LANTRONIX-SLC-MIB
AI MIB Summary
The LANTRONIX-SLC-MIB enables SNMP-based monitoring and configuration of Lantronix Secure and Advanced Console Managers, specifically tracking serial port session states, device health parameters, and network interface statistics for out-of-band management infrastructure.
MIB module for managing Lantronix Secure Console Managers and Advanced Console Managers
Main OID:
slc.1.3.6.1.4.1.244.1.1
831
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
831 total| Object Name |
|---|
slcMIB module for managing Lantronix Secure Console Managers and Advanced Console Managers MODULE-IDENTITY .1.3.6.1.4.1.244.1.1 |
slcEvents OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.0 |
slcEventPowerSupplyThe SNMP trap that is generated when a power supply fails or is restored. NOTIFICATION-TYPE .1.3.6.1.4.1.244.1.1.0.1 |
slcEventSysadminPasswordThe SNMP trap that is generated when the sysadmin user password is changed. NOTIFICATION-TYPE .1.3.6.1.4.1.244.1.1.0.2 |
slcEventSLCShutdownThe SNMP trap that is generated when the SLC is shutdown. NOTIFICATION-TYPE .1.3.6.1.4.1.244.1.1.0.3 |
slcEventDevicePortDataThe SNMP trap that is generated when data is received on a Device Port, and the Device Port has been configured to generate a trap when a specified number of bytes (slcDevPortNumBytes) or a specified sequence of bytes (slcDevPortCfgEmailTextString) is received. slcDevPortData is the actual data received. NOTIFICATION-TYPE .1.3.6.1.4.1.244.1.1.0.4 |
slcEventDevicePortSLMDataThe SNMP trap that is generated when data is received on a Device Port, and the Device Port has been configured to generate a trap designated for the Secure Lantronix Management Appliance (SLM) when a specified number of bytes is received or a specified time frame is passed. This trap is only sent to the SLM. NOTIFICATION-TYPE .1.3.6.1.4.1.244.1.1.0.5 |
slcEventDevicePortSLMConfigThe SNMP trap that is generated when the SLM logging configuration is changed for a Device Port, and the Device Port has been configured to generate a trap designated for the Secure Lantronix Management Appliance (SLM). This trap specifies the new SLM logging configuration for the Device Port, and is only sent to the SLM. NOTIFICATION-TYPE .1.3.6.1.4.1.244.1.1.0.6 |
slcEventDevicePortDeviceLowTempThe SNMP trap that is generated when the low temperature limit for a sensor connected to a Device Port is exceeded. NOTIFICATION-TYPE .1.3.6.1.4.1.244.1.1.0.7 |
slcEventDevicePortDeviceHighTempThe SNMP trap that is generated when the high temperature limit for a sensor connected to a Device Port is exceeded. NOTIFICATION-TYPE .1.3.6.1.4.1.244.1.1.0.8 |
slcEventDevicePortDeviceLowHumidityThe SNMP trap that is generated when the low humidity limit for a sensor connected to a Device Port is exceeded. NOTIFICATION-TYPE .1.3.6.1.4.1.244.1.1.0.9 |
slcEventDevicePortDeviceHighHumidityThe SNMP trap that is generated when the high humidity limit for a sensor connected to a Device Port is exceeded. NOTIFICATION-TYPE .1.3.6.1.4.1.244.1.1.0.10 |
slcEventDevicePortDeviceErrorThe SNMP trap that is generated when an error occurs on a device connected to a Device Port. NOTIFICATION-TYPE .1.3.6.1.4.1.244.1.1.0.11 |
slcEventPCCardActionThe SNMP trap that is generated when an event occurs on one of the PC Card slots. NOTIFICATION-TYPE .1.3.6.1.4.1.244.1.1.0.12 |
slcEventSLCInternalTempThe SNMP trap that is generated when the internal temperature of the SLC is outside of the acceptable operating range. NOTIFICATION-TYPE .1.3.6.1.4.1.244.1.1.0.13 |
slcEventUSBActionThe SNMP trap that is generated when an event occurs on one of the USB Ports. NOTIFICATION-TYPE .1.3.6.1.4.1.244.1.1.0.14 |
slcEventDevicePortErrorThe SNMP trap that is generated when an error occurs on a a Device Port, or across all Device Ports. If an error occurs across all Device Ports, slcDevPortId will be 1 (one). NOTIFICATION-TYPE .1.3.6.1.4.1.244.1.1.0.15 |
slcEventSDCardActionThe SNMP trap that is generated when an event occurs on the SD Card slot. NOTIFICATION-TYPE .1.3.6.1.4.1.244.1.1.0.16 |
slcEventNoDialToneAlarmThe SNMP trap that is generated when an event indicates that a no-dial-tone condition on the internal modem exists. NOTIFICATION-TYPE .1.3.6.1.4.1.244.1.1.0.17 |
slcEventRPMActionThe SNMP trap that is generated when an event occurs on one of the Remote Power Manager (UPS or PDU) devices. NOTIFICATION-TYPE .1.3.6.1.4.1.244.1.1.0.18 |
slcEventPingHostFailsThe SNMP trap that is generated when the SLC is monitoring a host with regular pings and the SLC is unable to ping the host. The trap includes either the name or the IP address of the failed host. NOTIFICATION-TYPE .1.3.6.1.4.1.244.1.1.0.19 |
slcNetwork OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.1 |
slcNetEth OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.1.1 |
slcNetEthIfNumberThe number of entries in the Ethernet interface table.ro Integer32 .1.3.6.1.4.1.244.1.1.1.1.1 |
slcNetEthIfTableTable of Ethernet network entries. The number of entries is given by the value of slcNetEthIfNumber. SEQUENCE OF SlcNetEthIfEntry .1.3.6.1.4.1.244.1.1.1.1.2 |
slcNetEthIfEntryAn entry with the attributes for each Ethernet interface. Ethernet Port Eth1 is always index 1, and Eth2 is always index 2. SlcNetEthIfEntry .1.3.6.1.4.1.244.1.1.1.1.2.1 |
slcNetEthIfIndexReference index for each Ethernet interface.ro Integer32 .1.3.6.1.4.1.244.1.1.1.1.2.1.1 |
slcNetEthIfSourceThe state/source for the IP Address and subnet mask for the Ethernet interface.ro Enumeration .1.3.6.1.4.1.244.1.1.1.1.2.1.2 |
slcNetEthIfModeThe speed and duplex for the Ethernet interface.ro Enumeration .1.3.6.1.4.1.244.1.1.1.1.2.1.3 |
slcNetEthIfIPv6AddrThe IPv6 Address for each Ethernet interface.ro Ipv6Address (IPV6-TC) .1.3.6.1.4.1.244.1.1.1.1.2.1.4 |
slcNetEthIfIPv6PrefixLengthThe length of the prefix for slcNetEthIfIPv6Addr (in bits). INTEGER .1.3.6.1.4.1.244.1.1.1.1.2.1.5 |
slcNetEthIfMTUThe Maximum Transmission Unit for the Ethernet interface.ro Integer32 .1.3.6.1.4.1.244.1.1.1.1.2.1.6 |
slcNetEthIfMacAddressThe MAC Address for the Ethernet interface.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.244.1.1.1.1.2.1.7 |
slcNetEthGatewayThe gateway for routing non-Eth1 and non-Eth2 network IPv4 traffic.ro IpAddress .1.3.6.1.4.1.244.1.1.1.1.3 |
slcNetEthGatewayPrecedenceThe gateway to give precedence to, if both a static gateway is set, and a gateway is acquired via DHCP or a GPRS Modem.ro Enumeration .1.3.6.1.4.1.244.1.1.1.1.4 |
slcNetEthKeepaliveStartProbesTCP keepalive timer: number of seconds to wait before sending out the initial probe.ro Integer32 .1.3.6.1.4.1.244.1.1.1.1.5 |
slcNetEthKeepaliveNumberOfProbesTCP keepalive timer: number of probes to send out after the initial probe.ro Integer32 .1.3.6.1.4.1.244.1.1.1.1.6 |
slcNetEthKeepaliveIntervalTCP keepalive timer: number of seconds between probes.ro Integer32 .1.3.6.1.4.1.244.1.1.1.1.7 |
slcNetEthIPForwardingIf enabled, IP forwarding is used.ro EnabledState .1.3.6.1.4.1.244.1.1.1.1.8 |
slcNetEthDNS1The IPv4 Address of DNS server #1.ro IpAddress .1.3.6.1.4.1.244.1.1.1.1.9 |
slcNetEthDNS2The IPv4 Address of DNS server #2.ro IpAddress .1.3.6.1.4.1.244.1.1.1.1.10 |
slcNetEthDNS3The IPv4 Address of DNS server #3.ro IpAddress .1.3.6.1.4.1.244.1.1.1.1.11 |
slcNetEthDomainThe SLC domain name.ro OCTET STRING .1.3.6.1.4.1.244.1.1.1.1.12 |
slcNetEthAlternateGatewayThe alternate gateway for routing non-Eth1 and non-Eth2 network traffic. The alternate gateway is used if an IP Address usually accessible through the default gateway fails to return one or more pings.ro IpAddress .1.3.6.1.4.1.244.1.1.1.1.13 |
slcNetEthPingIPAddressThe IP Address to ping to determine if the alternate gateway should be used.ro IpAddress .1.3.6.1.4.1.244.1.1.1.1.14 |
slcNetEthPingInterfaceThe Ethernet interface used to determine if the alternate gateway should be used.ro Enumeration .1.3.6.1.4.1.244.1.1.1.1.15 |
slcNetEthPingDelayThe delay, in seconds, between pings used to determine if the alternate gateway should be used.ro Integer32 .1.3.6.1.4.1.244.1.1.1.1.16 |
slcNetEthPingFailedThe number of pings with no response required for the alternate gateway to be used.ro Integer32 .1.3.6.1.4.1.244.1.1.1.1.17 |
slcNetEthBondingThe Ethernet network redundancy/load balancing setting.ro Enumeration .1.3.6.1.4.1.244.1.1.1.1.18 |
slcNetEthIPv6If enabled, IPv6 is enabled.ro EnabledState .1.3.6.1.4.1.244.1.1.1.1.19 |
slcNetEthGatewayIPv6The default gateway for routing non-Eth1 and non-Eth2 IPv6 network traffic.ro Ipv6Address (IPV6-TC) .1.3.6.1.4.1.244.1.1.1.1.20 |
slcNetEthDNS1IPv6The IPv6 Address of DNS server #1.ro Ipv6Address (IPV6-TC) .1.3.6.1.4.1.244.1.1.1.1.21 |
slcNetEthDNS2IPv6The IPv6 Address of DNS server #2.ro Ipv6Address (IPV6-TC) .1.3.6.1.4.1.244.1.1.1.1.22 |
slcNetEthDNS3IPv6The IPv6 Address of DNS server #3.ro Ipv6Address (IPV6-TC) .1.3.6.1.4.1.244.1.1.1.1.23 |
slcNetEthPreferIPv4DNSIf enabled, IPv4 DNS records will be preferred when DNS hostname lookups are performed. Otherwise IPv6 records will be preferred (when IPv6 is enabled).ro EnabledState .1.3.6.1.4.1.244.1.1.1.1.24 |
slcNetFirewall OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.1.2 |
slcNetFirewallStateIf enabled, network traffic is filtered.ro EnabledState .1.3.6.1.4.1.244.1.1.1.2.1 |
slcNetFirewallRejectIf enabled, returns a 'connection denied' message on blocked ports. If disabled, ignores attempts to connect to a blocked port. This object is deprecated.roobsolete Enumeration .1.3.6.1.4.1.244.1.1.1.2.2 |
slcNetFirewallPingIf enabled, the SLC is invisible to pings. This object is deprecated.roobsolete EnabledState .1.3.6.1.4.1.244.1.1.1.2.3 |
slcNetFirewallSSHIf enabled, the SSH port is open. If disabled, the SSH port is blocked to network traffic. This object is deprecated.roobsolete EnabledState .1.3.6.1.4.1.244.1.1.1.2.4 |
slcNetFirewallTelnetIf enabled, the Telnet port is open. If disabled, the Telnet port is blocked to network traffic. This object is deprecated.roobsolete EnabledState .1.3.6.1.4.1.244.1.1.1.2.5 |
slcNetFirewallHTTPIf enabled, the HTTP port is open. If disabled, the HTTP port is blocked to network traffic. This object is deprecated.roobsolete EnabledState .1.3.6.1.4.1.244.1.1.1.2.6 |
slcNetFirewallHTTPSIf enabled, the HTTPS port is open. If disabled, the HTTPS port is blocked to network traffic. This object is deprecated.roobsolete EnabledState .1.3.6.1.4.1.244.1.1.1.2.7 |
slcNetFirewallSMBCIFSIf enabled, the SMBCIFS port is open. If disabled, the SMBCIFS port is blocked to network traffic. This object is deprecated.roobsolete EnabledState .1.3.6.1.4.1.244.1.1.1.2.8 |
slcNetFirewallRulesetNumberThe number of entries in the IP Filter Ruleset table.ro Integer32 .1.3.6.1.4.1.244.1.1.1.2.9 |
slcNetFirewallRulesetTableTable of IP Filter Rulesets. The number of entries is given by the value of slcNetFirewallRulesetNumber. SEQUENCE OF SlcNetFirewallRulesetEntry .1.3.6.1.4.1.244.1.1.1.2.10 |
slcNetFirewallRulesetEntryAn entry with all the attributes, including the rules, for an IP Filter Ruleset. SlcNetFirewallRulesetEntry .1.3.6.1.4.1.244.1.1.1.2.10.1 |
slcNetFirewallRulesetIndexReference index for each IP Filter Ruleset.ro Integer32 .1.3.6.1.4.1.244.1.1.1.2.10.1.1 |
slcNetFirewallRulesetNameThe name assigned to the IP Filter Ruleset.ro OCTET STRING .1.3.6.1.4.1.244.1.1.1.2.10.1.2 |
slcNetFirewallRulesetNumRulesThe number of rules in the slcNetFirewallRulesetRules string.ro Integer32 .1.3.6.1.4.1.244.1.1.1.2.10.1.3 |
slcNetFirewallRulesetRulesThe IP Filter rules that are defined for the Ruleset. The rule format is <IP>/<Mask Bits>;<Protocol>;<Ports>;<Action> and rules are separated by a colon. If the string is truncated because of system limitations, the string will be terminated with two colons.ro OCTET STRING .1.3.6.1.4.1.244.1.1.1.2.10.1.4 |
slcNetFirewallMappingNumberThe number of entries in the IP Filter Mapping table.ro Integer32 .1.3.6.1.4.1.244.1.1.1.2.11 |
slcNetFirewallMappingTableTable of mappings between IP Filter Rulesets and interfaces. The number of entries is given by the value of slcNetFirewallMappingNumber. SEQUENCE OF SlcNetFirewallMappingEntry .1.3.6.1.4.1.244.1.1.1.2.12 |
slcNetFirewallMappingEntryAn entry defining an interface that has an IP Filter Ruleset assigned to it. The interface can be either an Ethernet interface or a PC Card or Device Port modem. SlcNetFirewallMappingEntry .1.3.6.1.4.1.244.1.1.1.2.12.1 |
slcNetFirewallMappingIndexReference index for each IP Filter mapping.ro Integer32 .1.3.6.1.4.1.244.1.1.1.2.12.1.1 |
slcNetFirewallMappingIfacThe interface which has an IP Filter Ruleset assigned to it. If the interface is devicePort or usbPort, slcNetFirewallMappingIfacId defines which Device Port or USB Port (with an attached modem) the Ruleset is assigned to.ro Enumeration .1.3.6.1.4.1.244.1.1.1.2.12.1.2 |
slcNetFirewallMappingIfacIdThe identifier for a Device Port if slcNetFirewallMappingIfac equals devicePort(5), or the identifier for a USB Port if slcNetFirewallMappingIfac equals usbPort. Otherwise equals zero.ro Integer32 .1.3.6.1.4.1.244.1.1.1.2.12.1.3 |
slcNetFirewallMappingRulesetThe name of the IP Filter Ruleset assigned to the interface.ro OCTET STRING .1.3.6.1.4.1.244.1.1.1.2.12.1.4 |
slcNetRouting OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.1.3 |
slcNetRouteRIPStateIf enabled, the Routing Information Protocol (RIP) is used.ro EnabledState .1.3.6.1.4.1.244.1.1.1.3.1 |
slcNetRouteRIPVersionThe version of RIP being used.ro Enumeration .1.3.6.1.4.1.244.1.1.1.3.2 |
slcNetRouteStaticStateIf enabled, static routing is used.ro EnabledState .1.3.6.1.4.1.244.1.1.1.3.3 |
slcNetRouteStaticNumberThe number of entries in the Static Routes table.ro Integer32 .1.3.6.1.4.1.244.1.1.1.3.4 |
slcNetRouteStaticTableTable of static route entries. The number of entries is given by the value of slcNetRouteStaticNumber. SEQUENCE OF SlcNetRouteStaticEntry .1.3.6.1.4.1.244.1.1.1.3.5 |
slcNetRouteStaticEntryAn entry with the IP Address, subnet mask, and gateway for a static route. SlcNetRouteStaticEntry .1.3.6.1.4.1.244.1.1.1.3.5.1 |
slcNetRouteStaticIndexReference index for each static route.ro Integer32 .1.3.6.1.4.1.244.1.1.1.3.5.1.1 |
slcNetRouteStaticIPThe IP Address for the static route.ro IpAddress .1.3.6.1.4.1.244.1.1.1.3.5.1.2 |
slcNetRouteStaticMaskThe subnet mask for the static route.ro IpAddress .1.3.6.1.4.1.244.1.1.1.3.5.1.3 |
slcNetRouteStaticGatewayThe gateway for the static route.ro IpAddress .1.3.6.1.4.1.244.1.1.1.3.5.1.4 |
slcNetVPN OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.1.4 |
slcNetVPNTunnelIf enabled, the SLC is configured to initiate a VPN tunnel.ro EnabledState .1.3.6.1.4.1.244.1.1.1.4.1 |
slcNetVPNStatusA string giving the current status of the VPN tunnel.ro OCTET STRING .1.3.6.1.4.1.244.1.1.1.4.2 |
slcNetVPNNameThe name of the VPN tunnel.ro OCTET STRING .1.3.6.1.4.1.244.1.1.1.4.3 |
slcNetVPNEthPortThe Ethernet interface used for the VPN tunnel.ro Enumeration .1.3.6.1.4.1.244.1.1.1.4.4 |
slcNetVPNRemoteHostThe IP Address of the host on the remote side of the tunnel.ro IpAddress .1.3.6.1.4.1.244.1.1.1.4.5 |
slcNetVPNRemoteIdHow the remote host should be identified for authentication.ro OCTET STRING .1.3.6.1.4.1.244.1.1.1.4.6 |
slcNetVPNRemoteHopIf the remote host is behind a gateway, this specifies the IP Address of the gateway's public network interface.ro IpAddress .1.3.6.1.4.1.244.1.1.1.4.7 |
slcNetVPNRemoteSubnetOne or more subnets behind the remote host, expressed in CIDR notation (IP Address/mask bits). Multiple subnets are separated by a comma.ro OCTET STRING .1.3.6.1.4.1.244.1.1.1.4.8 |
slcNetVPNLocalIdHow the SLC should be identified for authentication.ro OCTET STRING .1.3.6.1.4.1.244.1.1.1.4.9 |
slcNetVPNLocalHopIf the SLC is behind a gateway, this specifies the IP Address of the gateway's public network interface.ro IpAddress .1.3.6.1.4.1.244.1.1.1.4.10 |
slcNetVPNLocalSubnetOne or more subnets behind the SLC, expressed in CIDR notation (IP Address/mask bits). Multiple subnets are separated by a comma.ro OCTET STRING .1.3.6.1.4.1.244.1.1.1.4.11 |
slcNetVPNIKENegotiationThe type of mode used by the SLC and the remote host for the IKE protocol, which exchanges security options between two hosts which want to communicate via IPSec.ro Enumeration .1.3.6.1.4.1.244.1.1.1.4.12 |
slcNetVPNIKEEncryptionThe type of encryption used for IKE negotiation.ro Enumeration .1.3.6.1.4.1.244.1.1.1.4.13 |
slcNetVPNIKEAuthenticationThe type of authentication used for IKE negotiation.ro Enumeration .1.3.6.1.4.1.244.1.1.1.4.14 |
slcNetVPNIKEDHGroupThe type of Diffie-Hellman Group used for IKE negotiation.ro Enumeration .1.3.6.1.4.1.244.1.1.1.4.15 |
slcNetVPNESPEncryptionThe type of encryption used for encrypting data sent through the tunnel.ro Enumeration .1.3.6.1.4.1.244.1.1.1.4.16 |
slcNetVPNESPAuthenticationThe type of authentication used for authenticating data sent through the VPN tunnel.ro Enumeration .1.3.6.1.4.1.244.1.1.1.4.17 |
slcNetVPNESPDHGroupThe type of Diffie-Hellman Group used for the key exchange for data sent through the tunnel.ro Enumeration .1.3.6.1.4.1.244.1.1.1.4.18 |
slcNetVPNAuthenticationThe type of authentication used by the host on each side of the tunnel to verify the identify of the other host.ro Enumeration .1.3.6.1.4.1.244.1.1.1.4.19 |
slcNetVPNPerfectForwardSecrecyWhen a new IPSec SA is negotiated after the IPSec SA lifetime expires, a new Diffie-Hellman key exchange can be performed to generate a new session key to be used to encrypt the data being sent through the tunnel. If this is enabled, it provides greater security, since the old session keys are destroyed.ro EnabledState .1.3.6.1.4.1.244.1.1.1.4.20 |
slcNetVPNModeConfigClientIf this is enabled, the SLC can receive network configuration from the remote host. This allows the remote host to assign an IP address/netmask to the SLC side of the VPN tunnel.ro EnabledState .1.3.6.1.4.1.244.1.1.1.4.21 |
slcNetVPNXAUTHClientIf this is enabled, the SLC will send authentication credentials to the remote host if they are requested. XAUTH, or Extended Authentication, can be used as an additional security measure on top of the Pre-Shared Key or RSA Public Key.ro EnabledState .1.3.6.1.4.1.244.1.1.1.4.22 |
slcNetVPNXAUTHClientLoginIf slcNetVPNXAUTHClientLogin is enabled, this is the login used for authentication.ro OCTET STRING .1.3.6.1.4.1.244.1.1.1.4.23 |
slcNetSecurity OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.1.5 |
slcNetSecurityFIPSModeIf enabled, the SLC is running in FIPS mode.ro EnabledState .1.3.6.1.4.1.244.1.1.1.5.1 |
slcServices OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.2 |
slcServNTP OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.2.1 |
slcServNTPStateIf enabled, NTP is used to synchronize SLC time with a network time server.ro EnabledState .1.3.6.1.4.1.244.1.1.2.1.1 |
slcServNTPSynchronizeThe method used by the SLC to synchronize time: receive broadcasts from the NTP server, or poll the NTP server.ro Enumeration .1.3.6.1.4.1.244.1.1.2.1.2 |
slcServNTPPollIf slcServNTPSynchronize is set to poll, indicates whether a local server or a public server is used as the NTP server.ro Enumeration .1.3.6.1.4.1.244.1.1.2.1.3 |
slcServNTPServerThe IPv4 Address of the local or public NTP server.ro IpAddress .1.3.6.1.4.1.244.1.1.2.1.4 |
slcServNTPLocalServer2The IPv4 Address of the 2nd local NTP server.ro IpAddress .1.3.6.1.4.1.244.1.1.2.1.5 |
slcServNTPLocalServer3The IPv4 Address of the 3rd local NTP server.ro IpAddress .1.3.6.1.4.1.244.1.1.2.1.6 |
slcServNTPServerIPv6The IPv6 Address of the local NTP server.ro Ipv6Address (IPV6-TC) .1.3.6.1.4.1.244.1.1.2.1.7 |
slcServNTPLocalServer2IPv6The IPv6 Address of the 2nd local NTP server.ro Ipv6Address (IPV6-TC) .1.3.6.1.4.1.244.1.1.2.1.8 |
slcServNTPLocalServer3IPv6The IPv6 Address of the 3rd local NTP server.ro Ipv6Address (IPV6-TC) .1.3.6.1.4.1.244.1.1.2.1.9 |
slcServSyslog OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.2.2 |
slcServSysNetworkLevelThe logging level for Network messages.ro SyslogLevel .1.3.6.1.4.1.244.1.1.2.2.1 |
slcServSysServicesLevelThe logging level for Services messages.ro SyslogLevel .1.3.6.1.4.1.244.1.1.2.2.2 |
slcServSysAuthLevelThe logging level for Authentication messages.ro SyslogLevel .1.3.6.1.4.1.244.1.1.2.2.3 |
slcServSysDevPortLevelThe logging level for Device Port messages.ro SyslogLevel .1.3.6.1.4.1.244.1.1.2.2.4 |
slcServSysDiagLevelThe logging level for Diagnostic messages.ro SyslogLevel .1.3.6.1.4.1.244.1.1.2.2.5 |
slcServSysGeneralLevelThe logging level for General system messages.ro SyslogLevel .1.3.6.1.4.1.244.1.1.2.2.6 |
slcServSysRemoteServerThe IPv4 Address of the remote Syslog Server.ro IpAddress .1.3.6.1.4.1.244.1.1.2.2.7 |
slcServSysRemoteServer2The IPv4 Address of the secondary remote Syslog Server.ro IpAddress .1.3.6.1.4.1.244.1.1.2.2.8 |
slcServSysRemoteServerIPv6The IPv6 Address of the remote Syslog Server.ro Ipv6Address (IPV6-TC) .1.3.6.1.4.1.244.1.1.2.2.9 |
slcServSysRemoteServer2IPv6The IPv6 Address of the secondary remote Syslog Server.ro Ipv6Address (IPV6-TC) .1.3.6.1.4.1.244.1.1.2.2.10 |
slcServSysRPMLogSizeThe maximum size in Kilobytes that RPM logs can grow to before they are pruned. When the file is pruned, it will be pruned to 50% of the RPM Log Size.ro Integer32 .1.3.6.1.4.1.244.1.1.2.2.11 |
slcServSysOtherLogSizeThe maximum size in Kilobytes that all logs other than RPM logs can grow to before they are pruned. When the file is pruned, it will be pruned to 50% of the RPM Log Size.ro Integer32 .1.3.6.1.4.1.244.1.1.2.2.12 |
slcServAuditLog OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.2.3 |
slcServAuditStateIf enabled, logs all configuration changes to an audit log.ro EnabledState .1.3.6.1.4.1.244.1.1.2.3.1 |
slcServAuditSizeThe maximum size of the audit login in Kilobytes.ro Integer32 .1.3.6.1.4.1.244.1.1.2.3.2 |
slcServAuditIncludeCLIIf enabled, all CLI commands are included in the audit log in addition to a description of the configuration change.ro EnabledState .1.3.6.1.4.1.244.1.1.2.3.3 |
slcServAuditInSystemLogIf enabled, all audit log entries are also sent to the system log.ro EnabledState .1.3.6.1.4.1.244.1.1.2.3.4 |
slcServSSH OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.2.4 |
slcServSSHStateIf enabled, allows logins to the SLC CLI via SSH.ro EnabledState .1.3.6.1.4.1.244.1.1.2.4.1 |
slcServSSHTimeoutThe timeout (in minutes) for SSH connections. A value of 0 indicates that timeouts are disabled.ro Integer32 .1.3.6.1.4.1.244.1.1.2.4.2 |
slcServSSHWebSSHIf enabled, allows Web SSH access to the CLI and the Device Ports.ro EnabledState .1.3.6.1.4.1.244.1.1.2.4.3 |
slcServSSHPortThe TCP Port number for incoming SSH sessions to the SLC CLI.ro Integer32 .1.3.6.1.4.1.244.1.1.2.4.4 |
slcServSSHV1IncomingIf enabled, incoming SSH version 1 connections are allowed.ro EnabledState .1.3.6.1.4.1.244.1.1.2.4.5 |
slcServSSHTimeoutDataDirectionIf slcServSSHTimeout is enabled, this setting indicates the direction of data used to determine if the connection has timed out.ro TimeoutDataDirection .1.3.6.1.4.1.244.1.1.2.4.6 |
slcServSSHDSAKeysIf enabled, SSH will support DSA keys for incoming and outgoing connections.ro EnabledState .1.3.6.1.4.1.244.1.1.2.4.7 |
slcServTelnet OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.2.5 |
slcServTelnetStateIf enabled, allows logins to the SLC CLI via Telnet.ro EnabledState .1.3.6.1.4.1.244.1.1.2.5.1 |
slcServTelnetTimeoutThe timeout (in minutes) for Telnet connections. A value of 0 indicates that timeouts are disabled.ro Integer32 .1.3.6.1.4.1.244.1.1.2.5.2 |
slcServTelnetWebTelnetIf enabled, allows Web Telnet access to the CLI and the Device Ports.ro EnabledState .1.3.6.1.4.1.244.1.1.2.5.3 |
slcServTelnetTelnetOutIf enabled, allows outgoing Telnet connections.ro EnabledState .1.3.6.1.4.1.244.1.1.2.5.4 |
slcServTelnetTimeoutDataDirectionIf slcServTelnetTimeout is enabled, this setting indicates the direction of data used to determine if the connection has timed out.ro TimeoutDataDirection .1.3.6.1.4.1.244.1.1.2.5.5 |
slcServSNMP OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.2.6 |
slcServSNMPStateEnables the SNMP agent on the SLC.ro EnabledState .1.3.6.1.4.1.244.1.1.2.6.1 |
slcServSNMPTrapsIf enabled, the SLC sends traps for key events.ro EnabledState .1.3.6.1.4.1.244.1.1.2.6.2 |
slcServSNMPNMSThe IPv4 Address of the Network Management System (NMS).ro IpAddress .1.3.6.1.4.1.244.1.1.2.6.3 |
slcServSNMPLocationThe SNMP location for the SLC.ro OCTET STRING .1.3.6.1.4.1.244.1.1.2.6.4 |
slcServSNMPContactThe SNMP contact for the SLC.ro OCTET STRING .1.3.6.1.4.1.244.1.1.2.6.5 |
slcServSNMPv3UserThe user name for read-only access to the SLC via SNMP v3.ro OCTET STRING .1.3.6.1.4.1.244.1.1.2.6.6 |
slcServSNMPReadOnlyCommunityThe SNMP read-only community for SNMP versions 1 and 2.ro OCTET STRING .1.3.6.1.4.1.244.1.1.2.6.7 |
slcServSNMPReadWriteCommunityThe SNMP read-write community for SNMP versions 1 and 2.ro OCTET STRING .1.3.6.1.4.1.244.1.1.2.6.8 |
slcServSNMPTrapCommunityThe SNMP trap community for SNMP versions 1 and 2.ro OCTET STRING .1.3.6.1.4.1.244.1.1.2.6.9 |
slcServSNMPAlarmDelayThe delay, in seconds, between traps that are sent out for alarm conditions.ro Integer32 .1.3.6.1.4.1.244.1.1.2.6.10 |
slcServSNMPv3ReadWriteUserThe user name for read-write access to the SLC via SNMP v3.ro OCTET STRING .1.3.6.1.4.1.244.1.1.2.6.11 |
slcServSNMPv3SecurityThe security model used for SNMP v3: insecure authentication and no packet encryption, secure authentication and no packet encryption, secure authentication and packet encryption.ro Enumeration .1.3.6.1.4.1.244.1.1.2.6.12 |
slcServSNMPv3AuthenticationWhen slcServSNMPv3Security is set to authNoEncrypt or authEncrypt, the type of authentication used.ro Enumeration .1.3.6.1.4.1.244.1.1.2.6.13 |
slcServSNMPv3EncryptionWhen slcServSNMPv3Security is set to authEncrypt, the type of encryption used.ro Enumeration .1.3.6.1.4.1.244.1.1.2.6.14 |
slcServSNMPv1v2If enabled, SNMP version 1 and version 2 (which use the Read-Only and Read-Write Communities) is enabled.ro EnabledState .1.3.6.1.4.1.244.1.1.2.6.15 |
slcServSNMPNMS2The IPv4 Address of the 2nd Network Management System (NMS).ro IpAddress .1.3.6.1.4.1.244.1.1.2.6.16 |
slcServSNMPNMSIPv6The IPv6 Address of the Network Management System (NMS).ro Ipv6Address (IPV6-TC) .1.3.6.1.4.1.244.1.1.2.6.17 |
slcServSNMPNMS2IPv6The IPv6 Address of the 2nd Network Management System (NMS).ro Ipv6Address (IPV6-TC) .1.3.6.1.4.1.244.1.1.2.6.18 |
slcServSMTP OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.2.7 |
slcServSMTPServerThe IP Address of the SMTP (email) server.ro IpAddress .1.3.6.1.4.1.244.1.1.2.7.1 |
slcServSMTPSenderThe sender's email address for emails sent from the SLC.ro OCTET STRING .1.3.6.1.4.1.244.1.1.2.7.2 |
slcServNFS OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.2.8 |
slcServNFSMountTableTable of NFS Mounts. SEQUENCE OF SlcServNFSMountEntry .1.3.6.1.4.1.244.1.1.2.8.1 |
slcServNFSMountEntryAn entry containing a NFS Mount and it's attributes. SlcServNFSMountEntry .1.3.6.1.4.1.244.1.1.2.8.1.1 |
slcServNFSMountIndexReference index for each NFS Mount.ro Integer32 .1.3.6.1.4.1.244.1.1.2.8.1.1.1 |
slcServNFSMountRemoteDirThe remote directory of the NFS Mount, in the format <remote server>:/<remote directory>.ro OCTET STRING .1.3.6.1.4.1.244.1.1.2.8.1.1.2 |
slcServNFSMountLocalDirThe directory in the SLC on which the remote directory is mounted.ro OCTET STRING .1.3.6.1.4.1.244.1.1.2.8.1.1.3 |
slcServNFSMountReadWriteIf enabled, the remote NFS directory is mounted read-write. If disabled, the remote NFS directory is mounted read-only.ro EnabledState .1.3.6.1.4.1.244.1.1.2.8.1.1.4 |
slcServNFSMountMountIf enabled, the remote NFS directory is configured to be mounted. If disabled, the remote NFS directory will not be mounted, or will be unmounted if is is mounted.ro EnabledState .1.3.6.1.4.1.244.1.1.2.8.1.1.5 |
slcServCIFS OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.2.9 |
slcServCIFSStateIf enabled, the SLC exports a CIFS share containing system logs, Device Port logs, and saved SLC configurations.ro EnabledState .1.3.6.1.4.1.244.1.1.2.9.1 |
slcServCIFSEth1If enabled, the CIFS share is exported on the Eth1 interface.ro EnabledState .1.3.6.1.4.1.244.1.1.2.9.2 |
slcServCIFSEth2If enabled, the CIFS share is exported on the Eth2 interface.ro EnabledState .1.3.6.1.4.1.244.1.1.2.9.3 |
slcServCIFSWorkgroupThe SMB/CIFS workgroup that the CIFS share is associated with.ro OCTET STRING .1.3.6.1.4.1.244.1.1.2.9.4 |
slcServSLCNetwork OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.2.10 |
slcServSLCNetSearchIndicates how to search for SLCs on the network: by searching a list of manually entered IP Addresses, by broadcasting on the local subnet, or both.ro Enumeration .1.3.6.1.4.1.244.1.1.2.10.1 |
slcServSLCNetNumberThe number of entries in the SLC Network Manual IP Address table.ro Integer32 .1.3.6.1.4.1.244.1.1.2.10.2 |
slcServSLCNetTableTable of manually entered IP Address entries. The number of entries is given by the value of slcServSLCNetNumber. SEQUENCE OF SlcServSLCNetEntry .1.3.6.1.4.1.244.1.1.2.10.3 |
slcServSLCNetEntryAn entry containing an IP Address for searching the SLC Network. SlcServSLCNetEntry .1.3.6.1.4.1.244.1.1.2.10.3.1 |
slcServSLCNetIndexReference index for each manual IP Address.ro Integer32 .1.3.6.1.4.1.244.1.1.2.10.3.1.1 |
slcServSLCNetIPThe IP Address to search for in the SLC Network.ro IpAddress .1.3.6.1.4.1.244.1.1.2.10.3.1.2 |
slcServPhoneHome OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.2.11 |
slcServPhoneHomeStateEnables the Phone Home feature.ro EnabledState .1.3.6.1.4.1.244.1.1.2.11.1 |
slcServPhoneHomeIPThe IP Address used for Phone Home communication.ro IpAddress .1.3.6.1.4.1.244.1.1.2.11.2 |
slcServHostList OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.2.12 |
slcServHostListNumberThe number of entries in the Host List table.ro Integer32 .1.3.6.1.4.1.244.1.1.2.12.1 |
slcServHostListTableTable of Host Lists. The number of entries is given by the value of slcServHostListNumber. SEQUENCE OF SlcServHostListEntry .1.3.6.1.4.1.244.1.1.2.12.2 |
slcServHostListEntryAn entry containing a Host List, used for Dial-in connections on a Device Port or PC Card modem. SlcServHostListEntry .1.3.6.1.4.1.244.1.1.2.12.2.1 |
slcServHostListIndexReference index for each Host List.ro Integer32 .1.3.6.1.4.1.244.1.1.2.12.2.1.1 |
slcServHostListNameThe unique name assigned to the Host List.ro OCTET STRING .1.3.6.1.4.1.244.1.1.2.12.2.1.2 |
slcServHostListRetryCountThe number of times to retry connections to an individual host within the Host List.ro Integer32 .1.3.6.1.4.1.244.1.1.2.12.2.1.3 |
slcServHostListAuthIf enabled, authentication is enabled for the hosts in the Host List.ro EnabledState .1.3.6.1.4.1.244.1.1.2.12.2.1.4 |
slcServHostListNumHostsThe number of individual hosts in the Host List.ro Integer32 .1.3.6.1.4.1.244.1.1.2.12.2.1.5 |
slcServHostListHostsA string containing all hosts in the Host List; the entry for each host is separated by a ';'. Each host entry is formatted as follows: '<Host>,<Protocol>,<TCP Port>,<Escape Sequence>;'.ro OCTET STRING .1.3.6.1.4.1.244.1.1.2.12.2.1.6 |
slcServWebTerm OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.2.13 |
slcServWebTermDeploymentThe method used to launch the Java Terminal for Web SSH and Web Telnet. This object is deprecated.ro Enumeration .1.3.6.1.4.1.244.1.1.2.13.1 |
slcServWebTermBufSizeThe number of lines in the Java Terminal buffer.ro Integer32 .1.3.6.1.4.1.244.1.1.2.13.2 |
slcServSite OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.2.14 |
slcServSiteNumberThe number of entries in the Sites table.ro Integer32 .1.3.6.1.4.1.244.1.1.2.14.1 |
slcServSiteTableTable of Sites. The number of entries is given by the value of slcServSiteNumber. SEQUENCE OF SlcServSiteEntry .1.3.6.1.4.1.244.1.1.2.14.2 |
slcServSiteEntryAn entry containing a Site, used for connections on a Device Port or PC Card/USB modem. SlcServSiteEntry .1.3.6.1.4.1.244.1.1.2.14.2.1 |
slcServSiteIndexReference index for each Site.ro Integer32 .1.3.6.1.4.1.244.1.1.2.14.2.1.1 |
slcServSiteNameThe unique name assigned to the Site.ro OCTET STRING .1.3.6.1.4.1.244.1.1.2.14.2.1.2 |
slcServSitePortThe port the Site is assigned to. If the port is devicePort or usbPort, slcServSitePortId defines which Device Port or USB Port (with an attached modem) the port is assigned to.ro Enumeration .1.3.6.1.4.1.244.1.1.2.14.2.1.3 |
slcServSitePortIdThe identifier for a Device Port if slcServSitePort equals devicePort(1), or the identifier for a USB Port if slcServSitePort equals usbPort(5). Otherwise equals zero.ro Integer32 .1.3.6.1.4.1.244.1.1.2.14.2.1.4 |
slcServSiteLoginHostFor PPP or text authentication on dialin, the user login or CHAP host to use for authentication. If authentication is successful, the rest of the site parameters will be used for the connection.ro OCTET STRING .1.3.6.1.4.1.244.1.1.2.14.2.1.5 |
slcServSiteCHAPSecretFor PPP authentication on dialin, the CHAP secret to use for authentication.ro OCTET STRING .1.3.6.1.4.1.244.1.1.2.14.2.1.6 |
slcServSiteTimeoutThe timeout (in minutes) for text connections. A value of 0 indicates that timeouts are disabled.ro Integer32 .1.3.6.1.4.1.244.1.1.2.14.2.1.7 |
slcServSiteLocalIPFor PPP connections, the local IP Address - all zeros if it should be negotiated.ro IpAddress .1.3.6.1.4.1.244.1.1.2.14.2.1.8 |
slcServSiteRemoteIPFor PPP connections, the remote IP Address - all zeros if it should be negotiated.ro IpAddress .1.3.6.1.4.1.244.1.1.2.14.2.1.9 |
slcServSiteStaticRouteIPFor Dial-on-Demand PPP connections, the static route IP Address for the remote network.ro IpAddress .1.3.6.1.4.1.244.1.1.2.14.2.1.10 |
slcServSiteStaticRouteMaskFor Dial-on-Demand PPP connections, the static route subnet mask for the remote network.ro IpAddress .1.3.6.1.4.1.244.1.1.2.14.2.1.11 |
slcServSiteStaticRouteGatewayFor Dial-on-Demand PPP connections, the static route gateway for the remote network.ro IpAddress .1.3.6.1.4.1.244.1.1.2.14.2.1.12 |
slcServSiteDialoutNumThe phone number to use for dial-out connections.ro OCTET STRING .1.3.6.1.4.1.244.1.1.2.14.2.1.13 |
slcServSiteDialoutLoginFor dial-out connections, the login to use for authenticating to the remote peer; or on dial-in, the login to use if the remote peer requests authentication (for example, a two way CHAP handshake).ro OCTET STRING .1.3.6.1.4.1.244.1.1.2.14.2.1.14 |
slcServSiteDialbackIf enabled, the site has permission to use modem dialback.ro EnabledState .1.3.6.1.4.1.244.1.1.2.14.2.1.15 |
slcServSiteDialbackNumThe phone number to use for dial-back connections.ro OCTET STRING .1.3.6.1.4.1.244.1.1.2.14.2.1.16 |
slcServSiteDialbackDelayFor Dial-back, specifies the delay between the dial-in and dial-out portion of the dialing sequence.ro Integer32 UNITS "seconds" .1.3.6.1.4.1.244.1.1.2.14.2.1.17 |
slcServSiteIdleTimeoutThe timeout (in seconds) for dial-in and dial-on-demand PPP connections. If no traffic is received for the PPP connection in the time defined by the idle timeout, the PPP connection will be terminated. A value of 0 indicates that timeouts are disabled.ro Integer32 UNITS "seconds" .1.3.6.1.4.1.244.1.1.2.14.2.1.18 |
slcServSiteRestartDelayThe delay (in seconds) to wait before restarting dial-out or dial-on-demand PPP connections.ro Integer32 UNITS "seconds" .1.3.6.1.4.1.244.1.1.2.14.2.1.19 |
slcServSiteCBCPServerAllowNoCallbackIf enabled, the SLC will allow the PPP peer to select the No Callback option during CBCP negotiation.ro EnabledState .1.3.6.1.4.1.244.1.1.2.14.2.1.20 |
slcServSiteNATStateIf enabled, use NAT (Network Address Translation) to allow dial-in and dial-back users to access the network connected to Eth1 and Eth2.ro EnabledState .1.3.6.1.4.1.244.1.1.2.14.2.1.21 |
slcServSiteDialbackRetriesFor Dial-back, specifies the number of times the SLC will retry the dial-out portion of the dialing sequence if the first attempt to dial-out fails.ro Integer32 .1.3.6.1.4.1.244.1.1.2.14.2.1.22 |
slcAuth OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.3 |
slcAuthLocal OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.3.1 |
slcAuthLocalNumberThe number of entries in the Local Users table.ro Integer32 .1.3.6.1.4.1.244.1.1.3.1.1 |
slcAuthLocalUsersTableTable of Local Users entries. The number of entries is given by the value of slcAuthLocalNumber. SEQUENCE OF SlcAuthLocalUserEntry .1.3.6.1.4.1.244.1.1.3.1.2 |
slcAuthLocalUserEntryAn entry containing a Local Users and it's attributes. SlcAuthLocalUserEntry .1.3.6.1.4.1.244.1.1.3.1.2.1 |
slcAuthLocalUserIndexReference index for each Local User.ro Integer32 .1.3.6.1.4.1.244.1.1.3.1.2.1.1 |
slcAuthLocalUserLoginThe login for the Local User. If the user account is locked (cannot login), the login is appended with a '*' character.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.1.2.1.2 |
slcAuthLocalUserUIDThe unique user identifier number for the Local User.ro Unsigned32 .1.3.6.1.4.1.244.1.1.3.1.2.1.3 |
slcAuthLocalUserListenPortsThe Device Ports and PC Card slots/USB ports which the Local User has permission to access via 'connect listen'.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.1.2.1.4 |
slcAuthLocalUserDataPortsThe Device Ports and PC Card slots/USB ports which the Local User has permission to access via 'connect direct'.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.1.2.1.5 |
slcAuthLocalUserClearPortsThe Device Ports and PC Card slots/USB ports which the Local User has permission to clear.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.1.2.1.6 |
slcAuthLocalUserEscapeSeqThe character sequence which the Local User uses to terminate connections to Device Ports.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.1.2.1.7 |
slcAuthLocalUserBreakSeqThe character sequence which the Local User uses to send a break sequence.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.1.2.1.8 |
slcAuthLocalUserMenuThe custom user menu defined for the Local User. If this is empty, there is no menu defined for the Local User. The menu name is followed by a slash '/' character and either a 'y' if the menu is automatically displayed at login, or a 'n' if it is not automatically displayed at login.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.1.2.1.9 |
slcAuthLocalUserDialbackIf enabled, the Local User has permission to use modem dialback.ro EnabledState .1.3.6.1.4.1.244.1.1.3.1.2.1.10 |
slcAuthLocalUserDialbackNumThe dialback number defined for the Local User.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.1.2.1.11 |
slcAuthLocalUserGroupThe group assigned to the Local User.ro UserGroup .1.3.6.1.4.1.244.1.1.3.1.2.1.12 |
slcAuthLocalUserRightsThe rights assigned to the Local User.ro UserRights .1.3.6.1.4.1.244.1.1.3.1.2.1.13 |
slcAuthLocalUserPwdExpiresIf enabled, the local user's password will expire.ro EnabledState .1.3.6.1.4.1.244.1.1.3.1.2.1.14 |
slcAuthLocalUserChangePwdIf enabled, the local user can change their password.ro EnabledState .1.3.6.1.4.1.244.1.1.3.1.2.1.15 |
slcAuthLocalUserChangePwdNextLoginIf enabled, the local user must change their password at their next login.ro EnabledState .1.3.6.1.4.1.244.1.1.3.1.2.1.16 |
slcAuthLocalStateIf enabled, Local Users are used for authentication.ro EnabledState .1.3.6.1.4.1.244.1.1.3.1.3 |
slcAuthLocalOrderThe authentication order of Local Users in authentication methods.ro AuthOrder .1.3.6.1.4.1.244.1.1.3.1.4 |
slcAuthLocalComplexPasswordsIf enabled, Local Users are required to use complex passwords that are at least 8 characters long and contain at least one uppercase character, one lowercase character, one digit, and one non-alphanumeric character.ro EnabledState .1.3.6.1.4.1.244.1.1.3.1.5 |
slcAuthLocalUseNextMethodThis object applies to all authentication methods, not just Local Users. If enabled, authentication will occur using all methods, in the order of their precedence, until a successful authentication occurs. If disabled, only the first authentication method that responds will be used.ro EnabledState .1.3.6.1.4.1.244.1.1.3.1.6 |
slcAuthLocalAllowReuseIf enabled, local users can reuse old passwords.ro EnabledState .1.3.6.1.4.1.244.1.1.3.1.7 |
slcAuthLocalReuseHistoryThe number of passwords a local user must use before reusing an old password.ro Integer32 .1.3.6.1.4.1.244.1.1.3.1.8 |
slcAuthLocalPasswordLifetimeThe number of days until a password expires.ro Integer32 .1.3.6.1.4.1.244.1.1.3.1.9 |
slcAuthLocalWarningPeriodThe number of days before a password expires that a local user is warned about the expiring password. A value of 0 indicates that this feature is disabled.ro Integer32 .1.3.6.1.4.1.244.1.1.3.1.10 |
slcAuthLocalMaxLoginAttemptsThe number of times a local user can attempt to log in unsuccessfully before the SLC locks the user out. A value of 0 indicates that this feature is disabled.ro Integer32 .1.3.6.1.4.1.244.1.1.3.1.11 |
slcAuthLocalLockoutPeriodThe number of minutes the locked-out user must wait before trying to log in to to the SLC again. A value of 0 indicates that this feature is disabled.ro Integer32 .1.3.6.1.4.1.244.1.1.3.1.12 |
slcAuthLocalMultipleSysadminLoginsIf enabled, multiple sysadmin logins to the web are allowed.ro EnabledState .1.3.6.1.4.1.244.1.1.3.1.13 |
slcAuthLocalSysadminConsoleOnlyIf enabled, the sysadmin can only access the SLC via the Console Port.ro EnabledState .1.3.6.1.4.1.244.1.1.3.1.14 |
slcAuthNIS OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.3.2 |
slcAuthNISStateIf enabled, NIS is used for authentication.ro EnabledState .1.3.6.1.4.1.244.1.1.3.2.1 |
slcAuthNISOrderThe authentication order of NIS in remote authentication methods.ro AuthOrder .1.3.6.1.4.1.244.1.1.3.2.2 |
slcAuthNISDomainThe NIS domain.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.2.3 |
slcAuthNISBroadcastIf enabled, the SLC broadcasts for the NIS server.ro EnabledState .1.3.6.1.4.1.244.1.1.3.2.4 |
slcAuthNISMasterThe IP Address of the NIS master server.ro IpAddress .1.3.6.1.4.1.244.1.1.3.2.5 |
slcAuthNISSlave1The IP Address of the NIS slave server #1.ro IpAddress .1.3.6.1.4.1.244.1.1.3.2.6 |
slcAuthNISSlave2The IP Address of the NIS slave server #2.ro IpAddress .1.3.6.1.4.1.244.1.1.3.2.7 |
slcAuthNISSlave3The IP Address of the NIS slave server #3.ro IpAddress .1.3.6.1.4.1.244.1.1.3.2.8 |
slcAuthNISGroupThe group assigned to NIS users who login to the SLC and do not have group/rights defined in the Remote User database.ro UserGroup .1.3.6.1.4.1.244.1.1.3.2.9 |
slcAuthNISRightsThe rights assigned to NIS users who login to the SLC and do not have group/rights defined in the Remote User database.ro UserRights .1.3.6.1.4.1.244.1.1.3.2.10 |
slcAuthNISMenuThe custom user menu defined for all NIS users who login to the SLC. If this is empty, there is no menu defined for NIS Users.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.2.11 |
slcAuthNISListenPortsThe Device Ports and PC Card slots/USB ports which users authenticated via NIS have permission to access via 'connect listen'.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.2.12 |
slcAuthNISDataPortsThe Device Ports and PC Card slots/USB ports which users authenticated via NIS have permission to access via 'connect direct'.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.2.13 |
slcAuthNISClearPortsThe Device Ports and PC Card slots/USB ports which users authenticated via NIS have permission to clear.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.2.14 |
slcAuthNISSlave4The IP Address of the NIS slave server #4.ro IpAddress .1.3.6.1.4.1.244.1.1.3.2.15 |
slcAuthNISSlave5The IP Address of the NIS slave server #5.ro IpAddress .1.3.6.1.4.1.244.1.1.3.2.16 |
slcAuthNISEscapeSeqThe character sequence which the NIS user uses to terminate connections to Device Ports.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.2.17 |
slcAuthNISBreakSeqThe character sequence which the NIS user uses to send a break sequence.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.2.18 |
slcAuthNISDialbackIf enabled, NIS users have permission to use modem dialback.ro EnabledState .1.3.6.1.4.1.244.1.1.3.2.19 |
slcAuthNISDialbackNumThe dialback number defined for NIS users.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.2.20 |
slcAuthLDAP OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.3.3 |
slcAuthLDAPStateIf enabled, LDAP is used for authentication.ro EnabledState .1.3.6.1.4.1.244.1.1.3.3.1 |
slcAuthLDAPOrderThe authentication order of LDAP in remote authentication methods.ro AuthOrder .1.3.6.1.4.1.244.1.1.3.3.2 |
slcAuthLDAPServerThe IPv4 Address of the LDAP server.ro IpAddress .1.3.6.1.4.1.244.1.1.3.3.3 |
slcAuthLDAPBaseThe LDAP Base.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.3.4 |
slcAuthLDAPBindNameThe LDAP Bind Name.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.3.5 |
slcAuthLDAPPortThe LDAP TCP Port Number.ro Integer32 .1.3.6.1.4.1.244.1.1.3.3.6 |
slcAuthLDAPADSupportIf enabled, Active Directory support is enabled for LDAP.ro EnabledState .1.3.6.1.4.1.244.1.1.3.3.7 |
slcAuthLDAPGroupThe group assigned to LDAP users who login to the SLC and do not have group/rights defined in the Remote User database.ro UserGroup .1.3.6.1.4.1.244.1.1.3.3.8 |
slcAuthLDAPRightsThe rights assigned to LDAP users who login to the SLC and do not have group/rights defined in the Remote User database.ro UserRights .1.3.6.1.4.1.244.1.1.3.3.9 |
slcAuthLDAPMenuThe custom user menu defined for all LDAP users who login to the SLC. If this is empty, there is no menu defined for LDAP Users.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.3.10 |
slcAuthLDAPListenPortsThe Device Ports and PC Card slots/USB ports which users authenticated via LDAP have permission to access via 'connect listen'.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.3.11 |
slcAuthLDAPDataPortsThe Device Ports and PC Card slots/USB ports which users authenticated via LDAP have permission to access via 'connect direct'.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.3.12 |
slcAuthLDAPClearPortsThe Device Ports and PC Card slots/USB ports which users authenticated via LDAP have permission to clear.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.3.13 |
slcAuthLDAPEncryptIf enabled, encrypt messages between the SLC and the LDAP server.ro EnabledState .1.3.6.1.4.1.244.1.1.3.3.14 |
slcAuthLDAPEscapeSeqThe character sequence which the LDAP user uses to terminate connections to Device Ports.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.3.15 |
slcAuthLDAPBreakSeqThe character sequence which the LDAP user uses to send a break sequence.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.3.16 |
slcAuthLDAPBindWithLoginIf enabled, bind to the LDAP server using the current login and password. The $login token in slcAuthLDAPBindName will be replaced with the current login.ro EnabledState .1.3.6.1.4.1.244.1.1.3.3.17 |
slcAuthLDAPUseLDAPSchemaIf enabled, attributes and permissions for remote users are retrieved from an LDAP server.ro EnabledState .1.3.6.1.4.1.244.1.1.3.3.18 |
slcAuthLDAPDialbackIf enabled, LDAP users have permission to use modem dialback.ro EnabledState .1.3.6.1.4.1.244.1.1.3.3.19 |
slcAuthLDAPDialbackNumThe dialback number defined for LDAP users.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.3.20 |
slcAuthLDAPUserFilterThe attribute used by the LDAP server for user logins.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.3.21 |
slcAuthLDAPGroupFilterThe objectclass used by the LDAP server for groups.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.3.22 |
slcAuthLDAPGroupMembershipAttrThe attribute used by the LDAP server for group membership. This attribute may be use to search for a name (ie, msmith) or a Distinguished Name (ie, uid=msmith,ou=People,dc=lantronix,dc=com).ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.3.23 |
slcAuthLDAPGroupMembershipDNIf enabled, the string given by slcAuthLDAPGroupMembershipAttr is a Distinguished Name (DN). Otherwise the string is a name.ro EnabledState .1.3.6.1.4.1.244.1.1.3.3.24 |
slcAuthLDAPServer2The IPv4 Address of the secondary/backup LDAP server.ro IpAddress .1.3.6.1.4.1.244.1.1.3.3.25 |
slcAuthLDAPServerIPv6The IPv6 Address of the LDAP server.ro Ipv6Address (IPV6-TC) .1.3.6.1.4.1.244.1.1.3.3.26 |
slcAuthLDAPServer2IPv6The IPv6 Address of the secondary/backup LDAP server.ro Ipv6Address (IPV6-TC) .1.3.6.1.4.1.244.1.1.3.3.27 |
slcAuthRADIUS OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.3.4 |
slcAuthRADIUSStateIf enabled, RADIUS is used for authentication.ro EnabledState .1.3.6.1.4.1.244.1.1.3.4.1 |
slcAuthRADIUSOrderThe authentication order of RADIUS in remote authentication methods.ro AuthOrder .1.3.6.1.4.1.244.1.1.3.4.2 |
slcAuthRADIUSTimeoutThe RADIUS Timeout in seconds. A value of 0 indicates that timeouts are disabled.ro Integer32 .1.3.6.1.4.1.244.1.1.3.4.3 |
slcAuthRADIUSServerTableTable of RADIUS servers. SEQUENCE OF SlcAuthRADIUSServerEntry .1.3.6.1.4.1.244.1.1.3.4.4 |
slcAuthRADIUSServerEntryAn entry containing a RADIUS server and it's parameters. SlcAuthRADIUSServerEntry .1.3.6.1.4.1.244.1.1.3.4.4.1 |
slcAuthRADIUSServerIndexReference index for each RADIUS server.ro Integer32 .1.3.6.1.4.1.244.1.1.3.4.4.1.1 |
slcAuthRADIUSServerThe IPv4 Address of the RADIUS server.ro IpAddress .1.3.6.1.4.1.244.1.1.3.4.4.1.2 |
slcAuthRADIUSPortThe RADIUS Server TCP Port Number.ro Integer32 .1.3.6.1.4.1.244.1.1.3.4.4.1.3 |
slcAuthRADIUSServerIPv6The IPv6 Address of the RADIUS server.ro Ipv6Address (IPV6-TC) .1.3.6.1.4.1.244.1.1.3.4.4.1.4 |
slcAuthRADIUSGroupThe group assigned to RADIUS users who login to the SLC and do not have group/rights defined in the Remote User database.ro UserGroup .1.3.6.1.4.1.244.1.1.3.4.5 |
slcAuthRADIUSRightsThe rights assigned to RADIUS users who login to the SLC and do not have group/rights defined in the Remote User database.ro UserRights .1.3.6.1.4.1.244.1.1.3.4.6 |
slcAuthRADIUSMenuThe custom user menu defined for all RADIUS users who login to the SLC. If this is empty, there is no menu defined for RADIUS Users.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.4.7 |
slcAuthRADIUSListenPortsThe Device Ports and PC Card slots/USB ports which users authenticated via RADIUS have permission to access via 'connect listen'.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.4.8 |
slcAuthRADIUSDataPortsThe Device Ports and PC Card slots/USB ports which users authenticated via RADIUS have permission to access via 'connect direct'.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.4.9 |
slcAuthRADIUSClearPortsThe Device Ports and PC Card slots/USB ports which users authenticated via RADIUS have permission to clear.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.4.10 |
slcAuthRADIUSEscapeSeqThe character sequence which the RADIUS user uses to terminate connections to Device Ports.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.4.11 |
slcAuthRADIUSBreakSeqThe character sequence which the RADIUS user uses to send a break sequence.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.4.12 |
slcAuthRADIUSDialbackIf enabled, RADIUS users have permission to use modem dialback.ro EnabledState .1.3.6.1.4.1.244.1.1.3.4.13 |
slcAuthRADIUSDialbackNumThe dialback number defined for RADIUS users.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.4.14 |
slcAuthRADIUSUseVSAIf enabled, the SLC will obtain remote user attributes (group/permissions and port access) from the RADIUS server via the Vendor-Specific Attribute (VSA).ro EnabledState .1.3.6.1.4.1.244.1.1.3.4.15 |
slcAuthKerberos OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.3.5 |
slcAuthKerbStateIf enabled, Kerberos is used for authentication.ro EnabledState .1.3.6.1.4.1.244.1.1.3.5.1 |
slcAuthKerbOrderThe authentication order of Kerberos in remote authentication methods.ro AuthOrder .1.3.6.1.4.1.244.1.1.3.5.2 |
slcAuthKerbRealmThe Kerberos Realm.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.5.3 |
slcAuthKerbKDCThe Kerberos KDC.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.5.4 |
slcAuthKerbKDCIPThe IPv4 Address of the Kerberos Key Distribution Server.ro IpAddress .1.3.6.1.4.1.244.1.1.3.5.5 |
slcAuthKerbKDCPortThe Kerberos KDC Port Number.ro Integer32 .1.3.6.1.4.1.244.1.1.3.5.6 |
slcAuthKerbUseLDAPIf enabled, LDAP is used for lookups.ro EnabledState .1.3.6.1.4.1.244.1.1.3.5.7 |
slcAuthKerbGroupThe group assigned to Kerberos users who login to the SLC and do not have group/rights defined in the Remote User database.ro UserGroup .1.3.6.1.4.1.244.1.1.3.5.8 |
slcAuthKerbRightsThe rights assigned to Kerberos users who login to the SLC and do not have group/rights defined in the Remote User database.ro UserRights .1.3.6.1.4.1.244.1.1.3.5.9 |
slcAuthKerbMenuThe custom user menu defined for all Kerberos users who login to the SLC. If this is empty, there is no menu defined for Kerberos Users.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.5.10 |
slcAuthKerbListenPortsThe Device Ports and PC Card slots/USB ports which users authenticated via Kerberos have permission to access via 'connect listen'.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.5.11 |
slcAuthKerbDataPortsThe Device Ports and PC Card slots/USB ports which users authenticated via Kerberos have permission to access via 'connect direct'.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.5.12 |
slcAuthKerbClearPortsThe Device Ports and PC Card slots/USB ports which users authenticated via Kerberos have permission to clear.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.5.13 |
slcAuthKerbEscapeSeqThe character sequence which the Kerberos user uses to terminate connections to Device Ports.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.5.14 |
slcAuthKerbBreakSeqThe character sequence which the Kerberos user uses to send a break sequence.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.5.15 |
slcAuthKerbDialbackIf enabled, Kerberos users have permission to use modem dialback.ro EnabledState .1.3.6.1.4.1.244.1.1.3.5.16 |
slcAuthKerbDialbackNumThe dialback number defined for Kerberos users.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.5.17 |
slcAuthKerbKDCIPv6The IPv6 Address of the Kerberos Key Distribution Server.ro Ipv6Address (IPV6-TC) .1.3.6.1.4.1.244.1.1.3.5.18 |
slcAuthTACACS OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.3.6 |
slcAuthTACACSStateIf enabled, TACACS is used for authentication.ro EnabledState .1.3.6.1.4.1.244.1.1.3.6.1 |
slcAuthTACACSOrderThe authentication order of TACACS in remote authentication methods.ro AuthOrder .1.3.6.1.4.1.244.1.1.3.6.2 |
slcAuthTACACSServerThe IPv4 Address of the first TACACS server.ro IpAddress .1.3.6.1.4.1.244.1.1.3.6.3 |
slcAuthTACACSEncryptIf enabled, encrypt messages between the SLC and the TACACS server.ro EnabledState .1.3.6.1.4.1.244.1.1.3.6.4 |
slcAuthTACACSGroupThe group assigned to TACACS users who login to the SLC and do not have group/rights defined in the Remote User database.ro UserGroup .1.3.6.1.4.1.244.1.1.3.6.5 |
slcAuthTACACSRightsThe rights assigned to TACACS users who login to the SLC and do not have group/rights defined in the Remote User database.ro UserRights .1.3.6.1.4.1.244.1.1.3.6.6 |
slcAuthTACACSMenuThe custom user menu defined for all TACACS users who login to the SLC. If this is empty, there is no menu defined for TACACS Users.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.6.7 |
slcAuthTACACSListenPortsThe Device Ports and PC Card slots/USB ports which users authenticated via TACACS have permission to access via 'connect listen'.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.6.8 |
slcAuthTACACSDataPortsThe Device Ports and PC Card slots/USB ports which users authenticated via TACACS have permission to access via 'connect direct'.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.6.9 |
slcAuthTACACSClearPortsThe Device Ports and PC Card slots/USB ports which users authenticated via TACACS have permission to clear.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.6.10 |
slcAuthTACACSServer2The IPv4 Address of the second TACACS server.ro IpAddress .1.3.6.1.4.1.244.1.1.3.6.11 |
slcAuthTACACSServer3The IPv4 Address of the third TACACS server.ro IpAddress .1.3.6.1.4.1.244.1.1.3.6.12 |
slcAuthTACACSEscapeSeqThe character sequence which the TACACS user uses to terminate connections to Device Ports.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.6.13 |
slcAuthTACACSBreakSeqThe character sequence which the TACACS user uses to send a break sequence.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.6.14 |
slcAuthTACACSDialbackIf enabled, TACACS users have permission to use modem dialback.ro EnabledState .1.3.6.1.4.1.244.1.1.3.6.15 |
slcAuthTACACSDialbackNumThe dialback number defined for TACACS users.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.6.16 |
slcAuthTACACSAuthServiceThe type of service used to pass the authentications tokens (e.g., login and password) between the SLC and the TACACS+ server.ro Enumeration .1.3.6.1.4.1.244.1.1.3.6.17 |
slcAuthTACACSServerIPv6The IPv6 Address of the first TACACS server.ro Ipv6Address (IPV6-TC) .1.3.6.1.4.1.244.1.1.3.6.18 |
slcAuthTACACSServer2IPv6The IPv6 Address of the second TACACS server.ro Ipv6Address (IPV6-TC) .1.3.6.1.4.1.244.1.1.3.6.19 |
slcAuthTACACSServer3IPv6The IPv6 Address of the third TACACS server.ro Ipv6Address (IPV6-TC) .1.3.6.1.4.1.244.1.1.3.6.20 |
slcAuthRemote OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.3.7 |
slcAuthRemoteNumberThe number of entries in the Remote Users table.ro Integer32 .1.3.6.1.4.1.244.1.1.3.7.1 |
slcAuthRemoteUsersTableTable of Remote Users entries. The number of entries is given by the value of slcAuthRemoteNumber. SEQUENCE OF SlcAuthRemoteUserEntry .1.3.6.1.4.1.244.1.1.3.7.2 |
slcAuthRemoteUserEntryAn entry containing a Remote User and its attributes. SlcAuthRemoteUserEntry .1.3.6.1.4.1.244.1.1.3.7.2.1 |
slcAuthRemoteUserIndexReference index for each Remote User.ro Integer32 .1.3.6.1.4.1.244.1.1.3.7.2.1.1 |
slcAuthRemoteUserLoginThe login for the Remote User.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.7.2.1.2 |
slcAuthRemoteUserGroupThe group assigned to the Remote User.ro UserGroup .1.3.6.1.4.1.244.1.1.3.7.2.1.3 |
slcAuthRemoteUserRightsThe rights assigned to the Remote User.ro UserRights .1.3.6.1.4.1.244.1.1.3.7.2.1.4 |
slcAuthRemoteUserListenPortsThe Device Ports and PC Card slots/USB ports which the Remote User has permission to access via 'connect listen'.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.7.2.1.5 |
slcAuthRemoteUserDataPortsThe Device Ports and PC Card slots/USB ports which the Remote User has permission to access via 'connect direct'.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.7.2.1.6 |
slcAuthRemoteUserClearPortsThe Device Ports and PC Card slots/USB ports which the Remote User has permission to clear.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.7.2.1.7 |
slcAuthRemoteUserEscapeSeqThe character sequence which the Remote User uses to terminate connections to Device Ports.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.7.2.1.8 |
slcAuthRemoteUserBreakSeqThe character sequence which the Remote User uses to send a break sequence.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.7.2.1.9 |
slcAuthRemoteUserMenuThe custom user menu defined for the Remote User. If this is empty, there is no menu defined for the Remote User. The menu name is followed by a slash '/' character and either a 'y' if the menu is automatically displayed at login, or a 'n' if it is not automatically displayed at login.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.7.2.1.10 |
slcAuthRemoteUserLockedIf enabled, the Remote User's account is locked (blocked).ro EnabledState .1.3.6.1.4.1.244.1.1.3.7.2.1.11 |
slcAuthRemoteUserDialbackIf enabled, the Remote User has permission to use modem dialback.ro EnabledState .1.3.6.1.4.1.244.1.1.3.7.2.1.12 |
slcAuthRemoteUserDialbackNumThe dialback number defined for the Remote User.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.7.2.1.13 |
slcAuthRemoteAuthListOnlyIf enabled, remote users who log into the SLC will only be authenticated if they are listed in the remote user list.ro EnabledState .1.3.6.1.4.1.244.1.1.3.7.3 |
slcAuthGroups OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.3.8 |
slcAuthGroupsNumberThe number of entries in the Groups table.ro Integer32 .1.3.6.1.4.1.244.1.1.3.8.1 |
slcAuthGroupsTableTable of Groups entries. The number of entries is given by the value of slcAuthGroupsNumber. SEQUENCE OF SlcAuthGroupEntry .1.3.6.1.4.1.244.1.1.3.8.2 |
slcAuthGroupEntryAn entry containing a Remote User and its attributes. SlcAuthGroupEntry .1.3.6.1.4.1.244.1.1.3.8.2.1 |
slcAuthGroupIndexReference index for each Group.ro Integer32 .1.3.6.1.4.1.244.1.1.3.8.2.1.1 |
slcAuthGroupNameThe name for the Group.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.8.2.1.2 |
slcAuthGroupRightsThe rights assigned to the Group.ro UserRights .1.3.6.1.4.1.244.1.1.3.8.2.1.3 |
slcAuthGroupListenPortsThe Device Ports and PC Card slots/USB ports which the Group has permission to access via 'connect listen'.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.8.2.1.4 |
slcAuthGroupDataPortsThe Device Ports and PC Card slots/USB ports which the Group has permission to access via 'connect direct'.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.8.2.1.5 |
slcAuthGroupClearPortsThe Device Ports and PC Card slots/USB ports which the Group has permission to clear.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.8.2.1.6 |
slcAuthGroupEscapeSeqThe character sequence which the Group uses to terminate connections to Device Ports.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.8.2.1.7 |
slcAuthGroupBreakSeqThe character sequence which the Group uses to send a break sequence.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.8.2.1.8 |
slcAuthGroupMenuThe custom user menu defined for the Group. If this is empty, there is no menu defined for the Group. The menu name is followed by a slash '/' character and either a 'y' if the menu is automatically displayed at login, or a 'n' if it is not automatically displayed at login.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.8.2.1.9 |
slcAuthGroupDialbackIf enabled, the Group has permission to use modem dialback.ro EnabledState .1.3.6.1.4.1.244.1.1.3.8.2.1.10 |
slcAuthGroupDialbackNumThe dialback number defined for the Group.ro OCTET STRING .1.3.6.1.4.1.244.1.1.3.8.2.1.11 |
slcDevices OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.4 |
slcDevConsolePort OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.4.1 |
slcDevConBaudThe baud rate of the Console Port.ro Integer32 ( 300 | 600 | 1200 | 2400 | 4800 | 9600 | 19200 | 38400 | 57600 | 115200 ) .1.3.6.1.4.1.244.1.1.4.1.1 |
slcDevConDataBitsThe data bits of the Console Port.ro Integer32 ( 7 | 8 ) .1.3.6.1.4.1.244.1.1.4.1.2 |
slcDevConStopBitsThe stop bits of the Console Port.ro Integer32 ( 1 | 2 ) .1.3.6.1.4.1.244.1.1.4.1.3 |
slcDevConParityThe parity of the Console Port.ro Enumeration .1.3.6.1.4.1.244.1.1.4.1.4 |
slcDevConFlowControlThe flow control of the Console Port.ro Enumeration .1.3.6.1.4.1.244.1.1.4.1.5 |
slcDevConTimeoutThe timeout (in minutes) for logins to the Console Port. A value of 0 indicates that timeouts are disabled.ro Integer32 .1.3.6.1.4.1.244.1.1.4.1.6 |
slcDevConShowLinesIf enabled, upon connecting to the Console Port, a series of characters (or lines) output to the Console Port before it was connected to are displayed.ro EnabledState .1.3.6.1.4.1.244.1.1.4.1.7 |
slcDevConNumberShowLinesIf slcDevConShowLines is enabled, the number of lines that are displayed upon connecting to the Console Port.ro Integer32 .1.3.6.1.4.1.244.1.1.4.1.8 |
slcDevConGroupThe group or groups that may access the Console Port.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.1.9 |
slcDevDevicePorts OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.4.2 |
slcDevPortGlobal OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.4.2.1 |
slcDevGlobalListenPortsThe Device Ports which remotely authenticated users have permission to access via 'connect listen'. This object has been replaced by permissions for each remote authentication method: slcAuthNISListenPorts, slcAuthLDAPListenPorts, slcAuthRADIUSListenPorts, slcAuthKerbListenPorts, slcAuthTACACSListenPorts.roobsolete OCTET STRING .1.3.6.1.4.1.244.1.1.4.2.1.1 |
slcDevGlobalDataPortsThe Device Ports which remotely authenticated users have permission to access via 'connect direct'. This object has been replaced by permissions for each remote authentication method: slcAuthNISDataPorts, slcAuthLDAPDataPorts, slcAuthRADIUSDataPorts, slcAuthKerbDataPorts, slcAuthTACACSDataPorts.roobsolete OCTET STRING .1.3.6.1.4.1.244.1.1.4.2.1.2 |
slcDevGlobalClearPortsThe Device Ports which remotely authenticated users have permission to clear. This object has been replaced by permissions for each remote authentication method: slcAuthNISClearPorts, slcAuthLDAPClearPorts, slcAuthRADIUSClearPorts, slcAuthKerbClearPorts, slcAuthTACACSClearPorts.roobsolete OCTET STRING .1.3.6.1.4.1.244.1.1.4.2.1.3 |
slcDevGlobalStartTelnetPortThe starting TCP port for Telnet in connections to Device Ports.ro Integer32 .1.3.6.1.4.1.244.1.1.4.2.1.4 |
slcDevGlobalStartSSHPortThe starting TCP port for SSH in connections to Device Ports.ro Integer32 .1.3.6.1.4.1.244.1.1.4.2.1.5 |
slcDevGlobalStartTCPPortThe starting TCP port for TCP in connections to Device Ports.ro Integer32 .1.3.6.1.4.1.244.1.1.4.2.1.6 |
slcDevGlobalMaxDirectThe maximum number of direct connects allowed for each Device Port.roobsolete Integer32 .1.3.6.1.4.1.244.1.1.4.2.1.7 |
slcDevPortConfig OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.4.2.2 |
slcDevPortCfgNumberThe number of entries in the Device Port Configuration table.ro Integer32 ( 8 | 16 | 24 | 32 | 40 | 48 ) .1.3.6.1.4.1.244.1.1.4.2.2.1 |
slcDevPortCfgTableTable for managing Device Port configuration. The number of entries is given by the value of slcDevPortCfgNumber. SEQUENCE OF SlcDevPortCfgEntry .1.3.6.1.4.1.244.1.1.4.2.2.2 |
slcDevPortCfgEntryAn entry containing all configuration settings for a Device Port. SlcDevPortCfgEntry .1.3.6.1.4.1.244.1.1.4.2.2.2.1 |
slcDevPortIdThe identifier for a Device Port.ro Integer32 .1.3.6.1.4.1.244.1.1.4.2.2.2.1.1 |
slcDevPortCfgNameThe name of the Device Port.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.2.2.2.1.2 |
slcDevPortCfgDeviceThe device that is connected to the Device Port. The 'slp*' and 'servertech' values are deprecated and have been replaced by the RPM functionality.ro Enumeration .1.3.6.1.4.1.244.1.1.4.2.2.2.1.3 |
slcDevPortCfgDevLoginThe login used to authenticate to the device connected to the Device Port.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.2.2.2.1.4 |
slcDevPortCfgBreakSeqThe character sequence for the Device Port to send a break.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.2.2.2.1.5 |
slcDevPortCfgTelnetStateIf enabled, Telnet connections to the Device Port are allowed.ro EnabledState .1.3.6.1.4.1.244.1.1.4.2.2.2.1.6 |
slcDevPortCfgTelnetPortTCP Port number for Telnet in connections.ro Integer32 .1.3.6.1.4.1.244.1.1.4.2.2.2.1.7 |
slcDevPortCfgTelnetAuthIf enabled, the user is required to authenticate to access a Device Port with Telnet.ro EnabledState .1.3.6.1.4.1.244.1.1.4.2.2.2.1.8 |
slcDevPortCfgSSHStateIf enabled, SSH connections to the Device Port are allowed.ro EnabledState .1.3.6.1.4.1.244.1.1.4.2.2.2.1.9 |
slcDevPortCfgSSHPortTCP Port number for SSH in connections.ro Integer32 .1.3.6.1.4.1.244.1.1.4.2.2.2.1.10 |
slcDevPortCfgSSHAuthIf enabled, the user is required to authenticate to access a Device Port with SSH.ro EnabledState .1.3.6.1.4.1.244.1.1.4.2.2.2.1.11 |
slcDevPortCfgTCPStateIf enabled, TCP connections to the Device Port are allowed.ro EnabledState .1.3.6.1.4.1.244.1.1.4.2.2.2.1.12 |
slcDevPortCfgTCPPortTCP Port number for TCP in connections.ro Integer32 .1.3.6.1.4.1.244.1.1.4.2.2.2.1.13 |
slcDevPortCfgTCPAuthIf enabled, the user is required to authenticate to access a Device Port with TCP.ro EnabledState .1.3.6.1.4.1.244.1.1.4.2.2.2.1.14 |
slcDevPortCfgIPThe IP Address for Telnet, SSH or TCP in to a Device Port.ro IpAddress .1.3.6.1.4.1.244.1.1.4.2.2.2.1.15 |
slcDevPortCfgBaudThe baud rate of the Device Port.ro Integer32 ( 300 | 600 | 1200 | 2400 | 4800 | 9600 | 19200 | 38400 | 57600 | 115200 ) .1.3.6.1.4.1.244.1.1.4.2.2.2.1.16 |
slcDevPortCfgDataBitsThe data bits of the Device Port.ro Integer32 ( 7 | 8 ) .1.3.6.1.4.1.244.1.1.4.2.2.2.1.17 |
slcDevPortCfgStopBitsThe stop bits of the Device Port.ro Integer32 ( 1 | 2 ) .1.3.6.1.4.1.244.1.1.4.2.2.2.1.18 |
slcDevPortCfgParityThe parity of the Device Port.ro Enumeration .1.3.6.1.4.1.244.1.1.4.2.2.2.1.19 |
slcDevPortCfgFlowControlThe flow control of the Device Port.ro Enumeration .1.3.6.1.4.1.244.1.1.4.2.2.2.1.20 |
slcDevPortCfgLoginsIf enabled, authentication is required to access a serial device connected to a Device Port.ro EnabledState .1.3.6.1.4.1.244.1.1.4.2.2.2.1.21 |
slcDevPortCfgConnectDSRIf enabled, the Device Port only establishes a connection if DSR (Data Set Ready) transitions to an asserted state.ro EnabledState .1.3.6.1.4.1.244.1.1.4.2.2.2.1.22 |
slcDevPortCfgDisconnectDSRIf enabled, and a connection to a Device Port is currently in session, the connection will be terminated if DSR (Data Set Ready) transitions to a de-asserted state.ro EnabledState .1.3.6.1.4.1.244.1.1.4.2.2.2.1.23 |
slcDevPortCfgModemStateFor an external modem attached to the Device Port, indicates how the modem will be used.ro Enumeration .1.3.6.1.4.1.244.1.1.4.2.2.2.1.24 |
slcDevPortCfgModemModeFor an external modem attached to the Device Port, the mode: PPP (for Dial-in and Dial-out) and text (for Dial-in and Dial-back).ro Enumeration .1.3.6.1.4.1.244.1.1.4.2.2.2.1.25 |
slcDevPortCfgLocalIPFor PPP connections, the local IP Address - all zeros if it should be negotiated.ro IpAddress .1.3.6.1.4.1.244.1.1.4.2.2.2.1.26 |
slcDevPortCfgRemoteIPFor PPP connections, the remote IP Address - all zeros if it should be negotiated.ro IpAddress .1.3.6.1.4.1.244.1.1.4.2.2.2.1.27 |
slcDevPortCfgAuthFor PPP connections, the type of authentication to be used.ro Enumeration .1.3.6.1.4.1.244.1.1.4.2.2.2.1.28 |
slcDevPortCfgCHAPHostFor PPP connections with CHAP authentication, the host (for Unix) or user (for Windows) to use.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.2.2.2.1.29 |
slcDevPortCfgInitScriptThe initialization script for an external modem.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.2.2.2.1.30 |
slcDevPortCfgTimeoutThe timeout (in minutes) for text connections. A value of 0 indicates that timeouts are disabled.ro Integer32 .1.3.6.1.4.1.244.1.1.4.2.2.2.1.31 |
slcDevPortCfgDialoutNumThe phone number to use for dial-out connections.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.2.2.2.1.32 |
slcDevPortCfgDialoutLoginThe login to use for dial-out connections.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.2.2.2.1.33 |
slcDevPortCfgDialbackModeFor dial-back connections, defines the phone number to call: a number associated with the authenticated user, or a fixed number associated with the Device Port.ro Enumeration .1.3.6.1.4.1.244.1.1.4.2.2.2.1.34 |
slcDevPortCfgDialbackNumThe phone number to use for dial-back connections.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.2.2.2.1.35 |
slcDevPortCfgNATStateIf enabled, use NAT (Network Address Translation) to allow dial-in and dial-back users to access the network connected to Eth1 and Eth2.ro EnabledState .1.3.6.1.4.1.244.1.1.4.2.2.2.1.36 |
slcDevPortCfgLocalStateIf enabled, local logging is enabled for the Device Port.ro EnabledState .1.3.6.1.4.1.244.1.1.4.2.2.2.1.37 |
slcDevPortCfgNFSFileStateIf enabled, NFS File logging is enabled for the Device Port.ro EnabledState .1.3.6.1.4.1.244.1.1.4.2.2.2.1.38 |
slcDevPortCfgNFSDirThe local directory of a NFS mount to use for logging.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.2.2.2.1.39 |
slcDevPortCfgNFSMaxFilesThe maximum number of files to use for NFS file logging.ro Integer32 .1.3.6.1.4.1.244.1.1.4.2.2.2.1.40 |
slcDevPortCfgNFSMaxSizeThe maximum size of each file (in bytes) for NFS File logging.ro Integer32 UNITS "bytes" .1.3.6.1.4.1.244.1.1.4.2.2.2.1.41 |
slcDevPortCfgEmailStateIf enabled, Token and Data Detection (previously called 'Email Logging') is enabled for the Device Port.ro EnabledState .1.3.6.1.4.1.244.1.1.4.2.2.2.1.42 |
slcDevPortCfgEmailTriggerThe type of trigger to use for Token and Data Detection (previously called 'Email Logging') - number of data bytes received, or token/character string received.ro Enumeration .1.3.6.1.4.1.244.1.1.4.2.2.2.1.43 |
slcDevPortCfgEmailByteThreshWhen Token and Data Detection (previously called 'Email Logging') is configured to trigger on a data byte count, the number of bytes required to trigger an action.ro Integer32 .1.3.6.1.4.1.244.1.1.4.2.2.2.1.44 |
slcDevPortCfgEmailDelayFor Token and Data Detection (previously called 'Email Logging'), a time limit of how long the device port will capture data after the data trigger is detected and before closing the log file and performing the selected actions. This setting is now called 'Action Delay'.ro Integer32 UNITS "seconds" .1.3.6.1.4.1.244.1.1.4.2.2.2.1.45 |
slcDevPortCfgEmailRestartDelayFor Token and Data Detection (previously called 'Email Logging'), the period of time, after performing the selected actions, during which the device port will ignore additional characters received.ro Integer32 UNITS "seconds" .1.3.6.1.4.1.244.1.1.4.2.2.2.1.46 |
slcDevPortCfgEmailTextStringWhen Token and Data Detection (previously called 'Email Logging') is configured to trigger on a character string, this defines the character string that will trigger an action.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.2.2.2.1.47 |
slcDevPortCfgEmailToFor Token and Data Detection (previously called 'Email Logging'), if the Email action is enabled, this object defines the list of emails to send email notification to.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.2.2.2.1.48 |
slcDevPortCfgEmailSubjectFor Token and Data Detection (previously called 'Email Logging'), if the Email action is enabled, this object defines the subject to include with email notification.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.2.2.2.1.49 |
slcDevPortCfgPCCardStateIf enabled, PC Card logging is enabled for the Device Port. This value will be undefined if the SLC does not have PC Card slots.ro EnabledState .1.3.6.1.4.1.244.1.1.4.2.2.2.1.50 |
slcDevPortCfgPCCardLogToFor PC Card logging, which PC Card slot to use for logging. This value will be undefined if the SLC does not have PC Card slots.ro Enumeration .1.3.6.1.4.1.244.1.1.4.2.2.2.1.51 |
slcDevPortCfgPCCardMaxFilesThe maximum number of files to use for PC Card logging. This value will be undefined if the SLC does not have PC Card slots.ro Integer32 .1.3.6.1.4.1.244.1.1.4.2.2.2.1.52 |
slcDevPortCfgPCCardMaxSizeThe maximum size of each file (in bytes) for PC Card logging. This value will be undefined if the SLC does not have PC Card slots.ro Integer32 .1.3.6.1.4.1.244.1.1.4.2.2.2.1.53 |
slcDevPortCfgActionPerforms an action on a Device Port. A read of this object always returns the value noAction(1). Setting this object to zeroPortCounters(2) will reset all port counters given in slcDevPortStateTable. Setting this object to clearLocalLog(3) will clear the local logging buffer. Setting this object to terminateConnections(4) will terminate all connections associated with the Device Port.rw Enumeration .1.3.6.1.4.1.244.1.1.4.2.2.2.1.54 |
slcDevPortCfgEmailSendWhen a trigger is received, the type of notification to send: email, SNMP trap, or email and SNMP trap. This object is deprecated; instead refer to slcDevPortCfgTokenAction.ro Enumeration .1.3.6.1.4.1.244.1.1.4.2.2.2.1.55 |
slcDevPortCfgBannerThe banner displayed when the Device Port is connected to via SSH or Telnet.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.2.2.2.1.56 |
slcDevPortCfgIdleTimeoutThe timeout (in seconds) for dial-in and dial-on-demand PPP connections. If no traffic is received for the PPP connection in the time defined by the idle timeout, the PPP connection will be terminated. A value of 0 indicates that timeouts are disabled.ro Integer32 UNITS "seconds" .1.3.6.1.4.1.244.1.1.4.2.2.2.1.57 |
slcDevPortCfgRestartDelayThe delay (in seconds) to wait before restarting dial-out or dial-on-demand PPP connections.ro Integer32 UNITS "seconds" .1.3.6.1.4.1.244.1.1.4.2.2.2.1.58 |
slcDevPortCfgCallerIdLoggingIf enabled, caller id logging is enabled for a modem dial-in connection.ro EnabledState .1.3.6.1.4.1.244.1.1.4.2.2.2.1.59 |
slcDevPortCfgCallerIdATCmdThe modem AT command required to initiate caller id logging by the modem.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.2.2.2.1.60 |
slcDevPortCfgDODAuthFor PPP connections that are configured for both Dial-in and Dial-on-Demand, the type of authentication to be used for Dial-on-Demand.ro Enumeration .1.3.6.1.4.1.244.1.1.4.2.2.2.1.61 |
slcDevPortCfgDODCHAPHostFor PPP connections that are configured for both Dial-in and Dial-on-Demand, with CHAP authentication for Dial-on-Demand, the host (for Unix) or user (for Windows) to use.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.2.2.2.1.62 |
slcDevPortCfgSLMLoggingStateIf enabled, SLM logging is enabled for the Device Port.ro EnabledState .1.3.6.1.4.1.244.1.1.4.2.2.2.1.63 |
slcDevPortCfgSLMNMSThe IP Addresses of up to three SNMP Network Management Stations defined used for SLM Logging. Multiple IP Addresses will be separated by a comma.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.2.2.2.1.64 |
slcDevPortCfgSLMByteThreshThe number of bytes required to trigger SLM logging.ro Integer32 UNITS "bytes" .1.3.6.1.4.1.244.1.1.4.2.2.2.1.65 |
slcDevPortCfgSLMTimeFrameThe time frame for SLM logging, in seconds.ro Integer32 UNITS "seconds" .1.3.6.1.4.1.244.1.1.4.2.2.2.1.66 |
slcDevPortCfgWebColumnsThe number of columns in the Web SSH or Telnet window for this Device Port.ro Integer32 .1.3.6.1.4.1.244.1.1.4.2.2.2.1.67 |
slcDevPortCfgWebRowsThe number of rows in the Web SSH or Telnet window for this Device Port.ro Integer32 .1.3.6.1.4.1.244.1.1.4.2.2.2.1.68 |
slcDevPortCfgSyslogStateIf enabled, Syslog logging is enabled for the Device Port.ro EnabledState .1.3.6.1.4.1.244.1.1.4.2.2.2.1.69 |
slcDevPortCfgHostListWhen slcDevPortCfgModemState is set to dialinHostList, the name of the Host List used for Dial-in.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.2.2.2.1.70 |
slcDevPortCfgDevLowTempThe low temperature limit, in Celsius, for the device connected to this Device Port. If the temperature is not applicable, 9999 will be returned.ro Integer32 UNITS "Celsius" .1.3.6.1.4.1.244.1.1.4.2.2.2.1.71 |
slcDevPortCfgDevHighTempThe high temperature limit, in Celsius, for the device connected to this Device Port. If the temperature is not applicable, 9999 will be returned.ro Integer32 UNITS "Celsius" .1.3.6.1.4.1.244.1.1.4.2.2.2.1.72 |
slcDevPortCfgDevTemperatureThe actual temperature, in Celsius, for the device connected to this Device Port. If the temperature is not applicable, an empty string will be returned.ro OCTET STRING UNITS "Celsius" .1.3.6.1.4.1.244.1.1.4.2.2.2.1.73 |
slcDevPortCfgDevLowHumidityThe low humidty limit, in percentage, for the device connected to this Device Port. If the temperature is not applicable, 9999 will be returned.ro Integer32 .1.3.6.1.4.1.244.1.1.4.2.2.2.1.74 |
slcDevPortCfgDevHighHumidityThe high humidty limit, in percentage, for the device connected to this Device Port. If the temperature is not applicable, 9999 will be returned.ro Integer32 .1.3.6.1.4.1.244.1.1.4.2.2.2.1.75 |
slcDevPortCfgDevHumidityThe actual humidity, in percentage, for the device connected to this Device Port. If the temperature is not applicable, an empty string will be returned.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.2.2.2.1.76 |
slcDevPortCfgDevTrapsIf enabled, traps will be sent when one of the limits for the device connected to this Device Port are exceeded.ro EnabledState .1.3.6.1.4.1.244.1.1.4.2.2.2.1.77 |
slcDevPortCfgShowLinesIf enabled, upon connecting to the Device Port, a series of characters (or lines) output to the Device Port before it was connected to are displayed.ro EnabledState .1.3.6.1.4.1.244.1.1.4.2.2.2.1.78 |
slcDevPortCfgNumberShowLinesIf slcDevPortCfgShowLines is enabled, the number of lines that are displayed upon connecting to the Device Port.ro Integer32 .1.3.6.1.4.1.244.1.1.4.2.2.2.1.79 |
slcDevPortCfgViewPortLogIf enabled, upon using 'connect direct' to a Device Port, the slcDevPortCfgPortLogSeq key sequence can be typed to view the end of the port log for the current Device Port, or a different Device Port.ro EnabledState .1.3.6.1.4.1.244.1.1.4.2.2.2.1.80 |
slcDevPortCfgPortLogSeqThe character sequence to view the port log for the Device Port.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.2.2.2.1.81 |
slcDevPortCfgMaxDirectConnectsThe maximum number of direct connects at the CLI for the Device Port.ro Integer32 .1.3.6.1.4.1.244.1.1.4.2.2.2.1.82 |
slcDevPortCfgTelnetTimeoutThe timeout (in seconds) for Telnet connections. A value of 0 indicates that timeouts are disabled.ro Integer32 .1.3.6.1.4.1.244.1.1.4.2.2.2.1.83 |
slcDevPortCfgSSHTimeoutThe timeout (in seconds) for SSH connections. A value of 0 indicates that timeouts are disabled.ro Integer32 .1.3.6.1.4.1.244.1.1.4.2.2.2.1.84 |
slcDevPortCfgTCPTimeoutThe timeout (in seconds) for TCP connections. A value of 0 indicates that timeouts are disabled.ro Integer32 .1.3.6.1.4.1.244.1.1.4.2.2.2.1.85 |
slcDevPortCfgCBCPClientTypeWhen slcDevPortCfgModemState is set to cbcpClient, the preferred type of dialback number to use for CBCP negotiation.ro Enumeration .1.3.6.1.4.1.244.1.1.4.2.2.2.1.86 |
slcDevPortCfgCBCPServerAllowNoCallbackIf enabled and slcDevPortCfgModemState is set to cbcpServer, the SLC will allow the PPP peer to select the No Callback option during CBCP negotiation.ro EnabledState .1.3.6.1.4.1.244.1.1.4.2.2.2.1.87 |
slcDevPortCfgDialbackDelayWhen slcDevPortCfgModemState is set to dialback or cbcpServer, specifies the delay between the dial-in and dial-out portion of the dialing sequence.ro Integer32 UNITS "seconds" .1.3.6.1.4.1.244.1.1.4.2.2.2.1.88 |
slcDevPortCfgUSBStateIf enabled, USB logging is enabled for the Device Port. This value will be undefined if the SLC does not have USB Ports.ro EnabledState .1.3.6.1.4.1.244.1.1.4.2.2.2.1.89 |
slcDevPortCfgUSBLogToFor USB logging, which USB port to use for logging. This value will be undefined if the SLC does not have USB Ports.ro Integer32 .1.3.6.1.4.1.244.1.1.4.2.2.2.1.90 |
slcDevPortCfgUSBMaxFilesThe maximum number of files to use for USB logging. This value will be undefined if the SLC does not have USB Ports.ro Integer32 .1.3.6.1.4.1.244.1.1.4.2.2.2.1.91 |
slcDevPortCfgUSBMaxSizeThe maximum size of each file (in bytes) for USB logging. This value will be undefined if the SLC does not have USB Ports.ro Integer32 UNITS "bytes" .1.3.6.1.4.1.244.1.1.4.2.2.2.1.92 |
slcDevPortCfgCHAPAuthLocalUsersIf enabled, the local user list (login and password) is used to validate the CHAP host and secret sent by a remote PPP peer for CHAP authentication, instead of using the CHAP host and secret associated with a modem.ro EnabledState .1.3.6.1.4.1.244.1.1.4.2.2.2.1.93 |
slcDevPortCfgUseSitesIf enabled, sites (a set of site-oriented modem parameters that can be activated by various modem-related events such as authentication, outbound traffic for Dial-on-demand connections, etc.) will be used instead of the parameters configured for the modem.ro EnabledState .1.3.6.1.4.1.244.1.1.4.2.2.2.1.94 |
slcDevPortCfgDialbackRetriesWhen slcDevPortCfgModemState is set to dialback or cbcpServer, specifies the number of times the SLC will retry the dial-out portion of the dialing sequence if the first attempt to dial-out fails.ro Integer32 .1.3.6.1.4.1.244.1.1.4.2.2.2.1.95 |
slcDevPortCfgGroupThe group or groups that may access the Device Port.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.2.2.2.1.96 |
slcDevPortCfgIPMaskThe network mask associated with slcDevPortCfgIPMask.ro IpAddress .1.3.6.1.4.1.244.1.1.4.2.2.2.1.97 |
slcDevPortCfgDevPromptIf the device port is connected to a SLP or ServerTech CDU, specifies the prompt that is configured for the SLP or ServerTech CDU. This object is deprecated, and has been replaced by the RPM functionality.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.2.2.2.1.98 |
slcDevPortCfgDevNumOutletsIf the device port is connected to a ServerTech CDU, specifies the number of outlets on the primary/master ServerTech unit. This object is deprecated, and has been replaced by the RPM functionality.ro Integer32 .1.3.6.1.4.1.244.1.1.4.2.2.2.1.99 |
slcDevPortCfgDevNumExpOutletsIf the device port is connected to a ServerTech CDU, specifies the number of outlets on the expansion ServerTech unit. This object is deprecated, and has been replaced by the RPM functionality.ro Integer32 .1.3.6.1.4.1.244.1.1.4.2.2.2.1.100 |
slcDevPortCfgReversePinoutIf enabled, swaps the positions of the serial lines, such that the direction of data or the signal is reversed. For instance, TX is swapped with RX. Enabling Reverse Pinout facilitates connections to Cisco and Sun style RS-45 console ports using a straight through Ethernet patch cable, without the need for a rolled cable or adapter. Note that all Lantronix serial adapters are intended to be used with Reverse Pinout disabled.ro EnabledState .1.3.6.1.4.1.244.1.1.4.2.2.2.1.101 |
slcDevPortCfgUSBVBUSFor SLC8000 USB Device Ports only. If enabled, the USB VBUS signal provides power to the USB device attached to a device port. Disabling VBUS will power down the device as long as it is bus-powered instead of self-powered.ro EnabledState .1.3.6.1.4.1.244.1.1.4.2.2.2.1.102 |
slcDevPortCfgAssertDTRFor RJ45 Device Ports only. By default, DTR is asserted on a device port nearly all of the time (except momentarily when a port is opened for operations). Unchecking this option will deassert DTR, simulating a cable disconnection for the device that is connected to a device port.ro EnabledState .1.3.6.1.4.1.244.1.1.4.2.2.2.1.103 |
slcDevPortCfgPortTypeIndicates the connector type on the device port: RJ45 or USB.ro Enumeration .1.3.6.1.4.1.244.1.1.4.2.2.2.1.104 |
slcDevPortCfgTelnetTimeoutDataDirectionIf slcDevPortCfgTelnetTimeout is enabled, this setting indicates the direction of data used to determine if the connection has timed out.ro TimeoutDataDirection .1.3.6.1.4.1.244.1.1.4.2.2.2.1.105 |
slcDevPortCfgSSHTimeoutDataDirectionIf slcDevPortCfgSSHTimeout is enabled, this setting indicates the direction of data used to determine if the connection has timed out.ro TimeoutDataDirection .1.3.6.1.4.1.244.1.1.4.2.2.2.1.106 |
slcDevPortCfgTCPTimeoutDataDirectionIf slcDevPortCfgTCPTimeout is enabled, this setting indicates the direction of data used to determine if the connection has timed out.ro TimeoutDataDirection .1.3.6.1.4.1.244.1.1.4.2.2.2.1.107 |
slcDevPortCfgIdleTimeoutMessageIf enabled, a message will be displayed to a user when their connection to a device port will be terminated soon due to the connection being idle.ro EnabledState .1.3.6.1.4.1.244.1.1.4.2.2.2.1.108 |
slcDevPortCfgNumberOfSessionsMessageIf enabled, a message will be displayed to a user when connecting to a device port that indicates how many users are currently connected to the device port.ro EnabledState .1.3.6.1.4.1.244.1.1.4.2.2.2.1.109 |
slcDevPortCfgMinimizeLatencyIf enabled, device port latency will be minimized by reducing read delays.ro EnabledState .1.3.6.1.4.1.244.1.1.4.2.2.2.1.110 |
slcDevPortCfgTelnetSoftIACIf enabled, the Telnet server will not block waiting for the initial Telnet protocol IAC option responses.ro EnabledState .1.3.6.1.4.1.244.1.1.4.2.2.2.1.111 |
slcDevPortCfgSendTermStringIf enabled, and a slcDevPortCfgTerminationString is defined, when a network connection to a device port is terminated, the termination string is sent to the device connected to the device port. The string should be defined so that it sends the the appropriate command(s) to the device to terminate any active user sessions.ro EnabledState .1.3.6.1.4.1.244.1.1.4.2.2.2.1.112 |
slcDevPortCfgTerminationStringThe termination string sent to the device connected to the device port if slcDevPortCfgSendTermString is enabled.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.2.2.2.1.113 |
slcDevPortCfgPowerManagementSeqThe key sequence that displays the Power Management menu when a user is connected to a device port.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.2.2.2.1.114 |
slcDevPortCfgPowerSuppliesA string that describes the managed power supplies configured for the device port. A device port can have up to four power supplies that provide power for the device connected to the device port. The string is a comma separated list of power supplies formatted: '<Power Suppy Name>(RPM Id/Outlet Id)'.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.2.2.2.1.115 |
slcDevPortCfgToggleDTRApplies to RJ45 device ports only. If enabled, when a user disconnects from a device port, DTR will be toggled. This feature can be used when a serial connection requires DSR to be active for the attached device to connect. In this case, toggling DTR will end any active connection on the device.ro EnabledState .1.3.6.1.4.1.244.1.1.4.2.2.2.1.116 |
slcDevPortCfgTokenActionFor Token and Data Detection, a string containing one or more actions that will be performed if a data trigger occurs: syslog, email, trap, sendstring, powersupply.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.2.2.2.1.117 |
slcDevPortCfgTokenSendStringFor Token and Data Detection (previously called 'Email Logging'), if the Send String action is enabled, this object defines the string to send to the device connected to the device port.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.2.2.2.1.118 |
slcDevPortCfgTokenPowerSupplyFor Token and Data Detection (previously called 'Email Logging'), if the Control Power Supply action is enabled, this object defines the name of the managed power supply to perform an action on. This string can be 'all' for all managed power supplies associated with the device port, or an individual power supply name.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.2.2.2.1.119 |
slcDevPortCfgTokenPowerActionFor Token and Data Detection (previously called 'Email Logging'), if the Control Power Supply action is enabled, this object defines the action to take on slcDevPortCfgTokenPowerSupply.ro Enumeration .1.3.6.1.4.1.244.1.1.4.2.2.2.1.120 |
slcDevPortState OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.4.2.3 |
slcDevPortStateNumberThe number of entries in the Device Port State table.ro Integer32 ( 8 | 16 | 24 | 32 | 40 | 48 ) .1.3.6.1.4.1.244.1.1.4.2.3.1 |
slcDevPortStateTableTable of Device Port state entries. The number of entries is given by the value of slcDevPortStateNumber. SEQUENCE OF SlcDevPortStateEntry .1.3.6.1.4.1.244.1.1.4.2.3.2 |
slcDevPortStateEntryAn entry containing all state information for a Device Port. SlcDevPortStateEntry .1.3.6.1.4.1.244.1.1.4.2.3.2.1 |
slcDevPortStateIndexReference index for each Device Port State entry.ro Integer32 .1.3.6.1.4.1.244.1.1.4.2.3.2.1.1 |
slcDevPortStateBytesInputThe number of bytes input to the Device Port since boot or the last time Device Port statistics were zeroed.ro Integer32 UNITS "bytes" .1.3.6.1.4.1.244.1.1.4.2.3.2.1.2 |
slcDevPortStateBytesOutputThe number of bytes output from the Device Port since boot or the last time Device Port statistics were zeroed.ro Integer32 UNITS "bytes" .1.3.6.1.4.1.244.1.1.4.2.3.2.1.3 |
slcDevPortStateFramingErrorsThe number of framing errors for the Device Port since boot or the last time Device Port statistics were zeroed.ro Integer32 .1.3.6.1.4.1.244.1.1.4.2.3.2.1.4 |
slcDevPortStateParityErrorsThe number of parity errors for the Device Port since boot or the last time Device Port statistics were zeroed.ro Integer32 .1.3.6.1.4.1.244.1.1.4.2.3.2.1.5 |
slcDevPortStateOverrunErrorsThe number of overrun errors for the Device Port since boot or the last time Device Port statistics were zeroed.ro Integer32 .1.3.6.1.4.1.244.1.1.4.2.3.2.1.6 |
slcDevPortStateFlowControlViolationsThe number of flow control violations for the Device Port since boot or the last time Device Port statistics were zeroed.ro Integer32 .1.3.6.1.4.1.244.1.1.4.2.3.2.1.7 |
slcDevPortStateDSRIf enabled, Data Set Ready is enabled for the Device Port.ro EnabledState .1.3.6.1.4.1.244.1.1.4.2.3.2.1.8 |
slcDevPortStateDTRIf enabled, Data Terminal Ready is enabled for the Device Port.ro EnabledState .1.3.6.1.4.1.244.1.1.4.2.3.2.1.9 |
slcDevPortStateCTSIf enabled, Clear To Send is enabled for the Device Port.ro EnabledState .1.3.6.1.4.1.244.1.1.4.2.3.2.1.10 |
slcDevPortStateRTSIf enabled, Request To Send is enabled for the Device Port.ro EnabledState .1.3.6.1.4.1.244.1.1.4.2.3.2.1.11 |
slcDevPortStateCDIf enabled, Carrier Detect is enabled for the Device Port.ro EnabledState .1.3.6.1.4.1.244.1.1.4.2.3.2.1.12 |
slcDevPCCard OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.4.3 |
slcPCCardCfgTableTable of PC Card configuration entries. There are two entries in the table, index (1) for the upper PC Card slot, and index (2) for the lower PC Card slot. This table will be empty if the SLC does not have PC Card slots. SEQUENCE OF SlcPCCardCfgEntry .1.3.6.1.4.1.244.1.1.4.3.1 |
slcPCCardCfgEntryAn entry containing all configuration settings for a PC Card Slot. SlcPCCardCfgEntry .1.3.6.1.4.1.244.1.1.4.3.1.1 |
slcPCCardCfgIndexReference index for each PC Card Configuration entry.ro Integer32 .1.3.6.1.4.1.244.1.1.4.3.1.1.1 |
slcPCCardCfgCardTypeThe type of PC Card in the slot.ro Enumeration .1.3.6.1.4.1.244.1.1.4.3.1.1.2 |
slcPCCardCfgCardIdThe identifying string of the card in the slot.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.3.1.1.3 |
slcPCCardCfgBaudFor ISDN and modem cards, the baud rate.ro Integer32 ( 300 | 600 | 1200 | 2400 | 4800 | 9600 | 19200 | 38400 | 57600 | 115200 ) .1.3.6.1.4.1.244.1.1.4.3.1.1.4 |
slcPCCardCfgDataBitsFor ISDN and modem cards, the data bits.ro Integer32 ( 7 | 8 ) .1.3.6.1.4.1.244.1.1.4.3.1.1.5 |
slcPCCardCfgStopBitsFor ISDN and modem cards, the stop bits.ro Integer32 ( 1 | 2 ) .1.3.6.1.4.1.244.1.1.4.3.1.1.6 |
slcPCCardCfgParityFor ISDN and modem cards, the parity.ro Enumeration .1.3.6.1.4.1.244.1.1.4.3.1.1.7 |
slcPCCardCfgFlowControlFor ISDN and modem cards, the flow control.ro Enumeration .1.3.6.1.4.1.244.1.1.4.3.1.1.8 |
slcPCCardCfgModemStateFor ISDN and modem cards, indicates how the modem will be used.ro Enumeration .1.3.6.1.4.1.244.1.1.4.3.1.1.9 |
slcPCCardCfgModemModeFor ISDN and modem cards, the mode: PPP (for Dial-in and Dial-out) and text (for Dial-in and Dial-back).ro Enumeration .1.3.6.1.4.1.244.1.1.4.3.1.1.10 |
slcPCCardCfgLocalIPFor PPP connections, the local IP Address (all zeros if it should be negotiated).ro IpAddress .1.3.6.1.4.1.244.1.1.4.3.1.1.11 |
slcPCCardCfgRemoteIPFor PPP connections, the remote IP Address (all zeros if it should be negotiated).ro IpAddress .1.3.6.1.4.1.244.1.1.4.3.1.1.12 |
slcPCCardCfgAuthFor PPP connections, the type of authentication to be used.ro Enumeration .1.3.6.1.4.1.244.1.1.4.3.1.1.13 |
slcPCCardCfgCHAPHostFor PPP connections with CHAP authentication, the host (for Unix) or user (for Windows) to use.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.3.1.1.14 |
slcPCCardCfgInitScriptThe initialization script for an external modem.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.3.1.1.15 |
slcPCCardCfgTimeoutThe timeout (in minutes) for text connections. A value of 0 indicates that timeouts are disabled.ro Integer32 .1.3.6.1.4.1.244.1.1.4.3.1.1.16 |
slcPCCardCfgDialoutNumThe phone number to use for dial-out connections.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.3.1.1.17 |
slcPCCardCfgDialoutLoginThe login to use for dial-out connections.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.3.1.1.18 |
slcPCCardCfgDialbackModeFor dial-back connections, defines the phone number to call: a number associated with the authenticated user, or a fixed number associated with the Device Port.ro Enumeration .1.3.6.1.4.1.244.1.1.4.3.1.1.19 |
slcPCCardCfgDialbackNumThe phone number to use for dial-back connections.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.3.1.1.20 |
slcPCCardCfgNATStateIf enabled, use NAT (Network Address Translation) to allow dial-in and dial-back users to access the network connected to Eth1 and Eth2.ro EnabledState .1.3.6.1.4.1.244.1.1.4.3.1.1.21 |
slcPCCardCfgStorageFSFor storage cards, the type of filesystem on the card.ro Enumeration .1.3.6.1.4.1.244.1.1.4.3.1.1.22 |
slcPCCardCfgISDNChannelThe channel on the ISDN card to use, either 1 or 2.ro Integer32 .1.3.6.1.4.1.244.1.1.4.3.1.1.23 |
slcPCCardCfgISDNChannelNumThe phone number associated with the selected ISDN channel.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.3.1.1.24 |
slcPCCardCfgTelnetStateIf enabled, Telnet connections to the modem/ISDN PC Card are allowed.ro EnabledState .1.3.6.1.4.1.244.1.1.4.3.1.1.25 |
slcPCCardCfgTelnetPortTCP Port number for Telnet connections directly to the modem/ISDN PC Card.ro Integer32 .1.3.6.1.4.1.244.1.1.4.3.1.1.26 |
slcPCCardCfgTelnetAuthIf enabled, the user is required to authenticate to access the modem/ISDN PC Card with Telnet.ro EnabledState .1.3.6.1.4.1.244.1.1.4.3.1.1.27 |
slcPCCardCfgSSHStateIf enabled, SSH connections to the modem/ISDN PC Card are allowed.ro EnabledState .1.3.6.1.4.1.244.1.1.4.3.1.1.28 |
slcPCCardCfgSSHPortTCP Port number for SSH connections directly to the modem/ISDN PC Card.ro Integer32 .1.3.6.1.4.1.244.1.1.4.3.1.1.29 |
slcPCCardCfgSSHAuthIf enabled, the user is required to authenticate to access the modem/ISDN PC Card with SSH.ro EnabledState .1.3.6.1.4.1.244.1.1.4.3.1.1.30 |
slcPCCardCfgTCPStateIf enabled, TCP connections to the modem/ISDN PC Card are allowed.ro EnabledState .1.3.6.1.4.1.244.1.1.4.3.1.1.31 |
slcPCCardCfgTCPPortTCP Port number for TCP connections directly to the modem/ISDN PC Card.ro Integer32 .1.3.6.1.4.1.244.1.1.4.3.1.1.32 |
slcPCCardCfgTCPAuthIf enabled, the user is required to authenticate to access the modem/ISDN PC Card with TCP.ro EnabledState .1.3.6.1.4.1.244.1.1.4.3.1.1.33 |
slcPCCardCfgGSMPINThe PIN associated with the GSM/GPRS PC Card modem.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.3.1.1.34 |
slcPCCardCfgGSMNetworkNameThe Network Name associated with the GSM/GPRS PC Card modem.roobsolete OCTET STRING .1.3.6.1.4.1.244.1.1.4.3.1.1.35 |
slcPCCardCfgGSMPPPCompressionIf enabled, PPP compression is enabled for GSM/GPRS PC Card modem connections.ro EnabledState .1.3.6.1.4.1.244.1.1.4.3.1.1.36 |
slcPCCardCfgGSMAutoAcquireDNSIf enabled, DNS servers will be acquired vi GSM/GPRS PC Card modem PPP connections.ro EnabledState .1.3.6.1.4.1.244.1.1.4.3.1.1.37 |
slcPCCardCfgGSMDialoutModeThe mode to be used for GSM/GPRS PC Card modems configured for dialout.ro Enumeration .1.3.6.1.4.1.244.1.1.4.3.1.1.38 |
slcPCCardCfgGSMContextIDThe Context Id string used for GSM/GPRS PC Card modems configured for GPRS dialout mode.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.3.1.1.39 |
slcPCCardCfgGSMBearerServiceThe Bearer Service Type string used for GSM/GPRS PC Card modems configured for GSM dialin/dialout mode.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.3.1.1.40 |
slcPCCardCfgIdleTimeoutThe timeout (in seconds) for dial-in and dial-on-demand PPP connections. If no traffic is received for the PPP connection in the time defined by the idle timeout, the PPP connection will be terminated. A value of 0 indicates that timeouts are disabled.ro Integer32 .1.3.6.1.4.1.244.1.1.4.3.1.1.41 |
slcPCCardCfgRestartDelayThe delay (in seconds) to wait before restarting dial-out or dial-on-demand PPP connections.ro Integer32 UNITS "seconds" .1.3.6.1.4.1.244.1.1.4.3.1.1.42 |
slcPCCardCfgCallerIdLoggingIf enabled, caller id logging is enabled for a modem dial-in connection.ro EnabledState .1.3.6.1.4.1.244.1.1.4.3.1.1.43 |
slcPCCardCfgCallerIdATCmdThe modem AT command required to initiate caller id logging by the modem.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.3.1.1.44 |
slcPCCardCfgDODAuthFor PPP connections that are configured for both Dial-in and Dial-on-Demand, the type of authentication to be used for Dial-on-Demand.ro Enumeration .1.3.6.1.4.1.244.1.1.4.3.1.1.45 |
slcPCCardCfgDODCHAPHostFor PPP connections that are configured for both Dial-in and Dial-on-Demand, with CHAP authentication for Dial-on-Demand, the host (for Unix) or user (for Windows) to use.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.3.1.1.46 |
slcPCCardCfgHostListWhen slcPCCardCfgModemState is set to dialinHostList, the name of the Host List used for Dial-in.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.3.1.1.47 |
slcPCCardCfgCBCPClientTypeWhen slcPCCardCfgModemState is set to cbcpClient, the preferred type of dialback number to use for CBCP negotiation.ro Enumeration .1.3.6.1.4.1.244.1.1.4.3.1.1.48 |
slcPCCardCfgCBCPServerAllowNoCallbackIf enabled and slcPCCardCfgModemState is set to cbcpServer, the SLC will allow the PPP peer to select the No Callback option during CBCP negotiation.ro EnabledState .1.3.6.1.4.1.244.1.1.4.3.1.1.49 |
slcPCCardCfgDialbackDelayWhen slcPCCardCfgModemState is set to dialback or cbcpServer, specifies the delay between the dial-in and dial-out portion of the dialing sequence.ro Integer32 UNITS "seconds" .1.3.6.1.4.1.244.1.1.4.3.1.1.50 |
slcPCCardCfgCHAPAuthLocalUsersIf enabled, the local user list (login and password) is used to validate the CHAP host and secret sent by a remote PPP peer for CHAP authentication, instead of using the CHAP host and secret associated with a modem.ro EnabledState .1.3.6.1.4.1.244.1.1.4.3.1.1.51 |
slcPCCardCfgUseSitesIf enabled, sites (a set of site-oriented modem parameters that can be activated by various modem-related events such as authentication, outbound traffic for Dial-on-demand connections, etc.) will be used instead of the parameters configured for the modem.ro EnabledState .1.3.6.1.4.1.244.1.1.4.3.1.1.52 |
slcPCCardCfgDialbackRetriesWhen slcPCCardCfgModemState is set to dialback or cbcpServer, specifies the number of times the SLC will retry the dial-out portion of the dialing sequence if the first attempt to dial-out fails.ro Integer32 .1.3.6.1.4.1.244.1.1.4.3.1.1.53 |
slcPCCardCfgGroupThe group or groups that may access the PC Card slot.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.3.1.1.54 |
slcDevPowerSupply OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.4.4 |
slcDevPowerSupplyTypeThe type of power supply for the SLC.ro Enumeration .1.3.6.1.4.1.244.1.1.4.4.1 |
slcDevPowerSupplyAThe status of Power Supply A.ro Enumeration .1.3.6.1.4.1.244.1.1.4.4.2 |
slcDevPowerSupplyBThe status of Power Supply B.ro Enumeration .1.3.6.1.4.1.244.1.1.4.4.3 |
slcDevUSB OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.4.5 |
slcDevUSBStateIf enabled, the USB devices connected to the SLC will be accessible. This value will be undefined if the SLC does not have USB Ports.ro EnabledState .1.3.6.1.4.1.244.1.1.4.5.1 |
slcDevUSBCfgTableTable of USB configuration entries. There is one entry in the table, index (1) for USB port 1. This table will be empty if the SLC does not have USB Ports. SEQUENCE OF SlcDevUSBCfgEntry .1.3.6.1.4.1.244.1.1.4.5.2 |
slcDevUSBCfgEntryAn entry containing all configuration settings for a USB port. SlcDevUSBCfgEntry .1.3.6.1.4.1.244.1.1.4.5.2.1 |
slcDevUSBIdThe identifier for a USB Port (1 indicates USB Port U1).ro Integer32 (1) .1.3.6.1.4.1.244.1.1.4.5.2.1.1 |
slcDevUSBCfgCardTypeThe type of USB device in the port.ro Enumeration .1.3.6.1.4.1.244.1.1.4.5.2.1.2 |
slcDevUSBCfgCardIdThe identifying string of the device in the port.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.5.2.1.3 |
slcDevUSBCfgStorageFSFor thumb drives, the type of filesystem on the card.ro Enumeration .1.3.6.1.4.1.244.1.1.4.5.2.1.4 |
slcDevUSBCfgBaudFor modem cards, the baud rate.ro Integer32 ( 300 | 600 | 1200 | 2400 | 4800 | 9600 | 19200 | 38400 | 57600 | 115200 ) .1.3.6.1.4.1.244.1.1.4.5.2.1.5 |
slcDevUSBCfgDataBitsFor modem cards, the data bits.ro Integer32 ( 7 | 8 ) .1.3.6.1.4.1.244.1.1.4.5.2.1.6 |
slcDevUSBCfgStopBitsFor modem cards, the stop bits.ro Integer32 ( 1 | 2 ) .1.3.6.1.4.1.244.1.1.4.5.2.1.7 |
slcDevUSBCfgParityFor modem cards, the parity.ro Enumeration .1.3.6.1.4.1.244.1.1.4.5.2.1.8 |
slcDevUSBCfgFlowControlFor modem cards, the flow control.ro Enumeration .1.3.6.1.4.1.244.1.1.4.5.2.1.9 |
slcDevUSBCfgModemStateFor modem cards, indicates how the modem will be used.ro Enumeration .1.3.6.1.4.1.244.1.1.4.5.2.1.10 |
slcDevUSBCfgModemModeFor modem cards, the mode: PPP (for Dial-in and Dial-out) and text (for Dial-in and Dial-back).ro Enumeration .1.3.6.1.4.1.244.1.1.4.5.2.1.11 |
slcDevUSBCfgLocalIPFor PPP connections, the local IP Address (all zeros if it should be negotiated).ro IpAddress .1.3.6.1.4.1.244.1.1.4.5.2.1.12 |
slcDevUSBCfgRemoteIPFor PPP connections, the remote IP Address (all zeros if it should be negotiated).ro IpAddress .1.3.6.1.4.1.244.1.1.4.5.2.1.13 |
slcDevUSBCfgAuthFor PPP connections, the type of authentication to be used.ro Enumeration .1.3.6.1.4.1.244.1.1.4.5.2.1.14 |
slcDevUSBCfgCHAPHostFor PPP connections with CHAP authentication, the host (for Unix) or user (for Windows) to use.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.5.2.1.15 |
slcDevUSBCfgDODAuthFor PPP connections that are configured for both Dial-in and Dial-on-Demand, the type of authentication to be used for Dial-on-Demand.ro Enumeration .1.3.6.1.4.1.244.1.1.4.5.2.1.16 |
slcDevUSBCfgDODCHAPHostFor PPP connections that are configured for both Dial-in and Dial-on-Demand, with CHAP authentication for Dial-on-Demand, the host (for Unix) or user (for Windows) to use.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.5.2.1.17 |
slcDevUSBCfgInitScriptThe initialization script for a modem.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.5.2.1.18 |
slcDevUSBCfgTimeoutThe timeout (in minutes) for text connections. A value of 0 indicates that timeouts are disabled.ro Integer32 .1.3.6.1.4.1.244.1.1.4.5.2.1.19 |
slcDevUSBCfgDialoutNumThe phone number to use for dial-out connections.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.5.2.1.20 |
slcDevUSBCfgDialoutLoginThe login to use for dial-out connections.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.5.2.1.21 |
slcDevUSBCfgDialbackModeFor dial-back connections, defines the phone number to call: a number associated with the authenticated user, or a fixed number associated with the Device Port.ro Enumeration .1.3.6.1.4.1.244.1.1.4.5.2.1.22 |
slcDevUSBCfgDialbackNumThe phone number to use for dial-back connections.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.5.2.1.23 |
slcDevUSBCfgDialbackDelayWhen slcDevUSBCfgModemState is set to dialback or cbcpServer, specifies the delay between the dial-in and dial-out portion of the dialing sequence.ro Integer32 UNITS "seconds" .1.3.6.1.4.1.244.1.1.4.5.2.1.24 |
slcDevUSBCfgNATStateIf enabled, use NAT (Network Address Translation) to allow dial-in and dial-back users to access the network connected to Eth1 and Eth2.ro EnabledState .1.3.6.1.4.1.244.1.1.4.5.2.1.25 |
slcDevUSBCfgIdleTimeoutThe timeout (in seconds) for dial-in and dial-on-demand PPP connections. If no traffic is received for the PPP connection in the time defined by the idle timeout, the PPP connection will be terminated. A value of 0 indicates that timeouts are disabled.ro Integer32 UNITS "seconds" .1.3.6.1.4.1.244.1.1.4.5.2.1.26 |
slcDevUSBCfgRestartDelayThe delay (in seconds) to wait before restarting dial-out or dial-on-demand PPP connections.ro Integer32 UNITS "seconds" .1.3.6.1.4.1.244.1.1.4.5.2.1.27 |
slcDevUSBCfgCallerIdLoggingIf enabled, caller id logging is enabled for a modem dial-in connection.ro EnabledState .1.3.6.1.4.1.244.1.1.4.5.2.1.28 |
slcDevUSBCfgCallerIdATCmdThe modem AT command required to initiate caller id logging by the modem.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.5.2.1.29 |
slcDevUSBCfgHostListWhen slcDevUSBCfgModemState is set to dialinHostList, the name of the Host List used for Dial-in.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.5.2.1.30 |
slcDevUSBCfgCBCPClientTypeWhen slcDevUSBCfgModemState is set to cbcpClient, the preferred type of dialback number to use for CBCP negotiation.ro Enumeration .1.3.6.1.4.1.244.1.1.4.5.2.1.31 |
slcDevUSBCfgCBCPServerAllowNoCallbackIf enabled and slcDevUSBCfgModemState is set to cbcpServer, the SLC will allow the PPP peer to select the No Callback option during CBCP negotiation.ro EnabledState .1.3.6.1.4.1.244.1.1.4.5.2.1.32 |
slcDevUSBCfgTelnetStateIf enabled, Telnet connections to the USB modem are allowed.ro EnabledState .1.3.6.1.4.1.244.1.1.4.5.2.1.33 |
slcDevUSBCfgTelnetPortTCP Port number for Telnet connections directly to the USB modem.ro Integer32 .1.3.6.1.4.1.244.1.1.4.5.2.1.34 |
slcDevUSBCfgTelnetAuthIf enabled, the user is required to authenticate to access the USB modem with Telnet.ro EnabledState .1.3.6.1.4.1.244.1.1.4.5.2.1.35 |
slcDevUSBCfgSSHStateIf enabled, SSH connections to the USB modem are allowed.ro EnabledState .1.3.6.1.4.1.244.1.1.4.5.2.1.36 |
slcDevUSBCfgSSHPortTCP Port number for SSH connections directly to the USB modem.ro Integer32 .1.3.6.1.4.1.244.1.1.4.5.2.1.37 |
slcDevUSBCfgSSHAuthIf enabled, the user is required to authenticate to access the USB modem with SSH.ro EnabledState .1.3.6.1.4.1.244.1.1.4.5.2.1.38 |
slcDevUSBCfgTCPStateIf enabled, TCP connections to the USB modem are allowed.ro EnabledState .1.3.6.1.4.1.244.1.1.4.5.2.1.39 |
slcDevUSBCfgTCPPortTCP Port number for TCP connections directly to the USB modem.ro Integer32 .1.3.6.1.4.1.244.1.1.4.5.2.1.40 |
slcDevUSBCfgTCPAuthIf enabled, the user is required to authenticate to access the USB modem with TCP.ro EnabledState .1.3.6.1.4.1.244.1.1.4.5.2.1.41 |
slcDevUSBCfgGSMPINThe PIN associated with the GSM/GPRS modem.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.5.2.1.42 |
slcDevUSBCfgGSMPPPCompressionIf enabled, PPP compression is enabled GSM/GPRS modem connections.ro EnabledState .1.3.6.1.4.1.244.1.1.4.5.2.1.43 |
slcDevUSBCfgGSMAutoAcquireDNSIf enabled, DNS servers will be acquired vi GSM/GPRS modem PPP connections.ro EnabledState .1.3.6.1.4.1.244.1.1.4.5.2.1.44 |
slcDevUSBCfgGSMDialoutModeThe mode to be used for GSM/GPRS modems configured for dialout.ro Enumeration .1.3.6.1.4.1.244.1.1.4.5.2.1.45 |
slcDevUSBCfgGSMContextIDThe Context Id string used for GSM/GPRS modems configured for GPRS dialout mode.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.5.2.1.46 |
slcDevUSBCfgGSMBearerServiceThe Bearer Service Type string used for GSM/GPRS modems configured for GSM dialin/dialout mode.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.5.2.1.47 |
slcDevUSBCfgCHAPAuthLocalUsersIf enabled, the local user list (login and password) is used to validate the CHAP host and secret sent by a remote PPP peer for CHAP authentication, instead of using the CHAP host and secret associated with a modem.ro EnabledState .1.3.6.1.4.1.244.1.1.4.5.2.1.48 |
slcDevUSBCfgUseSitesIf enabled, sites (a set of site-oriented modem parameters that can be activated by various modem-related events such as authentication, outbound traffic for Dial-on-demand connections, etc.) will be used instead of the parameters configured for the modem.ro EnabledState .1.3.6.1.4.1.244.1.1.4.5.2.1.49 |
slcDevUSBCfgDialbackRetriesWhen slcDevUSBCfgModemState is set to dialback or cbcpServer, specifies the number of times the SLC will retry the dial-out portion of the dialing sequence if the first attempt to dial-out fails.ro Integer32 .1.3.6.1.4.1.244.1.1.4.5.2.1.50 |
slcDevUSBCfgDialtoneCheckThe time (in minutes) between checks for a modem dialtone. A value of 0 indicates that dialtone checks are disabled.ro Integer32 .1.3.6.1.4.1.244.1.1.4.5.2.1.51 |
slcDevUSBCfgGroupThe group or groups that may access the USB port.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.5.2.1.52 |
slcDevIntModem OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.4.6 |
slcDevIntModemModemStateFor the SLC internal modem, indicates how the modem will be used.ro Enumeration .1.3.6.1.4.1.244.1.1.4.6.1 |
slcDevIntModemModemModeFor the SLC internal modem, the mode: PPP (for Dial-in and Dial-out) and text (for Dial-in and Dial-back).ro Enumeration .1.3.6.1.4.1.244.1.1.4.6.2 |
slcDevIntModemLocalIPFor PPP connections, the local IP Address - all zeros if it should be negotiated.ro IpAddress .1.3.6.1.4.1.244.1.1.4.6.3 |
slcDevIntModemRemoteIPFor PPP connections, the remote IP Address - all zeros if it should be negotiated.ro IpAddress .1.3.6.1.4.1.244.1.1.4.6.4 |
slcDevIntModemAuthFor PPP connections, the type of authentication to be used.ro Enumeration .1.3.6.1.4.1.244.1.1.4.6.5 |
slcDevIntModemCHAPHostFor PPP connections with CHAP authentication, the host (for Unix) or user (for Windows) to use.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.6.6 |
slcDevIntModemInitScriptThe initialization script for an internal modem.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.6.7 |
slcDevIntModemTimeoutThe timeout (in minutes) for text connections. A value of 0 indicates that timeouts are disabled.ro Integer32 .1.3.6.1.4.1.244.1.1.4.6.8 |
slcDevIntModemDialoutNumThe phone number to use for dial-out connections.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.6.9 |
slcDevIntModemDialoutLoginThe login to use for dial-out connections.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.6.10 |
slcDevIntModemDialbackModeFor dial-back connections, defines the phone number to call: a number associated with the authenticated user, or a fixed number associated with the internal modem.ro Enumeration .1.3.6.1.4.1.244.1.1.4.6.11 |
slcDevIntModemDialbackNumThe phone number to use for dial-back connections.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.6.12 |
slcDevIntModemDialbackRetriesWhen slcDevIntModemModemState is set to dialback, specifies the number of times the SLC will retry the dial-out portion of the dialing sequence if the first attempt to dial-out fails.ro Integer32 .1.3.6.1.4.1.244.1.1.4.6.13 |
slcDevIntModemDialbackDelayWhen slcDevIntModemModemState is set to dialback, specifies the delay between the dial-in and dial-out portion of the dialing sequence.ro Integer32 UNITS "seconds" .1.3.6.1.4.1.244.1.1.4.6.14 |
slcDevIntModemCallerIdLoggingIf enabled, caller id logging is enabled for a modem dial-in connection.ro EnabledState .1.3.6.1.4.1.244.1.1.4.6.15 |
slcDevIntModemCallerIdATCmdThe modem AT command required to initiate caller id logging by the modem.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.6.16 |
slcDevIntModemUseSitesIf enabled, sites (a set of site-oriented modem parameters that can be activated by various modem-related events such as authentication, outbound traffic for Dial-on-demand connections, etc.) will be used instead of the parameters configured for the modem.ro EnabledState .1.3.6.1.4.1.244.1.1.4.6.17 |
slcDevIntModemGroupThe group or groups that may access the internal modem connection.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.6.18 |
slcDevIntModemIdleTimeoutThe timeout (in seconds) for dial-in and dial-on-demand PPP connections. If no traffic is received for the PPP connection in the time defined by the idle timeout, the PPP connection will be terminated. A value of 0 indicates that timeouts are disabled.ro Integer32 UNITS "seconds" .1.3.6.1.4.1.244.1.1.4.6.19 |
slcDevIntModemRestartDelayThe delay (in seconds) to wait before restarting dial-out or dial-on-demand PPP connections.ro Integer32 UNITS "seconds" .1.3.6.1.4.1.244.1.1.4.6.20 |
slcDevIntModemNATStateIf enabled, use NAT (Network Address Translation) to allow dial-in and dial-back users to access the network connected to Eth1 and Eth2.ro EnabledState .1.3.6.1.4.1.244.1.1.4.6.21 |
slcDevIntModemDialtoneCheckThe time (in minutes) between checks for a modem dialtone. A value of 0 indicates that dialtone checks are disabled.ro Integer32 .1.3.6.1.4.1.244.1.1.4.6.22 |
slcDevRPM OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.4.7 |
slcDevRPMCfgTableTable of RPM configuration entries. SEQUENCE OF SlcDevRPMCfgEntry .1.3.6.1.4.1.244.1.1.4.7.1 |
slcDevRPMCfgEntryAn entry containing all configuration settings for an RPM, as well as some top level status information for the RPM. SlcDevRPMCfgEntry .1.3.6.1.4.1.244.1.1.4.7.1.1 |
slcDevRPMIdThe unique identifier for an RPM device.ro Integer32 .1.3.6.1.4.1.244.1.1.4.7.1.1.1 |
slcDevRPMNameThe name of the RPM.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.7.1.1.2 |
slcDevRPMVendorModelThe manufacture and model of the RPM.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.7.1.1.3 |
slcDevRPMManagedViaThe method of control for managing the RPM.ro Enumeration .1.3.6.1.4.1.244.1.1.4.7.1.1.4 |
slcDevRPMIPAddressFor SNMP and network managed RPMs, the IP Address of the RPM.ro IpAddress .1.3.6.1.4.1.244.1.1.4.7.1.1.5 |
slcDevRPMPortFor network managed RPMs, the TCP port to use to connect to the RPM. For USB managed RPMs, the USB port the device is connected to (0 indicates a port on the front of the SLC). For serially managed RPMs, the RJ45 device port the device is connected to.ro Integer32 .1.3.6.1.4.1.244.1.1.4.7.1.1.6 |
slcDevRPMDriverOptsAny driver options that are configured for the RPM. This option is mostly used for the USB vendor and product id.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.7.1.1.7 |
slcDevRPMStatusThe current status for the RPM; for example, 'OL' to indicate 'Online' for a UPS. This object may be blank if the device does not report a status, or if the device is not in an error state.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.7.1.1.8 |
slcDevRPMFirmwareVersionThe current firmware version of the RPM. This object may be blank if the device does not report its firmware version.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.7.1.1.9 |
slcDevRPMSerialNumberThe serial number of the RPM. This object may be blank if the device does not report its serial number.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.7.1.1.10 |
slcDevRPMMACAddressThe hardware address of the ethernet port of the RPM. This object may be blank if the device does not report its MAC address.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.7.1.1.11 |
slcDevRPMNumOutletsThe number of power outlets that the RPM has.ro Integer32 .1.3.6.1.4.1.244.1.1.4.7.1.1.12 |
slcDevRPMOutletsOnThe number of RPM outlets that are currently turned on. A negative value indicates that the RPM does not report how many outlets are turned on.ro Integer32 (-1..120) .1.3.6.1.4.1.244.1.1.4.7.1.1.13 |
slcDevRPMSNMPReadCommFor SNMP managed RPMs, the SNMP read (get) community.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.7.1.1.14 |
slcDevRPMAdminLoginFor serial or network managed RPMs, the administrator login.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.7.1.1.15 |
slcDevRPMLogStatusIndicates how frequently the status for the RPM is logged. A value of 0 indicates that logging is disabled.ro Integer32 .1.3.6.1.4.1.244.1.1.4.7.1.1.16 |
slcDevRPMCriticalSNMPTrapsIf enabled, indicates that the slcEventRPMAction trap will be sent for critical events for the RPM.ro EnabledState .1.3.6.1.4.1.244.1.1.4.7.1.1.17 |
slcDevRPMCriticalEmailsAn email address to send emails to for critical events for the RPM.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.7.1.1.18 |
slcDevRPMProvidesSLCPowerIf enabled, indicates that the RPM provides power to the SLC.ro EnabledState .1.3.6.1.4.1.244.1.1.4.7.1.1.19 |
slcDevRPMOnLowBatteryIndicates the action taken when a UPS is on battery and reaches a 'low battery' state. Applies to UPS devices only.ro Enumeration .1.3.6.1.4.1.244.1.1.4.7.1.1.20 |
slcDevRPMShutdownOrderIf a UPS reaches a 'low battery' state and its slcDevRPMOnLowBattery setting is shutdownAllUPS, this indicates the order in which this RPM will be shutdown as all UPSes are shutdown. All UPSes with a shutdown order of '1' will be shutdown first, followed by all UPSes with a shutdown order of '2', etc. Shutdown orders are in the range of 1 to 49, with 50 being reserved for UPSes that provide power to the SLC - they will always be shutdown last. A value of 0 indicates that this UPS will not be shutdown. Applies to UPS devices only.ro Integer32 .1.3.6.1.4.1.244.1.1.4.7.1.1.21 |
slcDevRPMLoadThe current load of the RPM expressed as a percentage. The value is in tenths of a percent. A negative value indicates that the RPM does not report load values.ro Integer32 (-1..1000) UNITS "tenths of a percent" .1.3.6.1.4.1.244.1.1.4.7.1.1.22 |
slcDevRPMLoadOverThresholdThe load when the RPM switches to an overload condition, expressed as a percentage. The value is in tenths of a percent. A negative value indicates that the RPM does not report over load threshold values.ro Integer32 (-1..1000) UNITS "tenths of a percent" .1.3.6.1.4.1.244.1.1.4.7.1.1.23 |
slcDevRPMBatteryChargeThe current battery charge for the the RPM, expressed as a percentage. The value is in tenths of a percent. A negative value indicates that the RPM does not report battery charge values.ro Integer32 (-1..1000) UNITS "tenths of a percent" .1.3.6.1.4.1.244.1.1.4.7.1.1.24 |
slcDevRPMBatteryRuntimeThe number of seconds in the RPM remaining battery life. A value of 0 indicates that the RPM does not report battery runtime values.ro TimeTicks UNITS "hundredths of seconds" .1.3.6.1.4.1.244.1.1.4.7.1.1.25 |
slcDevRPMBeeperStatusIf enabled, indicates that the RPM beeper is enabled. A value of 0 indicates that the RPM does not report beeper status.ro EnabledState .1.3.6.1.4.1.244.1.1.4.7.1.1.26 |
slcDevRPMTemperatureThe internal temperature of the RPM, given in Celsius. A value of less than or equal to zero indicates that the RPM does not report temperature values.ro Integer32 UNITS "Celsius" .1.3.6.1.4.1.244.1.1.4.7.1.1.27 |
slcDevRPMUptimeThe number of seconds the RPM has been up. A value of 0 indicates that the RPM does not report uptime values.ro TimeTicks UNITS "hundredths of seconds" .1.3.6.1.4.1.244.1.1.4.7.1.1.28 |
slcDevRPMStatusTableTable of RPM status entries. SEQUENCE OF SlcDevRPMStatusEntry .1.3.6.1.4.1.244.1.1.4.7.2 |
slcDevRPMStatusEntryAn entry containing status information for an RPM. The SLC supports up to two towers or units per RPM. SlcDevRPMStatusEntry .1.3.6.1.4.1.244.1.1.4.7.2.1 |
slcDevRPMCurrentThe total current level, in tenths of Amps, for all outlets, on a given RPM tower or unit. If the value is negative, the RPM does not report current for the tower or unit.ro Integer32 UNITS "tenths of Amps" .1.3.6.1.4.1.244.1.1.4.7.2.1.1 |
slcDevRPMInputVoltageThe input voltage, in tenths of Volts, on a given RPM tower or unit. If the value is negative, the RPM does not report input voltage for the tower or unit.ro Integer32 UNITS "tenths of Volts" .1.3.6.1.4.1.244.1.1.4.7.2.1.2 |
slcDevRPMApparentPowerThe apparent power, in tenths of Volt-Amps, on a given RPM tower or unit. If the value is negative, the RPM does not report apparent power for the tower or unit.ro Integer32 UNITS "tenths of Volt-Amps" .1.3.6.1.4.1.244.1.1.4.7.2.1.3 |
slcDevRPMNominalApparentPowerThe nominal apparent power, in tenths of Volt-Amps, on a given RPM tower or unit. If the value is negative, the RPM does not report nominal apparent power for the tower or unit.ro Integer32 UNITS "tenths of Volt-Amps" .1.3.6.1.4.1.244.1.1.4.7.2.1.4 |
slcDevRPMRealPowerThe real power, in tenths of Watts, on a given RPM tower or unit. If the value is negative, the RPM does not report real power for the tower or unit.ro Integer32 UNITS "tenths of Watts" .1.3.6.1.4.1.244.1.1.4.7.2.1.5 |
slcDevRPMNominalRealPowerThe nominal real power, in tenths of Watts, on a given RPM tower or unit. If the value is negative, the RPM does not report nominal real power for the tower or unit.ro Integer32 UNITS "tenths of Watts" .1.3.6.1.4.1.244.1.1.4.7.2.1.6 |
slcDevRPMOutletTableTable of RPM outlet status and control entries. SEQUENCE OF SlcDevRPMOutletEntry .1.3.6.1.4.1.244.1.1.4.7.3 |
slcDevRPMOutletEntryAn entry containing status and control for outlets on an RPM. SlcDevRPMOutletEntry .1.3.6.1.4.1.244.1.1.4.7.3.1 |
slcDevRPMOutletNameThe current name of the RPM outlet. This will be blank if the RPM device does not report outlet names.ro OCTET STRING .1.3.6.1.4.1.244.1.1.4.7.3.1.1 |
slcDevRPMOutletStateThe current state of the RPM outlet.ro Enumeration .1.3.6.1.4.1.244.1.1.4.7.3.1.2 |
slcDevRPMOutletCurrentThe current level, in tenths of Amps, for the RPM outlet. This will be negative if the RPM does not report current values for the outlet.ro Integer32 UNITS "tenths of Amps" .1.3.6.1.4.1.244.1.1.4.7.3.1.3 |
slcDevRPMOutletActionPerforms an action to change the state of an outlet on an RPM. A read of this object always returns the value noAction(1). If the RPM supports individual outlet control, a command will be sent to the RPM to change the outlet state. Requests for invalid outlets or RPMs that do not support individual outlet control will return an error.rw Enumeration .1.3.6.1.4.1.244.1.1.4.7.3.1.4 |
slcConnections OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.5 |
slcConnNumberThe number of entries in the Connections table.ro Integer32 .1.3.6.1.4.1.244.1.1.5.1 |
slcConnTableTable of connection entries. The number of entries is given by the value of slcConnNumber. SEQUENCE OF SlcConnEntry .1.3.6.1.4.1.244.1.1.5.2 |
slcConnEntryAn entry containing a connection. SlcConnEntry .1.3.6.1.4.1.244.1.1.5.2.1 |
slcConnIndexReference index for each connection.ro Integer32 .1.3.6.1.4.1.244.1.1.5.2.1.1 |
slcConnEndPt1A description of one of the end points of the connection.ro OCTET STRING .1.3.6.1.4.1.244.1.1.5.2.1.2 |
slcConnEndPt2A description of one of the end points of the connection.ro OCTET STRING .1.3.6.1.4.1.244.1.1.5.2.1.3 |
slcConnFlowThe direction that data is flowing in the connection.ro Enumeration .1.3.6.1.4.1.244.1.1.5.2.1.4 |
slcConnUserThe user that initiated the connection.ro OCTET STRING .1.3.6.1.4.1.244.1.1.5.2.1.5 |
slcConnDurationThe duration, in seconds, that the connection has existed.ro Integer32 UNITS "seconds" .1.3.6.1.4.1.244.1.1.5.2.1.6 |
slcConnDurationStrThe duration, formatted in hours:minutes:seconds, that the connection has existed.ro OCTET STRING .1.3.6.1.4.1.244.1.1.5.2.1.7 |
slcConnIdleThe amount of time that the connection has been idle, in seconds.ro Integer32 UNITS "seconds" .1.3.6.1.4.1.244.1.1.5.2.1.8 |
slcConnIdleStrThe amount of time that the connection has been idle, formatted in hours:minutes:seconds.ro OCTET STRING .1.3.6.1.4.1.244.1.1.5.2.1.9 |
slcConnSourceIPFor network (Telnet and SSH) connections into the SLC, the source IP Address.ro IpAddress .1.3.6.1.4.1.244.1.1.5.2.1.10 |
slcSystem OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.6 |
slcSystemModelThe model of the SLC: SLC8, SLC16, SLC32, SLC48, SLC8008, SLC8016, SLC8024, SLC8032, SLC8040, SLC8048.ro OCTET STRING .1.3.6.1.4.1.244.1.1.6.1 |
slcSystemSerialNoThe serial number of the SLC.ro OCTET STRING .1.3.6.1.4.1.244.1.1.6.2 |
slcSystemFWRevThe firmware version of the SLC.ro OCTET STRING .1.3.6.1.4.1.244.1.1.6.3 |
slcSystemLoadViaThe method used for firmware updates.ro Enumeration .1.3.6.1.4.1.244.1.1.6.4 |
slcSystemFTPServerThe IP Address of the FTP/TFTP server used for firmware updates, and for saving and restoring configurations.ro IpAddress .1.3.6.1.4.1.244.1.1.6.5 |
slcSystemFTPPathThe path on the FTP server used for firmware updates, and for saving and restoring configurations.ro OCTET STRING .1.3.6.1.4.1.244.1.1.6.6 |
slcSystemKeypadLockIf enabled, the LCD keypad is locked for editing configuration. The keys can only be used to view settings.ro EnabledState .1.3.6.1.4.1.244.1.1.6.7 |
slcSystemTimeZoneThe time zone of the SLC.ro OCTET STRING .1.3.6.1.4.1.244.1.1.6.8 |
slcSystemWelcomeBannerThe banner displayed before the login prompt.ro OCTET STRING .1.3.6.1.4.1.244.1.1.6.9 |
slcSystemLoginBannerThe banner displayed after successful login.ro OCTET STRING .1.3.6.1.4.1.244.1.1.6.10 |
slcSystemLogoutBannerThe banner displayed after logout.ro OCTET STRING .1.3.6.1.4.1.244.1.1.6.11 |
slcSystemWebTimeoutThe timeout (in minutes) for web sessions. A value of 0 indicates that timeouts are disabled.ro Integer32 (0|5..120) UNITS "minutes" .1.3.6.1.4.1.244.1.1.6.12 |
slcSystemWebGadgetIf enabled, iGoogle Gadget web content is enabled.ro EnabledState .1.3.6.1.4.1.244.1.1.6.13 |
slcSystemActionPerforms an action on the SLC. A read of this object always returns the value noAction(1). Setting this object to rebootSLC(2) will terminate all connections and reboot the SLC. Setting this object to shutdownSLC(3) will terminate all connections and shutdown the SLC so it can be powered off.rw Enumeration .1.3.6.1.4.1.244.1.1.6.14 |
slcSystemSSHPreAuthBannerThe banner displayed prior to SSH authentication.ro OCTET STRING .1.3.6.1.4.1.244.1.1.6.15 |
slcSystemSiteRackRowThe identifier of the row of racks in a data center containing the SLC.ro Integer32 .1.3.6.1.4.1.244.1.1.6.16 |
slcSystemSiteRackClusterThe identifier of the group of racks in a given row (slcSystemSiteRackRow) containing the SLC.ro Integer32 .1.3.6.1.4.1.244.1.1.6.17 |
slcSystemSiteRackThe identifier of the rack in a given rack group (slcSystemSiteRackCluster) containing the SLC.ro Integer32 .1.3.6.1.4.1.244.1.1.6.18 |
slcSystemLCDScreensA string describing the enabled LCD screens, in the order they are displayed. Each screen is separated by a comma. The possible screens are Current Time, Network, Console, Release, Date/Time, Device Ports, Location, Temperature and User Strings.ro OCTET STRING .1.3.6.1.4.1.244.1.1.6.19 |
slcSystemLCDUserStrLine1For the LCD screen User Strings, this is the first line displayed on the LCD.ro OCTET STRING .1.3.6.1.4.1.244.1.1.6.20 |
slcSystemLCDUserStrLine2For the LCD screen User Strings, this is the second line displayed on the LCD.ro OCTET STRING .1.3.6.1.4.1.244.1.1.6.21 |
slcSystemLCDScrollingIf enabled, the LCD automatically scrolls through the enabled screens.ro EnabledState .1.3.6.1.4.1.244.1.1.6.22 |
slcSystemLCDScrollDelayIf LCD scrolling is enabled (slcSystemLCDScrolling), the delay in seconds between displaying screens.ro Integer32 .1.3.6.1.4.1.244.1.1.6.23 |
slcSystemLCDIdleDelayIf LCD scrolling is enabled (slcSystemLCDScrolling), the number of seconds after keypad input before auto-scrolling restarts.ro Integer32 .1.3.6.1.4.1.244.1.1.6.24 |
slcSystemInternalTempThe internal temperature of the SLC, given in Celsius. A value of 9999 is returned if an error is encountered reading the temperature.ro Integer32 UNITS "Celsius" .1.3.6.1.4.1.244.1.1.6.25 |
slcSystemWebProtocolThe protocol used by the web server. This setting is no longer available; the web server is configured to only support the TLS protocol.ro Enumeration .1.3.6.1.4.1.244.1.1.6.26 |
slcSystemWebCipherThe strength of the cipher used by the web server. A cipher with high strength uses 256, 168 or 128 bits; a cipher with medium strength uses 128 bits; a cipher with low strength uses 64 or 56 bits.ro Enumeration .1.3.6.1.4.1.244.1.1.6.27 |
slcSystemModelStringA string that describes the SLC model: <Model>-<Power Supply>-<PCCard or USB>ro OCTET STRING .1.3.6.1.4.1.244.1.1.6.28 |
slcSystemWebGroupThe group or groups that may access the web.ro OCTET STRING .1.3.6.1.4.1.244.1.1.6.29 |
slcSystemWebInterfaceA string describing the interfaces the web is available on; for example: Eth1,Eth2,PPP.ro OCTET STRING .1.3.6.1.4.1.244.1.1.6.30 |
slcSystemWebBannerThe banner on the web home page.ro OCTET STRING .1.3.6.1.4.1.244.1.1.6.31 |
slcSystemInternalTempLowThe minimum acceptable internal temperature for the SLC, in Celsius.ro Integer32 UNITS "Celsius" .1.3.6.1.4.1.244.1.1.6.32 |
slcSystemInternalTempHighThe maximum acceptable internal temperature for the SLC, in Celsius.ro Integer32 UNITS "Celsius" .1.3.6.1.4.1.244.1.1.6.33 |
slcSystemCalibrateTempAn offset in Celsius for calibrating the internal temperature of the SLC.ro Integer32 UNITS "Celsius" .1.3.6.1.4.1.244.1.1.6.34 |
slcSystemWebServerIf enabled, the web server will run and listen on TCP ports 80 and 443 (all requests to port 80 are redirected to port 443).ro EnabledState .1.3.6.1.4.1.244.1.1.6.35 |
slcEventObjects OBJECT IDENTIFIER .1.3.6.1.4.1.244.1.1.7 |
slcPowerSupplyIdThe identifier of the power supply in a slcEventPowerSupply trap.ro Enumeration .1.3.6.1.4.1.244.1.1.7.1 |
slcPowerSupplyActionThe action that occurred for a power supply in a slcEventPowerSupply trap.ro Enumeration .1.3.6.1.4.1.244.1.1.7.2 |
slcDevPortNumBytesThe number of bytes received on a Device Port to trigger a slcEventDevicePortData or slcEventDevicePortSLMData trap.ro Integer32 UNITS "bytes" .1.3.6.1.4.1.244.1.1.7.3 |
slcDevPortDataThe character data received on a Device Port to trigger a slcEventDevicePortData trap.ro OCTET STRING .1.3.6.1.4.1.244.1.1.7.4 |
slcDevPortStartByteThe starting byte within the logging buffer of data received on a Device Port, which triggered a slcEventDevicePortSLMData trap.ro Integer32 .1.3.6.1.4.1.244.1.1.7.5 |
slcDevPortTimeFrameThe time frame, in seconds, after which a slcEventDevicePortSLMData trap is sent to the SLM to trigger retrieval of Device Port data.ro Integer32 UNITS "seconds" .1.3.6.1.4.1.244.1.1.7.6 |
slcDevPortDeviceErrorStatusThe status returned when an error occurs in a device connected to a Device Port.ro Enumeration .1.3.6.1.4.1.244.1.1.7.7 |
slcHostnameThe hostname of the SLC sending the trap.ro OCTET STRING .1.3.6.1.4.1.244.1.1.7.8 |
slcPCCardSlotThe PC Card slot indicated for the trap.ro Enumeration .1.3.6.1.4.1.244.1.1.7.9 |
slcPCCardActionThe action that occurred on a PC Card slot.ro Enumeration .1.3.6.1.4.1.244.1.1.7.10 |
slcPCCardTypeThe type of card inserted in a PC Card slot.ro Enumeration .1.3.6.1.4.1.244.1.1.7.11 |
slcUSBActionThe action that occurred on a USB Port.ro Enumeration .1.3.6.1.4.1.244.1.1.7.12 |
slcUSBTypeThe type of device inserted in a USB Port.ro Enumeration .1.3.6.1.4.1.244.1.1.7.13 |
slcDevPortErrorStatusThe status returned when an error occurs in a Device Port. dataDrop applies to a specific Device Port and is sent when a Device Port is required to discard data in order to keep data moving for all connections to the Device Port. invalidIOConfiguration and errorIOModules apply to all Device Ports. invalidIOConfiguration is sent when the I/O modules installed in a SLC are in an invalid configuration. errorIOModules is sent when an error is detected in one or more I/O modules.ro Enumeration .1.3.6.1.4.1.244.1.1.7.14 |
slcSDCardActionThe action that occurred on the SD Card slot.ro Enumeration .1.3.6.1.4.1.244.1.1.7.15 |
slcRPMActionThe action that occurred on a Remote Power Manager.ro OCTET STRING .1.3.6.1.4.1.244.1.1.7.16 |
slcEventHostThe name or IP address of a host in a SLC event.ro OCTET STRING .1.3.6.1.4.1.244.1.1.7.17 |