MRV-IN-REACH-CHARACTER-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for MRV-IN-REACH-CHARACTER-MIB.
588
Objects
Active
Status
7
Dependencies
Imported Objects
Objects
588 total| Object Name |
|---|
contactClosureChangedIndication that the contact closure transitioned to open or closed. TRAP-TYPE .1.3.6.1.4.1.33.0.30 |
powerAlarmFuseBankAIndicates that a fuse from bank A tripped its breaker, or that
it went operational. However, it is unlikely that a trap would
be issued when the fuse starts working. TRAP-TYPE .1.3.6.1.4.1.33.0.31 |
powerAlarmFuseBankBIndicates that a fuse from bank B tripped its breaker, or that
it went operational. However, it is unlikely that a trap would
be issued when the fuse starts working. TRAP-TYPE .1.3.6.1.4.1.33.0.32 |
powerSupplyAlarmAIndicates that power supply A lost or regained power.
However, it is unlikely that a trap would be issued when the
power comes on. TRAP-TYPE .1.3.6.1.4.1.33.0.33 |
powerSupplyAlarmBIndicates that power supply B lost or regained power.
However, it is unlikely that a trap would be issued when the
power comes on. TRAP-TYPE .1.3.6.1.4.1.33.0.34 |
portInputSignalChangeIndicates that an input signal on a port has transitioned to
the state indicated in the variable rs232InSigState. TRAP-TYPE .1.3.6.1.4.1.33.0.35 |
portOutputSignalChangeIndicates that an output signal on a port has transitioned to
the state indicated in the variable rs232OutSigState. TRAP-TYPE .1.3.6.1.4.1.33.0.36 |
humidityThresholdExceededIndication that the humidity exceeded a threshhold and
the value of the currrent humidity. TRAP-TYPE .1.3.6.1.4.1.33.0.37 |
temperatureThresholdExceededIndication that the temperature exceeded a threshhold and
the value of the currrent temperature. TRAP-TYPE .1.3.6.1.4.1.33.0.38 |
alarmMasterNotRespondingIndication that the high density alarm management device lost
or regained contact with the inReach port to which it was
connected as indicated by the basicPortAlarmMasterStatus
variable. TRAP-TYPE .1.3.6.1.4.1.33.0.39 |
alarmMasterInputStateChangeIndication that the alarm input point within a high density alarm
management port transitioned to open or closed. TRAP-TYPE .1.3.6.1.4.1.33.0.41 |
asciiToTrapTranslationThis trap contains ASCII data, which arrived at serial port,
was formatted as a trap, and sent out on the network. TRAP-TYPE .1.3.6.1.4.1.33.0.42 |
powerMasterNotRespondingIndication that the power management port lost or regained
contact with the power unit to which it was connected as
indicated by the basicPortPowerMasterDeviceStatus variable. TRAP-TYPE .1.3.6.1.4.1.33.0.43 |
temperatureNormalIndication that the temperature returned within bounds, and
the value of the currrent temperature. TRAP-TYPE .1.3.6.1.4.1.33.0.44 |
humidityNormalIndication that the humidity returned within bounds, and
the currrent humidity reading. TRAP-TYPE .1.3.6.1.4.1.33.0.45 |
alarmMasterSideAOffIndication that side A powered off in the attached IR7104
alarm unit due to DC rail fluctuations. TRAP-TYPE .1.3.6.1.4.1.33.0.46 |
alarmMasterSideBOffIndication that side B powered off in the attached IR7104
alarm unit due to DC rail fluctuations. TRAP-TYPE .1.3.6.1.4.1.33.0.47 |
alarmMasterSideAOnIndication that side A powered on in the attached IR7104
alarm unit after previous power off. TRAP-TYPE .1.3.6.1.4.1.33.0.48 |
alarmMasterSideBOnIndication that side B powered on in the attached IR7104
alarm unit after previous power off. TRAP-TYPE .1.3.6.1.4.1.33.0.49 |
icmpPingHostNotReachableIndication that the icmp Ping Host is not reachable after
polling for icmpPingHostMaximumRetries. TRAP-TYPE .1.3.6.1.4.1.33.0.50 |
icmpPingHostRespondingIndication that the icmp Ping Host is reachable again after
a failure. TRAP-TYPE .1.3.6.1.4.1.33.0.51 |
alarmInputLowDensity0001AlarmGenerated when alarm point 1 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10001 |
alarmInputLowDensity0002AlarmGenerated when alarm point 2 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10002 |
alarmInputLowDensity0003AlarmGenerated when alarm point 3 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10003 |
alarmInputLowDensity0004AlarmGenerated when alarm point 4 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10004 |
alarmInputLowDensity0005AlarmGenerated when alarm point 5 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10005 |
alarmInputLowDensity0006AlarmGenerated when alarm point 6 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10006 |
alarmInputLowDensity0007AlarmGenerated when alarm point 7 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10007 |
alarmInputLowDensity0008AlarmGenerated when alarm point 8 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10008 |
alarmInputLowDensity0009AlarmGenerated when alarm point 9 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10009 |
alarmInputLowDensity0010AlarmGenerated when alarm point 10 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10010 |
alarmInputLowDensity0011AlarmGenerated when alarm point 11 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10011 |
alarmInputLowDensity0012AlarmGenerated when alarm point 12 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10012 |
alarmInputLowDensity0013AlarmGenerated when alarm point 13 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10013 |
alarmInputLowDensity0014AlarmGenerated when alarm point 14 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10014 |
alarmInputLowDensity0015AlarmGenerated when alarm point 15 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10015 |
alarmInputLowDensity0016AlarmGenerated when alarm point 16 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10016 |
alarmInputLowDensity0017AlarmGenerated when alarm point 17 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10017 |
alarmInputLowDensity0018AlarmGenerated when alarm point 18 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10018 |
alarmInputLowDensity0019AlarmGenerated when alarm point 19 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10019 |
alarmInputLowDensity0020AlarmGenerated when alarm point 20 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10020 |
alarmInputLowDensity0021AlarmGenerated when alarm point 21 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10021 |
alarmInputLowDensity0022AlarmGenerated when alarm point 22 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10022 |
alarmInputLowDensity0023AlarmGenerated when alarm point 23 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10023 |
alarmInputLowDensity0024AlarmGenerated when alarm point 24 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10024 |
alarmInputLowDensity0025AlarmGenerated when alarm point 25 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10025 |
alarmInputLowDensity0026AlarmGenerated when alarm point 26 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10026 |
alarmInputLowDensity0027AlarmGenerated when alarm point 27 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10027 |
alarmInputLowDensity0028AlarmGenerated when alarm point 28 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10028 |
alarmInputLowDensity0029AlarmGenerated when alarm point 29 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10029 |
alarmInputLowDensity0030AlarmGenerated when alarm point 30 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10030 |
alarmInputLowDensity0031AlarmGenerated when alarm point 31 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10031 |
alarmInputLowDensity0032AlarmGenerated when alarm point 32 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10032 |
alarmInputLowDensity0033AlarmGenerated when alarm point 33 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10033 |
alarmInputLowDensity0034AlarmGenerated when alarm point 34 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10034 |
alarmInputLowDensity0035AlarmGenerated when alarm point 35 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10035 |
alarmInputLowDensity0036AlarmGenerated when alarm point 36 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10036 |
alarmInputLowDensity0037AlarmGenerated when alarm point 37 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10037 |
alarmInputLowDensity0038AlarmGenerated when alarm point 38 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10038 |
alarmInputLowDensity0039AlarmGenerated when alarm point 39 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10039 |
alarmInputLowDensity0040AlarmGenerated when alarm point 40 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10040 |
alarmInputLowDensity0041AlarmGenerated when alarm point 41 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10041 |
alarmInputLowDensity0042AlarmGenerated when alarm point 42 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10042 |
alarmInputLowDensity0043AlarmGenerated when alarm point 43 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10043 |
alarmInputLowDensity0044AlarmGenerated when alarm point 44 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10044 |
alarmInputLowDensity0045AlarmGenerated when alarm point 45 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10045 |
alarmInputLowDensity0046AlarmGenerated when alarm point 46 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10046 |
alarmInputLowDensity0047AlarmGenerated when alarm point 47 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10047 |
alarmInputLowDensity0048AlarmGenerated when alarm point 48 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10048 |
alarmInputLowDensity0049AlarmGenerated when alarm point 49 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10049 |
alarmInputLowDensity0050AlarmGenerated when alarm point 50 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10050 |
alarmInputLowDensity0051AlarmGenerated when alarm point 51 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10051 |
alarmInputLowDensity0052AlarmGenerated when alarm point 52 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10052 |
alarmInputLowDensity0053AlarmGenerated when alarm point 53 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10053 |
alarmInputLowDensity0054AlarmGenerated when alarm point 54 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10054 |
alarmInputLowDensity0055AlarmGenerated when alarm point 55 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10055 |
alarmInputLowDensity0056AlarmGenerated when alarm point 56 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10056 |
alarmInputLowDensity0057AlarmGenerated when alarm point 57 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10057 |
alarmInputLowDensity0058AlarmGenerated when alarm point 58 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10058 |
alarmInputLowDensity0059AlarmGenerated when alarm point 59 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10059 |
alarmInputLowDensity0060AlarmGenerated when alarm point 60 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10060 |
alarmInputLowDensity0061AlarmGenerated when alarm point 61 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10061 |
alarmInputLowDensity0062AlarmGenerated when alarm point 62 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10062 |
alarmInputLowDensity0063AlarmGenerated when alarm point 63 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10063 |
alarmInputLowDensity0064AlarmGenerated when alarm point 64 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10064 |
alarmInputLowDensity0065AlarmGenerated when alarm point 65 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10065 |
alarmInputLowDensity0066AlarmGenerated when alarm point 66 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10066 |
alarmInputLowDensity0067AlarmGenerated when alarm point 67 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10067 |
alarmInputLowDensity0068AlarmGenerated when alarm point 68 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10068 |
alarmInputLowDensity0069AlarmGenerated when alarm point 69 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10069 |
alarmInputLowDensity0070AlarmGenerated when alarm point 70 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10070 |
alarmInputLowDensity0071AlarmGenerated when alarm point 71 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10071 |
alarmInputLowDensity0072AlarmGenerated when alarm point 72 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10072 |
alarmInputLowDensity0073AlarmGenerated when alarm point 73 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10073 |
alarmInputLowDensity0074AlarmGenerated when alarm point 74 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10074 |
alarmInputLowDensity0075AlarmGenerated when alarm point 75 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10075 |
alarmInputLowDensity0076AlarmGenerated when alarm point 76 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10076 |
alarmInputLowDensity0077AlarmGenerated when alarm point 77 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10077 |
alarmInputLowDensity0078AlarmGenerated when alarm point 78 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10078 |
alarmInputLowDensity0079AlarmGenerated when alarm point 79 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10079 |
alarmInputLowDensity0080AlarmGenerated when alarm point 80 from a low density unit
transitions to the alarm state. TRAP-TYPE .1.3.6.1.4.1.33.0.10080 |
alarmInputLowDensity0001NormalGenerated when alarm point 1 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20001 |
alarmInputLowDensity0002NormalGenerated when alarm point 2 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20002 |
alarmInputLowDensity0003NormalGenerated when alarm point 3 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20003 |
alarmInputLowDensity0004NormalGenerated when alarm point 4 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20004 |
alarmInputLowDensity0005NormalGenerated when alarm point 5 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20005 |
alarmInputLowDensity0006NormalGenerated when alarm point 6 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20006 |
alarmInputLowDensity0007NormalGenerated when alarm point 7 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20007 |
alarmInputLowDensity0008NormalGenerated when alarm point 8 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20008 |
alarmInputLowDensity0009NormalGenerated when alarm point 9 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20009 |
alarmInputLowDensity0010NormalGenerated when alarm point 10 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20010 |
alarmInputLowDensity0011NormalGenerated when alarm point 11 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20011 |
alarmInputLowDensity0012NormalGenerated when alarm point 12 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20012 |
alarmInputLowDensity0013NormalGenerated when alarm point 13 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20013 |
alarmInputLowDensity0014NormalGenerated when alarm point 14 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20014 |
alarmInputLowDensity0015NormalGenerated when alarm point 15 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20015 |
alarmInputLowDensity0016NormalGenerated when alarm point 16 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20016 |
alarmInputLowDensity0017NormalGenerated when alarm point 17 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20017 |
alarmInputLowDensity0018NormalGenerated when alarm point 18 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20018 |
alarmInputLowDensity0019NormalGenerated when alarm point 19 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20019 |
alarmInputLowDensity0020NormalGenerated when alarm point 20 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20020 |
alarmInputLowDensity0021NormalGenerated when alarm point 21 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20021 |
alarmInputLowDensity0022NormalGenerated when alarm point 22 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20022 |
alarmInputLowDensity0023NormalGenerated when alarm point 23 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20023 |
alarmInputLowDensity0024NormalGenerated when alarm point 24 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20024 |
alarmInputLowDensity0025NormalGenerated when alarm point 25 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20025 |
alarmInputLowDensity0026NormalGenerated when alarm point 26 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20026 |
alarmInputLowDensity0027NormalGenerated when alarm point 27 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20027 |
alarmInputLowDensity0028NormalGenerated when alarm point 28 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20028 |
alarmInputLowDensity0029NormalGenerated when alarm point 29 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20029 |
alarmInputLowDensity0030NormalGenerated when alarm point 30 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20030 |
alarmInputLowDensity0031NormalGenerated when alarm point 31 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20031 |
alarmInputLowDensity0032NormalGenerated when alarm point 32 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20032 |
alarmInputLowDensity0033NormalGenerated when alarm point 33 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20033 |
alarmInputLowDensity0034NormalGenerated when alarm point 34 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20034 |
alarmInputLowDensity0035NormalGenerated when alarm point 35 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20035 |
alarmInputLowDensity0036NormalGenerated when alarm point 36 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20036 |
alarmInputLowDensity0037NormalGenerated when alarm point 37 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20037 |
alarmInputLowDensity0038NormalGenerated when alarm point 38 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20038 |
alarmInputLowDensity0039NormalGenerated when alarm point 39 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20039 |
alarmInputLowDensity0040NormalGenerated when alarm point 40 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20040 |
alarmInputLowDensity0041NormalGenerated when alarm point 41 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20041 |
alarmInputLowDensity0042NormalGenerated when alarm point 42 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20042 |
alarmInputLowDensity0043NormalGenerated when alarm point 43 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20043 |
alarmInputLowDensity0044NormalGenerated when alarm point 44 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20044 |
alarmInputLowDensity0045NormalGenerated when alarm point 45 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20045 |
alarmInputLowDensity0046NormalGenerated when alarm point 46 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20046 |
alarmInputLowDensity0047NormalGenerated when alarm point 47 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20047 |
alarmInputLowDensity0048NormalGenerated when alarm point 48 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20048 |
alarmInputLowDensity0049NormalGenerated when alarm point 49 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20049 |
alarmInputLowDensity0050NormalGenerated when alarm point 50 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20050 |
alarmInputLowDensity0051NormalGenerated when alarm point 51 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20051 |
alarmInputLowDensity0052NormalGenerated when alarm point 52 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20052 |
alarmInputLowDensity0053NormalGenerated when alarm point 53 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20053 |
alarmInputLowDensity0054NormalGenerated when alarm point 54 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20054 |
alarmInputLowDensity0055NormalGenerated when alarm point 55 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20055 |
alarmInputLowDensity0056NormalGenerated when alarm point 56 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20056 |
alarmInputLowDensity0057NormalGenerated when alarm point 57 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20057 |
alarmInputLowDensity0058NormalGenerated when alarm point 58 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20058 |
alarmInputLowDensity0059NormalGenerated when alarm point 59 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20059 |
alarmInputLowDensity0060NormalGenerated when alarm point 60 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20060 |
alarmInputLowDensity0061NormalGenerated when alarm point 61 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20061 |
alarmInputLowDensity0062NormalGenerated when alarm point 62 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20062 |
alarmInputLowDensity0063NormalGenerated when alarm point 63 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20063 |
alarmInputLowDensity0064NormalGenerated when alarm point 64 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20064 |
alarmInputLowDensity0065NormalGenerated when alarm point 65 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20065 |
alarmInputLowDensity0066NormalGenerated when alarm point 66 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20066 |
alarmInputLowDensity0067NormalGenerated when alarm point 67 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20067 |
alarmInputLowDensity0068NormalGenerated when alarm point 68 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20068 |
alarmInputLowDensity0069NormalGenerated when alarm point 69 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20069 |
alarmInputLowDensity0070NormalGenerated when alarm point 70 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20070 |
alarmInputLowDensity0071NormalGenerated when alarm point 71 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20071 |
alarmInputLowDensity0072NormalGenerated when alarm point 72 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20072 |
alarmInputLowDensity0073NormalGenerated when alarm point 73 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20073 |
alarmInputLowDensity0074NormalGenerated when alarm point 74 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20074 |
alarmInputLowDensity0075NormalGenerated when alarm point 75 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20075 |
alarmInputLowDensity0076NormalGenerated when alarm point 76 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20076 |
alarmInputLowDensity0077NormalGenerated when alarm point 77 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20077 |
alarmInputLowDensity0078NormalGenerated when alarm point 78 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20078 |
alarmInputLowDensity0079NormalGenerated when alarm point 79 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20079 |
alarmInputLowDensity0080NormalGenerated when alarm point 80 from a low density unit
transitions to the normal state. TRAP-TYPE .1.3.6.1.4.1.33.0.20080 |
characterDep OBJECT IDENTIFIER .1.3.6.1.4.1.33.2 |
RFC1213-MIB Unknown .1.3.6.1.4.1.33.2 |
xCharacter OBJECT IDENTIFIER .1.3.6.1.4.1.33.13 |
xBasic OBJECT IDENTIFIER .1.3.6.1.4.1.33.13.1 |
basicBroadcastControl for user ability to broadcast messages to
other local ports. Corresponds directly to SERVER
BROADCAST and the presence of the label 'Broadcast'
following the label 'Enabled Characteristics:' in
the SERVER CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.13.1.1 |
basicErrorReportControl for server display of an error when the
user gives an unsupported command. Corresponds
directly to SERVER REPORT ERRORS and the presence of
the label 'Report Errors' following the label
'Enabled Characteristics:' in the SERVER
CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.13.1.2 |
basicLockControl for user ability to use a password to
protect a logged in terminal from other users.
Corresponds directly to SERVER LOCK and the presence
of the label 'Lock' following the label 'Enabled
Characteristics:' in the SERVER CHARACTERISTICS
display.rw Enumeration .1.3.6.1.4.1.33.13.1.3 |
basicInactivityTimerNumber of minutes a terminal may remain logged in
with no sessions, no input or output, and no modem
transitions. Corresponds directly to SERVER
INACTIVITY TIMER and the value labeled 'Inactivity
Timer:' in the SERVER CHARACTERISTICS display.rw INTEGER .1.3.6.1.4.1.33.13.1.4 |
basicPasswordRetryLimitNumber of times the server allows a user to retry
an incorrect password. Corresponds directly to
SERVER PASSWORD LIMIT and the value labeled
'Password Limit:' in the SERVER CHARACTERISTICS
display.rw INTEGER .1.3.6.1.4.1.33.13.1.5 |
basicPrivilegedPasswordThe password a user must enter to become
privileged.
For security reasons, reading this object always
returns a zero-length value. Corresponds directly
to SERVER PRIVILEGED PASSWORD.rw DisplayString .1.3.6.1.4.1.33.13.1.6 |
basicLoginPasswordThe password a user must enter to be given the
opportunity to log in. For security reasons,
reading this object always returns a zero-length
value. Corresponds directly to SERVER LOGIN
PASSWORD.rw DisplayString .1.3.6.1.4.1.33.13.1.7 |
basicLoginPromptThe text string the server displays to prompt a
user for the login password. Corresponds directly
to SERVER LOGIN PROMPT.rw DisplayString .1.3.6.1.4.1.33.13.1.8 |
basicWelcomeThe text string the server displays before
attempting to log in a user. Corresponds directly
to SERVER WELCOME and the value labeled 'Welcome:'
in the SERVER CHARACTERISTICS display.rw DisplayString .1.3.6.1.4.1.33.13.1.9 |
basicActivePortsThe number of ports with connected sessions or
logged in users. Corresponds directly to the value
labeled 'Active Ports:' and 'Cur' in the SERVER
STATUS display.ro Gauge .1.3.6.1.4.1.33.13.1.10 |
basicActivePortsHighThe highest value of basicActivePorts since system
initialization. Corresponds directly to the value
labeled 'Active Ports:' and 'High' in the SERVER
STATUS display.ro Gauge .1.3.6.1.4.1.33.13.1.11 |
basicActiveUsersThe number of logged in users. Corresponds
directly to the value labeled 'Active Users:' and
'Cur' in the SERVER STATUS display.ro Gauge .1.3.6.1.4.1.33.13.1.12 |
basicActiveUsersHighThe highest value of basicActiveUsers since system
initialization. Corresponds directly to the value
labeled 'Active Users:' and 'High' in the SERVER
STATUS display.ro Gauge .1.3.6.1.4.1.33.13.1.13 |
basicSessionsThe total number of connected sessions.
Corresponds directly to the value labeled 'Connected
Sessions:' and 'Cur' in the SERVER STATUS display.ro Gauge .1.3.6.1.4.1.33.13.1.14 |
basicSessionsHighThe highest value of basicSessions since system
initialization. Corresponds directly to the value
labeled 'Connected Sessions:' and 'High' in the
SERVER STATUS display.ro Gauge .1.3.6.1.4.1.33.13.1.15 |
basicSessionsLimitThe maximum total number of sessions that can
simultaneously be connected to the system. A value
of -1 indicates no limit up to available dynamic
system memory. Corresponds directly to SERVER
SESSION LIMIT and the value labeled 'Connected
Sessions:' and 'Max' in the SERVER STATUS display.rw INTEGER (-1..255) .1.3.6.1.4.1.33.13.1.16 |
basicPortTableA list of basic character port entries. SEQUENCE OF BasicPortEntry .1.3.6.1.4.1.33.13.1.17 |
basicPortEntryBasic parameter values for a port. BasicPortEntry .1.3.6.1.4.1.33.13.1.17.1 |
basicPortIndexAn index value that uniquely identifies a port.
The port identified by a particular value of this
index is the same port as identified by
charPortIndex in the standard Character MIB.ro INTEGER .1.3.6.1.4.1.33.13.1.17.1.1 |
basicPortDefaultDestActionThe action to take relative to
basicPortDefaultDestName. Corresponds directly to
PORT DEDICATED/PREFERRED SERVICE and the label
'Dedicated/Preferred Service:' in the PORT
CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.2 |
basicPortDefaultDestProtocolThe session protocol to use with
basicPortDefaultDestName. Corresponds directly to
LAT/TELNET PORT DEDICATED/PREFERRED SERVICE.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.3 |
basicPortDefaultDestNameThe default name to use in forming a connection
when no other name is specified. Corresponds
directly to PORT DEDICATED/PREFERRED SERVICE and the
value labeled 'Dedicated/Preferred Service:' in the
PORT CHARACTERISTICS display. If the value of
basicPortDefaultDestProtocol is 'telnet', an
Internet port number may be included on the end of
the name, delimited with a colon (':'). If the
value of basicPortDefaultDestProtocol is not
'telnet', then the maximum length is 16.rw DisplayString .1.3.6.1.4.1.33.13.1.17.1.4 |
basicPortDefaultDestLATNodeNameA LAT node name to use with
basicPortDefaultDestName. Corresponds directly to
PORT DEDICATED/PREFERRED SERVICE NODE and the value
labeled 'Node:' following the label
'Dedicated/Preferred Service:' in the PORT
CHARACTERISTICS display. This object can have a
non- zero-length value only if the value of
basicPortDefaultDestProtocol is 'lat'.rw DisplayString .1.3.6.1.4.1.33.13.1.17.1.5 |
basicPortDefaultDestLATPortNameA LAT port name to use with
basicPortDefaultDestName. Corresponds directly to
PORT DEDICATED/PREFERRED SERVICE NODE and the value
labeled 'Node:' following the label
'Dedicated/Preferred Service:' in the PORT
CHARACTERISTICS display. this object can hav a
non-zero-length value only if the value if
basicPortDefaultDestProtocol is 'lat'rw DisplayString .1.3.6.1.4.1.33.13.1.17.1.6 |
basicPortAutoConnectControl for automatic session connection.
Corresponds directly to PORT AUTOCONNECT and the
presence of the label 'Autoconnect' following the
label 'Enabled Characteristics:' in the PORT
CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.7 |
basicPortAutoLoginControl for automatic port login. Corresponds
directly to PORT AUTODEDICATED and the presence of
the label 'Autodedicated' following the label
'Enabled Characteristics:' in the PORT
CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.8 |
basicPortBroadcastControl for display of messages sent by users on
other ports. Corresponds directly to PORT BROADCAST
and the presence of the label 'Broadcast' following
the label 'Enabled Characteristics:' in the PORT
CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.9 |
basicPortConnectResumeControl for behavior of a connection attempt to a
destination where the port already has a connection.
'disabled' causes a new connection. 'enabled'
causes the existing connection to become the active
connection. Corresponds directly to PORT
CONNECTRESUME and the presence of the label
'Connectresume' following the label 'Enabled
Characteristics:' in the PORT CHARACTERISTICS
display.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.10 |
basicPortDialupDefines whether the port should be considered as
connected to a dialup line. 'enabled' means that it
is. Corresponds directly to PORT DIALUP and the
presence of the label 'Dial Up' following the label
'Enabled Characteristics:' in the PORT
CHARACTERISTICS display. This object is not available
on units that do not support modem signals (ie 2220).rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.11 |
basicPortIdleTimeoutThe number of minutes the system will allow a
session to have no activity before automatically
disconnecting it. A value of -1 indicates no
timeout. Zero is not a valid value. Corresponds
directly to PORT IDLE TIMEOUT and the value labeled
'Idle Timeout:' in the PORT ALTERNATE
CHARACTERISTICS display.rw INTEGER (-1..480) .1.3.6.1.4.1.33.13.1.17.1.12 |
basicPortInactivityLogoutControl for the system automatically logging the
port out when it has no sessions, no local activity,
and no modem signal changes for the time period
specified by basicInactivityTimer. Corresponds
directly to PORT INACTIVITY LOGOUT and the presence
of the label 'Inactivity Logout' following the label
'Enabled Characteristics:' in the PORT
CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.13 |
basicPortLossNotificationControl for the system sending a Bell character to
the port when it looses an input character due to an
overrun or data error. Corresponds directly to PORT
LOSS NOTIFICATION and the presence of the label
'Loss Notification' following the label 'Enabled
Characteristics:' in the PORT CHARACTERISTICS
display.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.14 |
basicPortMessageCodesControl for including error numbers in error
messages displayed on the port. Corresponds
directly to PORT MESSAGE CODES and the presence of
the label 'Message Codes' following the label
'Enabled Characteristics:' in the PORT
CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.15 |
basicPortMultisessionsControl for running the multisession line protocol
between the port and the locally-connected terminal.
Corresponds directly to PORT MULTISESSIONS and the
presence of the label 'Multisessions' following the
label 'Enabled Characteristics:' in the PORT
CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.16 |
basicPortDefaultUserNameDefault user name to use for automatically logging
in the port. Corresponds directly to PORT USERNAME
and the value labeled 'Port n:' in the PORT
CHARACTERISTICS display.rw DisplayString .1.3.6.1.4.1.33.13.1.17.1.17 |
basicPortVerificationControl for display of informational messages on
the port when the user connects, disconnects, or
switches a session. Corresponds directly to PORT
VERIFICATION and the presence of the label
'Verification' following the label 'Enabled
Characteristics:' in the PORT CHARACTERISTICS
display.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.18 |
basicPortDefaultProtocolThe session protocol to use when not otherwise
specified. Corresponds directly to PORT RESOLVE
SERVICE and the value labeled 'Resolve Service:' in
the PORT ALTERNATE CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.19 |
basicPortLoginsThe number of logins on the port since system
initialization. Corresponds directly to the value
labeled 'Local Accesses:' in the PORT COUNTERS
display.ro Counter .1.3.6.1.4.1.33.13.1.17.1.20 |
basicPortRemoteSessionsThe number of remotely originating sessions to the
port since system initialization. Corresponds
directly to the value labeled 'Remote Accesses:' in
the PORT COUNTERS display.ro Counter .1.3.6.1.4.1.33.13.1.17.1.21 |
basicPortIdleTimeoutsThe number of session disconnects due to expiration
of basicPortIdleTimeout. Corresponds directly to
the value labeled 'Idle Timeouts:' in the PORT
COUNTERS display.ro Counter .1.3.6.1.4.1.33.13.1.17.1.22 |
basicPortStatusThe current operational status of the port.
Corresponds directly to the value labeled 'Status:'
in the PORT STATUS display.ro Enumeration .1.3.6.1.4.1.33.13.1.17.1.23 |
basicPortLastInCharacterThe character that most recently came into the
port. Corresponds directly to the value labeled
'Last Char Input:' in the PORT STATUS display.ro INTEGER .1.3.6.1.4.1.33.13.1.17.1.24 |
basicPortLastOutCharacterThe character that most recently went out of the
port. Corresponds directly to the value labeled
'Last Char Output:' in the PORT STATUS display.ro INTEGER .1.3.6.1.4.1.33.13.1.17.1.25 |
basicPortActiveUserNameThe user name currently logged into the port.
Corresponds directly to the value by the port number
and labeled 'Username' in the USERS display.ro DisplayString .1.3.6.1.4.1.33.13.1.17.1.26 |
basicPortDefaultSessionModeData recognition mode when starting a session,
with the following meanings:
interactive locally recognize all controls
binary recognize only session protocol
(corresponds to PASSALL)
binaryWithFlow recognize only XON and XOFF
(corresponds to PASTHRU
transparent recognize no data
Corresponds directly to PORT DEFAULT SESSION MODE
and the value labeled 'Default Session Mode:' in
the PORT ALTERNATE CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.27 |
basicPortZeroControl to zero counters for the port. In response
to a get-request or get-next-request, the agent
always returns 'ready' for this value. Setting the
value to 'ready' has no effect. Setting it to
'execute' causes the port's counters to be zeroed.
Corresponds to the ZERO PORT command.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.28 |
basicPortZeroTimeThe number of hundredths of a second since the most
recent zeroing of the port's counters, such as
through execution of basicPortZero. Corresponds
directly to the value labeled 'Seconds Since
Zeroed:' in the PORT COUNTERS display.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.33.13.1.17.1.29 |
basicPortUnixCommandsControl to allow the user to use Unix-style
commands the port.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.30 |
basicPortSessionModeData recognition mode for an active session, with
the following meanings:
interactive locally recognize all controls
binary recognize only session protocol
(corresponds to PASSALL)
binaryWithFlow recognize only XON and XOFF
(corresponds to PASTHRU
transparent recognize no data
noActiveSessions no sessions on this port.
This object can be set to values of 1 to 4, but
only if there is an active session on the port.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.31 |
basicPortRemoteDisconnectNotifyIf enabled, a BELL (ctrl G) will be sent out the
serial port when a remote session is disconnected
and the port is logged out.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.32 |
basicPortDefaultDestControlledA control to send preconfigured controlled port session
strings when entering or exiting a session established to
the basicPortDefaultDestName. Corresponds directly to the
value labeled '(Controlled)' following the label
'Dedicated/Preferred Service:' in the PORT CHARACTERISTICS
display.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.33 |
basicPortControlledPortLoginA control string to send out the serial port upon
port login. Corresponds to the hexadecimal code which is
represented in ASCII following the label
'Controlled Port Login:' in the PORT CONTROLLED display.rw OCTET STRING .1.3.6.1.4.1.33.13.1.17.1.34 |
basicPortControlledPortLogoutA control string to send out the serial port upon
port logout. Corresponds to the hexadecimal code which is
represented in ASCII following the label
'Controlled Port Logout:' in the PORT CONTROLLED display.rw OCTET STRING .1.3.6.1.4.1.33.13.1.17.1.35 |
basicPortControlledSessionInitializeA control string to send out the serial port upon
entering a session. Corresponds to the hexadecimal code
which represented in ASCII following the label
'Controlled Session Initialize:' in the PORT CONTROLLED
display.rw OCTET STRING .1.3.6.1.4.1.33.13.1.17.1.36 |
basicPortControlledSessionTerminateA control string to send out the serial port upon
exiting a session. Corresponds to the hexadecimal code
which is represented in ASCII following the label
'Controlled Session Terminate:' in the PORT CONTROLLED
display.rw OCTET STRING .1.3.6.1.4.1.33.13.1.17.1.37 |
basicPortRloginTransparentModeA control to pass x'ff' as binary data, not doubling x'ff'.
Similar to basicPortSessionMode = transparent but for
a rlogin session.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.38 |
basicPortLoginDurationThe amount of time in minutes that a port may remain logged in
regardless of the activity on the port. The value 0 indicates
that the timer is disabled. Corresponds directly to the value
labeled 'Login Duration:' in the PORT ALTERNATE CHARACTERISTICS
display.rw INTEGER .1.3.6.1.4.1.33.13.1.17.1.39 |
basicPortOutboundSecurityControl to disable outbound security, which can be either
Kerberos or SecureID, on a per port basis. Corresponds
directly to the presence of the value 'OutboundSecurity'
following the label 'Enabled Characteristics' in the PORT
CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.40 |
basicPortXonTimerIndicates the number of seconds between successive 'XON's sent
out a port. A zero signifies that the timer is disabled.
Corresponds directly to the value labeled 'Xon Send Timer:' in
the PORT ALTERNATE CHARACTERISTICS display.rw INTEGER ( 0..2550 ) .1.3.6.1.4.1.33.13.1.17.1.41 |
basicPortDefaultDedicatedSessionTypeThis integer is interpreted as a bit mask that specifies the
default session type for a
dedicated service for this port. The bit numbers are:
1;service name, 2;node name, 3;port name, 4, telnet
console; 5, rlogin; 6, bridge console; 7, chassis console.rw INTEGER ( 0..168 ) .1.3.6.1.4.1.33.13.1.17.1.42 |
basicPortIdleTimeReceiveControl to restrict the basicPortIdleTimeout to apply to data
received from the network and transmitted out the serial port.
Data received by the serial port will not be considered
activity. Corresponds directly to the value labeled 'Idle
Time Receive Mode:' in the PORT ALTERNATE CHARACTERISTICS
display.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.43 |
basicPortIdleTimeTransmitControl to restrict the basicPortIdleTimeout to apply to data
received from the serial port and transmitted out the LAN.
Data received from the network will not count as activity.
Corresponds directly to the value labeled 'Idle Time Transmit
Mode:' in the PORT ALTERNATE CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.44 |
basicPortZeroDisconnectSessionA control to disconnect a session at Port 0 when the
password limit is reached.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.45 |
basicPortConsolePortControl to configure this port as a console port. This
control is only valid on those models with variable
configuration ports. This object can only be set enabled;
and doing so will disable basicPortSensor
and basicPortAlarmControl.
A set will only update the permanent database. Use a
charPortReset for this change to take effect.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.46 |
basicPortLoginPasswordThe password a user must enter to be given the
opportunity to log in to a given port. For security
reasons reading this object always returns a zero-length
value. Corresponds directly to PORT LOGIN PASSWORD.rw DisplayString .1.3.6.1.4.1.33.13.1.17.1.47 |
basicPortSensorControl to configure this port as a temperature and humidity
sensor. This control is only valid on those models with
variable configuration ports. This object can only be set
enabled; and doing so will disable basicPortConsolePort
and basicPortAlarmControl.
A set will only update the permanent database. Use a
charPortReset for this change to take effect.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.48 |
basicPortAlarmControlControl to configure this port for alarm input and control
output. This control is
only valid on those models with variable configuration ports.
This object can only be set enabled; and doing so will
disable basicPortConsolePort and basicPortSensor.
A set will only update the permanent database. Use a
charPortReset for this change to take effect.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.49 |
basicPortCommandLoggingA control to toggle logging of commands at this port.
Command input may be logged from direct terminal
connections, session input from the LAN, or session output
to the LAN. Corresponds directly to the presence of 'Command
Logging' under the label 'Enabled Characteristics:' in the
PORT CHARACTERISTICS display. The desired change will not
take effect until the port is logged off.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.50 |
basicPortBreakSequenceA sequence of characters to be sent out the serial port on
receipt of a Break from the network in lieu of a hardware
break. The sequence entered by the user is converted into
an octet string up to four bytes long to be sent out the
serial port. For example, the user's representation of
octal 2, or '\002', takes four characters in
basicPortBreakSequence; but only one byte in the string
sent out the serial port.rw OCTET STRING .1.3.6.1.4.1.33.13.1.17.1.51 |
basicPortTl1ModeControls the TL1 mode of a port. Valid TL1 modes are human-
to-machine language (hml), machine-to-machine language
(mml), and MML without echo. MML is for direct connection
to another TL1 device whereas HML provides human prompts.
A change takes effect after logging out the port.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.53 |
basicPortTl1ConsoleControls whether this port becomes the TL1 console
receiving and displaying autonomous reports of alarm
events. A change takes effect after logging out the port.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.54 |
basicPortFallThroughControl to allow a user to login to a port after RADIUS
or SecurID authentication fails because the RADIUS servers
or SecurID servers are unavailable. When a user is logged
in via 'fallthrough', he is logged in to the port as a
non-privileged user. The change takes effect after logging
out the port.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.55 |
basicPortCommandLoggingSuppressControlCharactersControl to toggle suppression of control characters in the
command log. This object can only be set to enabled
when command logging is enabled on that port.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.56 |
basicPortDataLoggingControl to toggle data logging on the specified port.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.57 |
basicPortDataLoggingSuppressControlCharactersControl to toggle suppression of control characters in the
data log. This object can only be set to enabled
when data logging is enabled on that port.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.58 |
basicPortOnboardSecurityA control to toggle onboard security for this port where
the username and password are authenticated against an
internal access list. The desired change will not take
effect until the port is logged off.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.59 |
basicPortFallBackControl to allow a 'fallback' authentication mechanism
after RADIUS or SecurID authentication fails because the
RADIUS or SecurID servers are unavailable. Onboard
security, an internal security database, is
used for fallback authentication. The user in fallback
mode must enter a valid username and password to be
successfully logged in. The change takes effect after
logging out the port.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.60 |
basicPortAlarmMasterControl to configure this port for high densitiy alarm
input and control output management. This control is
only valid on those models with variable configuration ports.
This object can only be set enabled; and doing so will
disable basicPortConsolePort, basicPortSensor and
basicPortAlarmControl. A set will only update the permanent
database. Use a charPortReset for this change to take effect.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.61 |
basicPortAlarmMasterAccountingControl to toggle logging of alarm events on this port.
Use a charPortReset for this change to take effect.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.62 |
basicPortAlarmMasterAudibleAlarmControl whether the alarm will have an audible sound for
all alarm points attached to this port.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.63 |
basicPortAlarmMasterFixTimeTime in minutes between audible alarm soundings for an alarm
master port. This occurs after someone hits the master alarm
reset button. If there is at least one alarm condition on an
alarm point within the fix time, then the alarm will sound
again at the end of that fix time.rw INTEGER ( 1 .. 720 ) .1.3.6.1.4.1.33.13.1.17.1.64 |
basicPortAlarmMasterLcdDisplayStringUpdates the LCD display message for the high density
alarm unit attached to the port. Corresponds directly
to the DISPLAY AMST command.rw DisplayString .1.3.6.1.4.1.33.13.1.17.1.65 |
basicPortAlarmMasterRebootControl to reboot the high density alarm unit attached
to the port when set to 'execute'. In response to a
get-request or get-next-request, the agent always
returns 'ready' for this value. Setting the value
to 'ready' has no effect. Corresponds directly to the
REBOOT AMST command.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.66 |
basicPortAlarmMasterUpdateFirmwareHostThe internet address of the server to use when
downloading a new firmware image for the high density
alarm unit attached to this port via TFTP.
Corresponds directly to the UPDATE AMST FIRMWARE
command's INTERNET ADDRESS parameter.rw IpAddress .1.3.6.1.4.1.33.13.1.17.1.67 |
basicPortAlarmMasterUpdateFirmwareFileNameThe filename to request when downloading a
new firmware image for the high density alarm
unit attached to this port via TFTP.
Corresponds directly to the UPDATE AMST FIRMWARE
command's FILE parameter.rw DisplayString .1.3.6.1.4.1.33.13.1.17.1.68 |
basicPortAlarmMasterUpdateFirmwareControl to update firmware for the high density alarm unit
attached to the port when set to 'execute'. In response to a
get-request or get-next-request, the agent always
returns 'ready' for this value. Setting the value
to 'ready' has no effect.
The basicPortAlarmMasterUpdateFirmwareHost
and basicPortAlarmMasterUpdateFirmwareFileName must be set
prior to setting this object.
Corresponds directly to the UPDATE AMST FIRMWARE command.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.69 |
basicPortAlarmMasterStatusIndicates the current status of the high density
alarm unit attached to the port. If no response is
obtained from this unit, the status is set to
basicPortAlarmMasterFaultSeverity. Otherwise it is cleared.ro Enumeration .1.3.6.1.4.1.33.13.1.17.1.70 |
basicPortAlarmMasterFaultSeverityControl to determine the severity level associated with the
trap sent out when a fault occurs when no response is
obtained from the high density alarm unit attached to this
port.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.71 |
basicPortPowerMasterControl to configure this port as a power master port.
This control is only valid on those models with variable
configuration ports and which support the power master.
This object can only be set enabled, and doing so will
disable the previous port type, such as basicPortConsolePort.
A set will only update the permanent database. Use a
charPortReset for this change to take effect.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.72 |
basicPortPowerMasterTimeDelayControl to set the power up delay interval in milliseconds for
the power device attached to this port. A response of 'none'
to a get-request or get-next-request may indicate that the
power unit attached to this port is not responding with status.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.73 |
basicPortPowerMasterSwitchControl to power on or off all of the outlets in the power
device attached to this port. A get-request or a get-next-
request always returns ready.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.74 |
basicPortPowerMasterModelThe model number of the power master device, which
is connected to this port. A response of a null string to
a get-request or get-next-request indicates that the power
unit attached to this port is not responding with status.ro DisplayString .1.3.6.1.4.1.33.13.1.17.1.75 |
basicPortPowerMasterSerialNumberThe serial number of the power master device, which
is connected to this port. A response of a null string to
a get-request or get-next-request indicates that the power
unit attached to this port is not responding with status.ro DisplayString .1.3.6.1.4.1.33.13.1.17.1.76 |
basicPortPowerMasterFirmwareThe firmware version of the power master device, which is
connected to this port. A response of a null string to
a get-request or get-next-request indicates that the power
unit attached to this port is not responding with status.ro DisplayString .1.3.6.1.4.1.33.13.1.17.1.77 |
basicPortLockoutControl to prohibit access to this port and send a trap
when login authentication fails.
One must log out the port for this change to take effect.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.78 |
basicPortAsciiToTrapTranslationControl to configure the port as an ascii-to-trap translator.
One must log out the port for this change to take effect.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.79 |
basicPortAsciiToTrapTranslationTrapSeverityControl to determine the severity level associated with the
trap sent out from this port. One must log out the port
for this change to take effect.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.80 |
basicPortAsciiToTrapTranslationMessagesCount of number of trap messages sent from this port.ro Counter .1.3.6.1.4.1.33.13.1.17.1.81 |
basicPortAsciiToTrapTranslationLastMessageThe last message or partial message sent out by this port.ro DisplayString .1.3.6.1.4.1.33.13.1.17.1.82 |
basicPortPowerMasterAlarmSeverityControl to determine the severity level associated with the trap sent out when
the power device is not responding to this port.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.83 |
basicPortPowerMasterDeviceStatusIndicates the current status of the power device controlled by this port. If
the device is responding, the status is cleared. Otherwise the status matches
the basicPortPowerMasterAlarmSeverity.ro Enumeration .1.3.6.1.4.1.33.13.1.17.1.84 |
basicPortBufferingControl to allow data from an attached device to be
retained across multiple sessions. When a session is
established to a port with buffering, the contents of the
command buffer is sent to the remote device.
One must log out the port for this change to take effect.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.85 |
basicPortLogFacilityLevelIndicates that server originated accounting messages
pertaining to this port are logged to the syslog host at
this UNIX facility level. If 'none', the server's
sessionLogFacility is used.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.86 |
basicPortPppDialBackupIndicates whether this port is configured as a PPP dial
backup port. This parameter will not take effect until
the port is logged out, and this function is restricted
to one port.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.87 |
basicPortPppDialBackupNumberThe number to dial when a PPP dial backup link is
activated, which occurs when the network is down and
there are SNMP traps to forward. The port must be
a basicPortPppDialBackup port, and it must be logged
out for the change to take effect.rw DisplayString .1.3.6.1.4.1.33.13.1.17.1.88 |
basicPortPppDialBackupRedialTimerIndicates the time in seconds to wait before redialing the
basicPortPppDialBackupNumber on a basicPortPppDialBackup
port.rw INTEGER ( 30..65535 ) .1.3.6.1.4.1.33.13.1.17.1.89 |
basicPortPppDialBackupRedialRetriesIndicates the number of time to try to dial the backup
number before recording an error, logging out the port,
and if there are new traps trying to dial again.rw INTEGER .1.3.6.1.4.1.33.13.1.17.1.90 |
basicPortPppDialBackupDisconnectTimerIndicates the time in seconds that the dial backup link
will stay up when there is no more SNMP traffic flowing
prior to disconnecting it.rw INTEGER .1.3.6.1.4.1.33.13.1.17.1.91 |
basicPortPppDialBackupLocalAddressThe local address to use in a PPP dial backup link when
the network connection is down and there are SNMP traps
to forward.rw IpAddress .1.3.6.1.4.1.33.13.1.17.1.92 |
basicPortPppDialBackupDestinationAddressThe destination address to use in a PPP dial backup link
when the network connection is down and there are SNMP
traps to forward.rw IpAddress .1.3.6.1.4.1.33.13.1.17.1.93 |
basicPortPppDialBackupAddressesControl to initiate dialing from a dial backup port. In
response to get-request or get-next-request, the agent
always returns 'ready' for this value. Setting the value
to 'ready' has no effect. Setting it to 'execute'
after a valid basicPortPppDialBackupLocalAddress and
basicPortPppDialBackupDestinationAddress are configured
causes the basicPortPppDialBackup port to dial the
basicPortPppDialBackupNumbermber.rw Enumeration .1.3.6.1.4.1.33.13.1.17.1.94 |
basicSerialPortTableA list of basic character serial port entries. SEQUENCE OF BasicSerialPortEntry .1.3.6.1.4.1.33.13.1.18 |
basicSerialPortEntryBasic parameter values for a serial port. BasicSerialPortEntry .1.3.6.1.4.1.33.13.1.18.1 |
basicSerialPortIndexAn index value that uniquely identifies a port.
The port identified by a particular value of this
index is the same port as identified by
charPortIndex in the standard Character MIB.ro INTEGER .1.3.6.1.4.1.33.13.1.18.1.1 |
basicSerialPortBreakAction to take on a BREAK condition from the port.
Corresponds directly to PORT BREAK and the value
labeled 'Break:' in the PORT CHARACTERISTICS
display.rw Enumeration .1.3.6.1.4.1.33.13.1.18.1.2 |
basicSerialPortInterruptsControl for recognizing BREAK or local switch to
interrupt a session. Corresponds directly to PORT
INTERRUPTS and the presence of the label
'Interrupts' following the label 'Enabled
Characteristics:' in the PORT CHARACTERISTICS
display.rw Enumeration .1.3.6.1.4.1.33.13.1.18.1.3 |
basicSerialPortNoLossControl for storing port input locally in
anticipation of session startup. Corresponds
directly to PORT NOLOSS and the presence of the
label 'Noloss' following the label 'Enabled
Characteristics:' in the PORT CHARACTERISTICS
display.rw Enumeration .1.3.6.1.4.1.33.13.1.18.1.4 |
basicSerialPortPauseControl for pausing after each screenful of
locally-originated output to the port. Corresponds
directly to PORT PAUSE and the presence of the label
'Pause' following the label 'Enabled
Characteristics:' in the PORT CHARACTERISTICS
display.rw Enumeration .1.3.6.1.4.1.33.13.1.18.1.5 |
basicSerialPortPromptPrompt for the system to use on the port.
Corresponds directly to PORT PROMPT and the value
labeled 'Prompt:' in the PORT ALTERNATE
CHARACTERISTICS display.rw DisplayString .1.3.6.1.4.1.33.13.1.18.1.6 |
basicSerialPortTerminalTypeType of terminal attached to the port, for
formatting local output. Corresponds directly to
PORT TYPE and the value labeled 'Type:' in the PORT
CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.13.1.18.1.7 |
basicSerialPortTypeaheadLimitMaximum number of input characters to hold pending
tranmission on a session. Corresponds directly to
PORT TYPEAHEAD SIZE and the value labeled 'Typeahead
Size:' in the PORT ALTERNATE CHARACTERISTICS
display.rw INTEGER .1.3.6.1.4.1.33.13.1.18.1.8 |
basicSerialPortBackwardSwitchCharacter input from the character port to cause a
switch to the previous, lower numbered session. The
value 0 indicates no character has this effect.
Corresponds directly to PORT BACKWARD SWITCH and the
value labeled 'Backwards Switch:' in the PORT
CHARACTERISTICS display.rw INTEGER .1.3.6.1.4.1.33.13.1.18.1.9 |
basicSerialPortForwardSwitchCharacter input from the character port to cause a
switch to the next, higher numbered session. The
value 0 indicates no character has this effect.
Corresponds directly to PORT FORWARD SWITCH and the
value labeled 'Forwards Switch:' in the PORT
CHARACTERISTICS display.rw INTEGER .1.3.6.1.4.1.33.13.1.18.1.10 |
basicSerialPortLocalSwitchCharacter input from the character port to cause a
switch to local command mode. The value 0 indicates
no character has this effect. Corresponds directly
to PORT LOCAL SWITCH and the value labeled 'Local
Switch:' in the PORT CHARACTERISTICS display.rw INTEGER .1.3.6.1.4.1.33.13.1.18.1.11 |
basicSerialPortModemControlControl for observing hardware modem control
signals. Corresponds directly to PORT MODEM CONTROL
and the value labeled 'Modem Control:' in the PORT
CHARACTERISTICS display. This object is not available
on units that do not support modem signals (ie 2220).rw Enumeration .1.3.6.1.4.1.33.13.1.18.1.12 |
basicSerialPortSignalCheckControl for observing DSR and DCD to bound allowing
sessions. Corresponds directly to PORT SIGNAL CHECK
and the presence of the label 'Signal Check'
following the label 'Enabled Characteristics:' in
the PORT CHARACTERISTICS display. This object is not
available on units that do not support modem signals
(ie 2220).rw Enumeration .1.3.6.1.4.1.33.13.1.18.1.13 |
basicSerialPortDSRLogoutControl for logging out the port when DCD is
deasserted. Corresponds directly to PORT DSRLOGOUT
and the presence of the label 'DSRlogout' following
the label 'Enabled Characteristics:' in the PORT
CHARACTERISTICS display. This object is not available
on units that do not support modem signals (ie 2220).rw Enumeration .1.3.6.1.4.1.33.13.1.18.1.14 |
basicSerialPortDSRObserveControl for beginning the login sequence on the
port when DCD is asserted. Corresponds directly to
PORT DSRWAIT and the presence of the label 'DSRwait'
following the label 'Enabled Characteristics:' in
the PORT CHARACTERISTICS display. This object is not
available on units that do not support modem signals
(ie 2220).rw Enumeration .1.3.6.1.4.1.33.13.1.18.1.15 |
basicSerialPortDCDTimeoutThe number of milleseconds that DCD may be asserted
before disconnecting the port. Corresponds directly
to PORT DCD TIMEOUT and the value labeled 'DCD
Timeout:' in the PORT ALTERNATE CHARACTERISTICS
display. This object is not available
on units that do not support modem signals (ie 2220).rw INTEGER .1.3.6.1.4.1.33.13.1.18.1.16 |
basicSerialPortDTRAssertControl when the system asserts DTR on the port.
always unconditional(DISABLED)
onConnectionOrRing connection formed or RING
asserted(ENABLED)
onConnection connection formed
(FORCONNECTION)
onRing RING asserted (FORRING)
Corresponds directly to PORT DTRWAIT and the value
labeled 'DTR Wait:' in the PORT ALTERNATE
CHARACTERISTICS display. This object is not available
on units that do not support modem signals (ie 2220).rw Enumeration .1.3.6.1.4.1.33.13.1.18.1.17 |
basicSerialPortLimitedCommandsControl for limiting the commands available to the
user on the port. Corresponds directly to PORT
SECURITY and the presence of the label 'Security'
following the label 'Enabled Characteristics:' in
the PORT CHARACTERISTICS display. This object is not
available on units that do not support modem signals
(ie 2220).rw Enumeration .1.3.6.1.4.1.33.13.1.18.1.18 |
basicSerialPortLimitedViewControl for restricting what a user may display.
Corresponds directly to PORT LIMITED VIEW and the
presence of the label 'Limited View' following the
label 'Enabled Characteristics:' in the PORT
CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.13.1.18.1.19 |
basicSerialPortPasswordControl for requiring the user to supply the login
password to log in on the port. Corresponds
directly to PORT PASSWORD and the presence of the
label 'Password' following the label 'Enabled
Characteristics:' in the PORT CHARACTERISTICS
display.rw Enumeration .1.3.6.1.4.1.33.13.1.18.1.20 |
basicSerialPortLineEditorControl for allowing the user to use local mode
command line editing. Corresponds directly to PORT
LINE EDITOR and the presence of the label 'Line
Editor' following the label 'Enabled
Characteristics:' in the PORT CHARACTERISTICS
display.rw Enumeration .1.3.6.1.4.1.33.13.1.18.1.21 |
basicSerialPortLineEditorBackspaceCharacter input from the character port to move the
cursor to the left. The value 0 indicates no
character has this effect. Corresponds directly to
PORT LINE EDITOR BACKSPACE and the value labeled
'Backspace Character:' in the PORT ALTERNATE
CHARACTERISTICS display.rw INTEGER .1.3.6.1.4.1.33.13.1.18.1.22 |
basicSerialPortLineEditorBeginningCharacter input from the character port to move the
cursor to the beginning of the line. The value 0
indicates no character has this effect. Corresponds
directly to PORT LINE EDITOR BEGINNING and the value
labeled 'Begin Line Character:' in the PORT
ALTERNATE CHARACTERISTICS display.rw INTEGER .1.3.6.1.4.1.33.13.1.18.1.23 |
basicSerialPortLineEditorCancelCharacter input from the character port to cancel
an interactive dialog or delete the current line.
The value 0 indicates no character has this effect.
Corresponds directly to PORT LINE EDITOR CANCEL and
the value labeled 'Cancel Character:' in the PORT
ALTERNATE CHARACTERISTICS display.rw INTEGER .1.3.6.1.4.1.33.13.1.18.1.24 |
basicSerialPortLineEditorDeleteBeginningCharacter input from the character port to delete
the current line from the cursor to the beginning.
The value 0 indicates no character has this effect.
Corresponds directly to PORT LINE EDITOR DELETE
BEGINNING and the value labeled 'Delete Begin
Character:' in the PORT ALTERNATE CHARACTERISTICS
display.rw INTEGER .1.3.6.1.4.1.33.13.1.18.1.25 |
basicSerialPortLineEditorDeleteLineCharacter input from the character port to delete
the current line. The value 0 indicates no
character has this effect. Corresponds directly to
PORT LINE EDITOR DELETE LINE and the value labeled
'Delete Line Character:' in the PORT ALTERNATE
CHARACTERISTICS display.rw INTEGER .1.3.6.1.4.1.33.13.1.18.1.26 |
basicSerialPortLineEditorEndCharacter input from the character port to move the
cursor to the end of the line. The value 0
indicates no character has this effect. Corresponds
directly to PORT LINE EDITOR END and the value
labeled 'End of Line Character:' in the PORT
ALTERNATE CHARACTERISTICS display.rw INTEGER .1.3.6.1.4.1.33.13.1.18.1.27 |
basicSerialPortLineEditorForwardCharacter input from the character port to move the
cursor to the right. The value 0 indicates no
character has this effect. Corresponds directly to
PORT LINE EDITOR FORWARDS and the value labeled
'Forwards Character:' in the PORT ALTERNATE
CHARACTERISTICS display.rw INTEGER .1.3.6.1.4.1.33.13.1.18.1.28 |
basicSerialPortLineEditorInsertToggleCharacter input from the character port to toggle
between insert and overwrite modes. The value 0
indicates no character has this effect. Corresponds
directly to PORT LINE EDITOR INSERT TOGGLE and the
value labeled 'Insert Character:' in the PORT
ALTERNATE CHARACTERISTICS display.rw INTEGER .1.3.6.1.4.1.33.13.1.18.1.29 |
basicSerialPortLineEditorNextLineCharacter input from the character port to recall
the next, newer line in the command history. The
value -1 indicates no character has this effect.
Corresponds directly to PORT LINE EDITOR NEXT LINE
and the value labeled 'Next Line Character:' in the
PORT ALTERNATE CHARACTERISTICS display.rw INTEGER .1.3.6.1.4.1.33.13.1.18.1.30 |
basicSerialPortLineEditorPreviousLineCharacter input from the character port to recall
the previous, older line in the command history.
The value 0 indicates no character has this effect.
Corresponds directly to PORT LINE EDITOR PREVIOUS
LINE and the value labeled 'Previous Line
Character:' in the PORT ALTERNATE CHARACTERISTICS
display.rw INTEGER .1.3.6.1.4.1.33.13.1.18.1.31 |
basicSerialPortLineEditorQuotingCharacterCharacter input from the character port to inhibit
interpretation of the next input character. The
value 0 indicates no character has this effect.
Corresponds directly to PORT LINE EDITOR QUOTING
CHARACTER and the value labeled 'Quoting Character:'
in the PORT ALTERNATE CHARACTERISTICS display.rw INTEGER .1.3.6.1.4.1.33.13.1.18.1.32 |
basicSerialPortLineEditorRedisplayCharacter input from the character port to
redisplay the current command line. The value 0
indicates no character has this effect. Corresponds
directly to PORT LINE EDITOR REDISPLAY CHARACTER and
the value labeled 'Redisplay Character:' in the PORT
ALTERNATE CHARACTERISTICS display.rw INTEGER .1.3.6.1.4.1.33.13.1.18.1.33 |
basicSerialPortQuadartReceiveDiscardControl for discard of received errors from quadart
hardware.rw Enumeration .1.3.6.1.4.1.33.13.1.18.1.34 |
basicSerialPortAPDProtocolsA bit map that specifies the protocols
that this port will attempt to detect
using the Auto Protocol Detection
function. The bit numbers for the
protocols are: 1;ARAP, 3;Interactive, 4;SLIP, 5;PPP.
Bits 6-16 are reserved for future use.
More than one of these protocols may
be ORed together. The default is 0 (zero)
no protocols.rw OCTET STRING .1.3.6.1.4.1.33.13.1.18.1.35 |
basicSerialPortAPDTimeoutA time value, in seconds, that
specifies how long the port will
attempt to determine which
protocol is coming into the port.
When basicSerialPortAPDTimeout seconds
have expired, the port will assume the
protocol to use is that specified by
basicSerialPortAPDDefaultProtocol.
A value of 0 (zero provides an unlimited timeout.rw INTEGER .1.3.6.1.4.1.33.13.1.18.1.36 |
basicSerialPortAPDDefaultProtocolA bit map that specifies the protocol
that this port will use when the time
specified by basicSerialPortAPDTimeout
has expired without sucessfully
identifying the incoming porotocol.
The bit numbers for the protocols are:
None;Logout the port, 1;ARAP, 2;CSLIP,
3;Interactive, 4;SLIP, 5;PPP. Bits 6-16
are reserved for future use. Only
one protocol may be specified for this
objectrw OCTET STRING .1.3.6.1.4.1.33.13.1.18.1.37 |
basicSerialPortUsernameCharSetA control, that if set to seven-bit, will
allow only the ASCII printable characters
in the range SP (X20) to ~ (X7E) in the username
field. A value of none allows any characterrw Enumeration .1.3.6.1.4.1.33.13.1.18.1.38 |
basicSerialPortAutoHangupA control that, if enabled, will cause the port to be
logged off when the last session on that port is destroyedrw Enumeration .1.3.6.1.4.1.33.13.1.18.1.39 |
basicSerialPortCommandSizeMaximum number of input characters to hold in the command
buffer. Corresponds directly to the PORT COMMAND SIZE
and the value labeled 'Command Size:' in the PORT
ALTERNATE CHARACTERISTICS display.rw INTEGER .1.3.6.1.4.1.33.13.1.18.1.40 |
basicSerialPortAutoProtocolDetectPromptControls whether to send the basicAutoProtocolDetectMessage
out the serial port at the beginning of auto protocol
detection mode. Corresponds to the value labeled 'APD
Prompt' in the PORT ALTERNATE CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.13.1.18.1.41 |
basicSerialPortUsernamePromptThe text string used to prompt for a user's name.
Corresponds directly to the value labeled 'Username
Prompt:' in the PORT ALTERNATE CHARACTERISTICS display.rw DisplayString .1.3.6.1.4.1.33.13.1.18.1.42 |
basicSerialPortPasswordPromptThe text string used to prompt for a user's password.
Corresponds directly to the value labeled 'Password
Prompt:' in the PORT ALTERNATE CHARACTERISTICS display.rw DisplayString .1.3.6.1.4.1.33.13.1.18.1.43 |
basicSerialPortAutoProtocolDetectSecurityInteractiveOnlyControls whether Auto Protocol Detect (APD) authentication
applies only to interactive users, and not to other APD
protocols such as PPP. Corresponds directly to the value
labeled 'APD Authentication Interactive Only:' in the PORT
CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.13.1.18.1.44 |
basicSerialPortDedicatedUserDataThe text string to send at the beginning of a connection
to a Telnet dedicated service. Corresponds to the value
labeled 'UserData:' in the PORT CHARACTERISTICS display.rw DisplayString .1.3.6.1.4.1.33.13.1.18.1.45 |
basicSerialPortIpAutoDiscoveryControl to enable a non-standard method of acquiring the
IP address after boot completes via the BOOTP protocol.
Corresponds to the value labeled 'IP Address
Auto Discovery' in the SERVER CHARACTERISTICS display.rwdeprecated Enumeration .1.3.6.1.4.1.33.13.1.18.1.47 |
basicSerialPortDedicatedKickStartDataA text string which is used to compare at login time to
incoming serial data. A match will initiate a telnet
session to a dedicated service. Corresponds to the value
labeled 'KickStart:' in the PORT CHARACTERISTICS display.rw DisplayString .1.3.6.1.4.1.33.13.1.18.1.48 |
basicSerialPortBreakLengthSpecifies the duration in milliseconds of a remote serial
break which is sent via the Telnet Break command.
Corresponds directly to the value labeled 'Break Length:'
in the PORT CHARACTERISTIC display.rw Enumeration .1.3.6.1.4.1.33.13.1.18.1.50 |
basicSerialPortRotaryRoundRobinControls whether a port which participates in an internet
rotary is selected in round robin or fixed priority order.
Corresponds directly to the value labeled 'Round Robin
search:' in the SERVER INTERNET ROTARY display.rw Enumeration .1.3.6.1.4.1.33.13.1.18.1.51 |
basicSerialPortWelcomeBeforeAuthenticationControl to display the basicWelcome message prior to
authenticating the user. Corresponds to the presence of the
value 'Welcome-Banner-Pre-Authentication' following the
label 'Enabled Characteristics' in the PORT CHARACTERISTICS
display.rw Enumeration .1.3.6.1.4.1.33.13.1.18.1.52 |
basicSerialPortGatewayAutoDiscoveryControl to enable a non-standard method of acquiring the
gateway address after boot completes via the bootp
protocol.rwdeprecated Enumeration .1.3.6.1.4.1.33.13.1.18.1.53 |
basicSerialPortSubnetAutoDiscoveryControl to enable a non-standard method of acquiring the
subnet mask after boot completes via the bootp protocol.rwdeprecated Enumeration .1.3.6.1.4.1.33.13.1.18.1.54 |
basicSerialPortRaiseLowerDtrA control to to raise or lower the DTR signal from this
port by setting it to high or low, respectively. This
request will have no effect unless
basicSerialPortRaiseControlDtr is enabled. In response
to a get-request or get-next-request the agent always
returns low for this object.rw Enumeration .1.3.6.1.4.1.33.13.1.18.1.55 |
basicSerialPortRaiseControlDtrControls the ability to change the state of DTR using
basicSerialPortRaiseLowerDTR. This characteristic is not
intended for use with modem ports. Corresponds directly
to the presence of 'Control DTR' under the label
'Enabled Characteristics' in the PORT CHARACTERISTICS
display. The desired change will not take effect until
the port is logged off.rw Enumeration .1.3.6.1.4.1.33.13.1.18.1.56 |
basicSerialPortIpConfigureBootpControl to use the BOOTP protocol upon startup to learn
the unit's own internet address, subnet mask, primary and
secondary gateway servers, domain name servers, time
server and domain name. This object was moved to the
MRV-IN-REACH-INTERNET-MIB for InReach agent software version V2.4.rwdeprecated Enumeration .1.3.6.1.4.1.33.13.1.18.1.57 |
basicConsoleLogoutDisconnectControl for automatic session disconnection when a
console port user logs out. Corresponds directly to
SERVER CONSOLE LOGOUT and the presence of the label
'Console Logout' following the label 'Enabled
Characteristics:' in the SERVER CHARACTERISTICS
display.rw Enumeration .1.3.6.1.4.1.33.13.1.19 |
basicControlledPortsStatus of Controlled Ports feature. Corresponds directly
to the 'Controlled Ports' following the label 'Enabled
Characteristics:' in the SERVER CHARACTERISTICS display.
Enabling this feature causes strings of control characters
to be sent out on a port upon starting and/or stopping a sessionrw Enumeration .1.3.6.1.4.1.33.13.1.20 |
basicPortSessionTableA list of port session entries. SEQUENCE OF BasicPortSessEntry .1.3.6.1.4.1.33.13.1.21 |
basicPortSessEntryStatus and parameter values for a basic port
session. BasicPortSessEntry .1.3.6.1.4.1.33.13.1.21.1 |
basicPortPortIndexThe value of basicPortIndex for the port to which
this session belongs.
The port identified by a particular value of this
index is the same port as identified by
charPortIndex in the standard Character MIB.ro INTEGER .1.3.6.1.4.1.33.13.1.21.1.1 |
basicPortSessIndexThe session index in the context of the port, a
non-zero positive integer. Session indexes within a
port need not be sequential. Session indexes may be
reused for different ports. For example, port 1 and
port 3 may both have a session 2 at the same time.
Session indexes may have any valid integer value,
with any meaning convenient to the agent
implementation.
The session identified by a particular value of this
index is the same session as identified by
charSessIndex in the standard Character MIB.ro INTEGER .1.3.6.1.4.1.33.13.1.21.1.2 |
basicSessControlledA control to send preconfigured controlled port session
strings out the serial port when entering or exiting
this session. Corresponds directly to the value labeled
'Controlled' under the Service Mode header in the
SESSION display.ro Enumeration .1.3.6.1.4.1.33.13.1.21.1.3 |
basicPortSessEncryptionStatus of the default encryption value to be set
for each session. Corresponds directly to Console
Security on SHOW SERVER screen.rw Enumeration .1.3.6.1.4.1.33.13.1.22 |
basicTemperatureUnitsIndicates the units of measurement for the temperature sensors.rw Enumeration .1.3.6.1.4.1.33.13.1.23 |
basicEnvironmentalManagerCircuitBreakerIndicates whether the circuit breaker is activated.ro Enumeration .1.3.6.1.4.1.33.13.1.24 |
basicContactClosureOrAlarmInputTableInformation about contact closures or alarm inputs. SEQUENCE OF BasicContactClosureOrAlarmInputEntry .1.3.6.1.4.1.33.13.1.25 |
basicContactClosureOrAlarmInputEntryAn entry in the basicContactClosureOrAlarmInputTable. BasicContactClosureOrAlarmInputEntry .1.3.6.1.4.1.33.13.1.25.1 |
basicContactClosureOrAlarmInputValueIndicates the state of the contact closure or alarm input.ro Enumeration .1.3.6.1.4.1.33.13.1.25.1.1 |
basicContactClosureOrAlarmInputNameThe name used to identify this contact closure or alarm input.rw DisplayString .1.3.6.1.4.1.33.13.1.25.1.2 |
basicContactClosureOrAlarmInputTrapEnableControl to send trap when contact closure or alarm input changes
state.rw Enumeration .1.3.6.1.4.1.33.13.1.25.1.3 |
basicContactClosureOrAlarmInputFaultSeverityControl to determine the severity level associated with the
trap sent out when a fault occurs for a given contact
closure or alarm input.rw Enumeration .1.3.6.1.4.1.33.13.1.25.1.4 |
basicContactClosureOrAlarmInputFaultStateControl to indicate which state, open or closed, represents the
fault condition. The other state is the cleared condition.rw Enumeration .1.3.6.1.4.1.33.13.1.25.1.5 |
basicContactClosureOrAlarmInputStatusIndicates the current status of the contact closure or alarm input.
If the basicContactClosureOrAlarmInputValue matches the fault
state, then the status is equal to the fault severity. Otherwise
the status is cleared.ro Enumeration .1.3.6.1.4.1.33.13.1.25.1.6 |
basicContactClosureOrAlarmInputZoneThe name used to identify the zone where the equipment
resides.rw DisplayString .1.3.6.1.4.1.33.13.1.25.1.7 |
basicContactClosureOrAlarmInputRelatedEquipmentThe name used to identify related equipment.rw DisplayString .1.3.6.1.4.1.33.13.1.25.1.8 |
basicContactClosureOrAlarmInputSiteIdThe name used to identify the site where the unit resides.rw DisplayString .1.3.6.1.4.1.33.13.1.25.1.9 |
basicContactClosureOrAlarmInputIndexAn index which uniquely identifies the contact closure or alarm
input.ro INTEGER .1.3.6.1.4.1.33.13.1.25.1.10 |
basicContactClosureOrAlarmInputManufacturerThe name used to identify the manufacturer of this equipment.rw DisplayString .1.3.6.1.4.1.33.13.1.25.1.11 |
basicContactClosureOrAlarmInputModelThe model name of this equipment.rw DisplayString .1.3.6.1.4.1.33.13.1.25.1.12 |
basicPowerOutletTableInformation about Environmental Manager Power Outlets. SEQUENCE OF BasicPowerOutletEntry .1.3.6.1.4.1.33.13.1.26 |
basicPowerOutletEntryAn entry in the basicPowerOutletTable. BasicPowerOutletEntry .1.3.6.1.4.1.33.13.1.26.1 |
basicPowerOutletOnOffControls turning on or off the power for the device connected to
this power outlet.rw Enumeration .1.3.6.1.4.1.33.13.1.26.1.1 |
basicPowerOutletRebootControls rebooting of the device attached this power outlet.rw INTEGER .1.3.6.1.4.1.33.13.1.26.1.2 |
basicPowerOutletNameA name used to identify this power outlet.rw DisplayString .1.3.6.1.4.1.33.13.1.26.1.3 |
basicPowerOutletRedundantControls whether power outlets in bank A have redundant outlets
in bank B. When enabled, powering on an outlet in bank A will
simultaneously power on the corresponding outlet number in bank
B.ro Enumeration .1.3.6.1.4.1.33.13.1.26.1.4 |
basicPowerOutletConsoleNameA name used to identify a console port on a unit with power outlet
managment.rw DisplayString .1.3.6.1.4.1.33.13.1.26.1.5 |
basicPowerOutletHighCurrentA control to indicate a high current unit is attached to this
power outlet. When enabled the high current unit will provide current
when it detects no power from the power outlet; and will stop the
current when the outlet resumes power. This control only works on
those InReach devices which support the high current unit such as
the IRMGR0. Corresponds directly to the value labeled 'HCNC Setting'
in the INREACH MANAGER OUTLET STATUS display.rw Enumeration .1.3.6.1.4.1.33.13.1.26.1.6 |
basicPowerOutletIndexAn index which uniquely identifies a power outlet.ro INTEGER .1.3.6.1.4.1.33.13.1.26.1.10 |
basicTemperatureHumiditySensor OBJECT IDENTIFIER .1.3.6.1.4.1.33.13.1.27 |
basicTemperatureSensorTableInformation about Environmental Manager Temperature Sensors. SEQUENCE OF BasicTemperatureSensorEntry .1.3.6.1.4.1.33.13.1.27.1 |
basicTemperatureSensorEntryAn entry in the basicTemperatureSensorTable. BasicTemperatureSensorEntry .1.3.6.1.4.1.33.13.1.27.1.1 |
basicTempTrapHighThresholdThe temperature at or above which a sensorThresholdTrap is
generated.rw INTEGER .1.3.6.1.4.1.33.13.1.27.1.1.1 |
basicTempTrapLowThresholdThe temperature at or below which a sensorThresholdTrap is
generated.rw INTEGER .1.3.6.1.4.1.33.13.1.27.1.1.2 |
basicTemperatureSensorControls the enabling or disabling of a temperature sensor.rw Enumeration .1.3.6.1.4.1.33.13.1.27.1.1.3 |
basicTemperatureValueThe current temperature reading for this sensor.rw INTEGER .1.3.6.1.4.1.33.13.1.27.1.1.4 |
basicTemperatureAlarmSeverityControl to determine the severity level associated with the
trap sent out when the temperature reading is out-of-bounds.rw Enumeration .1.3.6.1.4.1.33.13.1.27.1.1.5 |
basicTemperatureAlarmStatusIndicates the current status of the temperature sensor.
If the basicTemperatureValue falls within the normal range,
the status is cleared. Otherwise the status matches the alarm
severity level.ro Enumeration .1.3.6.1.4.1.33.13.1.27.1.1.6 |
basicTemperatureHumiditySensorNameThe name used to identify this temperature sensor.rw DisplayString .1.3.6.1.4.1.33.13.1.27.1.1.7 |
basicTemperatureSensorIndexAn index which uniquely identifies a temperature sensor.ro INTEGER .1.3.6.1.4.1.33.13.1.27.1.1.10 |
basicHumiditySensorTableInformation about Environmental Manager Humidity Sensors. SEQUENCE OF BasicHumiditySensorEntry .1.3.6.1.4.1.33.13.1.27.2 |
basicHumiditySensorEntryAn entry in the basicHumiditySensorTable. BasicHumiditySensorEntry .1.3.6.1.4.1.33.13.1.27.2.1 |
basicHumidityTrapHighThresholdThe humidity at or above which a sensorThresholdTrap is generated.rw INTEGER .1.3.6.1.4.1.33.13.1.27.2.1.1 |
basicHumidityTrapLowThresholdThe humidity at or below which a sensorThresholdTrap is generated.rw INTEGER .1.3.6.1.4.1.33.13.1.27.2.1.2 |
basicHumiditySensorControls the enabling or disabling of a humidity sensor.rw Enumeration .1.3.6.1.4.1.33.13.1.27.2.1.3 |
basicHumidityValueThe current humidity reading for this sensor.rw INTEGER .1.3.6.1.4.1.33.13.1.27.2.1.4 |
basicHumidityAlarmSeverityControl to indicate the severity level associated with the
trap sent out when the humidity reading is out-of-bounds.rw Enumeration .1.3.6.1.4.1.33.13.1.27.2.1.5 |
basicHumidityAlarmStatusIndicates the current status of the humidity sensor.
If the basicHumidityValue falls within the normal range,
the status is cleared. Otherwise the status matches the alarm
severity level.ro Enumeration .1.3.6.1.4.1.33.13.1.27.2.1.6 |
basicHumiditySensorIndexAn index which uniquely identifies a humidity sensor.ro INTEGER .1.3.6.1.4.1.33.13.1.27.2.1.10 |
basicControlSignalTableInformation about Environmental Manager Control Signal points. SEQUENCE OF BasicControlSignalEntry .1.3.6.1.4.1.33.13.1.28 |
basicControlSignalEntryAn entry in the basicControlSignalTable. BasicControlSignalEntry .1.3.6.1.4.1.33.13.1.28.1 |
basicControlSignalValueSets and reads the state of the control signal point.rw Enumeration .1.3.6.1.4.1.33.13.1.28.1.1 |
basicControlSignalIndexAn index which uniquely identifies a control signal point.ro INTEGER .1.3.6.1.4.1.33.13.1.28.1.10 |
basicPowerAlarmTimerThe polling interval in seconds for the fuse and power supply
status. An alarm trap is issued on power failure.rw INTEGER .1.3.6.1.4.1.33.13.1.29 |
basicControlOutputTableInformation about controlled output distribution points. SEQUENCE OF BasicControlOutputEntry .1.3.6.1.4.1.33.13.1.30 |
basicControlOutputEntryAn entry in the basicControlOutputTable. BasicControlOutputEntry .1.3.6.1.4.1.33.13.1.30.1 |
basicControlOutputSignalDtrRtsControls the raising or lowering of a signal on a distribution
control signal point. The signal is DTR when the
basicControlOutputIndex is odd, or RTS when the
basicControlOutputIndex is even.rw Enumeration .1.3.6.1.4.1.33.13.1.30.1.1 |
basicControlOutputNameThe name used to identify this distribution control signal point.rw DisplayString .1.3.6.1.4.1.33.13.1.30.1.2 |
basicControlOutputIndexAn index which uniquely identifies a distribution control
signal point.ro INTEGER .1.3.6.1.4.1.33.13.1.30.1.10 |
basicPowerStatusFuseAIndicates the status of fuse bank A.ro Enumeration .1.3.6.1.4.1.33.13.1.31 |
basicPowerStatusFuseBIndicates the status of fuse bank B.ro Enumeration .1.3.6.1.4.1.33.13.1.32 |
basicPowerSupplyStatusAIndicates the status of power supply A.ro Enumeration .1.3.6.1.4.1.33.13.1.33 |
basicPowerSupplyStatusBIndicates the status of power supply B.ro Enumeration .1.3.6.1.4.1.33.13.1.34 |
basicPortTrapTableA list of traps associated with signal control changes on ports. SEQUENCE OF BasicPortTrapEntry .1.3.6.1.4.1.33.13.1.35 |
basicPortTrapEntryAdministrative status of signal change traps for a hardware port. BasicPortTrapEntry .1.3.6.1.4.1.33.13.1.35.1 |
basicPortTrapIndexAn index value that uniquely identifies a port.
The port identified by a particular value of this
index is the same port as identified by rs232PortIndex
in the standard rs232 MIB.ro INTEGER .1.3.6.1.4.1.33.13.1.35.1.1 |
basicPortSignalNameIdentification of the hardware signal as specified in RFC1659
as follows:
rts Request to Send
cts Clear to Send
dsr Data Set Ready
dts Data Terminal Ready
ri Ring Indicator
dcd Received Line Signal Detector
Some agents do not support DSR since its pin is shared with DCD.ro Enumeration .1.3.6.1.4.1.33.13.1.35.1.2 |
basicPortTrapStatusControl to toggle the sending of a trap on a specific signal
change on a physical port. One must logout the port prior to this
taking effect.rw Enumeration .1.3.6.1.4.1.33.13.1.35.1.3 |
basicAlarmMasterInputTableInformation about the high density alarm manager's alarm inputs. SEQUENCE OF BasicAlarmMasterInputEntry .1.3.6.1.4.1.33.13.1.36 |
basicAlarmMasterInputEntryAn entry in the basicAlarmMasterInputTable. BasicAlarmMasterInputEntry .1.3.6.1.4.1.33.13.1.36.1 |
basicAlarmMasterInputPortAn index value that uniquely identifies a port.
The port identified by a particular value of this
index is the same port as identified by
charPortIndex in the standard Character MIB.ro INTEGER .1.3.6.1.4.1.33.13.1.36.1.1 |
basicAlarmMasterInputSlotAn index value that uniquely identifies a slot of
alarm points on a given high density alarm port.ro INTEGER .1.3.6.1.4.1.33.13.1.36.1.2 |
basicAlarmMasterInputPointAn index value that uniquely identifies an alarm
point within an alarm slot on a high density
alarm port.ro INTEGER .1.3.6.1.4.1.33.13.1.36.1.3 |
basicAlarmMasterInputNameThe name used to identify this alarm point.rw DisplayString .1.3.6.1.4.1.33.13.1.36.1.4 |
basicAlarmMasterInputTrapEnableControl to send a trap when the alarm input changes state.rw Enumeration .1.3.6.1.4.1.33.13.1.36.1.5 |
basicAlarmMasterControlOutputSignalControl to toggle the output signal for an alarm point.rw Enumeration .1.3.6.1.4.1.33.13.1.36.1.6 |
basicAlarmMasterInputEnableControl to toggle whether this alarm point is active.rw Enumeration .1.3.6.1.4.1.33.13.1.36.1.7 |
basicAlarmMasterInputDebounceIntervalAmount of time in seconds to debounce a signal change before
triggering an alarm.rw INTEGER ( 0..30 ) .1.3.6.1.4.1.33.13.1.36.1.8 |
basicAlarmMasterInputFaultSeverityControl to determine the severity level associated with the
trap sent out when a fault occurs for this alarm input point.rw Enumeration .1.3.6.1.4.1.33.13.1.36.1.9 |
basicAlarmMasterInputFaultStateControl to indicate which state, open or closed, represents the
fault condition for this alarm input point. The other state is
the cleared condition.rw Enumeration .1.3.6.1.4.1.33.13.1.36.1.10 |
basicAlarmMasterInputStatusIndicates the current status of the alarm input point.
If the basicAlarmMasterInputValue matches the fault
state, then the status is equal to the fault severity. Otherwise
the status is cleared.ro Enumeration .1.3.6.1.4.1.33.13.1.36.1.11 |
basicAlarmMasterInputValueIndicates the current state of the alarm input point.ro Enumeration .1.3.6.1.4.1.33.13.1.36.1.12 |
basicAlarmMasterDisplayControl to toggle the display of the alarm status for this point
in the display window of the high density alarm unit.rw Enumeration .1.3.6.1.4.1.33.13.1.36.1.13 |
basicAlarmMasterInputZoneThe name used to identify the zone where the equipment
resides.rw DisplayString .1.3.6.1.4.1.33.13.1.36.1.14 |
basicAlarmMasterInputRelatedEquipmentThe name used to identify related equipment.rw DisplayString .1.3.6.1.4.1.33.13.1.36.1.15 |
basicAlarmMasterInputSiteIdThe name used to identify the site where the unit resides.rw DisplayString .1.3.6.1.4.1.33.13.1.36.1.16 |
basicAlarmMasterInputManufacturerThe name used to identify the manufacturer of this equipment.rw DisplayString .1.3.6.1.4.1.33.13.1.36.1.17 |
basicAlarmMasterInputModelThe model name of this equipment.rw DisplayString .1.3.6.1.4.1.33.13.1.36.1.18 |
basicPowerMasterOutletTableInformation about power master outlets. SEQUENCE OF BasicPowerMasterOutletEntry .1.3.6.1.4.1.33.13.1.37 |
basicPowerMasterOutletEntryAn entry in the basicPowerMasterOutletTable. BasicPowerMasterOutletEntry .1.3.6.1.4.1.33.13.1.37.1 |
basicPowerMasterPortIndexAn index value that uniquely identifies a port.
The port identified by a particular value of this
index is the same port as identified by the
charPortIndex in the standard Character MIB.ro INTEGER .1.3.6.1.4.1.33.13.1.37.1.1 |
basicPowerMasterOutletIndexAn index which uniquely identifies a power master outlet.ro INTEGER .1.3.6.1.4.1.33.13.1.37.1.2 |
basicPowerMasterOutletNameThe name used to identify this power master outlet.rw DisplayString .1.3.6.1.4.1.33.13.1.37.1.3 |
basicPowerMasterOutletStateSwitches the power master outlet on or off. There may be a
noticeable time delay while processing a get-request for this
object. A response of 'off' to a get-request may indicate that
the state is temporarily unavailable.rw Enumeration .1.3.6.1.4.1.33.13.1.37.1.4 |
basicPowerMasterOutletAmperageStatusIndicates the current amperage drawn at this outlet. There may
be a noticeable time delay while processing a get-request for
this object. A null string indicates that amperage status is
temporarily unavailable.ro DisplayString .1.3.6.1.4.1.33.13.1.37.1.5 |
basicControlOutputRelayTableInformation about controlled output relays. SEQUENCE OF BasicControlOutputRelayEntry .1.3.6.1.4.1.33.13.1.38 |
basicControlOutputRelayEntryAn entry in the basicControlOutputRelayTable. BasicControlOutputRelayEntry .1.3.6.1.4.1.33.13.1.38.1 |
basicControlOutputRelayIndexAn index which uniquely identifies a control output relay.ro INTEGER .1.3.6.1.4.1.33.13.1.38.1.1 |
basicControlOutputRelayNameThe name used to identify this control output relay.rw DisplayString .1.3.6.1.4.1.33.13.1.38.1.2 |
basicControlOutputRelayStateControls the opening or closing of the control output relay.rw Enumeration .1.3.6.1.4.1.33.13.1.38.1.3 |
basicControlOutputRelayStatusIndicates the current status of the control output relay.ro Enumeration .1.3.6.1.4.1.33.13.1.38.1.4 |
basicAutoProtocolDetectMessageThe text string sent as a prompt message out the
port at the beginning of auto protocol detection mode.
Corresponds to the value labeled 'APD Message' in the
SERVER UNIT display.rw DisplayString .1.3.6.1.4.1.33.13.1.100 |
xQueue OBJECT IDENTIFIER .1.3.6.1.4.1.33.13.2 |
queueLimitThe maximum number of entries that can be made in
the Queue table. The value -1 indicates the imit is
available memory. Corresponds directly to SERVER
QUEUE LIMIT and the value labeled 'Queue Limit:' in
the SERVER CHARACTERISTICS display.rw INTEGER (-1..100) .1.3.6.1.4.1.33.13.2.1 |
queueHighThe highest value of queueNumber since system
initialization. Corresponds directly to the value
labeled 'Queue Entries' and 'High' in the SERVER
STATUS display.ro Gauge .1.3.6.1.4.1.33.13.2.2 |
queueNumberThe number of entries in the Queue table.
Corresponds directly to the value labeled 'Queue
Entries' and 'Cur' in the SERVER STATUS display.ro Gauge .1.3.6.1.4.1.33.13.2.3 |
queueTableA list of queue entries. SEQUENCE OF QueueEntry .1.3.6.1.4.1.33.13.2.4 |
queueEntryParameter values for a queue entry. QueueEntry .1.3.6.1.4.1.33.13.2.4.1 |
queueJobThe job number of a queued request. Corresponds
directly to the value labeled 'Entry' in the QUEUE
display.ro INTEGER .1.3.6.1.4.1.33.13.2.4.1.1 |
queueStatusThe status of a queue entry. Set to 'invalid' to
remove the entry, which corresponds directly to the
REMOVE QUEUE ENTRY command. Actual removal of the
entry is implementation specific.rw Enumeration .1.3.6.1.4.1.33.13.2.4.1.2 |
queueSourceNameThe name of the system that originated the queue
entry. Corresponds directly to the value labeled
'Source Node' in the QUEUE display.ro DisplayString .1.3.6.1.4.1.33.13.2.4.1.3 |
queueServiceNameThe name of the service for which the originator is
waiting. Corresponds directly to the value labeled
'Service' in the QUEUE display.ro DisplayString .1.3.6.1.4.1.33.13.2.4.1.4 |
queueServicePortIndexThe charPortIndex of the port for which the
originator is waiting, if supplied by the
originator. As defined in the standard Character
MIB. Corresponds indirectly to the port number part
of the value labeled 'Port Name' in the QUEUE
display.ro INTEGER .1.3.6.1.4.1.33.13.2.4.1.5 |
queueServicePortNameThe name of the port for which the originator is
waiting, if supplied by the originator. Corresponds
directly to the port name part of the value labeled
'Port Name' in the SERVER QUEUE display.ro DisplayString .1.3.6.1.4.1.33.13.2.4.1.6 |
queuePortTableA list of queuing-related character port entries. SEQUENCE OF QueuePortEntry .1.3.6.1.4.1.33.13.2.5 |
queuePortEntryQueuing parameter values for a port. QueuePortEntry .1.3.6.1.4.1.33.13.2.5.1 |
queuePortIndexAn index value that uniquely identifies a port.
The port identified by a particular value of this
index is the same port as identified by
charPortIndex in the standard Character MIB.ro INTEGER .1.3.6.1.4.1.33.13.2.5.1.1 |
queuePortQueuingControl for allowing queued requests for using the
port. Corresponds directly to PORT QUEUING and the
presence of the label 'Queuing' following the label
'Enabled Characteristics:' in the PORT
CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.13.2.5.1.2 |
xMenu OBJECT IDENTIFIER .1.3.6.1.4.1.33.13.3 |
menuNumberThe number of entries in the Menu table.
Corresponds indirectly to SERVER MENU display.ro Gauge .1.3.6.1.4.1.33.13.3.1 |
menuContinuePromptThe text to use when prompting a menu user to press
RETURN to continue. Corresponds directly to SERVER
MENU CONTINUE PROMPT and the value labeled 'Menu
Continue Prompt:' in the SERVER MENU display.rw DisplayString .1.3.6.1.4.1.33.13.3.2 |
menuSelectionPromptThe text to use when prompting a menu user for a
menu selection. Corresponds directly to SERVER MENU
PROMPT and the value labeled 'Menu Prompt:' in the
SERVER MENU display.rw DisplayString .1.3.6.1.4.1.33.13.3.3 |
menuTableA list of menu entries. SEQUENCE OF MenuEntry .1.3.6.1.4.1.33.13.3.4 |
menuEntryParameter values for a menu entry. MenuEntry .1.3.6.1.4.1.33.13.3.4.1 |
menuIndexThe index number of a menu entry. Corresponds
directly to the numbers down the left of the SERVER
MENU display.ro INTEGER .1.3.6.1.4.1.33.13.3.4.1.1 |
menuStatusThe status of a the entry. Set to 'invalid' to
remove the entry, which corresponds directly to the
CLEAR SERVER MENU command. Actual removal of the
entry is implementation specific.rw Enumeration .1.3.6.1.4.1.33.13.3.4.1.2 |
menuTextThe text to be displayed in the menu. Corresponds
directly to the line next to the entry number in the
SERVER MENU display.rw DisplayString .1.3.6.1.4.1.33.13.3.4.1.3 |
menuCommandThe commands to execute when the user chooses the
menu entry. Corresponds directly second line
following the entry number in the SERVER MENU
display.rw DisplayString .1.3.6.1.4.1.33.13.3.4.1.4 |
menuPortTableA list of menu-related character port entries. SEQUENCE OF MenuPortEntry .1.3.6.1.4.1.33.13.3.5 |
menuPortEntryMenu parameter values for a port. MenuPortEntry .1.3.6.1.4.1.33.13.3.5.1 |
menuPortIndexAn index value that uniquely identifies a port.
The port identified by a particular value of this
index is the same port as identified by
charPortIndex in the standard Character MIB.ro INTEGER .1.3.6.1.4.1.33.13.3.5.1.1 |
menuPortMenuStatusControl for menu operation on the port.
Corresponds indirectly to PORT MENU and PORT
PRIVILEGED MENU and the presence of the labels
'Menu' and 'Privileged Menu' following the label
'Enabled Characteristics:' in the PORT
CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.13.3.5.1.2 |
menuPortNestedMenuStatusControl for nested menu operation on the port.
Corresponds indirectly to PORT NESTED MENU and the
presence of the label 'Nested Menu' following the
label 'Enabled Characteristics:' in the PORT
CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.13.3.5.1.3 |
menuPortNestedMenuPrivilegeControl for nested privileged menu operation on the
port. Corresponds indirectly to PORT NESTED
PRIVILEGED MENU and the presence of the label
'Nested Privileged Menu' following the label
'Enabled Characteristics:' in the PORT
CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.13.3.5.1.4 |
menuPortNestedTopLevelThe top level nested menu to select from the menu
definition file.rw INTEGER .1.3.6.1.4.1.33.13.3.5.1.5 |
menuNestedNameName of the script file containing the nested
menu.rw DisplayString .1.3.6.1.4.1.33.13.3.6 |
menuNestedScriptMaximumMaximum number of temporary storage bytes for a
nested menu script file. If not zero, the nested
menu function is enabled.rw INTEGER .1.3.6.1.4.1.33.13.3.7 |
menuNestedSystemNameControl to request to download a menu script which is
unique for this unit by prepending the sysLocalName of
this unit to the nestedMenuName.rw Enumeration .1.3.6.1.4.1.33.13.3.8 |
menuNestedEthernetControl to request to download a menu script which is
unique for this unit by prepending the Ethernet address,
or 802.3 MAC address, of this unit to the nestedMenuName.rw Enumeration .1.3.6.1.4.1.33.13.3.9 |
xNetLogin OBJECT IDENTIFIER .1.3.6.1.4.1.33.13.4 |
netLoginNumberThe number of entries in the Network Login Server
table.ro INTEGER .1.3.6.1.4.1.33.13.4.1 |
netLoginServerTableA list of network login server entries. SEQUENCE OF NetLoginServerEntry .1.3.6.1.4.1.33.13.4.2 |
netLoginServerEntryNetwork login parameter values for a server
entry. NetLoginServerEntry .1.3.6.1.4.1.33.13.4.2.1 |
netLoginServerNameThe name of a network login server, suitable for
resolution to a network address. Corresponds
directly to host portion of SERVER SCRIPT SERVER and
the value labeled 'Script Host' in the SERVER
PARAMETER SERVER display.ro DisplayString .1.3.6.1.4.1.33.13.4.2.1.1 |
netLoginServerStatusStatus of this entry. Set to 'invalid' to remove
the entry, which corresponds directly to the CLEAR
SERVER SCRIPT SERVER command. Actual removal of the
entry is implementation specific.rw Enumeration .1.3.6.1.4.1.33.13.4.2.1.2 |
netLoginServerPathThe full path name to the script file that is
identified by the user name. Corresponds directly
to path portion of SERVER SCRIPT SERVER and the
value labeled 'Script Path' in the SERVER PARAMETER
SERVER display. Defaults to the NULL string when
a new entry is created.rw DisplayString .1.3.6.1.4.1.33.13.4.2.1.3 |
netLoginServerSeparatorThe single character string that will be inserted
between the components of a file's path on the
script server. Defaults to the NULL string when
a new entry is created. Corresponds directly to the
separator portion of SERVER SCRIPT SERVER display.rw DisplayString .1.3.6.1.4.1.33.13.4.2.1.4 |
netLoginPortTableA list of network login character port entries. SEQUENCE OF NetLoginPortEntry .1.3.6.1.4.1.33.13.4.3 |
netLoginPortEntryNetwork login parameter values for a port. NetLoginPortEntry .1.3.6.1.4.1.33.13.4.3.1 |
netLoginPortIndexAn index value that uniquely identifies a port.
The port identified by a particular value of this
index is the same port as identified by
charPortIndex in the standard Character MIB.ro INTEGER .1.3.6.1.4.1.33.13.4.3.1.1 |
netLoginPortScriptUseControl for the script action taken when a user
logs in on the port. Corresponds directly to PORT
SCRIPT LOGIN and the value labeled 'Script Login:'
in the PORT ALTERNATE CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.13.4.3.1.2 |
netLoginPortScriptEchoControl for display of script operation on the port
when running a script. Corresponds directly to PORT
SCRIPT ECHO and the presence of the label 'Script
Echo' following the label 'Enabled Characteristics:'
in the PORT CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.13.4.3.1.3 |
netLoginPortLoaderAddressTypeThe type of network address contained in
netLoginPortLoaderAddress. 'unknown' means no
address has been defined. 'other' means no other
type value applies. 'ip' is an Internet IP address.
'ethernet' is an 802.3 MAC address. Corresponds
indirectly to the address part of the value labeled
'Script Loaded From:' in the PORT STATUS display.ro AddressType .1.3.6.1.4.1.33.13.4.3.1.4 |
netLoginPortLoaderAddressThe network address of the server that provided the
script for the current port login. Corresponds
directly the address part of the value labeled
'Script Loaded From:' in the PORT STATUS display.ro OCTET STRING .1.3.6.1.4.1.33.13.4.3.1.5 |
netLoginPortLoaderFileThe path and file name of the script used for the
current port login. Corresponds directly the file
name part of the value labeled 'Script Loaded
From:' in the PORT STATUS display.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.33.13.4.3.1.6 |
netLoginPortExecuteFileThe path and file name of a script to be executed
immediately on the port. Corresponds directly the
file name in the SCRIPT command.rw DisplayString .1.3.6.1.4.1.33.13.4.3.1.7 |
xDial OBJECT IDENTIFIER .1.3.6.1.4.1.33.13.5 |
dialPortTableA list of dial character port entries. SEQUENCE OF DialPortEntry .1.3.6.1.4.1.33.13.5.1 |
dialPortEntryDial parameter values for a port. DialPortEntry .1.3.6.1.4.1.33.13.5.1.1 |
dialPortIndexAn index value that uniquely identifies a port.
The port identified by a particular value of this
index is the same port as identified by
charPortIndex in the standard Character MIB.ro INTEGER .1.3.6.1.4.1.33.13.5.1.1.1 |
dialPortDialbackControl for use of dialback when a user logs in on
the port. Corresponds directly to PORT DIALBACK and
the presence of the label 'Dialback' following the
label 'Enabled Characteristics:' in the PORT
CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.13.5.1.1.2 |
dialPortDialbackTimeoutThe number of seconds to wait for remote modem
response when dialing back. Corresponds directly to
PORT DIALBACK TIMEOUT and the value labeled
'Dialback Timeout:' in the PORT ALTERNATE
CHARACTERISTICS display.rw INTEGER .1.3.6.1.4.1.33.13.5.1.1.3 |
dialPortDialoutA control to determine the state of a remote port after
it has been logged out from the remote side of the
connection. none will log out the port, query will ask
user what to do, slip and ppp will revert
to those protocolsrw Enumeration .1.3.6.1.4.1.33.13.5.1.1.4 |
dialPortDialbackNoUsernameControl which when enabled on a dialback port will not
prompt for a username upon dialing back. Instead the
original username is reused.rw Enumeration .1.3.6.1.4.1.33.13.5.1.1.5 |
xSessionLog OBJECT IDENTIFIER .1.3.6.1.4.1.33.13.6 |
sessionLogLimitThe maximum number of entries allowed in the
Session Log table. Corresponds directly to SERVER
ACCOUNTING ENTRIES and the value labeled 'Accounting
Entries:' in the SERVER CHARACTERISTICS display.rw INTEGER .1.3.6.1.4.1.33.13.6.1 |
sessionLogTableA list of session log entries. SEQUENCE OF SessionLogEntry .1.3.6.1.4.1.33.13.6.2 |
sessionLogEntryParameter values for a session log entry. SessionLogEntry .1.3.6.1.4.1.33.13.6.2.1 |
sessionLogIndexThe index number of a session log entry.
Corresponds directly to the order of the displayed
records in the SERVER ACCOUNTING display. The
maximum value is sessionLogLimit.ro INTEGER .1.3.6.1.4.1.33.13.6.2.1.1 |
sessionLogConnectionIDAn indentifying number for records relating to the
same connection, that is, the connect and disconnect
records, either of which can be missing.
Corresponds directly to value labeled 'Entry' the
SERVER ACCOUNTING display.ro INTEGER .1.3.6.1.4.1.33.13.6.2.1.2 |
sessionLogPortAn index value that uniquely identifies the port
where the event took place. The port identified by
a particular value of this index is the same port as
identified by charPortIndex in the standard
Character MIB. Corresponds directly to the value
labeled 'Port' in the SERVER ACCOUNTING display.ro INTEGER .1.3.6.1.4.1.33.13.6.2.1.3 |
sessionLogEventThe type of event. Corresponds directly to the
alphabetic part of the value labeled 'Type' in the
SERVER ACCOUNTING display. Type 15 is used by internal
processes that call the session log function with an
already formatted message.ro Enumeration .1.3.6.1.4.1.33.13.6.2.1.4 |
sessionLogEventDetailThe detailed reason for the event. Corresponds
directly to the numeric part of the value labeled
'Type' in the SERVER ACCOUNTING display.ro Enumeration .1.3.6.1.4.1.33.13.6.2.1.5 |
sessionLogUserNameThe user name logged in on the port when the event
occurred. Corresponds directly to the value labeled
'Username' in the SERVER ACCOUNTING display.ro DisplayString .1.3.6.1.4.1.33.13.6.2.1.6 |
sessionLogRemoteNameThe name of the session remote partner.
Corresponds directly to the value labeled
'Destination' in the SERVER ACCOUNTING display.ro DisplayString .1.3.6.1.4.1.33.13.6.2.1.7 |
sessionLogConnectTimeThe date and time that session connection occurred.
Corresponds directly to the value labeled 'Connect
Time' in the SERVER ACCOUNTING display.ro DateTime .1.3.6.1.4.1.33.13.6.2.1.8 |
sessionLogDisconnectTimeThe date and time that session disconnection
occurred. Corresponds directly to the value labeled
'Disconnect Time' in the SERVER ACCOUNTING
display.ro DateTime .1.3.6.1.4.1.33.13.6.2.1.9 |
sessionLogInCharactersThe number of characters that came into the port
for the session. Corresponds directly to the value
labeled 'Bytes In' in the SERVER ACCOUNTING
display.ro Counter .1.3.6.1.4.1.33.13.6.2.1.10 |
sessionLogOutCharactersThe number of characters that went out of the port
for the session. Corresponds directly to the value
labeled 'Bytes Out' in the SERVER ACCOUNTING
display.ro Counter .1.3.6.1.4.1.33.13.6.2.1.11 |
sessionLogVerboseEventWhen logging in 'verbose' mode, the event that
occured.ro Enumeration .1.3.6.1.4.1.33.13.6.2.1.12 |
sessionLogX25DirectionThe initial direction for an X.25 connection.
A value of 0 is returned if the session is
not X25ro Enumeration .1.3.6.1.4.1.33.13.6.2.1.13 |
sessionLogVerboseMessageText describing the event that was logged.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.33.13.6.2.1.14 |
sessionLogX25CallerAddressFor an X.25 connection, the X.121 source address.ro OCTET STRING .1.3.6.1.4.1.33.13.6.2.1.15 |
sessionLogX25CalledAddressFor an X.25 connection, the X.121 destination
address.ro OCTET STRING .1.3.6.1.4.1.33.13.6.2.1.16 |
sessionLogX25DisconnectCauseFor a terminated X.25 connection, the standard,
X.25 cause code.ro INTEGER .1.3.6.1.4.1.33.13.6.2.1.17 |
sessionLogX25DisconnectDiagnosticFor a terminated X.25 connection, the standard,
X.25 diagnostic code.ro INTEGER .1.3.6.1.4.1.33.13.6.2.1.18 |
sessionLogHostTypeThe type of host to which session log events are to
be sent.rw Enumeration .1.3.6.1.4.1.33.13.6.3 |
sessionLogHostAddressThe address of the host to receive events.rw OCTET STRING .1.3.6.1.4.1.33.13.6.4 |
sessionLogVerboseControl for verbose logging.rw Enumeration .1.3.6.1.4.1.33.13.6.5 |
sessionLogPriorityThe largest priority number for the system to log.
Higher numbered (lower priority) events will not be
logged.rw INTEGER .1.3.6.1.4.1.33.13.6.6 |
sessionLogEmptyControl to empty the log. In response to a
get-request or get-next-request, the agent always
returns 'ready' for this value. Setting the value
to 'ready' has no effect. Setting it to 'execute'
causes the log to be emptied.rw Enumeration .1.3.6.1.4.1.33.13.6.7 |
sessionLogFacilityThe UNIX facility level that server originated
accounting messages are logged to.rw Enumeration .1.3.6.1.4.1.33.13.6.8 |
sessionLogReliableControl for reliable logging. Corresponds directly to the
presence of the label 'Reliable Accounting' following the
label 'Enabled Characteristics:' in the SERVER
CHARACTERISTICS display.rw Enumeration .1.3.6.1.4.1.33.13.6.9 |
sessionLogHostSecondaryTypeThe type of secondary host to which session log events are
to be sent. This value should be set to unix when
configuring a non-zero sessionLogHostSecondaryAddress.
Corresponds to the presence of the label 'SYSLOGD Host2'
following the label 'Daemon(s)' in the SERVER UNIT
display.rw Enumeration .1.3.6.1.4.1.33.13.6.10 |
sessionLogHostSecondaryAddressThe address of a secondary host to receive events.
Corresponds directly to the value labeled
'SYSLOGD Host2' in the SERVER UNIT display.rw OCTET STRING .1.3.6.1.4.1.33.13.6.11 |
sessionLogZeroAccountingAllA control to clear all entries in the accounting log
including command log entries. Corresponds directly to
the command CLEAR SERVER ACCOUNTING ALL. In response to
a get-request or get-next-request the agent always returns
ready for this value.rw Enumeration .1.3.6.1.4.1.33.13.6.12 |
sessionLogZeroCommandLoggingA control to clear all command log entries. Corresponds
directly to the command CLEAR SERVER COMMAND LOGGING. In
response to a get-request or get-next-request the agent
always returns ready for this value.rw Enumeration .1.3.6.1.4.1.33.13.6.13 |
sessionLogTl1AutonomousLogSizeThe size in bytes of the TL1 autonomous log, which
records alarms. A change in log size will not take effect
until rebooting the unit.rw INTEGER ( 0..1000) .1.3.6.1.4.1.33.13.6.14 |
sessionLogTl1CommandLogSizeThe size in bytes of the TL1 command log, which records
all TL1 commands entered on this server. A change in log
size will not take effect until rebooting the unit.rw INTEGER ( 0..1000) .1.3.6.1.4.1.33.13.6.15 |
sessionLogZeroDataLoggingA control to clear all data log entries. Corresponds
directly to the command CLEAR SERVER DATA LOGGING. In
response to a get-request or get-next-request the agent
always returns ready for this value.rw Enumeration .1.3.6.1.4.1.33.13.6.16 |
sessionLogZeroAlarmLoggingControl to clear all alarm log entries. In response to a
get-request or a get-next-request the agent always returns
ready for this value.rw Enumeration .1.3.6.1.4.1.33.13.6.17 |
xCcl OBJECT IDENTIFIER .1.3.6.1.4.1.33.13.7 |
cclParsedScriptTableA list of parsed CCL scripts. SEQUENCE OF CclParsedScriptEntry .1.3.6.1.4.1.33.13.7.1 |
cclParsedScriptEntryParsed CCL script information. CclParsedScriptEntry .1.3.6.1.4.1.33.13.7.1.1 |
cclScriptNameThe name of a CCL script file that has been
loaded from a script server. Corresponds directly
to the name in a SERVER CCL command and the value
labeled 'CCL name:' in the PORT CHARACTERISTICS
display.ro DisplayString .1.3.6.1.4.1.33.13.7.1.1.1 |
cclScriptControlControl for maintaining the CCL script. The
refresh action consists of retrieving the script
by name from a script server and parsing it into
an executable format. This may be used to add an
entry to the table or refresh an existing entry with
a new version of the CCL script from the server.
This command may take ten seconds or more to complete
and may fail if the script file cannot be retrieved or
an error is encountered in parsing the CCL script.
An error value of genErr is returned upon refresh
failure. The refresh action corresponds directly to
the commnd: REFRESH SERVER CCL. Setting this field
to delete causes a script that is NOT being referenced
by any ports to be removed from the list and its
memory freed. This action corresponds directly to
the command: DELETE SERVER CCL. An error value of
badValue is returned upon delete failure.rw Enumeration .1.3.6.1.4.1.33.13.7.1.1.2 |
cclPortTableA list of ccl character port entries. SEQUENCE OF CclPortEntry .1.3.6.1.4.1.33.13.7.2 |
cclPortEntryCCL parameter values for a port. CclPortEntry .1.3.6.1.4.1.33.13.7.2.1 |
cclPortCclNameThe name of the ARAP modem CCL script file.rw DisplayString .1.3.6.1.4.1.33.13.7.2.1.1 |
cclPortModemAudibleThis boolean indicates if the CCL script should put
the modem into audible mode.rw Enumeration .1.3.6.1.4.1.33.13.7.2.1.2 |
xBroadcastGroup OBJECT IDENTIFIER .1.3.6.1.4.1.33.13.8 |
broadcastGroupTableA list of broadcast groups. SEQUENCE OF BroadcastGroupEntry .1.3.6.1.4.1.33.13.8.1 |
broadcastGroupEntryBroadcast group information. BroadcastGroupEntry .1.3.6.1.4.1.33.13.8.1.1 |
broadcastGroupIndexAn index value that uniquely identifies a broadcast group.ro INTEGER ( 1..10) .1.3.6.1.4.1.33.13.8.1.1.1 |
broadcastGroupStatusA status value for the broadcast group. The value 'enabled' means
that the group is active and broadcasting data whereas 'disabled'
means that the group is not active.rw Enumeration .1.3.6.1.4.1.33.13.8.1.1.2 |
broadcastGroupMasterAn index value that uniquely identifies the Master Broadcast Port
for this group. The port provided in this object is the same port
as identified by charPortIndex in the standard Character MIB.rw INTEGER .1.3.6.1.4.1.33.13.8.1.1.3 |
broadcastGroupSlavesA bitmap representing the ports included in this broadcast group.
A bit with a value of '1' means the corresponding port is included
in the broadcast group whereas a value of '0' indicates that the
port is not part of the broadcast group.rw OCTET STRING .1.3.6.1.4.1.33.13.8.1.1.4 |
broadcastGroupSlavesBroadcastOnlyA bitmap representing the ports set up to discard input data and
transmit only the broadcast data on the line. A bit set to '1'
means that the corresponding port will only broadcast the data and
discard any input.rw OCTET STRING .1.3.6.1.4.1.33.13.8.1.1.5 |
broadcastGroupSlaveTcpPortA TCP port number on which the broadcast group process will listen
for incoming TCP connections. A client connected to this
particular port will receive the data broadcast by the Master
Port. A value of '0' indicates that no TCP port is defined.rw INTEGER .1.3.6.1.4.1.33.13.8.1.1.6 |
broadcastGroupSlaveTcpBroadcastOnlySpecifies whether the TCP port will discard input characters
for the Master port so that the Master port operates in broadcast
only mode.rw Enumeration .1.3.6.1.4.1.33.13.8.1.1.7 |
xPingHosts OBJECT IDENTIFIER .1.3.6.1.4.1.33.13.9 |
pingHostsTableA list of ICMP ping hosts. SEQUENCE OF PingHostsEntry .1.3.6.1.4.1.33.13.9.1 |
pingHostsEntryPing Hosts information. PingHostsEntry .1.3.6.1.4.1.33.13.9.1.1 |
icmpPingHostIndexAn index value that uniquely identifies a ping host.ro INTEGER ( 1..24) .1.3.6.1.4.1.33.13.9.1.1.1 |
icmpPingHostAddressThe host address to be monitored to make sure it is
reachable using ICMP pings. This address must be
unique within the table, and must be Set to a non-zero
value prior to configuring the other attributes of
the ping host. A set-request with an IpAddress of
zero will make this entry inactive.rw IpAddress .1.3.6.1.4.1.33.13.9.1.1.2 |
icmpPingHostDescriptionThis is an optional description of the ping host.rw DisplayString .1.3.6.1.4.1.33.13.9.1.1.3 |
icmpPingHostNotificationTypeIndicates the type of notification used, if any,
when the ping host is determined to be unreachable.
If the type is snmp, a trap is sent to configured
trap clients.rw Enumeration .1.3.6.1.4.1.33.13.9.1.1.4 |
icmpPingHostPollingIntervalThe time in seconds between sending an ICMP ping to
a ping host in order to check for reachability.rw INTEGER ( 5..65535) .1.3.6.1.4.1.33.13.9.1.1.5 |
icmpPingHostMaximumRetriesThe maximum consecutive failed attempts to reach the
host via ICMP ping before sending notification as
specified by icmpPingHostNotificationType.rw INTEGER ( 1..255) .1.3.6.1.4.1.33.13.9.1.1.6 |
icmpPingHostTrapSeverityLevelIndicates the severity level of a trap to be sent out
when the host is unreachable.rw Enumeration .1.3.6.1.4.1.33.13.9.1.1.7 |
icmpPingHostStatusIndicates the current status of the ping host. If the
host is reachable, the status is cleared. Otherwise, it
is the same as the icmpPingHostTrapSeverityLevel.ro Enumeration .1.3.6.1.4.1.33.13.9.1.1.8 |