LJ3700-MIB
AI MIB Summary
The LJ3700-MIB module enables SNMP-based monitoring of HP LaserJet 3700 series printers, exposing standard counters for page counts, toner levels, and paper tray status alongside device health metrics such as error states and consumable life cycles.
Objects used in the HP LaserJet 3700 printer.
Main OID:
hp.1.3.6.1.4.1.11
713
Objects
Active
Status
1
Dependencies
Imported Objects
Objects
713 total| Object Name |
|---|
hpObjects used in the HP LaserJet 3700 printer. MODULE-IDENTITY .1.3.6.1.4.1.11 |
netPMLmgmt OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2 |
device OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1 |
device_system OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1 |
settings_system OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1 |
energy_starReturns or changes the Energy Star sleep value. If the value is greater than zero, then the device will go into energy saving sleep mode after the print engine has been idle for the number of seconds specified by this object. A value of zero means Energy Star is disabled and the device will not go to sleep based on print engine idle time. The value must be non-negative. Additional information: Returns or changes the Energy Star sleep value. The device will go into energy saving sleep mode after the print engine has been idle for the number of seconds specified by this object. LaserJet 3700 supports values of 0, 60, 900, 1800, 3600, 5400, 7200, 14400 seconds. A value of 0 means never enter sleep mode based on the print engine idle time. Setting to an unsupported value causes the printer to substitute a value (listed below) and to return <noError> status. Setting this value when the printer is in sleep mode will not cause it to wakeup unless it is set to 0. The values are as follow: <=0 snap to 0 >=1 and <= 479 snap to 60 (1 minute) >=480 and <= 1349 snap to 900 (15 minutes) >=1350 and <= 2699 snap to 1800 (30 minutes) >=2700 and <= 4499 snap to 3600 (1 hour) >=4500 and <= 6299 snap to 5400 (90 minutes) >=5400 and <= 10799 snap to 7200 (2 hours) >=10800 snap to 14400 (4 hours).rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.1 |
sleep_modeReturns eTrue if the device is in energy saving sleep mode, otherwise returns eFalse. Setting SLEEP-MODE to eFalse causes the device to wake up, if it is in sleep mode. Setting SLEEP-MODE to eTrue causes the device to go into sleep mode. Additional information: This object returns eTrue if the device is in energy saving sleep mode, otherwise it returns eFalse. Setting this object to eTrue while the printer is awake will not change the printer's current state and will return <genErr> status. NOTE: This object should behave this way when the printer does not have an instant-on fuser. Setting this object to eTrue while printer is already in Sleep Mode will not change the printer's current state and will return <noError> status. Setting this object to eFalse while printer is already awake will not change the printer's current state and will return <noError> status. Setting this object to eFalse while the printer is asleep causes the device to wake up.rw Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.2 |
mono_color_switching_modeThis object allows the user to view/change the color/mono switching mode for a device. Additional information: This object allows the user to change between three color mono switching modes. Automatic, optimize for speed and optimized for cost per page. The behaivor of these settings depend on the product being used, and is optimized based on the expected use of the product.rw Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.31 |
device_configure OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.32 |
device_configure_printer_parametersAllow the printer to be configured as a duplex or simplex printer. There will be a <<hidden>> encoded in this string and decoded by the printer firmware. If the <<hidden>> check passes the printer will be configured accordingly. Additional information: Used to configure LaserJet 3700 engines for duplex enabled or not. Encoded confiugration string is passed in, which is decoded by firmware. Firmware verifies config. string is valid, and retrieves device Configuration data. Expandable to acomodate future products configuration needs.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.32.12 |
status_system OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2 |
on_off_lineTo bring the PDL processing sub-system on or off line. If the device is a printer, then the printer does not process print job data when the printer is off line. PML communication persists. Additional information: When the printer is in the Offline state, printing will stop as soon as possible (no more sheets of media are pulled from input trays). The I/O is taken offline also. Setting to eOnline has the following affect: Printer will immediately go to or remain in the Online state; <noError> status is returned. If the printer's current state is Offline with a pending error condition that prevents the printer from going to the Online state, the printer will remain in the Offline state; <genErr> status is returned (see the Control Panel ERS for a list of error conditions). Setting to eOffline has the following affect: Printer will immediately go to or remain in the Offline state; <noError> status is returned. If pages are being printed, those pages will complete with the printer in the Offline state. Setting to eOfflineAtEndOfJob has the following affect: If not in a job or already in the Offline state, the printer will immediately go to or remain in the Offline state; <noError> status is returned. If in a job and the current state is Online, the printer will remain in the Online state, with the value of this object as eOfflineAtEndOfJob, until the end of the job; <noError> status is returned. At the end of the job, the printer goes to the Offline state and the value of this object becomes eOffline. Setting this object to eOffline or eOnline before the end of the job causes the action for that value to be taken immediately.rw Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.5 |
_pysmi_continueA device can support a class of errors called continuable errors. When a continuable error is encountered, the device requires a continue event to occur before the device will continue operation. One continue event is setting the CONTINUE object to eInitiateAction. Devices can support other continue events, like auto-continue. A continue event causes the continuable error to be acknowledged, thus allowing the device to continue. Each device needs to list the continuable errors. If the device doesn't currently have an unacknowledged continuable error, the response will contain <genErr>. Additional information: See the CLEARABLE-WARNING and AUTO-CONTINUE objects for the errors that this object will clear.rw Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.6 |
auto_continueIndicates if the device will automatically continue after encountering a continuable error. If AUTO-CONTINUE is set to eOn, the device will automatically generate continue event to acknowledge continuable errors. If AUTO-CONTINUE is set to eOff, then some other continue event will have to acknowledge the continuable error. Additional information: If this is set to eOn the device displays an error message and goes offline for ten seconds. After ten seconds the printer automatically returns to the online state. If this is set to eOff then the device displays an error message and goes offline. It remains offline until the operator presses the GO key or until the CONTINUE object is set. If the printer is not idle, the new value may not take effect until a job boundary is reached. If a get is done on this object before the job boundary is reached, the value last set will be returned.rw Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.7 |
install_dateIdentifies the date that the device was installed. The format of the string is 'YYYYMMDDHHmmZ'. Where: YYYY is the year. MM is the month (1-12). DD is the day (1-31). HH is the hour of the day (0-23). mm are the minutes (0-59). 'Z' designates Greenwich Mean Time; if 'Z' not specified, value is local time. Device POS must specify the conditions for setting this object. Additional information: Setting the SERVICE-PASSWORD object will enable setting this object.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.8 |
perm_store_init_occurredThis object will set the cAllPermDevices bit when a full perm storage initialization occurs (as would be the case for a brand new system or as a result of a powerup key sequence or PE-TEST-POWERUP-KEY-SEQUENCE object request). If only one device was initialized (as would be the case if a disk were added to an existing system or a formatter were swapped out), then only the appropriate collection bits will be returned. If there are no collection bits set then this indicates that no initialization took place.ro OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.10 |
timestampSets the printer's current time in (UTC). The format of the string is 'YYYYMMDDHHMMSS'. Where YYYY is the year. MM is the month (1-12) DD is the day of the month (1-31) HH is the hour of the day (0-23) MM is the minutes (0-59) SS is the seconds (0-59) Device POS must specify the conditions for setting this object.rw DisplayString .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.13 |
service_idA read of this object will return the current SERVICE ID value in the printer. The format is 'YYDDD' where: YY = calendar year - 1990 DDD = (calendar month - 1) * 30 + (calendar day of the month or 30, if > 30) A write of this object will only succeed if the MANUFACTURING-CONTROL PML object has been set with the correct <<hidden>>. If the write operation is not allowed, this object will return an <genErr> status. Additional information: Setting the SERVICE-PASSWORD object will enable setting this object.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.19 |
display OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.20 |
display_status OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.20.1 |
show_addressIf this object is set to eAuto, and the device has an IP address, the IP address of the device will be shown with the READY message. If this object is set to eOff, the IP address will not be shown.rw Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.20.1.3 |
display_physical_appearanceThis object configures the default brightness setting of the control panel based on a categorization of the display as either light, normal, or dark.rw Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.20.1.4 |
job_input_auto_continue_timeoutThe number of seconds the device waits after a job related continuable error occurs before automatically continuing. An example job related continuable error is the job requesting a media size that is not available. After the timeout expires, the device will continue processing the job as if a continue event occurred, such as the front panel continue key being pressed. If the value is -1, the device does not automatically continue after a job related continuable error occurs. If the value is 0, the device immediately continues. If the value is greater than 0, the value represents the timeout value in seconds. Additional information: This object is used only for media requests (size and/or name). LaserJet 8150 supports any value in the range of -1 to 3600. Setting to a value outside of that range causes the printer to substitute a value (listed below) and to return <noError> status. The values are as follow: <-1 snaps to -1 >3600 snaps to 3600 (60 minutes) The action that occurs when this timeout expires is explained by JOB-INPUT-AUTO-CONTINUE-MODE. It is not the same as the CONTINUE object being set to eInitiateAction or the Select key being pressed on the control panel. See the LaserJet 8150 Control panel ERS, LaserJet 8150 Paper Handling ERS, and the CONTINUE object description for information on the actions that occur for those conditions. The data for this object is stored in NVRAM.rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.35 |
job_input_auto_continue_modeReturns or sets the device behavior when the desired media is not currently available. cCancelJob - The device cancels the job. The device POS should explain what happens if this item is not the only item in the collection. cAutoMediaSizeOverride - The device is allowed to substitute a different size media. cAutoMediaNameOverride - The device is allowed to substitute a different media name. cUSMediaSizeOverride - The device is allowed to substitute US media sizes (letter, etc.) for ISO media sizes (A4, etc.). cISOMediaSizeOverride - The device is allowed to substitute ISO media sizes (A4, etc.) for US media sizes (letter, etc.). Additional information: If cCancelJob is set, the current print job will be canceled regardless of other item settings. At least one bit of the collection must be set; setting this object to zero will cause a status of <badValue> to be returned. This object applies to all media requests, including Manual Feed Requests. This object describes the action that is performed when the JOB-INPUT-AUTO-CONTINUE-TIMEOUT expires. The action performed by the CONTINUE object being set to eInitiateAction or the GO key being pressed on the control panel may cause different actions. See the LaserJet 8150 Control panel ERS, LaserJet 8150 Paper Handling ERS and the CONTINUE object description for information on the actions that occur for those conditions. The data for this object is stored in NVRAM.rw OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.36 |
background_message OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.37 |
background_message1 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.37.1 |
background_status_msg_line1_part1The string displayed on the device's front panel in place of the printer's built-in background status string. An example built-in background status string is '00 READY'. Additional information: The display size for the LaserJet 8150 printers is 2 X 16. The value of this object and the current value of BACKGROUND-STATUS-MSG-LINE2-PART1 are displayed together on the 2-line display, but they must be set independently. If line 2 has been set, and the next message to be displayed only requires line 1, BACKGROUND-STATUS-MSG-LINE2-PART1 must be set to the null string to clear it. This object allows a message to be displayed when it is the highest priority message. Setting this object does not guarantee the message will be displayed; and reading it returns the value last written, not the currently displayed message (use prtConsoleDisplayBufferText to read the display). The priority assigned for displaying this message is one lower than the READY message. In other words, the only message that can be replaced by these objects is the READY message. To clear the message, write a null string to both this object and BACKGROUND-STATUS-MSG-LINE2-PART1.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.37.1.1 |
background_message2 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.37.2 |
background_status_msg_line2_part1The string displayed on the device's front panel in place of the printer's built-in background status string. An example built-in background status string is '00 READY'. Additional information: See BACKGROUND-STATUS-MSG-LINE1-PART1rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.37.2.1 |
error_log_clearSetting this object clears all the entries in the error log sub-tree. Additional information: Setting this object removes all errors that have been stored in the printer's non-volatile memory.rw Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.38 |
job_output_auto_continue_timeoutReturns or sets the time that the printer will wait after an output bin becomes full and the printer is trying to deliver a sheet of media to that output bin. When the timeout expires, the job is processed according to the OUTBINn-OVERRIDE-MODE. A value of -1 indicates that the printer will wait for a continue event. A non-negative value is the number of seconds to wait. Additional information: A value of zero means to continue immediately. The value of this object is stored in NVRAM, so it is maintained across a power cycle. The data for this object is stored in NVRAM.rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.40 |
collated_originals_supportIndicates that the printer can create multiple, collated 'originals' of a job and shows the level of support for this capability. cCollatedOriginals - The printer can create multiple collated originals, or 'mopies'. This is the base functionality required by the other collection items. cProofAndHold - The printer saves a copy of the job while printing the first mopy. Later, this held job can be released and the rest of the mopies will print. cSecurityPrint - The printer spools the job and holds the job until the user releases the job by entering a <<hidden>> at the printer's control panel. cAutoHighlight - The printer prints the job a number of times with a mail distribution list prepended to each job. A different mailing address is highlighted on each mopy. cCollatedAtSpeed - The printer can create multiple collated copies where all copies after the original are printed at engine speed. Additional information: Indicates that the printer can create multiple, collated originals of a job and shows the level of support for this capability. cCollatedOriginals - The printer can create multiple collated originals, or mopies. This is the base functionality required by the other collection items. Without disk, this object will not exist. This will be set at boot-up initialization. If the disk fails, in any way, then the disk error functionality will handle the situation. A color printer (LaserJet 4550) that only has a RAMDISK installed is treated like there is no disk and therefore this object will not exist. The value of this object will be: !cCollatedOriginals - Only FLASH installed cCollatedOriginals - IDE is installed combined with/without FLASH cCollatedOriginals - RAMDISK is On combined with/without FLASHro OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.42 |
localization_languages_supportedThe list of languages supported by the device. The languages are primarily, but not limited to, two character codes from ISO 639, each separated by a comma character. Additional information: This string will always be in the Roman-8 character set. See prtLocalizationLanguage for details about each language value.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.52 |
localization_countries_supportedThe list of countries supported by the device. The countries are primarily, but not limited to, two character codes from ISO 3166, each separated by a comma character. Additional information: This string will always be in the Roman-8 character set. See prtLocalizationCountry for details about each country value.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.53 |
host_application_available_memoryReturns the amount of memory, in bytes, that the device has available for job-related processing or resources. Also known as driver work space (DWS) memory.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.59 |
control_panel_button_pressWriting this object simulates pressing a button on the control panel. Reading it will return the last key pressed either on the control panel or via PML. The device POS will specify which keys are supported.rw Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.60 |
control_panel_display_contents_change_counterA counter which increments whenever the contents of the front panel display changes. This object is implemented as a 32-bit signed integer which rolls over to zero when it reaches a maximum value.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.63 |
control_panel_display_contents_crcReading this object returns a 32-bit Cyclical Redundancy Check (CRC) which represents the current contents of the display. Additional information: This object has been implimented as an 8-bit CRC for this product.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.64 |
control_panel_display OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.65 |
control_panel_display_graphical_contentsReading this object returns a graphical file format image representing the current pixel content of the display. The device POS will specify the expected screen resolution, color depth of the display and graphics file format for a given product (eg. 160x64x1 GIF format OR 640x240x4 JPEG format). If the image is large enough that it needs to be returned in multiple objects then each array object will contain a portion of the image. The image will then need to be reconstructed by a host application. An application that needs to determine if their is an additional object to be retreived will need to perform a GETNEXT operation until there are no more objects in the sub-tree. Additional information: This object returns a GIF image that represents the current contents of the 160x64x1 control panel display. Most display images require more than one instance of this object in order to retreive the complete GIF image.ro OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.65.1 |
control_panel_key_pressWriting this object simulates pressing a key on the control panel. Reading it will return the last key pressed either on the control panel or via PML. This object obsoletes/replaces CONTROL-PANEL-BUTTON-PRESS object which was unable to represent each of the possible key combinations of our current control panels (ie. Full QWERTY keyboard). The device POS will specify the full range of keys supported by this object. Additional information: Writing this object simulates pressing a key on the control panel. Reading it will return the last key pressed either on the control panel or via PML. This object obsoletes/replaces CONTROL-PANEL-BUTTON-PRESS object which was unable to represent each of the possible key combinations of our current control panels (ie. Full QWERTY keyboard). For non-MFP products that do not use touch screen control panels, key codes other than those assigned to physical buttons are treated as invalied keycodes. Key Map for currently Supported Keys: Key Name Key Code ---------------------------------------- Menus 129 Stop 130 Clear 132 Select(Check) 133 Back (Left) Arrow 135 Down Arrow 136 Up Arrow 137 ? (Help) 139rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.66 |
page_frame_memory_availableReturns the abount of page-frame memory in bytes available in the system. Additional information: Total amount of pageframe memory, in kilobytes, present in the printer.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.72 |
id OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.3 |
model_numberIdentifies the device model number as listed in the HP corporate price list (e.g. C2121A for DeskJet 500C). The string is as specific as possible. Products should note in POS if the model number on the CPL changes but the device reports the previous model number. If the model number changes based on the installed options, the POS should indicate if only the base model number is returned, or if the device senses the installed options and returns the correct model number. If possible, encode the model number in a symbol set (like Roman-8) that matches the ASCII character set and limit the characters used to ASCII characters. Additional information: The value of this object does not change based on the installed options. The default of this object is the same on all LaserJet 8150 printers.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.1.3.1 |
model_nameIdentifies the device model name (e.g. ''DeskJet 1200C''). The string is as specific as possible. Capitalization and spacing should match family naming conventions. Products should note in POS if the model name on the HP corporate price list changes but the device reports the previous device name. If the model name changes based on the installed options, the POS should indicate if only the base model name is returned, or if the device senses the installed options and returns the correct model name. If possible, encode the model name in a symbol set (like Roman-8) that matches the ASCII character set and limit the characters used to ASCII characters. Additional information: Since the value of this object is frequently used in displaying a list of printers, it is kept relatively short in case systems have limited width for their display area. The model name does not change based on sensing of installed options.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.1.3.2 |
serial_numberIdentifies the serial number for the device. If the SERIAL-NUMBER object is set by the user, then setting the object does not need to be protected. If the SERIAL-NUMBER object is set at the factory, then the SERVICE-PASSWORD object must be set correctly before the SERIAL-NUMBER object is writable. If this is a writable object, the POS should indicate the maximum supported string length. If possible, encode the serial number in a symbol set (like Roman-8) that matches the ASCII character set and limit the characters used to ASCII characters. Additional information: This value IS AFFECTED BY NVRAM resets, it is set to the default value of XXXXXXXXXX, when a NVRAM init is done.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.1.3.3 |
fw_rom_datecodeIdentifies the base system firmware date code. The date code will be encoded in the yyyymmdd format. There may be several versions of the base system firmware. The date code associated with the version of the base system firmware that is being used is reported. There may be other date code objects for other specific modules such as fonts, localization modules, etc.; these other datecode objects are device specific.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.1.3.5 |
fw_rom_revisionThis identifies the system code firmware ROM revision code. The format for a revision is major_revision.minor_revision. There may be other ROM revision code objects for other specific ROMs such as font ROMs, localization ROMs, etc; these other ROM revision code objects are device specific.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.1.3.6 |
device_nameUser defined device name. The POS should indicate the maximum supported string length. If the user entered string is too long, the device will store as much as possible and will return the <OKNearestLegal ValueSubstituted>.Additional information: The maximum supported string length is 32 characters. If the user entered string is too long, the device will store the first 32 characters and will return the <noError> status.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.1.3.10 |
device_locationUser defined device location. The POS should indicate the maximum supported string length. If the user entered string is too long, the device will store as much as possible and will return the <OKNearestLegal ValueSubstituted>.Additional information: The maximum supported string length is 16 characters. If the user entered string is too long, the device will store the first 16 characters and will return the <noError> status.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.1.3.11 |
asset_numberUser defined asset number. The POS should indicate the maximum supported string length. If the user entered string is too long, the device will store as much as possible and will return the <OKNearestLegal ValueSubstituted>.Additional information: The maximum supported string length is 8 characters. If the user entered string is too long, the device will store the first 8 characters and will return the <noError> status.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.1.3.12 |
interface OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4 |
simm OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1 |
simm1 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.1 |
simm1_typeReturns an indication of the type of option installed in SIMM slot 1. eEmpty means the device did not detect any option installed in the interface slot. eUnknown means the device doesn't recognize the installed option. eUnSupported means the device recognizes the installed option, but does not support the option. eReadOnlyMemory means the installed option contains ROM Ics. eVolatileRandomAccessMemory means the installed option contains RAM ICs that loose data when the power is turned off. eNonVolatileRandomAccessMemory means that the installed option contains RAM ICs that do not loose data when the power is turned off. eFlashMemory means that the installed option contains a type of non-volatile RAM that needs to be erased before it can be written. eDiskDrive means the installed option contains a disk drive. eRamRom means the installed option contains both volatile random access memory and read only memory. eInputPHD means the installed option is an input paper handling device. eOutputPHD means the installed option is an output paper handling device. eIOCard means the installed option is an I/O card. Additional information: This object is used for describing DIMMs instead of SIMMs on LaserJet 8150. eRamRom is used to denote LaserJet 8150's combo simm.ro Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.1.4 |
simm1_capacityReturns an indication of the capacity of the SIMM installed in SIMM slot 1. The capacity is dependent on the type of option, as indicated by the SIMM1-TYPE object. This object has no meaning if the installed option type is eUnknown or eReadOnlyMemory. This object contains the size, in bytes, if the installed option type is eVolatileRandomAccessMemory, eNonVolatileRandomAccessMemory, eFlashMemory, or eDiskDrive. If the type of the installed option is eRamRom, this object contains the size, in bytes, of the random access memory. If the type of the installed option is eInputPHD, the capacity indicates the number of input trays supported by the installed option. If the type of the installed option is eOutputPHD, the capacity indicates the number of output bins supported by the installed option. If the type of the installed option is eIOCard, the capacity indicates the number of logical I/O ports supported by the I/O card. Additional information: Returns an indication of the capacity of the installed option in bytes. This object is not supported unless the SIMM1-TYPE type is eVolatileRandomAccessMemory, eRamRom, or eFlashMemory. For eRamRom only the size of the Ram portion of the SIMM is returned.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.1.5 |
simm1_bank OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.1.6 |
simm1_bank1 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.1.6.1 |
simm1_bank1_typeReturns an indication of the type of option installed in Bank 1 of SIMM slot 1. See SIMM1-TYPE for a description. Additional information: This object is used for describing the type of DIMM banks. Each physical DIMM slot has up to 2 banks.ro Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.1.6.1.1 |
simm1_bank1_capacityReturns an indication of the capacity of Bank 1 of the SIMM installed in SIMM slot 1. See SIMM1-CAPACITY for a description. Additional information: Returns an indication of the capacity of the installed bank option in bytes. This object is not supported unless the SIMM1-BANK1-TYPE type is eReadOnlyMemory, eFlashMemory, eEDORandomAccessMemory, eSDRandomAccessMemory, eSRandomAccessMemory, or eFPMRandomAccessMemory.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.1.6.1.2 |
simm1_bank2 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.1.6.2 |
simm1_bank2_typeReturns an indication of the type of option installed in Bank 2 of SIMM slot 1. See SIMM1-TYPE for a description. Additional information: This object is used for describing the type of DIMM banks. Each physical DIMM slot has up to 2 banks.ro Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.1.6.2.1 |
simm1_bank2_capacityReturns an indication of the capacity of Bank 2 of the SIMM installed in SIMM slot 1. See SIMM1-CAPACITY for a description. Additional information: Returns an indication of the capacity of the installed bank option in bytes. This object is not supported unless the SIMM1-BANK2-TYPE type is eReadOnlyMemory, eFlashMemory, eEDORandomAccessMemory, eSDRandomAccessMemory, eSRandomAccessMemory, or eFPMRandomAccessMemory.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.1.6.2.2 |
simm2 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.2 |
simm2_typeReturns an indication of the type of option installed in SIMM slot 2. See SIMM1-TYPE for a description. Additional information: This object is used for describing DIMMs instead of SIMMs on LaserJet 8150. eRamRom is used to denote LaserJet 8150's combo simm.ro Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.2.4 |
simm2_capacityReturns an indication of the capacity of the SIMM installed in SIMM slot 2. See SIMM1-CAPACITY for a description. Additional information: This object is used for describing DIMMs instead of SIMMs on LaserJet 8150. Returns an indication of the capacity of the installed option in bytes. This object is not supported unless the SIMM2-TYPE type is eVolatileRandomAccessMemory, eRamRom, or eFlashMemory. For eRamRom only the size of the Ram portion of the SIMM is returned.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.2.5 |
simm2_bank OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.2.6 |
simm2_bank1 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.2.6.1 |
simm2_bank1_typeReturns an indication of the type of option installed in Bank 1 of SIMM slot 2. See SIMM1-TYPE for a description. Additional information: This object is used for describing the type of DIMM banks. Each physical DIMM slot has up to 2 banks.ro Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.2.6.1.1 |
simm2_bank1_capacityReturns an indication of the capacity of Bank 1 of the SIMM installed in SIMM slot 2. See SIMM1-CAPACITY for a description. Additional information: Returns an indication of the capacity of the installed bank option in bytes. This object is not supported unless the SIMM2-BANK1-TYPE type is eReadOnlyMemory, eFlashMemory, eEDORandomAccessMemory, eSDRandomAccessMemory, eSRandomAccessMemory, or eFPMRandomAccessMemory.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.2.6.1.2 |
simm2_bank2 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.2.6.2 |
simm2_bank2_typeReturns an indication of the type of option installed in Bank 2 of SIMM slot 2. See SIMM1-TYPE for a description. Additional information: This object is used for describing the type of DIMM banks. Each physical DIMM slot has up to 2 banks.ro Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.2.6.2.1 |
simm2_bank2_capacityReturns an indication of the capacity of Bank 2 of the SIMM installed in SIMM slot 2. See SIMM1-CAPACITY for a description. Additional information: Returns an indication of the capacity of the installed bank option in bytes. This object is not supported unless the SIMM2-BANK2-TYPE type is eReadOnlyMemory, eFlashMemory, eEDORandomAccessMemory, eSDRandomAccessMemory, eSRandomAccessMemory, or eFPMRandomAccessMemory.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.2.6.2.2 |
simm3 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.3 |
simm3_typeReturns an indication of the type of option installed in SIMM slot 3. See SIMM1-TYPE for a description.ro Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.3.4 |
simm3_capacityReturns an indication of the capacity of the SIMM installed in SIMM slot 3. See SIMM1-CAPACITY for a description. Additional information: This object is used for describing DIMMs instead of SIMMs on LaserJet 8150. Returns an indication of the capacity of the installed option in bytes. This object is not supported unless the SIMM3-TYPE type is eVolatileRandomAccessMemory, eRamRom, or eFlashMemory. For eRamRom only the size of the Ram portion of the simm is returned.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.3.5 |
simm3_bank OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.3.6 |
simm3_bank1 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.3.6.1 |
simm3_bank1_typeReturns an indication of the type of option installed in Bank 1 of SIMM slot 3. See SIMM1-TYPE for a description. Additional information: This object is used for describing the type of DIMM banks. Each physical DIMM slot has up to 2 banks.ro Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.3.6.1.1 |
simm3_bank1_capacityReturns an indication of the capacity of Bank 1 of the SIMM installed in SIMM slot 3. See SIMM1-CAPACITY for a description. Additional information: Returns an indication of the capacity of the installed bank option in bytes. This object is not supported unless the SIMM3-BANK1-TYPE type is eReadOnlyMemory, eFlashMemory, eEDORandomAccessMemory, eSDRandomAccessMemory, eSRandomAccessMemory, or eFPMRandomAccessMemory.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.3.6.1.2 |
simm3_bank2 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.3.6.2 |
simm3_bank2_typeReturns an indication of the type of option installed in Bank 2 of SIMM slot 3. See SIMM1-TYPE for a description. Additional information: This object is used for describing the type of DIMM banks. Each physical DIMM slot has up to 2 banks.ro Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.3.6.2.1 |
simm3_bank2_capacityReturns an indication of the capacity of Bank 2 of the SIMM installed in SIMM slot 3. See SIMM1-CAPACITY for a description. Additional information: Returns an indication of the capacity of the installed bank option in bytes. This object is not supported unless the SIMM3-BANK2-TYPE type is eReadOnlyMemory, eFlashMemory, eEDORandomAccessMemory, eSDRandomAccessMemory, eSRandomAccessMemory, or eFPMRandomAccessMemory.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.3.6.2.2 |
simm4 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.4 |
simm4_typeReturns an indication of the type of option installed in SIMM slot 4. See SIMM1-TYPE for a description.ro Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.4.4 |
simm4_capacityReturns an indication of the capacity of the SIMM installed in SIMM slot 4. See SIMM1-CAPACITY for a description. Additional information: This object is used for describing DIMMs instead of SIMMs on LaserJet 8150. Returns an indication of the capacity of the installed option in bytes. This object is not supported unless the SIMM4-TYPE type is eVolatileRandomAccessMemory, eRamRom, or eFlashMemory. For eRamRom only the size of the Ram portion of the simm is returned.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.4.5 |
simm4_bank OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.4.6 |
simm4_bank1 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.4.6.1 |
simm4_bank1_typeReturns an indication of the type of option installed in Bank 1 of SIMM slot 4. See SIMM1-TYPE for a description. Additional information: This object is used for describing the type of DIMM banks. Each physical DIMM slot has up to 2 banks.ro Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.4.6.1.1 |
simm4_bank1_capacityReturns an indication of the capacity of Bank 1 of the SIMM installed in SIMM slot 4. See SIMM1-CAPACITY for a description. Additional information: Returns an indication of the capacity of the installed bank option in bytes. This object is not supported unless the SIMM4-BANK1-TYPE type is eReadOnlyMemory, eFlashMemory, eEDORandomAccessMemory, eSDRandomAccessMemory, eSRandomAccessMemory, or eFPMRandomAccessMemory.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.4.6.1.2 |
simm4_bank2 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.4.6.2 |
simm4_bank2_typeReturns an indication of the type of option installed in Bank 2 of SIMM slot 4. See SIMM1-TYPE for a description. Additional information: This object is used for describing the type of DIMM banks. Each physical DIMM slot has up to 2 banks.ro Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.4.6.2.1 |
simm4_bank2_capacityReturns an indication of the capacity of Bank 2 of the SIMM installed in SIMM slot 4. See SIMM1-CAPACITY for a description. Additional information: Returns an indication of the capacity of the installed bank option in bytes. This object is not supported unless the SIMM4-BANK2-TYPE type is eReadOnlyMemory, eFlashMemory, eEDORandomAccessMemory, eSDRandomAccessMemory, eSRandomAccessMemory, or eFPMRandomAccessMemory.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.4.6.2.2 |
mio OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3 |
mio1 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3.1 |
mio1_model_nameReturns product information identifying the I/O card. Example: XXXX.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3.1.2 |
mio1_manufacturing_infoReturns information describing the manufacture of the I/O card installed in MIO/EIO slot 1. May include serial number and firmware revision. Additional information: The format of the string returned is determined by the manufacturer of the EIO device. There is no standard for content of the string.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3.1.3 |
mio1_typeReturns an indication of the type of option installed in MIO/EIO slot 1. See SIMM1-TYPE for an explanation of the enumerations.ro Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3.1.4 |
mio2 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3.2 |
mio2_model_nameReturns product information identifying the I/O card. Example: XXXX.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3.2.2 |
mio2_manufacturing_infoReturns information describing the manufacture of the I/O card installed in MIO/EIO slot 2. May include serial number and firmware revision. Additional information: The format of the string returned is determined by the manufacturer of the EIO device. There is no standard for content of the string.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3.2.3 |
mio2_typeReturns an indication of the type of option installed in MIO/EIO slot 2. See SIMM1-TYPE for an explanation of the enumerations.ro Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3.2.4 |
mio3 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3.3 |
mio3_model_nameReturns product information identifying the I/O card. Example: XXXX.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3.3.2 |
mio3_manufacturing_infoReturns information describing the manufacture of the I/O card installed in MIO/EIO interface 3. May include serial number and firmware revision. Additional information: The format of the string returned is determined by the manufacturer of the EIO device. There is no standard for content of the string.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3.3.3 |
mio3_typeReturns an indication of the type of option installed in MIO/EIO interface 3. See SIMM1-TYPE for an explanation of the enumerations.ro Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3.3.4 |
socket_ping OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.7 |
socket_ping_job_events_versionThis object reports the current version of the Socket Ping Job Events capability. The version number is returned as a string in the format MAJOR.MINOR.SUB version. (eg. 1.0.1) If socket ping is not supported by this printer then the object is either not implemented or it returns a '0'.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.7.1 |
test OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.5 |
self_testWriting this object allows a device self test to be started. Reading this object provides an indication what self-test is currently executing, if any. Actual self-test operation is device specific. A self test may not be allowed at any arbitrary time. If the device supports the requested self test, but can not start the execution of the self test when requested, the device will respond with <genErr>. If a non-destructive self test is being started, the device will generate a response before the self test is completed. RECOMMENDATION: If the device is ready (i.e. the NOT-READY-PRINTER object does not contain any items, except maybe being off-line) and is idle (i.e. the NOT-IDLE object does not contain any items), this request should always succeed. This provides a mechanism for driver writers to always determine if the action will succeed or not. Additional information: The eNonDestructiveSelfTest performs limited testing on the printer and its attached paper handling devices. After the self-test is complete a configuration page is printed. The recommended way to cause a configuration page to be printed is to use the PRINT-INTERNAL-PAGE object. Setting this object to eNonDestructiveSelfTest results in a status of <noError> and a value of eNonDestructiveSelfTest being returned. If the printer is not idle (whether printing an external job or printing an internal page), this action will be delayed until the next job boundary. See the PRINT-INTERNAL-PAGE object for more details.rw Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.5.1 |
print_internal_pageWriting this object to a value other than eNotPrintingAnInternalPage causes the device to attempt to print an internally generated page. Reading this object provides an indication what internally generated page is currently being printed, if any. The actual page is device specific. Some devices may support continuously printing an internally generated page. Setting this object to eNotPrintingAnInternalPage terminates continuously printing internally generated pages. An internally generated page may not be allowed to be printed at any arbitrary time; under what conditions it will succeed or fail is device specific. If the device supports the requested page, but can not start printing the page when requested, the device will respond with <genErr>. RECOMMENDATION: If the device is ready (i.e. the NOT-READY-PRINTER object does not contain any items, except maybe being off-line) and is idle (i.e. the NOT-IDLE object does not contain any items), this request should always succeed. This provides a mechanism for driver writers to always determine if the action will succeed or not. Additional information: Previous products used ePCLDemoPage1ConfigurationPage(300) for the Configuration or Self Test page. This product uses eDeviceDemoPage1ConfigurationPage(3). LaserJet 8150 does not support continuously printing a demo page. When this object is set to a valid value, the status returned is <noError> and the value returned is ePrintingAnUnknownInternalPage. If the printer is idle, the page will be printed immediately. If the printer is currently printing another job, the internal page requested will not print until that job is finished. Setting this object to a valid value causes the desired page to be formatted and put in the printer's print queue. While the page is being formatted a get on this object will return the value ePrintingAnUnknownInternalPage. Once the page (or pages) is finished being formatted, this object returns a value of eNotPrintingAnInternalPage, even though the page may not have finished being printed. Setting this object multiple times will queue up the requests, but only a limited number will be queued. Once the queue is full, additional requests will be ignored.rw Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.5.2 |
engine_self_diagnosticThe ENGINE-SELF-DIAGNOSTIC object reveals current engine failures; it returns a binary string of two-byte motor, clutch, solenoid, and sensor failure codes. Additional information: The ENGINE-SELF-DIAGNOSTIC object reveals current Engine Failures; it returns a BINARY string of two-byte Motor, Clutch, Solenoid and Sensor failure codes.ro OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.1.5.7 |
engine_parameterThe ENGINE-PARAMETER object returns a device specific set of engine parameters as a binary string of byte values. It will be necessary to have a decoder for each engine to interpret the data. Additional information: The ENGINE-PARAMETER object returns a device specific set of engine parameters as a BINARY string of byte values. It will be necessary to have a decoder for each engine to interpret the data.ro OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.1.5.8 |
job OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6 |
settings_job OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.1 |
clearable_warningReturns or controls how the device will track clearable warnings. A clearable warning indicates a transient event in the device. The device will continue after the transient event occurs. If CLEARABLE-WARNING is eOff, the device does not track clearable warnings. If CLEARABLE-WARNING is eOn, all clearable warnings will be tracked until cleared (acknowledged). If CLEARABLE-WARNING is eJob, a clearable warning generated due to an event that occurs because of the print job being processed will be automatically cleared when the device has finished processing the job. Example clearable warning events include the device altering resolution or page protection due to memory constraints. The POS will document what transient events are treated as clearable warnings. Additional information: If set to eOn, the warning is displayed until the GO key is pressed or the CONTINUE object is set. If set to eJob, the warning is displayed until the end of the job in which it was generated.rw Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.1.1 |
cancel_jobCancels the print job whose ID matches the value written to the CANCEL-JOB object. The host first learns the job ID using the CURRENT-JOB-PARSING-ID command. If the printer has completely processed the job, the printer responds with <badValue>. If the value of the CURRENT-JOB-PARSING-ID is smaller than the value written to the CANCEL-JOB object, then the printer responds with <badValue>. When read, returns the value of the last job ID what was canceled, or -1 to indicate no job has been canceled. Additional information: If the value written matches the ID of a job that is currently being canceled (for any reason), the printer responds with <noError>. LaserJet 8150 uses job ID's in the range of 0..32767. Because the ID number can wrap to zero, CURRENT-JOB-PARSING-ID may be smaller than the value written to this object; when this occurs, no error will result as long as the ID is for a currently processing job. This object is write only, so the comment in the general description stating the job ID or -1 will be returned on a read does not apply.rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.1.2 |
job_info_change_idReturns the current value of an object in the job-info sub-tree whose value has changed. Define the object identifier for the object whose value has changed as job-info.required-field.optional-field.job-id. job-info represents the OID prefix of all objects in the job-info sub-tree. Required-field represents the OID field value that follows the job-info prefix. Since some objects in the job-info sub-tree have two OID fields between the job-info prefix and the job-id, the optional-field represents the OID field between the required-field and the job-id field, if present. Using this definition, the format for the JOB-INFO-CHANGE-ID binary value can be described as follows: Bytes 0-3 : required-field Bytes 4-7 : optional-field, or all zeros if there is no optional field Bytes 8-11: Job ID. Bytes 12-n : The value of the object job-info. required-field.optional-field.job-id. All multi-byte values stored in Motorola (big-endian) format, where the most significant byte occurs first. Additional information: LaserJet 8100 will use this object to report changes to the job-info-pages-printed and job-info-state objects. The required-field (bytes 0 through 3) will designate whether the change to be reported involves the pages printed (13) or job state (15). The optional-field (bytes 4 through 7) will always be zeroes. The value-field (bytes 12 through 15) will contain the new value for pages printed or job state cast to a 32-bit integer. Note: It is possible that traps generated by this object have the same value. This is caused by the architecture of LaserJet 8100. In the LaserJet 8100 System, it is highly probable that the object value will change so rapidly that when the trap is processed, PML will read the same value twice. This is timing related and will generally be seen at the end of a job.ro OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.1.3 |
hold_job_timeoutThe time, in minutes, that the printer will wait before automatically deleting a held job. This allows the printer to automatically clean up jobs that have been forgotten (held but never released). Additional information: This only applies to temporary held jobs, i.e., HOLD=ON or PROOF. This is a global timer that only affects the jobs that are sent after it is set. A value of 0 means never delete the jobs. Setting it to an unsupported value causes the printer to substitute a value (listed below) and to return <noError> status. LaserJet 4600 supports values of 0, 60, 240, 1440, and 10080 The values are as follows: <=0 snap to 0 (disabled) >=1 and <=150 snap to 60 (60 minutes) >=151 and <=840 snap to 240 (4 hours) >=841 and <=2880 snap to 1440 (1 day) >=2881 snap to 10080 (1 week)rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.1.10 |
active_print_jobs OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.2 |
job_being_parsed OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.2.1 |
current_job_parsing_idContains the printer assigned job identification for the job currently being processed by the processing PDL sub-system. The job ID is a monotonically increasing number. The job ID may be reset to zero at power-up and may roll over to zero after reaching some maximum value. Additional information: A value of -1 is returned when the printer is not parsing a job. When data for a new job is detected, this object is updated (the job may or may not turn out to be a Null Job); however, the trap does not occur until the printer determines that it is not a Null Job. (A job is considered to be a 'null job' if it has no name or job attribute, causes no pages to be printed, and consumes MIN_JOB_SIZE (9) or fewer bytes.) A trapped value will differ from the previous value by one or more. See the Job Boundary ERS for details on what constitutes a job boundary. Some job-info- objects are created when the first data bytes are received. If the printer determines that the job is a Null Job, the job-info- objects related to the Null Job are deleted. LaserJet 8100 retains the job-info- objects for the MAX_JOBS_IN_LIST (32) most recent jobs that are not Null Jobs. The first job received after power-up will have job ID 1, and the job ID will increment to 2,147,483,647 before rolling to zero. To distinguish whether a power cycle or a rollover causes a reduction in the job ID value, the object prtGeneralConfigChanges can be watched and if it increments at the same time as the drop is observed in the value of CURRENT-JOB-PARSING-ID, then a power cycle is the most likely cause.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.2.1.1 |
job_info OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5 |
job_info_name1Contains the first part of this print job's name. The last OID field for this dynamic object contains the job ID. Additional information: The job name is the string specified by the NAME= parameter of the @PJL JOB command which allows a maximum of 80 characters. The first 40 characters are in this object and the second 40 are in job-info-name2. The symbol set is Roman-8. When jobs are nested, the value assigned to this object is the name provided by the most recent @PJL JOB NAME= command. If no name is provided, a null string is returned.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.1 |
job_info_name2Contains the second part of this print job's name. The last OID field for this dynamic object contains the job ID. Additional information: See job-info-name1.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.2 |
job_info_stageIndicates what printer sub-systems are currently processing this print job. The last OID field for this dynamic object contains the job ID. cSourceSubsystem - some of the job is in the printer I/O subsystem. cProcessingSubsystem - some of the job is in the printer imaging processing subsystem. cDestinationSubsystem - some of the job is being printed. Additional information: For LaserJet 8100, cSourceSubsystem and cProcessingSubsystem will always be set and cleared together. They are set when the beginning of the job is detected, and they are cleared when the end of the job is parsed. A non-printing job will never set cDestinationSubsystem. When a page is ready to be printed (the intermediate has been built and the page is `closed' by the personality), cDestinationSubsystem will be set even if a page of a previous job is currently being printed. cDestinationSubsystem remains set until the last page of the job has finished printing. If a page requires extensive processing and allows all the previous pages of a job to complete printing, cDestinationSubsystem will remain set until the last page of the job has finished printing.ro OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.10 |
job_info_io_sourceIndicates which I/O source, the print job was received over. The value maps to port numbering scheme supported in the DEVICE/SOURCE-SUBSYSTEM/IO/PORTS sub-tree.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.11 |
job_info_pages_processedIndicates the number of pages processed by the processing subsystem. If neither the cSourceSubsystem or the cProcessingSubsystem items are in the associated JOB-INFO-STAGE object, then this object contains the total number of pages processed for this job. The last OID field for this dynamic object contains the job ID. Additional information: This object is incremented by one when a page is processed (`closed' by the personality), regardless of the number of pages that are printed as a result of the single page processed. In other words, it does not matter how many identical copies of a page are printed or no pages may be printed if operating in silent run mode, this count is incremented exactly once. A page is considered processed when all of the input data has been processed for a page (that is, when the intermediate has been produced, and the personality has `closed' the page. At this time, the image of the page is not necessarily completely formed.)ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.12 |
job_info_pages_printedIndicates the number of pages printed by the destination subsystem. If none of the cSourceSubsystem, cProcessingSubsystem or cDestinationSubsystem items are in the associated JOB-INFO-STAGE object, then this object contains the total number of pages printed for this job. This value may increase by two each time for duplex jobs. The last OID field for this dynamic object contains the job ID. Additional information: If multiple copies of a page are printed, each copy is counted individually.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.13 |
job_info_sizeIndicates the number of bytes of data processed by the processing subsystem. If neither of the cSourceSubsystem or cProcessingSubsystem items are in the associated JOB-INFO-STAGE object, then this object contains the size of this job, in bytes. The last OID field for this dynamic object contains the job ID. Additional information: This count may be incremented by values other than one as blocks of data are processed; blocks of data (which may be as large as 2K bytes) will be processed in a varying amount of time. During the processing of a job and even when a job completes, an exact count of the number of I/O bytes processed by the job is not necessarily to be expected.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.14 |
job_info_stateIndicates the state of the job. The last OID field for this dynamic object contains the job ID. eAborted - the print job was aborted. eWaitingForResources - the print job requires resources that are not currently available. Example resources that can cause the job to wait include the print engine or PDL processor being unavailable. The print engine could be unavailable due to paper out, paper jam, staple out, stapler jam, marking agent low, output bin full, etc. The PDL processor could be unavailable due to an off-line condition. Each printer specific object specification should state which conditions cause a job to be waiting for resources and also state which objects can be retrieved by an application to determine the exact cause of a resource being unavailable. ePrinted - the job has printed. The related JOB-INFO- OUTCOME object indicates if any problems were encountered while the job was processed. eRetained - the job can be reprinted. eTerminating - the job was aborted or cancelled and is currently is terminating. eInterrupted - the job has been interrupted. The job can be continued. ePaused - the job has been paused. The job can be continuted. eCancelled - the job has been cancelled. eProcessing - the job is currently being printed normally.ro Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.15 |
job_info_outcomeIndicates if any warning or error conditions were encountered while processing the assoicated job. The last OID field for this dynamic object contains the job ID. Additional information: In LaserJet 8100, warnings and errors are not recorded in this object. Although no meaningful information can be obtained from this object, it is kept around for the compatibility needs of existing software.ro Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.19 |
job_info_outbins_usedIndicates which output bins this job has delivered printed pages to. The last OID field for this dynamic object contains the job ID. Additional information: The bins designated by this collection include the printer's own output bins as well as the `logical output bins' associated with any attached external paper handling devices. (The mapping of the physical output bins of an external paper handling device to its `logical output bins' depends on the usage mode of the device. For instance, in `mailbox mode', there is one-to-one correspondence of `logical output bins' to physical bins, whereas in `stacker mode', one `logical output bin' may map to several physical bins.) Although LaserJet 4100 and LaserJet 4550 both come with two output bins -- a face-down bin on the top of the device and a face-up bin at the back of the device -- firmware will not provide a means of selecting between the two, nor will it report which of the two gets used. For this reason, bit 0 (cOutbin1) of this collection is being used to designate both of these bins together.ro OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.20 |
job_info_physical_outbins_usedIndicates which physical output bins this job has delivered printed pages to. The last OID field for this dynamic object contains the job ID. Additional information: The output bins designated by the bits of this collection include the standard output bin(s) plus the physical bins of attached external paper handling devices. The configuration (if any) of external paper handling devices will determine the mapping of individual bits in this collection to the physical bins of the devices. For LaserJet 4100 and LaserJet 4550, the cOutbin1 is used for Face Down bin, cOutbin2 is used for Face Up bin, and 3-15 are used for the 13 optional output bins (12 plus an extension to the Face Up bin) for backwards compatibility with LaserJet 8000/LaserJet 8100 and forwards compatibility with LaserJet 8150. However, since they cannot distinguish output going to the Face Up or Face Down bin in the firmware because the diverter can only be moved manually, bit 0 (cOutbin1) is being used to designate both of these bits together. If an external paper handling output device is connected, then bit 2 (cOutbin3) will represent the device's first output bin (and so on).ro OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.22 |
job_info_attribute OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23 |
job_info_attr_1Returns the value that was set in PJL via the SET JOBATTR= command. Attribute objects are saved sequentially, starting with 1, after the start of a job. If more attributes are set than there are objects to store them, the excess JOBATTR values are ignored. If the corresponding SET JOBATTR= command has not been received when a get is done for this object, a status of <noSuchName> will be returned.ro OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.1 |
job_info_attr_2Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.ro OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.2 |
job_info_attr_3Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.ro OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.3 |
job_info_attr_4Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.ro OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.4 |
job_info_attr_5Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.ro OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.5 |
job_info_attr_6Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.ro OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.6 |
job_info_attr_7Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.ro OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.7 |
job_info_attr_8Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.ro OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.8 |
job_info_attr_9Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.ro OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.9 |
job_info_attr_10Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.ro OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.10 |
job_info_attr_11Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.ro OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.11 |
job_info_attr_12Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.ro OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.12 |
job_info_attr_13Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.ro OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.13 |
job_info_attr_14Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.ro OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.14 |
job_info_attr_15Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.ro OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.15 |
job_info_attr_16Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.ro OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.16 |
job_info_requested_originalsThe number of requested collated copies. The value was supplied with the job via PJL QTY variable, the PostScript Collate and NumCopies entries in the page device dictionary, or via some other mechansim.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.24 |
job_info_page_count_current_originalThe page number being printed within the current copy of a collated multi-copy job. This value changes when the job-info-pages-printed changes. The job-info-pages-printed indicates the total number of pages printed in the job, while this object indicates the number of pages printed for this copy of a collated multi-copy job. Additional information: The number of pages in the current copy of a collated multi-copy job which have been completely printed and safely delivered to the output bin.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.25 |
job_info_pages_in_originalNumber of pages in a single copy of a collated multi-copy job.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.26 |
job_info_printed_originalsNumber of collated copies completely printed and delivered to the output bin at time of query.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.27 |
job_info_accounting OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.28 |
job_info_accounting_media_sizeContains the media size of the printed job. The media size of the first page will decide the media size of the entire job. The return value of this object will only be valid when the printer finishes printing the entire job.ro Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.28.1 |
job_info_accounting_media_typeContains the media type of the printed job. The media type of the first page will decide the media type of the entire job. The return value of this object will only be valid when the printer finishes printing the entire job.ro Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.28.2 |
job_info_accounting_finishing_optionsContains the finishing option used on the printed job. The finishing option specified for the first page will decide the finishing option of the entire job. The return value of this object will only be valid when the printer finishes printing the entire job.ro Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.28.3 |
job_info_accounting_media_simplex_countContains the total number of simplex pages printed in a particular job.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.28.4 |
job_info_accounting_media_duplex_countContains the total number of duplex pages printed in a particular job.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.28.5 |
job_info_accounting_grayscale_impression_countContains the total number of monochrome pages printed in a particular job.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.28.6 |
job_info_accounting_color_impression_countContains the total number of color pages printed in a particular job.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.28.7 |
job_info_accounting_black_dotsContains the total number of black pixels used in a particular job.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.28.8 |
job_info_accounting_yellow_dotsContains the total number of yellow pixels used in a particular job.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.28.9 |
job_info_accounting_cyan_dotsContains the total number of cyan pixels used in a particular job.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.28.10 |
job_info_accounting_magenta_dotsContains the total number of magenta pixels used in a particular job.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.28.11 |
job_info_accounting_job_typeKeeps track of what type of job is processed.ro Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.28.14 |
held_job OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.7 |
held_job_info OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.7.1 |
held_job_user_nameUser name that is obtained by the driver through some internal method or from user input. Additional information: The following is a general description for all the JOB-MANAGEMENT objects described below. These object describe the attributes of the dynamic list containing all the stored jobs on the disk available for printing or deleting via the job-management feature. The jobs on this list are not deleted from the disk unless explicitly specified by the user. A print job may be specified for retention by PJL commands in the data stream. Following is a list of the PJL commands (i.e. these comments describe the PJL implementation and in some cases do not reflect the PML implementation.): @PJL SET HOLD=OFF|ON|PROOF|STORE|PRINT GENERAL DESCRIPTION: This variable specifies the retention classification of the job. The values indicate whether the job is printed immediately and/or stored. OFF: The job is printed but not retained on disk after printing. This is the default value. ON: This setting may be thought of as free proof-and-hold. The requested number of copies will be printed and the job will be temporarily stored on disk. The job will then be available for printing additional copies through the control panel and through PML. There will be a limit to the number of these temporary jobs that may be stored, and when the limit is exceeded the oldest job will be removed from the disk. PROOF: One copy of the job is printed and remaining copies are stored on disk. The job is then available to select for printing via the control panel menus or PML. The job will be deleted from the disk when the disk space is needed for another proof and hold job but only after the additional copies have been printed. It will also be deleted when the user sends down another proof and hold job with the same job name, or the user explicitly deletes the job. STORE: The job is not printed immediately but is retained on disk. The job is available to select for printing via the control panel DEFAULT VALUE: OFF The value will be stored in RAM only, not in NVRAM. The legal PJL commands are SET and INQUIRE. DEFAULT is not allowed. The variable will appear in the PJL INFO VARIABLES list. @PJL SET USERNAME=<80 bytes> GENERAL DESCRIPTION: Eighty-character user name that is obtained by the driver through some internal method or from user input. If the job stream does not contain a USERNAME the default value will be NO USER NAME. The driver is responsible for determining the size of the printers control panel and sending a string of appropriate length. DEFAULT VALUE: NO USER NAME The value will be stored in RAM only, not in NVRAM. The legal PJL commands are SET and, INQUIRE. DEFAULT is not allowed. The variable will appear in the PJL INFO VARIABLES list. @PJL SET JOBNAME=<80 bytes> GENERAL DESCRIPTION: Eighty-character job name that may be generated by the driver or obtained from user input. This value may be used in conjunction with the USERNAME to select a job from the front panel. If the job stream does not contain a JOBNAME, the printer will assume no job name; each subsequent job that is sent down by the same user would replace the users last job on disk. The driver is responsible for determining the size of the printers control panel and sending a string of appropriate length. NOTE: The limit of 80 bytes is a PJL limit. The limit for PML will be 40 bytes. DEFAULT VALUE: NULL STRING The value will be stored in RAM only, not in NVRAM. The legal PJL commands are SET and INQUIRE. DEFAULT is not allowed. The variable will appear in the PJL INFO VARIABLES list. @PJL SET HOLDTYPE=PUBLIC|PRIVATE GENERAL DESCRIPTION: This variable specifies the privacy level of the job. PUBLIC: The job does not require a PIN in order to be released for printing. This is the default value. PRIVATE: The job requires a PIN in order to be released for printing. The PIN is specified by the HOLDKEY variable. If the HOLDTYPE is set to PRIVATE, a HOLDKEY value must be specified. If no HOLDKEY is specified, the job will be considered PUBLIC. DEFAULT VALUE: PUBLIC The value will be stored in RAM only, not in NVRAM. The legal PJL commands are SET and INQUIRE. DEFAULT is not allowed. The variable will appear in the PJL INFO VARIABLES list. @PJL SET HOLDKEY=4 digits, 0000...9999 GENERAL DESCRIPTION: A 4-digit string, each digit 0-9, that is specified in the job stream and then required to be entered in order to release the job for printing. If a HOLDTYPE is PRIVATE, a HOLDKEY value must be specified. If no HOLDKEY value is specified, a job will be considered PUBLIC. DEFAULT VALUE: NULL STRING The value will be stored in RAM only, not in NVRAM. The legal PJL commands are SET and INQUIRE. DEFAULT is not allowed. The variable will appear in the PJL INFO VARIABLES list. The format for the OID is as follows: 3.4.1.6.x.y <-----> | | | | \ / | job-id in the system / \ PML_JOB_MGNT_ROOT_OID \ job attribute 1..6 x values are 1..6: 1) user-name: user name that is obtained by the driver through some internal method or from user input. 2) job-name: job name may be generated by the driver or obtained from user input. 3) hold: indicates the retention classification of the job. The values indicate whether the job is printed immediately and/or stored. There are 4 options: OFF: The job is printed but not retained on the disk. ON: The job is printed and stored temporarily on the disk. STORE: The job is not printed but stored on the disk. PROOF: One copy of the job is printed and the remaining copies are stored on the disk. 4) holdtype: The variable specifies the security level of the job. PUBLIC: The job does not require a PIN in order to release the job for printing. PRIVATE: The job requires a PIN in order to be released for printing. 5) quantity: number of copies to print. Valid values are 0..999. 6) pin: A 4 digit string, each digit is 0-9, that is specified in the job stream and then required to be entered in order to release the job for printing. y : an unsigned 32-bit number which uniquely identifies the job. The job id for the job remains the same for the job until it is deleted from the held jobs list. For example, the OID below is asking for the user name of the job whose id is 3. The application would issue: OID get 3.4.1.6.1.3 For example, the <getnext> OID values sequence is as follows: OID returned OID getnext 3.4.1.6 3.4.1.6.1.1 getnext 3.4.1.6.1.1 3.4.1.6.1.2 getnext 3.4.1.6.2.1 3.4.1.6.2.2 *** getnext 3.4.1.6.1.6 3.4.1.6.1.7 getnext 3.4.1.6.2.1 3.4.1.6.2.2 getnext 3.4.1.6.5.2828 3.4.1.6.6.1 NOTE: for example above, job id 2828 is the last job in the list of held jobs. *** Also supported is <getnext> on the job attributes: OID returned OID getnext 3.4.1.6.1 3.4.1.6.1.1 getnext 3.4.1.6.6 3.4.1.6.6.1ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.7.1.1 |
held_job_job_nameThe job name may be generated by the driver or obtained from user input.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.7.1.2 |
held_job_retentionIndicates the retention classification of the job. The values indicate whether the job is printed immediately or stored. There are 4 options: eHoldOff: The job is printed but not retained on the disk. eHoldOn: The job is printed and stored temporarily on the disk. eHoldStore: The job is not printed but stored on the disk. eHoldProof: One copy of the job is printed and the remaining copies are stored on the disk.ro Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.7.1.3 |
held_job_securityThe variable specifies the security level of the job. eHoldTypePublic: The job does not require a PIN in order to release the job for printing. eHoldTypePrivate: The job requires a PIN in order to be released for printing.ro Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.7.1.4 |
held_job_quantityNumber of copies to print.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.7.1.5 |
held_job_pinA string that is specified in the job stream and then required to be entered in order to release the job for printing. PIN stands for Personal Identification Number. Additional information: Must be a 4 digit string, each digit must be 0..9 or a null string if there is no pin. For security purposes, you can no longer get the value of the PIN.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.7.1.6 |
held_job_control OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.7.2 |
held_job_printInstructs the printer to schedule the specified held job for printing with the specified number of copies. The job-id is used to identify which job to print. A held job can also be printed from the control panel. Additional information: Bytes 0-3 is the job id of the job to print. Bytes 4-7 is the number of copies to print. Bytes 8-11 (optional) contain the PIN for a Private job.rw OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.7.2.1 |
held_job_deleteInstructs the printer to delete the specified held job from the list. The job-id is used to identify which job to delete. A held job can also be deleted from the control panel. Additional information: Setting this to a value that is not a Held Job on the system or is a Private Held Job returns <ErrUnsupValue>. To delete a private Held Job, you must use the PML object HELD-JOB-PRINT with a quantity of 0 and supply the correct HELD-JOB-PIN with the request. (See HELD-JOB-PRINT)rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.7.2.2 |
held_job_set_queue_sizeSets the maximum number of jobs which can be stored in the held job list. Additional information: Sets the size of the temporary job lists queue.rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.7.2.3 |
held_job_enableEnables or disables Job Retention (Job Hold). The valid values are eDisabled and eEnabled. (Specifying an invalid mode causes an <badValue> error to be returned.) When eDisabled is specified all Job Retention (Hold, Proof, Store, PIN Printing) is disabled. When eEnabled is specified, the Job Retention characteristics of a given job are defined by the PJL variable SET HOLD. Additional information: When disabled, held jobs are not removed, but must be explicitly removed through the Control Panel or the PML object HELD-JOB-DELETE.rw Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.7.2.4 |
file_system OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.10 |
settings_file_system OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.1 |
file_system_max_open_filesThe number of open files allowed at one time. Opening a file when the maximum number of files are currently open will fail. Additional information: Indicates the number of open files a personality (e.g. PCL or PostScript) is guaranteed to be able to open before the file system runs out of file handles. This object is between 1 and 500. Returns <noSuchName> status if attempting to access this object and there is no storage device is installed.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.1.2 |
file_system_set_system_partition_writeableThis object allows the system partition to be written to. It consists of a C structure containing the following fields: typedef struct { ubyte password[8]; ubyte volumenumber; } fs_writeable_system_partition_t; which is described below: Bytes 0 - 7: contain the password Byte 8 : is the volume number Access to this command is controlled by the password. If the password supplied is incorrect the command will fail. The volumenumber is a volume number of an existing system partition. Additional information: Returns <noSuchName> status if attempting to access this object and there is no storage device is installed. Returns <badValue> if the password is incorrect or if the volume requested is not present.rw OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.1.6 |
file_system_set_system_partition_readonlyChanges a system partition to be READ-ONLY. The value is the volume number to change. If the volume number specified is NOT a system partition an error is returned. Additional information: Returns <noSuchName> status if attempting to access this object and there is no storage device is installed. Returns <badValue> if the volume requested is not present.rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.1.7 |
file_system_delete_filesSetting this object causes the specified filename to be deleted, after first validating that the authentication data is correct for the specified user ID. The format for this object is a C structure: typedef struct { sint32 UserId; uint16 AuthenticationDataLen ubyte AuthenticationData[] char Filename[]; } fs_delete_files_t; which is described below: Bytes 0 - 3: contains a user id represented as a multi-byte value that is stored in big-endian format, where the most significant byte occurs first. Bytes 4 - 5 : Length of the Athentication data that follows starting at offset 6. Stored as a multi-byte value that is stored in big-endian format, where the most significant byte occurs first. Bytes 6 - 6+AuthenticationDataLen : a ubyte array containing the Authentication data used to verify access for this operation. Bytes starting at offset (6+AuthenticationDataLen+1): A null terminated character array representing the ASCII file name to be deleted. The length of the string will be limited by the remaining space in the object. This string represents a fully-qualified path name which may specify a filename or a regular expression that may match multiple files (e.g <path>/*.exe). Access to this command is controlled by the UserId and the authentication data. If the UserID or authentication data supplied is incorrect the command will fail. The device POS will specify any limitations to the length of the filename string, what constitutes a correct user ID, what constitutes correct authentication data, and the significance of any return values. Additional information: Setting this object causes the specified filename to be deleted, after first validating that the authentication data is correct for the specified user ID. This object is always present. The format for this object is a C structure: typedef struct { sint32 UserId; uint16 AuthenticationDataLen ubyte AuthenticationData[] char Filename[]; } fs_delete_files_t; Bytes 0 - 3: contains a user id represented as a multi-byte value that is stored in big-endian format, where the most significant byte occurs first. Bytes 4 - 5 : Length of the authentication data that follows starting at offset 6. Stored as a multi-byte value that is stored in big-endian format, where the most significant byte occurs first. Bytes 6 - 6+AuthenticationDataLen : a ubyte array containing the authentication data used to verify access for this operation. Bytes starting at offset (6+AuthenticationDataLen+1): A null terminated character array representing the ASCII file name to be deleted. The length of the string will be limited by the remaining space in the object. This string represents a fully-qualified path name which may specify a filename or a file-type regular expression that may match multiple files (e.g., <path>/*.exe). Access to this command is controlled by the UserId and the authentication data. If the UserID or authentication data supplied is incorrect the command will fail. The device POS will specify any limitations to the length of the filename string, what constitutes a correct user ID, what constitutes correct authentication data, and the significance of any return values.rw OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.1.8 |
file_systems OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.3 |
file_system2 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.3.2 |
file_system2_initialize_volumeSetting this object to eInitializing causes file system 2 to be initialized. Reading this object indicates if the file system is currently being initialized. Additional information: The hrDeviceIndex value for the mass storage device is the same value that is used to index into the FILE-SYSTEM sub-tree. Since this product supports up to 3 physical mass storage device, and since the hrDeviceIndex for the mass storage devices will start at 2 if the mass storage device is installed, the FILE-SYSTEM2-INITIALIZE-VOLUME object will be the object that allows the mass storage device to be initialized that is the 1st device.rw Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.3.2.6 |
file_system3 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.3.3 |
file_system3_initialize_volumeSetting this object to eInitializing causes file system 3 to be initialized. Reading this object indicates if the file system is currently being initialized. Additional information: The hrDeviceIndex value for the mass storage device is the same value that is used to index into the FILE-SYSTEM sub-tree. Since this product supports up to 3 physical mass storage device, and since the hrDeviceIndex for the mass storage devices will start at 2 if the mass storage device is installed, the FILE-SYSTEM3-INITIALIZE-VOLUME object will be the object that allows the mass storage device to be initialized that is the 2nd device.rw Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.3.3.6 |
file_system4 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.3.4 |
file_system4_initialize_volumeSetting this object to eInitializing causes file system 4 to be initialized. Reading this object indicates if the file system is currently being initialized. Additional information: The hrDeviceIndex value for the mass storage device is the same value that is used to index into the FILE-SYSTEM sub-tree. Since this product supports up to 3 physical mass storage devices, and since the hrDeviceIndex for the mass storage devices will start at 2 if the mass storage device is installed, the FILE-SYSTEM4-INITIALIZE-VOLUME object will be the object that allows the mass storage device to be initialized that is the 3rd device.rw Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.3.4.6 |
errorlog OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11 |
error1 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.1 |
error1_time_stampContains some sort of time stamp indicating when error 1 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: This item contains the engine page count when the error occurred. If there is currently no error entry for this object, a '0' will be returned. Note that '0' may also be returned when there is a valid error, but a current page count was unavailable. If ERROR1-CODE object also returns '0', then an error has not yet been logged for this object. See ERROR1-CODE for an explanation of the order used for storing errors.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.1.1 |
error1_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: Returns a device specific error code. If the error code returned is '0', then the printer has not yet logged an error for this object. When the maximum number of errors is reached (30 on LaserJet printers), and a new error occurs, the error in ERROR1-CODE will be replaced by the one in ERROR2-CODE, and so on until the last error object will be given the value of the new error. The error number is returned in the upper 16 bits. If it is 68, 69, 79, or 80, then the sub code is returned in the lower 16 bits (eg. 68 001C, where the subcode is already a hexadecimal value). If the error number is any other number, then the 1st sub code (XX) will be in bits 15-8 and the 2nd sub code (YY) will be in bits 7-0 (eg. 55.04.02) where XX=04 and YY=02). See the Control Panel ERS for specific information about the meaning of each code. Example: If the error is 68 001A, then the value returned will be 4456474. To break it down: 4456474 = 0x0044001A The upper 16 bits: 0x0044 = 68 The lower 16 bits: 0x001A = 001A Which is the error: 68 001A Example: If the error is 55.04.241, then the error code will be 3605745. To break it down: 3605745 = 0x003704F1 The upper 16 bits: 0x0037 = 55 The upper byte of the lower 16 bits: 0x04 = 04 The lower byte of the lower 16 bits: 0xF1 = 241 Which is the error: 55.04.241ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.1.2 |
error2 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.2 |
error2_time_stampContains some sort of time stamp indicating when error 2 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.2.1 |
error2_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.2.2 |
error3 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.3 |
error3_time_stampContains some sort of time stamp indicating when error 3 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.3.1 |
error3_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.3.2 |
error4 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.4 |
error4_time_stampContains some sort of time stamp indicating when error 4 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.4.1 |
error4_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.4.2 |
error5 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.5 |
error5_time_stampContains some sort of time stamp indicating when error 5 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.5.1 |
error5_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.5.2 |
error6 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.6 |
error6_time_stampContains some sort of time stamp indicating when error 6 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.6.1 |
error6_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.6.2 |
error7 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.7 |
error7_time_stampContains some sort of time stamp indicating when error 7 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.7.1 |
error7_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.7.2 |
error8 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.8 |
error8_time_stampContains some sort of time stamp indicating when error 8 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.8.1 |
error8_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.8.2 |
error9 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.9 |
error9_time_stampContains some sort of time stamp indicating when error 9 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.9.1 |
error9_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.9.2 |
error10 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.10 |
error10_time_stampContains some sort of time stamp indicating when error 10 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.10.1 |
error10_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.10.2 |
error11 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.11 |
error11_time_stampContains some sort of time stamp indicating when error 11 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.11.1 |
error11_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.11.2 |
error12 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.12 |
error12_time_stampContains some sort of time stamp indicating when error 12 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.12.1 |
error12_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.12.2 |
error13 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.13 |
error13_time_stampContains some sort of time stamp indicating when error 13 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.13.1 |
error13_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.13.2 |
error14 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.14 |
error14_time_stampContains some sort of time stamp indicating when error 14 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.14.1 |
error14_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.14.2 |
error15 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.15 |
error15_time_stampContains some sort of time stamp indicating when error 15 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.15.1 |
error15_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.15.2 |
error16 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.16 |
error16_time_stampContains some sort of time stamp indicating when error 16 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.16.1 |
error16_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.16.2 |
error17 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.17 |
error17_time_stampContains some sort of time stamp indicating when error 17 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.17.1 |
error17_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.17.2 |
error18 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.18 |
error18_time_stampContains some sort of time stamp indicating when error 18 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.18.1 |
error18_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.18.2 |
error19 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.19 |
error19_time_stampContains some sort of time stamp indicating when error 19 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.19.1 |
error19_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.19.2 |
error20 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.20 |
error20_time_stampContains some sort of time stamp indicating when error 20 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.20.1 |
error20_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.20.2 |
error21 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.21 |
error21_time_stampContains some sort of time stamp indicating when error 21 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.21.1 |
error21_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.21.2 |
error22 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.22 |
error22_time_stampContains some sort of time stamp indicating when error 22 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.22.1 |
error22_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.22.2 |
error23 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.23 |
error23_time_stampContains some sort of time stamp indicating when error 23 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.23.1 |
error23_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.23.2 |
error24 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.24 |
error24_time_stampContains some sort of time stamp indicating when error 24 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.24.1 |
error24_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.24.2 |
error25 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.25 |
error25_time_stampContains some sort of time stamp indicating when error 25 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.25.1 |
error25_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.25.2 |
error26 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.26 |
error26_time_stampContains some sort of time stamp indicating when error 26 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.26.1 |
error26_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.26.2 |
error27 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.27 |
error27_time_stampContains some sort of time stamp indicating when error 27 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.27.1 |
error27_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.27.2 |
error28 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.28 |
error28_time_stampContains some sort of time stamp indicating when error 28 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.28.1 |
error28_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.28.2 |
error29 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.29 |
error29_time_stampContains some sort of time stamp indicating when error 29 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.29.1 |
error29_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.29.2 |
error30 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.30 |
error30_time_stampContains some sort of time stamp indicating when error 30 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.30.1 |
error30_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.30.2 |
error31 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.31 |
error31_time_stampContains some sort of time stamp indicating when error 31 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.31.1 |
error31_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.31.2 |
error32 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.32 |
error32_time_stampContains some sort of time stamp indicating when error 32 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.32.1 |
error32_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.32.2 |
error33 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.33 |
error33_time_stampContains some sort of time stamp indicating when error 33 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.33.1 |
error33_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.33.2 |
error34 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.34 |
error34_time_stampContains some sort of time stamp indicating when error 34 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.34.1 |
error34_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.34.2 |
error35 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.35 |
error35_time_stampContains some sort of time stamp indicating when error 35 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.35.1 |
error35_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.35.2 |
error36 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.36 |
error36_time_stampContains some sort of time stamp indicating when error 36 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.36.1 |
error36_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.36.2 |
error37 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.37 |
error37_time_stampContains some sort of time stamp indicating when error 37 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.37.1 |
error37_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.37.2 |
error38 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.38 |
error38_time_stampContains some sort of time stamp indicating when error 38 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.38.1 |
error38_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.38.2 |
error39 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.39 |
error39_time_stampContains some sort of time stamp indicating when error 39 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.39.1 |
error39_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.39.2 |
error40 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.40 |
error40_time_stampContains some sort of time stamp indicating when error 40 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.40.1 |
error40_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.40.2 |
error41 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.41 |
error41_time_stampContains some sort of time stamp indicating when error 41 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.41.1 |
error41_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.41.2 |
error42 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.42 |
error42_time_stampContains some sort of time stamp indicating when error 42 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.42.1 |
error42_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.42.2 |
error43 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.43 |
error43_time_stampContains some sort of time stamp indicating when error 43 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.43.1 |
error43_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.43.2 |
error44 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.44 |
error44_time_stampContains some sort of time stamp indicating when error 44 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.44.1 |
error44_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.44.2 |
error45 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.45 |
error45_time_stampContains some sort of time stamp indicating when error 45 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.45.1 |
error45_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.45.2 |
error46 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.46 |
error46_time_stampContains some sort of time stamp indicating when error 46 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.46.1 |
error46_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.46.2 |
error47 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.47 |
error47_time_stampContains some sort of time stamp indicating when error 47 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.47.1 |
error47_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.47.2 |
error48 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.48 |
error48_time_stampContains some sort of time stamp indicating when error 48 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.48.1 |
error48_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.48.2 |
error49 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.49 |
error49_time_stampContains some sort of time stamp indicating when error 49 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.49.1 |
error49_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.49.2 |
error50 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.50 |
error50_time_stampContains some sort of time stamp indicating when error 50 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.50.1 |
error50_codeContains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.50.2 |
resource_manager OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.12 |
mass_storage_resources OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.12.3 |
mass_storage_resource_change_counterA counter which changes when a mass storage based resource has been added or deleted. Additional information: The value of this counter changes each time the MASS-STORAGE-RESOURCE-CHANGED object is set to eTrue. The value also changes when the mass storage device is initialized. However, the value does not change when a mass storage device is removed and a different mass storage device is installed. Initializing all volumes sets this object back to the factory default value. A reboot sets this object back to the factory devalut value. Returns <noSuchName> status if attempting to access this object and there is no storage device is installed.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.12.3.1 |
mass_storage_resource_changedSetting to eTrue causes MASS-STORAGE-RESOURCE-CHANGE-COUNTER to be incremented. Additional information: Returns <noSuchName> status if attempting to access this object and there is no storage device is installed.rw Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.12.3.2 |
remote_procedure_call OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.13 |
settings_rpc OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.1 |
rpc_bind_protocol_addressArray of Berkeley sockets style protocol addresses used to bind RPC to a communications protocol family. Setting an instance of this array object to a zero length binary value disables the transport protocol indicated by that instance. All multi-bytes fields are in network (or big-endian) order. Bytes 1 and 2 indicate the transport protocol. Some of the transport protocol mapping information can be found in RFC 1010 Assigned Numbers. A list of interesting transport protocol number mappings include: <table> Protocol | Number ---------+------- UDP/IP | 17 IPX | 1000 MLC | 4660 </table> Bytes 3 and 4 indicate the address family. The address family uses the same mapping as the BSD sockets address family. A list of interesting address family mappings include: <table> Address Family | Number ---------------+------- Internet | 2 NetWare | 6 MLC | 22136 </table> The format the fifth and following bytes is dependent on the address family. For the Internet address family, bytes 5 and 6 contain the port number, bytes 7 through 10 contain the IP address, and the following eight bytes are unused. For NetWare, bytes 5 through 8 are the network number, bytes 9 through 14 are the node number, and bytes 15 and 16 are the socket number. Additional information: The length of the binary value is zero if the instance of an object in the rpc-bind-protocol-address array is not in use. Returns <noSuchName> status if attempting to access this object and there is no storage device is installed.ro OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.1.2 |
status_rpc OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.2 |
rpc_bound_protocol_addressAn array of Berkeley sockets style protocol addresses that the NFS service has been bound to successful. The format is that same as the array of RPC-BIND-PROTOCOL-ADDRESS of objects. Additional information: Returns <noSuchName> status if attempting to access this object and there is no storage device is installed.ro OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.2.3 |
mass_storage_block_driver OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.15 |
settings_mass_storage_bd OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.15.1 |
ram_disk_modeReturns or controls RAM disk support. eOFF turns off the RAM disk functionality. eOn turns on the RAM disk functionality and creates a RAM disk whose size is controlled by the RAM-DISK-SIZE object. eAuto turns on the RAM disk functionality and creates a RAM disk size determined by the printer based on installed options and other memory related settings. Additional information: Returns or controls RAM disk support. eOFF turns off the RAM disk functionality. eAuto turns on the RAM disk functionality and creates a RAM disk size determined by the printer based on the amount of installed memory.rw Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.15.1.1 |
ram_disk_sizeReturns or controls the size of the RAM disk. The device POS specifies the minimum memory requirements. The object MAXIMUM-RAM-DISK-MEMORY specifies the maximum memory available for the RAM disk. Additional information: Returns the size of the RAM disk.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.15.1.2 |
status_mass_storage_bd OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.15.2 |
maximum_ram_disk_memoryThis object's name is misleading. This object does not return the maximum configurable RAM disk size. Instead, it returns the maximum amount of memory, in bytes, that can used to increase the size of the RAM disk. Additional information: This object returns the maximum amount of additional memory that is available for increasing the size of the RAM disk.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.15.2.1 |
accounting OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.16 |
printer_accounting OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1 |
printed_media_usage OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.1 |
printed_media_simplex_countTotal number of simplex pages printed in this media size. Additional information: The 5 usage (simplex/duplex count, simplex/duplex click charge and paper size total) objects described here and below detail the usage for the printer for each paper size defined in the PCL Implementor's Guide and in the Media Size Table in the hpmib.txt. The OID binding is based on the click attribute and paper size. For example: The format for the OID is as follows: 3.4.1.5.x.y <-----> | | | | \ / | paper size / \ PRINTER-CLICK_TOTALS ROOT \ OID click attribute 1..5 x values are 1..5: 1) simplex count 2) simplex click charge 3) duplex count 4) duplex click charge 5) printer or scanner paper size total (i.e. depends if the root OID is referrring to the printer or scanner). y : paper size as defined in the Media Size Table in the hpmib.txtro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.1.1 |
printed_media_simplex_chargeCharge for each simplex page printed in this media size.rw OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.1.2 |
printed_media_duplex_countTotal number of duplex pages printed in this media size.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.1.3 |
printed_media_duplex_chargeCharge for each duplex page printed in this media size. Additional information: The click charges for duplex printed media.rw OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.1.4 |
printed_media_total_chargeThe total charge for pages printed in this media size.ro OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.1.5 |
printed_media_maximum_pixels_per_pageThe number of pixels required to completely fill a page of this media size. The device POS will specify the resolution at which this pixel count was calculated. Additional information: The number of pixels required to fill a page of a specific media size. The OID binding is the media size you to query for. Only media sizes which the printer supports will be available.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.1.6 |
printed_media_combined_totalTotal number of letter equivalently weighted pages both color and mono combined with this printer. Additional information: The combined total per page size of simplex and duplex color pages plus simplex and duplex mono pages.ro OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.1.7 |
usage_printer_total_chargeTotal printer charge for all paper sizes printed.ro OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.2 |
usage_average_toner_coverageReports the average toner area coverage of all pages printed over the life of the device. Counts pixels on each page, divides pixel count by pixels possible on a page to give the percentage of coverage, and keeps a rolling average percent weighted by area printed.ro OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.3 |
usage_staple_countTotal number of staples used.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.4 |
usage_instructions_line1The first line of usage instructions for the device user.Appears on Line 1 of the usage page.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.5 |
usage_instructions_line2The second line of usage instructions for the device user.Appears on Line 1 of the usage page.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.6 |
usage_instructions_line3The third line of usage instructions for the device user.Appears on Line 1 of the usage page.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.7 |
usage_instructions_line4The fourth line of usage instructions for the device user.Appears on Line 1 of the usage page.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.8 |
printed_modes_usage_totalThis object reports the total color and mono print modes usage for the life of the printer. This value is reported on the usage page.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.9 |
source_tray_usage_totalThis object reports the total source tray usage for the life of the printer. This value is reported on the usage page.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.10 |
destination_bin_usage_totalThis object reports the total destination bin usage for the life of the printer. This value is reported on the usage page.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.11 |
usage_printer_mono_total_chargeTotal printer charge for all paper sizes printed in monochrome only. Additional information: This is the total charge over the range of all supported media sizes for duplex and simplex mono pages.ro OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.12 |
usage_printer_color_total_chargeTotal printer charge for all paper sizes printed in color only. Additional information: This is the total charge over the range of all supported media sizes for duplex and simplex color pages.ro OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.13 |
printer_color_accounting OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.3 |
printed_media_color_usage OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.3.1 |
printed_media_color_simplex_countTotal number of color simplex pages printed in this media size.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.3.1.1 |
printed_media_color_duplex_countTotal number of color duplex pages printed in this media size.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.3.1.3 |
printed_media_color_total_countThe total count for color pages printed in this media size.ro OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.3.1.5 |
printed_modes_accounting OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.4 |
printed_modes_usage OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.4.1 |
printed_modes_mono_countTotal number of mono pages printed in this fuser mode.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.4.1.1 |
printed_modes_color_countTotal number of color pages printed in this fuser mode.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.4.1.3 |
printed_modes_total_countThe total count for pages printed in this fuser mode.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.4.1.5 |
source_tray_accounting OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.5 |
source_tray_usage OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.5.1 |
source_tray_usage_countTotal number of pages printed from this source tray.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.5.1.1 |
destination_bin_accounting OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.6 |
destination_bin_usage OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.6.1 |
destination_bin_usage_countTotal number of pages printed to this destination bin.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.6.1.1 |
firmware_download OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.18 |
firmware_download_write_status_supportedThis object provides information on whether the printer has the ability to communicate the write-status of the firmware download while the download is taking place.ro Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.18.1 |
firmware_download_write_timeIf the design of the firmware-download implementation does not allow PML interaction during the download process, this value provides an estimation of the time where the printer will not be able to engage in PML communication. Additional information: If the design of the firmware-download implementation does not allow PML interaction during the download process, this value provides an estimation of the time where the printer will not be able to engage in PML communication. The calculated time is expected to be 140 secs. However, this time may increase as high as 280 secs as the flash part nears the maximum flash count.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.18.2 |
firmware_download_write_countTells the number of times that firmware has been downloaded to the flash part. Additional information: Tells the number of times that firmware has been downloaded to the flash part. The default value will vary depending on how many times the firmware is rolled before shipping.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.18.3 |
firmware_download_current_stateProvides the current or last reportable state of the firmware download process. The current state may not necessarily be the current state, but could be the post-mortem state.rw Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.18.4 |
firmware_download_maximum_write_countReports the manufacturer specified number of times that firmware can be downloaded to the flash part. A value of -1 means that there is no limit. A value of 0 means that downloading firmware is not permitted by this part. Any other positive integer value corresponds to the number of times that firmware can be downloaded to the flash part. Additional information: Reports the manufacturer specified number of times that firmware can be downloaded to the flash part. A value of -1 means that there is no limit. A value of 0 means that downloading firmware is not permitted by this part. Any other positive integer value corresponds to the number of times that firmware can be downloaded to the flash part. The current maximum write count is 500. This may change as flash technology evolves.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.18.5 |
firmware_download_nameThis returns the name of the printer. This should match the name in the header of the upgrade image being sent to the flash part. If the name does not match with the name returned then the image that we are attempting to download does not upgrade the printer firmware. Additional information: This object returns the HP name of the printer. This should match what is in the PJL header of the RFU job Web Jet Admin uses this to ensure the printer is available to be upgraded.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.1.18.6 |
firmware_download_versionThis object will return a string value representing the current revision of firmware that the printer is operating with. This is used to determine if code needs to be upgraded when an firmware bundle comes in, in an upgrade job. Additional information: Web Jet Admin uses the version string that is returned to determine what peices of an RFU bundle need to be upgraded when an RFU job is being built. This objects will return the version string of the printer.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.1.18.7 |
operating_system OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.19 |
os_execute_fileThis object's input is a null-terminated string representing a fully-qualified path name for an executable file. This object causes the file to be executed by the OS. Additional information: This object's input is a null-terminated string of two or more whitespace-separated tokens. The first token is a path to a directory to make the current working directory. The second token is a path to an executable file to be executed. Any remaining whitespace-separated tokens are optional and will be passed as parameters to the executable. The paths to the directory and executable can be either PJL style (e.g., 1:\app\example) or UNIX-style (e.g., /hpmnt/dsk_ide1a/app/example). The executable is run in a separate process.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.1.19.1 |
upgradable_devices OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.20 |
upgradable_devices_write_status_supportedThis object provides information on whether the upgradable device has the ability to communicate the write-status of the upgrade while the upgrade is taking place.ro Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.20.1 |
upgradable_devices_write_timeIf the design of the device upgrade implementation does not allow PML interaction during the download process, this value provides an estimation of the time where the device will not be able to engage in PML communication. The time returned will depend upon what device is attempting to be upgraded.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.20.2 |
upgradable_devices_write_countTells the number of times that firmware for device X has been downloaded to the flash part. The default value will vary depending on how many times the firmware is rolled before shipping.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.20.3 |
upgradable_devices_current_stateProvides the current or last reportable state of the device upgrade process. The current state may not necessarily be the current state, but could be the post-mortem state.ro Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.20.4 |
upgradable_devices_max_write_countReports the manufacturer specified number of times that firmware for device X can be downloaded to the flash part. A value of -1 means that there is no limit. A value of 0 means that downloading firmware is not permitted by this part. Any other positive integer value corresponds to the number of times that the firmware for device X can be downloaded to the flash part. The current maximum write count is 500. This may change as flash technology evolves.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.1.20.5 |
upgradable_devices_nameThis returns the name of the upgradable device. This should match the name in the header of the upgrade image being sent to the flash part. If the name does not match with any of the names returned then the device that we are attempting to upgrade is unavailable for upgrading. Additional information: This object returns the HP name of the printer and the upgradable devices. There is one Name object per upgradable device. This should match what is in the PJL header of the RFU job Web Jet Admin uses this to ensure the printer or device is available to be upgraded.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.1.20.6 |
upgradable_devices_versionThis object will return a string value representing the current revision of firmware that device X is operating with. This is used to determine if code needs to be upgraded when a firmware bundle comes in, in an upgrade job. Additional information: Web Jet Admin uses the version string that is returned to determine what peices of an RFU bundle need to be upgraded when an RFU job is being built. This internal object will return the current version string of the printer or device that it corresponds to.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.1.20.7 |
remote_upgrade_enableEnables or disables the ability to upgrade the firmware associated with any device that is available to be upgraded. This will be set to on or off at the RFU level in that if this mode is on any available device can be upgraded and if this mode is off none of the devices can be upgraded. There is not an individual mode for each device. Trying to set this to a value other than eOn or eOff will cause an UnsupportedValue error to occur.rw Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.1.20.8 |
source_subsystem OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.2 |
io OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.2.1 |
settings_io OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.1 |
io_timeoutThe amount of time, in seconds, to wait for more print job data to be received before an I/O timeout occurs. The I/O channel being timed is the I/O channel that received the data associated with the current print job. If an I/O timeout occurs, the PDL processing sub-system assumes all the data associated with the current print job has been received, and processes the end of job in a PDL specific manner. The POS specifies the supported values. Additional information: If an I/O timeout occurs,the PDL processing sub-system will consider it an end of job condition only if there is data from another I/O subsystem waiting to be processed. The supported values are 5 to 300 seconds. Setting to a value outside the supported range returns <noError> status and the value will be snapped to the nearest supported value.rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.1.1 |
io_switchIndicates if the device will switch between I/O channels when a job boundary is encountered and print job data is available on another I/O channel.ro Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.1.2 |
ports OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.3 |
port1 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.3.1 |
port1_parallel_speedReturns or changes the maximum parallel I/O port speed, for port 1. This object is only supported if this port is a parallel port. An eSlow setting causes a 10 us busy pulse per received byte of data. An eFast setting causes a 1.5 us busy pulse per received byte of data. In rare cases, setting this value to eFast can cause the parallel port to no longer transfer data reliably. Additional information: When the value of this object is changed, it takes effect immediately. It is recommended that the printer be offline and not in a job when this object is changed.rw Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.3.1.4 |
port1_parallel_bidirectionalityReturns or changes whether the parallel I/O port supports bidirectional communication for port 1. This object is only supported if this port is a parallel port. Additional information: A get on this object returns the current mode for the parallel port. Setting this object specifies whether or not bidirectional communications will be allowed.rw Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.3.1.5 |
spooler OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.2.4 |
settings_spooler OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.2.4.1 |
mopy_modeControls or reports how mopies are generated. eOff turns off the mopy feature. eAuto allows the device to determine the best method for generating mopies based on the device configuration. eStandard spools the I/O data and replays the I/O data multiple times to generate the mopies. eEnhanced spools the rasterized page images and replays the rasterized data to generate the mopies. Typically, the rasterized data will be larger and will allow all but the first mopy to print at speed. If the job being mopied is not extremely complex, then the first mopy will print at speed also.rw Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.2.4.1.1 |
processing_subsystem OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.3 |
pdl OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.3.3 |
settings_pdl OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1 |
default_copiesReturns or changes default copies. Default copies is the default values used by the PDL to control the number of copies of each page in the print job that are printed. The print job can override this value. The list of supported values should be documented in the device POS. Additional information: The supported values are 1 through 32000. Setting to an unsupported value causes the printer to substitute in a snap value and to return <noError> status. The snaps are as follows: <1 snaps to 1 >999 snaps to 32000rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.4 |
form_feedInstructs the PDL processing sub-system to finishing processing the current page of the current job. Form feed is also known as close page or eject page. If the PDL processing sub-system is in a FORM-FEED-NEEDED state, this causes the device to flush or finish processing the current page of the current job. If the device is not in the FORM-FEED-NEEDED state, an <genErr> will occur.rw Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.5 |
default_vertical_black_resolutionReturns or changes the value of the default vertical black resolution. The units are dots per inch. Additional information: In LaserJet 8100 changing this OID also causes DEFAULT-HORIZONTAL-BLACK RESOLUTION to change. DEFAULT-HORIZONTAL-BLACK-RESOLUTION and DEFAULT-VERTICAL-BLACK-RESOLUTION must always be the same. The supported values are: LaserJet 4100: 300, 600, 1200 Color Products: 600 LaserJet 9000: 300, 600 Setting to an unsupported value causes the printer to substitute in a snap value and to return <noError> status. The snap values are as follow: LaserJet 4100: 450 >= n < 900 snaps to 600 n >= 900 snaps to 1200 Color Products: n snaps to 600 LaserJet 9000: n < 450 snaps to 300 n >=450 snaps to 600rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.8 |
default_horizontal_black_resolutionReturns or changes the value of the default horizontal black resolution. The units are dots per inch. Additional information: In LaserJet 8100 changing this object also causes DEFAULT-VERTICAL-BLACK RESOLUTION to change. DEFAULT-HORIZONTAL-BLACK-RESOLUTION and DEFAULT-VERTICAL-BLACK-RESOLUTION must always be the same. The supported values are: LaserJet 4100: 300, 600, 1200 Color Products: 600 LaserJet 9000: 300, 600 Setting to an unsupported value causes the printer to substitute in a snap value and to return <noError> status. The snap values are as follow: LaserJet 4100: n < 450 snaps to 300 450 >= n < 900 snaps to 600 n >= 900 snaps to 1200 Color Products: n snaps to 600 LaserJet 9000: n < 450 snaps to 300 n >=450 snaps to 600rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.9 |
default_page_protectReturns or changes the default page protection behavior. If eOff, the device does not reserve memory for holding the entire raster form of a processed page. If eOn, then memory is reserved. If eAuto, the device determines the amount of memory to reserve. Additional information: Setting to eOn causes MET to be more conservative, but it will not allocate memory to hold an entire rasterized page.rw Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.10 |
default_lines_per_pageReturns or changes the default number of lines per page. The POS indicates the supported values. An unsupported value causes the printer to use the closest supported value, causing the printer to return the <noError>. Additional information: The supported values in LaserJet 8150 are 5 to 128. Setting to an unsupported value causes the the printer to substitute in a snap value and to return <noError> status. The snap values are as follow: <5 snaps to 5 >128 snaps to 128rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.11 |
default_vmiReturns or changes the default vertical motion index. The unit of measure for VMI is centipoints per line. The POS indicates the supported values. An unsupported value causes the printer to use the closest supported value, causing the printer to return <noError>.rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.12 |
default_media_sizeThis indicates the default media size. A write of an unsupported value causes an <ErrorInvalidOrUnsupported Value>. Complete list of supported media sizes along with their dimensions are listed in the ''Media Size Table'' near the end of this document. (for a full list of media size enums see the end of this file)rw Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.13 |
cold_reset_media_sizeReturns or sets the media size that is used as the DEFAULT-MEDIA-SIZE when a cold reset occurs.rw Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.19 |
default_media_nameReturns or sets the media name that is used until the media name is changed by a print job command. Additional information: This string must be one of the MEDIAn-NAME objects. The value of this object is saved across a power cycle.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.22 |
reprintReturns or changes the reprint (jam recovery) setting. If eOn, then the device will reprint pages jammed pages. If eOff, the device will not attempt to reprint jammed pages. If eAuto, a device dependent algorithm (which should be documented in the POS) will be used to determine if the page gets reprinted. This object controls all PDLs, unless a specific PDL supports its own reprint control mechanism. To date, only PostScript has a PDL reprint control mechanism.rw Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.36 |
default_bits_per_pixelControls the number of levels used (per pixel) when printing grayscale or color images.rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.39 |
status_pdl OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.2 |
form_feed_neededIndicates if the PDL processing sub-system has made marks on the current page and the source subsystem has been idle for a device specific amount of time. Additional information: LaserJet 8150 will set this object to eTrue when it has made marks on the current page, the IO-TIMEOUT has expired while PCL was running in `backward-compatibility mode' (which is caused by jobs consisting purely of PCL data with no prepended PJL commands), and no data is pending on another I/O. Once it is set to eTrue, more data on the same I/O will cause this object to be set to eFalse, until the above conditions are met again.ro Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.2.2 |
pdl_pcl OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.3 |
pcl_total_page_countTotal number of PCL pages printed by the device. Additional information: In LaserJet 8150 the PCL page count is kept in NVRAM, and the NVRAM value is updated at least every 10 pages. NOTE: The value returned by this object will be incremented every page but if power is lost between NVRAM updates, up to 9 pages of the page count may be lost. The page count counter will be reset to zero after 16,777,215 (2^24-1) pages. The page count is incremented when a sheet of media is pulled from an input tray. A duplex printed sheet will cause this counter to be incremented by two.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.3.5 |
pcl_default_font_heightReturns or changes the default PCL height. Height is an approximate measure of the body of the type in centipoints. A centipoint is 1/7200 inch. Height applies only to proportional fonts. Point size, in points, can be converted to font height, in centipoints, by multiplying the point size by 100. The POS indicates the supported values. An unsupported value causes the printer to use the closest supported value, causing the printer to return <noError>. ''Closest'' means the smallest absolute difference. Additional information: Supported values range from 400 to 99975, in increments of 25 units. Setting to an unsupported value causes the printer to substitute in a snap value and to return <noError> status. The snap values are as follow: <=400 snaps to 400 >=99975 snaps to 99975 Unsupported values in the range 400 to 99975 snap DOWN to the previous supported value (i.e 25293 snaps to 25275 or 75038 snaps to 75025).rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.3.13 |
pcl_default_font_sourceReturns or changes the value of the default font source variable in NVRAM.rw Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.3.14 |
pcl_default_font_numberReturns or changes the value of the default font number variable in NVRAM. Writing an unsupported value causes the printer to generate an <badValue>. Additional information: Valid numbers or 0 - 255, but only font numbers that are included in the PCL FONT LIST are selectable.rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.3.15 |
pcl_default_font_widthReturns or changes the default PCL font width. Width is expressed as the width of a character in centipoints. A centipoint is 1/7200 inch. Width applies only to fixed space fonts. Pitch, in character per inch, can be converted to font width, in centipoints, by dividing 7200 by the pitch. The POS indicates the supported values. An unsupported value causes the printer to use the closest supported value, causing the printer to return <noError>. ''Closest'' means the smallest absolute difference. Additional information: Setting to an unsupported value causes the printer to substitue in a snap value (listed below) and return <noError> status. The snap values for pitch are as follow: <=44 snaps to 44 >=9999 snaps to 9999rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.3.16 |
pdl_postscript OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.4 |
postscript_total_page_countTotal number of PostScript pages printed by the device. Additional information: This object is only supported if the PostScript option is installed. In LaserJet 8150 the count is kept in NVRAM, and the NVRAM value is updated at least every 10 sheets. NOTE: The value returned by this object will be incremented every sheet but if power is lost between NVRAM updates up to 9 sheets of the count may be lost. The counter will be reset to zero after 16,777,215 (2^24-1) pages.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.4.5 |
postscript_print_errorsReturns or changes the value of the print PostScript errors setting. If eOn, PostScript prints an error page showing the error encountered and the stack at the time of the error. Additional information: This object is only supported if the PostScript option is installed.rw Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.4.11 |
pjl OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.3.5 |
webserver_proc_sub OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.3.9 |
settings_webserver OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.3.9.1 |
web_server_securityEach collection bit represents a device or Embedded Web Server feature that can be enabled or disabled via this object.rw OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.3.9.1.3 |
destination_subsystem OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4 |
print_engine OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1 |
settings_prt_eng OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1 |
override_media_nameSets a string identifying the media name that is to be used in place of the currently requested media. The substitution will continue until another media is selected. If set to a named media that is not currently available the requested media is not overridden. Additional information: When a request is received to print on a size and type of media that is not currently available, this object contains the desired media name as set by the print job. This object should be set to a media name that is currently available in the printer. If a paper mount request is not pending, attempting to get or set this object will cause <noSuchName> to be returned. Setting this object to a string other than one of the MEDIAn-NAME objects (MEDIA-NAMES-AVAILABLE is applied) will cause a status of <badValue> to be returned.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.2 |
override_media_sizeSets the media size that is to be used in place of the currently requested media size. Additional information: When a request is received to print on a size and type of media that is not currently available, this object contains the desired size as set by the print job. This object should be set to a media size that is currently available to the printer. If a paper mount request is not pending, attempting to get or set this object will cause <noSuchName> to be returned.rw Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.3 |
marking_agent_density OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.9 |
marking_agent_density_settingReturns or sets the marking agent density setting for each of the marking agents installed. The Marking Agent (aka Print) density is the instantaneous amount of marking agent applied to the media while printing. A value of zero has the lowest print density, yielding a lighter page. A value of 10 has the highest print density, yielding a darker page. The device POS will document what values are supported. Additional information: See the description for PRINT-DENSITY .rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.9.1 |
status_prt_eng OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2 |
total_color_page_countTotal number of color pages printed by the device. Additional information: Any page with one or more color pixels is counted as a color page. Pages that only contain black marks are not counted by this object. The valid range of this object is 0 to 2^24-1. When the number of color pages printed exceeds the maximum color page count, the value will roll to zero. (Realistically, this should never happen since that value is mo re than 16 times the rated life of the engine.) A duplexed sheet of media will cause the counter to be incremented by two.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.7 |
duplex_page_countTotal number of sheets of media that have been duplex printed. A sheet is counted if it travels through the duplex page path, regardless of whether or not marks are made on the page. The POS will indicate if the value is kept in NVRAM. Additional information: In LaserJet 8150 the count is kept in NVRAM however the NVRAM value is only updated every 10 sheets. NOTE: The value returned by this object will be incremented every sheet but if power is lost between NVRAM updates up to 9 sheets of the count may be lost. The counter will be reset to zero after 16,777,215 (2^24-1) pages.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.22 |
print_engine_revisionPrint engine revision string. Additional information: The symbol set for this string is Roman-8. Converts engine revision number to a string and returns it.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.26 |
printer_calibration_dhalf OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.37 |
printer_cal_dhalf_page_countProvides the page count when the last DHALF calibration occurred. A '-1' indicates that a calibration of this kind has not taken place yet. This object exists (and is meaningful) only in color printers. Additional information: Provides the page count when last DHALF calibration occurred. A -1 indicates that a calibration of this kind has not taken place yet. This object exists (and is meaningful) only in color printers.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.37.1 |
printer_cal_dhalf_utcProvides the time (in UTC - Universal Time Code format) when the last DHALF calibration occurred. This value could be zero if no calibration has taken place or if the printer lacked real-time. This object exists (and is meaningful) only in color printers. Additional information: Provides the time (in UTC - Universal Time Code format) when last DHALF calibration occurred. This value could be zero if no calibration has taken place and / or if the printer lacked real-time. This object exists (and is meaningful) only in color printers.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.37.2 |
printer_calibration_cpr OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.38 |
printer_cal_cpr_page_countProvides the page count when last CPR calibration occurred. A '-1' indicates that a calibration of this kind has not taken place yet. This object exists (and is meaningful) only in color printers. Additional information: Provides the page count when last CPR calibration occurred. A -1 indicates that a calibration of this kind has not taken place yet. This object exists (and is meaningful) only in color printers.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.38.1 |
printer_cal_cpr_utcProvides the time (in UTC - Universal Time Code format) when the last CPR calibration occurred. This value could be zero if no calibration has taken place or if the printer lacked real-time. This object exists (and is meaningful) only in color printers. Additional information: Provides the time (in UTC - Universal Time Code format) when last CPR calibration occurred. This value could be zero if no calibration has taken place and / or if the printer lacked real-time. This object exists (and is meaningful) only in color printers.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.38.2 |
intray OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3 |
settings_intray OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.1 |
input_tray_auto_selectIndicates if the device will automatically try to load media from the next input media tray in the auto-select sequence (defined by each device) when it cannot load media from the current tray. Locked trays will not be permitted in the auto-select sequence. This object has no meaning if there is only one unlocked input media tray. Additional information: Indicates whether, when the requested input tray does not contain suitable media, the printer will try to auto-select another input tray that has usable media loaded. If this object is set to eOff(1), then the printer will not try to auto-select another tray and will simply prompt the user to load the requested tray with the requested media. If the object is set to eOn(2), then auto-selection will be used to try to find another suitable input tray.rw Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.1.2 |
default_custom_paper_dim_unitThe units of measure used to specify the width and height of the printer's default custom paper size. The unit of measure of eTenThousandthsOfInches is 0.0001 inches. Additional information: The units of measure used to specify the width and height of the printer's default custom paper size. The unit of measure of eTenThousandthsOfInches is 0.0001 inches.rw Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.1.10 |
default_custom_paper_feed_dimSets the printer's default custom paper size dimension in the feed direction (direction parallel to the direction of paper feeding). The value for this object is specified in micrometers or tenthousandths of an inch, depending upon the value of DEFAULT-CUSTOM-PAPER-DIM-UNIT. The valid range is engine-dependent and should be documented in the POS for each product. Additional information: Sets the printer's default custom paper size dimension in the feed direction (direction parallel to the direction of paper feeding). The value for this object is specified in micrometers or tenthousandths of an inch, depending upon the value of DEFAULT-CUSTOM-PAPER-DIM-UNIT. The valid range is engine-dependent and should be documented in the POS for each product.rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.1.11 |
default_custom_paper_xfeed_dimSets the printer's default custom paper size dimension in the cross-feed direction (direction ninety degrees relative to the direction of paper feeding). The value for this object is specified in micrometers or tenthousandths of an inch, depending upon the value of DEFAULT-CUSTOM-PAPER-DIM-UNIT. The valid range is engine-dependent and should be documented in the POS for each product. Additional information: Sets the printer's default custom paper size dimension in the cross-feed direction (direction ninety degrees relative to the direction of paper feeding). The value for this object is specified in micrometers or tenthousandths of an inch, depending upon the value of DEFAULT-CUSTOM-PAPER-DIM-UNIT. The valid range is engine-dependent and should be documented in the POS for each product.rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.1.12 |
input_tray_max_media_feed_dimThe maximum physical media size in the feed direction of this input device expressed in units of measure specified by INPUT- TRAY-MIN-MAX-DIM-UNIT. A value of (-1) implies 'unlimited', a value of (-2) implies 'unknown'. Additional information: The maximum physical media size in the feed direction of this input device expressed in units of measure specified by PrtInputDimUnit. A value of (-1) implies 'unlimited', a value of (-2) implies 'unknown'. Refer to Printer Management Standards web page, http://bldlabs.boi.hp.com/BLDPrinterLab/Project/PrinterManagement, for more details in the original format of the Standard Printer MIB.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.1.14 |
input_tray_max_media_xfeed_dimThe maximum physical media size across the feed direction of a particular input device expressed in units of measure specified by INPUT-TRAY-MIN-MAX-DIM-UNIT. A value of (-1) implies 'unlimited', a value of (-2) implies 'unknown'. Additional information: The maximum physical media size across the feed direction of this input device expressed in units of measure specified by PrtInputDimUnit. A value of (-1) implies 'unlimited', a value of (-2) implies 'unknown'. Refer to Printer Management Standards web page, http://bldlabs.boi.hp.com/BLDPrinterLab/Project/PrinterManagement, f or more details in the original format of the Standard Printer MIB.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.1.15 |
input_tray_min_media_feed_dimThe minimum physical media size in the feed direction of a particular input device expressed in units of measure specified by PrtInputMinMaxDimUnit. A value of (-1) implies 'unlimited', a value of (-2) implies 'unknown'. Additional information: The minimum physical media size in the feed direction of this input device expressed in units of measure specified by PrtInputDimUnit. A value of (-1) implies 'unlimited', a value of (-2) implies 'unknown'. Refer to Printer Management Standards web page, http://bldlabs.boi.hp.com/BLDPrinterLab/Project/PrinterManagement, for more details in the original format of the Standard Printer MIB.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.1.16 |
input_tray_min_media_xfeed_dimThe minimum physical media size across the feed direction of a particular input device expressed in units of measure specified by PrtInputMinMaxDimUnit. A value of (-1) implies 'unlimited', a value of (-2) implies 'unknown'. Additional information: The minimum physical media size across the feed direction of this input device expressed in units of measure specified by PrtInputDimUnit. A value of (-1) implies 'unlimited', a value of (-2) implies 'unknown'. Refer to Printer Management Standards web page, http://bldlabs.boi.hp.com/BLDPrinterLab/Project/PrinterManagement, for more details in the original format of the Standard Printer MIB.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.1.17 |
intrays OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3 |
intray1 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.1 |
tray1_media_size_loadedReturns the media size that is currently configuredconfigured in tray #1. This object can be set to indicate the media size currently loaded, if the printer supports input trays that can not sense the media size. Complete list of supported media sizes along with their dimensions are listed in the ''Media Size Table'' near the end of this document.rw Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.1.1 |
tray1_phdProvides the number of the Paper Handling Device that contains this input tray. Additional information: The internal trays belong to device 0, which is the base engine. The envelope feeder (if supported) is considered to be device 1 and the external input devices can number between 2 and 6 depending on individual user configurations.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.1.12 |
intray2 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.2 |
tray2_media_size_loadedReturns the media size that is currently configured in tray #2. Complete list of supported media sizes along with their dimensions are listed in the ''Media Size Table'' near the end of this document. Additional information: If the tray drawer is open, a get on this object will cause a status of <genErr> to be returned. If the tray is empty, the size that the tray is configured for will be returned. If Tray 2 is a 500-sheet standard tray, eJISB5 and eUSExecutive are not valid values.rw Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.2.1 |
tray2_phdProvides the number of the Paper Handling Device that contains this input tray.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.2.12 |
intray3 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.3 |
tray3_media_size_loadedReturns the media size that is currently configured in tray #3. Complete list of supported media sizes along with their dimensions are listed in the ''Media Size Table'' near the end of this document. Additional information: If the tray drawer is open, a get on this object will cause a status of <genErr> to be returned. If the tray is empty, the size that the tray is configured for will be returned.rw Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.3.1 |
tray3_phdProvides the number of the Paper Handling Device that contains this input tray.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.3.12 |
outbin OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4 |
settings_outbin OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4.1 |
overflow_binReturns or sets the bin that will be used for additional sheets of media when the current bin is full and printing is allowed to continue. Additional information: The data for this object is stored in NVRAM.rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4.1.4 |
outbins OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4.3 |
outbin1 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4.3.1 |
outbin1_override_modeReturns or sets the device behavior when this output bin condition causes printing to stop. cCancelJob - The device cancels the job. cOutbinFullOverride - The device sends subsequent media to the overflow bin. cOutbinAttentionOverride - The device ignores the attention condition and continues printing. cBinderAttentionOverride - The device ignores the binder attention condition and continues printing. Additional information: If cCancelJob is set, the current print job will be cancelled regardless of other item settings. If cOutbinFullOverride is set and this bin is the designated overflow bin (OVERFLOW-BIN = 1), then the bit is ignored. This object describes the action that is performed when the JOB-OUTPUT-AUTO-CONTINUE-TIMEOUT expires. If no bits are set, no override action is taken (the printer will continue to wait). The action performed by the CONTINUE object being set to eInitiateAction or the GO key being pressed on the control panel may cause different actions. See the LaserJet 8150 Control panel ERS and the CONTINUE object description for information on the actions that occur for those conditions.rw OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4.3.1.9 |
marking_agent OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.5 |
settings_marking_agent OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.5.1 |
low_marking_agent_processingReturns or changes how the device processes a low marking agent event. If eCont, then the device continues to print. If eStop, then the device stops until a continue event occurs.rw Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.5.1.3 |
out_marking_agent_processingReturns or changes how the device processes an out marking agent event. If eCont, then the device continues to print. If eStop, then the device stops until a continue event occurs.ro Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.5.1.10 |
marker_density_calibrationReturns the calibration status or triggers a calibration cycle. All calibration procedures are used if set to eCalibrateALL. If set to eCalibrateDMAX then a full density engine calibration is triggered. If set to eCalibrateDHALF, then a Halftone calibration is triggered. Additional information: Returns the calibration status or triggers a calibration cycle. All calibration procedures are used if set to eCalibrateALL. If set to eCalibrateColor then a full density engine calibration is triggered. If set to eCalibrateHalftone, then a Halftone calibration is triggered. If set to eCalibrateColorPlaneRegistration, then a Color Plane Registration calibration is triggered. If set to eCalibrateDrumPhaseAdjustment, then a Drum Phase Adjustment calibration is triggered.rw Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.5.1.11 |
ph OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7 |
ph_devices OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3 |
ph2 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3.2 |
phd2_device_specific_commandThis object is used to send device-specific data to the paper handling device. The meaning of the device-specific command is dependent on the paper handling device and must be specified in the POS. If the paper handling device does not accept the command, then an <badValue> will be returned. If the device accepts the command, it may still be processing the command after the response has been returned. Depending on the device, the application may need to query PHDx-DEVICE-MEMORY to see when the command has completed. Additional information: This object is used to send device-specific data to the paper handling device. The meaning of the device- specific command is dependent on the paper handling device and must be specified in the POS. If the paper handling device does not accept the command, then an <badValue> will be returned. If the device accepts the command, it may still be processing the command after the response has been returned. Depending on the device, the application may need to query PHDx-DEVICE-MEMORY to see when the command has completed.rw OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3.2.2 |
ph3 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3.3 |
phd3_device_specific_commandThis object is used to send device-specific data to the paper handling device. The meaning of the device-specific command is dependent on the paper handling device and must be specified in the POS. If the paper handling device does not accept the command, then an <badValue> will be returned. If the device accepts the command, it may still be processing the command after the response has been returned. Depending on the device, the application may need to query PHDx-DEVICE-MEMORY to see when the command has completed. Additional information: This object is used to send device-specific data to the paper handling device. The meaning of the device- specific command is dependent on the paper handling device and must be specified in the POS. If the paper handling device does not accept the command, then an <badValue> will be returned. If the device accepts the command, it may still be processing the command after the response has been returned. Depending on the device, the application may need to query PHDx-DEVICE-MEMORY to see when the command has completed.rw OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3.3.2 |
ph4 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3.4 |
phd4_device_specific_commandThis object is used to send device-specific data to the paper handling device. The meaning of the device-specific command is dependent on the paper handling device and must be specified in the POS. If the paper handling device does not accept the command, then an <badValue> will be returned. If the device accepts the command, it may still be processing the command after the response has been returned. Depending on the device, the application may need to query PHDx-DEVICE-MEMORY to see when the command has completed. Additional information: This object is used to send device-specific data to the paper handling device. The meaning of the device- specific command is dependent on the paper handling device and must be specified in the POS. If the paper handling device does not accept the command, then an <badValue> will be returned. If the device accepts the command, it may still be processing the command after the response has been returned. Depending on the device, the application may need to query PHDx-DEVICE-MEMORY to see when the command has completed.rw OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3.4.2 |
ph5 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3.5 |
phd5_device_specific_commandThis object is used to send device-specific data to the paper handling device. The meaning of the device-specific command is dependent on the paper handling device and must be specified in the POS. If the paper handling device does not accept the command, then an <badValue> will be returned. If the device accepts the command, it may still be processing the command after the response has been returned. Depending on the device, the application may need to query PHDx-DEVICE-MEMORY to see when the command has completed. Additional information: This object is used to send device-specific data to the paper handling device. The meaning of the device- specific command is dependent on the paper handling device and must be specified in the POS. If the paper handling device does not accept the command, then an <badValue> will be returned. If the device accepts the command, it may still be processing the command after the response has been returned. Depending on the device, the application may need to query PHDx-DEVICE-MEMORY to see when the command has completed.rw OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3.5.2 |
ph6 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3.6 |
phd6_device_specific_commandThis object is used to send device-specific data to the paper handling device. The meaning of the device-specific command is dependent on the paper handling device and must be specified in the POS. If the paper handling device does not accept the command, then an <badValue> will be returned. If the device accepts the command, it may still be processing the command after the response has been returned. Depending on the device, the application may need to query PHDx-DEVICE-MEMORY to see when the command has completed. Additional information: This object is used to send device-specific data to the paper handling device. The meaning of the device- specific command is dependent on the paper handling device and must be specified in the POS. If the paper handling device does not accept the command, then an <badValue> will be returned. If the device accepts the command, it may still be processing the command after the response has been returned. Depending on the device, the application may need to query PHDx-DEVICE-MEMORY to see when the command has completed.rw OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3.6.2 |
print_media OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8 |
settings_print_media OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.1 |
media_names_availableThe value of this object controls which of the MEDIAx-NAME objects are supported. If a bit is set to zero, then attempting to get or set the corresponding MEDIAx-NAME objects will return <noSuchName>. Additional information: Setting a bit to one will cause the corresponding MEDIAn- objects to be available (attempting to access an unavailable object will return <noSuchName>). MEDIA1- objects are always present, as this is the default media. If this object is set to a value that does not include cMediaName2Available, that bit will be set and a status of <noError> will be returned.rw OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.1.1 |
north_edge_offsetReturns or sets the number of 300 dpi dots by which the image is shifted. Shift is relative to the leading edge of the medium as the medium flows through the marking engine with the side to be imaged facing the observer. The leading edge is the North edge and the other edges are defined by the normal compass layout of directions with the compass facing the observer. The adjustment is for all pages printed. A positive value moves the image away from the leading edge of the medium. A negative value moves the image closer to the leading edge of the medium. The value 0 will return the image to its factory default position. Additional information: Returns or sets the number of 300 dpi dots by which the image is shifted. Shift is relative to the leading edge of the medium as the medium flows through the marking engine with the side to be imaged facing the observer. The leading edge is the North edge and the other edges are defined by the normal compass layout of directions with the compass facing the ob server. The adjustment is for all pages printed. A positive value moves the image away from the leading edge of the medium. A negative value moves the image closer to the leading edge of the medium. The value 0 will return the image to its factory default position. The value of this object is stored in NVRAM.rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.1.2 |
media_info OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3 |
media1 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.1 |
media1_nameMedia 1 name. Additional information: The symbol set for this string is Roman-8.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.1.1 |
media1_short_nameLength restricted version of the media name 1. The length restriction is required to allow the media name to be displayed on the device's control panel. The device POS must state the maximum number of characters allowed. If the device also has a limitation on what characters in a character set can be used (e.g. only uppercase characters allowed), the POS should also state character restrictions. Additional information: The maximum supported string length is 9 characters. If the user entered string is too long, the device will store the first 9 characters and will return the <noError> status. The characters must be in the range 20H to 7FH except 5C cannot be used. The default symbol set is Roman-8 for English; additional legal symbol sets are ISOLatin5, ISOLatin2 and Windows31J. Setting this object with characters outside of the range or of an illegal symbol set will cause an error status of <badValue> to be returned.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.1.2 |
media1_page_countNumber of sheets of media 1 that have been printed. The device POS should state whether this value is lost across a power cycle or kept in NVRAM. Additional information: For LaserJet 8150 this page count is saved in NVRAM after every 10 pages. The maximum value is 4,294,967,295 which will never be reached in normal operation. The page count is incremented when a sheet of media is pulled from an input tray. A duplex printed sheet will cause this counter to be incremented by one. The data for this object is stored in NVRAM.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.1.3 |
media1_engine_media_modeThe engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: The engine processing characteristics that are to be applied to this media type. Currently, 'engine processing characteristics' denotes changes to fusing temperature and/or transfer roller voltage. The data for this object is stored in NVRAM.rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.1.4 |
media2 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.2 |
media2_nameMedia 2 name. Additional information: See MEDIA1-NAME.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.2.1 |
media2_short_nameLength restricted version of the media name 2. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.2.2 |
media2_page_countNumber of sheets of media 2 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.2.3 |
media2_engine_media_modeThe engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.2.4 |
media3 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.3 |
media3_nameMedia 3 name. Additional information: See MEDIA1-NAME.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.3.1 |
media3_short_nameLength restricted version of the media name 3. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.3.2 |
media3_page_countNumber of sheets of media 3 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.3.3 |
media3_engine_media_modeThe engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.3.4 |
media4 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.4 |
media4_nameMedia 4 name. Additional information: See MEDIA1-NAME.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.4.1 |
media4_short_nameLength restricted version of the media name 4. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.4.2 |
media4_page_countNumber of sheets of media 4 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.4.3 |
media4_engine_media_modeThe engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.4.4 |
media5 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.5 |
media5_nameMedia 5 name. Additional information: See MEDIA1-NAME.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.5.1 |
media5_short_nameLength restricted version of the media name 5. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.5.2 |
media5_page_countNumber of sheets of media 5 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.5.3 |
media5_engine_media_modeThe engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.5.4 |
media6 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.6 |
media6_nameMedia 6 name. Additional information: See MEDIA1-NAME.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.6.1 |
media6_short_nameLength restricted version of the media name 6. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.6.2 |
media6_page_countNumber of sheets of media 6 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.6.3 |
media6_engine_media_modeThe engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.6.4 |
media7 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.7 |
media7_nameMedia 7 name. Additional information: See MEDIA1-NAME.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.7.1 |
media7_short_nameLength restricted version of the media name 7. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.7.2 |
media7_page_countNumber of sheets of media 7 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.7.3 |
media7_engine_media_modeThe engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.7.4 |
media8 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.8 |
media8_nameMedia 8 name. Additional information: See MEDIA1-NAME.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.8.1 |
media8_short_nameLength restricted version of the media name 8. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.8.2 |
media8_page_countNumber of sheets of media 8 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.8.3 |
media8_engine_media_modeThe engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.8.4 |
media9 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.9 |
media9_nameMedia 9 name. Additional information: See MEDIA1-NAME.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.9.1 |
media9_short_nameLength restricted version of the media name 9. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.9.2 |
media9_page_countNumber of sheets of media 9 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.9.3 |
media9_engine_media_modeThe engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.9.4 |
media10 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.10 |
media10_nameMedia 10 name. Additional information: See MEDIA1-NAME.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.10.1 |
media10_short_nameLength restricted version of the media name 10. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.10.2 |
media10_page_countNumber of sheets of media 10 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.10.3 |
media10_engine_media_modeThe engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.10.4 |
media11 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.11 |
media11_nameMedia 11 name. Additional information: See MEDIA1-NAME.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.11.1 |
media11_short_nameLength restricted version of the media name 11. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.11.2 |
media11_page_countNumber of sheets of media 11 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.11.3 |
media11_engine_media_modeThe engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.11.4 |
media12 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.12 |
media12_nameMedia 12 name. Additional information: See MEDIA1-NAME.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.12.1 |
media12_short_nameLength restricted version of the media name 12. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.12.2 |
media12_page_countNumber of sheets of media 12 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.12.3 |
media12_engine_media_modeThe engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.12.4 |
media13 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.13 |
media13_nameMedia 13 name. Additional information: See MEDIA1-NAME.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.13.1 |
media13_short_nameLength restricted version of the media name 13. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.13.2 |
media13_page_countNumber of sheets of media 13 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.13.3 |
media13_engine_media_modeThe engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.13.4 |
media14 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.14 |
media14_nameMedia 14 name. Additional information: See MEDIA1-NAME.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.14.1 |
media14_short_nameLength restricted version of the media name 14. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.14.2 |
media14_page_countNumber of sheets of media 14 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.14.3 |
media14_engine_media_modeThe engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.14.4 |
media15 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.15 |
media15_nameMedia 15 name. Additional information: The maximum supported string length is 24 bytes. If the user entered string is too long, the device will store the first 24 bytes and return the <noError> status. See CAUTION statement under Product Specific Use.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.15.1 |
media15_short_nameLength restricted version of the media name 15. See MEDIA1-SHORT-NAME for details. Additional information: The maximum supported string length is 9 characters. If the user entered string is too long, the device will store the first 9 characters and will return the <noError> status. The characters must be in the range 20H to 7FH except 5C cannot be used. The default symbol set is Roman-8 for English; additional legal symbol sets are ISOLatin5, ISOLatin2 and Windows31J. Setting this object with characters outside of the range or of an illegal symbol set will cause an error status of <badValue> to be returned.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.15.2 |
media15_page_countNumber of sheets of media 15 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.15.3 |
media15_engine_media_modeThe engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.15.4 |
media16 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.16 |
media16_nameMedia 16 name. Additional information: See MEDIA15-NAME.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.16.1 |
media16_short_nameLength restricted version of the media name 16. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA15-SHORT-NAME.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.16.2 |
media16_page_countNumber of sheets of media 16 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA15-PAGE-COUNT.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.16.3 |
media16_engine_media_modeThe engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.16.4 |
media17 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.17 |
media17_nameMedia 17 name. Additional information: See MEDIA15-NAME.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.17.1 |
media17_short_nameLength restricted version of the media name 17. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA15-SHORT-NAME.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.17.2 |
media17_page_countNumber of sheets of media 17 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA15-PAGE-COUNT.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.17.3 |
media17_engine_media_modeThe engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.17.4 |
media18 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.18 |
media18_nameMedia 18 name. Additional information: See MEDIA15-NAME.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.18.1 |
media18_short_nameLength restricted version of the media name 18. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA15-SHORT-NAME.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.18.2 |
media18_page_countNumber of sheets of media 18 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA15-PAGE-COUNT.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.18.3 |
media18_engine_media_modeThe engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.18.4 |
media19 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.19 |
media19_nameMedia 19 name. Additional information: See MEDIA15-NAME.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.19.1 |
media19_short_nameLength restricted version of the media name 19. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA15-SHORT-NAME.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.19.2 |
media19_page_countNumber of sheets of media 19 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA15-PAGE-COUNT.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.19.3 |
media19_engine_media_modeThe engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.19.4 |
media20 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.20 |
media20_nameMedia 20 name. Additional information: See MEDIA1-NAME.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.20.1 |
media20_short_nameLength restricted version of the media name 20. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.20.2 |
media20_page_countNumber of sheets of media 20 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.20.3 |
media20_engine_media_modeThe engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.20.4 |
media21 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.21 |
media21_nameMedia 21 name. Additional information: See MEDIA1-NAME.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.21.1 |
media21_short_nameLength restricted version of the media name 21. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.21.2 |
media21_page_countNumber of sheets of media 21 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.21.3 |
media21_engine_media_modeThe engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.21.4 |
media22 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.22 |
media22_nameMedia 22 name. Additional information: See MEDIA1-NAME.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.22.1 |
media22_short_nameLength restricted version of the media name 22. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.22.2 |
media22_page_countNumber of sheets of media 22 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.22.3 |
media22_engine_media_modeThe engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.22.4 |
media_modes OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.4 |
engine_media_modes_supported1The list of engine media modes supported by the device. The modes are each separated by a comma character. An example string would be: 'Normal,Rough,Low,Vellum'.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.4.1 |
media_size OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.5 |
media_size_countThe number of impressions printed on sheets of this media size. The device POS should state whether this value is lost across a power cycle or is kept in permanent storage. Additional information: The value of this object is persistent across a power cycle. The index for these objects, the last number of the OID, uniquely identifies the paper size. This value corresponds to the page sizes listed below. These values are also documented in the PCL Implementor's Guide and the PML Master MIB. 1 US-Executive 2 US-Letter 3 US-Legal 17 ROC 16K 18 JIS Executive 25 ISO and JIS A5 26 ISO and JIS A4 45 JIS B5 65 ISO B5 72 eJapanesePostcardDouble 80 Monarch 81 Commercal-10 90 International DL 91 International C5 100 International B5 101 Custom 32767 Unknown Paper Sizero INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.5.1 |
media_size_west_edge_first_side_offsetReturns or sets the number of 300 dpi dots by which the image is shifted relative to the west edge of the medium (see NORTH-EDGE-OFFSET). The adjustment is for the first printed side of the medium only. A positive value moves the image away from the west edge of the medium. A negative value moves the image closer to the west edge of the medium. The value 0 will return the image to its factory default position. Additional information: Returns or sets the number of 300 dpi dots by which the image is shifted relative to the west edge of the medium (see NORTH-EDGE-OFFSET). The adjustment is for the first printed side of the medium only. A positive value moves the image away from the west edge of the medium. A negative value moves the image closer to the west edge of the medium. The value 0 will return the image to its factory default position. The values in the sub array index are from the media size table in the hpmib. This adjustment is done on a paper size by paper size basis. The standard PCL5 codes for paper size are used for the value used in the OID. Please see S_ARRAY_SUB1 for legal values. The data for this object is stored in NVRAM. The supported values are -126 through 127. Setting to an unsupported value causes the printer to substitute in a snap value and to return <noError> status. The snaps are as follows: <-126 snaps to -126 >127 snaps to 127rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.5.2 |
media_size_west_edge_second_side_offsetReturns or sets the number of 300 dpi dots by which the image is shifted relative to the west edge of the medium (see NORTH-EDGE-OFFSET). The adjustment is for the second printed side of the medium only. A positive value moves the image away from the west edge of the medium. A negative value moves the image closer to the west edge of the medium. The value 0 will return the image to its factory default position. Additional information: Returns or sets the number of 300 dpi dots by which the image is shifted relative to the west edge of the medium (see NORTH-EDGE-OFFSET). The adjustment is for the second printed side of the medium only. A positive value moves the image away from the west edge of the medium. A negative value moves the image closer to the west edge of the medium. The value 0 will return the image to its factory default position. The values in the sub array index are from the media size table in the hpmib. This adjustment is done on a paper size by paper size basis. The standard PCL5 codes for paper size are used for the value used in the OID. Please see S_ARRAY_SUB1 for legal values. The data for this object is stored in NVRAM. The supported values are -126 through 127. Setting to an unsupported value causes the printer to substitute in a snap value and to return <noError> status. The snaps are as follows: <-126 snaps to -126 >127 snaps to 127rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.5.3 |
media_size_west_edge_side_offset_by_trayReturns or sets the number of 300 dpi dots by which the image is shifted relative to the west edge of the medium (see NORTH-EDGE-OFFSET). A positive value moves the image away from the west edge of the medium. A negative value moves the image closer to the west edge of the medium. The value 0 will return the image to its factory default position. Each OID binding corresponds to a valid tray number for this product. There can be a maximum of 15 trays, a combination of internal and external trays. Products that support other combinations of trays will specify this information in the device pos. The data for this object is stored in NVRAM. Additional information: Returns or sets the number of 300 dpi dots by which the image is shifted relative to the west edge of the medium (see NORTH-EDGE-OFFSET). A positive value moves the image away from the west edge of the medium. A negative value moves the image closer to the west edge of the medium. The value 0 will return the image to its factory default position. Each OID binding corresponds to a valid tray number for this product. There can be a maximum of 15 trays, a combination of internal and external trays. Products that support other combinations of trays will specify this information in the device pos. The data for this object is stored in NVRAM. The supported values are -126 through 127. Setting to an unsupported value causes the printer to substitute in a snap value and to return <noError> status. The snaps are as follows: <-126 snaps to -126 >127 snaps to 127rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.5.4 |
media_counts OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.7 |
non_assured_oht_page_countThis is a count of the number of invalid (non-HP Laser Jet) transparencies that have been printed on. This value is incremented every time an invalid OHT is printed on It is reset whenever the fuser count is set to 0. Additional information: This is a count of the number of invalid (non HP Laser Jet) transparencies that have been printed on. This value is incremented every time an invalid OHT is printed on. It is reset whenever the fuser count is set to 0.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.7.1 |
consumables OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10 |
consumables_1 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1 |
consumable_status OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1 |
consumable_status_cartridge_modelThis object is used to read the cartridge model number associated with this consumable. Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1.1 |
consumable_status_manufacturing_dateThis object is used to report the date on which this consumable was manufactured. The format of the string is 'YYYYMMDD', where YYYY is the year, MM is the month (1-12), and DD is the day (1-31). Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1.2 |
consumable_status_serial_numberThis object is used to report the serial number for this consumable. Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1.3 |
consumable_status_capacity_unitsThis object is used to report the usage units used by the CONSUMABLE-STATUS-TOTAL-CAPACITY object. Additional information: This object will only exist on engines that are E-Label capable, but will exist on these engines regardless of the cartridge being Authentic HP or NonHP. This object can be used to ensure the capability of the E-Label feature for a given engine.ro Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1.4 |
consumable_status_total_capacityThis object is used to report the total capacity of a new consumable of this type. The PML object CONSUMABLE-STATUS-CAPACITY-UNITS can be used to determine the units of measure for this PML object. Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1.5 |
consumable_status_reseller_idThis object is used to query and set the reseller ID for this consumable. This ID is represented as an integer that is essentially an enumeration representing a specific reseller that sells this consumable. The device POS should detail the mapping of reseller name to reseller ID. In this way the reseller can program into the consumable a suggested reseller which can in turn be mapped to a web page through which a replacement can be purchased. Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist. The reseller ID is an integer that must be mapped external to the printer by a host application. The value stored must be specific to an external application.rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1.6 |
consumable_status_infoThis object is used to read and write the various status flags supported by this consumable. For LaserJet 4100, LaserJet 4550 the collection bits supported include: cMarkedAsReordered - indicates the consumable has been reordered. This is the only bit that can be both read and written. cTonerLowCondition - indicates a toner low condition has occured. This bit in the collection is read-only to PML. cTonerOutCondition - indicates a toner out condition has occured. This bit in the collection is read-only to PML. cDeveloperLowCondition - indicates a developer low condition has occured. This bit in the collection is read-only to PML. cDeveloperOutCondition - indicates a developer out condition has occured. This bit in the collection is read-only to PML. cDrumLowCondition - indicates a drum low condition has occured. This bit in the collection is read-only to PML. cDrumOutCondition - indicates a drum out condition has occured. This bit in the collection is read-only to PML. cWasteTonerFullCondition - indicates a waste toner full condition has occured. This bit in the collection is read-only to PML. cWasteTonerFullWarningCondition - indicates a waste toner full warning condition has occured. This bit in the collection is read-only to PML. cNewConsumable - indicates the consumable is new and has never been used. This bit in the collection is read-only to PML. cTonerLowNotificationSent - inidicates that toner low notification has been sent for this consumable. This bit in the collection is readonly. cTonerOutNotificationSent - inidicates that toner out notification has been sent for this consumable. This bit in the collection is read only. cAnyPartLowCondition - indicates that at least one part of this consumable has reached a low condition. This bit in the collection is read-only to PML. cAnyPartOutCondition - indicates that at least one part of this consumable has reached an out condition. This bit in the collection is read-only to PML. Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist.rw OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1.7 |
consumable_status_first_install_dateThis object is used to report the date on which this consumable was first installed. The format of the string is 'YYYYMMDD'. Where: YYYY is the year. MM is the month (1-12). DD is the day (1-31). The device POS needs to indicate what will be written in the event the printer does not have a real time clock. Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist. For printers without internal clocks, the date will always be 20000101.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1.8 |
consumable_status_last_use_dateThis object is used to report the date on which this consumable was last used. The format of the string is 'YYYYMMDD'. Where: YYYY is the year. MM is the month (1-12). DD is the day (1-31). The device POS needs to indicate what will be written in the event the printer does not have a real time clock. Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist. For printers without internal clocks, the date will always be 20000101.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1.9 |
consumable_status_page_count_legalThis object is used to report the number of pages that have been printed by this consumable that are of the specified media size - Legal. Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1.11 |
consumable_status_page_count_a4_letterThis object is used to report the number of pages that have been printed by this consumable that are of the specified media size - A4 or Letter. Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1.12 |
consumable_status_page_count_xy_otherThis object is used to report the number of pages that have been printed by this consumable that are of the specified media size - XY or Other. Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1.15 |
consumable_status_job_countThis object is used to report the number of jobs that have been printed by this consumable. Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1.16 |
consumable_status_usage_unitsThis object is used to report the units used to measure the capacity of this consumable. Additional information: This object will only exist on engines that are E-Label capable, but will exist on these engines regardless of the cartridge being Authentic HP or NonHP. This object can be used to ensure the capability of the E-Label feature for a given engine.ro Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1.17 |
consumable_status_usage_countThis object is used to report the number of usage units that remain in this consumable. The units of measurement used by this object can be obtained by querying the CONSUMABLE-STATUS-USAGE-UNITS object. Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1.18 |
consumable_status_manufacturer_nameThis object is used to report the name of the manufacturer of this consumable. The device POS will specify the set of manufacturers that could be returned. Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1.19 |
consumable_status_oem_nameThis object is used to report the name of the OEM of this consumable. This object will typically return the string 'HP'. The device POS will specify if other OEM consumables are supported. Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist. This object should always return 'HP' as the OEM namero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1.20 |
consumable_status_engine_usage_unitsThis object is used to report the units used to measure the capacity of this consumable as reported by the Engine. Additional information: This object will only exist on engines that are E-Label capable, but will exist on these engines regardless of the cartridge being Authentic HP or NonHP. This object can be used to ensure the capability of the E-Label feature for a given engine.ro Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1.21 |
consumable_status_engine_usage_countThis object is used to report the number of usage units, estimated by the engine, that remain in this consumable. The units of measurement used by this object can be obtained by querying the CONSUMABLE-STATUS-ENGINE-USAGE-UNITS object. Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1.22 |
consumable_status_engine_job_countThis object is used to report the number of jobs, as reported by the printer, that have been printed by this consumable. Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1.23 |
consumable_status_total_page_countThis object is used to report the total number of pages that have been printed by this consumable. Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1.24 |
consumable_status_mono_page_countThis object is used to report the number of monochrome pages that have been printed by this consumable. Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1.25 |
consumable_status_color_page_countThis object is used to report the number of color pages that have been printed by this consumable. Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1.26 |
consumable_status_total_equiv_page_countThis object is used to report the total number of equivelent Letter/A4 pages that have been printed by this consumable. Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1.27 |
consumable_status_input_option_sheet_countThis object is used to report the number of pages that have been printed by this consumable that had the input option as their source. Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1.30 |
consumable_status_duplex_sheet_countThis object is used to report the number of pages that have been printed by this consumable that were also duplexed (printed both sides). Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1.31 |
consumable_status_page_count_half_speedThis object is used to report the number of pages that have been printed by this consumable at one half engine speed. Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1.32 |
consumable_status_page_count_quarter_speedThis object is used to report the number of pages that have been printed by this consumable at one quarter engine speed. Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1.33 |
consumable_status_page_count_third_speedThis object is used to report the number of pages that have been printed by this consumable at one third engine speed. Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1.34 |
consumable_status_developer_life_unitsThis object is used to report the units used to measure the developer life remaining. Additional information: This object will only exist on engines that are E-Label capable, but will exist on these engines regardless of the cartridge being Authentic HP or NonHP. This object can be used to ensure the capability of the E-Label feature for a given engine.ro Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1.36 |
consumable_status_developer_lifeThis object is used to report the number of life units, remaining in the developer. The units of measurement used by this object can be obtained by querying the CONSUMABLE-STATUS-DEVELOPER-LIFE-UNITS object. This object will not exist if this consumable does not contain a developer. Additional information: This object will only exist on engines that are E-Label capable, but will exist on these engines regardless of the cartridge being Authentic HP or NonHP. This object can be used to ensure the capability of the E-Label feature for a given engine.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1.37 |
consumable_status_drum_life_unitsThis object is used to report the units used to measure the drum life remaining. Additional information: This object will only exist on engines that are E-Label capable, but will exist on these engines regardless of the cartridge being Authentic HP or NonHP. This object can be used to ensure the capability of the E-Label feature for a given engine.ro Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1.38 |
consumable_status_drum_lifeThis object is used to report the number of life units, remaining in the drum. The units of measurement used by this object can be obtained by querying the CONSUMABLE- STATUS-DRUM-LIFE-UNITS object. This object will not exist if this consumable does not contain a drum. Additional information: This object will only exist on engines that are E-Label capable, but will exist on these engines regardless of the cartridge being Authentic HP or NonHP. This object can be used to ensure the capability of the E-Label feature for a given engine.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1.39 |
consumable_status_authenticationThis object returns the authentication level of the elabel on the given supply. The elabel authentication is returned via the appropriate enum. Additional information: There are three levels of authentication of an ELabel cartridge supported. Each ELabel cartridges level of authentication is provided here, via this enumeration.ro Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.1.40 |
consumable_reorder_urlThis object is used to read and write the URL that can be used to reorder consumables for this device. This URL is set at the factory but can be updated by a reseller or third party. Additional information: The URL can be up to 64 characters long.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.2 |
consumables_status OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.5 |
consumables_life OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.5.1 |
consumable_life_usage_units_remainingThis object reports the current estimate of the number of usage units that remain before this supply is depleted. An installed supply that cannot report such a number will return a value of -2. It is the reponsibility of the host application to query each supply in order to determine an overall device USAGE-UNITS-REMAINING number - the lowest value returned. The unit of measure for this life estimate is determined by reading the corresponding CONSUMABLE-LIFE-USAGE-UNITS object. Additional information: This object will return the Pages or Estimated Pages remaining for the speciffic supply requested by the leaf node of this object.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.5.1.1 |
consumable_life_usage_unitsThis object reports current usage units in use by the corresponding CONSUMABLE-LIFE-USAGE-UNITS-REMAINING object. Additional information: This object returns the units that CONSUMABLE-LIFE-USAGE-UNITS-REMAINING is returned in. Either ePagesRemaining(1) or eEstimatedPagesRemaining(2).ro Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.5.1.2 |
consumable_life_low_thresholdThis object is used to report and modify a threshold value indicating the point in the life of a consumable or supply at which a transition to a LOW state will occur.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.5.1.3 |
consumable_current_stateThis PML object returns the current state of the particular consumable. cAuthLevel1 - Consumable is at Authentication Level 1 cAuthLevel2 - Consumable is at Authentication Level 2 cAuthLevel3 - Consumable is at Authentication Level 3 cGenuineHPUnsupported - Cartridge is GenuineHP intended for another product cDefectiveMemory - Cartridge has a defective memory tag cMissingMemory - Memory tag is missing from the cartridge cLowCondition - Consumable has reached the engine low threshold cOutCondition - Consumable has reached its out threshold cIncorrect - Cartridge inserted is not the correct one cMissing - Consumable is missing from the printer cConfigurableLow - Consumable has reached the configurable low threshold value cStatusArevalid - The status reported on other bits are valid only if the bit is set to 1. If it is 0, the values are invalid. These are the possible states and whenever the consumable is in any of these states, the appropriate bit will be set. The cLowCondition will be set when the consumable reaches the engine low threshold, and cConfigurableLow will be set when the consumable reaches the Configurable Low threshold value. For non-cartridge supplies only cLowCondition, cOutCondition, and cMissing will be supported. Additional information: This object returns the current state of the particular consumable. cAuthLevel1 - Consumable is at Authentication Level 1 cAuthLevel2 - Consumable is at Authentication Level 2 cAuthLevel3 - Consumable is at Authentication Level 3 cGenuineHPUnsupported - Cartridge is GenuineHP intended for another product cDefectiveMemory - Cartridge has a Defective Memory cMissingMemory - Memory is Missing from the Cartridge cLowCondition - Consumable has reached its low threshold cOutCondition - Consumable has reached its out threshold cIncorrect - Cartridge inserted is not the correct one cMissing - Consumable is Missing from the Printer cStatusAreValid - The Status reported on other bits are valid only if this bit is set to 1. If it is 0, the values are invalid. These are the possible states and whenever a Consumable is in any of these states, the appropriate bit will be set. For Non Cartridge Supplies only cLowCondition, cOutCondition and cMissing will be supported.ro OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.7 |
print_meter OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.11 |
printer_average OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.11.1 |
printer_average_marking_agent_coverageThis object is used to read the average marking agent coverage for a given color plane. It is a real number that represents percentage full and will read from 0 to 100%. This object obsoletes or replaces USAGE-AVERAGE-TONER-COVERAGE which could only be used for black toner coverage information. Additional information: The average percent of toner coverage for a specific color plane. The OID binding is the color plane. Only color planes which the printer supports will be available. This is only available if a hard disk is installed.ro OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.11.1.1 |
printer_average_marking_agent_coverage_sumThis object is used to read the accumulated sum of the percent coverage numbers calculated on a per page basis over the life of the printer. Additional information: The sum of the percent toner coverages for all impressions printed. The OID binding is the color plane. Only color planes which the printer supports will be available.ro OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.11.1.2 |
printer_average_marking_agent_coverage_sum_squaredThis object is used to read the accumulated sum of the squares of the percent coverage numbers calculated on a per page basis over the life of the printer. Additional information: The sum of the percent toner coverages squared for all impressions printed. The OID binding is the color plane. Only color planes which the printer supports will be available.ro OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.11.1.3 |
printer_average_marking_agent_units_per_gramThis object is used to read the marking agent units of measure per gram. This is typically a conversion factor for converting pixels of toner to grams. This pixels-per-gram value is used to calculate the estimated number of pages remaining for a given marking agent.ro OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.11.1.4 |
printer_average_marking_agent_coverage_actualThis object is used to read the actual average marking agent coverage for a given color plane. It is a real number that represents percent coverage and will read from 0 to 100%. This object will return the same value as PRINTER-AVERAGE-MARKING-AGENT-COVERAGE except under certain conditions which will be specified in the device POS. Additional information: This object will return the historical page coverage based on the specific supply requested. It is not based on the printers historical valuero OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.11.1.5 |
channel OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.6 |
channelnumberofchannelsAn indication of how many print data channels the I/O card supports. Additional information: This object is used by the IIO card to tell the peripheral firmware how many logical channels will be used by the card. This object can only be set once per physical channel. If an attempt is made to set it a subsequent time it is ignored and an return code of <ErrorActionCanNotBePerformedNow.is returned. If new firmware is dynamically downloaded to the Blazers Plus card, and if that firmware uses more logical channels, it is necessary to reset the printer.rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.6.1 |
channelprinteralertIdentifies the values of prtAlertIndex, prtAlertSeverityLevel, prtAlertGroup, prtAlertGroupIndex, prtAlertLocation, and prtAlertCode for the latest critical evnet in the prtAlertTable. The binary string is defined as following: <table> ----------------------------------------------------- Field | Filed | Description Offset | Length | ----------------------------------------------------- 0 | 4 | the value of prtAlertIndex 4 | 4 | the value of prtAlertSeverityLevel 8 | 4 | the value of prtAlertGroup 12 | 4 | the value of prtAlertGroupIndex 16 | 4 | the value of prtAlertLocation 20 | 4 | the value of prtAlertCode ------------------------------------------------------ </table> Each field is in Big Endian style. Additional information: This object is used to pass alert information from the peripheral to the IIO card. The standard printer MIB contains the following description: printerAlert TRAP-TYPE ENTERPRISE printerV1Alert VARIABLES { prtAlertIndex, prtAlertSeverityLevel, prtAlertGroup, prtAlertGroupIndex, prtAlertLocation, prtAlertCode } DESCRIPTION 'This trap is sent whenever a critical event is added to the prtAlertTable.' In order to provide this information in the trap packet, the IIO card enables traps on channelPrinterAlert. When a critical alert is generated the peripheral fills the appropriate value into this object and sends it to the card. This object is a structure which contains 24 bytes of data. The structure is: struct structAlertInfo { sint32 prtAlertIndex; sint32 prtAlertSeverityLevel; sint32 prtAlertGroup; sint32 prtAlertGroupIndex; sint32 prtAlertLocation; sint32 prtAlertCode; } thisAlertData;ro OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.6.2 |
channelTable SEQUENCE OF ChannelEntry .1.3.6.1.4.1.11.2.3.9.4.2.1.6.3 |
channelEntry ChannelEntry .1.3.6.1.4.1.11.2.3.9.4.2.1.6.3.1 |
channeltypeIdentifies the type of MIO print data channel. Additional information: After telling the peripheral how many logical channels will be used, the IIO card tells the printer the type of each of the channels. The type information is passed using the channelType object. Values are then saved by the peripheral and reported when users request the value of prtChannelType.rw Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.6.3.1.2 |
channelprotocolversionThe version of the protocol used on this MIO print data channel. Additional information: After telling the peripheral how many logical channels will be used, the IIO card tells the printer the protocol version of each of the channels. The protocol version information is passed using the channelProtocolVersion object. Values are then saved by the peripheral and reported when users request the value of prtChannelProtocolVersion.rw OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.6.3.1.3 |
channelstateThe state of this print data channel. The value determines whether control information and print data is allowed through this channel or not. Additional information: After telling the peripheral how many logical channels will be used, the IIO card tells the printer the state of each of the channels. The state can change from time to time. The state information is passed using the channelState object. Values are saved by the peripheral and reported when users request the value of prtChannelState.rw Enumeration .1.3.6.1.4.1.11.2.3.9.4.2.1.6.3.1.4 |
channelifindexThe value of ifIndex which corresponds to this channel. Additional information: After telling the peripheral how many logical channels will be used, the IIO card tells the printer the value of the IfIndex for each channel. The IfIndex is used as part of MIB-II. The values are saved by the peripheral and reported when users request the value of prtChannelIfIndex.rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.6.3.1.5 |
channelstatusSub-unit status is reported in the entries of the principle table in the Group that represents the sub-unit. For sub-units that report a status, there is a status column in the table and the value of this column is always an integer formed in the following way. The SubUnitStatus is an integer that is the sum of 5 distinct values, Availability, Non-Critical, Critical, On-line, and Transitioning. These values are: Availability value Available and Idle 0 000'b Available and Standby 2 010'b Available and Active 4 100'b Available and Busy 6 110'b Unavailable and OnRequest 1 001'b Unavailable because Broken 3 011'b Unknown 5 101'b Non-Critical No Non-Critical Alerts 0 Non-Critical Alerts 8 Critical No Critical Alerts 0 Critical Alerts 16 On-Line Intended state is On-Line 0 Intended state is Off-Line 32 Transitioning At intended state 0 Transitioning to intended state 64. Additional information: After telling the peripheral how many logical channels will be used, the IIO card tells the printer the status of each of the channels. The status can change from time to time. The status information is passed using the channelStatus object. Values are saved by the peripheral and reported when users request the value of prtChannelStatus.rw INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.6.3.1.6 |
channelinformationAuxiliary information to allow a printing application to use the channel for data submission to the printer. An application capable of using a specific PrtChannelType should be able to use the combined information from the prtChannelInformation and other channel and interface group objects to 'bootstrap' its use of the channel. prtChannelInformation is not intended to provide a general channel description, nor to provide information that is available once the channel is in use. The encoding and interpretation of the prtChannelInformation object is specific to channel type. The description of each prtChannelType enum value for which prtChannelInformation is defined specifies the appropriate encoding and interpretation, including interaction with other objects. For channel types that do not specify a prtChannelInformation value, its value shall be null (0 length). When a new prtChannelType enumeration value is registered, its accompanying description must specify the encoding and interpretation of the prtChannelInformation value for the channel type. prtChannelInformation semantics for an existing PrtChannelType may be added or amended in the same manner as described in section 2.4.1 for type 2 enumeration values. The prtChannelInformation specifies values for a collection of channel attributes, represented as text according to the following rules: 1. The prtChannelInformation is coded in the NVT ASCII character set. It is not affected by localization. 2. The prtChannelInformation is a list of entries representing the attribute values. Each entry consists of the following items, in order: a. a keyword, composed of alphabetic characters (A-Z, a-z), that identifies a channel attribute, b. an Equals Sign (=) to delimit the keyword, c. a data value, consisting of NVT ASCII graphics characters (codes 32-126), d. a Line Feed character (code 10) to delimit the data value. No other characters shall be present. Keywords are case-sensitive. Conventionally, keywords are capitalized (including each word of a multi-word keyword), and, since they occupy space in the prtChannelInformation, they are kept short. 3. If a channel attribute has multiple values, it is represented by multiple entries with the same keyword, each specifying one value. Otherwise, there shall be at most one entry for each attribute. 4. By default, entries may appear in any order. If there are ordering constraints for particular entries, these must be specified in their definitions. 5. The prtChannelInformation value may represent information that is not normally coded in textual form, or that is coded in a character set other than NVT ASCII. In these cases, whatever symbolic representation is conventionally used for the information should be used for encoding the prtChannelInformation. (For instance, a binary port value might be represented as a decimal number, Unicode would be represented in UTF-8 format.) 6. For each PrtChannelType for which prtChannelInformation entries are defined, the descriptive text associated with the PrtChannelType enumeration value shall specify the following information for each entry: Title: Brief description phrase, e.g.: 'Port name,'Service Name,' Keyword: The keyword value, eg: 'Port,' 'Service' Syntax: The encoding of the entry value, if it cannot be directly represented by NVT ASCII, Status: 'Mandatory,' 'Optional,' or 'Conditionally Mandatory,' Multiplicity: 'Single' or 'Multiple,' to indicate whether the entry may be present multiple times, Description: Description of the use of the entry, other information required to complete the definition (e.g.: ordering contstraints, interactions between entries). Applications that interpret prtChannelInformation should ignore unrecognized entries, so they are not affected if new entry types are added. Additional information: After telling the peripheral how many logical channels will be used, the IIO card tells the printer the value of the information value of each of the channels. The information is auxiliary information used in conjunction with the channel Type.rw OCTET STRING .1.3.6.1.4.1.11.2.3.9.4.2.1.6.3.1.7 |
tables OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.7 |
deviceChannelTable SEQUENCE OF DeviceChannelEntry .1.3.6.1.4.1.11.2.3.9.4.2.1.7.2 |
deviceChannelEntry DeviceChannelEntry .1.3.6.1.4.1.11.2.3.9.4.2.1.7.2.1 |
channel_bytes_sentThe low order 31 bits of the number of bytes sent from the printer to the host on this logical channel.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.7.2.1.2 |
channel_bytes_receivedThe low order 31 bits of the number of bytes received by the printer from the host on this logical channel.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.7.2.1.3 |
channel_io_errorsThe low order 31 bits of the number of I/O errors which have occured on this logical channel.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.7.2.1.4 |
channel_jobs_receivedThe low order 31 bits of the number of print jobs which have been received on this logical channel.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.7.2.1.5 |
channel_mioThe number of the MIO card associated with this logical channel. If this logical channel is not associated with an MIO card a zero is returned. The value returned for each logical channel is the MIO card's physical slot number. The list of supported values should be documented in the device POS. Additional information: The value returned will be zero for channels 1..3. If an MIOA card is installed, channels 4..10 will return a value of one or two. If an MIOB card is installed, channels 11..17 will return a value of one or two but not the same as channels 4..10. When two IIO cards are installed, the value returned by any channel 4..17 may change after the printer is power cycled.ro INTEGER .1.3.6.1.4.1.11.2.3.9.4.2.1.7.2.1.6 |