NETGEAR-SWITCHING-MIB
AI MIB Summary
The NETGEAR-SWITCHING-MIB provides vendor-specific extensions for monitoring and managing Layer 2 switching functions on Netgear network switches, including port status, MAC address table entries, and VLAN configurations. It enables SNMP-based retrieval of proprietary switching metrics not covered by standard IETF MIBs to facilitate granular fault isolation and traffic analysis within Netgear-managed infrastructure.
The Netgear Private MIB for Switching
Main OID:
agentSwitching.1.3.6.1.4.1.4526.11.1
468
Objects
Active
Status
8
Dependencies
Imported Objects
Objects
468 total| Object Name |
|---|
agentSwitchingThe Netgear Private MIB for Switching MODULE-IDENTITY .1.3.6.1.4.1.4526.11.1 |
agentSwitchingTraps OBJECT IDENTIFIER .1.3.6.1.4.1.4526.11.1.0 |
multipleUsersTrapThis trap is sent when more than one user is logged in with
administrative access. Only applies to CLI interface. NOTIFICATION-TYPE .1.3.6.1.4.1.4526.11.1.0.1 |
broadcastStormStartTrapThis trap is sent when a broadcast storm is detected. NOTIFICATION-TYPE .1.3.6.1.4.1.4526.11.1.0.2 |
broadcastStormEndTrapThis trap is sent when a broadcast storm is no longer
detected. NOTIFICATION-TYPE .1.3.6.1.4.1.4526.11.1.0.3 |
linkFailureTrap NOTIFICATION-TYPE .1.3.6.1.4.1.4526.11.1.0.4 |
vlanRequestFailureTrap NOTIFICATION-TYPE .1.3.6.1.4.1.4526.11.1.0.5 |
vlanDeleteLastTrapTrap is sent when attempting to delete the last configured VLAN
or the Default VLAN. NOTIFICATION-TYPE .1.3.6.1.4.1.4526.11.1.0.6 |
vlanDefaultCfgFailureTrapTrap is sent if there are failures in resetting VLAN
configuration to defaults. NOTIFICATION-TYPE .1.3.6.1.4.1.4526.11.1.0.7 |
vlanRestoreFailureTrap NOTIFICATION-TYPE .1.3.6.1.4.1.4526.11.1.0.8 |
fanFailureTrap NOTIFICATION-TYPE .1.3.6.1.4.1.4526.11.1.0.9 |
stpInstanceNewRootTrapTrap is sent when this machine is a new STP Root when there is more
than one STP instance. NOTIFICATION-TYPE .1.3.6.1.4.1.4526.11.1.0.10 |
stpInstanceTopologyChangeTrapTrap is sent when there is a STP topology change when there is more
than one STP instance. NOTIFICATION-TYPE .1.3.6.1.4.1.4526.11.1.0.11 |
powerSupplyStatusChangeTrap NOTIFICATION-TYPE .1.3.6.1.4.1.4526.11.1.0.12 |
failedUserLoginTrapTrap is sent when a user fails to authenticate via the CLI or Web
interfaces. NOTIFICATION-TYPE .1.3.6.1.4.1.4526.11.1.0.13 |
userLockoutTrapTrap is sent when a user account is locked due to consecutive failed login attempts via the CLI or Web
interfaces beyond the allowed limit. NOTIFICATION-TYPE .1.3.6.1.4.1.4526.11.1.0.14 |
macAddrLearnTrapTrap is sent when L2 MAC address is learned i.e when entry is added to FDB. NOTIFICATION-TYPE .1.3.6.1.4.1.4526.11.1.0.15 |
macAddrAgeoutTrapTrap is sent when L2 MAC address is agedout i.e when entry is removed from FDB. NOTIFICATION-TYPE .1.3.6.1.4.1.4526.11.1.0.16 |
agentInfoGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4526.11.1.1 |
agentInventoryGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4526.11.1.1.1 |
agentInventorySysDescriptionThe switch's Inventory system description.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4526.11.1.1.1.1 |
agentInventoryMachineTypeType of the Machine used in the Switchro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4526.11.1.1.1.2 |
agentInventoryMachineModelThe switch's Machine Model.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4526.11.1.1.1.3 |
agentInventorySerialNumberSerial number of the switch.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4526.11.1.1.1.4 |
agentInventoryFRUNumberFRU Number of the switchro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4526.11.1.1.1.5 |
agentInventoryMaintenanceLevelThe switch's Inventory Maintenance Levelro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4526.11.1.1.1.6 |
agentInventoryPartNumberThe switch's Inventory Part Numberro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4526.11.1.1.1.7 |
agentInventoryManufacturerName of the Manufacturer of this unitro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4526.11.1.1.1.8 |
agentInventoryBurnedInMacAddressBurned-In MAC Addressro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.4526.11.1.1.1.9 |
agentInventoryOperatingSystemOperating System running on this unitro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4526.11.1.1.1.10 |
agentInventoryNetworkProcessingDeviceNetwork Processing Device for this unitro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4526.11.1.1.1.11 |
agentInventoryAdditionalPackagesLists additional functional packages available on this unit.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4526.11.1.1.1.12 |
agentInventorySoftwareVersionLists the version of software loaded on this unit.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4526.11.1.1.1.13 |
agentTrapLogGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4526.11.1.1.2 |
agentTrapLogTotalThe total number of traps sent since last reset.ro Integer32 .1.3.6.1.4.1.4526.11.1.1.2.1 |
agentTrapLogTotalSinceLastViewedThe number of traps sent since last viewed.ro Integer32 .1.3.6.1.4.1.4526.11.1.1.2.3 |
agentTrapLogTableAgent Trap Log SEQUENCE OF AgentTrapLogEntry .1.3.6.1.4.1.4526.11.1.1.2.4 |
agentTrapLogEntryAgent trap log entry AgentTrapLogEntry .1.3.6.1.4.1.4526.11.1.1.2.4.1 |
agentTrapLogIndexUnique index of trap entryro Integer32 .1.3.6.1.4.1.4526.11.1.1.2.4.1.1 |
agentTrapLogSystemTimeSystem uptime when trap was sent.
This entry shows how long the system has been up when the trap occurred.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4526.11.1.1.2.4.1.2 |
agentTrapLogTrapDescription of the trap sent.ro OCTET STRING .1.3.6.1.4.1.4526.11.1.1.2.4.1.3 |
agentSupportedMibTableSupported MIB table SEQUENCE OF AgentSupportedMibEntry .1.3.6.1.4.1.4526.11.1.1.3 |
agentSupportedMibEntrySupported MIB entry AgentSupportedMibEntry .1.3.6.1.4.1.4526.11.1.1.3.1 |
agentSupportedMibIndexUnique index of the Supported MIB entryro Integer32 .1.3.6.1.4.1.4526.11.1.1.3.1.1 |
agentSupportedMibNameThe name of the MIB (RFC or IEEE) that is supported.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4526.11.1.1.3.1.2 |
agentSupportedMibDescriptionDescription of the MIB (RFC or IEEE) that is supported.ro OCTET STRING .1.3.6.1.4.1.4526.11.1.1.3.1.3 |
agentConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4526.11.1.2 |
agentCLIConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4526.11.1.2.1 |
agentLoginSessionTableA table of the switch's login session SEQUENCE OF AgentLoginSessionEntry .1.3.6.1.4.1.4526.11.1.2.1.1 |
agentLoginSessionEntryLogin Session Entry AgentLoginSessionEntry .1.3.6.1.4.1.4526.11.1.2.1.1.1 |
agentLoginSessionIndexAgent Login Session Index of the switchro Integer32 .1.3.6.1.4.1.4526.11.1.2.1.1.1.1 |
agentLoginSessionUserNameAgent Login Session UserName of the switchro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4526.11.1.2.1.1.1.2 |
agentLoginSessionIPAddressAgent Login Session IP Address of the switchroobsolete IpAddress .1.3.6.1.4.1.4526.11.1.2.1.1.1.3 |
agentLoginSessionConnectionTypeAgent Login Session Connection Type of the switchro Enumeration .1.3.6.1.4.1.4526.11.1.2.1.1.1.4 |
agentLoginSessionIdleTimeAgent Login Session Idle Time of the switchro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.4526.11.1.2.1.1.1.5 |
agentLoginSessionSessionTimeAgent Login Session Time of the switchro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.4526.11.1.2.1.1.1.6 |
agentLoginSessionStatusStatus of the user.
active(1) - This connection is active.
destroy(6) - Set to this value to disconnect this user.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4526.11.1.2.1.1.1.7 |
agentLoginSessionInetAddressTypeType of address agentLoginSessionInetAddress is returning.
Can be either unknown(0), ipv4(1), or ipv6 (2). Will return
unknown(0) in the case of a serial login.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.4526.11.1.2.1.1.1.8 |
agentLoginSessionInetAddressInet Address of the connecting the user is logging in with.
Will return a zero-length string in the case of a serial login.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.4526.11.1.2.1.1.1.9 |
agentTelnetConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4526.11.1.2.1.2 |
agentTelnetLoginTimeoutTelnet login timeout (minutes)
Config telnet timeout will set the telnet session timeout value.
A session is active as long as the session has not remained idle for
the value set. Specify a value from 1 to 160.
Note: Changing the timeout value for active
sessions does not become effective until the session is reaccessed.
Any keystroke will also activate the new timeout duration.rw Integer32 .1.3.6.1.4.1.4526.11.1.2.1.2.1 |
agentTelnetMaxSessionsMaximum number of Telnet Sessions
Config telnet maxsessions is an integer value from 0 to 5 that specifies the
maximum number of telnet sessions that can be established.
If the value is 0, no Telnet session can be established.rw Integer32 .1.3.6.1.4.1.4526.11.1.2.1.2.2 |
agentTelnetAllowNewModeAllow new telnet sessions (enable or disable)
Config telnet disable means that no new Telnet sessions are to be
established. Any already established session remains active until
the session is ended or an abnormal network error ends it.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.1.2.3 |
agentUserConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4526.11.1.2.1.3 |
agentUserConfigCreateCreate a new user.
When set with a non-empty string, a new user with that name will be created.
This object will only return an empty string.
This string is limited to alpha-numeric strings (uncluding the '-' and '_' characters).rw DisplayString .1.3.6.1.4.1.4526.11.1.2.1.3.1 |
agentUserConfigTableUser Config Table SEQUENCE OF AgentUserConfigEntry .1.3.6.1.4.1.4526.11.1.2.1.3.2 |
agentUserConfigEntryUser Config Entry AgentUserConfigEntry .1.3.6.1.4.1.4526.11.1.2.1.3.2.1 |
agentUserIndexAgent User Config Index Integer32 .1.3.6.1.4.1.4526.11.1.2.1.3.2.1.1 |
agentUserNameAgent User Name.
This string is limited to alpha-numeric strings (including the '-' and '_' characters).ro DisplayString .1.3.6.1.4.1.4526.11.1.2.1.3.2.1.2 |
agentUserPasswordAgent User Password
This object will return an empty string even if a password is set.rw DisplayString .1.3.6.1.4.1.4526.11.1.2.1.3.2.1.3 |
agentUserAccessModeAgent User Access Modero Enumeration .1.3.6.1.4.1.4526.11.1.2.1.3.2.1.4 |
agentUserAuthenticationTypeSNMPv3 User Authentication. The user passsword must be set
to a string greater than or equal to 8 characters for this to be
set to anything but none(1).
none(1) - no authentication used
hmacmd5(1) - Use HMAC-MD5 authentication
hmacsha(1) - Use HMAC-SHA authenticationrw Enumeration .1.3.6.1.4.1.4526.11.1.2.1.3.2.1.6 |
agentUserEncryptionTypeSNMPv3 User Encryption
Can not be set to des(2) if agentUserAuthenticationType is set to
none(1).
none(1) - no encryption used
des(2) - DES encryption usedrw Enumeration .1.3.6.1.4.1.4526.11.1.2.1.3.2.1.7 |
agentUserEncryptionPasswordSNMPv3 User Encryption Password
This object will return an empty string even if a password is
set. agentUserEncryptionType must be set to des(2) before this
object can be configured.
This object will return an empty string even if a password is set.rw DisplayString .1.3.6.1.4.1.4526.11.1.2.1.3.2.1.8 |
agentUserLockoutStatusDisplays whether the user account is locked due to excessive failed login attempts.ro Enumeration .1.3.6.1.4.1.4526.11.1.2.1.3.2.1.9 |
agentUserPasswordExpireTimeDate and time when the user's password expires (past or present). Only valid when
password aging is enabled.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.4526.11.1.2.1.3.2.1.10 |
agentSerialGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4526.11.1.2.1.5 |
agentSerialTimeoutagentSerialTimeout specifies the maximum connect time(in minutes)
without console activity. A value of 0 indicates that a console can
be connected indefinitely. The time range is 0 to 160.rw Integer32 .1.3.6.1.4.1.4526.11.1.2.1.5.1 |
agentSerialBaudrateagentSerialBaudrate specifies the current baud rate at which
the serial port will try to connect. The available values
are 1200, 2400, 4800, 9600, 19200, 38400,57600, and 115200 baud.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.1.5.2 |
agentSerialCharacterSizeagentSerialCharacterSize specifies the number of bits in
a character. The number of bits is always 8.ro Integer32 .1.3.6.1.4.1.4526.11.1.2.1.5.3 |
agentSerialHWFlowControlModeagentSerialHardwareFlowControl specifies whether hardware
flow-control is enabled or disabled. Hardware Flow Control is
always disabled.ro Enumeration .1.3.6.1.4.1.4526.11.1.2.1.5.4 |
agentSerialStopBitsagentSerialStopBits specifies the number of Stop bits per
character. The number of Stop bits is always 1.ro Integer32 .1.3.6.1.4.1.4526.11.1.2.1.5.5 |
agentSerialParityTypeagentSerialParityType specifies the Parity Method used on
the Serial Port. The Parity Method is always None.ro Enumeration .1.3.6.1.4.1.4526.11.1.2.1.5.6 |
agentPasswordManagementConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4526.11.1.2.1.6 |
agentPasswordManagementMinLengthMinimum length for user passwords
All new local user passwords must be at least this many characters in length.rw Integer32 .1.3.6.1.4.1.4526.11.1.2.1.6.1 |
agentPasswordManagementHistoryThe number of previous passwords to store for prevention of password reuse.
This ensures that each user does not reuse passwords often. A value of 0
indicates that no previous passwords will be stored.rw Integer32 .1.3.6.1.4.1.4526.11.1.2.1.6.2 |
agentPasswordManagementAgingThe maximum time that user passwords are valid, in days, from the time the
password is set. Once a password expires, the user will be required to enter
a new password following the first login after password expiration.
A value of 0 indicates that passwords never expire.rw Integer32 .1.3.6.1.4.1.4526.11.1.2.1.6.3 |
agentPasswordManagementLockAttemptsThe number of allowable failed local authentication attempts before the user's
account is locked. A value of 0 indicates that user accounts will never be locked.rw Integer32 .1.3.6.1.4.1.4526.11.1.2.1.6.4 |
agentLagConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4526.11.1.2.2 |
agentLagConfigCreateAgent LAG Create.
When this object is set with a non-empty string, a new LAG will be created
if possible with the entered string as its name.rw DisplayString .1.3.6.1.4.1.4526.11.1.2.2.1 |
agentLagSummaryConfigTableA summary table of the switch's LAG config entries SEQUENCE OF AgentLagSummaryConfigEntry .1.3.6.1.4.1.4526.11.1.2.2.2 |
agentLagSummaryConfigEntrySwitch's LAG config entry AgentLagSummaryConfigEntry .1.3.6.1.4.1.4526.11.1.2.2.2.1 |
agentLagSummaryLagIndexAgent LAG IfIndex.
This value corresponds with the LAG interface in the ifTable.ro Integer32 .1.3.6.1.4.1.4526.11.1.2.2.2.1.1 |
agentLagSummaryNameAgent LAG Name.
The associated name of the LAG used during creation.rw DisplayString .1.3.6.1.4.1.4526.11.1.2.2.2.1.2 |
agentLagSummaryFlushTimerAgent LAG FlushTimer.rwobsolete Integer32 .1.3.6.1.4.1.4526.11.1.2.2.2.1.3 |
agentLagSummaryLinkTrapAgent LAG LinkTrap.
Configures sending Link Up/Down traps when the LAG interface goes Up or Down.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.2.2.1.4 |
agentLagSummaryAdminModeAgent LAG AdminMode.
Administratively enables or disables this LAG interface.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.2.2.1.5 |
agentLagSummaryStpModeAgent LAG StpMode
If Dot1d is enabled, the valid values are:
dot1d(1), fast(2), and off(3)
If Dot1s is enabled, the valid values are:
off(3) and dot1s(4)rw Enumeration .1.3.6.1.4.1.4526.11.1.2.2.2.1.6 |
agentLagSummaryAddPortAgent LAG AddPort.
Set to a non 0 value to add a port to the LAG. Values correspond to
ifIndex values in the ifTable.
Note: agentPortType for the port to be added must be full duplex
and the same speed as previously added port(s), if any.rw Integer32 .1.3.6.1.4.1.4526.11.1.2.2.2.1.7 |
agentLagSummaryDeletePortAgent LAG DeletePort.
Set to a non 0 value to remove a port from the LAG. Values correspond to
ifIndex values in the ifTable.rw Integer32 .1.3.6.1.4.1.4526.11.1.2.2.2.1.8 |
agentLagSummaryStatusAgent LAG Status.
active(1) - This LAG is enabled.
destroy(6) - Set to this value to remove the LAG.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4526.11.1.2.2.2.1.9 |
agentLagSummaryTypeAgent LAG Type.
static(1) - This LAG is staticly maintained.
dynamic(2) - This LAG is dynamicly maintained.ro Enumeration .1.3.6.1.4.1.4526.11.1.2.2.2.1.10 |
agentLagSummaryStaticCapabilityAgent LAG Static Capability
enable(1) - Static capability is enabled for this LAG interface
disable(2) - Static capability is disabled for this LAG interfacerw Enumeration .1.3.6.1.4.1.4526.11.1.2.2.2.1.11 |
agentLagDetailedConfigTableA detailed table of the switch's LAG config entries SEQUENCE OF AgentLagDetailedConfigEntry .1.3.6.1.4.1.4526.11.1.2.2.3 |
agentLagDetailedConfigEntrySwitch's LAG config entry AgentLagDetailedConfigEntry .1.3.6.1.4.1.4526.11.1.2.2.3.1 |
agentLagDetailedLagIndexLAG indexro Integer32 .1.3.6.1.4.1.4526.11.1.2.2.3.1.1 |
agentLagDetailedIfIndexLAG port indexro Integer32 .1.3.6.1.4.1.4526.11.1.2.2.3.1.2 |
agentLagDetailedPortSpeedLAG port speed. See agentPortType for a description and list
of valid values.ro OBJECT IDENTIFIER .1.3.6.1.4.1.4526.11.1.2.2.3.1.3 |
agentLagDetailedPortStatusLAG port status.
active(1) - Actively participating in the LAG.
inactive(2) - Not participating in the LAG.ro Enumeration .1.3.6.1.4.1.4526.11.1.2.2.3.1.4 |
agentLagConfigStaticCapabilityAgent LAG Static Capability.
Configures whether Static LAGs are supported on this device.rwobsolete Enumeration .1.3.6.1.4.1.4526.11.1.2.2.4 |
agentNetworkConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4526.11.1.2.3 |
agentNetworkIPAddressThe switch's network ip addressrw IpAddress .1.3.6.1.4.1.4526.11.1.2.3.1 |
agentNetworkSubnetMaskThe switch's network subnet maskrw IpAddress .1.3.6.1.4.1.4526.11.1.2.3.2 |
agentNetworkDefaultGatewayThe switch's network default gatewayrw IpAddress .1.3.6.1.4.1.4526.11.1.2.3.3 |
agentNetworkBurnedInMacAddressThe switch's network Burned-In MAC addressro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.4526.11.1.2.3.4 |
agentNetworkLocalAdminMacAddressThe switch's network locally administered MAC addressrw PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.4526.11.1.2.3.5 |
agentNetworkMacAddressTypeThe switch's network Mac Address Typerw Enumeration .1.3.6.1.4.1.4526.11.1.2.3.6 |
agentNetworkConfigProtocolThe switch's network config protocolrw Enumeration .1.3.6.1.4.1.4526.11.1.2.3.7 |
agentNetworkWebModeThe switch's network config protocol on next bootuprwobsolete Enumeration .1.3.6.1.4.1.4526.11.1.2.3.8 |
agentNetworkJavaModeConfigures the use of the Java interface through the Web.rwobsolete Enumeration .1.3.6.1.4.1.4526.11.1.2.3.9 |
agentNetworkMgmtVlanThe VLAN ID through which the switch can be managed using the
agentNetworkIPAddressrw Integer32 .1.3.6.1.4.1.4526.11.1.2.3.10 |
agentNetworkIpv6AdminModeThe network port IPv6 administrative staterw Enumeration .1.3.6.1.4.1.4526.11.1.2.3.11 |
agentNetworkIpv6GatewayThe network port IPv6 Gateway Addressrw Ipv6AddressPrefix .1.3.6.1.4.1.4526.11.1.2.3.12 |
agentNetworkIpv6AddrTableThe list of IPv6 address prefixes
for the network port. SEQUENCE OF AgentNetworkIpv6AddrEntry .1.3.6.1.4.1.4526.11.1.2.3.13 |
agentNetworkIpv6AddrEntryAn interface entry containing objects of
a particular IPv6 address prefix AgentNetworkIpv6AddrEntry .1.3.6.1.4.1.4526.11.1.2.3.13.1 |
agentNetworkIpv6AddrPrefixThe service port IPv6 Address Prefix Ipv6AddressPrefix .1.3.6.1.4.1.4526.11.1.2.3.13.1.1 |
agentNetworkIpv6AddrPrefixLengthThe service port IPv6 Address Prefix Lengthrw INTEGER .1.3.6.1.4.1.4526.11.1.2.3.13.1.2 |
agentNetworkIpv6AddrEuiFlagThe service port IPv6 Eui Flagrw Enumeration .1.3.6.1.4.1.4526.11.1.2.3.13.1.3 |
agentNetworkIpv6AddrStatusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4526.11.1.2.3.13.1.4 |
agentServicePortConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4526.11.1.2.4 |
agentServicePortIPAddressThe switch's ServicePort ip addressrw IpAddress .1.3.6.1.4.1.4526.11.1.2.4.1 |
agentServicePortSubnetMaskThe switch's ServicePort subnet maskrw IpAddress .1.3.6.1.4.1.4526.11.1.2.4.2 |
agentServicePortDefaultGatewayThe switch's ServicePort default gatewayrw IpAddress .1.3.6.1.4.1.4526.11.1.2.4.3 |
agentServicePortBurnedInMacAddressThe switch's ServicePort Burned-In MAC addressro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.4526.11.1.2.4.4 |
agentServicePortConfigProtocolThe switch's ServicePort config protocolrw Enumeration .1.3.6.1.4.1.4526.11.1.2.4.5 |
agentServicePortIpv6AdminModeThe service port IPv6 administrative staterw Enumeration .1.3.6.1.4.1.4526.11.1.2.4.6 |
agentServicePortIpv6GatewayThe service port IPv6 Gateway Addressrw Ipv6AddressPrefix .1.3.6.1.4.1.4526.11.1.2.4.7 |
agentServicePortIpv6AddrTableThe list of IPv6 address prefixes for the
service port. SEQUENCE OF AgentServicePortIpv6AddrEntry .1.3.6.1.4.1.4526.11.1.2.4.8 |
agentServicePortIpv6AddrEntryAn interface entry containing objects of
a particular IPv6 address prefix AgentServicePortIpv6AddrEntry .1.3.6.1.4.1.4526.11.1.2.4.8.1 |
agentServicePortIpv6AddrPrefixThe service port IPv6 Address Prefix Ipv6AddressPrefix .1.3.6.1.4.1.4526.11.1.2.4.8.1.1 |
agentServicePortIpv6AddrPrefixLengthThe service port IPv6 Address Prefix Lengthrw INTEGER .1.3.6.1.4.1.4526.11.1.2.4.8.1.2 |
agentServicePortIpv6AddrEuiFlagThe service port IPv6 Eui Flagrw Enumeration .1.3.6.1.4.1.4526.11.1.2.4.8.1.3 |
agentServicePortIpv6AddrStatusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4526.11.1.2.4.8.1.4 |
agentSnmpConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4526.11.1.2.6 |
agentSnmpCommunityCreateCreates a new SNMP Community entry.
Defaults: IPAddress 0.0.0.0
IpMask 0.0.0.0
AccessMode read-only
Status configrw DisplayString .1.3.6.1.4.1.4526.11.1.2.6.1 |
agentSnmpCommunityConfigTableA table of the switch's SNMP Config entries SEQUENCE OF AgentSnmpCommunityConfigEntry .1.3.6.1.4.1.4526.11.1.2.6.2 |
agentSnmpCommunityConfigEntrySwitch's SNMP Config entry AgentSnmpCommunityConfigEntry .1.3.6.1.4.1.4526.11.1.2.6.2.1 |
agentSnmpCommunityIndexThe switch's Snmp Community Indexro Integer32 .1.3.6.1.4.1.4526.11.1.2.6.2.1.1 |
agentSnmpCommunityNameThe switch's Snmp Community Name
This name identifies each SNMP community;
the name can be up to 16 characters, and it is case-sensitive.
Community names in the SNMP community must be unique.
If you make multiple entries using the same community name,
the first entry is kept and processed and all duplicate entries are ignored.rw DisplayString .1.3.6.1.4.1.4526.11.1.2.6.2.1.2 |
agentSnmpCommunityIPAddressThe switch's Snmp Community IP Address
Client IP Address - This attribute is an IP address (or portion thereof)
from which this device will accept SNMP packets with the associated
community. The requesting entity's IP address is logical-ANDed with
the Client IP Mask and the result must match the Client IP Address.
Note: If the Client IP Mask is set
to 0.0.0.0, a Client IP Address of 0.0.0.0 matches all IP addresses.rw IpAddress .1.3.6.1.4.1.4526.11.1.2.6.2.1.3 |
agentSnmpCommunityIPMaskThe switch's Snmp Community IP Mask
Client IP Mask - This attribute is a mask to be logical-ANDed with the
requesting entity's IP address before comparison with the Client IP Address.
If the result matches with Client IP Address then the address is an
authenticated IP address. For example, if the Client IP Address
is 9.47.128.0 and the corresponding Client IP Mask is 255.255.255.0,
a range of incoming IP addresses would match, that is, the incoming IP
addresses could be a value in the following range: 9.47.128.0 to 9.47.128.255.
To have a specific IP address be the only authenticated IP address, set the
Client IP Address to the required IP address and set the Client IP Mask
to 255.255.255.255.rw IpAddress .1.3.6.1.4.1.4526.11.1.2.6.2.1.4 |
agentSnmpCommunityAccessModeThe switch's Snmp Community Access Mode
Access Mode - This value can be read-only or read/write.
A community with a read-only access allows for switch information to be
displayed. A community with a read/write access allows for configuration
changes to be made and for information to be displayed.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.6.2.1.5 |
agentSnmpCommunityStatusThe switch's Snmp Community Status.
active(1) - This community is active, allowing SNMP managers associated
with this community to manage the switch according to its
access right.
notInService(2) - This community is not active; no SNMP requests using this
community will be accepted. In this case the SNMP manager
associated with this community cannot manage the switch until
the Status is changed back to active(1).
config(3) - The community Status must be set to this value in order to
configure it. When creating a new community entry, initial
Status will be set to this value.
destroy(4) - Set to this value to remove the community from the agent.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.6.2.1.6 |
agentSnmpTrapReceiverCreateCreates a new trap receiver entry.
Defaults: IPAddress 0.0.0.0
status configrw DisplayString .1.3.6.1.4.1.4526.11.1.2.6.3 |
agentSnmpTrapReceiverConfigTableTrap messages are sent across a network to an SNMP Network Manager.
These messages alert the manager to events occurring within the switch
or on the network. Up to six simultaneous trap receivers are supported. SEQUENCE OF AgentSnmpTrapReceiverConfigEntry .1.3.6.1.4.1.4526.11.1.2.6.4 |
agentSnmpTrapReceiverConfigEntrySwitch's Snmp Trace Receiver Config entry AgentSnmpTrapReceiverConfigEntry .1.3.6.1.4.1.4526.11.1.2.6.4.1 |
agentSnmpTrapReceiverIndexThe switch's Snmp Trap Receiver Indexro Integer32 .1.3.6.1.4.1.4526.11.1.2.6.4.1.1 |
agentSnmpTrapReceiverCommunityNameThe switch's Snmp Trap Receiver Community Name.
This is the SNMP community name of the remote network manager;
the name can be up to 16 characters, and is case-sensitive.rw DisplayString .1.3.6.1.4.1.4526.11.1.2.6.4.1.2 |
agentSnmpTrapReceiverIPAddressIP Address - Each IP address parameter is four integer numbers.
The numbers range from 0 to 255.rw IpAddress .1.3.6.1.4.1.4526.11.1.2.6.4.1.3 |
agentSnmpTrapReceiverStatusThe switch's Snmp Trap Reciever Status.
active(1) - This trap receiver is active, allowing SNMP Traps to
be sent to this receiver.
notInService(2) - This trap reciever is not active; no SNMP Traps will
be sent to this reciever until it's set back to active(1).
config(3) - The trap reciever Status must be set to this value in order
to configure it. When creating a new trap receiver entry,
the Status will initially be set to this value.
Note: agentSnmpTrapReceiverIPAddress must be set to non-zero
before changing to active(1) or notInService(2).
destroy(4) - Set to this value to remove the trap receiver entry from
the agent.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.6.4.1.4 |
agentSnmpTrapReceiverVersionThe version of trap sent to this Reciever.
snmpv1(1) - This will send a SNMPv1 trap.
snmpv2c(2) - This will send a SNMPv2c trap.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.6.4.1.5 |
agentSnmpTrapReceiverIpv6AddressIPv6 Address for SNMP receiver.rw Ipv6AddressPrefix .1.3.6.1.4.1.4526.11.1.2.6.4.1.6 |
agentSnmpTrapFlagsConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4526.11.1.2.6.5 |
agentSnmpAuthenticationTrapFlagAuthentication Flag - Enable/Disable authentication Flag.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.6.5.1 |
agentSnmpLinkUpDownTrapFlagLink Up/Down Flag - Enable/Disable Link Up/Link Down traps for the
entire switch. When set to Enable, the Link Up/Down traps will be
sent only if the Link Trap flag setting associated with the port
(Port Configuration Menu) is set to Enable.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.6.5.2 |
agentSnmpMultipleUsersTrapFlagMultiple Users Flag - Enable/Disable Multiple User traps. When the value
is set to Enable, a Multiple User Trap is sent whenever someone logs in
to the terminal interface (EIA 232 or Telnet) and there is already an
existing terminal interface session.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.6.5.3 |
agentSnmpSpanningTreeTrapFlagSpanning Tree Flag - This flag enables the sending of new root traps and
topology change notification traps.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.6.5.4 |
agentSnmpBroadcastStormTrapFlagBroadcast Storm Flag - This flag enables or disables the broadcast
storm trap. You must also enable Broadcast Storm Recovery Mode
(see the Switch Configuration Menu). When this
value is set to Enable and Broadcast Storm Recovery mode is set to Enable,
the Broadcast Storm Start/End traps are sent when the switch enters and
leaves Broadcast Storm Recovery.rwobsolete Enumeration .1.3.6.1.4.1.4526.11.1.2.6.5.5 |
agentSpanningTreeConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4526.11.1.2.7 |
agentSpanningTreeModeThe switch's Spanning Tree Switch Statusrw Enumeration .1.3.6.1.4.1.4526.11.1.2.7.1 |
agentSwitchConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4526.11.1.2.8 |
agentSwitchAddressAgingTimeoutTableThe switch's address aging timeout table SEQUENCE OF AgentSwitchAddressAgingTimeoutEntry .1.3.6.1.4.1.4526.11.1.2.8.4 |
agentSwitchAddressAgingTimeoutEntryAging information about a specific Filtering Database. AgentSwitchAddressAgingTimeoutEntry .1.3.6.1.4.1.4526.11.1.2.8.4.1 |
agentSwitchAddressAgingTimeoutThe FDB entry's address aging timeout (in seconds)rw Integer32 .1.3.6.1.4.1.4526.11.1.2.8.4.1.1 |
agentSwitchStaticMacFilteringTableThe switch's static Mac filtering table SEQUENCE OF AgentSwitchStaticMacFilteringEntry .1.3.6.1.4.1.4526.11.1.2.8.5 |
agentSwitchStaticMacFilteringEntryPer-port ingress/egress filter configuration based on VLAN Id and MAC address. AgentSwitchStaticMacFilteringEntry .1.3.6.1.4.1.4526.11.1.2.8.5.1 |
agentSwitchStaticMacFilteringVlanIdThe Static MAC Filter Vlan Idro Integer32 .1.3.6.1.4.1.4526.11.1.2.8.5.1.1 |
agentSwitchStaticMacFilteringAddressThe Static MAC Filter MAC addressro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.4526.11.1.2.8.5.1.2 |
agentSwitchStaticMacFilteringSourcePortMaskThe Static MAC Filter source port mask.
When setting this value, the system will ignore configuration for ports not
between the first and last valid ports. Configuration of any port numbers
between this range that are not valid ports return a failure message, but will
still apply configuration for valid ports.
To obtain port numbers from interface numbers, use the objects
agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable
table.rw AgentPortMask .1.3.6.1.4.1.4526.11.1.2.8.5.1.3 |
agentSwitchStaticMacFilteringDestPortMaskThe Static MAC Filter destination port mask.
When setting this value, the system will ignore configuration for ports not
between the first and last valid ports. Configuration of any port numbers
between this range that are not valid ports return a failure message, but will
still apply configuration for valid ports.
To obtain port numbers from interface numbers, use the objects
agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable
table.
Configuring destination port mask for a unicast MAC filter is not supported on some platforms.rw AgentPortMask .1.3.6.1.4.1.4526.11.1.2.8.5.1.4 |
agentSwitchStaticMacFilteringStatusThe Static MAC Filter status.
Supported values:
active(1) - valid entry
createAndGo(4) - used to create a new entry
destroy(6) - removes the entryrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4526.11.1.2.8.5.1.5 |
agentSwitchSnoopingGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4526.11.1.2.8.6 |
agentSwitchSnoopingCfgTableA table of the IGMP/MLD Snooping Global configuration entries. SEQUENCE OF AgentSwitchSnoopingCfgEntry .1.3.6.1.4.1.4526.11.1.2.8.6.1 |
agentSwitchSnoopingCfgEntryRepresents entry for Snooping switch Configuration. AgentSwitchSnoopingCfgEntry .1.3.6.1.4.1.4526.11.1.2.8.6.1.1 |
agentSwitchSnoopingProtocolThe protocol type of network protocol in use.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.4526.11.1.2.8.6.1.1.1 |
agentSwitchSnoopingAdminModeThis enables or disables Snooping on the system.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.8.6.1.1.2 |
agentSwitchSnoopingPortMaskIGMP/MLD Snooping Port Mask.
This allows configuration of IGMP/MLD Snooping on selected ports.
IGMP Snooping cannot be enabled on an interface that has routing
enabled, or is a member of a LAG. If a port which has IGMP Snooping
enabled becomes enabled for routing, or is enlisted as a member of a
LAG, IGMP Snooping functionality will be disabled on that port. IGMP
Snooping functionality will be subsequently be reenabled if routing is
disabled or LAG membership is removed from an interface that had previously
had IGMP Snooping enabled.
To obtain port numbers from interface numbers, use the objects
agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable
table.rw AgentPortMask .1.3.6.1.4.1.4526.11.1.2.8.6.1.1.3 |
agentSwitchSnoopingMulticastControlFramesProcessedMulticast Control Frames Processed by CPU.
The number of multicast control frames that have been processed by the CPU.ro Counter32 .1.3.6.1.4.1.4526.11.1.2.8.6.1.1.4 |
agentSwitchSnoopingIntfGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4526.11.1.2.8.7 |
agentSwitchSnoopingIntfTableA table of the IGMP Snooping Interface configuration entries. SEQUENCE OF AgentSwitchSnoopingIntfEntry .1.3.6.1.4.1.4526.11.1.2.8.7.1 |
agentSwitchSnoopingIntfEntryRepresents entry for a IGMP Snooping Interface. AgentSwitchSnoopingIntfEntry .1.3.6.1.4.1.4526.11.1.2.8.7.1.1 |
agentSwitchSnoopingIntfIndexThe port number to be selected. Each port maps to an interface.ro Unsigned32 .1.3.6.1.4.1.4526.11.1.2.8.7.1.1.1 |
agentSwitchSnoopingIntfAdminModeThis enables or disables IGMP Snooping on a selected interface.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.8.7.1.1.2 |
agentSwitchSnoopingIntfGroupMembershipIntervalThe amount of time in seconds that a switch will wait for a report
from a particular group on the selected interface before deleting the
interface from the entry. This value must be greater than
agentSwitchIGMPSnoopingIntfMaxResponseTime.rw Integer32 .1.3.6.1.4.1.4526.11.1.2.8.7.1.1.3 |
agentSwitchSnoopingIntfMaxResponseTimeThe amount of time in seconds a switch will wait after sending
a query on the selected interface because it did not receive a report for
a particular group in that interface. This value must be less
than agentSwitchIGMPSnoopingIntfGroupMembershipInterval.rw Integer32 .1.3.6.1.4.1.4526.11.1.2.8.7.1.1.4 |
agentSwitchSnoopingIntfMRPExpirationTimeThe amount of time in seconds that a switch will wait for a query to be
received on the selected interface before the interface is removed from
the list of interfaces with multicast routers attached.rw Integer32 .1.3.6.1.4.1.4526.11.1.2.8.7.1.1.5 |
agentSwitchSnoopingIntfFastLeaveAdminModeThis enables or disables IGMP Snooping on the selected interface.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.8.7.1.1.6 |
agentSwitchSnoopingIntfMulticastRouterModeThis enables or disables Multicast Routing on the selected interface.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.8.7.1.1.7 |
agentSwitchSnoopingIntfVlanIDsThis field lists all the VlanIDs which include the selected interface.ro VlanList .1.3.6.1.4.1.4526.11.1.2.8.7.1.1.8 |
agentSwitchSnoopingVlanGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4526.11.1.2.8.8 |
agentSwitchSnoopingVlanTableA table of the IGMP Snooping Vlan configuration entries. SEQUENCE OF AgentSwitchSnoopingVlanEntry .1.3.6.1.4.1.4526.11.1.2.8.8.1 |
agentSwitchSnoopingVlanEntryRepresents entry for a IGMP Snooping Vlan. AgentSwitchSnoopingVlanEntry .1.3.6.1.4.1.4526.11.1.2.8.8.1.1 |
agentSwitchSnoopingVlanAdminModeThis enables or disables IGMP Snooping on a selected Vlan interface.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.8.8.1.1.1 |
agentSwitchSnoopingVlanGroupMembershipIntervalThe amount of time in seconds that a switch will wait for a report
from a particular group on the selected vlan before deleting the
interface participating in the vlan from the entry. This value must
be greater than agentSwitchIGMPSnoopingIntfMaxResponseTime.rw Integer32 .1.3.6.1.4.1.4526.11.1.2.8.8.1.1.2 |
agentSwitchSnoopingVlanMaxResponseTimeThe amount of time in seconds a switch will wait after sending
a query on the selected vlan because it did not receive a report for
a particular group in the interface participating in the vlan.
This value must be less than
agentSwitchIGMPSnoopingIntfGroupMembershipInterval.rw Integer32 .1.3.6.1.4.1.4526.11.1.2.8.8.1.1.3 |
agentSwitchSnoopingVlanFastLeaveAdminModeThis enables or disables IGMP Snooping on the selected vlan.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.8.8.1.1.4 |
agentSwitchSnoopingVlanMRPExpirationTimeThe amount of time in seconds that a switch will wait for a query to be
received on the selected interface participating in the vlan before the
interface is removed from the list of interfaces with multicast routers
attached. This parameter is configurable only for exisiting Vlans.rw Integer32 .1.3.6.1.4.1.4526.11.1.2.8.8.1.1.5 |
agentSwitchVlanStaticMrouterGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4526.11.1.2.8.9 |
agentSwitchVlanStaticMrouterTableA table of the IGMP Static Mrouter Configuration parameters. SEQUENCE OF AgentSwitchVlanStaticMrouterEntry .1.3.6.1.4.1.4526.11.1.2.8.9.1 |
agentSwitchVlanStaticMrouterEntryRepresents entry for a IGMP Static Mrouter. AgentSwitchVlanStaticMrouterEntry .1.3.6.1.4.1.4526.11.1.2.8.9.1.1 |
agentSwitchVlanStaticMrouterAdminModeThis enables or disables IGMP Mrouter on a per-interface per-vlan basis.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.8.9.1.1.1 |
agentSwitchMFDBGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4526.11.1.2.8.10 |
agentSwitchMFDBTableThe Multicast Forwarding Database table SEQUENCE OF AgentSwitchMFDBEntry .1.3.6.1.4.1.4526.11.1.2.8.10.1 |
agentSwitchMFDBEntryContains Forwarding and Filtering information per Vlan Index, MAC Address, and
Component User. AgentSwitchMFDBEntry .1.3.6.1.4.1.4526.11.1.2.8.10.1.1 |
agentSwitchMFDBVlanIdVlan Index for which this entry is associated with.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.4526.11.1.2.8.10.1.1.1 |
agentSwitchMFDBMacAddressA multicast MAC address for which the switch has forwarding and or
filtering information.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.4526.11.1.2.8.10.1.1.2 |
agentSwitchMFDBProtocolTypeThe component that is responsible for this entry in the Multicast
Forwarding Database.ro Enumeration .1.3.6.1.4.1.4526.11.1.2.8.10.1.1.3 |
agentSwitchMFDBTypeThis displays the type of the entry.
static(1) - Entries configured by the end user
dynamic(2) - Entries added as a result of a learning process or protocolro Enumeration .1.3.6.1.4.1.4526.11.1.2.8.10.1.1.4 |
agentSwitchMFDBDescriptionText description of this multicast table entry.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4526.11.1.2.8.10.1.1.5 |
agentSwitchMFDBForwardingPortMaskBitMask indicating which ports this entry indicates should be forwarded.
To obtain port numbers from interface numbers, use the objects
agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable
table.ro AgentPortMask .1.3.6.1.4.1.4526.11.1.2.8.10.1.1.6 |
agentSwitchMFDBFilteringPortMaskBitMask indicating which ports this entry indicates should be filtered.
To obtain port numbers from interface numbers, use the objects
agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable
table.ro AgentPortMask .1.3.6.1.4.1.4526.11.1.2.8.10.1.1.7 |
agentSwitchMFDBSummaryTableThe Multicast Forwarding Database Summary table SEQUENCE OF AgentSwitchMFDBSummaryEntry .1.3.6.1.4.1.4526.11.1.2.8.10.2 |
agentSwitchMFDBSummaryEntrySummarizes the forwarding ports for all components registered for all
MFDB table entries with the same Vlan Index and MAC Address. AgentSwitchMFDBSummaryEntry .1.3.6.1.4.1.4526.11.1.2.8.10.2.1 |
agentSwitchMFDBSummaryVlanIdVlan Index for which this entry is associated with.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.4526.11.1.2.8.10.2.1.1 |
agentSwitchMFDBSummaryMacAddressA multicast MAC address for which the switch has forwarding and or
filtering information.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.4526.11.1.2.8.10.2.1.2 |
agentSwitchMFDBSummaryForwardingPortMaskPort Mask indicating which ports this entry indicates should be forwarded.
To obtain port numbers from interface numbers, use the objects
agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable
table.ro AgentPortMask .1.3.6.1.4.1.4526.11.1.2.8.10.2.1.3 |
agentSwitchMFDBMaxTableEntriesThis displays the maximum number of entries that can possibly be in
the Multicast Forwarding Database table.ro Gauge32 .1.3.6.1.4.1.4526.11.1.2.8.10.3 |
agentSwitchMFDBMostEntriesUsedThis displays the largest number of entries that have been present
in the Multicast Forwarding Database table. This value is also known
as the MFDB high-water mark.ro Gauge32 .1.3.6.1.4.1.4526.11.1.2.8.10.4 |
agentSwitchMFDBCurrentEntriesThis displays the current number of entries in the Multicast
Forwarding Database table.ro Gauge32 .1.3.6.1.4.1.4526.11.1.2.8.10.5 |
agentSwitchStormControlGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4526.11.1.2.8.12 |
agentSwitchDot3FlowControlModeConfig switchconfig flowcontrol allows you to enable or disable
802.3x flow control for the switch. This value
applies to only full-duplex mode ports.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.8.12.1 |
agentSwitchBroadcastControlModeThe switch config broadcast allows you to enable or disable
broadcast storm recovery mode. When you specify Enable for Broadcast
Storm Recovery and the broadcast traffic on any Ethernet port exceeds
the configured threshold, the switch blocks (discards) the broadcast
traffic.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.8.12.4 |
agentSwitchBroadcastControlThresholdConfigures the broadcast storm recovery threshold for this port
as a percentage of port speed.rw Unsigned32 .1.3.6.1.4.1.4526.11.1.2.8.12.5 |
agentSwitchMulticastControlModeThe switch config multicast allows you to enable or disable
multicast storm recovery mode. When you specify Enable for multicast
Storm Recovery and the multicast traffic on any Ethernet port exceeds
the configured threshold, the switch blocks (discards) the multicast
traffic.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.8.12.6 |
agentSwitchMulticastControlThresholdConfigures the multicast storm recovery threshold for this port
as a percentage of port speed.rw Unsigned32 .1.3.6.1.4.1.4526.11.1.2.8.12.7 |
agentSwitchUnicastControlModeThe switch config unicast allows you to enable or disable
unicast storm recovery mode. When you specify Enable for unicast
Storm Recovery and the unknown unicast traffic on any Ethernet port exceeds
the configured threshold, the switch blocks (discards) the unknown unicast
traffic.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.8.12.8 |
agentSwitchUnicastControlThresholdConfigures the unicast storm recovery threshold for this port
as a percentage of port speed.rw Unsigned32 .1.3.6.1.4.1.4526.11.1.2.8.12.9 |
agentDhcpFilteringGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4526.11.1.2.8.15 |
agentDhcpFilteringAdminModeDhcp Filtering mode:
enable - enable dhcp filtering mode
disable - disable dhcp filtering mode.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.8.15.1 |
agentDhcpFilteringPortConfigTableA table that contains the configuration objects for the
with each port. SEQUENCE OF AgentDhcpFilteringPortConfigEntry .1.3.6.1.4.1.4526.11.1.2.8.15.2 |
agentDhcpFilteringPortConfigEntryThe configuration information for Dhcp Filtering. AgentDhcpFilteringPortConfigEntry .1.3.6.1.4.1.4526.11.1.2.8.15.2.1 |
agentDhcpFilteringPortTrustedModePort's DHCP mode. It can be either trusted or untrusted
default will be untrusted.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.8.15.2.1.1 |
agentSwitchProtectedPortConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4526.11.1.2.8.18 |
agentSwitchProtectedPortTableThe switch's protected port mapping table SEQUENCE OF AgentSwitchProtectedPortEntry .1.3.6.1.4.1.4526.11.1.2.8.18.1 |
agentSwitchProtectedPortEntryProtected ports assigned to groups. AgentSwitchProtectedPortEntry .1.3.6.1.4.1.4526.11.1.2.8.18.1.1 |
agentSwitchProtectedPortGroupIdThe group that this port belongs to Integer32 .1.3.6.1.4.1.4526.11.1.2.8.18.1.1.1 |
agentSwitchProtectedPortGroupNameThe name of the grouprw DisplayString .1.3.6.1.4.1.4526.11.1.2.8.18.1.1.2 |
agentSwitchProtectedPortPortListThe set of ports that are protected in this grouprw PortList .1.3.6.1.4.1.4526.11.1.2.8.18.1.1.3 |
agentSwitchSnoopingQuerierGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4526.11.1.2.8.20 |
agentSwitchSnoopingQuerierCfgTableA table of the IGMP/MLD Snooping Querier Global configuration entries. SEQUENCE OF AgentSwitchSnoopingQuerierCfgEntry .1.3.6.1.4.1.4526.11.1.2.8.20.1 |
agentSwitchSnoopingQuerierCfgEntryRepresents entry for Snooping Querier Configuration. AgentSwitchSnoopingQuerierCfgEntry .1.3.6.1.4.1.4526.11.1.2.8.20.1.1 |
agentSwitchSnoopingQuerierAdminModeThis enables or disables Snooping Querier on the system.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.8.20.1.1.1 |
agentSwitchSnoopingQuerierVersionThis specifies the multicast protocol versions that are
supported by the system.rw Integer32 .1.3.6.1.4.1.4526.11.1.2.8.20.1.1.2 |
agentSwitchSnoopingQuerierAddressThis specifies the default source ip address to be used
while generating general queries.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.4526.11.1.2.8.20.1.1.3 |
agentSwitchSnoopingQuerierQueryIntervalThis specified the timer interval after which the system
generates general queries.rw Integer32 .1.3.6.1.4.1.4526.11.1.2.8.20.1.1.4 |
agentSwitchSnoopingQuerierExpiryIntervalThis specified the timer interval after which the detected
other querier information is no longer valid.rw Integer32 .1.3.6.1.4.1.4526.11.1.2.8.20.1.1.5 |
agentSwitchSnoopingQuerierVlanTableA table of the Snooping Querier Vlan configuration entries. SEQUENCE OF AgentSwitchSnoopingQuerierVlanEntry .1.3.6.1.4.1.4526.11.1.2.8.20.2 |
agentSwitchSnoopingQuerierVlanEntryRepresents entry for a Snooping Querier configurable Vlan. AgentSwitchSnoopingQuerierVlanEntry .1.3.6.1.4.1.4526.11.1.2.8.20.2.1 |
agentSwitchSnoopingQuerierVlanAdminModeThis enables or disables Snooping Querier on a selected Vlan interface.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.8.20.2.1.1 |
agentSwitchSnoopingQuerierVlanOperModeThis specifies the current state of the Snooping Querier on a selected vlan interfacero Enumeration .1.3.6.1.4.1.4526.11.1.2.8.20.2.1.2 |
agentSwitchSnoopingQuerierElectionParticipateModeThis enables or disables the Snooping Querier Election Participation mode. When enabled
snooping querier switch will participate in querier election up on discovering another
querier in the specified vlan. When disabled, up on discovering another querier, snooping
querier moves to non-querier state.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.8.20.2.1.3 |
agentSwitchSnoopingQuerierVlanAddressThis specifies the default source ip address to be used while generating general queries on
the specified vlan.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.4526.11.1.2.8.20.2.1.4 |
agentSwitchSnoopingQuerierOperVersionThis specifies the multicast protocol version that is currently being used by the snooping
switch for the specified vlan while generating query messages.ro Integer32 .1.3.6.1.4.1.4526.11.1.2.8.20.2.1.5 |
agentSwitchSnoopingQuerierOperMaxResponseTimeThe amount of time in seconds a switch will wait after sending
a query on the selected vlan because it did not receive a report for
a particular group in the interface participating in the vlan. This
object is valid only when agentSwitchSnoopingQuerierOperVersion object
is valid.ro Integer32 .1.3.6.1.4.1.4526.11.1.2.8.20.2.1.6 |
agentSwitchSnoopingQuerierLastQuerierAddressThis specifies the last querier's ip address for the specified vlan.
It represents the detected other multicast querier in the vlan.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.4526.11.1.2.8.20.2.1.7 |
agentSwitchSnoopingQuerierLastQuerierVersionThis specifies the multicast protocol version that is currently being used
by the detected other multicast querier for the specified vlan.ro Integer32 .1.3.6.1.4.1.4526.11.1.2.8.20.2.1.8 |
agentTransferConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4526.11.1.2.9 |
agentTransferUploadGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4526.11.1.2.9.1 |
agentTransferUploadModeTransfer upload mode configures the mode to use when uploading from the
switch. The mode is either X/Y/ZMODEM, TFTP, SFTP or SCP. X/Y/ZMODEM is
valid only when the file transfer is initiated by the serial EIA 232 port.
SFTP and SCP are only allowed if the SSH feature is present.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.9.1.1 |
agentTransferUploadServerIPTransfer upload server IP configures the IP address of the server
where the file is located. It is valid only when the Transfer Mode is
TFTP, SFTP, or SCP. The address is 4 integer bytes ranging from 0 to 255.
This object is deprecated in favour of agentTransferUploadServerAddress
and agentTransferUploadServerAddressType.rwdeprecated IpAddress .1.3.6.1.4.1.4526.11.1.2.9.1.2 |
agentTransferUploadPathTransfer upload path configures the directory path where the file
is to be uploaded to. The switch remembers the last file path used.rw DisplayString .1.3.6.1.4.1.4526.11.1.2.9.1.3 |
agentTransferUploadFilenameTransfer upload filename configures the file name for the file being
uploaded from the switch. It can be up to 32 alphanumeric characters.
The switch remembers the last file name used.
File path can be appended to the file name if the string is less than 17
characters. Otherwise, the File Path field will need to be used and the
File Name will be appended to the File Path as is. An example would be
File Path set to c:\tftp\code\ and File Name set to e1r1v1.opr.
Note: File Name, File Path, and Server IP Address are applicable
only if the Transfer Mode is TFTP, SFTP or SCP.rw DisplayString .1.3.6.1.4.1.4526.11.1.2.9.1.4 |
agentTransferUploadDataTypeTransfer upload datatype configures the type of file to upload from the
switch.
The types for upload are:
- Configuration File
- Error log
- Message log
- Trap log
- Banner Filerw Enumeration .1.3.6.1.4.1.4526.11.1.2.9.1.5 |
agentTransferUploadStartTransfer upload start will start an upload transfer.
The agentTransferUploadMode object must not be set to xmodem(2),
ymodem(3), or zmodem(4) to initiate a transfer via SNMP.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.9.1.6 |
agentTransferUploadStatusIndicates the current status of an upload transfer.ro Enumeration .1.3.6.1.4.1.4526.11.1.2.9.1.7 |
agentTransferUploadServerAddressTypeThe type of the serverip address, as defined in the InetAddress MIB.
The agentTransferUploadServerAddress object is intepreted within the
context of agentTransferUploadServerAddressTyperw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.4526.11.1.2.9.1.8 |
agentTransferUploadServerAddressTransfer upload serverip configures the IP address of the server
where the file is to be uploaded to.It is valid only when the
Transfer Mode is TFTP, SFTP or SCP.
The type of this address is determined by the value of the
agentTransferUploadServerAddressType object.
The values for agentTransferUploadServerAddressType and
agentTransferUploadServerAddress must be consistent.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.4526.11.1.2.9.1.9 |
agentTransferUploadImagenameTransfer upload image name. Sets the image to be uploaded as the specified
name
Note: Imagename, File Name, File Path, and Server IP Address are applicable
only if the Transfer Mode is TFTP, SFTP or SCP.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.9.1.10 |
agentTransferUploadUsernameUsername applicable only to secure upload types, i.e., SFTP or SCP.rw DisplayString .1.3.6.1.4.1.4526.11.1.2.9.1.11 |
agentTransferUploadPasswordPassword applicable only to secure upload types, i.e. SFTP or SCP.rw DisplayString .1.3.6.1.4.1.4526.11.1.2.9.1.12 |
agentTransferDownloadGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4526.11.1.2.9.2 |
agentTransferDownloadModeTransfer download mode configures the mode to use when downloading
to the switch. The mode is either X/Y/ZMODEM, TFTP, SFTP or SCP. X/Y/ZMODEM is valid only
when the file transfer is initiated by the serial EIA 232 port. SFTP and SCP
are only allowed if the SSH feature is present.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.9.2.1 |
agentTransferDownloadServerIPTransfer download serverip configures the IP address of the server
where the file is located. It is valid only when the Transfer Mode is TFTP, SFTP or
SCP.
The address is 4 integer bytes ranging from 0 to 255.
This object is deprecated in favour of agentTransferDownloadServerAddress
and agentTransferDownloadServerAddressType.rwdeprecated IpAddress .1.3.6.1.4.1.4526.11.1.2.9.2.2 |
agentTransferDownloadPathTransfer download path configures the directory path where the
file is located. The switch remembers the last file path used.rw DisplayString .1.3.6.1.4.1.4526.11.1.2.9.2.3 |
agentTransferDownloadFilenameTransfer download filename configures the file name for the file
being downloaded to the switch. It can be up to 32 alphanumeric characters.
The switch remembers the last file name used.
File path can be appended to the file name if the string is less than 33
characters. Otherwise, the File Path field will need to be used and the
File Name will be appended to the File Path as is. An example would be
File Path set to c:\tftp\code\ and File Name set to e1r1v1.opr.
Note: Imagename, File Name, File Path, and Server IP Address are applicable
only if the Transfer Mode is TFTP, SFTP or SCP.rw DisplayString .1.3.6.1.4.1.4526.11.1.2.9.2.4 |
agentTransferDownloadDataTypeTransfer download datatype configures the type of file to download to
the switch.
The types for download are:
code - Code File
config - Configuration File
sshkey-rsa1 - SSH-1 RSA Key File
sshkey-rsa2 - SSH-2 RSA Key PEM File
sshkey-dsa - SSH-2 DSA Key PEM File
sslpem-root - SSL Trusted Root Certificate PEM File
sslpem-server - SSL Server Certificate PEM File
sslpem-dhweak - SSL DH Weak Encryption Parameter PEM File
sslpem-dhstrong - SSL DH Strong Encryption Parameter PEM File
cli-banner - CLI Banner File
kernel - Kernel File
Note: SSH Key files can only be downloaded if SSH Server is administratively
disabled, and there are no active SSH sessions.
Kernel file can be downloaded only on raptor platform and linux operating system.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.9.2.5 |
agentTransferDownloadStartTransfer download start will start an download transfer.
The agentTransferDownloadMode object must not be set to xmodem(2),
ymodem(3), or zmodem(4) to initiate a transfer via SNMP.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.9.2.6 |
agentTransferDownloadStatusIndicates the current status of an download transfer.ro Enumeration .1.3.6.1.4.1.4526.11.1.2.9.2.7 |
agentTransferDownloadServerAddressTypeThe type of the serverip address, as defined in the InetAddress MIB.
The agentTransferDownloadServerAddress object is intepreted within the
context of agentTransferDownloadServerAddressTyperw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.4526.11.1.2.9.2.8 |
agentTransferDownloadServerAddressTransfer download serverip configures the IP address of the server
where the file is to be downloaded from.It is valid only when the
Transfer Mode is TFTP, SFTP, or SCP.
The type of this address is determined by the value of the
agentTransferDownloadServerAddressType object.
The values for agentTransferDownloadServerAddressType and
agentTransferDownloadServerAddress must be consistent.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.4526.11.1.2.9.2.9 |
agentTransferDownloadImagenameTransfer download image name. Sets the downloaded image as the specified
name
Note: Imagename, File Name, File Path, and Server IP Address are applicable
only if the Transfer Mode is TFTP, SFTP or SCP.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.9.2.10 |
agentTransferDownloadUsernameUsername applicable only to secure download types, i.e., SFTP or SCP.rw DisplayString .1.3.6.1.4.1.4526.11.1.2.9.2.11 |
agentTransferDownloadPasswordPassword applicable only to secure download types, i.e. SFTP or SCP.rw DisplayString .1.3.6.1.4.1.4526.11.1.2.9.2.12 |
agentImageConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4526.11.1.2.9.3 |
agentImage1The image1 softwate version .ro DisplayString .1.3.6.1.4.1.4526.11.1.2.9.3.1 |
agentImage2The image2 software version.ro DisplayString .1.3.6.1.4.1.4526.11.1.2.9.3.2 |
agentActiveImageThe active image name. image1 or image2.ro DisplayString .1.3.6.1.4.1.4526.11.1.2.9.3.3 |
agentNextActiveImageThe next active image name.
user assigns either image1 or image2.rw DisplayString .1.3.6.1.4.1.4526.11.1.2.9.3.4 |
agentPortMirroringGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4526.11.1.2.10 |
agentMirroredPortIfIndexIfIndex of the mirrored portrwobsolete Integer32 .1.3.6.1.4.1.4526.11.1.2.10.1 |
agentProbePortIfIndexIfIndex of the probe portrwobsolete Integer32 .1.3.6.1.4.1.4526.11.1.2.10.2 |
agentPortMirroringModePort mirroring mode:
enable - enable mirroring mode
disable - disable mirroring mode
delete - clear MirroredPort and Probe Port configurationrwobsolete Enumeration .1.3.6.1.4.1.4526.11.1.2.10.3 |
agentPortMirrorTableThis table includes entries for each Port Mirroring session. SEQUENCE OF AgentPortMirrorEntry .1.3.6.1.4.1.4526.11.1.2.10.4 |
agentPortMirrorEntryProvides configuration of a Port Mirroring session specifying the
destination port, and the source Port Mask, providing a many-to-one
mapping. AgentPortMirrorEntry .1.3.6.1.4.1.4526.11.1.2.10.4.1 |
agentPortMirrorSessionNumThe Session number of this mirroring entry. The number of sessions is
fixed, and is platform dependant. Unsigned32 .1.3.6.1.4.1.4526.11.1.2.10.4.1.1 |
agentPortMirrorDestinationPortThe port which traffic from the mirrored ports will be sent to.rw Unsigned32 .1.3.6.1.4.1.4526.11.1.2.10.4.1.2 |
agentPortMirrorSourcePortMaskThe ports from which traffic will be sent to the destination port.
The destination port can not be included in this list of ports.rw AgentPortMask .1.3.6.1.4.1.4526.11.1.2.10.4.1.3 |
agentPortMirrorAdminModeThe status of this port mirroring session.
enable(1) - This session is active and all traffic from the source ports
will be mirrored to the destination port.
disable(2) - This session is not active.
delete(3) - Remove the configuration for this Sessionrw Enumeration .1.3.6.1.4.1.4526.11.1.2.10.4.1.4 |
agentPortMirrorTypeTableThis table includes entries for each source port's direction of port mirroring. SEQUENCE OF AgentPortMirrorTypeEntry .1.3.6.1.4.1.4526.11.1.2.10.5 |
agentPortMirrorTypeEntryProvides configuration of a Port Mirroring direction specifying the
session of the port mirroring and source port AgentPortMirrorTypeEntry .1.3.6.1.4.1.4526.11.1.2.10.5.1 |
agentPortMirrorTypeSourcePortThe port from which traffic will be sent to the destination port.
This port should be a source port in the corresponding session Unsigned32 .1.3.6.1.4.1.4526.11.1.2.10.5.1.1 |
agentPortMirrorTypeTypeThe direction of the data to be mirrored on this source port.
tx(1) - The data that is transmitted from the source port.
rx(2) - The data that is received on the source port.
txrx(3) - The data that is transmitted/received from/on the source portrw Enumeration .1.3.6.1.4.1.4526.11.1.2.10.5.1.2 |
agentDot3adAggPortTableThis table provides 802.3ad link aggregation information for each
physical port that is not available through the standard MIB. SEQUENCE OF AgentDot3adAggPortEntry .1.3.6.1.4.1.4526.11.1.2.12 |
agentDot3adAggPortEntryInformation about a table entry. The agentDot3adAggPort identifies
the external interface number of the port. AgentDot3adAggPortEntry .1.3.6.1.4.1.4526.11.1.2.12.1 |
agentDot3adAggPortifIndex of this physical portro Integer32 .1.3.6.1.4.1.4526.11.1.2.12.1.1 |
agentDot3adAggPortLACPModeEnable/disable 802.3ad LACP on this portrw Enumeration .1.3.6.1.4.1.4526.11.1.2.12.1.2 |
agentPortConfigTableA table of the switch's physical port config entries SEQUENCE OF AgentPortConfigEntry .1.3.6.1.4.1.4526.11.1.2.13 |
agentPortConfigEntrySwitch's physical port config entry AgentPortConfigEntry .1.3.6.1.4.1.4526.11.1.2.13.1 |
agentPortDot1dBasePortThe port number of this port.ro Integer32 .1.3.6.1.4.1.4526.11.1.2.13.1.1 |
agentPortIfIndexThe switch's Port IfIndexro Integer32 .1.3.6.1.4.1.4526.11.1.2.13.1.2 |
agentPortIanaTypeThe switch's Port Typero IANAifType (IANAifType-MIB) .1.3.6.1.4.1.4526.11.1.2.13.1.3 |
agentPortSTPModeThe switch's Port Spanning Tree Protocol Mode
STP mode values are:
dot1d (the default)
fast, indicates you want to use the fast spanning tree mode
off, indicates the STP mode is turned off for a particular port
This object is only supported when the Dot1d Protocol is enabled.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.13.1.4 |
agentPortSTPStateThe switch's Port Spanning Tree Protocol State.
This object is only supported when the Dot1d Protocol is enabled.ro Enumeration .1.3.6.1.4.1.4526.11.1.2.13.1.5 |
agentPortAdminModeThe switch's Port Admin Moderw Enumeration .1.3.6.1.4.1.4526.11.1.2.13.1.6 |
agentPortPhysicalModeThe switch's Port Speed Mode. This is the configured physical mode.
This object is read-only for gigabit portsrwobsolete Enumeration .1.3.6.1.4.1.4526.11.1.2.13.1.7 |
agentPortPhysicalStatusThe switch's Port Physical Speed Status. This is the current actual speed.roobsolete Enumeration .1.3.6.1.4.1.4526.11.1.2.13.1.8 |
agentPortLinkTrapModeIf enabled, link up and link down traps will be sent for this port.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.13.1.9 |
agentPortClearStatsclear stats for this port onlyrw Enumeration .1.3.6.1.4.1.4526.11.1.2.13.1.10 |
agentPortDefaultTypeThis object identifies the default administrative port type,
to be used in conjunction with the operational port type
denoted by agentPortType.
The set of possible values for this object is
the same as the set defined for the agentPortType
object.
This object represents the administratively-configured type of
the MAU. If auto-negotiation is not enabled or is not
implemented for this MAU, the value of this object determines
the operational type of the MAU. In this case, a set to this
object will force the MAU into the specified operating mode.
If auto-negotiation is implemented and enabled for this MAU,
the operational type of the MAU is determined by auto-negotiation,
and the value of this object denotes the type to which the MAU
will automatically revert if/when auto-negotiation is later disabled.
The valid values for this object are:
dot3MauType10BaseTHD
dot3MauType10BaseTFD
dot3MauType100BaseTXHD
dot3MauType100BaseTXFD
dot3MauType100BaseFXFD
dot3MauType10GBaseSXrw OBJECT IDENTIFIER .1.3.6.1.4.1.4526.11.1.2.13.1.11 |
agentPortTypeThis object identifies the port type. An initial set of MAU types
are defined in RFC 2668. The assignment of OBJECT IDENTIFIERs to
new types of MAUs is managed by the IANA. If the MAU type is
unknown, the object identifier
unknownMauType OBJECT IDENTIFIER ::= { 0 0 }
is returned. Note that unknownMauType is a syntactically valid
object identifier, and any conformant implementation of ASN.1 and
the BER must be able to generate and recognize this value.
This object represents the operational type of the MAU, as determined
by either (1) the result of the auto-negotiation function or (2) if
auto-negotiation is not enabled or is not implemented for this MAU,
by the value of the object agentPortDefaultType, or (3) for the GigE card
a value determined by the GBIC connected to the card. In case (2), a
set to the object agentPortDefaultType will force the MAU into the
new operating mode.
The valid values for this object are:
dot3MauType10BaseTHD
dot3MauType10BaseTFD
dot3MauType100BaseTXHD
dot3MauType100BaseTXFD
dot3MauType100BaseFXFD
dot3MauType1000BaseSXFD
dot3MauType10GBaseSXro OBJECT IDENTIFIER .1.3.6.1.4.1.4526.11.1.2.13.1.12 |
agentPortAutoNegAdminStatusThis object identifies the administration status of auto negotiation
for this port.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.13.1.13 |
agentPortDot3FlowControlModeConfig flowcontrol allows you to enable or disable
802.3x flow control for this port. This value
applies to only full-duplex mode ports.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.13.1.14 |
agentPortMaxFrameSizeLimitThis object identifies the largest value that can be
configured for agentPortMaxFrameSizero Integer32 .1.3.6.1.4.1.4526.11.1.2.13.1.18 |
agentPortMaxFrameSizeThis object identifies the currently configured maximum frame size
value for this port. The maximmum value that this object can be set
to is the value of agentPortMaxFrameSizeLimit. For Ethernet ports
which support 802.1Q vlan tagging, the minimum value that this object
can be set to is 1522rw Integer32 .1.3.6.1.4.1.4526.11.1.2.13.1.19 |
agentPortBroadcastControlModeIf enabled, broadcast storm recovery will function on this port.
When you specify Enable for Broadcast Storm Recovery and the broadcast
traffic on this Ethernet port exceeds the configured threshold, the
switch blocks (discards) the broadcast traffic.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.13.1.20 |
agentPortBroadcastControlThresholdConfigures the broadcast storm recovery threshold for this port
as a percentage of port speed.rw Integer32 .1.3.6.1.4.1.4526.11.1.2.13.1.21 |
agentPortMulticastControlModeIf enabled, multicast storm recovery will function on this port.
When you specify Enable for Multicast Storm Recovery and the multicast
traffic on this Ethernet port exceeds the configured threshold, the
switch blocks (discards) the multicast traffic.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.13.1.22 |
agentPortMulticastControlThresholdConfigures the multicast storm recovery threshold for this port
as a percentage of port speed.rw Integer32 .1.3.6.1.4.1.4526.11.1.2.13.1.23 |
agentPortUnicastControlModeIf enabled, unicast storm recovery will function on this port.
When you specify Enable for Unicast Storm Recovery and the unknown unicast
traffic on this Ethernet port exceeds the configured threshold, the
switch blocks (discards) the unknown unicast traffic.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.13.1.24 |
agentPortUnicastControlThresholdConfigures the unicast storm recovery threshold for this port
as a percentage of port speed.rw Integer32 .1.3.6.1.4.1.4526.11.1.2.13.1.25 |
agentStpSwitchConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4526.11.1.2.15 |
agentStpConfigDigestKeyThe MST configuration digest key.ro OCTET STRING .1.3.6.1.4.1.4526.11.1.2.15.1 |
agentStpConfigFormatSelectorThe MST configuration format selector. A value other than 0 (zero)
indicates non-support for the IEEE 802.1s standard.ro Unsigned32 .1.3.6.1.4.1.4526.11.1.2.15.2 |
agentStpConfigNameThe MST configuration name of at most 32 characters.rw DisplayString .1.3.6.1.4.1.4526.11.1.2.15.3 |
agentStpConfigRevisionThe MST configuration revision. The default value is 1.rw Unsigned32 .1.3.6.1.4.1.4526.11.1.2.15.4 |
agentStpForceVersionThe MST configuration force protocol version. The default version is dot1s.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.15.5 |
agentStpAdminModeThe spanning tree operational status.
enable(1) - enables spanning tree operational status on the switch.
disable(2) - disables spanning tree operational status on the switch.
The default status is disabled.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.15.6 |
agentStpBpduGuardModeThe spanning tree BPDU Guard Mode.
enable(1) - enables BPDU Guard Mode on the switch.
disable(2) - disables BPDU Guard Mode on the switch.
The default status is disabled.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.15.7 |
agentStpBpduFilterDefaultThe spanning tree BPDU Filter Mode, it enables BPDU Filter on all
edge ports.
enable(1) - enables BPDU Filter Mode on the switch.
disable(2) - disables BPDU Filter Mode on the switch.
The default status is disabled.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.15.8 |
agentStpPortTableSTP port table. SEQUENCE OF AgentStpPortEntry .1.3.6.1.4.1.4526.11.1.2.15.9 |
agentStpPortEntrySTP port entry. AgentStpPortEntry .1.3.6.1.4.1.4526.11.1.2.15.9.1 |
agentStpPortStateThe administrative STP state for the port.
enable(1) - enables STP on the port.
disable(2) - disables STP on the port.
The default port STP state is enabled for the first 4095
ports and disabled for any ports beyond.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.15.9.1.1 |
agentStpPortStatsMstpBpduRxThe MSTP BPDUs received on a specific port.ro Counter32 .1.3.6.1.4.1.4526.11.1.2.15.9.1.2 |
agentStpPortStatsMstpBpduTxThe MSTP BPDUs sent from a specific port.ro Counter32 .1.3.6.1.4.1.4526.11.1.2.15.9.1.3 |
agentStpPortStatsRstpBpduRxThe RSTP BPDUs received on a specific port.ro Counter32 .1.3.6.1.4.1.4526.11.1.2.15.9.1.4 |
agentStpPortStatsRstpBpduTxThe RSTP BPDUs sent from a specific port.ro Counter32 .1.3.6.1.4.1.4526.11.1.2.15.9.1.5 |
agentStpPortStatsStpBpduRxThe STP BPDUs received on a specific port.ro Counter32 .1.3.6.1.4.1.4526.11.1.2.15.9.1.6 |
agentStpPortStatsStpBpduTxThe STP BPDUs sent from a specific port.ro Counter32 .1.3.6.1.4.1.4526.11.1.2.15.9.1.7 |
agentStpPortUpTimeTime since port was reset.
It is displayed in days, hours, minutes, and seconds.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.4526.11.1.2.15.9.1.8 |
agentStpPortMigrationCheckForce the specified port to transmit RSTP or MSTP BPDU's.
Supported values:
false(0) - BPDUs are not to be transmitted.
true(1) - BPDUs are to be transmitted
A non-zero value indicates that BPDUs are to be sent on the specified port.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.15.9.1.9 |
agentStpPortHelloTimeHello time for the STP port. The default value is 2.rw Unsigned32 .1.3.6.1.4.1.4526.11.1.2.15.9.1.10 |
agentStpCstConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4526.11.1.2.15.10 |
agentStpCstHelloTimeThe MSTP root port hello time for the CIST.ro Unsigned32 .1.3.6.1.4.1.4526.11.1.2.15.10.1 |
agentStpCstMaxAgeThe MSTP root port max age for the CIST.ro Unsigned32 .1.3.6.1.4.1.4526.11.1.2.15.10.2 |
agentStpCstRegionalRootIdThe MSTP regional root identifier for the CIST.ro OCTET STRING .1.3.6.1.4.1.4526.11.1.2.15.10.3 |
agentStpCstRegionalRootPathCostThe MSTP regional root path cost for the CIST.ro Unsigned32 .1.3.6.1.4.1.4526.11.1.2.15.10.4 |
agentStpCstRootFwdDelayThe MSTP root port forward delay for the CIST.ro Unsigned32 .1.3.6.1.4.1.4526.11.1.2.15.10.5 |
agentStpCstBridgeFwdDelayThe MSTP bridge forward delay for the CIST. The default value is 15.rw Unsigned32 .1.3.6.1.4.1.4526.11.1.2.15.10.6 |
agentStpCstBridgeHelloTimeThe MSTP bridge hello time for the CIST. The default
value is 2. According to IEEE 802.1Q-REV 2005 updating
hello time is disallowedro Unsigned32 .1.3.6.1.4.1.4526.11.1.2.15.10.7 |
agentStpCstBridgeHoldTimeThe MSTP bridge hold time for the CIST.ro Unsigned32 .1.3.6.1.4.1.4526.11.1.2.15.10.8 |
agentStpCstBridgeMaxAgeThe MSTP bridge max age for the CIST. The default value is 20.rw Unsigned32 .1.3.6.1.4.1.4526.11.1.2.15.10.9 |
agentStpCstBridgeMaxHopsThe MSTP bridge max hops for the CIST. The default value is 20.rw Unsigned32 .1.3.6.1.4.1.4526.11.1.2.15.10.10 |
agentStpCstBridgePriorityThe MSTP bridge priority for the CIST. The default value is 32768.rw Unsigned32 .1.3.6.1.4.1.4526.11.1.2.15.10.11 |
agentStpCstBridgeHoldCountThe MSTP bridge hold count for the CIST. This command sets the value of
maximum bpdus that a bridge is allowed to send within a hello time window.
The default value is 6.rw Unsigned32 .1.3.6.1.4.1.4526.11.1.2.15.10.12 |
agentStpCstTimeSinceTopologyChangeThe MSTP time since the last topology change for the CIST.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.4526.11.1.2.15.10.13 |
agentStpCstTopologyChangeCountThe MSTP count of topology changes for the CIST.ro Counter32 .1.3.6.1.4.1.4526.11.1.2.15.10.14 |
agentStpCstPortTableCIST port table. SEQUENCE OF AgentStpCstPortEntry .1.3.6.1.4.1.4526.11.1.2.15.11 |
agentStpCstPortEntryCIST port entry. AgentStpCstPortEntry .1.3.6.1.4.1.4526.11.1.2.15.11.1 |
agentStpCstPortOperEdgeThe MSTP operational status of a specific port for the CIST.ro Enumeration .1.3.6.1.4.1.4526.11.1.2.15.11.1.1 |
agentStpCstPortOperPointToPointThe MSTP operational point to point mac of a specific port for the CIST.ro Enumeration .1.3.6.1.4.1.4526.11.1.2.15.11.1.2 |
agentStpCstPortTopologyChangeAckThe MSTP topology change acknowledge for a specific port in the CIST.ro Enumeration .1.3.6.1.4.1.4526.11.1.2.15.11.1.3 |
agentStpCstPortEdgeThe administrative state of a specific port in CIST.
enable(1) - enables the port.
disable(2) - disables the port.
The default port state is disabled.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.15.11.1.4 |
agentStpCstPortForwardingStateThe MSTP forwarding state of a specific port in CIST.ro Enumeration .1.3.6.1.4.1.4526.11.1.2.15.11.1.5 |
agentStpCstPortIdThe MSTP port identifier of a specific port in CIST.ro OCTET STRING .1.3.6.1.4.1.4526.11.1.2.15.11.1.6 |
agentStpCstPortPathCostThe MSTP port path cost in CIST. The default value will
correspond to the recommendation specified in IEEE 802.1s Table 13-2
which varies depending upon link speed.rw Unsigned32 .1.3.6.1.4.1.4526.11.1.2.15.11.1.7 |
agentStpCstPortPriorityThe MSTP port priority in CIST. The priority is
in the increments of 16. The default value is 128.rw Unsigned32 .1.3.6.1.4.1.4526.11.1.2.15.11.1.8 |
agentStpCstDesignatedBridgeIdThe MSTP designated bridge ID of a specific port in CIST.ro OCTET STRING .1.3.6.1.4.1.4526.11.1.2.15.11.1.9 |
agentStpCstDesignatedCostThe MSTP designated cost of a specific port in CIST.ro Unsigned32 .1.3.6.1.4.1.4526.11.1.2.15.11.1.10 |
agentStpCstDesignatedPortIdThe MSTP designated port ID of a specific port in CIST.ro OCTET STRING .1.3.6.1.4.1.4526.11.1.2.15.11.1.11 |
agentStpCstExtPortPathCostThe MSTP external port path cost in CIST. The default value varies depending upon the link speed.rw Unsigned32 .1.3.6.1.4.1.4526.11.1.2.15.11.1.12 |
agentStpCstPortBpduGuardEffectBPDU Guard Mode effect on the port.
enable(1) - BPDU Guard Mode is enabled on the port.
disable(2) - BPDU Guard Mode is disabled on the port.ro Enumeration .1.3.6.1.4.1.4526.11.1.2.15.11.1.13 |
agentStpCstPortBpduFilterThis command sets BPDU Filter mode on the port.
enable(1) - BPDU Filter Mode is enabled on the port.
disable(2) - BPDU Filter Mode is disabled on the port.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.15.11.1.14 |
agentStpCstPortBpduFloodThis command sets BPDU Flood mode on the port.
enable(1) - BPDU Flood Mode is enabled on the port.
disable(2) - BPDU Flood Mode is disabled on the port.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.15.11.1.15 |
agentStpCstPortAutoEdgeThis command sets the auto-edge mode of the port which enables it
to become an edge port if it does not see BPDUs for some duration.
enable(1) - enables the auto-edge mode for the port.
disable(2) - disables the auto-edge mode for the port.
The default auto-edge mode is disabled.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.15.11.1.16 |
agentStpCstPortRootGuardThis command sets a port to discard any superior information
received by the port and thus protect against root of the device
from changing.The port gets put into discarding state and does
not forward any packets.
enable(1) - enables the root-guard mode for the port.
disable(2) - disables the root-guard mode for the port.
The default root-guard mode is disabled.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.15.11.1.17 |
agentStpCstPortTCNGuardThis command restricts the port from propagating any topology change
information received through that port.
enable(1) - enables the tcn-guard mode for the port.
disable(2) - disables the tcn-guard mode for the port.
The default tcn-guard mode is disabled.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.15.11.1.18 |
agentStpMstTableMST table. SEQUENCE OF AgentStpMstEntry .1.3.6.1.4.1.4526.11.1.2.15.12 |
agentStpMstEntryMST entry. AgentStpMstEntry .1.3.6.1.4.1.4526.11.1.2.15.12.1 |
agentStpMstIdThe MSTP instance ID.ro Unsigned32 .1.3.6.1.4.1.4526.11.1.2.15.12.1.1 |
agentStpMstBridgePriorityThe MSTP bridge priority in a specific instance. The priority is
in the increments of 4096. The recommended default value is 32768.rw Unsigned32 .1.3.6.1.4.1.4526.11.1.2.15.12.1.2 |
agentStpMstBridgeIdentifierThe MSTP bridge identifier in a specific instance.ro OCTET STRING .1.3.6.1.4.1.4526.11.1.2.15.12.1.3 |
agentStpMstDesignatedRootIdThe MSTP designated root bridge identifier in a specific instance.ro OCTET STRING .1.3.6.1.4.1.4526.11.1.2.15.12.1.4 |
agentStpMstRootPathCostThe MSTP root path cost in a specific instance.ro Unsigned32 .1.3.6.1.4.1.4526.11.1.2.15.12.1.5 |
agentStpMstRootPortIdThe MSTP root port ID in a specific instance.ro OCTET STRING .1.3.6.1.4.1.4526.11.1.2.15.12.1.6 |
agentStpMstTimeSinceTopologyChangeThe MSTP time since the last topology change in a specific instance.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.4526.11.1.2.15.12.1.7 |
agentStpMstTopologyChangeCountThe MSTP count of topology changes in a specific instance.ro Counter32 .1.3.6.1.4.1.4526.11.1.2.15.12.1.8 |
agentStpMstTopologyChangeParmThe MSTP topology change parameter in a specific instance.ro Enumeration .1.3.6.1.4.1.4526.11.1.2.15.12.1.9 |
agentStpMstRowStatusThe MSTP instance status.
Supported values:
active(1) - valid instance.
createAndGo(4) - used to create a new instance.
destroy(6) - removes an instance.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4526.11.1.2.15.12.1.10 |
agentStpMstPortTableMST port table. SEQUENCE OF AgentStpMstPortEntry .1.3.6.1.4.1.4526.11.1.2.15.13 |
agentStpMstPortEntryMST port entry. AgentStpMstPortEntry .1.3.6.1.4.1.4526.11.1.2.15.13.1 |
agentStpMstPortForwardingStateThe MSTP forwarding state of a specific port in a specific instance.ro Enumeration .1.3.6.1.4.1.4526.11.1.2.15.13.1.1 |
agentStpMstPortIdThe MSTP port identifier of a specific port in a specific instance.ro OCTET STRING .1.3.6.1.4.1.4526.11.1.2.15.13.1.2 |
agentStpMstPortPathCostThe MSTP port path cost in a specific instance. The default value will
correspond to the recommendation specified in IEEE 802.1s Table 13-2
which varies depending upon link speed.rw Unsigned32 .1.3.6.1.4.1.4526.11.1.2.15.13.1.3 |
agentStpMstPortPriorityThe MSTP port priority in a specific instance. The priority is
in the increments of 16. The default value is 128.rw Unsigned32 .1.3.6.1.4.1.4526.11.1.2.15.13.1.4 |
agentStpMstDesignatedBridgeIdThe MSTP designated bridge ID of a specific port in a specific instance.ro OCTET STRING .1.3.6.1.4.1.4526.11.1.2.15.13.1.5 |
agentStpMstDesignatedCostThe MSTP designated cost of a specific port in a specific instance.ro Unsigned32 .1.3.6.1.4.1.4526.11.1.2.15.13.1.6 |
agentStpMstDesignatedPortIdThe MSTP designated port ID of a specific port in a specific instance.ro OCTET STRING .1.3.6.1.4.1.4526.11.1.2.15.13.1.7 |
agentStpMstVlanTableMST VLAN table. SEQUENCE OF AgentStpMstVlanEntry .1.3.6.1.4.1.4526.11.1.2.15.14 |
agentStpMstVlanEntryMST VLAN entry. AgentStpMstVlanEntry .1.3.6.1.4.1.4526.11.1.2.15.14.1 |
agentStpMstVlanRowStatusThe association status of an MSTP instance and a VLAN.
Supported values:
active(1) - valid association between an MSTP instance and a VLAN.
createAndGo(4) - used to create a new association between an MSTP instance and a VLAN.
destroy(6) - removes the association between an MSTP instance and a VLAN.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4526.11.1.2.15.14.1.1 |
agentAuthenticationGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4526.11.1.2.16 |
agentAuthenticationListCreateAuthentication List Create
If set to a non empty string, creates a new Authentication List for
configuration.rw DisplayString .1.3.6.1.4.1.4526.11.1.2.16.1 |
agentAuthenticationListTableMST VLAN table. SEQUENCE OF AgentAuthenticationListEntry .1.3.6.1.4.1.4526.11.1.2.16.2 |
agentAuthenticationListEntryMST VLAN entry. AgentAuthenticationListEntry .1.3.6.1.4.1.4526.11.1.2.16.2.1 |
agentAuthenticationListIndexAuthenticaiton List Index
Unique number used for indexing into this table. Unsigned32 .1.3.6.1.4.1.4526.11.1.2.16.2.1.1 |
agentAuthenticationListNameAuthenticaiton List Name
Unique name used to identify the Authentication List from other tables.ro DisplayString .1.3.6.1.4.1.4526.11.1.2.16.2.1.2 |
agentAuthenticationListMethod1Authenticion List Method 1
Configures the first authentication method to use when this list is
specified.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.16.2.1.3 |
agentAuthenticationListMethod2Authenticion List Method 2
Configures the second authentication method to use when this list is
specified.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.16.2.1.4 |
agentAuthenticationListMethod3Authenticion List Method 3
Configures the third authentication method to use when this list is
specified.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.16.2.1.5 |
agentAuthenticationListStatusThe status of the Authentication List.
Supported values:
active(1) - indicates a valid Authenticaiton List
destroy(6) - removes the Authentication List.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4526.11.1.2.16.2.1.6 |
agentAuthenticationListMethod4Authenticion List Method 4
Configures the fourth authentication method to use when this list is
specified.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.16.2.1.7 |
agentUserConfigDefaultAuthenticationListDefault Authentication List
This object configures which authentication list to use for users
which do not have an Authentication List configured. The list
must be configured before setting.rw DisplayString .1.3.6.1.4.1.4526.11.1.2.16.3 |
agentUserAuthenticationConfigTableUser Authentication Config Table SEQUENCE OF AgentUserAuthenticationConfigEntry .1.3.6.1.4.1.4526.11.1.2.16.4 |
agentUserAuthenticationConfigEntryUser Authentication Config Entry AgentUserAuthenticationConfigEntry .1.3.6.1.4.1.4526.11.1.2.16.4.1 |
agentUserAuthenticationListUser Authentication List
This object configures which authentication list to use for this
user. The list must be configured before setting.rw DisplayString .1.3.6.1.4.1.4526.11.1.2.16.4.1.1 |
agentUserPortConfigTableUser Port Config Table SEQUENCE OF AgentUserPortConfigEntry .1.3.6.1.4.1.4526.11.1.2.16.5 |
agentUserPortConfigEntryUser Port Config Entry AgentUserPortConfigEntry .1.3.6.1.4.1.4526.11.1.2.16.5.1 |
agentUserPortSecurityUser Port Port Security
This object configures which ports the user has access to.
Ports are indexed based on dot1dBasePort entries in
dot1dBasePortTable.rw AgentPortMask .1.3.6.1.4.1.4526.11.1.2.16.5.1.1 |
agentClassOfServiceGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4526.11.1.2.17 |
agentClassOfServicePortTableA table that contains information about the 802.1p priority
mapping to traffic class priority queue for every physical port. SEQUENCE OF AgentClassOfServicePortEntry .1.3.6.1.4.1.4526.11.1.2.17.1 |
agentClassOfServicePortEntryA 802.1p priority mapped to a traffic class priority queue. AgentClassOfServicePortEntry .1.3.6.1.4.1.4526.11.1.2.17.1.1 |
agentClassOfServicePortPriorityThe Priority value determined for the received frame.
This value is equivalent to the priority indicated in
the tagged frame received, or one of the evaluated
priorities, determined according to the media-type.
For untagged frames received from Ethernet media, this
value is equal to the dot1dPortDefaultUserPriority value
for the ingress port. INTEGER .1.3.6.1.4.1.4526.11.1.2.17.1.1.1 |
agentClassOfServicePortClassTraffic class priority queue the received frame is mapped to.rw INTEGER .1.3.6.1.4.1.4526.11.1.2.17.1.1.2 |
agentHTTPConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4526.11.1.2.18 |
agentHTTPWebModeConfigures the HTTP server admin moderw Enumeration .1.3.6.1.4.1.4526.11.1.2.18.1 |
agentHTTPJavaModeConfigures the use of the Java interface through Web connections.rw Enumeration .1.3.6.1.4.1.4526.11.1.2.18.2 |
agentHTTPMaxSessionsConfigures the maximum number of allowable HTTP sessions. The default
value is 16.rw Integer32 .1.3.6.1.4.1.4526.11.1.2.18.3 |
agentHTTPHardTimeoutConfigures the hard timeout for HTTP sessions in hours. The default
value is 24 hours. A value of 0 gives an infinite timeout.rw Integer32 .1.3.6.1.4.1.4526.11.1.2.18.4 |
agentHTTPSoftTimeoutConfigures the soft (activity) timeout for HTTP sessions in minutes.
The default value is 5 minutes. A value of 0 gives an infinite timeout.rw Integer32 .1.3.6.1.4.1.4526.11.1.2.18.5 |
agentSystemGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4526.11.1.3 |
agentSaveConfigenable(1) will initiate an configuration save to nvram.
Status is returned by the object agentSaveConfigStatus.rw Enumeration .1.3.6.1.4.1.4526.11.1.3.1 |
agentClearConfigclear config to factory defaultsrw Enumeration .1.3.6.1.4.1.4526.11.1.3.2 |
agentClearLagsclear lag configurationrw Enumeration .1.3.6.1.4.1.4526.11.1.3.3 |
agentClearLoginSessionsclose all telnet sessionsrw Enumeration .1.3.6.1.4.1.4526.11.1.3.4 |
agentClearPasswordsreset passwordsrw Enumeration .1.3.6.1.4.1.4526.11.1.3.5 |
agentClearPortStatsclear all port statisticsrw Enumeration .1.3.6.1.4.1.4526.11.1.3.6 |
agentClearSwitchStatsclear all switch statisticsrw Enumeration .1.3.6.1.4.1.4526.11.1.3.7 |
agentClearTrapLogclear trap logrw Enumeration .1.3.6.1.4.1.4526.11.1.3.8 |
agentClearVlanclear vlan entriesrw Enumeration .1.3.6.1.4.1.4526.11.1.3.9 |
agentResetSystemResets the switch.
This object is not valid for stacking platforms.rw Enumeration .1.3.6.1.4.1.4526.11.1.3.10 |
agentSaveConfigStatusIndicates the current status of an save configuration request.ro Enumeration .1.3.6.1.4.1.4526.11.1.3.11 |
agentCableTesterGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4526.11.1.4 |
agentCableTesterStatusStatus of the Virtual Cable Tester
active(1) - cable testing is in progress. Set to this value
to start the test.
success(2) - A successful test was performed. Cannot be set.
failure(3) - A failure was encountered during the test.
Cannot be set.
uninitialized(4) - No test has been performed yet. Cannot be set.rw Enumeration .1.3.6.1.4.1.4526.11.1.4.1 |
agentCableTesterIfIndexDetermines on which port to perform the cable test. Limited to
copper based ports.rw Unsigned32 .1.3.6.1.4.1.4526.11.1.4.2 |
agentCableTesterCableStatusIndicates the results of the Cable Test.
normal(1) - The cable is working correctly.
open(2) - The cable is disconnected or there is a faulty
connector.
short(3) - There is an electrical short in the cable.
unknown(4) - No test has been performed yet, or a test is
currently in progress.ro Enumeration .1.3.6.1.4.1.4526.11.1.4.3 |
agentCableTesterMinimumCableLengthThe estimated length of the cable in meters. This value
indicates the shortest length estimated. This object will
return 0 if agentCableTesterStatus is not success(2) or the cable
length is unknown.ro Unsigned32 .1.3.6.1.4.1.4526.11.1.4.4 |
agentCableTesterMaximumCableLengthThe estimated length of the cable in meters. This value
indicates the longest length estimated. This object will
return 0 if agentCableTesterStatus is not success(2) or the cable
length is unknown.ro Unsigned32 .1.3.6.1.4.1.4526.11.1.4.5 |
agentCableTesterCableFailureLocationThe estimated distance in meters from the end of the cable to
the failure location. This object will return 0 if
agentCableTesterStatus is not success(2).ro Unsigned32 .1.3.6.1.4.1.4526.11.1.4.6 |