NCRBSC-OPT-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
63
Objects
Active
Status
2
Dependencies
Imported Objects
Objects
63 total| Object Name |
|---|
codex OBJECT IDENTIFIER .1.3.6.1.4.1.449 |
RFC1155-SMI Unknown .1.3.6.1.4.1.449 |
cdxProductSpecific OBJECT IDENTIFIER .1.3.6.1.4.1.449.2 |
cdx6500 OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1 |
cdx6500Configuration OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.2 |
cdx6500CfgProtocolGroup OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.2.1 |
cdx6500PCTPortProtocolGroup OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.2.1.1 |
cdx6500PPCTNCRBisyncTableA table of NCRBSC Port configuration entries. SEQUENCE OF Cdx6500PPCTNCRBisyncEntry .1.3.6.1.4.1.449.2.1.2.1.1.17 |
cdx6500PPCTNCRBisyncEntryA NCRBSC Configuration Table entry. Each entry
contains the configuration parameters for a single
NCRBSC port. Cdx6500PPCTNCRBisyncEntry .1.3.6.1.4.1.449.2.1.2.1.1.17.1 |
cdx6500NCRBSCCfgPortNumberThe NCRBSC port number described by this entry.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.17.1.1 |
cdx6500NCRBSCCfgPADTypeIndicates whether the port is functioning as a
Terminal PAD (TPAD) or a Host PAD (HPAD).
newvalTpad : same functionality as 'tpad', new enumeration
added for RFC1155 compatibility.ro Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.17.1.2 |
cdx6500NCRBSCCfgClockSourceint - internal clock source.
ext - external clock source.
newvalInt - same functionality as 'int', new
enumeration added for RFC1155 compatibility.ro Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.17.1.3 |
cdx6500NCRBSCCfgClockSpeedThis is the speed of the port in bits per second,
when using internal clocking.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.17.1.4 |
cdx6500NCRBSCCfgContentionIndicates whether Half Duplex (hdx) or
Full Duplex (fdx) modem signals are being generated.
Full Duplex indicates communication is occuring
in both directions simultaneously between devices.
Half Duplex indicates transmission is occuring
in both directions, but only in one direction
at a time.
newvalHdx - same functionality as 'hdx', new enumeration
added for RFC1155 compatibility.ro Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.17.1.5 |
cdx6500NCRBSCCfgNumDevicesSpecifies the number of physical devices on this line.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.17.1.6 |
cdx6500NCRBSCCfgServTimerThe Service Timer specifies the interval of time in
seconds between periodic servicing. Such servicing
includes intervals between the time the PAD will
attempt to poll devices that previously failed to
respond and intervals between failures in attempts
to establish a connection from a device configured
for Autocall.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.17.1.7 |
cdx6500NCRBSCCfgErrThreshCountIndicates number of consecutive errors that can occur
before a device is considered down.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.17.1.8 |
cdx6500NCRBSCCfgRetranTimeoutSpecifies the amount of time in TENTHS OF A SECOND before a
retransmission of the previously sent protocol sequence is
attempted. The effective range is 0.1 - 25.5 seconds.
The MINIMUM acceptable values are dependent on the speed
configured as follows (speed - responsetimeout):
1200 - 12, 2400 - 6, 4800 - 3,9600 - 2, 19200 - 2ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.17.1.10 |
cdx6500NCRBSCCfgInterBuffTimeoutSpecifies the maximum amount of time in seconds the PAD
will wait for the end of a multi-packet message from the
network. If this time limit is exceeded, the PAD will
abort the entire message and request retransmission.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.17.1.11 |
cdx6500NCRBSCCfgPortSubAddr0 - 3 Decimal digits
Calls addressed to this node and with this subaddress
will be routed to this port.ro DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.17.1.12 |
cdx6500NCRBSCCfgPortOptionsSelect options on this NCRBSC port as follows:
NONE - no option specified
ORG - Controllers on this port will originate the calls
ACK - DSP End-to-End Acknowledgements are to be used
Any combination of above specified by summing
(e.g. ORG+ACK).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.2.1.1.17.1.13 |
cdx6500NCRBSCCfgRestrictConnDest1 - 32 Decimal digits or a single blank
All calls originating from this port will be routed to
the destination specified in this parameter, irrespective
of route selection table entries. For example, to route
calls to port 1, use P1. To route calls to port 2,
station 4, use P2S4.
Blank this field to disable this function.ro DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.17.1.14 |
cdx6500NCRBSCCfgBillRecThis controls whether billing (accounting) records will
be created for calls on this Device.
newvalOff : same functionality as 'off', new enumeration
added for RFC1155 compatibility.ro Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.17.1.15 |
cdx6500NCRBSCCfgElectricalInterfaceTypeSpecify the Electrical Interface Type:
V.24 - V.24 Electrical Interface Type
V.35 - V.35 Electrical Interface Type
V.36 - V.36 Electrical Interface Type
X.21 - X.21 Electrical Interface Type
NONE - Electrically disabledro Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.17.1.16 |
cdx6500NCRBSCCfgV24ElectricalInterfaceOptionSpecify the Pin 22 option:
RI - V.24 uses Pin 22 for Ring Indicator output signal
TM - V.24 uses Pin 22 for Test Mode input signalro Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.17.1.17 |
cdx6500NCRBSCCfgHighSpeedElectricalInterfaceOptionSpecify the cable type:
NONE - V.35/V.36/X.21 DCE with straight through cable
XOVER - V.35/V.36/X.21 DCE with crossover adapter cablero Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.17.1.18 |
cdx6500PCTNCRBSCDeviceGroup OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.2.1.7 |
cdx6500PBCTNCRBSCDeviceTableA table of NCRBSC device configuration entries. SEQUENCE OF Cdx6500PBCTNCRBSCDeviceEntry .1.3.6.1.4.1.449.2.1.2.1.7.1 |
cdx6500PBCTNCRBSCDeviceEntryA NCRBSC Configuration Table entry. Each entry
contains the configuration parameters for a single
NCRBSC device. Cdx6500PBCTNCRBSCDeviceEntry .1.3.6.1.4.1.449.2.1.2.1.7.1.1 |
cdx6500ncrbscDevPortNumberThe NCRBSC port accessing this devicero INTEGER .1.3.6.1.4.1.449.2.1.2.1.7.1.1.1 |
cdx6500ncrbscDevEntryThe unique number for this specific port.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.7.1.1.2 |
cdx6500ncrbscBSCControlUnitAddr0-2 Hex digits,
This is the Poll address of the Control Unit that supports
this device. It consists of two hexadecimal digits. Valid
ranges depend on device Character Set as follows:
EBCDIC: 40,C1,C2,C3,C4,C5,C6,C7,C8,C9,4A,4B,4C,4D,4E,4F,
50,D1,D2,D3,D4,D5,D6,D7,D8,D9,5A,5B,5C,5D,5E,5F
ASCII : 20,41,42,43,44,45,46,47,48,49,5B,2E,3C,28,2B,21,
26,4A,4B,4C,4D,4E,4F,50,51,52,5D,24,2A,29,3B,5Ero DisplayString .1.3.6.1.4.1.449.2.1.2.1.7.1.1.3 |
cdx6500ncrbscDestControlUnitAddr0-3 Hex digits,
Specifies control unit address on remote PAD. Used with
Connection Request Mode = 2 or 3ro DisplayString .1.3.6.1.4.1.449.2.1.2.1.7.1.1.4 |
cdx6500ncrbscAutocallMnemonic0-2 Hex digits,
This mnemonic name is used if this device is configured
for AUTO or FAST calling.ro DisplayString .1.3.6.1.4.1.449.2.1.2.1.7.1.1.5 |
cdx6500ncrbscDeviceEnabledThis parameter is used to enable or disable the operation
of this controller device.
yes - Enable device.
no - Disable device.
newvalNo - same functionality as 'no', new enumeration
added for RFC1155 compatibility.ro Enumeration .1.3.6.1.4.1.449.2.1.2.1.7.1.1.6 |
cdx6500Statistics OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.3 |
cdx6500StatProtocolGroup OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.3.1 |
cdx6500PSTPortProtocolGroup OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.3.1.1 |
cdx6500PPSTNCRBisyncTableA table of NCRBSC port statistics entries. SEQUENCE OF Cdx6500ncrbscPortStatEntry .1.3.6.1.4.1.449.2.1.3.1.1.17 |
cdx6500ncrbscPortStatEntryA NCRBSC Port Statistic Table entry. Each entry
contains the statistics for a single NCRBSC port. Cdx6500ncrbscPortStatEntry .1.3.6.1.4.1.449.2.1.3.1.1.17.1 |
cdx6500ncrbscStatPortNumberThe NCRBSC port number described by this entry.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.17.1.1 |
cdx6500ncrbscPortStatusPort Status indicates whether or not the port
is switched on and is ready for operation. This value
may be one of :
up - Port is up and running.
down - port is down.
disabled - port has been disabled.
enabled - port has been enabled, but is not yet Up
busyOut - port has been set to be disabled as soon as
last active session is disestablished. No
new sessions will be established.
newvalDisabled - same functionality as 'disabled',
new enumeration added for RFC1155 compatibility.ro Enumeration .1.3.6.1.4.1.449.2.1.3.1.1.17.1.2 |
cdx6500ncrbscPortStatePort State indicates what the port is actually in the
process of doing. This value may be one of :
INACTIVE - H/TPAD port inactive entered during boot.
WTPOLSERVE - TPAD is waiting for response to a poll.
WTSELRESP - TPAD is waiting for the response to a select.
WTDATARESP - H/TPAD is waiting for data to be acknowledged.
DATA - H/TPAD is in the process of sending/receiving
data.
SEL/POL - TPAD is about to select or poll a
controller. This is the most common state
for a TPAD.
SELECT - TPAD is about to select a device.
POLL - TPAD is about to poll a device.
WTENQRESP - H/TPAD is waiting for a NAK response to
an ENQ sent.
IDLE - HPAD is waiting for the host to send commands.
This is the most common state of the HPAD.
WTEOT - HPAD is waiting for an expected EOT from the
host.
FLUSHINGDATA - HPAD encountered an error in the message
received from the host. As a result,
the data is being flushed.
WTLCM - HPAD received a read/modify and is waiting for
the response from the TPAD.ro DisplayString .1.3.6.1.4.1.449.2.1.3.1.1.17.1.3 |
cdx6500ncrbscPortSpeedThis is the speed of the port if clock is internal. If
clock is external, this is the detected clock speed. If
Port Speed is 0, clock is external, but clocking is not
being received from attatched device.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.17.1.4 |
cdx6500ncrbscPortUtilInPercentage of port input bandwidth in use.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.17.1.5 |
cdx6500ncrbscPortUtilOutPercentage of Port output bandwidth in use.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.17.1.6 |
cdx6500ncrbscInMsgsNumber of message received since last node, port, or
statistics reset.ro Counter .1.3.6.1.4.1.449.2.1.3.1.1.17.1.7 |
cdx6500ncrbscOutMsgsNumber of message sent since last node, port, or
statistics reset.ro Counter .1.3.6.1.4.1.449.2.1.3.1.1.17.1.8 |
cdx6500ncrbscInCharsNumber of characters received since last node, port, or
statistics reset.ro Counter .1.3.6.1.4.1.449.2.1.3.1.1.17.1.9 |
cdx6500ncrbscOutCharsNumber of characters sent since last node, port, or
statistics reset.ro Counter .1.3.6.1.4.1.449.2.1.3.1.1.17.1.10 |
cdx6500ncrbscCharRateInNumber of characters received per second.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.17.1.11 |
cdx6500ncrbscCharRateOutNumber of characters sent per second.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.17.1.12 |
cdx6500ncrbscCrcBccErrsNumber of CRC errors since last node, port, or
statistics reset.ro Counter .1.3.6.1.4.1.449.2.1.3.1.1.17.1.13 |
cdx6500ncrbscRviRxAccumulator, received RVI.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.17.1.14 |
cdx6500ncrbscRviTxAccumulator, transmitted RVI.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.17.1.15 |
cdx6500ncrbscWackRxAccumulator, recevied WACK.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.17.1.16 |
cdx6500ncrbscNconvRxMaxMaximum number of conversation messages received
from device within a poll or select.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.17.1.17 |
cdx6500ncrbscNconvTxMaxMaximum number of conversation messages sent to
device within a poll or select.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.17.1.18 |
cdx6500ncrbscNgroupRxMaxMaximum number of grouping messages received
from device within a poll or select.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.17.1.19 |
cdx6500ncrbscNgroupTxMaxMaximum number of grouping messages sent to
device within a poll or select.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.17.1.20 |
cdx6500ncrbscLongRespTimeLongest response timero INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.17.1.21 |
cdx6500ncrbscAverageRespTimeAverage response timero INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.17.1.22 |
cdx6500ncrbscRviForceNumber of RVI's sent to device from the polling algorithm.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.17.1.23 |