.8.1 |
rlpStatsTableA Table to describe Statistics on each RLP SEQUENCE OF RlpStatsEntry .1.3.6.1.4.1.173.7.8.1.2 |
rlpStatsEntryAn RLP statistics entry containing objects relating
to RLP statistics. RlpStatsEntry .1.3.6.1.4.1.173.7.8.1.2.1 |
rlpStatsIndexThe RLP numberro INTEGER .1.3.6.1.4.1.173.7.8.1.2.1.1 |
rlpStatsQMessagesThe number of frames queued on the RLPro Counter .1.3.6.1.4.1.173.7.8.1.2.1.2 |
rlpStatsUsedBuffersThe percentage of total buffers available being used at
the moment of inquiryro Counter .1.3.6.1.4.1.173.7.8.1.2.1.3 |
rlpStatsInFramesThe number of frames received.ro Counter .1.3.6.1.4.1.173.7.8.1.2.1.4 |
rlpStatsOutFramesThe number of frames transmitted.ro Counter .1.3.6.1.4.1.173.7.8.1.2.1.5 |
rlpStatsFrameRejectsThe number of frames rejected.ro Counter .1.3.6.1.4.1.173.7.8.1.2.1.6 |
rlpStatsFrameRetransmitsThe number of frames retransmitted . If
this value is consistently greater than zero and there are no other
problems, then increase the retransmission parameter.ro Counter .1.3.6.1.4.1.173.7.8.1.2.1.7 |
portStatsTableA Table to describe Statistics on each RLP SEQUENCE OF PortStatsEntry .1.3.6.1.4.1.173.7.8.1.3 |
portStatsEntryA port statistics entry containing objects relating
to port statistics. PortStatsEntry .1.3.6.1.4.1.173.7.8.1.3.1 |
portStatsRlpIndexThe RLP numberro INTEGER .1.3.6.1.4.1.173.7.8.1.3.1.1 |
portStatsIndexThe Port numberro INTEGER .1.3.6.1.4.1.173.7.8.1.3.1.2 |
portStatsInFramesThe number of frames received.ro Counter .1.3.6.1.4.1.173.7.8.1.3.1.3 |
portStatsOutFramesThe number of frames transmitted.ro Counter .1.3.6.1.4.1.173.7.8.1.3.1.4 |
portStatsFrameRetransThe number of frames retransmitted.ro Counter .1.3.6.1.4.1.173.7.8.1.3.1.5 |
portStatsFCSErrorsThe number of Frame Check Sequence (FCS) errors.
A value consistently greater than zero indicates line probelms.ro Counter .1.3.6.1.4.1.173.7.8.1.3.1.6 |
portStatsLogicalRejectsThe sum of Rejects and Frame Rejects.
A value consistently greater than zero indicates line probelms.ro Counter .1.3.6.1.4.1.173.7.8.1.3.1.7 |
portStatsInPercentUtilsThe ratio of non-flag characters to total characters
being received by the port.ro Counter .1.3.6.1.4.1.173.7.8.1.3.1.8 |
portStatsOutPercentUtilsThe ration of non-flag characters to total characters
being transmitted by the port.ro Counter .1.3.6.1.4.1.173.7.8.1.3.1.9 |
statFrame OBJECT IDENTIFIER .1.3.6.1.4.1.173.7.8.1.4 |
frStatsTableA Table to describe Frame Relay Frame Level Statistics on each Port SEQUENCE OF FrStatsEntry .1.3.6.1.4.1.173.7.8.1.4.1 |
frStatsEntryA frame relay port statistics entry containing objects
relating to frame relay port statistics. FrStatsEntry .1.3.6.1.4.1.173.7.8.1.4.1.1 |
frStatsRlpIndexThe RLP Number.ro INTEGER .1.3.6.1.4.1.173.7.8.1.4.1.1.1 |
frStatsPortIndexThe Port number.ro INTEGER .1.3.6.1.4.1.173.7.8.1.4.1.1.2 |
frStatsTxDEFramesThe number of frames transmitted on the port with the
Discard Eligibility bit set.ro Counter .1.3.6.1.4.1.173.7.8.1.4.1.1.3 |
frStatsRxDEFramesThe number of frames received on the port with the discard
eligibility bit set.ro Counter .1.3.6.1.4.1.173.7.8.1.4.1.1.4 |
frStatsTxFECNFramesThe of number of frames transmitted on the port with FECN.ro Counter .1.3.6.1.4.1.173.7.8.1.4.1.1.5 |
frStatsRxFECNFramesThe number of frames received on the port with FECN.ro Counter .1.3.6.1.4.1.173.7.8.1.4.1.1.6 |
frStatsTxBECNFramesThe number of frames transmitted on the port with BECN.ro Counter .1.3.6.1.4.1.173.7.8.1.4.1.1.7 |
frStatsRxBECNFramesThe number of frames received on the port with BECN.ro Counter .1.3.6.1.4.1.173.7.8.1.4.1.1.8 |
frStatsTxLMIFramesThe number of LMI frames transmitted on the port.ro Counter .1.3.6.1.4.1.173.7.8.1.4.1.1.9 |
frStatsRxLMIFramesThe number of LMI frames received on the port.ro Counter .1.3.6.1.4.1.173.7.8.1.4.1.1.10 |
frStatsTxANXDFramesThe number of AnnexD frames transmitted on the portro Counter .1.3.6.1.4.1.173.7.8.1.4.1.1.11 |
frStatsRxANXDFramesThe number of AnnexD frames received on the portro Counter .1.3.6.1.4.1.173.7.8.1.4.1.1.12 |
frStatsTotDiscFramesThe total number of discarded frames on the port.ro Counter .1.3.6.1.4.1.173.7.8.1.4.1.1.13 |
x25TxStatsTableA Table to describe X25 Frame Level Txmit Statistics on each Port SEQUENCE OF X25TxStatsEntry .1.3.6.1.4.1.173.7.8.1.4.2 |
x25TxStatsEntryAn X25 frame level transmit statistics entry containing
objects relating to x25 frame level transmit statistics. X25TxStatsEntry .1.3.6.1.4.1.173.7.8.1.4.2.1 |
x25TxRlpIndexThe RLP Number.ro INTEGER .1.3.6.1.4.1.173.7.8.1.4.2.1.1 |
x25TxPortIndexThe Port number.ro INTEGER .1.3.6.1.4.1.173.7.8.1.4.2.1.2 |
x25TxSABMFramesThe number of SABM's transmitted on the port.ro Counter .1.3.6.1.4.1.173.7.8.1.4.2.1.3 |
x25TxUAFramesThe number of UA Frames transmitted on the port.ro Counter .1.3.6.1.4.1.173.7.8.1.4.2.1.4 |
x25TxDISCFramesThe number of DISC Frames transmitted on the port.ro Counter .1.3.6.1.4.1.173.7.8.1.4.2.1.5 |
x25TxDMFramesThe number of DM frames transmitted on the port.ro Counter .1.3.6.1.4.1.173.7.8.1.4.2.1.6 |
x25TxFRMRFramesThe of Number of FRMR frames transmitted on the port.ro Counter .1.3.6.1.4.1.173.7.8.1.4.2.1.7 |
x25TxREJFramesThe number of Reject Frames transmitted on the port.ro Counter .1.3.6.1.4.1.173.7.8.1.4.2.1.8 |
x25TxRRFramesThe number of RR frames transmitted on the port.ro Counter .1.3.6.1.4.1.173.7.8.1.4.2.1.9 |
x25TxRNRFramesThe number of RNR Frames transmitted on the port.ro Counter .1.3.6.1.4.1.173.7.8.1.4.2.1.10 |
x25TxINFOFramesThe number of INFO Frames transmitted on the portro Counter .1.3.6.1.4.1.173.7.8.1.4.2.1.11 |
x25RxStatsTableA Table to describe X25 Frame Level Rxmit Statistics on each Port SEQUENCE OF X25RxStatsEntry .1.3.6.1.4.1.173.7.8.1.4.3 |
x25RxStatsEntryAn X25 frame level receive statistics entry containing
objects relating to x25 frame level receive statistics. X25RxStatsEntry .1.3.6.1.4.1.173.7.8.1.4.3.1 |
x25RxRlpIndexThe RLP Number.ro INTEGER .1.3.6.1.4.1.173.7.8.1.4.3.1.1 |
x25RxPortIndexThe Port number.ro INTEGER .1.3.6.1.4.1.173.7.8.1.4.3.1.2 |
x25RxSABMFramesThe number of SABM's received on the port.ro Counter .1.3.6.1.4.1.173.7.8.1.4.3.1.3 |
x25RxUAFramesThe number of UA Frames received on the port.ro Counter .1.3.6.1.4.1.173.7.8.1.4.3.1.4 |
x25RxDISCFramesThe number of DISC Frames received on the port.ro Counter .1.3.6.1.4.1.173.7.8.1.4.3.1.5 |
x25RxDMFramesThe number of DM frames received on the port.ro Counter .1.3.6.1.4.1.173.7.8.1.4.3.1.6 |
x25RxFRMRFramesThe of Number of FRMR frames received on the port.ro Counter .1.3.6.1.4.1.173.7.8.1.4.3.1.7 |
x25RxREJFramesThe number of Reject Frames received on the port.ro Counter .1.3.6.1.4.1.173.7.8.1.4.3.1.8 |
x25RxRRFramesThe number of RR frames received on the port.ro Counter .1.3.6.1.4.1.173.7.8.1.4.3.1.9 |
x25RxRNRFramesThe number of RNR Frames received on the port.ro Counter .1.3.6.1.4.1.173.7.8.1.4.3.1.10 |
x25RxINFOFramesThe number of INFO Frames received on the portro Counter .1.3.6.1.4.1.173.7.8.1.4.3.1.11 |
statBag OBJECT IDENTIFIER .1.3.6.1.4.1.173.7.8.1.5 |
statIp OBJECT IDENTIFIER .1.3.6.1.4.1.173.7.8.1.6 |
statT1 OBJECT IDENTIFIER .1.3.6.1.4.1.173.7.8.1.7 |
t1StatsTableA Table to describe T1 Statistics. SEQUENCE OF T1StatsEntry .1.3.6.1.4.1.173.7.8.1.7.1 |
t1StatsEntryA T1 port statistics entry containing objects relating
to T1 port statistics. T1StatsEntry .1.3.6.1.4.1.173.7.8.1.7.1.1 |
t1StatsRlpIndexThe RLP Number.ro INTEGER .1.3.6.1.4.1.173.7.8.1.7.1.1.1 |
t1StatsPortIndexThe Port Number.ro INTEGER .1.3.6.1.4.1.173.7.8.1.7.1.1.2 |
t1StatsRcvFramesTotal received frames.ro Counter .1.3.6.1.4.1.173.7.8.1.7.1.1.3 |
t1StatsXmitFramesTotal transmitted frames.ro Counter .1.3.6.1.4.1.173.7.8.1.7.1.1.4 |
t1StatsLCVCntLine code violation count.ro Counter .1.3.6.1.4.1.173.7.8.1.7.1.1.5 |
t1StatsPCVRErrsPCVR Bit error count.ro Counter .1.3.6.1.4.1.173.7.8.1.7.1.1.6 |
t1StatsOOSCntMultiframe out of sync count.ro Counter .1.3.6.1.4.1.173.7.8.1.7.1.1.7 |
t1StatsBlueAlarmsBlue alarm count.ro Counter .1.3.6.1.4.1.173.7.8.1.7.1.1.8 |
t1StatsYellowAlarmsYellow alarm count.ro Counter .1.3.6.1.4.1.173.7.8.1.7.1.1.9 |
t1StatsRedAlarmsRed alarm count.ro Counter .1.3.6.1.4.1.173.7.8.1.7.1.1.10 |
t1StatsRcvUsageReceive port utilization.ro Counter .1.3.6.1.4.1.173.7.8.1.7.1.1.11 |
t1StatsXmitUsageTransmit port utilization.ro Counter .1.3.6.1.4.1.173.7.8.1.7.1.1.12 |
t1StatsXmitAbortFramesTotal aborted transmit frames.ro Counter .1.3.6.1.4.1.173.7.8.1.7.1.1.13 |
t1StatsRcvAbortFramesTotal aborted receive frames.ro Counter .1.3.6.1.4.1.173.7.8.1.7.1.1.14 |
t1StatsRcvOverrunsTotal receive overruns.ro Counter .1.3.6.1.4.1.173.7.8.1.7.1.1.15 |
t1StatsRcvErrorsTotal bad receives.ro Counter .1.3.6.1.4.1.173.7.8.1.7.1.1.16 |
t1StatsRcvChannelErrorsTotal bad receives.ro Counter .1.3.6.1.4.1.173.7.8.1.7.1.1.17 |
statDS0A OBJECT IDENTIFIER .1.3.6.1.4.1.173.7.8.1.8 |
ds0aStatsTableA Table to describe DS0A Statistics. SEQUENCE OF DS0AStatsEntry .1.3.6.1.4.1.173.7.8.1.8.1 |
ds0aStatsEntryA DS0A port statistics entry containing objects relating
to DS0A port statistics. DS0AStatsEntry .1.3.6.1.4.1.173.7.8.1.8.1.1 |
ds0aStatsRlpIndexThe RLP Number.ro INTEGER .1.3.6.1.4.1.173.7.8.1.8.1.1.1 |
ds0aStatsPortIndexThe Port Number.ro INTEGER .1.3.6.1.4.1.173.7.8.1.8.1.1.2 |
ds0aStatsChannelIndexThe Channel Number.ro INTEGER .1.3.6.1.4.1.173.7.8.1.8.1.1.3 |
ds0aStatsXmitFramesTotal transmitted frames.ro Counter .1.3.6.1.4.1.173.7.8.1.8.1.1.4 |
ds0aStatsRcvFramesTotal received frames.ro Counter .1.3.6.1.4.1.173.7.8.1.8.1.1.5 |
ds0aStatsRcvAbortFramesTotal receive aborted frames.ro Counter .1.3.6.1.4.1.173.7.8.1.8.1.1.6 |
ds0aStatsRcvOverrunsTotal receive overruns.ro Counter .1.3.6.1.4.1.173.7.8.1.8.1.1.7 |
ds0aStatsRcvErrorsTotal receive errors.ro Counter .1.3.6.1.4.1.173.7.8.1.8.1.1.8 |
statVoice OBJECT IDENTIFIER .1.3.6.1.4.1.173.7.8.1.9 |
voiceStatsTableA Table to describe Voice over Frame Relay Statistics. SEQUENCE OF VoiceStatsEntry .1.3.6.1.4.1.173.7.8.1.9.1 |
voiceStatsEntryA voice port statistics entry containing objects relating
to voice port statistics. VoiceStatsEntry .1.3.6.1.4.1.173.7.8.1.9.1.1 |
voiceStatsRlpIndexThe RLP Number.ro INTEGER .1.3.6.1.4.1.173.7.8.1.9.1.1.1 |
voiceStatsPortIndexThe Port Number.ro INTEGER .1.3.6.1.4.1.173.7.8.1.9.1.1.2 |
voiceStatsRxCallsThe Number of Calls Received from the Network.ro Counter .1.3.6.1.4.1.173.7.8.1.9.1.1.3 |
voiceStatsTxCallsThe Number of Calls Transmitted to the Network.ro Counter .1.3.6.1.4.1.173.7.8.1.9.1.1.4 |
voiceStatsRxCallsAcceptsThe Number of Call Accepts Received from the Network.ro Counter .1.3.6.1.4.1.173.7.8.1.9.1.1.5 |
voiceStatsTxCallsAcceptsThe Number of Call Accepts Transmitted to the Network.ro Counter .1.3.6.1.4.1.173.7.8.1.9.1.1.6 |
voiceStatsRxClearsThe Number of Call Receives cleared.ro Counter .1.3.6.1.4.1.173.7.8.1.9.1.1.7 |
voiceStatsTxClearsThe Number of Call Transmitts cleared.ro Counter .1.3.6.1.4.1.173.7.8.1.9.1.1.8 |
voiceStatsBusyCallsThe Number of calls which received Busy indication.ro Counter .1.3.6.1.4.1.173.7.8.1.9.1.1.9 |
voiceStatsCallTimeoutsThe Number of calls which transmitted time-out to the network.ro Counter .1.3.6.1.4.1.173.7.8.1.9.1.1.10 |
voiceStatsRxCongestionsThe number of congestion management frames Received.ro Counter .1.3.6.1.4.1.173.7.8.1.9.1.1.11 |
voiceStatsTxCongestionsThe number of congestion management frames Transmitted.ro Counter .1.3.6.1.4.1.173.7.8.1.9.1.1.12 |
statThresh OBJECT IDENTIFIER .1.3.6.1.4.1.173.7.8.2 |
rlpThreshTableA Table to describe Statistic thresholds on each RLP SEQUENCE OF RlpThreshEntry .1.3.6.1.4.1.173.7.8.2.1 |
rlpThreshEntryAn RLP statistics threshold entry containing objects
relating to RLP statistics thresholds. RlpThreshEntry .1.3.6.1.4.1.173.7.8.2.1.1 |
rlpThreshRlpIndexThe RLP Number.ro INTEGER .1.3.6.1.4.1.173.7.8.2.1.1.1 |
rlpThreshPercntBufInUseThe threshold for Percent of Buffers in use on the RLPro INTEGER .1.3.6.1.4.1.173.7.8.2.1.1.2 |
rlpThreshMsgQueueLenThe threshold for Percent of Buffers in use on the RLPro INTEGER .1.3.6.1.4.1.173.7.8.2.1.1.3 |
rlpThreshRxFramesPerSecThe threshold for Rcvd frames per second on the RLPro INTEGER .1.3.6.1.4.1.173.7.8.2.1.1.4 |
rlpThreshTxFramesPerSecThe threshold for Txmitted frames per second on the RLPro INTEGER .1.3.6.1.4.1.173.7.8.2.1.1.5 |
rlpThreshRejFramesPerSecThe threshold for Rejected Frames per second on the RLPro INTEGER .1.3.6.1.4.1.173.7.8.2.1.1.6 |
rlpThreshRtxFramesPerSecThe threshold for Retransmitted frames per second on the RLPro INTEGER .1.3.6.1.4.1.173.7.8.2.1.1.7 |
portThreshTableA Table to describe Statistic thresholds on each port SEQUENCE OF PortThreshEntry .1.3.6.1.4.1.173.7.8.2.2 |
portThreshEntryA port statistics threshold entry containing objects
relating to port statistics thresholds. PortThreshEntry .1.3.6.1.4.1.173.7.8.2.2.1 |
portThreshRlpIndexThe RLP Number.ro INTEGER .1.3.6.1.4.1.173.7.8.2.2.1.1 |
portThreshIndexThe Port Number.ro INTEGER .1.3.6.1.4.1.173.7.8.2.2.1.2 |
portThreshRxFramesPerSecThe threshold for Rcvd frames per second on the port.ro INTEGER .1.3.6.1.4.1.173.7.8.2.2.1.3 |
portThreshTxFramesPerSecThe threshold for Txmitted frames per second on the port.ro INTEGER .1.3.6.1.4.1.173.7.8.2.2.1.4 |
portThreshRtxFramesPerSecThe threshold for Retransmitted frames per second on the port.ro INTEGER .1.3.6.1.4.1.173.7.8.2.2.1.5 |
portThreshFCSErrPerSecThe threshold for FCS errors per second on the port.ro INTEGER .1.3.6.1.4.1.173.7.8.2.2.1.6 |
portThreshLogRejPerSecThe threshold for Logical Rejects per second on the port.ro INTEGER .1.3.6.1.4.1.173.7.8.2.2.1.7 |
portThreshTxErrorRatioThe threshold for Txmit error ratio on the port.ro INTEGER .1.3.6.1.4.1.173.7.8.2.2.1.8 |
portThreshRxErrorRatioThe threshold for Rcv error ratio on the port.ro INTEGER .1.3.6.1.4.1.173.7.8.2.2.1.9 |
portThreshTxPercentUtlThe threshold for Txmit percent utilization on the port.ro INTEGER .1.3.6.1.4.1.173.7.8.2.2.1.10 |
portThreshRxPercentUtlThe threshold for Rcv percent utilization on the port.ro INTEGER .1.3.6.1.4.1.173.7.8.2.2.1.11 |
bridge OBJECT IDENTIFIER .1.3.6.1.4.1.173.7.9 |
bridgeAdminVirtualLANIDLAN id inserted into token ring RIF field representing
internal virtual ring, for LLC2 or bridged trafficrw INTEGER .1.3.6.1.4.1.173.7.9.1 |
bridgeOperVirtualLANIDLAN id inserted into token ring RIF field representing
internal virtual ring, for LLC2 or bridged trafficro INTEGER .1.3.6.1.4.1.173.7.9.2 |
bridgeEnabledWhen yes the spanning tree algorithm is in effect and all
traffic types may be bridged. When no only llc/2 terminated
traffic is allowed on bridge interfaces.rw Enumeration .1.3.6.1.4.1.173.7.9.3 |
bridgeMaxSizeForwardingTableNumber of entries allowed in the bridge forwarding
tablerw INTEGER .1.3.6.1.4.1.173.7.9.4 |
bridgeIPEnabledWhen yes, and BRIDGING ENABLED, IP traffic will be bridged,
otherwise IP traffic will be routed.rw Enumeration .1.3.6.1.4.1.173.7.9.5 |
bridgeIPXEnabledWhen yes, and BRIDGING ENABLED, IPX traffic will be bridged,
otherwise IPX traffic will be routed.rw Enumeration .1.3.6.1.4.1.173.7.9.6 |
bridgeAdminSRBIDbridge ID to be inserted into token ring RIF field,
this bridgerw INTEGER .1.3.6.1.4.1.173.7.9.7 |
bridgeOperSRBIDbridge ID to be inserted into token ring RIF field,
this bridgero INTEGER .1.3.6.1.4.1.173.7.9.8 |
bridgeDefaultEthernetFrameTypedefault frame type to be used when
forwarding traffic on ethernet interfaces.rw Enumeration .1.3.6.1.4.1.173.7.9.9 |
ipNl OBJECT IDENTIFIER .1.3.6.1.4.1.173.7.11 |
nlIpDefaultRIPVersionThe version of RIP that will be used by IP.rw Enumeration .1.3.6.1.4.1.173.7.11.1 |
voice OBJECT IDENTIFIER .1.3.6.1.4.1.173.7.12 |
voiceSystemVoiceNodeNumThe number that identifies this node.rw INTEGER .1.3.6.1.4.1.173.7.12.1 |
voiceSystemRingVolFreqThe frequency and voltage of the telephone ring circuit.
In two wire OPX mode, the node provides ring voltage to
the telephone when it is called by a remote unit.rw Enumeration .1.3.6.1.4.1.173.7.12.2 |
voiceSystemCountryCodeThe telephone dialing prefix code that identifies
the country in which the node is installed.rw INTEGER .1.3.6.1.4.1.173.7.12.3 |
voiceSystemDialDigitsThe number of digits that will be used in the speed
dialing scheme, as well as the number of digits one
can specify for the Auto Dial feature. This requires
rebooting for the change to take effect.rw INTEGER .1.3.6.1.4.1.173.7.12.4 |
voiceSystemVoiceRatesMinThe minimum operating rate of all voice channels when
congestion occurs.rw Enumeration .1.3.6.1.4.1.173.7.12.5 |
voiceSystemVoiceRatesMaxThe maximum operating digitization rate of all voice
channels when there is no congestion.rw Enumeration .1.3.6.1.4.1.173.7.12.6 |
voiceSystemExtDialDigitsThe number of extended dial digits that can be defined
in the speed map table and/or entered by the user of
attached equipment as part of a dial string. This requires
rebooting for the change to take effect.rw INTEGER .1.3.6.1.4.1.173.7.12.7 |
voiceSpeedDialTableA list of speed-dial numbers. SEQUENCE OF VoiceSpeedDialEntry .1.3.6.1.4.1.173.7.12.8 |
voiceSpeedDialEntryA Voice Speed Dial entry containing objects relating to
the speed-dial number that are configurable by the user. VoiceSpeedDialEntry .1.3.6.1.4.1.173.7.12.8.1 |
voiceSpeedDialDigitsThe speed-dial number. A question mark wildcard can be used
for any digit, and an asterisk wildcard can be used for any
number of digits.ro OCTET STRING .1.3.6.1.4.1.173.7.12.8.1.1 |
voiceSpeedDialLongDialMapThe number for which the speed-dial number is a shortcut.rw OCTET STRING .1.3.6.1.4.1.173.7.12.8.1.2 |
voiceSpeedDialExtDialStrThe extended set of digits that will be forwarded with the
call if portVoiceOperExtDigitsSource in the physical port
record is set to Map.rw OCTET STRING .1.3.6.1.4.1.173.7.12.8.1.3 |
voiceSpeedDialRowStatusThis variable is used to manage the creation and deletion
of conceptual rows in the voiceSpeedDialTable and follows the
SNMPv2 RowStatus conventions by supporting the following values:
- `active', which indicates that the conceptual row is
available for use by the managed device. For a management
protocol set operation, a genErr response is returned when
the row does not exist.
- `createAndGo', which is supplied by a management
station wishing to create a new instance of a
conceptual row and to have its status automatically set
to active, making it available for use by the managed
device. For a management protocol set operation, a
genErr response is returned when the row already exists.
- `destroy', which is supplied by a management station
wishing to delete all of the instances associated with
an existing conceptual row.
Note that all of the above values may be specified in a
management protocol set operation, and only the 'active'
value will be returned in response to a management protocol
retrieval operation. For a management protocol set operation,
if other variable bindings are included in the same PDU, then
a genErr response is returned.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.173.7.12.8.1.4 |