MRV-IN-REACH-INTERNET-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for MRV-IN-REACH-INTERNET-MIB.
637
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
637 total| Object Name |
|---|
xInternetDep OBJECT IDENTIFIER .1.3.6.1.4.1.33.4 |
RFC1213-MIB Unknown .1.3.6.1.4.1.33.4 |
xInternet OBJECT IDENTIFIER .1.3.6.1.4.1.33.10 |
xIp OBJECT IDENTIFIER .1.3.6.1.4.1.33.10.1 |
ipGatewayAddress1The internet address of the system's primary (first
choice) gateway. A value of 0.0.0.0 indicates no
address. Corresponds directly to SERVER INTERNET
PRIMARY GATEWAY ADDRESS and the value labeled
'Primary Gateway Address:' in the SERVER INTERNET
CHARACTERISTICS display.rw IpAddress .1.3.6.1.4.1.33.10.1.1 |
ipGatewayAddress2The internet address of the system's secondary
(second choice) gateway. A value of 0.0.0.0
indicates no address. Corresponds directly to
SERVER INTERNET SECONDARY GATEWAY ADDRESS and the
value labeled 'Secondary Gateway Address:' in the
SERVER INTERNET CHARACTERISTICS display.rw IpAddress .1.3.6.1.4.1.33.10.1.2 |
ipAutoSubnetMaskA control for automatic determination of subnet
mask. 'disabled' indicates the system must use the
mask as configured by the network manager.
'enabled' indicates that the system is to
automatically change the subnet mask when the
system's Internet address is changed. Corresponds
directly to SERVER INTERNET SUBNET MASK
AUTOCONFIGURE and the value labeled 'Subnet Mask
Autoconfigure:' in the SERVER INTERNET
CHARACTERISTICS display.rwdeprecated Enumeration .1.3.6.1.4.1.33.10.1.3 |
ipReassemblyA control for reassembly of IP fragments.
Corresponds directly to SERVER INTERNET REASSEMBLY
and the value labeled 'Reassembly:' in the SERVER
INTERNET CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.10.1.4 |
ipFragmentsQueuedHighHighest number of IP fragments queued.ro Gauge .1.3.6.1.4.1.33.10.1.5 |
ipFragmentsQueuedCurrentCurrent number of IP fragments queued.ro Gauge .1.3.6.1.4.1.33.10.1.6 |
ipGenAdExtTableTable of additional fields indexed by local IP
address. An entry in this table is created or
deleted when an entry in the MIB-II ipAddrTable is
created or deleted. Although MIB-II specifies the
ipAddrTable as read-only, MRV In-Reach implementations
typically implement it as read-write to support
modification of local IP addresses, network masks,
and such. SEQUENCE OF IpGenAdExtEntry .1.3.6.1.4.1.33.10.1.7 |
ipGenAdExtEntryA particular entry. IpGenAdExtEntry .1.3.6.1.4.1.33.10.1.7.1 |
ipGenAdEntExtTypeThe way this local IP address is used, which may
imply alternate, more intuitive ways to set it.
primary general purpose for ordinary use
rotary identificaton for rotary selection
slip use for SLIP connection
ppp use for PPP connectionrw Enumeration .1.3.6.1.4.1.33.10.1.7.1.1 |
ipGenAdEntExtBroadcastOutgoing IP broadcast address associated with this
local address. Value may be confined to logical
compatibility with associated network mask.rw IpAddress .1.3.6.1.4.1.33.10.1.7.1.2 |
ipARPTimeoutA control to set the length of time in minutes
before an unused ARP entry is purged from the ARP
table. The default is 60 minutes. Corresponds
directly to the value labeled 'Translation Table TTL'
in the SERVER INTERNET CHARACTERISTICS display.rw INTEGER .1.3.6.1.4.1.33.10.1.8 |
ipGatewayPingIntervalA control to set the interval of time in seconds
between successive pings to the primary gateway
so as to determine its status.
The default is 60 seconds. Corresponds
directly to the value labeled 'Gateway Timeout'
in the SERVER INTERNET CHARACTERISTICS display.rw INTEGER .1.3.6.1.4.1.33.10.1.9 |
ipConfigureBootpControl to use the BOOTP protocol upon startup to learn
the unit's own internet address, subnet mask, primary and
secondary gateway servers, domain name servers, time
server and domain name.rw Enumeration .1.3.6.1.4.1.33.10.1.11 |
xTcp OBJECT IDENTIFIER .1.3.6.1.4.1.33.10.2 |
tcpPortTableA list of TCP character port entries. SEQUENCE OF TcpPortEntry .1.3.6.1.4.1.33.10.2.1 |
tcpPortEntryTCP parameter values for a character port. TcpPortEntry .1.3.6.1.4.1.33.10.2.1.1 |
tcpPortIndexAn index value that uniquely identifies a port.
The port identified by a particular value of this
index is the same port as identified by
charPortIndex in the Proposed Standard Internet
Character MIB.ro INTEGER .1.3.6.1.4.1.33.10.2.1.1.1 |
tcpPortConnectByAddressA control for requesting outgoing connection by
internet address. 'disabled' indicates outgoing
connections must be by Domain name. 'enabled'
indicates that outgoing connections may be requested
by internet address. Corresponds directly to PORT
INTERNET CONNECTIONS and the presence of the label
'Internet Connections' following the label 'Enabled
Characteristics:' in the PORT CHARACTERISTICS
display.rw Enumeration .1.3.6.1.4.1.33.10.2.1.1.2 |
tcpPortWindowSizeSize of the TCP window for TCP connections on the
port. Corresponds directly to PORT INTERNET TCP
WINDOW SIZE and the value labeled 'TCP Window Size:'
in the PORT ALTERNATE CHARACTERISTICS display.rw INTEGER .1.3.6.1.4.1.33.10.2.1.1.3 |
tcpPortKeepAliveLimitNumber of minutes to maintain a TCP connection
without response to keep-alive communication. A
value of zero indicates no limit.rw INTEGER .1.3.6.1.4.1.33.10.2.1.1.4 |
tcpResequencingA control for keeping TCP messages received
out-of-order to resequence them before using them.
Corresponds directly to SERVER INTERNET TCP
RESEQUENCING and the value labeled 'Resequencing:'
in the SERVER INTERNET CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.10.2.2 |
tcpQueuedSegsNumber of TCP segments in the TCP receive queues.
Corresponds directly to the value labeled 'TCP
Packets Queued:' in the SERVER INTERNET COUNTERS
display.ro Gauge .1.3.6.1.4.1.33.10.2.3 |
tcpDiscardSegsNumber of TCP segments discarded due to exceeding
the TCP receive queue limit. Corresponds directly
to the value labeled 'TCP Packets Discarded:' in the
SERVER INTERNET COUNTERS display.ro Counter .1.3.6.1.4.1.33.10.2.4 |
tcpConnectTimerNumber of seconds to attempt a TCP connection
without a response from the other side. The default
value is 32 seconds. Corresponds directly to the
SERVER INTERNET TCP CONNECT TIMER and the value
labeled 'TCP Connect Timer' in the SERVER INTERNET
CHARACTERISTICS displayrw INTEGER .1.3.6.1.4.1.33.10.2.5 |
tcpLocalPortBaseThe value for port 0's tcp source port number.rw INTEGER .1.3.6.1.4.1.33.10.2.6 |
tcpLocalPortIncrementThe value by which the tcp source port number
increases for each port greater than port 0.rw INTEGER .1.3.6.1.4.1.33.10.2.7 |
tcpRoutingTblSzA control to set the size of the working routing table.
The default is the current size of the table (64).rw INTEGER .1.3.6.1.4.1.33.10.2.8 |
tcpDataSendDelayA control to delay for the specified number of 10
millisecond ticks before sending the userdata string
over the telnet connection.rw INTEGER .1.3.6.1.4.1.33.10.2.9 |
tcpAckDelayA Control to prevent sending a TCP ACK when we
we change TCP window size.rw Enumeration .1.3.6.1.4.1.33.10.2.10 |
tcpRetransmitMinNumber of milliseconds for the initial TCP Retransmit
timer. This is the time at which a TCP session will
initially retransmit unacknowledged packets.rw INTEGER .1.3.6.1.4.1.33.10.2.11 |
xSnmpAgent OBJECT IDENTIFIER .1.3.6.1.4.1.33.10.3 |
snmpAgentGetCommunityThe SNMP community name allowed to perform
get-requests or get-next requests to this agent.
Use of this value is case-insensitive. If the size
is 0, the agent does not check the community name
for these operations. Corresponds directly to
SERVER INTERNET SNMP GET COMMUNITY and the value
labeled 'Get Community:' in the SERVER INTERNET SNMP
CHARACTERISTICS display.rw DisplayString .1.3.6.1.4.1.33.10.3.1 |
snmpAgentSetCommunityThe SNMP community name allowed to perform
set-requests to this agent. Use of this value is
case-insensitive. If the size is 0, the agent does
not check the community name for these operations.
Corresponds directly to SERVER INTERNET SNMP SET
COMMUNITY and the value labeled 'Set Community:' in
the SERVER INTERNET SNMP CHARACTERISTICS display.rw DisplayString .1.3.6.1.4.1.33.10.3.2 |
snmpAgentTrapCommunityThe SNMP community name sent in traps from this
agent. Use of this value preserves case.
Corresponds directly to SERVER INTERNET SNMP TRAP
COMMUNITY and the value labeled 'Trap Community:' in
the SERVER INTERNET SNMP CHARACTERISTICS display.rw DisplayString .1.3.6.1.4.1.33.10.3.3 |
snmpAgentGetClientNumberThe number of client source addresses allowed to
perform get-requests or get-next requests to this
agent. If the value is 0, the agent does not check
source address for these operations. Corresponds
indirectly to the values labeled 'Get Client n:' in
the SERVER INTERNET SNMP CHARACTERISTICS display.ro INTEGER .1.3.6.1.4.1.33.10.3.4 |
snmpAgentSetClientNumberThe number of client source addresses allowed to
perform set-requests to this agent. If the value is
0, the agent does not check source address for these
operations. Corresponds indirectly to the values
labeled 'Set Client n:' in the SERVER INTERNET SNMP
CHARACTERISTICS display.ro INTEGER .1.3.6.1.4.1.33.10.3.5 |
snmpAgentTrapClientNumberThe number of client source addresses to which this
agent sends traps. If the value is 0, the agent
does not perform this operation. Corresponds
indirectly to the values labeled 'Trap Client n:' in
the SERVER INTERNET SNMP CHARACTERISTICS display.ro INTEGER .1.3.6.1.4.1.33.10.3.6 |
getClientTableA list of get client entries. The number of
entries is given by the value of
snmpAgentGetClientNumber. SEQUENCE OF GetClientEntry .1.3.6.1.4.1.33.10.3.7 |
getClientEntryParameter values for a get client. GetClientEntry .1.3.6.1.4.1.33.10.3.7.1 |
getClientIndexIdentification of a get client entry. Corresponds
directly to the number in the label 'Get Client n:'
in the SERVER INTERNET SNMP CHARACTERISTICS
display.ro INTEGER .1.3.6.1.4.1.33.10.3.7.1.1 |
getClientEntryStatusStatus of this entry. Setting the value to
'invalid' invalidates the entry. It is an
implementation-specific matter as to whether the
agent removes an invalidated entry from the table.rw Enumeration .1.3.6.1.4.1.33.10.3.7.1.2 |
getClientAddressTypeThe type of network address contained in
getClientAddress. 'unknown' means no address has
been defined. 'other' means no other type value
applies. 'ip' is an Internet IP address.
'ethernet' is an 802.3 MAC address. If
getClientAddressType does not accompany
getClientAddress in a set request, the default type
is 'ip'. Corresponds indirectly to the address
value labeled 'Get Client n:' in the SERVER INTERNET
SNMP CHARACTERISTICS display.rw AddressType .1.3.6.1.4.1.33.10.3.7.1.3 |
getClientAddressThe client's network address. If
getClientAddressType does not accompany
getClientAddress in a set request, the default type
is 'ip'. Corresponds directly to the address value
labeled 'Get Client n:' in the SERVER INTERNET SNMP
CHARACTERISTICS display.rw OCTET STRING .1.3.6.1.4.1.33.10.3.7.1.4 |
setClientTableA list of set client entries. The number of
entries is given by the value of
snmpAgentSetClientNumber. SEQUENCE OF SetClientEntry .1.3.6.1.4.1.33.10.3.8 |
setClientEntryParameter values for a set client. SetClientEntry .1.3.6.1.4.1.33.10.3.8.1 |
setClientIndexIdentification of a set client entry. Corresponds
directly to the number in the label 'Set Client n:'
in the SERVER INTERNET SNMP CHARACTERISTICS
display.ro INTEGER .1.3.6.1.4.1.33.10.3.8.1.1 |
setClientEntryStatusStatus of this entry. Setting the value to
'invalid' invalidates the entry. It is an
implementation-specific matter as to whether the
agent removes an invalidated entry from the table.rw Enumeration .1.3.6.1.4.1.33.10.3.8.1.2 |
setClientAddressTypeThe type of network address contained in
setClientAddress. 'unknown' means no address has
been defined. 'other' means no other type value
applies. 'ip' is an Internet IP address.
'ethernet' is an 802.3 MAC address. If
setClientAddressType does not accompany
setClientAddress in a set request, the default type
is 'ip'. Corresponds indirectly to the address
value labeled 'Set Client n:' in the SERVER INTERNET
SNMP CHARACTERISTICS display.rw AddressType .1.3.6.1.4.1.33.10.3.8.1.3 |
setClientAddressThe client's network address. When setting this
value, the requester must supply
setClientAddressType. If setClientAddressType does
not accompany setClientAddress in a set request, the
default type is 'ip'. Corresponds directly to the
address value labeled 'Set Client n:' in the SERVER
INTERNET SNMP CHARACTERISTICS display.rw OCTET STRING .1.3.6.1.4.1.33.10.3.8.1.4 |
trapClientTableA list of trap client entries. The number of
entries is given by the value of
snmpAgentTrapClientNumber. SEQUENCE OF TrapClientEntry .1.3.6.1.4.1.33.10.3.9 |
trapClientEntryParameter values for a trap client. TrapClientEntry .1.3.6.1.4.1.33.10.3.9.1 |
trapClientIndexIdentification of a trap client entry. Corresponds
directly to the number in the label 'Trap Client n:'
in the SERVER INTERNET SNMP CHARACTERISTICS
display.ro INTEGER .1.3.6.1.4.1.33.10.3.9.1.1 |
trapClientEntryStatusStatus of this entry. Setting the value to
'invalid' invalidates the entry. It is an
implementation-specific matter as to whether the
agent removes an invalidated entry from the table.rw Enumeration .1.3.6.1.4.1.33.10.3.9.1.2 |
trapClientAddressTypeThe type of network address contained in
trapClientAddress. 'unknown' means no address has
been defined. 'other' means no other type value
applies. 'ip' is an Internet IP address.
'ethernet' is an 802.3 MAC address. If
trapClientAddressType does not accompany
trapClientAddress in a set request, the default type
is 'ip'. Corresponds indirectly to the address
value labeled 'Trap Client n:' in the SERVER
INTERNET SNMP CHARACTERISTICS display.rw AddressType .1.3.6.1.4.1.33.10.3.9.1.3 |
trapClientAddressThe client's network address. When setting this
value, the requester must supply
trapClientAddressType. If trapClientAddressType
does not accompany trapClientAddress in a set
request, the default type is 'ip'. Corresponds
directly to the address value labeled 'Trap Client
n:' in the SERVER INTERNET SNMP CHARACTERISTICS
display.rw OCTET STRING .1.3.6.1.4.1.33.10.3.9.1.4 |
snmpAgentAuthFailureAddressThe address of the client to most recently fail
SNMP authorization.ro TypedAddress .1.3.6.1.4.1.33.10.3.10 |
snmpAgentCommunityAuthenticationAlwaysWhen enabled, indicates that community string authentication
is done always for Gets, Sets, and GetNexts. When disabled,
community string authentication is done once; but bypassed
on subsequent Gets, Sets or GetNexts from the same address.rw Enumeration .1.3.6.1.4.1.33.10.3.14 |
snmpAgentTrapClientPingHost1Configures the first trap client in the trapClientTable
as a ping host. The InReach server will poll the ping
host at a specified interval to determine connectivity.
This feature is mutually exclusive with
snmpAgentTrapClientQuerySourceHost1 and
snmpAgentTrapClientQuerySourceHost2.ro Enumeration .1.3.6.1.4.1.33.10.3.15 |
snmpAgentTrapClientPingHost2Configures the second trap client in the trapClientTable
as a ping host. The InReach server will poll the ping
host at a specified interval to determine connectivity.
This feature is mutually exclusive with
snmpAgentTrapClientQuerySourceHost1 and
snmpAgentTrapClientQuerySourceHost2.ro Enumeration .1.3.6.1.4.1.33.10.3.16 |
snmpAgentTrapClientPingHost1PollIntervalIndicates the time in seconds between polling the
first ping host.ro INTEGER .1.3.6.1.4.1.33.10.3.17 |
snmpAgentTrapClientPingHost2PollIntervalIndicates the time in seconds between polling the
second ping host.ro INTEGER .1.3.6.1.4.1.33.10.3.18 |
snmpAgentTrapClientPingHost1PollRetriesIndicates the maximum number of retries when polling
the first ping host before concluding that connectivity
is lost. When network connectivity is lost, PPP dial
backup procedures to a backup host are initiated.ro INTEGER .1.3.6.1.4.1.33.10.3.19 |
snmpAgentTrapClientPingHost2PollRetriesIndicates the maximum number of retries when polling
the second ping host before concluding that connectivity
is lost. When network connectivity is lost, PPP dial
backup procedures to a backup host are initiated.ro INTEGER .1.3.6.1.4.1.33.10.3.20 |
snmpAgentTrapClientQuerySourceHost1Configures the first trap client in the trapClientTable as
a query source host. When enabled the InReach server will
monitor incoming get-, get-next- and set-requests from
this host as an indicator of connectivity. This feature
is mutually exclusive with snmpAgentTrapClientPingHost1
and snmpAgentTrapClientPingHost2.ro Enumeration .1.3.6.1.4.1.33.10.3.21 |
snmpAgentTrapClientQuerySourceHost2Configures the second trap client in the trapClientTable
as a query source host. When enabled the InReach server
will monitor incoming get-, get-next- and set-requests
from this host as an indicator of connectivity. This
feature is mutually exclusive with
snmpAgentTrapClientPingHost1 and
snmpAgentTrapClientPingHost2.ro Enumeration .1.3.6.1.4.1.33.10.3.22 |
snmpAgentTrapClientQuerySourceHost1TimeoutIndicates the time in seconds between SNMP queries
from the first query source host before timing out
and considering connectivity lost to that host. When
network connectivity is lost, PPP dial backup procedures
to a backup host are initiated.ro INTEGER .1.3.6.1.4.1.33.10.3.23 |
snmpAgentTrapClientQuerySourceHost2TimeoutIndicates the time in seconds between SNMP queries
from the first query source host before timing out
and considering connectivity lost to that host. When
network connectivity is lost, PPP dial backup procedures
to a backup host are initiated.ro INTEGER .1.3.6.1.4.1.33.10.3.24 |
xDomainResolver OBJECT IDENTIFIER .1.3.6.1.4.1.33.10.4 |
domainResolverSuffixA partial domain name for the server to append to
the end of an incomplete domain name provided by the
user. Corresponds directly to SERVER INTERNET
DEFAULT DOMAIN SUFFIX and the value labeled 'Domain
Suffix:' in the SERVER INTERNET CHARACTERISTICS
display.rw DisplayString .1.3.6.1.4.1.33.10.4.1 |
domainResolverAddress1The internet address of a Domain Name Server. The
system can use one or two such addresses, without
preference. A value of 0.0.0.0 indicates no
address. Corresponds directly to SERVER INTERNET
PRIMARY DOMAIN ADDRESS and the value labeled
'Primary Domain Address:' in the SERVER INTERNET
CHARACTERISTICS display.rw IpAddress .1.3.6.1.4.1.33.10.4.2 |
domainResolverAddress2The internet address of a Domain Name Server. The
system can use one or two such addresses, without
preference. A value of 0.0.0.0 indicates no
address. Corresponds directly to SERVER INTERNET
SECONDARY DOMAIN ADDRESS and the value labeled
'Secondary Domain Address:' in the SERVER INTERNET
CHARACTERISTICS display.rw IpAddress .1.3.6.1.4.1.33.10.4.3 |
domainResolverTtlThe number of hours to keep received Domain
information. Corresponds directly to SERVER
INTERNET DOMAIN TTL and the value labeled ' Domain
TTL:' in the SERVER INTERNET CHARACTERISTICS
display.rw INTEGER .1.3.6.1.4.1.33.10.4.4 |
domainResolverNameNumberThe number of Domain name mappings in this system's
name cache.ro INTEGER .1.3.6.1.4.1.33.10.4.5 |
nameTableA list of Domain name entries. The number of
entries is given by the value of
domainResolverNameNumber. SEQUENCE OF NameEntry .1.3.6.1.4.1.33.10.4.6 |
nameEntryParameter values for a Domain name. NameEntry .1.3.6.1.4.1.33.10.4.6.1 |
nameNameA fully qualified domain name. Corresponds
directly to the value labeled 'Domain Name' in the
DOMAIN display.ro DisplayString .1.3.6.1.4.1.33.10.4.6.1.1 |
nameAddressAn Internet address corresponding to the Domain
name. Corresponds directly to the value labeled
'Internet Address' in the DOMAIN display.ro IpAddress .1.3.6.1.4.1.33.10.4.6.1.2 |
nameStatusThe status of the entry. Set to 'invalid' to
remove the entry, which corresponds directly to the
PURGE DOMAIN command. Actual removal of the entry
is implementation specific.rw Enumeration .1.3.6.1.4.1.33.10.4.6.1.3 |
nameSourceSource of this entry. The value meanings are:
local defined by manager (LOCAL)
primary obtained from a primary name server
secondary obtained from a secondary name server
rwho obtained from rwho
Corresponds directly to the value labeled 'Source'
in the DOMAIN display.ro Enumeration .1.3.6.1.4.1.33.10.4.6.1.4 |
nameTtlThe number of minutes remaining in the entry's time
to live. Corresponds directly to the value labeled
'TTL' in the DOMAIN display.ro INTEGER .1.3.6.1.4.1.33.10.4.6.1.5 |
domainResolverPpp OBJECT IDENTIFIER .1.3.6.1.4.1.33.10.4.7 |
domainResolverPppPrimaryServerThe internet address of the primary Domain Name Server to
use in PPP IPCP negotiations. A value of 0.0.0.0 indicates
no address. Corresponds directly to the value labeled
'Primary WINS Address:' in the SERVER INTERNET
CHARACTERISTICS display.rw IpAddress .1.3.6.1.4.1.33.10.4.7.1 |
domainResolverPppSecondaryServerThe internet address of the secondary Domain Name Server to
use in PPP IPCP negotiations. A value of 0.0.0.0 indicates
no address. Corresponds directly to the value labeled
'Secondary WINS Address:' in the SERVER INTERNET
CHARACTERISTICS display.rw IpAddress .1.3.6.1.4.1.33.10.4.7.2 |
xSlip OBJECT IDENTIFIER .1.3.6.1.4.1.33.10.5 |
slipTableA list of SLIP character port entries. SEQUENCE OF SlipEntry .1.3.6.1.4.1.33.10.5.1 |
slipEntryParameter values for a SLIP port. SlipEntry .1.3.6.1.4.1.33.10.5.1.1 |
slipIndexAn index value that uniquely identifies a port that
can run SLIP. The port identified by a particular
value of this index is the same port as identified
by charPortIndex in the Proposed Standard Internet
Character MIB.ro INTEGER .1.3.6.1.4.1.33.10.5.1.1.1 |
slipStateA control indicating whether SLIP is in operation
on the port. Corresponds directly to PORT INTERNET
SLIP and the value labeled 'SLIP' in the PORT
CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.10.5.1.1.2 |
slipLocalAddressThe IP address assigned to the port. Corresponds
directly to PORT SLIP ADDRESS and the value labeled
'SLIP Address:' in the PORT ALTERNATE
CHARACTERISTICS display.rw IpAddress .1.3.6.1.4.1.33.10.5.1.1.3 |
slipRemoteAddressThe IP address of the remote system attached to the
port. Corresponds directly to PORT SLIP REMOTE and
the value labeled 'Remote SLIP Address:' in the PORT
ALTERNATE CHARACTERISTICS display.rw IpAddress .1.3.6.1.4.1.33.10.5.1.1.4 |
slipMaskThe subnet mask to use for SLIP operation on the
port. Corresponds directly to PORT SLIP MASK and
the value labeled 'SLIP Mask:' in the PORT ALTERNATE
CHARACTERISTICS display.rw IpAddress .1.3.6.1.4.1.33.10.5.1.1.5 |
slipPortPacketsReceivedThe number of SLIP packets received from the port.
Corresponds directly to the value labeled 'Serial
Packets Received:' in the PORT COUNTERS display.ro Counter .1.3.6.1.4.1.33.10.5.1.1.6 |
slipPortPacketsSentThe number of SLIP packets sent to the port.
Corresponds directly to the value labeled 'Serial
Packets Sent:' in the PORT COUNTERS display.ro Counter .1.3.6.1.4.1.33.10.5.1.1.7 |
slipPortPacketsDiscardedThe number of SLIP packets received from the port
and discarded. Corresponds directly to the value
labeled 'Serial Packets Discarded:' in the PORT
COUNTERS display.ro Counter .1.3.6.1.4.1.33.10.5.1.1.8 |
slipPortPacketLengthErrorsThe number of SLIP packets received from the port
with an incorrect number of bytes. Corresponds
directly to the value labeled 'Serial Packet Length
Errors:' in the PORT COUNTERS display.ro Counter .1.3.6.1.4.1.33.10.5.1.1.9 |
slipPortPacketChecksumErrorsThe number of SLIP packets received from the port
with an invalid checksum. Corresponds directly to
the value labeled 'Serial Packet Checksum Errors:'
in the PORT COUNTERS display.ro Counter .1.3.6.1.4.1.33.10.5.1.1.10 |
slipNetworkPacketsReceivedThe number of SLIP packets received from the
network for this port. Corresponds directly to the
value labeled 'Network Packets Received:' in the
PORT COUNTERS display.ro Counter .1.3.6.1.4.1.33.10.5.1.1.11 |
slipNetworkPacketsSentThe number of SLIP packets sent to the network from
this port. Corresponds directly to the value
labeled 'Network Packets Sent:' in the PORT COUNTERS
display.ro Counter .1.3.6.1.4.1.33.10.5.1.1.12 |
slipNetworkPacketsDiscardedThe number of SLIP packets received from the
network for this port and discarded. Corresponds
directly to the value labeled 'Network Packets
Discarded:' in the PORT COUNTERS display.ro Counter .1.3.6.1.4.1.33.10.5.1.1.13 |
xTelnet OBJECT IDENTIFIER .1.3.6.1.4.1.33.10.6 |
telnetPortTableA list of Telnet character port entries. SEQUENCE OF TelnetPortEntry .1.3.6.1.4.1.33.10.6.1 |
telnetPortEntryTelnet parameter values for a character port. TelnetPortEntry .1.3.6.1.4.1.33.10.6.1.1 |
telnetPortIndexAn index value that uniquely identifies a port.
The port identified by a particular value of this
index is the same port as identified by
charPortIndex in the Proposed Standard Internet
Character MIB.ro INTEGER .1.3.6.1.4.1.33.10.6.1.1.1 |
telnetPortIncomingTcpPortThe TCP port number offered for incoming
connections to this character port. Corresponds
directly to PORT TELNET REMOTE PORT and the value
labeled 'Remote Port:' in the PORT TELNET
CHARACTERISTICS display.rw INTEGER .1.3.6.1.4.1.33.10.6.1.1.2 |
telnetPortOutgoingTcpPortThe TCP port number used by default for outgoing
connections from this character port. Corresponds
directly to PORT TELNET DEFAULT PORT and the value
labeled 'Default Port:' in the PORT TELNET
CHARACTERISTICS display.rw INTEGER .1.3.6.1.4.1.33.10.6.1.1.3 |
telnetPortNewlineTranslationTranslation to apply to newline sequences (CR/NULL
or CR/LF) received from the network, before sending
the newline to the character port. The value
indicates the sequence sent to the character port,
with 'none' meaning no translation. The lfToCrLf
value converts the newline character LF received
from the network to a CR/LF. Corresponds
directly to PORT TELNET NEWLINE FILTERING and the
value labeled 'Newline Filtering:' in the PORT
TELNET CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.10.6.1.1.4 |
telnetPortTerminalTypeThe terminal type character string for Telnet
negotiations. Corresponds directly to PORT TELNET
TERMINALTYPE and the value labeled 'TerminalType:'
in the PORT TELNET CHARACTERISTICS display.rw DisplayString .1.3.6.1.4.1.33.10.6.1.1.5 |
telnetPortEorReflectionControl for end-of-record handshake. Corresponds
directly to PORT TELNET EOR REFLECTION and the value
labeled 'EOR Reflection:' in the PORT TELNET
CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.10.6.1.1.6 |
telnetPortBinaryModeControl for operation of Telnet binary mode. The
value meanings are:
disabled refuse binary mode negotiation
(INTERACTIVE)
flowControl pass all but XON and XOFF (PASTHRU)
complete pass all characters (PASSALL)
Corresponds directly to PORT TELNET BINARY SESSION
MODE and the value labeled 'Binary Session Mode:' in
the PORT TELNET CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.10.6.1.1.7 |
telnetPortSendLocationA control indicating whether a Telnet session will
initiate negotiation of the Send Location option.
Corresponds directly to the PORT TELNET LOCATION and
the value labeled 'Location' in the PORT TELNET
CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.10.6.1.1.8 |
telnetPortClientLocationThe location of the Telnet client port. Corresponds
directly to the value labeled 'Telnet Client
Location' in the SESSION display.ro DisplayString .1.3.6.1.4.1.33.10.6.1.1.9 |
telnetPortPassiveSendLocationA control indicating whether a Telnet session will
passively respond to negotiation of the Send Location
option. When disabled and telnetPortSendLocation is
disabled, we will refuse to negotiate this option.
When telnetPortSendLocation is enabled, it takes
precedence. Corresponds directly to the value labeled
'Passive Location' in the PORT TELNET CHARACTERISTICS
display.rw Enumeration .1.3.6.1.4.1.33.10.6.1.1.10 |
telnetSerialPortTableA list of Telnet character port entries. SEQUENCE OF TelnetSerialPortEntry .1.3.6.1.4.1.33.10.6.2 |
telnetSerialPortEntryTelnet parameter values for a character port. TelnetSerialPortEntry .1.3.6.1.4.1.33.10.6.2.1 |
telnetSerialPortIndexAn index value that uniquely identifies a port.
The port identified by a particular value of this
index is the same port as identified by
charPortIndex in the Proposed Standard Internet
Character MIB.ro INTEGER .1.3.6.1.4.1.33.10.6.2.1.1 |
telnetSerialPortOptionDisplayControl for display of Telnet option negotiations.
Corresponds directly to PORT TELNET OPTION DISPLAY
and the value labeled 'Option Display:' in the PORT
TELNET CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.10.6.2.1.2 |
telnetSerialPortCsiEscapeControl for translation of 8-bit escape sequences
received from the character port to 7-bit
equivalents before transmission to the remote
partner. Corresponds directly to PORT TELNET CSI
ESCAPE and the value labeled 'CSI Escape:' in the
PORT TELNET CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.10.6.2.1.3 |
telnetSerialPortEchoModeControl for who echoes characters that come from
the character port. The value meanings are:
local terminal server echoes locally
remote remote system echoes
disabled don't default to local echo
passive don't initiate negotiating of echo
character initiate remote echo and suppress go ahead
line reject remote echo and reject suppress go ahead
noecho will not initiate echo, but will negotiate it
Corresponds directly to PORT TELNET ECHO MODE and
the value labeled 'Echo Mode:' in the PORT TELNET
CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.10.6.2.1.4 |
telnetSerialPortNewlineModeTranslation to apply to newline (carriage return)
received from the character port, before sending the
newline to the remote partner. The correspondence
to command keywords is 'crNull' to NULL, 'crLF' to
LINEFEED, and 'verbatim' to NOTHING (that is, no
translation). Corresponds directly to PORT TELNET
NEWLINE and the value labeled 'Newline:' in the PORT
TELNET CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.10.6.2.1.5 |
telnetSerialPortTransmitModeCriterion for deciding to send to the remote
partner characters received from the character port.
Corresponds directly to PORT TELNET TRANSMIT and the
value labeled 'Transmit:' in the PORT TELNET
CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.10.6.2.1.6 |
telnetSerialPortTransmitCharacterTimesNumber of character times to wait before
transmitting when telnetSerialPortTransmitMode value
is 'timed'. Corresponds directly to PORT TELNET
TRANSMIT IDLETIME and the value labeled 'Transmit:
Idle Time -' in the PORT TELNET CHARACTERISTICS
display. This object may only be set to values 1..255.
A value of 0 may be read if telnetSerialPortTransmitMode
has a value of immediate or bufferedrw INTEGER .1.3.6.1.4.1.33.10.6.2.1.7 |
telnetSerialPortAbortOutputCharacterCharacter input from the character port to cause
aborting output. The value 0 indicates no character
has this effect. Corresponds directly to PORT
TELNET ABORT OUTPUT and the value labeled 'Abort
Output Character:' in the PORT TELNET
CHARACTERISTICS display.rw INTEGER .1.3.6.1.4.1.33.10.6.2.1.8 |
telnetSerialPortAttentionCharacterCharacter input from the character port to cause an
attention notification to the remote partner. The
value 0 indicates no character has this effect.
Corresponds directly to PORT TELNET ATTENTION and
the value labeled 'Attention Character:' in the PORT
TELNET CHARACTERISTICS display.rw INTEGER .1.3.6.1.4.1.33.10.6.2.1.9 |
telnetSerialPortEraseKeyCharacterCharacter input from the character port to cause
erasure of the previous input character. The value
0 indicates no character has this effect.
Corresponds directly to PORT TELNET ERASE CHARACTER
and the value labeled 'Erase Keystroke Character:'
in the PORT TELNET CHARACTERISTICS display.rw INTEGER .1.3.6.1.4.1.33.10.6.2.1.10 |
telnetSerialPortEraseLineCharacterCharacter input from the character port to cause
erasure of the previous line of input. The value 0
indicates no character has this effect. Corresponds
directly to PORT TELNET ERASE LINE and the value
labeled 'Erase Line Character:' in the PORT TELNET
CHARACTERISTICS display.rw INTEGER .1.3.6.1.4.1.33.10.6.2.1.11 |
telnetSerialPortInterruptCharacterCharacter input from the character port to cause
sending an interrupt notification to the remote
partner. The value 0 indicates no character has
this effect. Corresponds directly to PORT TELNET
INTERRUPT and the value labeled 'Interrupt
Character:' in the PORT TELNET CHARACTERISTICS
display.rw INTEGER .1.3.6.1.4.1.33.10.6.2.1.12 |
telnetSerialPortQueryCharacterCharacter input from the character port to cause
sending a status query to the remote partner. The
value 0 indicates no character has this effect.
Corresponds directly to PORT TELNET QUERY and the
value labeled 'Query Character:' in the PORT TELNET
CHARACTERISTICS display.rw INTEGER .1.3.6.1.4.1.33.10.6.2.1.13 |
telnetSerialPortSynchronizeCharacterCharacter input from the character port to cause
sending a synchronization attempt to the remote
partner. The value 0 indicates no character has
this effect. Corresponds directly to PORT TELNET
SYNCHRONIZE and the value labeled 'Synchronize
Character:' in the PORT TELNET CHARACTERISTICS
display.rw INTEGER .1.3.6.1.4.1.33.10.6.2.1.14 |
telnetSerialPortUrgentBreakControl for encoding breaks as Telnet urgent data.
Corresponds directly to PORT TELNET URGENT BREAK and
the value labeled 'Urgent Break:' in the PORT TELNET
CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.10.6.2.1.15 |
telnetSerialPortRs491A control to enable RS491 protocol processing on a port.rw Enumeration .1.3.6.1.4.1.33.10.6.2.1.16 |
telnetSerialPortTransmitBufferedTimeNumber of milliseconds to wait before transmitting
when telnetSerialPortTransmitMode value is 'timed'.
Corresponds directly to PORT TELNET TRANSMIT BUFFERED
and the value labeled 'Transmit: Buff Time -' in the
PORT TELNET CHARACTERISTICS display. This object may
only be set to values 30..1500. A value of 0 may be
read if telnetSerialPortTransmitMode has a value of
immediate, idletime or controlcharrw INTEGER .1.3.6.1.4.1.33.10.6.2.1.17 |
telnetSerialPortInterpretInterruptAsBreakControl to interpret a Telnet Interrupt Character coming
from the network as a Telnet Break Character, and to send
a break out the serial port. This control is necessary
for those devices which can send Telnet Interrupt but not
Telnet Break. Corresponds directly to the presence of
'Telnet Interrupts Interpreted as Break' under the label
'Enabled Characteristics' in the PORT TELNET
CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.10.6.2.1.18 |
telnetSerialPortPass8dControl to pass unaltered the hexadecimal character '8D'.
This control is added to ensure that this character will
pass through directly in a session with 8-bit characters
and parity odd or even. Corresponds directly to the
presence of 'Telnet Pass 8D' under the label 'Enabled
Characteristics' in the PORT TELNET CHARACTERISTICS
display.rw Enumeration .1.3.6.1.4.1.33.10.6.2.1.19 |
telnetSerialPortComControlClientControl to begin Telnet comport control option negotiations
as a client when a Telnet session is initiated. The comport
control option enables a port to do outbound modem dialing
on a Telnet connection. Corresponds to the value labeled
'Client:' in the PORT TELNET COMPORTCONTROL CHARACTERISTICS
display.rw Enumeration .1.3.6.1.4.1.33.10.6.2.1.20 |
telnetSerialPortComControlServerControl to begin Telnet comport control option negotiations
as a server when a Telnet session is initiated. Corresponds
to the value labeled 'Server:' in the PORT TELNET
COMPORTCONTROL CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.10.6.2.1.21 |
telnetSerialPortComControlServerRaisesDtrControl for the client to request that the server raises
its DTR signal on the port at the begining of the Telnet
connection. Corresponds to the value labeled 'Server
Raises DTR:' in the PORT TELNET COMPORTCONTROL
CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.10.6.2.1.22 |
telnetSerialPortComControlClientTogglesDtrControl to respond to the server's notification that its
DCD has come high (or low) by raising (or lowering) DTR
accordingly on the local port. Corresponds to the value
labeled 'Client Toggles DTR:' in the PORT TELNET
COMPORTCONTROL CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.10.6.2.1.23 |
xTn3270 OBJECT IDENTIFIER .1.3.6.1.4.1.33.10.7 |
tn3270DeviceNumberThe number of entries in the tn3270 Device table.ro INTEGER .1.3.6.1.4.1.33.10.7.1 |
tn3270LanguageNumberThe number of entries in the tn3270 Language
table.ro INTEGER .1.3.6.1.4.1.33.10.7.2 |
tn3270PortKeymapStatusControl for individual ports to create their own
keymaps. Corresponds directly to SERVER TN3270 PORT
KEYMAPS and the value labeled 'Port Keymaps:' in the
SERVER TN3270 display.rw Enumeration .1.3.6.1.4.1.33.10.7.3 |
tn3270DeviceTableA list of tn3270 terminal device entries. SEQUENCE OF Tn3270DeviceEntry .1.3.6.1.4.1.33.10.7.4 |
tn3270DeviceEntryTn3270 parameter values for a terminal device
entry. Tn3270DeviceEntry .1.3.6.1.4.1.33.10.7.4.1 |
tn3270DeviceNameThe name of a generic terminal device. Corresponds
directly to SERVER TN3270 DEVICE and the value
labeled 'Device Name:' in the SERVER TN3270 DEVICE
display.ro DisplayString .1.3.6.1.4.1.33.10.7.4.1.1 |
tn3270DeviceStatusStatus of this entry. Setting the value to
'invalid' invalidates the entry, corresponding
directly to the PURGE SERVER TN3270 DEVICE command.
It is an implementation-specific matter as to
whether the agent removes an invalidated entry from
the table. If a new device table entry is added to
the table, the agent will copy the VT100 table as
a default. If one plans to add a new table entry, one
should not remove the VT100 entry.rw Enumeration .1.3.6.1.4.1.33.10.7.4.1.2 |
tn3270DeviceTypeThe terminal type character string for use when
tn3270DeviceTn3270Type is insufficient. Corresponds
directly to SERVER TN3270 DEVICE TERMINALTYPE and
the value labeled 'TerminalType:' in the SERVER
TN3270 DEVICE display.rw DisplayString .1.3.6.1.4.1.33.10.7.4.1.3 |
tn3270Device3278ModelThe 3278 model for the device. Corresponds
directly to SERVER TN3270 DEVICE 3278Model and the
value labeled '3278Model:' in the SERVER TN3270
DEVICE display.rw Enumeration .1.3.6.1.4.1.33.10.7.4.1.4 |
tn3270DeviceKeyNumberThe number of Key table entries for this device.ro INTEGER .1.3.6.1.4.1.33.10.7.4.1.5 |
tn3270DeviceScreenNumberThe number of Screen table entries for this
device.ro INTEGER .1.3.6.1.4.1.33.10.7.4.1.6 |
tn3270KeyTableA list of tn3270 key entries by device. SEQUENCE OF Tn3270KeyEntry .1.3.6.1.4.1.33.10.7.5 |
tn3270KeyEntryTn3270 parameter values for a key entry for a
device. Tn3270KeyEntry .1.3.6.1.4.1.33.10.7.5.1 |
tn3270KeyDeviceNameThe name of a generic terminal device as in
tn3270DeviceName. Corresponds directly to SERVER
TN3270 DEVICE and the value labeled 'Device Name:'
in the SERVER TN3270 DEVICE display.ro DisplayString .1.3.6.1.4.1.33.10.7.5.1.1 |
tn3270KeyNameThe key name to which this entry applies.
Corresponds directly to the key portion of SERVER
TN3270 DEVICE KEYMAP and the value labeled
'3270-key' in the 'Keymap:' section of the SERVER
TN3270 DEVICE display.ro Enumeration .1.3.6.1.4.1.33.10.7.5.1.2 |
tn3270KeyStatusStatus of this entry. Setting the value to
'invalid' invalidates the entry. It is an
implementation-specific matter as to whether the
agent removes an invalidated entry from the table.rwdeprecated Enumeration .1.3.6.1.4.1.33.10.7.5.1.3 |
tn3270KeyCharacterSequenceThe ASCII character sequence for the key.
Corresponds directly to the escape-sequence portion
of SERVER TN3270 DEVICE KEYMAP and the value labeled
'KeyCode' in the 'Keymap:' section of the SERVER
TN3270 DEVICE display.rw OCTET STRING .1.3.6.1.4.1.33.10.7.5.1.4 |
tn3270KeyDescriptionDescriptive text for the key. Corresponds directly
to the description portion of SERVER TN3270 DEVICE
KEYMAP and the value labeled 'Description' in the
SERVER TN3270 DEVICE display.rw DisplayString .1.3.6.1.4.1.33.10.7.5.1.5 |
tn3270ScreenTableA list of tn3270 screen action entries by device. SEQUENCE OF Tn3270ScreenEntry .1.3.6.1.4.1.33.10.7.6 |
tn3270ScreenEntryTn3270 parameter values for a screen action entry
for a device. Tn3270ScreenEntry .1.3.6.1.4.1.33.10.7.6.1 |
tn3270ScreenDeviceNameThe name of a generic terminal device as in
tn3270DeviceName. Corresponds directly to SERVER
TN3270 DEVICE and the value labeled 'Device Name:'
in the SERVER TN3270 DEVICE display.ro DisplayString .1.3.6.1.4.1.33.10.7.6.1.1 |
tn3270ScreenActionNameThe screen action to which this entry applies.
Corresponds directly to the action portion of SERVER
TN3270 DEVICE SCREENMAP and the value labeled
'Terminal Function' in the 'Screenmap: section of
the SERVER TN3270 DEVICE display.ro Enumeration .1.3.6.1.4.1.33.10.7.6.1.2 |
tn3270ScreenStatusStatus of this entry. Setting the value to
'invalid' invalidates the entry. It is an
implementation-specific matter as to whether the
agent removes an invalidated entry from the table.rwdeprecated Enumeration .1.3.6.1.4.1.33.10.7.6.1.3 |
tn3270ScreenCharacterSequenceThe ASCII character sequence for the screen action.
Some actions may have a lesser length limit.
Corresponds directly to the escape-sequence portion
of SERVER TN3270 DEVICE SCREENMAP and the value
labeled 'HexCode' in the 'Screenmap: section of the
SERVER TN3270 DEVICE display.rw OCTET STRING .1.3.6.1.4.1.33.10.7.6.1.4 |
tn3270LanguageTableA list of tn3270 language entries. SEQUENCE OF Tn3270LanguageEntry .1.3.6.1.4.1.33.10.7.7 |
tn3270LanguageEntryTn3270 parameter values for a language entry. Tn3270LanguageEntry .1.3.6.1.4.1.33.10.7.7.1 |
tn3270LanguageNameThe name of language for character translation
tables. Corresponds directly to SERVER TN3270
LANGUAGE and the value labeled 'Language Name:' in
the SERVER LANGUAGE display.ro DisplayString .1.3.6.1.4.1.33.10.7.7.1.1 |
tn3270LanguageStatusStatus of this entry. Setting the value to
'invalid' invalidates the entry. It is an
implementation-specific matter as to whether the
agent removes an invalidated entry from the table.
If a new device table entry is added to the table,
the agent will copy the USENGLSH table as the default.rw Enumeration .1.3.6.1.4.1.33.10.7.7.1.2 |
eToALanguageTableA list of language EBCDIC to ASCII conversion
entries. SEQUENCE OF EToALanguageEntry .1.3.6.1.4.1.33.10.7.8 |
eToALanguageEntryEBCDIC to ASCII parameter values for a language
entry. EToALanguageEntry .1.3.6.1.4.1.33.10.7.8.1 |
eToALanguageNameThe name of language from the language table.ro DisplayString .1.3.6.1.4.1.33.10.7.8.1.1 |
eToAOffsetEBCDIC character offset plus one, that is, the
value 1 corresponds to an operational offset of 0.
Corresponds directly to the offset portion of SERVER
TN3270 LANGUAGE and the hexadecimal labels around
the conversion table labeled 'EBCDIC to ASCII' in
the SERVER LANGUAGE display.ro INTEGER .1.3.6.1.4.1.33.10.7.8.1.2 |
eToAValueASCII character value for the EBCDIC offset.
Corresponds directly to the value portion of SERVER
TN3270 LANGUAGE and the values in the conversion
table labeled 'EBCDIC to ASCII' in the SERVER
LANGUAGE display.rw INTEGER .1.3.6.1.4.1.33.10.7.8.1.3 |
aToELanguageTableA list of language ASCII to EBCDIC conversion
entries. SEQUENCE OF AToELanguageEntry .1.3.6.1.4.1.33.10.7.9 |
aToELanguageEntryASCII to EBCDIC parameter values for a language
entry. AToELanguageEntry .1.3.6.1.4.1.33.10.7.9.1 |
aToELanguageNameThe name of language from the language table.ro DisplayString .1.3.6.1.4.1.33.10.7.9.1.1 |
aToEOffsetASCII character offset plus one, that is, the value
1 corresponds to an operational offset of 0.
Corresponds directly to the offset portion of SERVER
TN3270 LANGUAGE and the hexadecimal labels around
the conversion table labeled 'ASCII to EBCDIC' in
the SERVER LANGUAGE display.ro INTEGER .1.3.6.1.4.1.33.10.7.9.1.2 |
aToEValueEBCDIC character value for the ASCII offset.
Corresponds directly to the value portion of SERVER
TN3270 LANGUAGE and the values in the conversion
table labeled 'ASCII to EBCDIC' in the SERVER
LANGUAGE display.rw INTEGER .1.3.6.1.4.1.33.10.7.9.1.3 |
tn3270PortTableA list of tn3270 character port entries. SEQUENCE OF Tn3270PortEntry .1.3.6.1.4.1.33.10.7.10 |
tn3270PortEntryParameter values for a tn3270 port. Tn3270PortEntry .1.3.6.1.4.1.33.10.7.10.1 |
tn3270PortIndexAn index value that uniquely identifies a port.
The port identified by a particular value of this
index is the same port as identified by
charPortIndex in the Proposed Standard Internet
Character MIB.ro INTEGER .1.3.6.1.4.1.33.10.7.10.1.1 |
tn3270PortDeviceNameThe name of a generic terminal device from the
tn3270 device table. Corresponds directly to PORT
TELNET TN3270 DEVICE and the value labeled 'Tn3270
Device:' in the PORT TELNET display.rw DisplayString .1.3.6.1.4.1.33.10.7.10.1.2 |
tn3270PortLanguageNameThe name of language from the tn3270 language
table. Corresponds directly to PORT TELNET TN3270
LANGUAGE and the value labeled 'Tn3270 Language:' in
the PORT TELNET display.rw DisplayString .1.3.6.1.4.1.33.10.7.10.1.3 |
tn3270PortExtendedAttributesA control indicating that certain 3270 extended
attributes are supported on the port. Corresponds
directly to PORT TELNET TN3270 XTDATTRS and the
label 'Tn3270 XtdAttrs' following the label 'Enabled
Characteristics' in the PORT TELNET display.rw Enumeration .1.3.6.1.4.1.33.10.7.10.1.4 |
tn3270PortEorNegotiationA control for negotiation of the Telnet EOR option
when establishing a tn3270 session on the port.
Corresponds directly to PORT TELNET TN3270 EOR and
the label 'Tn3270 EOR' following the label 'Enabled
Characteristics' in the PORT TELNET display.rw Enumeration .1.3.6.1.4.1.33.10.7.10.1.5 |
tn3270PortErrorLockA control for requiring use the RESET key when the
host reports an error during a tn3270 session on the
port. Corresponds directly to PORT TELNET TN3270
ERRORLOCK and the label 'Tn3270 ErrorLock' following
the label 'Enabled Characteristics' in the PORT
TELNET display.rw Enumeration .1.3.6.1.4.1.33.10.7.10.1.6 |
tn3270PortPrinterPortThe port number of the tn3270 printer. Corresponds
directly to PORT TELNET TN3270 PRINTER and the value
labeled 'Tn3270 Printer:' in the PORT TELNET
display.rw INTEGER .1.3.6.1.4.1.33.10.7.10.1.7 |
tn3270PortOutgoingTcpPortThe TCP port which is used for a TN3270 session when
connecting to a remote host from this serial port.
Corresponds directly to the value labeled 'Tn3270 Default
Port:' in the PORT TELNET CHARACTERISTICS display.rw INTEGER .1.3.6.1.4.1.33.10.7.10.1.8 |
tn3270PortSpaceInsertControl to allow insert mode within a space filled field, and
write characters over EBCDIC spaces. Corresponds directly to
the presence of 'Tn3270 Space_Insert' under the label 'Enabled
Characteristics' in the PORT TELNET CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.10.7.10.1.9 |
tn3270PortTypeAheadControl to permit typing ahead in a tn3270 session prior to
receiving a response from the host for the previous command
entered. Corresponds directly to the presence of
'Tn3270 TypeAhead' under the label 'Enabled Characteristics'
in the PORT TELNET CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.10.7.10.1.10 |
tn3270PrefixKeyMapControl to prepend a prefix function to another function key.
When the operator hits the key the prepended function(s) and
then the main function for the key are transmitted to the host.
Corresponds directly to the presence of 'Tn3270 PrefixKeyMap'
under the label 'Enabled Characteristics' in the PORT
TELNET CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.10.7.10.1.11 |
tn3270PortScannerIndicates that this is a tn3270 scanner port. Corresponds
directly to the presence of 'Tn3270 SCANNER' under the
label 'Enabled Characteristics' in the PORT TELNET
CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.10.7.10.1.12 |
xKerberos OBJECT IDENTIFIER .1.3.6.1.4.1.33.10.8 |
kerbStatusA control indicating the level of Kerberos
operation on the system. Corresponds directly to
SERVER KERBEROS STATUS and the value labeled
'Kerberos Security:' in the SERVER KERBEROS
display.rw Enumeration .1.3.6.1.4.1.33.10.8.1 |
kerbRealmThe Kerberos realm with which the kerbServerName1
and kerbServerName2 are associated. Corresponds
directly to SERVER KERBEROS REALM and the value
labeled 'Kerberos Realm:' in the SERVER KERBEROS
display.rw DisplayString .1.3.6.1.4.1.33.10.8.2 |
kerbQueryLimitThe maximum number of attempts the system can make
when trying to verify a Kerberos ID. Corresponds
directly to SERVER KERBEROS QUERY LIMIT and the
value labeled 'Kerberos Query Limit:' in the SERVER
KERBEROS display.rw INTEGER .1.3.6.1.4.1.33.10.8.3 |
kerbMasterNameThe Domain name of the Kerberos master host system,
which holds the Kerberos database. Corresponds
directly to SERVER KERBEROS MASTER and the value
labeled 'Kerberos Master:' in the SERVER KERBEROS
display.rw DisplayString .1.3.6.1.4.1.33.10.8.4 |
kerbServerName1The Domain name of the first Kerberos server to try
when the system verifys a Kerberos ID. Corresponds
directly to SERVER KERBEROS PRIMARY SERVER and the
value labeled 'Kerberos Primary Server:' in the
SERVER KERBEROS display.rw DisplayString .1.3.6.1.4.1.33.10.8.5 |
kerbServerName2The Domain name of the Kerberos server to try when
the system verifys a Kerberos ID and cannot reach
the Kerberos primary server. Corresponds directly
to SERVER KERBEROS SECONDARY SERVER and the value
labeled 'Kerberos Secondary Server:' in the SERVER
KERBEROS display.rw DisplayString .1.3.6.1.4.1.33.10.8.6 |
kerbInsecureLoginsThe number of user logins on ports for which
Kerberos user verification is not enabled.
Corresponds directly to the value labeled 'Logins
without Kerberos:' in the SERVER KERBEROS display.ro Counter .1.3.6.1.4.1.33.10.8.7 |
kerbSecureLoginsThe number of successful user logins on ports for
which Kerberos user verification is enabled.
Corresponds directly to the value labeled
'Successful Logins:' in the SERVER KERBEROS
display.ro Counter .1.3.6.1.4.1.33.10.8.8 |
kerbSecureLoginsFailedThe number of verification failures due to
incorrect ID or password for attempted user logins
on ports for which Kerberos user verification is
enabled. Corresponds directly to the value labeled
'Unsuccessful Logins:' in the SERVER KERBEROS
display.ro Counter .1.3.6.1.4.1.33.10.8.9 |
kerbPasswordChangeFailedThe number of user failures to change their
Kerberos password due to invalid old password or new
password verification. Corresponds directly to the
value labeled 'Password Change Failures:' in the
SERVER KERBEROS display.ro Counter .1.3.6.1.4.1.33.10.8.10 |
kerbErrorThe error number of the most recent
Kerberos-related failure. Corresponds directly to
the value labeled 'Last Kerberos Error:' in the
SERVER KERBEROS display. For a list of error
numbers and their meanings, consult relevant MRV In-Reach
or Kerberos documentation.ro INTEGER .1.3.6.1.4.1.33.10.8.11 |
kerbErrorTimeThe date and time that kerbError was last updated.
Corresponds directly to the value labeled
'Occurred:' in the SERVER KERBEROS display.ro DateTime .1.3.6.1.4.1.33.10.8.12 |
kerbMasterAccessThe number of times the system successfully
accessed the Kerberos master host. Corresponds
directly to the value labeled 'Attempts to access:',
'Master', and 'Successful:' in the SERVER KERBEROS
display.ro Counter .1.3.6.1.4.1.33.10.8.13 |
kerbMasterAccessFailedThe number of times the system failed access to the
Kerberos master host. Corresponds directly to the
value labeled 'Attempts to access:', 'Master', and
'Unsuccessful:' in the SERVER KERBEROS display.ro Counter .1.3.6.1.4.1.33.10.8.14 |
kerbServerAccess1The number of times the system successfully
accessed the Kerberos primary server. Corresponds
directly to the value labeled 'Attempts to access:',
'Server1', and 'Successful:' in the SERVER KERBEROS
display.ro Counter .1.3.6.1.4.1.33.10.8.15 |
kerbServerAccessFailed1The number of times the system failed access to the
Kerberos primary server. Corresponds directly to
the value labeled 'Attempts to access:', 'Server1',
and 'Unsuccessful:' in the SERVER KERBEROS
display.ro Counter .1.3.6.1.4.1.33.10.8.16 |
kerbServerAccess2The number of times the system successfully
accessed the Kerberos secondary server. Corresponds
directly to the value labeled 'Attempts to access:',
'Server2', and 'Successful:' in the SERVER KERBEROS
display.ro Counter .1.3.6.1.4.1.33.10.8.17 |
kerbServerAccessFailed2The number of times the system failed access to the
Kerberos secondary server. Corresponds directly to
the value labeled 'Attempts to access:', 'Server2',
and 'Unsuccessful:' in the SERVER KERBEROS
display.ro Counter .1.3.6.1.4.1.33.10.8.18 |
kerbPortTableA list of Kerberos character port entries. SEQUENCE OF KerbPortEntry .1.3.6.1.4.1.33.10.8.19 |
kerbPortEntryParameter values for a Kerberos port. KerbPortEntry .1.3.6.1.4.1.33.10.8.19.1 |
kerbPortIndexAn index value that uniquely identifies a port
could relate to Kerberos. The port identified by a
particular value of this index is the same port as
identified by charPortIndex in the Proposed Standard
Internet Character MIB.ro INTEGER .1.3.6.1.4.1.33.10.8.19.1.1 |
kerbPortStatusA control indicating the level of Kerberos
operation on the port. Corresponds directly to PORT
KERBEROS and the value 'Kerberos' following the
label 'Enabled Characteristics' in the PORT
CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.10.8.19.1.2 |
kerbServerPortThe UDP port number on the Kerberos server where
Kerberos messages are sent.rw Enumeration .1.3.6.1.4.1.33.10.8.20 |
xPortSecurity OBJECT IDENTIFIER .1.3.6.1.4.1.33.10.9 |
psEntryNumberThe number of security entries in this system's
port security table with psEntryStatus of 'valid'.ro INTEGER .1.3.6.1.4.1.33.10.9.1 |
psEntryNumberLimitThe maximum number of security entries in this
system's port security table.ro INTEGER .1.3.6.1.4.1.33.10.9.2 |
psEntryInvalidIndexA value of psEntryIndex for an entry that has
psEntryStatus of 'invalid'. A management station
may choose this value when adding a new entry.
Collisions between independent management stations
simultaneously using the same number are beyond the
scope of this document.ro INTEGER .1.3.6.1.4.1.33.10.9.3 |
psPortTableA list of port security character port entries. SEQUENCE OF PsPortEntry .1.3.6.1.4.1.33.10.9.4 |
psPortEntryPort security parameter values for a port. PsPortEntry .1.3.6.1.4.1.33.10.9.4.1 |
psPortIndexAn index value that uniquely identifies a port for
security purposes. The port identified by a
particular value of this index is the same port as
identified by charPortIndex in the Proposed Standard
Internet Character MIB.ro INTEGER .1.3.6.1.4.1.33.10.9.4.1.1 |
psPortDefaultInboundAccessThe default access to the port for incoming TCP
connections. Corresponds directly to PORT INTERNET
SECURITY DEFAULT INBOUND and the value labeled
'Inbound Default:' in the PORT INTERNET SECURITY
display.rw Enumeration .1.3.6.1.4.1.33.10.9.4.1.2 |
psPortDefaultOutboundAccessThe default access to the port for outgoing TCP
connections. Corresponds directly to PORT INTERNET
SECURITY DEFAULT OUTBOUND and the value labeled
'Outbound Default:' in the PORT INTERNET SECURITY
display.rw Enumeration .1.3.6.1.4.1.33.10.9.4.1.3 |
psClrInternetSecurityA control for if the internet security entries for this
port will be cleared upon port logout. The default is
disabled.rw Enumeration .1.3.6.1.4.1.33.10.9.4.1.4 |
psTableA list of port security entries. SEQUENCE OF PsEntry .1.3.6.1.4.1.33.10.9.5 |
psEntryPort security parameter values for an entry for a
port. PsEntry .1.3.6.1.4.1.33.10.9.5.1 |
psEntryIndexA small, numeric distinguisher for port security
entries. When adding a new entry, the client should
specify an unused value, such as
psEntryInvalidIndex. Corresponds directly to the
value labeled 'Entry' in the SERVER INTERNET
SECURITY display.ro INTEGER .1.3.6.1.4.1.33.10.9.5.1.1 |
psEntryStatusStatus of this entry. Setting the value to
'invalid' invalidates the entry, corresponding
directly to the CLEAR INTERNET SECURITY command. It
is an implementation-specific matter as to whether
the agent removes an invalidated entry from the
table. Setting this object to 'valid' has no effect.
When creating a new instance, one must set
psEntryAddress, psEntryMask, psEntryAccess,
psEntryDirection and psEntryPortList for the new
instance in the same physical set request. Furthermore,
if one wishes to change an entry, one must first
delete it and then add it with its new values.rw Enumeration .1.3.6.1.4.1.33.10.9.5.1.2 |
psEntryAddressThe IP address to which the entry pertains.
Corresponds directly to the PORT INTERNET SECURITY
internet address and the value labeled 'Internet
Address' in the SERVER INTERNET SECURITY display.rw IpAddress .1.3.6.1.4.1.33.10.9.5.1.3 |
psEntryMaskThe mask applied to psEntryAddress when making a
security check based on this entry. Corresponds
directly to PORT INTERNET SECURITY MASK and the
value labeled 'Security Mask' in the SERVER INTERNET
SECURITY display.rw IpAddress .1.3.6.1.4.1.33.10.9.5.1.4 |
psEntryAccessThe access to the port for TCP connections when
making a security check based on this entry.
Corresponds directly to PORT INTERNET SECURITY ALLOW
or DENY and the value labeled 'Access' in the SERVER
INTERNET SECURITY display.rw Enumeration .1.3.6.1.4.1.33.10.9.5.1.5 |
psEntryDirectionThe direction of TCP connections to which this
entry applies. Corresponds directly to PORT
INTERNET SECURITY INBOUND or OUTBOUND and the value
labeled 'Direction' in the SERVER INTERNET SECURITY
display.rw Enumeration .1.3.6.1.4.1.33.10.9.5.1.6 |
psEntryPortMapThe list of character ports to which this entry
applies. The OCTET STRING contains a bitmap, with
one bit for each port, and enough octets for all the
ports on the system. Port numbers are as defined
for charPortIndex in the Proposed Standard Internet
Character MIB. Corresponding bit numbers start with
1 as the high-order bit of the first octet.
Corresponds directly to PORT INTERNET SECURITY and
the value labeled 'Ports' in the SERVER INTERNET
SECURITY display.rw OCTET STRING .1.3.6.1.4.1.33.10.9.5.1.7 |
xXremote OBJECT IDENTIFIER .1.3.6.1.4.1.33.10.10 |
xremoteServerName1The Domain name of the first XREMOTE font server to
try for downloading fonts. Corresponds directly to
SERVER XREMOTE PRIMARY SERVER and the value labeled
'Xremote Primary Font Server:' in the SERVER XREMOTE
display.rw DisplayString .1.3.6.1.4.1.33.10.10.1 |
xremoteServerName2The Domain name of the XREMOTE font server to try
for downloading fonts and the primary font server
does not respond. Corresponds directly to SERVER
XREMOTE SECONDARY SERVER and the value labeled
'Xremote Secondary Font Server:' in the SERVER
XREMOTE display.rw DisplayString .1.3.6.1.4.1.33.10.10.2 |
xremoteServerAccess1The number of times the system successfully
accessed the XREMOTE primary font server.
Corresponds directly to the value labeled 'Attempts
to access:', 'Server1', and 'Successful:' in the
SERVER XREMOTE display.ro Counter .1.3.6.1.4.1.33.10.10.3 |
xremoteServerAccessFailed1The number of times the system failed access to the
XREMOTE primary font server. Corresponds directly
to the value labeled 'Attempts to access:',
'Server1', and 'Unsuccessful:' in the SERVER XREMOTE
display.ro Counter .1.3.6.1.4.1.33.10.10.4 |
xremoteServerAccess2The number of times the system successfully
accessed the XREMOTE secondary font server.
Corresponds directly to the value labeled 'Attempts
to access:', 'Server2', and 'Successful:' in the
SERVER XREMOTE display.ro Counter .1.3.6.1.4.1.33.10.10.5 |
xremoteServerAccessFailed2The number of times the system failed access to the
XREMOTE secondary font server. Corresponds directly
to the value labeled 'Attempts to access:',
'Server2', and 'Unsuccessful:' in the SERVER XREMOTE
display.ro Counter .1.3.6.1.4.1.33.10.10.6 |
xremoteSessionsThe number of connected XREMOTE sessions.
Corresponds directly to the value labeled 'Current
Number of Xremote Sessions:' in the SERVER XREMOTE
display.ro Gauge .1.3.6.1.4.1.33.10.10.7 |
xremotePortTableA list of XREMOTE character port entries. SEQUENCE OF XremotePortEntry .1.3.6.1.4.1.33.10.10.8 |
xremotePortEntryXREMOTE parameter values for a port. XremotePortEntry .1.3.6.1.4.1.33.10.10.8.1 |
xremotePortIndexAn index value that uniquely identifies a port.
The port identified by a particular value of this
index is the same port as identified by
charPortIndex in the Proposed Standard Internet
Character MIB.ro INTEGER .1.3.6.1.4.1.33.10.10.8.1.1 |
xremotePortXremoteControl for use of XREMOTE on the port.
Corresponds directly to PORT XREMOTE and the
presence of the label 'Xremote' following the label
'Enabled Characteristics:' in the PORT
CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.10.10.8.1.2 |
xremotePortXdmQueryThe type of query message issued by a port when
searching for an X Display Manager (XDM).
Corresponds directly to the PORT XDM QUERY and the
'XDM Query:' in the PORT ALTERNATE CHARACTERISTICS
displayrw Enumeration .1.3.6.1.4.1.33.10.10.8.1.3 |
xremotePortXdmHostThe Domain name or Internet address of the X
Display Manager (XDM) for a port. Corresponds
directly to the PORT XDM HOST and the 'XDM Host:' in
the PORT ALTERNATE CHARACTERISTICS displayrw DisplayString .1.3.6.1.4.1.33.10.10.8.1.4 |
xremoteServerClientsThe number of active X clients. Corresponds
directly to the value labeled 'Current Number of
XClients:' in the SERVER XREMOTE display.ro Gauge .1.3.6.1.4.1.33.10.10.9 |
xRotary OBJECT IDENTIFIER .1.3.6.1.4.1.33.10.11 |
rotaryNumberThe number of entries in the Rotary table.ro INTEGER .1.3.6.1.4.1.33.10.11.1 |
rotaryTableA list of rotary entries. SEQUENCE OF RotaryEntry .1.3.6.1.4.1.33.10.11.2 |
rotaryEntryParameter values for a rotary. RotaryEntry .1.3.6.1.4.1.33.10.11.2.1 |
rotaryAddressThe internet address to be recognized as a rotary.
Corresponds directly to the ip-address portion of
SERVER INTERNET ROTARY and the value labeled
'Internet Address' in the SERVER INTERNET ROTARY
display.ro IpAddress .1.3.6.1.4.1.33.10.11.2.1.1 |
rotaryStatusStatus of this entry. Setting the value to
'invalid' invalidates the entry, corresponding
directly to the CLEAR SERVER INTERNET ROTARY
command. It is an implementation-specific matter as
to whether the agent removes an invalidated entry
from the table. Setting the value to 'valid' in
conjunction with a new rotaryAddress will add a
new entry to the table. When adding a new entry,
one should also specify a rotaryPortMap as the DEFVAL
of 0..0 for rotaryPortMap is meaningless.rw Enumeration .1.3.6.1.4.1.33.10.11.2.1.2 |
rotaryPortMapThe list of character ports that compose the
rotary. The OCTET STRING contains a bitmap, with
one bit for each port, and enough octets for all the
ports on the system. Port numbers are as defined
for charPortIndex in the Proposed Standard Internet
Character MIB. Corresponding bit numbers start with
1 as the high-order bit of the first octet.
Corresponds directly to port-list portion of SERVER
INTERNET ROTARY and the value labeled 'Ports' in the
SERVER INTERNET ROTARY display.rw OCTET STRING .1.3.6.1.4.1.33.10.11.2.1.3 |
xEgp OBJECT IDENTIFIER .1.3.6.1.4.1.33.10.12 |
egpRoutingControl for EGP routing services.rw Enumeration .1.3.6.1.4.1.33.10.12.1 |
egpStatusStatus of the EGP routing services indicating why
it is not running.ro Enumeration .1.3.6.1.4.1.33.10.12.2 |
egpNbrTableThe EGP neighbor table. SEQUENCE OF EgpNbrEntry .1.3.6.1.4.1.33.10.12.3 |
egpNbrEntryInformation about this entity's relationship with a
particular EGP neighbor. EgpNbrEntry .1.3.6.1.4.1.33.10.12.3.1 |
egpNbrAddrThe IP address of this entry's EGP neighbor.ro IpAddress .1.3.6.1.4.1.33.10.12.3.1.1 |
egpNbrIntervalDeadThe interval upon entering the cease or idle state
before automatically assuming a Start Event has
occured. If a neighbor does not respond within 5
minutes, a Stop Event will automatically occur. The
interval is in hundredths of seconds.rw INTEGER .1.3.6.1.4.1.33.10.12.3.1.2 |
egpNbrStatusThe status of the entry for this neighbor. Set to
'invalid' to remove the entry.rw Enumeration .1.3.6.1.4.1.33.10.12.3.1.3 |
xOspf OBJECT IDENTIFIER .1.3.6.1.4.1.33.10.13 |
ospfAutoConfigureControl whether OSPF will automatically configure
itself.rw Enumeration .1.3.6.1.4.1.33.10.13.1 |
ospfStatusStatus of the OSPF routing services indicating why
it is not running.ro Enumeration .1.3.6.1.4.1.33.10.13.2 |
ospfIfMtrcTableThe TOS metrics for a non-virtual interface
identified by the interface index. SEQUENCE OF OspfIfMtrcEntry .1.3.6.1.4.1.33.10.13.3 |
ospfIfMtrcEntryA particular TOS metric for a non-virtual interface
identified by the interface index. OspfIfMtrcEntry .1.3.6.1.4.1.33.10.13.3.1 |
ospfIfMtrcIpAddressSame as ospfIfMetricIpAddress in OSPF MIB, the IP
address of this OSPF interface.ro IpAddress .1.3.6.1.4.1.33.10.13.3.1.1 |
ospfIfMtrcAddressLessIfSame as ospfIfMetricAddressLessIf in OSPF MIB, for
the purpose of easing the instancing of addressed
and addressless interfaces. This variable takes the
value 0 on interfaces with IP Addresses, and the
value of ifIndex for interfaces having no IP
Address.ro INTEGER .1.3.6.1.4.1.33.10.13.3.1.2 |
ospfIfMtrcTosSame as ospfIfMetricTOS in OSPF MIB, the type of
service metric being referenced.ro INTEGER ( 1..16 ) .1.3.6.1.4.1.33.10.13.3.1.3 |
ospfIfMtrcCostActualThe actual cost of the metric in case it was set to
auto.ro INTEGER ( 1..65535 ) .1.3.6.1.4.1.33.10.13.3.1.4 |
ospfXIfTableThe TOS metrics for a non-virtual interface
identified by the interface index. SEQUENCE OF OspfXIfEntry .1.3.6.1.4.1.33.10.13.4 |
ospfXIfEntryInterface parameters for OSPF. OspfXIfEntry .1.3.6.1.4.1.33.10.13.4.1 |
ospfXIfIpAddressSame as ospfIfIpAddress in OSPF MIB, the IP address
of this OSPF interface.ro IpAddress .1.3.6.1.4.1.33.10.13.4.1.1 |
ospfXIfAddressLessIfSame as ospfIfAddressLessIf in OSPF MIB, for the
purpose of easing the instancing of addressed and
addressless interfaces. This variable takes the
value 0 on interfaces with IP Addresses, and the
value of ifIndex for interfaces having no IP
Address.ro INTEGER .1.3.6.1.4.1.33.10.13.4.1.2 |
ospfXIfTypeActualThe interface type.ro Enumeration .1.3.6.1.4.1.33.10.13.4.1.3 |
ospfXIfStatusThe status of the interface entry, including the
entry in the standard OSPF MIB. Set to 'invalid' to
remove the entry.rw Enumeration .1.3.6.1.4.1.33.10.13.4.1.4 |
ospfXAreaTableParameters for an OSPF area. SEQUENCE OF OspfXAreaEntry .1.3.6.1.4.1.33.10.13.5 |
ospfXAreaEntryAn area entry. OspfXAreaEntry .1.3.6.1.4.1.33.10.13.5.1 |
ospfXAreaIdSame as ospfAreaId in OSPF MIB, the ID of the
area.ro IpAddress .1.3.6.1.4.1.33.10.13.5.1.1 |
ospfXAreaStatusThe status of the area entry, including the entry
in the standard OSPF MIB. Set to 'invalid' to
remove the entry.rw Enumeration .1.3.6.1.4.1.33.10.13.5.1.2 |
xRouterIp OBJECT IDENTIFIER .1.3.6.1.4.1.33.10.14 |
ipAdExtTableTable of additional fields indexed by local IP
address. An entry in this table is created or
deleted when an entry in the ipAddrTable is created
or deleted. SEQUENCE OF IpAdExtEntry .1.3.6.1.4.1.33.10.14.1 |
ipAdExtEntryA particular entry. IpAdExtEntry .1.3.6.1.4.1.33.10.14.1.1 |
ipAdEntExtAddressSame as ipAdEntAddr, a local address representing a
network connection.ro IpAddress .1.3.6.1.4.1.33.10.14.1.1.1 |
ipAdEntExtProxyArpControls whether proxy ARP is active for this local
address.rw Enumeration .1.3.6.1.4.1.33.10.14.1.1.2 |
ipAdEntExtRipControls whether RIP as a router discovery protocol
is active for this local address.rodeprecated Enumeration .1.3.6.1.4.1.33.10.14.1.1.3 |
ipRouterIfTableTable of IP router values indexed by interface. SEQUENCE OF IpRouterIfEntry .1.3.6.1.4.1.33.10.14.2 |
ipRouterIfEntryA particular entry. IpRouterIfEntry .1.3.6.1.4.1.33.10.14.2.1 |
ipRouterIfIndexThe index of the interface; same as IfIndex.ro INTEGER .1.3.6.1.4.1.33.10.14.2.1.1 |
ipRouterIfProtocolPriorityThe priority at which all Internet routed packets
will be placed on the WAN output queue.rw Enumeration .1.3.6.1.4.1.33.10.14.2.1.2 |
ipRouterIfMTUThe size of the largest datagram that IP can
transmit on this interface. The default value
is actually hardware dependent.rw INTEGER .1.3.6.1.4.1.33.10.14.2.1.3 |
ipRouterIfRDPControl for whether the router side of the Router
Discovery Protocol is running on this interface.rw Enumeration .1.3.6.1.4.1.33.10.14.2.1.4 |
ipRouterIfArpPacketsInThe number of ARP packets received on this
interface.ro Counter .1.3.6.1.4.1.33.10.14.2.1.5 |
ipRouterIfArpPacketsOutThe number of ARP packets sent on this interface.ro Counter .1.3.6.1.4.1.33.10.14.2.1.6 |
ipRouterIfPacketsInThe number of IP packets received on this
interface.ro Counter .1.3.6.1.4.1.33.10.14.2.1.7 |
ipRouterIfPacketsOutThe number of IP packets sent on this interface.ro Counter .1.3.6.1.4.1.33.10.14.2.1.8 |
ipRouterIfForwardsInThe number of IP packets received on this interface
that were forwarded.ro Counter .1.3.6.1.4.1.33.10.14.2.1.9 |
ipRouterIfForwardsOutThe number of IP packets sent on this interface
that were forwarded.ro Counter .1.3.6.1.4.1.33.10.14.2.1.10 |
xIpTraffic OBJECT IDENTIFIER .1.3.6.1.4.1.33.10.14.3 |
ipTrafficSortSetting to 'execute' causes the most recent traffic
information to be sorted into the ipTrafficTable.
The sorting precedence is: decreasing percentage,
increasing destination address, increasing source
address, and increasing interface number. Setting
to 'ready' has no effect.rw Enumeration .1.3.6.1.4.1.33.10.14.3.1 |
ipTrafficTableA list of traffic entries, sorted in the order
specified by ipTrafficSort. SEQUENCE OF IpTrafficEntry .1.3.6.1.4.1.33.10.14.3.2 |
ipTrafficEntryA traffic entry. IpTrafficEntry .1.3.6.1.4.1.33.10.14.3.2.1 |
ipTrafficIndexIdentification of this traffic entry.ro INTEGER .1.3.6.1.4.1.33.10.14.3.2.1.1 |
ipTrafficPercentThe percentage of total traffic that this traffic
entry represents, in tenths of a percent.ro INTEGER .1.3.6.1.4.1.33.10.14.3.2.1.2 |
ipTrafficDstAddrThe destination IP address of the traffic entry.ro IpAddress .1.3.6.1.4.1.33.10.14.3.2.1.3 |
ipTrafficSrcAddrThe source IP address of the traffic entry.ro IpAddress .1.3.6.1.4.1.33.10.14.3.2.1.4 |
ipTrafficProtocolThe IP protocol type of the traffic entry.ro INTEGER ( 0..255 ) .1.3.6.1.4.1.33.10.14.3.2.1.5 |
ipTrafficDstPortThe destination TCP/UDP port of the traffic
entry.ro INTEGER ( 0..65535 ) .1.3.6.1.4.1.33.10.14.3.2.1.6 |
ipTrafficSrcPortThe source TCP/UDP port of the traffic entry.ro INTEGER ( 0..65535 ) .1.3.6.1.4.1.33.10.14.3.2.1.7 |
ipTrafficIfThe inbound interface to which the traffic entry
applies. This value is the same as IfIndex.ro INTEGER .1.3.6.1.4.1.33.10.14.3.2.1.8 |
ipTrafficMonitoringControl for whether the router side of the Router
Discovery Protocol is running on this interface.rw Enumeration .1.3.6.1.4.1.33.10.14.3.3 |
xIpNetToMediaTableMRV In-Reach extensions to the IP Address Translation
Table. SEQUENCE OF XIpNetToMediaEntry .1.3.6.1.4.1.33.10.14.4 |
xIpNetToMediaEntryEntry parameters. XIpNetToMediaEntry .1.3.6.1.4.1.33.10.14.4.1 |
xIpNetToMediaCircuitAn additional identifier for the circuit (i.e.
Frame Relay DLCI or X.25 VC) which the entry
extends.rw INTEGER .1.3.6.1.4.1.33.10.14.4.1.1 |
xIpNetToMediaReverseArpWhether reverse ARP is supported on this entry.rw Enumeration .1.3.6.1.4.1.33.10.14.4.1.2 |
xRouterUdp OBJECT IDENTIFIER .1.3.6.1.4.1.33.10.15 |
udpBcstServerTableTable of servers to whom UDP broadcast messages
will be forwarded. SEQUENCE OF UdpBcstServerEntry .1.3.6.1.4.1.33.10.15.1 |
udpBcstServerEntryA particular entry. UdpBcstServerEntry .1.3.6.1.4.1.33.10.15.1.1 |
udpBcstServerAddressInternet address of the server.ro IpAddress .1.3.6.1.4.1.33.10.15.1.1.1 |
udpBcstServerStatusThe status of the server. Set to 'invalid' to
remove the entry.rw Enumeration .1.3.6.1.4.1.33.10.15.1.1.2 |
udpBcstPortTableTable of incoming UDP destination port numbers for
which UDP broadcasts will be forwarded. SEQUENCE OF UdpBcstPortEntry .1.3.6.1.4.1.33.10.15.2 |
udpBcstPortEntryA particular entry. UdpBcstPortEntry .1.3.6.1.4.1.33.10.15.2.1 |
udpBcstPortThe incoming destination UDP port number.ro INTEGER .1.3.6.1.4.1.33.10.15.2.1.1 |
udpBcstPortStatusThe status of broadcast forwarding for the port.
Set to 'invalid' to remove the entry.rw Enumeration .1.3.6.1.4.1.33.10.15.2.1.2 |
udpBcstRoutingThe indication of whether this entity forwards UDP
broadcasts.rw Enumeration .1.3.6.1.4.1.33.10.15.3 |
xRouterPolicy OBJECT IDENTIFIER .1.3.6.1.4.1.33.10.16 |
xImport OBJECT IDENTIFIER .1.3.6.1.4.1.33.10.16.1 |
impEgpRuleTableThe EGP import table. SEQUENCE OF ImpEgpRuleEntry .1.3.6.1.4.1.33.10.16.1.1 |
impEgpRuleEntryAn EGP import rule. Each rule is keyed by the
Autonomous System of the EGP neighbor and the IP
network of the route learned from the neighbor.
The AS can be set to a wild card as can the IP
network. When a route is learned from a neighbor,
the most specific import rule is applied to the
route. The route is either accepted or discarded
and its metrics are applied according to the rule.
An exact match on the AS and IP network is the most
exact rule. An exact match on the AS and a wild
card match on the IP network is the 2nd most exact
rule. A wild card match on the AS and an exact match
on the IP network is the 3rd most exact match.
Finally, a total wild card match is the least exact
rule. ImpEgpRuleEntry .1.3.6.1.4.1.33.10.16.1.1.1 |
impEgpRuleAsThe Autonomous System of the neighbor. The value
65535 is a wild card matching any AS number.ro INTEGER ( 0..65535 ) .1.3.6.1.4.1.33.10.16.1.1.1.1 |
impEgpRuleNetworkThe IP network learned from the neighbor. The
value 255.255.255.255 is a wild card matching any
network.ro IpAddress .1.3.6.1.4.1.33.10.16.1.1.1.2 |
impEgpRuleActionControl whether the route is learned or
discarded.rw Enumeration .1.3.6.1.4.1.33.10.16.1.1.1.3 |
impEgpRulePreferencePreference to be stored with the route. The lower
preference is preferred.rw INTEGER ( 1..255 ) .1.3.6.1.4.1.33.10.16.1.1.1.4 |
impEgpRuleTypeType to be stored with the route. The type is based
on the OSPF external type and used to help compare
metrics. Type 1 is preferred over type 2.rw INTEGER ( 1..2 ) .1.3.6.1.4.1.33.10.16.1.1.1.5 |
impEgpRuleMetricActionHow to apply the impEgpRuleMetric field to the
metric learned with the route before storing it in
the routing table.rw Enumeration .1.3.6.1.4.1.33.10.16.1.1.1.6 |
impEgpRuleMetricMetric value to be applied to the metric learned
learned with the route before storing it in the
routing table.rw INTEGER .1.3.6.1.4.1.33.10.16.1.1.1.7 |
impEgpRuleStatusThe status of the rule. Set to 'invalid' to remove
the rule. If the all wild card rule is removed, it
is automatically readded with default values.rw Enumeration .1.3.6.1.4.1.33.10.16.1.1.1.8 |
impOspfRuleTableThe OSPF import table. SEQUENCE OF ImpOspfRuleEntry .1.3.6.1.4.1.33.10.16.1.2 |
impOspfRuleEntryAn OSPF import rule. Each rule is keyed by the IP
network of the route and the AS from which it was
learned. The Ip network and the AS can both be set
to a wild card. When an OSPF route is added to the
routing table, the most specific import rule is
applied to set the preference of the route. An
exact match on the Ip network and on the AS is the
most exact rule. An exact match on the IP network
and a wild card match on the AS is the 2nd most
exact rule. A wild card match on both the on the
AS and IP network is the next and least exact
rule. ImpOspfRuleEntry .1.3.6.1.4.1.33.10.16.1.2.1 |
impOspfRuleNetworkThe IP network of the route. The value
255.255.255.255 is a wild card matching any
network.ro IpAddress .1.3.6.1.4.1.33.10.16.1.2.1.1 |
impOspfRulePreferencePreference to be stored with the route. The lower
preference is preferred.rw INTEGER ( 1..255 ) .1.3.6.1.4.1.33.10.16.1.2.1.2 |
impOspfRuleStatusThe status of the rule. Set to 'invalid' to remove
the rule. If the all wild card rule is removed, it
is automatically readded with default values.rw Enumeration .1.3.6.1.4.1.33.10.16.1.2.1.3 |
impRipRuleTableThe RIP import table. SEQUENCE OF ImpRipRuleEntry .1.3.6.1.4.1.33.10.16.1.3 |
impRipRuleEntryA RIP import rule. Each rule is keyed by the
interface and the IP network of the route learned
from the neighbor. The route is either accepted or
discarded and its metrics are applied according to
the rule. An exact match on the IP network is the
rule that will be applied. If an exact match does
not exist, the rule with the wild card IP network is
used. ImpRipRuleEntry .1.3.6.1.4.1.33.10.16.1.3.1 |
impRipRuleFromIfThe interface index of the interface where the rule
applies, same as ifIndex.ro IpAddress .1.3.6.1.4.1.33.10.16.1.3.1.1 |
impRipRuleNetworkThe IP network learned from the neighbor. The
value 255.255.255.255 is a wild card matching any
network.ro IpAddress .1.3.6.1.4.1.33.10.16.1.3.1.2 |
impRipRuleActionControl whether the route is learned or
discarded.rw Enumeration .1.3.6.1.4.1.33.10.16.1.3.1.3 |
impRipRulePreferencePreference to be stored with the route. The lower
preference are preferred.rw INTEGER ( 0..255 ) .1.3.6.1.4.1.33.10.16.1.3.1.4 |
impRipRuleTypeType to be stored with the route. The type is based
on the OSPF external type and used to help compare
metrics. Type 1 is preferred over type 2.rw INTEGER ( 1..2 ) .1.3.6.1.4.1.33.10.16.1.3.1.5 |
impRipRuleMetricActionHow to apply the impRipRuleMetric field to the
metric learned with the route before storing it in
the routing table.rw Enumeration .1.3.6.1.4.1.33.10.16.1.3.1.6 |
impRipRuleMetricMetric value to be applied to the metric learned
learned with the route before storing it in the
routing table.rw INTEGER .1.3.6.1.4.1.33.10.16.1.3.1.7 |
impRipRuleStatusThe status of the rule. Set to 'invalid' to remove
the rule. If the all wild card rule is removed, it
is automatically readded with default values.rw Enumeration .1.3.6.1.4.1.33.10.16.1.3.1.8 |
impIsisRuleTableThe Isis import table. SEQUENCE OF ImpIsisRuleEntry .1.3.6.1.4.1.33.10.16.1.4 |
impIsisRuleEntryAn Isis import rule. Each rule is keyed by the IP
network of the route learned from the neighbor. The
route is either accepted or discarded and its metrics
are applied according to the rule. An exact match on the
IP network is the rule that will be applied. If an exact
match does not exist, the rule with the wild card IP
network is used. ImpIsisRuleEntry .1.3.6.1.4.1.33.10.16.1.4.1 |
impIsisRuleNetworkThe IP network learned from the neighbor. The value
255.255.255.255 is a wild card matching any network.ro IpAddress .1.3.6.1.4.1.33.10.16.1.4.1.1 |
impIsisRuleActionControl whether the route is learned or discarded.rw Enumeration .1.3.6.1.4.1.33.10.16.1.4.1.2 |
impIsisRulePreferencePreference to be stored with the route. The lower
preference are preferred.rw INTEGER ( 0..255 ) .1.3.6.1.4.1.33.10.16.1.4.1.3 |
impIsisRuleTypeType to be stored with the route. The type is based on
the OSPF external type and used to help compare metrics.
Type 1 is preferred over type 2.rw INTEGER ( 1..2 ) .1.3.6.1.4.1.33.10.16.1.4.1.4 |
impIsisRuleMetricActionHow to apply the impIsisRuleMetric field to the metric
learned with the route before storing it in the routing
table.rw Enumeration .1.3.6.1.4.1.33.10.16.1.4.1.5 |
impIsisRuleMetricMetric value to be applied to the metric learned learned
with the route before storing it in the routing table.rw INTEGER .1.3.6.1.4.1.33.10.16.1.4.1.6 |
impIsisRuleStatusThe status of the rule. Set to 'invalid' to remove
the rule. If the all wild card rule is removed, it is
automatically readded with default values.rw Enumeration .1.3.6.1.4.1.33.10.16.1.4.1.7 |
xExport OBJECT IDENTIFIER .1.3.6.1.4.1.33.10.16.2 |
expEgpToEgpRuleTableThe EGP to EGP export table. SEQUENCE OF ExpEgpToEgpRuleEntry .1.3.6.1.4.1.33.10.16.2.1 |
expEgpToEgpRuleEntryAn EGP to EGP export rule. Each rule is keyed by
the Autonomous System of the EGP neighbor, the IP
network of the EGP route in the routing table, and
the Autonomous System from which the route was
learned. The neighbor (to) AS can be set to a wild
card as can the IP network and the (from) AS. The
route is either accepted to be advertised to the
neighbor or discarded from being advertised, and its
metric is applied according to the rule. The best
match is as follows:
To As IP Network From AS Rank
exact exact exact 1st
exact exact wild card 2nd
exact wild card exact 3rd
exact wild card wild card 4th
wild card exact exact 5th
wild card exact wild card 6th
wild card wild card exact 7th
wild card wild card wild card 8th ExpEgpToEgpRuleEntry .1.3.6.1.4.1.33.10.16.2.1.1 |
expEgpToEgpRuleToAsThe Autonomous System of the neighbor. The value
65535 is a wild card matching any AS number.ro INTEGER ( 0..65535 ) .1.3.6.1.4.1.33.10.16.2.1.1.1 |
expEgpToEgpRuleNetworkThe IP network of the route in the route table.
The value 255.255.255.255 is a wild card matching
any network.ro IpAddress .1.3.6.1.4.1.33.10.16.2.1.1.2 |
expEgpToEgpRuleFromAsThe Autonomous System of the route in the route
table. The value 65535 is a wild card matching any
AS number.ro INTEGER ( 0..65535 ) .1.3.6.1.4.1.33.10.16.2.1.1.3 |
expEgpToEgpRuleActionControl whether the route is advertised or not.rw Enumeration .1.3.6.1.4.1.33.10.16.2.1.1.4 |
expEgpToEgpRuleMetricActionHow to apply the expEgpToEgpRuleMetric field to the
metric in the route table entry before the route is
advertised.rw Enumeration .1.3.6.1.4.1.33.10.16.2.1.1.5 |
expEgpToEgpRuleMetricMetric value to be applied to the metric in the
route table entry before the route is advertised.rw INTEGER .1.3.6.1.4.1.33.10.16.2.1.1.6 |
expEgpToEgpRuleStatusThe status of the rule. Set to 'invalid' to remove
the rule. If the all wild card rule is removed, it
is automatically readded with default values.rw Enumeration .1.3.6.1.4.1.33.10.16.2.1.1.7 |
expOspfToEgpRuleTableThe OSPF to EGP export table. SEQUENCE OF ExpOspfToEgpRuleEntry .1.3.6.1.4.1.33.10.16.2.2 |
expOspfToEgpRuleEntryAn OSPF to EGP export rule. Each rule is keyed by
the Autonomous System of the EGP neighbor, the IP
network of the OSPF route in the routing table, and
the Autonomous System from which the route was
learned. The neighbor (to) AS can be set to a wild
card as can the IP network and the (from) AS. The
route is either accepted to be advertised to the
neighbor or discarded from being advertised, and its
metric is applied according to the rule. The best
match is as follows:
To As IP Network From AS Rank
exact exact exact 1st
exact exact wild card 2nd
exact wild card exact 3rd
exact wild card wild card 4th
wild card exact exact 5th
wild card exact wild card 6th
wild card wild card exact 7th
wild card wild card wild card 8th ExpOspfToEgpRuleEntry .1.3.6.1.4.1.33.10.16.2.2.1 |
expOspfToEgpRuleToAsThe Autonomous System of the neighbor. The value
65535 is a wild card matching any AS number.ro INTEGER ( 0..65535 ) .1.3.6.1.4.1.33.10.16.2.2.1.1 |
expOspfToEgpRuleNetworkThe IP network of the route in the route table.
The value 255.255.255.255 is a wild card matching
any network.ro IpAddress .1.3.6.1.4.1.33.10.16.2.2.1.2 |
expOspfToEgpRuleFromAsThe Autonomous System of the route in the route
table. Local indicates that the route was not an
external OSPF route. The value 65535 is a wild
card matching any AS number, and the value 65534 is
for routes within the local AS.ro INTEGER ( 0..65535 ) .1.3.6.1.4.1.33.10.16.2.2.1.3 |
expOspfToEgpRuleActionControl whether the route is advertised or not.rw Enumeration .1.3.6.1.4.1.33.10.16.2.2.1.4 |
expOspfToEgpRuleMetricActionHow to apply the expOspfToEgpRuleMetric field to
the metric in the route table entry before the route
is advertised.rw Enumeration .1.3.6.1.4.1.33.10.16.2.2.1.5 |
expOspfToEgpRuleMetricMetric value to be applied to the metric in the
route table entry before the route is advertised.rw INTEGER .1.3.6.1.4.1.33.10.16.2.2.1.6 |
expOspfToEgpRuleStatusThe status of the rule. Set to 'invalid' to remove
the rule. If the all wild card rule is removed, it
is automatically readded with default values.rw Enumeration .1.3.6.1.4.1.33.10.16.2.2.1.7 |
expStaticToEgpRuleTableThe Static to EGP export table. SEQUENCE OF ExpStaticToEgpRuleEntry .1.3.6.1.4.1.33.10.16.2.3 |
expStaticToEgpRuleEntryAn Static to EGP export rule. Each rule is keyed
by the Autonomous System of the EGP neighbor and
the IP network of the Static route in the routing
table. The neighbor (to) AS can be set to a wild
card as can the IP network. The route is either
accepted to be advertised to the neighbor or
discarded from being advertised, and its metric is
applied according to the rule. The best match is
as follows:
To As IP Network Rank
exact exact 1st
exact wild card 2nd
wild card exact 3rd
wild card wild card 4th ExpStaticToEgpRuleEntry .1.3.6.1.4.1.33.10.16.2.3.1 |
expStaticToEgpRuleToAsThe Autonomous System of the neighbor. The value
65535 is a wild card matching any AS number.ro INTEGER ( 0..65535 ) .1.3.6.1.4.1.33.10.16.2.3.1.1 |
expStaticToEgpRuleNetworkThe IP network of the route in the route table.
The value 255.255.255.255 is a wild card matching
any network.ro IpAddress .1.3.6.1.4.1.33.10.16.2.3.1.2 |
expStaticToEgpRuleActionControl whether the route is advertised or not.rw Enumeration .1.3.6.1.4.1.33.10.16.2.3.1.3 |
expStaticToEgpRuleMetricActionHow to apply the expStaticToEgpRuleMetric field to
the metric in the route table entry before the route
is advertised.rw Enumeration .1.3.6.1.4.1.33.10.16.2.3.1.4 |
expStaticToEgpRuleMetricMetric value to be applied to the metric in the
route table entry before the route is advertised.rw INTEGER .1.3.6.1.4.1.33.10.16.2.3.1.5 |
expStaticToEgpRuleStatusThe status of the rule. Set to 'invalid' to remove
the rule. If the all wild card rule is removed, it
is automatically readded with default values.rw Enumeration .1.3.6.1.4.1.33.10.16.2.3.1.6 |
expEgpToOspfRuleTableThe EGP to OSPF export table. SEQUENCE OF ExpEgpToOspfRuleEntry .1.3.6.1.4.1.33.10.16.2.4 |
expEgpToOspfRuleEntryAn EGP to OSPF export rule. Each rule is keyed by
the IP network of the EGP route in the routing
table, and the Autonomous System from which the
route was learned. The Ip network can be set to a
wild card as can the (from) AS. The route is either
accepted to be advertised to the neighbor or
discarded from being advertised, and its metric is
applied according to the rule. The best match is as
follows:
IP Network From AS Rank
exact exact 1st
exact wild card 2nd
wild card exact 3rd
wild card wild card 4th ExpEgpToOspfRuleEntry .1.3.6.1.4.1.33.10.16.2.4.1 |
expEgpToOspfRuleNetworkThe IP network of the route in the route table.
The value 255.255.255.255 is a wild card matching
any network.ro IpAddress .1.3.6.1.4.1.33.10.16.2.4.1.1 |
expEgpToOspfRuleFromAsThe Autonomous System of the route in the route
table. The value 65535 is a wild card matching any
AS number.ro INTEGER ( 0..65535 ) .1.3.6.1.4.1.33.10.16.2.4.1.2 |
expEgpToOspfRuleActionControl whether the route is advertised or not.rw Enumeration .1.3.6.1.4.1.33.10.16.2.4.1.3 |
expEgpToOspfRuleStatusThe status of the rule. Set to 'invalid' to remove
the rule. If the all wild card rule is removed, it
is automatically readded with default values.rw Enumeration .1.3.6.1.4.1.33.10.16.2.4.1.4 |
expRipToEgpRuleTableThe Rip to EGP export table. SEQUENCE OF ExpRipToEgpRuleEntry .1.3.6.1.4.1.33.10.16.2.5 |
expRipToEgpRuleEntryAn Rip to EGP export rule. Each rule is keyed by
the Autonomous System of the EGP neighbor and the IP
network of the Rip route in the routing table. The
neighbor (to) AS can be set to a wild card as can
the IP network. The route is either accepted to be
advertised to the neighbor or discarded from being
advertised, and its metric is applied according to
the rule. The best match is as follows:
To As IP Network Best Match Rank
exact exact 1st
exact wild card 2nd
wild card exact 3rd
wild card wild card 4th ExpRipToEgpRuleEntry .1.3.6.1.4.1.33.10.16.2.5.1 |
expRipToEgpRuleToAsThe Autonomous System of the neighbor. The value
65535 is a wild card matching any AS number.ro INTEGER ( 0..65535 ) .1.3.6.1.4.1.33.10.16.2.5.1.1 |
expRipToEgpRuleNetworkThe IP network of the route in the route table.
The value 255.255.255.255 is a wild card matching
any network.ro IpAddress .1.3.6.1.4.1.33.10.16.2.5.1.2 |
expRipToEgpRuleActionControl whether the route is advertised or not.rw Enumeration .1.3.6.1.4.1.33.10.16.2.5.1.3 |
expRipToEgpRuleMetricActionHow to apply the expRipToEgpRuleMetric field to the
metric in the route table entry before the route is
advertised.rw Enumeration .1.3.6.1.4.1.33.10.16.2.5.1.4 |
expRipToEgpRuleMetricMetric value to be applied to the metric in the
route table entry before the route is advertised.rw INTEGER .1.3.6.1.4.1.33.10.16.2.5.1.5 |
expRipToEgpRuleStatusThe status of the rule. Set to 'invalid' to remove
the rule. If the all wild card rule is removed, it
is automatically readded with default values.rw Enumeration .1.3.6.1.4.1.33.10.16.2.5.1.6 |
expRipToOspfRuleTableThe RIP to OSPF export table. SEQUENCE OF ExpRipToOspfRuleEntry .1.3.6.1.4.1.33.10.16.2.6 |
expRipToOspfRuleEntryA RIP to OSPF export rule. Each rule is keyed by
the IP network of the RIP route in the routing
table. The IP network can be set to a wild card.
The route is either accepted to be advertised to the
neighbor or discarded from being advertised, and its
metric is applied according to the rule. The best
match is as follows:
IP Network Best Match Rank
exact 1st
wild card 2nd ExpRipToOspfRuleEntry .1.3.6.1.4.1.33.10.16.2.6.1 |
expRipToOspfRuleNetworkThe IP network of the route in the route table.
The value 255.255.255.255 is a wild card matching
any network.ro IpAddress .1.3.6.1.4.1.33.10.16.2.6.1.1 |
expRipToOspfRuleActionControl whether the route is advertised or not.rw Enumeration .1.3.6.1.4.1.33.10.16.2.6.1.2 |
expRipToOspfRuleStatusThe status of the rule. Set to 'invalid' to remove
the rule. If the all wild card rule is removed, it
is automatically readded with default values.rw Enumeration .1.3.6.1.4.1.33.10.16.2.6.1.3 |
expEgpToRipRuleTableThe EGP to RIP export table. SEQUENCE OF ExpEgpToRipRuleEntry .1.3.6.1.4.1.33.10.16.2.7 |
expEgpToRipRuleEntryAn EGP to RIP export rule. Each rule is keyed by
the Autonomous System of the EGP neighbor, the IP
network of the EGP route in the routing table, and
the Autonomous System from which the route was
learned. The IP network can be set to a wild card
as can the the from AS. The route is either
accepted to be advertised to the neighbor or
discarded from being advertised, and its metric is
applied according to the rule. The best match is as
follows:
IP Network From AS Best Match Rank
exact exact 1st
exact wild card 2nd
wild card exact 3rd
wild card wild card 4th ExpEgpToRipRuleEntry .1.3.6.1.4.1.33.10.16.2.7.1 |
expEgpToRipRuleToIfThe IP address of the RIP interface to which the
rule applies.ro IpAddress .1.3.6.1.4.1.33.10.16.2.7.1.1 |
expEgpToRipRuleNetworkThe IP network of the route in the route table.
The value 255.255.255.255 is a wild card matching
any network.ro IpAddress .1.3.6.1.4.1.33.10.16.2.7.1.2 |
expEgpToRipRuleFromAsThe Autonomous System of the route in the route
table. The value 65535 is a wild card matching any
AS number.ro INTEGER ( 0..65535 ) .1.3.6.1.4.1.33.10.16.2.7.1.3 |
expEgpToRipRuleActionControl whether the route is advertised or not.rw Enumeration .1.3.6.1.4.1.33.10.16.2.7.1.4 |
expEgpToRipRuleMetricActionHow to apply the expEgpToRipRuleMetric field to the
metric in the route table entry before the route is
advertised.rw Enumeration .1.3.6.1.4.1.33.10.16.2.7.1.5 |
expEgpToRipRuleMetricMetric value to be applied to the metric in the
route table entry before the route is advertised.rw INTEGER .1.3.6.1.4.1.33.10.16.2.7.1.6 |
expEgpToRipRuleStatusThe status of the rule. Set to 'invalid' to remove
the rule. If the all wild card rule is removed, it
is automatically readded with default values.rw Enumeration .1.3.6.1.4.1.33.10.16.2.7.1.7 |
expOspfToRipRuleTableThe OSPF to RIP export table. SEQUENCE OF ExpOspfToRipRuleEntry .1.3.6.1.4.1.33.10.16.2.8 |
expOspfToRipRuleEntryAn Ospf to RIP export rule. Each rule is keyed by
the Autonomous System of the Ospf neighbor, the IP
network of the Ospf route in the routing table, and
the Autonomous System from which the route was
learned. The IP network can be set to a wild card
as can the the from AS. The route is either
accepted to be advertised to the neighbor or
discarded from being advertised, and its metric is
applied according to the rule. The best match is as
follows:
IP Network From AS Best Match Rank
exact exact 1st
exact wild card 2nd
wild card exact 3rd
wild card wild card 4th ExpOspfToRipRuleEntry .1.3.6.1.4.1.33.10.16.2.8.1 |
expOspfToRipRuleToIfThe IP address of the RIP interface to which the
rule applies.ro IpAddress .1.3.6.1.4.1.33.10.16.2.8.1.1 |
expOspfToRipRuleNetworkThe IP network of the route in the route table.
The value 255.255.255.255 is a wild card matching
any network.ro IpAddress .1.3.6.1.4.1.33.10.16.2.8.1.2 |
expOspfToRipRuleFromAsThe Autonomous System of the route in the route
table. The value 65535 is a wild card matching any
AS number, and the value 65534 is for routes within
the local AS.ro INTEGER ( 0..65535 ) .1.3.6.1.4.1.33.10.16.2.8.1.3 |
expOspfToRipRuleActionControl whether the route is advertised or not.rw Enumeration .1.3.6.1.4.1.33.10.16.2.8.1.4 |
expOspfToRipRuleMetricActionHow to apply the expOspfToRipRuleMetric field to
the metric in the route table entry before the route
is advertised.rw Enumeration .1.3.6.1.4.1.33.10.16.2.8.1.5 |
expOspfToRipRuleMetricMetric value to be applied to the metric in the
route table entry before the route is advertised.rw INTEGER .1.3.6.1.4.1.33.10.16.2.8.1.6 |
expOspfToRipRuleStatusThe status of the rule. Set to 'invalid' to remove
the rule. If the all wild card rule is removed, it
is automatically readded with default values. The
same is true for the all wild cards where the AS is
set to localrw Enumeration .1.3.6.1.4.1.33.10.16.2.8.1.7 |
expRipToRipRuleTableThe Rip to Rip export table. SEQUENCE OF ExpRipToRipRuleEntry .1.3.6.1.4.1.33.10.16.2.9 |
expRipToRipRuleEntryAn Rip to Rip export rule. Each rule is keyed by
the IP network of the Rip route in the routing
table. The neighbor IP network can be set to a wild
card. The route is either accepted to be advertised
to the neighbor or discarded from being advertised,
and its metric is applied according to the rule.
The best match is as follows:
IP Network Best Match Rank
exact 1st
wild card 2nd ExpRipToRipRuleEntry .1.3.6.1.4.1.33.10.16.2.9.1 |
expRipToRipRuleToIfThe IP address of the RIP interface to which the
rule applies.ro IpAddress .1.3.6.1.4.1.33.10.16.2.9.1.1 |
expRipToRipRuleNetworkThe IP network of the route in the route table.
The value 255.255.255.255 is a wild card matching
any network.ro IpAddress .1.3.6.1.4.1.33.10.16.2.9.1.2 |
expRipToRipRuleActionControl whether the route is advertised or not.rw Enumeration .1.3.6.1.4.1.33.10.16.2.9.1.3 |
expRipToRipRuleMetricActionHow to apply the expRipToRipRuleMetric field to the
metric in the route table entry before the route is
advertised.rw Enumeration .1.3.6.1.4.1.33.10.16.2.9.1.4 |
expRipToRipRuleMetricMetric value to be applied to the metric in the
route table entry before the route is advertised.rw INTEGER .1.3.6.1.4.1.33.10.16.2.9.1.5 |
expRipToRipRuleStatusThe status of the rule. Set to 'invalid' to remove
the rule. If the all wild card rule is removed, it
is automatically readded with default values.rw Enumeration .1.3.6.1.4.1.33.10.16.2.9.1.6 |
expStaticToRipRuleTableThe Static to Rip export table. SEQUENCE OF ExpStaticToRipRuleEntry .1.3.6.1.4.1.33.10.16.2.10 |
expStaticToRipRuleEntryAn Static to Rip export rule. Each rule is keyed
by the IP network of the Static route in the routing
table. The neighbor IP network can be set to a wild
card. The route is either accepted to be advertised
to the neighbor or discarded from being advertised,
and its metric is applied according to the rule.
The best match is as follows:
IP Network Best Match Rank
exact 1st
wild card 2nd ExpStaticToRipRuleEntry .1.3.6.1.4.1.33.10.16.2.10.1 |
expStaticToRipRuleToIfThe IP address of the RIP interface to which the
rule applies.ro IpAddress .1.3.6.1.4.1.33.10.16.2.10.1.1 |
expStaticToRipRuleNetworkThe IP network of the route in the route table.
The value 255.255.255.255 is a wild card matching
any network.ro IpAddress .1.3.6.1.4.1.33.10.16.2.10.1.2 |
expStaticToRipRuleActionControl whether the route is advertised or not.rw Enumeration .1.3.6.1.4.1.33.10.16.2.10.1.3 |
expStaticToRipRuleMetricActionHow to apply the expStaticToRipRuleMetric field to
the metric in the route table entry before the route
is advertised.rw Enumeration .1.3.6.1.4.1.33.10.16.2.10.1.4 |
expStaticToRipRuleMetricMetric value to be applied to the metric in the
route table entry before the route is advertised.rw INTEGER .1.3.6.1.4.1.33.10.16.2.10.1.5 |
expStaticToRipRuleStatusThe status of the rule. Set to 'invalid' to remove
the rule. If the all wild card rule is removed, it
is automatically readded with default values.rw Enumeration .1.3.6.1.4.1.33.10.16.2.10.1.6 |
expIsisToEgpRuleTableThe Isis to EGP export table. SEQUENCE OF ExpIsisToEgpRuleEntry .1.3.6.1.4.1.33.10.16.2.11 |
expIsisToEgpRuleEntryAn Isis to EGP export rule. Each rule is keyed by the Autonomous
System of the EGP neighbor and the IP network of the Isis route in the
routing table. The neighbor (to) AS can be set to a wild card as can
the IP network. The route is either accepted to be advertised to the
neighbor or discarded from being advertised, and its metric is applied
according to the rule. The best match is as follows:
To As IP Network Best Match Rank
exact exact 1st
exact wild card 2nd
wild card exact 3rd
wild card wild card 4th
. ExpIsisToEgpRuleEntry .1.3.6.1.4.1.33.10.16.2.11.1 |
expIsisToEgpRuleToAsThe Autonomous System of the neighbor. The value 65535 is
a wild card matching any AS number.ro INTEGER ( 0..65535 ) .1.3.6.1.4.1.33.10.16.2.11.1.1 |
expIsisToEgpRuleNetworkThe IP network of the route in the route table. The value
255.255.255.255 is a wild card matching any network.ro IpAddress .1.3.6.1.4.1.33.10.16.2.11.1.2 |
expIsisToEgpRuleActionControl whether the route is advertised or not.rw Enumeration .1.3.6.1.4.1.33.10.16.2.11.1.3 |
expIsisToEgpRuleMetricActionHow to apply the expIsisToEgpRuleMetric field to the metric in the route
table entry before the route is advertised.rw Enumeration .1.3.6.1.4.1.33.10.16.2.11.1.4 |
expIsisToEgpRuleMetricMetric value to be applied to the metric in the route table entry
before the route is advertised.rw INTEGER .1.3.6.1.4.1.33.10.16.2.11.1.5 |
expIsisToEgpRuleStatusThe status of the rule. Set to 'invalid' to remove
the rule. If the all wild card rule is removed, it is
automatically readded with default values.rw Enumeration .1.3.6.1.4.1.33.10.16.2.11.1.6 |
expIsisToOspfRuleTableThe Isis to Ospf export table. SEQUENCE OF ExpIsisToOspfRuleEntry .1.3.6.1.4.1.33.10.16.2.12 |
expIsisToOspfRuleEntryAn Isis to Ospf export rule. Each rule is keyed by the IP network of
the Isis route in the routing table. The IP network can be set to a
wild card. The route is either accepted to be advertised to the
neighbor or discarded from being advertised, and its metric is applied
according to the rule. The best match is as follows:
IP Network Best Match Rank
exact 1st
wild card 2nd
. ExpIsisToOspfRuleEntry .1.3.6.1.4.1.33.10.16.2.12.1 |
expIsisToOspfRuleNetworkThe IP network of the route in the route table. The value
255.255.255.255 is a wild card matching any network.ro IpAddress .1.3.6.1.4.1.33.10.16.2.12.1.1 |
expIsisToOspfRuleActionControl whether the route is advertised or not.rw Enumeration .1.3.6.1.4.1.33.10.16.2.12.1.2 |
expIsisToOspfRuleStatusThe status of the rule. Set to 'invalid' to remove
the rule. If the all wild card rule is removed, it is
automatically readded with default values.rw Enumeration .1.3.6.1.4.1.33.10.16.2.12.1.3 |
expIsisToRipRuleTableThe Isis to Rip export table. SEQUENCE OF ExpIsisToRipRuleEntry .1.3.6.1.4.1.33.10.16.2.13 |
expIsisToRipRuleEntryAn Isis to Rip export rule. Each rule is keyed by the IP
network of the Isis route in the routing table. The IP
network can be set to a wild card. The route is either
accepted to be advertised to the neighbor or discarded
from being advertised, and its metric is applied
according to the rule. The best match is as follows:
IP Network Best Match Rank
exact 1st
wild card 2nd
. ExpIsisToRipRuleEntry .1.3.6.1.4.1.33.10.16.2.13.1 |
expIsisToRipRuleToIfThe IP address of the RIP interface to which the
rule applies.ro IpAddress .1.3.6.1.4.1.33.10.16.2.13.1.1 |
expIsisToRipRuleNetworkThe IP network of the route in the route table. The value
255.255.255.255 is a wild card matching any network.ro IpAddress .1.3.6.1.4.1.33.10.16.2.13.1.2 |
expIsisToRipRuleActionControl whether the route is advertised or not.rw Enumeration .1.3.6.1.4.1.33.10.16.2.13.1.3 |
expIsisToRipRuleMetricActionHow to apply the expIsisToRipRuleMetric field to the metric in the route
table entry before the route is advertised.rw Enumeration .1.3.6.1.4.1.33.10.16.2.13.1.4 |
expIsisToRipRuleMetricMetric value to be applied to the metric in the route table entry
before the route is advertised.rw INTEGER .1.3.6.1.4.1.33.10.16.2.13.1.5 |
expIsisToRipRuleStatusThe status of the rule. Set to 'invalid' to remove
the rule. If the all wild card rule is removed, it is
automatically readded with default values.rw Enumeration .1.3.6.1.4.1.33.10.16.2.13.1.6 |
expEgpToIsisRuleTableThe EGP to Isis export table. SEQUENCE OF ExpEgpToIsisRuleEntry .1.3.6.1.4.1.33.10.16.2.14 |
expEgpToIsisRuleEntryAn EGP to Isis export rule. Each rule is keyed by the Autonomous
System of the EGP neighbor, the IP network of the EGP route in the
routing table, and the Autonomous System from which the route was
learned. The IP network can be set to a wild card as can the
from AS. The route is either accepted to be advertised to the
neighbor or discarded from being advertised, and its metric is applied
according to the rule. The best match is as follows:
IP Network From AS Best Match Rank
exact exact 1st
exact wild card 2nd
wild card exact 3rd
wild card wild card 4th
. ExpEgpToIsisRuleEntry .1.3.6.1.4.1.33.10.16.2.14.1 |
expEgpToIsisRuleNetworkThe IP network of the route in the route table. The value
255.255.255.255 is a wild card matching any network.ro IpAddress .1.3.6.1.4.1.33.10.16.2.14.1.1 |
expEgpToIsisRuleFromAsThe Autonomous System of the route in the route table. The value
65535 is a wild card matching any AS number.ro INTEGER ( 0..65535 ) .1.3.6.1.4.1.33.10.16.2.14.1.2 |
expEgpToIsisRuleActionControl whether the route is advertised or not.rw Enumeration .1.3.6.1.4.1.33.10.16.2.14.1.3 |
expEgpToIsisRuleMetricTypeWhether to advertise the metric as Internal or External.rw Enumeration .1.3.6.1.4.1.33.10.16.2.14.1.4 |
expEgpToIsisRuleDefaultMetricActionHow to apply the expEgpToIsisDefaultRuleMetric field to the metric in the route
table entry before the route is advertised.rw Enumeration .1.3.6.1.4.1.33.10.16.2.14.1.5 |
expEgpToIsisRuleDefaultMetricDefault metric value to be applied to the metric in the route table entry
before the route is advertised.rw INTEGER .1.3.6.1.4.1.33.10.16.2.14.1.6 |
expEgpToIsisRuleDelayMetricActionHow to apply the expEgpToIsisDelayRuleMetric field to the metric in the
route table entry before the route is advertised.rw Enumeration .1.3.6.1.4.1.33.10.16.2.14.1.7 |
expEgpToIsisRuleDelayMetricDelay metric value to be applied to the metric in the route table entry
before the route is advertised.rw INTEGER .1.3.6.1.4.1.33.10.16.2.14.1.8 |
expEgpToIsisRuleErrorMetricActionHow to apply the expEgpToIsisErrorRuleMetric field to the metric in the route
table entry before the route is advertised.rw Enumeration .1.3.6.1.4.1.33.10.16.2.14.1.9 |
expEgpToIsisRuleErrorMetricError metric value to be applied to the metric in the route table entry
before the route is advertised.rw INTEGER .1.3.6.1.4.1.33.10.16.2.14.1.10 |
expEgpToIsisRuleExpenseMetricActionHow to apply the expEgpToIsisExpenseRuleMetric field to the metric in the route
table entry before the route is advertised.rw Enumeration .1.3.6.1.4.1.33.10.16.2.14.1.11 |
expEgpToIsisRuleExpenseMetricExpense metric value to be applied to the metric in the route table entry
before the route is advertised.rw INTEGER .1.3.6.1.4.1.33.10.16.2.14.1.12 |
expEgpToIsisRuleStatusThe status of the rule. Set to 'invalid' to remove
the rule. If the all wild card rule is removed, it is
automatically readded with default values.rw Enumeration .1.3.6.1.4.1.33.10.16.2.14.1.13 |
expOspfToIsisRuleTableThe Ospf to Isis export table. SEQUENCE OF ExpOspfToIsisRuleEntry .1.3.6.1.4.1.33.10.16.2.15 |
expOspfToIsisRuleEntryAn Ospf to Isis export rule. Each rule is keyed by the
Autonomous System of the Ospf neighbor, the IP network of
the Ospf route in the routing table, and the Autonomous
System from which the route was learned. The IP network
can be set to a wild card as can the the from AS. The
route is either accepted to be advertised to the neighbor
or discarded from being advertised, and its metric is
applied according to the rule. The best match is as
follows:
IP Network From AS Best Match Rank
exact exact 1st
exact wild card 2nd
wild card exact 3rd
wild card wild card 4th
. ExpOspfToIsisRuleEntry .1.3.6.1.4.1.33.10.16.2.15.1 |
expOspfToIsisRuleNetworkThe IP network of the route in the route table. The value
255.255.255.255 is a wild card matching any network.ro IpAddress .1.3.6.1.4.1.33.10.16.2.15.1.1 |
expOspfToIsisRuleFromAsThe Autonomous System of the route in the route table.
The value 65535 is a wild card matching any AS number,
and the value 65534 is for routes within the local AS.ro INTEGER ( 0..65535 ) .1.3.6.1.4.1.33.10.16.2.15.1.2 |
expOspfToIsisRuleActionControl whether the route is advertised or not.rw Enumeration .1.3.6.1.4.1.33.10.16.2.15.1.3 |
expOspfToIsisRuleMetricTypeWhether to advertise the metric as Internal or External.rw Enumeration .1.3.6.1.4.1.33.10.16.2.15.1.4 |
expOspfToIsisRuleDefaultMetricActionHow to apply the expOspfToIsisDefaultRuleMetric field to
the metric in the route table entry before the route is
advertised.rw Enumeration .1.3.6.1.4.1.33.10.16.2.15.1.5 |
expOspfToIsisRuleDefaultMetricDefault metric value to be applied to the metric in the route table entry
before the route is advertised.rw INTEGER .1.3.6.1.4.1.33.10.16.2.15.1.6 |
expOspfToIsisRuleDelayMetricActionHow to apply the expOspfToIsisDelayRuleMetric field to the metric in the route
table entry before the route is advertised.rw Enumeration .1.3.6.1.4.1.33.10.16.2.15.1.7 |
expOspfToIsisRuleDelayMetricDelay metric value to be applied to the metric in the route table entry
before the route is advertised.rw INTEGER .1.3.6.1.4.1.33.10.16.2.15.1.8 |
expOspfToIsisRuleErrorMetricActionHow to apply the expOspfToIsisErrorRuleMetric field to the metric in the route
table entry before the route is advertised.rw Enumeration .1.3.6.1.4.1.33.10.16.2.15.1.9 |
expOspfToIsisRuleErrorMetricError metric value to be applied to the metric in the route table entry
before the route is advertised.rw INTEGER .1.3.6.1.4.1.33.10.16.2.15.1.10 |
expOspfToIsisRuleExpenseMetricActionHow to apply the expOspfToIsisExpenseRuleMetric field to the metric in the route
table entry before the route is advertised.rw Enumeration .1.3.6.1.4.1.33.10.16.2.15.1.11 |
expOspfToIsisRuleExpenseMetricExpense metric value to be applied to the metric in the route table entry
before the route is advertised.rw INTEGER .1.3.6.1.4.1.33.10.16.2.15.1.12 |
expOspfToIsisRuleStatusThe status of the rule. Set to 'invalid' to remove
the rule. If the all wild card rule is removed, it is
automatically readded with default values. The same is
true for the all wild cards where the AS is set to localrw Enumeration .1.3.6.1.4.1.33.10.16.2.15.1.13 |
expRipToIsisRuleTableThe Isis to Isis export table. SEQUENCE OF ExpRipToIsisRuleEntry .1.3.6.1.4.1.33.10.16.2.16 |
expRipToIsisRuleEntryAn Isis to Isis export rule. Each rule is keyed by the
IP network of the Isis route in the routing table. The
neighbor IP network can be set to a wild card. The route
is either accepted to be advertised to the neighbor or
discarded from being advertised, and its metric is applied
according to the rule. The best match is as follows:
IP Network Best Match Rank
exact 1st
wild card 2nd
. ExpRipToIsisRuleEntry .1.3.6.1.4.1.33.10.16.2.16.1 |
expRipToIsisRuleNetworkThe IP network of the route in the route table. The value
255.255.255.255 is a wild card matching any network.ro IpAddress .1.3.6.1.4.1.33.10.16.2.16.1.1 |
expRipToIsisRuleActionControl whether the route is advertised or not.rw Enumeration .1.3.6.1.4.1.33.10.16.2.16.1.2 |
expRipToIsisRuleMetricTypeWhether to advertise the metric as Internal or External.rw Enumeration .1.3.6.1.4.1.33.10.16.2.16.1.3 |
expRipToIsisRuleDefaultMetricActionHow to apply the expRipToIsisDefaultRuleMetric field to the metric in the route
table entry before the route is advertised.rw Enumeration .1.3.6.1.4.1.33.10.16.2.16.1.4 |
expRipToIsisRuleDefaultMetricDefault metric value to be applied to the metric in the route table entry
before the route is advertised.rw INTEGER .1.3.6.1.4.1.33.10.16.2.16.1.5 |
expRipToIsisRuleDelayMetricActionHow to apply the expRipToIsisDelayRuleMetric field to the metric in the route
table entry before the route is advertised.rw Enumeration .1.3.6.1.4.1.33.10.16.2.16.1.6 |
expRipToIsisRuleDelayMetricDelay metric value to be applied to the metric in the route table entry
before the route is advertised.rw INTEGER .1.3.6.1.4.1.33.10.16.2.16.1.7 |
expRipToIsisRuleErrorMetricActionHow to apply the expRipToIsisErrorRuleMetric field to the metric in the route
table entry before the route is advertised.rw Enumeration .1.3.6.1.4.1.33.10.16.2.16.1.8 |
expRipToIsisRuleErrorMetricError metric value to be applied to the metric in the
route table entry before the route is advertised.rw INTEGER .1.3.6.1.4.1.33.10.16.2.16.1.9 |
expRipToIsisRuleExpenseMetricActionHow to apply the expRipToIsisExpenseRuleMetric field to
the metric in the route table entry before the route is
advertised.rw Enumeration .1.3.6.1.4.1.33.10.16.2.16.1.10 |
expRipToIsisRuleExpenseMetricExpense metric value to be applied to the metric in the
route table entry before the route is advertised.rw INTEGER .1.3.6.1.4.1.33.10.16.2.16.1.11 |
expRipToIsisRuleStatusThe status of the rule. Set to 'invalid' to remove
the rule. If the all wild card rule is removed, it is
automatically readded with default values.rw Enumeration .1.3.6.1.4.1.33.10.16.2.16.1.12 |
expStaticToIsisRuleTableThe Static to Isis export table. SEQUENCE OF ExpStaticToIsisRuleEntry .1.3.6.1.4.1.33.10.16.2.17 |
expStaticToIsisRuleEntryAn Static to Isis export rule. Each rule is keyed by the
IP network of the Static route in the routing table. The
neighbor IP network can be set to a wild card. The route
is either accepted to be advertised to the neighbor or
discarded from being advertised, and its metric is applied
according to the rule. The best match is as follows:
IP Network Best Match Rank
exact 1st
wild card 2nd
. ExpStaticToIsisRuleEntry .1.3.6.1.4.1.33.10.16.2.17.1 |
expStaticToIsisRuleNetworkThe IP network of the route in the route table. The value
255.255.255.255 is a wild card matching any network.ro IpAddress .1.3.6.1.4.1.33.10.16.2.17.1.1 |
expStaticToIsisRuleActionControl whether the route is advertised or not.rw Enumeration .1.3.6.1.4.1.33.10.16.2.17.1.2 |
expStaticToIsisRuleMetricTypeWhether to advertise the metric as Internal or External.rw Enumeration .1.3.6.1.4.1.33.10.16.2.17.1.3 |
expStaticToIsisRuleDefaultMetricActionHow to apply the expStaticToIsisDefaultRuleMetric field
to the metric in the route table entry before the route
is advertised.rw Enumeration .1.3.6.1.4.1.33.10.16.2.17.1.4 |
expStaticToIsisRuleDefaultMetricDefault metric value to be applied to the metric in the
route table entry before the route is advertised.rw INTEGER .1.3.6.1.4.1.33.10.16.2.17.1.5 |
expStaticToIsisRuleDelayMetricActionHow to apply the expStaticToIsisDelayRuleMetric field
to the metric in the route table entry before the route
is advertised.rw Enumeration .1.3.6.1.4.1.33.10.16.2.17.1.6 |
expStaticToIsisRuleDelayMetricDelay metric value to be applied to the metric in the
route table entry before the route is advertised.rw INTEGER .1.3.6.1.4.1.33.10.16.2.17.1.7 |
expStaticToIsisRuleErrorMetricActionHow to apply the expStaticToIsisErrorRuleMetric field
to the metric in the route table entry before the route
is advertised.rw Enumeration .1.3.6.1.4.1.33.10.16.2.17.1.8 |
expStaticToIsisRuleErrorMetricError metric value to be applied to the metric in the
route table entry before the route is advertised.rw INTEGER .1.3.6.1.4.1.33.10.16.2.17.1.9 |
expStaticToIsisRuleExpenseMetricActionHow to apply the expStaticToIsisExpenseRuleMetric field
to the metric in the route table entry before the route
is advertised.rw Enumeration .1.3.6.1.4.1.33.10.16.2.17.1.10 |
expStaticToIsisRuleExpenseMetricExpense metric value to be applied to the metric in the
route table entry before the route is advertised.rw INTEGER .1.3.6.1.4.1.33.10.16.2.17.1.11 |
expStaticToIsisRuleStatusThe status of the rule. Set to 'invalid' to remove
the rule. If the all wild card rule is removed, it is
automatically readded with default values.rw Enumeration .1.3.6.1.4.1.33.10.16.2.17.1.12 |
xFilter OBJECT IDENTIFIER .1.3.6.1.4.1.33.10.16.3 |
ipIfFilterTableTable of filter entries.deprecated SEQUENCE OF IpIfFilterEntry .1.3.6.1.4.1.33.10.16.3.1 |
ipIfFilterEntryA particular entry.deprecated IpIfFilterEntry .1.3.6.1.4.1.33.10.16.3.1.1 |
ipIfFilterIndexThe interface index with which this entry is
associated. This value is the same as IfIndex.rodeprecated INTEGER .1.3.6.1.4.1.33.10.16.3.1.1.1 |
ipIfFilterDstAddrThe destination IP address to use in the filter
match.rodeprecated IpAddress .1.3.6.1.4.1.33.10.16.3.1.1.2 |
ipIfFilterDstMaskThe destination IP mask to use in the filter
match.rodeprecated IpAddress .1.3.6.1.4.1.33.10.16.3.1.1.3 |
ipIfFilterSrcAddrThe source IP address to use in the filter match.rodeprecated IpAddress .1.3.6.1.4.1.33.10.16.3.1.1.4 |
ipIfFilterSrcMaskThe source IP mask to use in the filter match.rodeprecated IpAddress .1.3.6.1.4.1.33.10.16.3.1.1.5 |
ipIfFilterProtocolThe protocol to use in the filter match. The value
256 indicates any protocol.rodeprecated INTEGER ( 0..256 ) .1.3.6.1.4.1.33.10.16.3.1.1.6 |
ipIfFilterDstPortThe destination port to use in the filter match.
This field only applies to TCP and UDP protocol
packets. The value 65536 indicates any destination
port.rodeprecated INTEGER ( 0..65536 ) .1.3.6.1.4.1.33.10.16.3.1.1.7 |
ipIfFilterSrcPortThe source port to use in the filter match. This
field only applies to TCP and UDP protocol packets.
The value 65536 indicates any source port.rodeprecated INTEGER ( 0..65536 ) .1.3.6.1.4.1.33.10.16.3.1.1.8 |
ipIfFilterActionControl whether the packet for which this filter is
the best match should be forwarded or discarded.rwdeprecated Enumeration .1.3.6.1.4.1.33.10.16.3.1.1.9 |
ipIfFilterStatusThe status of the filter entry. Set to 'invalid'
to remove the entry.rwdeprecated Enumeration .1.3.6.1.4.1.33.10.16.3.1.1.10 |
ipFilterStateThe indication of whether this system does IP
filtering.rw Enumeration .1.3.6.1.4.1.33.10.16.3.2 |
ipIfFilter2TableTable of filter entries. SEQUENCE OF IpIfFilter2Entry .1.3.6.1.4.1.33.10.16.3.3 |
ipIfFilter2EntryA particular entry. IpIfFilter2Entry .1.3.6.1.4.1.33.10.16.3.3.1 |
ipIfFilter2IndexThe interface index with which this entry is
associated. This value is the same as IfIndex.ro INTEGER .1.3.6.1.4.1.33.10.16.3.3.1.1 |
ipIfFilter2DstAddrThe destination IP address to use in the filter
match.ro IpAddress .1.3.6.1.4.1.33.10.16.3.3.1.2 |
ipIfFilter2DstMaskThe destination IP mask to use in the filter
match.ro IpAddress .1.3.6.1.4.1.33.10.16.3.3.1.3 |
ipIfFilter2SrcAddrThe source IP address to use in the filter match.ro IpAddress .1.3.6.1.4.1.33.10.16.3.3.1.4 |
ipIfFilter2SrcMaskThe source IP mask to use in the filter match.ro IpAddress .1.3.6.1.4.1.33.10.16.3.3.1.5 |
ipIfFilter2ProtocolThe protocol to use in the filter match. The value
256 indicates any protocol.ro INTEGER ( 0..256 ) .1.3.6.1.4.1.33.10.16.3.3.1.6 |
ipIfFilter2DstPortStartThe starting destination port in a range of
destination ports to use in the filter match.
This field only applies to TCP and UDP protocol
packets.ro INTEGER ( 0..65535 ) .1.3.6.1.4.1.33.10.16.3.3.1.7 |
ipIfFilter2SrcPortStartThe starting source port in a range of
source ports to use in the filter match.
This field only applies to TCP and UDP protocol
packets.ro INTEGER ( 0..65535 ) .1.3.6.1.4.1.33.10.16.3.3.1.8 |
ipIfFilter2ActionControl whether the packet for which this filter is
the best match should be forwarded or discarded.rw Enumeration .1.3.6.1.4.1.33.10.16.3.3.1.9 |
ipIfFilter2StatusThe status of the filter entry. Set to 'invalid'
to remove the entry.rw Enumeration .1.3.6.1.4.1.33.10.16.3.3.1.10 |
ipIfFilter2DstPortEndThe ending destination port in a range of
destination ports to use in the filter match.
This field only applies to TCP and UDP protocol
packets. This filed must also be greater or
equal to the ipIfFilter2DstPortStart field.ro INTEGER ( 0..65535 ) .1.3.6.1.4.1.33.10.16.3.3.1.11 |
ipIfFilter2SrcPortEndThe starting source port in a range of
source ports to use in the filter match.
This field only applies to TCP and UDP protocol
packets. This filed must also be greater or
equal to the ipIfFilter2SrcPortStart field.ro INTEGER ( 0..65535 ) .1.3.6.1.4.1.33.10.16.3.3.1.12 |
ipIfFilter2TcpSynThe value of the TCP SYN and ACK bit to
ues in the filter match. This field only
applies to TCP packets. On indicates
that the SYN bit is on and the ACK bit is
off. Off is any other combination.ro Enumeration .1.3.6.1.4.1.33.10.16.3.3.1.13 |
ipIfFilter2ProtocolPriorityControl the priority at which the packet for which
this filter is the best match should be placed on
the WAN output queue. None indicates that the
sending interfaces protocol priority should be used.rw Enumeration .1.3.6.1.4.1.33.10.16.3.3.1.14 |
xRip OBJECT IDENTIFIER .1.3.6.1.4.1.33.10.18 |
ripStateThe indication of whether this system participates
in RIP.rw Enumeration .1.3.6.1.4.1.33.10.18.1 |
ripStatusThe status of the RIP software.ro Enumeration .1.3.6.1.4.1.33.10.18.2 |
ripNetTableTable of RIP entries. SEQUENCE OF RipNetEntry .1.3.6.1.4.1.33.10.18.3 |
ripNetEntryA particular entry. RipNetEntry .1.3.6.1.4.1.33.10.18.3.1 |
ripNetNetThe IP Network to which this entry applies.ro IpAddress .1.3.6.1.4.1.33.10.18.3.1.1 |
ripNetStateThis value controls the RIP protocol on this
network.rw Enumeration .1.3.6.1.4.1.33.10.18.3.1.2 |
ripNetRipsInThe number of RIP packets received from routers on
this IP network.ro Counter .1.3.6.1.4.1.33.10.18.3.1.3 |
ripNetRipsOutThe number of RIP packets sent to routers on this
IP network.ro Counter .1.3.6.1.4.1.33.10.18.3.1.4 |
ripNetAlgorithmThis value controls the RIP algorithm on this
network.rw Enumeration .1.3.6.1.4.1.33.10.18.3.1.5 |
xlpd OBJECT IDENTIFIER .1.3.6.1.4.1.33.10.19 |
lpdQueueTableA list of lpd queues on the server. SEQUENCE OF LpdQueueEntry .1.3.6.1.4.1.33.10.19.1 |
lpdQueueEntryLpd parameter values plus counters for an
individual lpd queue. LpdQueueEntry .1.3.6.1.4.1.33.10.19.1.1 |
lpdQueueStatusStatus of this entry. Setting the value to
'invalid' invalidates the entry, corresponding
directly to the CLEAR/PURGE SERVER LPD QUEUE
command. Setting the value to 'valid' validates
(creates) the entry, corresonding directly to
the DEF/SET SERVER LPD QUEUE and lpd create
commands.rw Enumeration .1.3.6.1.4.1.33.10.19.1.1.1 |
lpdQueueNameName of the LPD queue, case sensitive.ro DisplayString .1.3.6.1.4.1.33.10.19.1.1.2 |
lpdQueuePortsList of ports assigned to the queue. An lpd queue
can be associated with more than 1 port. This
object corresponds to the port-list in the
DEF/SET SERVER LPD QUEUE and lpc/create commands.
The OCTET STRING contains a bitmap, with one bit for
each port, and enough octets for all the ports on
the system. Port numbers are as defined for
charPortIndex in the Character MIB [11].
Corresponding bit numbers start with 1 as the
high-order bit of the first octet.rw OCTET STRING .1.3.6.1.4.1.33.10.19.1.1.3 |
lpdQueueEnabledFlag indicates if the queue is enabled. A 'disabled'
queue will reject print requests from remote systems.
A 'enabled' queue accepts requests for printing.rw Enumeration .1.3.6.1.4.1.33.10.19.1.1.4 |
lpdQueueLfConversionFlag indicates if the queue is converting linefeeds
to linefeeds, carriagereturns. 'lfcr' does the
converion, 'lf' does not.rw Enumeration .1.3.6.1.4.1.33.10.19.1.1.5 |
lpdQueueTotalJobsThe total number of jobs on the queue. This number
should be equal to the number of active and waiting
jobs. (lpdQueueActive + lpdQueueWaiting)ro Gauge .1.3.6.1.4.1.33.10.19.1.1.6 |
lpdQueueActiveJobsThe number of active jobs on the queue. An active
job is a job that has been assigned a port is in the
process of receiving data from a remote host and
sending it out the port.ro Gauge .1.3.6.1.4.1.33.10.19.1.1.7 |
lpdQueueWaitingJobsThe number of waiting jobs on the queue. A waiting
job is a job that needs a port to send its data to.
This implies that the ports associated with this
queue are busy.ro Gauge .1.3.6.1.4.1.33.10.19.1.1.8 |
lpdQueueProcessedJobsThe total number of jobs processed by this queue
since server boot.ro Counter .1.3.6.1.4.1.33.10.19.1.1.9 |
lpdQueueFormFeedA control to determine how we will send out a formfeed
when printing a lpd job. formfeedafter: Send after job,
formfeedbefore: Send before job,
formfeednone: Send no formfeed.rw Enumeration .1.3.6.1.4.1.33.10.19.1.1.10 |
lpdQueueBypassControl for a queue to bypass a LPD port which has output
inhibited via flow control. Corresponds directly to the
value labeled 'Bypass' in the SERVER LPD QUEUE display.rw Enumeration .1.3.6.1.4.1.33.10.19.1.1.11 |
lpdJobTableA list of lpd jobs. SEQUENCE OF LpdJobEntry .1.3.6.1.4.1.33.10.19.2 |
lpdJobEntryA single lpd Job. LpdJobEntry .1.3.6.1.4.1.33.10.19.2.1 |
lpdJobStatusStatus of this entry. Setting this object to
'invalid' will remove the job from the queue.
Setting this object ot 'valid' has no effect since
the only way to create an lpd job is with the lpd
protocol.rw Enumeration .1.3.6.1.4.1.33.10.19.2.1.1 |
lpdJobNumberThe queue relative job number for this lpd job.
Job numbers are assigned as jobs are accepted onto
the queue. Job numbers are reset to 1 when they
reach a value greater than 1000 and the queue goes
empty.ro INTEGER .1.3.6.1.4.1.33.10.19.2.1.2 |
lpdJobAssignedPortThe number of the port assigned to the lpd job.ro INTEGER .1.3.6.1.4.1.33.10.19.2.1.3 |
lpdJobFileSizeThe size of the file being sent from the remote
system.ro INTEGER .1.3.6.1.4.1.33.10.19.2.1.4 |
lpdJobHostNameThe name of the host sending the job.ro DisplayString .1.3.6.1.4.1.33.10.19.2.1.5 |
lpdJobFileNameThe name of the file being sent.ro DisplayString .1.3.6.1.4.1.33.10.19.2.1.6 |
lpdJobStateThe current state of the lpd job. A typical job
transistions through the following states:
initialize->waiting->assigned->printingdata->
printingcontrol->completed.ro Enumeration .1.3.6.1.4.1.33.10.19.2.1.7 |
xSecurID OBJECT IDENTIFIER .1.3.6.1.4.1.33.10.20 |
securIDServerName0The Domain name of the first SecurID server to try
when the system verifies a SecurID PASSCODE. Corresponds
directly to SERVER SECURID SERVER0 and the
value labeled 'SecurID Server0:' in the
SERVER SECURID display.rw DisplayString .1.3.6.1.4.1.33.10.20.1 |
securIDServerName1The Domain name of the second SecurID server to try
when the system verifies a SecurID PASSCODE. Corresponds
directly to SERVER SECURID SERVER1 and the
value labeled 'SecurID Server1:' in the
SERVER SECURID display.rw DisplayString .1.3.6.1.4.1.33.10.20.2 |
securIDServerName2The Domain name of the third SecurID server to try
when the system verifies a SecurID PASSCODE. Corresponds
directly to SERVER SECURID SERVER2 and the
value labeled 'SecurID Server2:' in the
SERVER SECURID display.rw DisplayString .1.3.6.1.4.1.33.10.20.3 |
securIDServerName3The Domain name of the fourth SecurID server to try
when the system verifies a SecurID PASSCODE. Corresponds
directly to SERVER SECURID SERVER3 and the
value labeled 'SecurID Server3:' in the
SERVER SECURID display.rw DisplayString .1.3.6.1.4.1.33.10.20.4 |
securIDServerName4The Domain name of the fifth SecurID server to try
when the system verifies a SecurID PASSCODE. Corresponds
directly to SERVER SECURID SERVER4 and the
value labeled 'SecurID Server4:' in the
SERVER SECURID display.rw DisplayString .1.3.6.1.4.1.33.10.20.5 |
securIDMaxRetriesThe maximum number of times the server will
try any single SecurID server to validate a
PASSCODE. Corresponds directly to SERVER SECURID
ACMMAXRETRIES and the value labeled 'SecurID
ACMMAXRETRIES:' in the SERVER SECURID display.rw INTEGER .1.3.6.1.4.1.33.10.20.6 |
securIDBaseTimeoutThe initial timeout value to be used between prompts
for a SecurID PASSCODE.
Corresponds directly to SERVER SECURID
ACMBASETIMEOUT and the value labeled 'SecurID
ACMBASETIMEOUT:' in the SERVER SECURID display.rw INTEGER .1.3.6.1.4.1.33.10.20.7 |
securIDPortThe UDP port number to be used when communicating
with the SecurID servers. Corresponds directly to
SERVER SECURID ACM_PORT and the value labeled 'SecurID
ACM_PORT:' in the SERVER SECURID display.rw INTEGER .1.3.6.1.4.1.33.10.20.8 |
securIDQueryLimitThe maximum number of times a user will be queried
for a SecurID PASSCODE before being logged out.
Corresponds directly to
SERVER SECURID QUERY LIMIT and the value labeled 'SecurID
Query Limit:' in the SERVER SECURID display.rw INTEGER .1.3.6.1.4.1.33.10.20.9 |
securIDEncryptionModeThe type of encryption to use in SecurID validation.
Corresponds directly to the value labeled 'Encryption
Mode' in the SERVER SECURID display.rw Enumeration .1.3.6.1.4.1.33.10.20.10 |
securIDInsecureLoginsThe number of user logins on ports for which
SecurID user verification is not enabled.
Corresponds directly to the value labeled 'Logins
without SecurID:' in the SERVER SECURID display.ro Counter .1.3.6.1.4.1.33.10.20.11 |
securIDSecureLoginsThe number of successful user logins on ports for
which SecurID user verification is enabled.
Corresponds directly to the value labeled
'Successful Logins:' in the SERVER SECURID
display.ro Counter .1.3.6.1.4.1.33.10.20.12 |
securIDSecureLoginsFailedThe number of verification failures due to
incorrect PASSCODE for attempted user logins
on ports for which SecurID user verification is
enabled. Corresponds directly to the value labeled
'Unsuccessful Logins:' in the SERVER SECURID
display.ro Counter .1.3.6.1.4.1.33.10.20.13 |
securIDServerAccess0The number of times the system successfully
accessed the SecurID server0. Corresponds
directly to the value labeled 'Attempts to access:',
'Server0', and 'Successful:' in the SERVER SECURID
display.ro Counter .1.3.6.1.4.1.33.10.20.14 |
securIDServerAccessFailed0The number of times the system unsuccessfully
accessed the SecurID server0. Corresponds
directly to the value labeled 'Attempts to access:',
'Server0', and 'UnSuccessful:' in the SERVER SECURID
display.ro Counter .1.3.6.1.4.1.33.10.20.15 |
securIDServerAccess1The number of times the system successfully
accessed the SecurID server1. Corresponds
directly to the value labeled 'Attempts to access:',
'Server1', and 'Successful:' in the SERVER SECURID
display.ro Counter .1.3.6.1.4.1.33.10.20.16 |
securIDServerAccessFailed1The number of times the system unsuccessfully
accessed the SecurID server1. Corresponds
directly to the value labeled 'Attempts to access:',
'Server1', and 'UnSuccessful:' in the SERVER SECURID
display.ro Counter .1.3.6.1.4.1.33.10.20.17 |
securIDServerAccess2The number of times the system successfully
accessed the SecurID server2. Corresponds
directly to the value labeled 'Attempts to access:',
'Server2', and 'Successful:' in the SERVER SECURID
display.ro Counter .1.3.6.1.4.1.33.10.20.18 |
securIDServerAccessFailed2The number of times the system unsuccessfully
accessed the SecurID server2. Corresponds
directly to the value labeled 'Attempts to access:',
'Server2', and 'UnSuccessful:' in the SERVER SECURID
display.ro Counter .1.3.6.1.4.1.33.10.20.19 |
securIDServerAccess3The number of times the system successfully
accessed the SecurID server3. Corresponds
directly to the value labeled 'Attempts to access:',
'Server3', and 'Successful:' in the SERVER SECURID
display.ro Counter .1.3.6.1.4.1.33.10.20.20 |
securIDServerAccessFailed3The number of times the system unsuccessfully
accessed the SecurID server3. Corresponds
directly to the value labeled 'Attempts to access:',
'Server3', and 'UnSuccessful:' in the SERVER SECURID
display.ro Counter .1.3.6.1.4.1.33.10.20.21 |
securIDServerAccess4The number of times the system successfully
accessed the SecurID server4. Corresponds
directly to the value labeled 'Attempts to access:',
'Server4', and 'Successful:' in the SERVER SECURID
display.ro Counter .1.3.6.1.4.1.33.10.20.22 |
securIDServerAccessFailed4The number of times the system unsuccessfully
accessed the SecurID server4. Corresponds
directly to the value labeled 'Attempts to access:',
'Server4', and 'UnSuccessful:' in the SERVER SECURID
display.ro Counter .1.3.6.1.4.1.33.10.20.23 |
securIDErrorPortIndexThe index of the most recent port on which a SecurID
access violation occurred. Corresponds
directly to the value labeled 'Last Unsuccessful
Login:' in the SERVER SECURID display.ro INTEGER .1.3.6.1.4.1.33.10.20.24 |
securIDErrorThe error number of the most recent SecurID-related
error. Corresponds directly to the value labeled
'Reason:' in the SERVER SECURID display. See
MRV In-Reach documentation for a complete list of
error numbers and their meaning.ro INTEGER .1.3.6.1.4.1.33.10.20.25 |
securIDErrorUsernameThe username associated with the most recent
SecurID-related error. Corresponds directly to the value
labeled 'Username:' in the SERVER SECURID display.ro DisplayString .1.3.6.1.4.1.33.10.20.26 |
securIDPortTableA list of SecurID character port entries. SEQUENCE OF SecurIDPortEntry .1.3.6.1.4.1.33.10.20.27 |
securIDPortEntryParameter values for a SecurID port. SecurIDPortEntry .1.3.6.1.4.1.33.10.20.27.1 |
securIDPortIndexAn index value that uniquely identifies a port
could relate to SecurID. The port identified by a
particular value of this index is the same port as
identified by charPortIndex in the Proposed Standard
Internet Character MIB.ro INTEGER .1.3.6.1.4.1.33.10.20.27.1.1 |
securIDPortStatusA control indicating the level of SecurID
operation on the port. Corresponds directly to PORT
SECURID and the value 'SecurID' following the
label 'Enabled Characteristics' in the PORT
CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.10.20.27.1.2 |
xSsh OBJECT IDENTIFIER .1.3.6.1.4.1.33.10.23 |
sshPortTableA list of SSH port entries SEQUENCE OF SshPortEntry .1.3.6.1.4.1.33.10.23.1 |
sshPortEntryParameter values for an SSH port. SshPortEntry .1.3.6.1.4.1.33.10.23.1.1 |
sshPortIndexAn index value that uniquely identifies an SSH port. The port
identified by a particular value of this index is the same port as
identified by charPortIndex in the proposed standard Internet
Character MIB.ro INTEGER .1.3.6.1.4.1.33.10.23.1.1.1 |
sshPortIncomingTcpPortSpecifies the TCP port number used to identify the port when a SSH
connection request arrives at the server. The default for a physical
port is 2022 + 100 * port's physical port number. The default is 22
for virtual ports. Corresponds directly to the value labeled 'Remote
Port:' in the PORT SSH CHARACTERISTICS display.rw INTEGER .1.3.6.1.4.1.33.10.23.1.1.2 |
sshPortNewlineFilteringTranslation to apply to newline sequences (CR/NULL or CR/LF) received
from the network during a SSH session, before sending the newline to
the character port. The value indicates which input sequence is
converted to which output sequence and sent to the
character port, with 'none' meaning no translation.
Corresponds directly to the value labeled 'Newline Filtering:'
in the PORT SSH CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.10.23.1.1.3 |
sshPortNewlineTranslation to apply to newline (carriage return) received from the
character port during an SSH session, before sending the newline to the
remote partner. Corresponds directly to the value labeled 'Newline:'
in the PORT SSH CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.10.23.1.1.4 |
sshPortTransmitBufferedTimeNumber of milliseconds to wait before transmitting data received from
a character port during an interactive SSH session.
Corresponds directly to the value labeled 'Transmit Buffered Time:' in
the PORT SSH CHARACTERISTICS display.rw INTEGER .1.3.6.1.4.1.33.10.23.1.1.5 |
sshPortRemoteProtocolIndicates which remote protocols will be accepted at this port.
Corresponds indirectly to the presence of 'Telnet' or 'SSH' under the
label 'Enabled Characteristics:' in the PORT SSH CHARACTERISTICS
display. If both protocols are accepted at the port, the choice of
protocol is determined by which features are enabled on the server with
SSH taking precedence over Telnet.rw Enumeration .1.3.6.1.4.1.33.10.23.1.1.6 |
sshPortBreakSequenceA sequence of characters, which together define the break function. If
this string is received from the SSH connection from across the network,
the port will send a hardware break out of the serial port. The first
character must be a carriage return ('\r'), and no more carriage
returns may appear in the sequence. The second character must not be
a NULL, or a line-feed ('\n'). Send a NULL to remove the break sequence.
If the sequence exists, it must have two to four characters.rw OCTET STRING .1.3.6.1.4.1.33.10.23.1.1.7 |
sshCipherMaskThis is a list of the encryption methods supported.
The OCTET STRING contains a bitmap, with one bit for each cipher type.
Corresponding bit numbers start with 0 as the low-order bit of the
second octet. The following bit positions are defined:
none(0), des(2), tripleDes(3), and blowfish(6). Corresponds directly to
the value labeled 'SSH Cipher Enabled:' in the SERVER SSH
CHARACTERISTICS display.rw OCTET STRING .1.3.6.1.4.1.33.10.23.2 |
sshAuthenticationTimeoutThe timeout in minutes before disconnecting if no successful
authentication of SSH parties has been made. Corresponds directly to
the value labeled 'Authentication Timeout:' in the SERVER SSH
CHARACTERISTICS display.rw INTEGER .1.3.6.1.4.1.33.10.23.3 |
sshHostKeyLengthThe bit length of the SSH host encryption key. When modified, the
desired change does not occur until the next system initialization.
Corresponds directly to the value labeled 'Host Key Length:' in the
SERVER SSH CHARACTERISTICS display.rw INTEGER .1.3.6.1.4.1.33.10.23.4 |
sshHostKeyGenerateFor a set-request with a value of generate or update, a new host key
will be generated in the background. When modified with generate, the
desired change does not occur until the next system initialization
whereas when modified with update the change goes into effect upon
completion of the new key.
In response to a get-request or a get-next-request the agent will
respond ready except when a host key is being created in which case
the agent responds generate.rw Enumeration .1.3.6.1.4.1.33.10.23.5 |
sshServerKeyLengthThe bit length of the SSH server encryption key. The difference between
the server and host key lengths should be greater than 128 bits.
Corresponds directly to the value labeled 'Server Key Length:' in the
SERVER SSH CHARACTERISTICS display.rw INTEGER .1.3.6.1.4.1.33.10.23.6 |
sshServerKeyTtlThe time in minutes that the server key remains valid. After this time
the server key is automatically re-generated. Corresponds directly to
the value labeled 'Server Key Timeout:' in the SERVER SSH
CHARACTERISTICS display.rw INTEGER .1.3.6.1.4.1.33.10.23.7 |
sshServerMaxBufferSizeThe size of the four buffers used by SSH for input and
output. These buffers are used for data coming from the
console, going to the network, coming from the network and
going to the console.rw INTEGER .1.3.6.1.4.1.33.10.23.8 |