L2MGMT-MIB
The Structure of Layer 2 Network Management Information.
Main OID:
swL2MgmtMIB.-.2
266
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
266 total| Object Name |
|---|
swL2MgmtMIBThe Structure of Layer 2 Network Management Information. MODULE-IDENTITY .-.2 |
swL2DevMgmt OBJECT IDENTIFIER .-.2.1 |
swL2DevInfo OBJECT IDENTIFIER .-.2.1.1 |
swDevInfoTotalNumOfPortThe number of ports within this switch. This value is the sum
of the ports within this switch.ro INTEGER .-.2.1.1.1 |
swDevInfoNumOfPortInUseThe number of ports in this switch connected to the segment or
the end stations.ro INTEGER .-.2.1.1.2 |
swDevModuleInfoTableThis table contains the module information. SEQUENCE OF SwDevModuleInfoEntry .-.2.1.1.3 |
swDevModuleInfoEntryA list of management information for each unit in the system. SwDevModuleInfoEntry .-.2.1.1.3.1 |
swDevModuleInfoUnitIDThis object indicates the specific unit ID in the stacking/chassis
table.ro INTEGER .-.2.1.1.3.1.1 |
swDevModuleInfoModuleIDThis object indicates the module ID of this unit.ro INTEGER .-.2.1.1.3.1.2 |
swDevModuleInfoModuleNameA textual string containing name of the the module.ro DisplayString .-.2.1.1.3.1.3 |
swDevModuleInfoReversionA textual string containing reversion of the module.ro DisplayString .-.2.1.1.3.1.4 |
swDevModuleInfoSerialA textual string containing serial of the module.ro DisplayString .-.2.1.1.3.1.5 |
swDevModuleInfoDescriptionA textual string containing description of the
module.ro DisplayString .-.2.1.1.3.1.6 |
swDevInfoBootPromVersionBoot Prom Version.ro DisplayString .-.2.1.1.4 |
swDevInfoFirmwareVersionFirmware Version.ro DisplayString .-.2.1.1.5 |
swDevInfoFrontPanelLedStatusThis object is a set of system LED indications. The first two
octets is defined as system LED. The first LED is power LED. The
second LED is console LED. The third LED is RPS (Redundancy
Power Supply) LED. The other octets following the second
octets are the logical port LED (following dot1dBasePort
ordering). Every two bytes are presented to a port. The first
byte is presentd to the Link/Activity LED. The second byte is
presented to the Speed LED.
Link/Activity LED :
The most significant bit is used for blink/solid:
8 = The LED blinks.
The second significant bit is used for link status:
1 = link fail.
2 = link pass.
Speed LED :
01 = 10Mbps.
02 = 100Mbps.
03 = 1000Mbps.
04 = 10Gbps.
The four remaining bits are currently unused and must be 0.ro OCTET STRING .-.2.1.1.6 |
swL2DevCtrl OBJECT IDENTIFIER .-.2.1.2 |
swL2DevCtrlStpStateThis object can be enabled or disabled spanning tree algorithm
during runtime of the system.rw Enumeration .-.2.1.2.1 |
swL2DevCtrlIGMPSnoopingThis object indicates layer 2 Internet Group Management
Protocol (IGMP) capture function is enabled or disabled.rw Enumeration .-.2.1.2.2 |
swL2DevCtrlIGMPSnoopingMcstRTOnlyrw Enumeration .-.2.1.2.3 |
swL2DevCtrlRmonStateThis object can be enabled or disabled RMON.rw Enumeration .-.2.1.2.4 |
swL2DevCtrlCleanAllStatisticCounterAs the object is set to active, all the statistic counters will
be cleared. If set to normal, do nothing.rw Enumeration .-.2.1.2.5 |
swL2DevCtrlVlanIdOfFDBTblIndicates the VLAN ID which the Dot1dTpFdbTable belongs to ;
The default value is DEFAULT_VLAN_ID of system .rw VlanId .-.2.1.2.6 |
swL2DevCtrlManagementVlanIdThis object controls which Vlan includes system ip. And the Vlan
should have been created.rw VlanId .-.2.1.2.7 |
swL2MACNotifyStateThis object can enabled or disabled MAC Notification.rw Enumeration .-.2.1.2.8 |
swL2MACNotifyHistorySizeThis object indicates the history size of variation MAC in address table.
The default value is 1 .rw INTEGER .-.2.1.2.9 |
swL2MACNotifyIntervalThis object indicates the time interval in second for trigger the MAC notify message.rw INTEGER .-.2.1.2.10 |
swL2DevCtrlWeb OBJECT IDENTIFIER .-.2.1.2.13 |
swL2DevCtrlWebStateThis object control web status.rw Enumeration .-.2.1.2.13.1 |
swL2DevCtrlWebTcpPortThis object can designate tcp port.
When web disable this object can't accessible.rw INTEGER .-.2.1.2.13.2 |
swL2DevCtrlTelnet OBJECT IDENTIFIER .-.2.1.2.14 |
swL2DevCtrlTelnetStateThis object control telnet status.rw Enumeration .-.2.1.2.14.1 |
swL2DevCtrlTelnetTcpPortThis object can designate tcp port.
When telnet disable this object can't accessible.rw INTEGER .-.2.1.2.14.2 |
swL2DevCtrlIpAutoconfigrw Enumeration .-.2.1.2.15 |
swL2DevCtrlClipagingStaterw Enumeration .-.2.1.2.17 |
swL2DevCtrlLLDPStateSpecifies the state of the LLDP function.
When this function is enabled, the switch can start to transmit
LLDP packets and receive and process the LLDP packets.
The specific function of each port will depend on the per port
LLDP setting.
For the advertisement of LLDP packets, the switch announces the
information to its neighbor through ports. For receiving
LLDP packets, the switch will learn the information from the LLDP
packets advertised from the neighbor in the neighbor table.rw Enumeration .-.2.1.2.18 |
swL2DevCtrlLLDPForwardMessageStateWhen lldp is disabled and lldp forward_message's are enabled, the
LLDP Data Unit packets received by the switch will be forwarded.rw Enumeration .-.2.1.2.19 |
swL2DevAlarm OBJECT IDENTIFIER .-.2.1.3 |
swL2DevAlarmNewRootWhen the device has become the new root of the Spanning Tree,
this object decide whether to send a new root trap.rw Enumeration .-.2.1.3.1 |
swL2DevAlarmTopologyChangeThis object determine to send a trap or not when the switch
topology was changed. If the object is enabled(3),
the topologyChange trap is sent by the device when any of its
configured ports transitions from the Learning state to the
Forwarding state, or from the Forwarding state to the Blocking
state. For the same port tranition, the device doesn't send the
trap if this object value is disabled or other.rw Enumeration .-.2.1.3.2 |
swL2DevAlarmLinkChangeThis object determine to send a trap or not when the link
was changed. If the object is enabled(3), the Link Change
trap is sent by the device when any of its ports link change.
The device doesn't send the trap if this object value is
disabled or other.rw Enumeration .-.2.1.3.3 |
swL2PortMgmt OBJECT IDENTIFIER .-.2.3 |
swL2PortInfoTableA table that contains information about every port. SEQUENCE OF SwL2PortInfoEntry .-.2.3.1 |
swL2PortInfoEntryA list of information for each port of the device. SwL2PortInfoEntry .-.2.3.1.1 |
swL2PortInfoPortIndexThis object indicates the module's port number.(1..Max port
number in the module)ro INTEGER .-.2.3.1.1.1 |
swL2PortInfoMediumTypeIndicates medium type of the port number.ro Enumeration .-.2.3.1.1.2 |
swL2PortInfoUnitIDIndicates ID of the unit in the systemro INTEGER .-.2.3.1.1.3 |
swL2PortInfoTypeThis object indicates the connector type of this port.ro Enumeration .-.2.3.1.1.4 |
swL2PortInfoLinkStatusThis object indicates the port link status.ro Enumeration .-.2.3.1.1.5 |
swL2PortInfoNwayStatusThis object indicates the port speed and duplex mode.ro Enumeration .-.2.3.1.1.6 |
swL2PortInfoErrDisReasonThis object indicates the port if disabled and why error disabled.ro Enumeration .-.2.3.1.1.7 |
swL2PortCtrlTableA table that contains control information about every port. SEQUENCE OF SwL2PortCtrlEntry .-.2.3.2 |
swL2PortCtrlEntryA list of control information for each port of the device. SwL2PortCtrlEntry .-.2.3.2.1 |
swL2PortCtrlPortIndexThis object indicates the module's port number.(1..Max port
number in the module)ro INTEGER .-.2.3.2.1.1 |
swL2PortCtrlMediumTypeIndicates medium type of the port number.ro Enumeration .-.2.3.2.1.2 |
swL2PortCtrlUnitIndexIndicates ID of the unit in the devicero INTEGER .-.2.3.2.1.3 |
swL2PortCtrlAdminStateThis object decide the port enabled or disabled.rw Enumeration .-.2.3.2.1.4 |
swL2PortCtrlNwayStateChose the port speed, duplex mode, and N-Way function mode.rw Enumeration .-.2.3.2.1.5 |
swL2PortCtrlFlowCtrlStateThe flow control mechanism is different between full duplex
mode and half duplex mode. For half duplex mode, the jamming
signal is asserted. For full duplex mode, IEEE 802.3x flow
control function sends PAUSE frames and receives PAUSE frames.rw Enumeration .-.2.3.2.1.6 |
swL2PortCtrlLockStateThis object decide the port is locked or not.rw Enumeration .-.2.3.2.1.7 |
swL2PortCtrlMACNotifyStateThis object set each poet MAC notification state.rw Enumeration .-.2.3.2.1.8 |
swL2PortCtrlAutoNegRestartIf the value of this object is set to restart(1) then this will force
auto-negotiation to begin link renegotiation. If auto-negotiation
signaling is disabled, a write to this object has no effect.
Setting the value of this object to norestart(2) has no effect.rw Enumeration .-.2.3.2.1.11 |
swL2PortCtrlAutoNegCapAdvertisedBitsA value that uniquely identifies the set of capabilities advertised
by the local auto-negotiation entity.
Capabilities in this object that are not available in
swL2PortAutoNegInfoCapabilityBits cannot be enabled.
Note that the local auto-negotiation entity may advertise some
capabilities beyond the scope of this MIB. This is indicated by
returning the bit value bOther in addition to any bit values for
standard capabilities that are listed in the
IANAifMauAutoNegCapBits TC.rw IANAifMauAutoNegCapBits .-.2.3.2.1.12 |
swL2PortCtrlJumboFrameThis object configure the switch's jumbo frame settings.rw Enumeration .-.2.3.3 |
swL2PortCtrlJumboFrameMaxSizeThis object describes how many bytes the max jumbo frame is.ro INTEGER .-.2.3.4 |
swL2PortCounterCtrlTableA table that is used to clear counter information about every port. SEQUENCE OF SwL2PortCounterCtrlEntry .-.2.3.6 |
swL2PortCounterCtrlEntryA list of entries used to clear the counter information for each port of the device. SwL2PortCounterCtrlEntry .-.2.3.6.1 |
swL2PortCounterCtrlPortIndexThis object indicates the module's port number.(1..Max port
number in the module)ro INTEGER .-.2.3.6.1.1 |
swL2PortCounterClearCtrlThis object indicates whether to clear the counters for each port of the device or not.rw Enumeration .-.2.3.6.1.2 |
swL2PortAutoNegInfoTableA table that contains information about every port's auto negotiation status. SEQUENCE OF SwL2PortAutoNegInfoEntry .-.2.3.8 |
swL2PortAutoNegInfoEntryA list of information for each port auto negotiation of the device. SwL2PortAutoNegInfoEntry .-.2.3.8.1 |
swL2PortAutoNegInfoPortIndexThis object indicates the module's port number.(1..Max port
number in the module)ro INTEGER .-.2.3.8.1.1 |
swL2PortAutoNegInfoAdminStatusIf the value of this object is disabled(2) then the interface will act as
it would if it had no auto-negotiation signaling.
The status is affect by setting swL2PortCtrlNwayState.ro Enumeration .-.2.3.8.1.2 |
swL2PortAutoNegInfoCapabilityBitsA value that uniquely identifies the set of capabilities of the local
auto-negotiation entity. Note that interfaces that support this MIB may
have capabilities that extend beyond the scope of this MIB.
Note that the local auto-negotiation entity may support some capabilities
beyond the scope of this MIB. This is indicated by returning the bit value
bOther in addition to any bit values for standard capabilities that are listed
in the IANAifMauAutoNegCapBits TC.ro IANAifMauAutoNegCapBits .-.2.3.8.1.3 |
swL2PortAutoNegInfoCapAdvertisedBitsA value that uniquely identifies the set of capabilities advertised by the
local auto-negotiation entity.
Capabilities in this object that are not available in
swL2PortAutoNegCapabilityBits cannot be enabled.
Note that the local auto-negotiation entity may advertise some capabilities
beyond the scope of this MIB. This is indicated by returning the bit value
bOther in addition to any bit values for standard capabilities that are listed
in the IANAifMauAutoNegCapBits TC.ro IANAifMauAutoNegCapBits .-.2.3.8.1.4 |
swL2PortAutoNegInfoCapReceivedBitsA value that uniquely identifies the set of capabilities received from the
remote auto-negotiation entity.
Note that interfaces that support this MIB may be attached to remote
auto-negotiation entities that have capabilities beyond the scope of this
MIB. This is indicated by returning the bit value bOther in addition to
any bit values for standard capabilities that are listed in the
IANAifMauAutoNegCapBits TC.ro IANAifMauAutoNegCapBits .-.2.3.8.1.5 |
swL2PortDropCounterTableA table that contains information for each port drop counter. SEQUENCE OF SwL2PortDropCounterEntry .-.2.3.9 |
swL2PortDropCounterEntryA list of information for each port auto negotiation of the device. SwL2PortDropCounterEntry .-.2.3.9.1 |
swL2PortDropCounterPortIndexThis object indicates the module's port number.(1..Max port
number in the module)ro INTEGER .-.2.3.9.1.1 |
swL2PortBufferFullDropsThe total number of packets discarded while buffer full.ro Counter .-.2.3.9.1.2 |
swL2PortACLDropsThe total number of packets denied by ACLs.ro Counter .-.2.3.9.1.3 |
swL2PortMulticastDropsThe total number of multicast packet that is discarded.ro Counter .-.2.3.9.1.4 |
swL2PortVLANIngressDropsThe total number of packets discarded by VLAN ingress checking.ro Counter .-.2.3.9.1.5 |
swL2QOSMgmt OBJECT IDENTIFIER .-.2.6 |
swL2QOSBandwidthControlTable. SEQUENCE OF SwL2QOSBandwidthControlEntry .-.2.6.1 |
swL2QOSBandwidthControlEntryA list of information contained in swL2QOSBandwidthControlTable. SwL2QOSBandwidthControlEntry .-.2.6.1.1 |
swL2QOSBandwidthPortIndexIndicates the port .ro INTEGER .-.2.6.1.1.1 |
swL2QOSBandwidthRxRateIndicates RX Rate(1kbit/sec) of the specifed port. Value 10000000 means no limit.rw INTEGER .-.2.6.1.1.2 |
swL2QOSBandwidthTxRateIndicates TX Rate(1kbit/sec) of the specifed port. Value 10000000 means no limit.rw INTEGER .-.2.6.1.1.3 |
swL2QOSBandwidthRadiusRxRateThe RxRate value comes from RADIUS server,
If an 802.1X port is authenticated, this value
will overwrites the locally configured RxRate.ro INTEGER .-.2.6.1.1.4 |
swL2QOSBandwidthRadiusTxRateThe TxRate value comes from RADIUS server,
If an 802.1X port is authenticated, this value
will overwrites the locally configured TxRate.ro INTEGER .-.2.6.1.1.5 |
swL2QOSSchedulingTable. SEQUENCE OF SwL2QOSSchedulingEntry .-.2.6.2 |
swL2QOSSchedulingEntryA list of information contained in swL2QOSSchedulingTable. SwL2QOSSchedulingEntry .-.2.6.2.1 |
swL2QOSSchedulingClassIndexIndicates the hardware queue number.ro INTEGER .-.2.6.2.1.1 |
swL2QOSSchedulingMaxPktsIndicates the maximum number of packets the hardware priority queue will be allowed
to transmit before allowing the next lowest priority queue to transmit its packets.
a value between 0 and 15 can be specified.rw INTEGER .-.2.6.2.1.2 |
swL2QOSSchedulingMechanismIndicates the mechanism of QOS scheduling.ro Enumeration .-.2.6.2.1.3 |
swL2QOS8021pUserPriorityTable. SEQUENCE OF SwL2QOS8021pUserPriorityEntry .-.2.6.3 |
swL2QOS8021pUserPriorityEntryA list of information contained in swL2QOS8021pUserPriorityTable. SwL2QOS8021pUserPriorityEntry .-.2.6.3.1 |
swL2QOS8021pUserPriorityIndexThe 802.1p user priority .ro INTEGER .-.2.6.3.1.1 |
swL2QOS8021pUserPriorityClassThe number of the switch's hardware priority queue. The switch has four hardware
priority queues available. They are numbered between 0 (the lowest priority)
and 6 (the highest priority).rw INTEGER .-.2.6.3.1.2 |
swL2QOS8021pDefaultPriorityTable. SEQUENCE OF SwL2QOS8021pDefaultPriorityEntry .-.2.6.4 |
swL2QOS8021pDefaultPriorityEntryA list of information contained in swL2QOS8021pDefaultPriorityTable. SwL2QOS8021pDefaultPriorityEntry .-.2.6.4.1 |
swL2QOS8021pDefaultPriorityIndexIndicates the port number .ro INTEGER .-.2.6.4.1.1 |
swL2QOS8021pDefaultPriorityThe priority value to assign to untagged packets received by the
switch ports on the switch..rw INTEGER .-.2.6.4.1.2 |
swL2QOS8021pRadiusPriorityThe value of 802.1p comes from RADIUS server.
If an 802.1X port is authenticated, this value
will overwrite the local configured value.ro INTEGER .-.2.6.4.1.3 |
swL2QOSSchedulingMechanismCtrlThis object can control QOS scheduling Mechanism.rw Enumeration .-.2.6.5 |
swL2QOSHolPreventionCtrlControl QOS Hol Preventionrw Enumeration .-.2.6.6 |
swL2PortSecurityMgmt OBJECT IDENTIFIER .-.2.7 |
swL2PortSecurityControlTableport security feature which controls the address leaning capability and the
traffic forwarding decision. Each port can have this function enabled or disabled.
When it is enabled and a number is given said N, which allows N addresses to be
learned at this port, the first N learned addresses are locked at this port as
static entry. When the learned addresses number reach N, any coming packet with
not learned source addresses are discarded (e.g. dropped) and no more new addresses
can be learned at this port. SEQUENCE OF SwL2PortSecurityControlEntry .-.2.7.1 |
swL2PortSecurityControlEntryA list of information contained in swL2PortSecurityControlTable. SwL2PortSecurityControlEntry .-.2.7.1.1 |
swL2PortSecurityPortIndexIndicates the secured port to lock address learning.ro INTEGER .-.2.7.1.1.1 |
swL2PortSecurityMaxLernAddrIndicates allowable number of addresses to be learned at this port.rw INTEGER .-.2.7.1.1.2 |
swL2PortSecurityModeIndicates the mode of locking address.
In deleteOnTimeout(3) mode - the locked addresses can be aged out after aging timer
expire. In this mode, when the locked address is aged
out, the number of address can be learned has to be
increased by one.
In deleteOnReset(4) mode - never age out the locked addresses unless restart
the system to prevent from port movement or intrusion.rw Enumeration .-.2.7.1.1.3 |
swL2PortSecurityAdmStateIndicates administration state of locking address.rw Enumeration .-.2.7.1.1.4 |
swL2PortSecurityDelCtrl OBJECT IDENTIFIER .-.2.7.2 |
swL2PortSecurityDelVlanNameIndicates vlan name.rw DisplayString .-.2.7.2.1 |
swL2PortSecurityDelPortIndicates the port.0 indicated the function isn't working now.rw INTEGER .-.2.7.2.2 |
swL2PortSecurityDelMacAddressSpecifies MAC address.rw MacAddress (SNMPv2-TC) .-.2.7.2.3 |
swL2PortSecurityDelActivity.rw Enumeration .-.2.7.2.4 |
swL2TrunkMgmt OBJECT IDENTIFIER .-.2.9 |
swL2TrunkMaxSupportedEntriesMaximum number of entries in the trunk configuration table
(swL2TrunkCtrlTable).ro INTEGER .-.2.9.1 |
swL2TrunkCurrentNumEntriesCurrent actived number of entries in the trunk configuration
table.ro INTEGER .-.2.9.2 |
swL2TrunkCtrlTableThis table specifys which ports group a set of ports(up to 8)
into a single logical link. SEQUENCE OF SwL2TrunkCtrlEntry .-.2.9.3 |
swL2TrunkCtrlEntryA list of information specifies which ports group a set of
ports(up to 8) into a single logical link. SwL2TrunkCtrlEntry .-.2.9.3.1 |
swL2TrunkIndexThe index of logical port trunk. The trunk group number depend
on the existence of unit and module.ro INTEGER .-.2.9.3.1.1 |
swL2TrunkNameThe name of logical port trunk.rw DisplayString .-.2.9.3.1.2 |
swL2TrunkMasterPortThe object indicates the master port number of the port trunk
entry. When using Port Trunk, you can not configure the other
ports of the group except the master port.
Their configuration must be same as the master port (e.g. speed,
duplex, enabled/disabled, flow control, and so on).rw INTEGER .-.2.9.3.1.3 |
swL2TrunkMemberIndicate how many number of ports is included in this Trunk.
The trunk port number depend on the existence of module.
The maximum number of ports is 8 for one trunks.rw PortList .-.2.9.3.1.4 |
swL2TrunkFloodingPortThe object indicates the flooding port number of the port trunk
entry. The first port of the trunk is implicitly configured to
be the flooding port.ro INTEGER .-.2.9.3.1.5 |
swL2TrunkTypeThis object indicated that type of the trunk group.
static : is static trunk group
lacp : is LACP trunk group .rw Enumeration .-.2.9.3.1.6 |
swL2TrunkStateThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .-.2.9.3.1.7 |
swL2TrunkActivePortsThe object indicates the active ports of the port trunk entry.ro PortList .-.2.9.3.1.8 |
swL2TrunkAlgorithmThis object configures to part of the packet examined by the
switch when selecting the egress port for transmitting
load-sharing data.rw Enumeration .-.2.9.4 |
swL2TrunkLACPPortTableThis table specifys which ports group a set of ports(up to 8)
into a single logical link. SEQUENCE OF SwL2TrunkLACPPortEntry .-.2.9.5 |
swL2TrunkLACPPortEntryA list of information specifies which ports group a set of
ports(up to 8) into a single logical link. SwL2TrunkLACPPortEntry .-.2.9.5.1 |
swL2TrunkLACPPortIndexThe index of logical port lacp.ro INTEGER .-.2.9.5.1.1 |
swL2TrunkLACPPortStateThe state of logical port lacp.rw Enumeration .-.2.9.5.1.2 |
swL2MirrorMgmt OBJECT IDENTIFIER .-.2.10 |
swL2MirrorLogicTargetPortThis object indicates switch which port will sniff another
port. A trunk port member cannot be configured as a target
Snooping port. The port number is the sequential (logical)
number which is also applied to bridge MIB, etc.rw INTEGER .-.2.10.1 |
swL2MirrorPortSourceIngressThe represent the ingress into the source port packet to
sniffed.rw PortList .-.2.10.2 |
swL2MirrorPortSourceEgressThe represent the egress from the source port packet to
sniffed.rw PortList .-.2.10.3 |
swL2MirrorPortStateThis object indicates the port mirroring state.
other(1) - this entry is currently in use but the conditions
under which it will remain so are different from each of the
following values.
disabled(2) - writing this value to the object, and then the
corresponding entry will be removed from the table.
enabled(3) - this entry is reside in the table.rw Enumeration .-.2.10.4 |
swL2IGMPMgmt OBJECT IDENTIFIER .-.2.11 |
swL2IGMPMaxSupportedVlansMaximum number of Vlans in the layer 2 IGMP control table
(swL2IGMPCtrlTable).ro INTEGER .-.2.11.1 |
swL2IGMPMaxIpGroupNumPerVlanMaximum number of multicast ip group per Vlan in the layer 2
IGMP information table (swL2IGMPQueryInfoTable).ro INTEGER .-.2.11.2 |
swL2IGMPCtrlTableThe table controls the Vlan's IGMP function. Its scale depends
on current VLAN state (swL2VlanInfoStatus). If VLAN is disabled
mode, there is only one entry in the table, with index 1. If
VLAN is in Port-Base or 802.1q mode, the number of entries can
be up to 12, with index range from 1 to 12. SEQUENCE OF SwL2IGMPCtrlEntry .-.2.11.3 |
swL2IGMPCtrlEntryThe entry in IGMP control table (swL2IGMPCtrlTable). The entry
is effective only when IGMP capture switch
(swL2DevCtrlIGMPSnooping) is enabled. SwL2IGMPCtrlEntry .-.2.11.3.1 |
swL2IGMPCtrlVidThis object indicates the IGMP control entry's VLAN id. If VLAN
is disabled, the Vid is always 0 and cannot be changed by
management users. If VLAN is in Port-Base mode, the Vid is
arranged from 1 to 12, fixed form. If VLAN is in 802.1q mode,
the Vid setting can vary from 1 to 4094 by management user, and
the Vid in each entry must be unique in the IGMP Control Table.ro INTEGER .-.2.11.3.1.1 |
swL2IGMPQueryIntervalThe frequency at which IGMP Host-Query packets are
transmitted on this switch.rw INTEGER .-.2.11.3.1.2 |
swL2IGMPMaxResponseTimeThe maximum query response time on this switch.rw INTEGER .-.2.11.3.1.3 |
swL2IGMPRobustnessThe Robustness Variable allows tuning for the expected
packet loss on a subnet. If a subnet is expected to be
lossy, the Robustness Variable may be increased. IGMP is
robust to (Robustness Variable-1) packet losses.rw INTEGER .-.2.11.3.1.4 |
swL2IGMPLastMemberQueryIntervalThe Last Member Query Interval is the Max Response Time
inserted into Group-Specific Queries sent in response to
Leave Group messages, and is also the amount of time between
Group-Specific Query messages.rw INTEGER .-.2.11.3.1.5 |
swL2IGMPHostTimeoutThe timer value for sending IGMP query packet when none was
sent by the host in the LAN. The timer works in per-VLAN basis.
Our device will be activated to send the query message if the
timer is expired. Please reference RFC2236-1997.rw INTEGER .-.2.11.3.1.6 |
swL2IGMPRouteTimeoutThe Router Timeout is how long a host must wait after hearing
a Query before it may send any IGMPv2 messages.rw INTEGER .-.2.11.3.1.7 |
swL2IGMPLeaveTimerWhen a querier receives a Leave Group message for a group that
has group members on the reception interface, it sends
Group-Specific Queries every swL2IGMPLeaveTimer to the group
being left.rw INTEGER .-.2.11.3.1.8 |
swL2IGMPQueryStateThis object decide the IGMP query enabled or disabled.rw Enumeration .-.2.11.3.1.9 |
swL2IGMPCurrentStateThis object indicates the current IGMP query state.ro Enumeration .-.2.11.3.1.10 |
swL2IGMPCtrlStateThis object indicates the status of this entry.
other(1) - this entry is currently in use but the conditions under
which it will remain so are different from each of the following
values.
disable(2) - IGMP funtion is disabled for this entry.
enable(3) - IGMP funtion is enabled for this entry.rw Enumeration .-.2.11.3.1.11 |
swL2IGMPFastLeaveStateThis object indicates the fast_leave status of this entry.
other(1) - this entry is currently in use but the conditions under
which it will remain so are different from each of the following
values.
disable(2) - IGMP fast-leave funtion is disabled for this entry.
enable(3) - IGMP fast-leave funtion is enabled for this entry.rw Enumeration .-.2.11.3.1.12 |
swL2IGMPQueryVersionConfigure the IGMP version of query packet which will be sent by the router.rw INTEGER .-.2.11.3.1.13 |
swL2IGMPReportSuppressionWhen enabled, multiple IGMP reports or leaves for a specific group (S,G)
will be integrated into only one report before being sent to the router
port.rw Enumeration .-.2.11.3.1.15 |
swL2IGMPQueryInfoTableThe table contains the number current IGMP query packets which
is captured by this device, as well as the IGMP query packets
sent by the device. SEQUENCE OF SwL2IGMPQueryInfoEntry .-.2.11.4 |
swL2IGMPQueryInfoEntryInformation about current IGMP query information, provided that
swL2DevCtrlIGMPSnooping and swL2IGMPCtrState of associated VLAN
entry are all enabled. SwL2IGMPQueryInfoEntry .-.2.11.4.1 |
swL2IGMPInfoVidThis object indicates the Vid of associated IGMP info table
entry. It follows swL2IGMPCtrlVid in the associated entry of
IGMP control table (swL2IGMPCtrlTable).ro INTEGER .-.2.11.4.1.1 |
swL2IGMPInfoQueryCountThis object indicates the number of query packets received
since the IGMP function enabled, in per-VLAN basis.ro INTEGER .-.2.11.4.1.2 |
swL2IGMPInfoTxQueryCountThis object indicates the send count of IGMP query messages, in
per-VLAN basis. In case of IGMP timer expiration, the switch
sends IGMP query packets to related VLAN member ports and
increment this object by 1.ro INTEGER .-.2.11.4.1.3 |
swL2IGMPInfoTableThe table containing current IGMP information which captured by
this device, provided that swL2DevCtrlIGMPSnooping and
swL2IGMPCtrlState of associated VLAN entry are all enabled. Note
that the priority of IGMP table entries is lower than Filtering
Table, i.e. if there is a table hash collision between the
entries of IGMP Table and Filtering Table inside the switch H/W
address table, then Filtering Table entry overwrite the
colliding entry of IGMP Table. See swL2FilterMgmt description
also. SEQUENCE OF SwL2IGMPInfoEntry .-.2.11.5 |
swL2IGMPInfoEntryInformation about current IGMP information which captured by
this device, provided that swL2DevCtrlIGMPSnooping and
swL2IGMPCtrlState of associated VLAN entry are all enabled. SwL2IGMPInfoEntry .-.2.11.5.1 |
swL2IGMPVidThis object indicates the Vid of individual IGMP table entry.
It shows the Vid of IGMP report information captured on
network.ro INTEGER .-.2.11.5.1.1 |
swL2IGMPGroupIpAddrThis object is identify group ip address which is captured from
IGMP packet, in per-Vlan basis.ro IpAddress .-.2.11.5.1.2 |
swL2IGMPMacAddrThis object is identify mac address which is corresponding
to swL2IGMPGroupIpAddr, in per-Vlan basis.ro MacAddress (SNMPv2-TC) .-.2.11.5.1.3 |
swL2IGMPPortMapThis object indicates which ports are belong to the same
multicast group, in per-Vlan basis. Each multicast group has a
octect string to indicate with port map. The most significant
bit represents the lowest numbered port, and the least
significant bit represents the highest numbered port. Thus, each
port of the switch is represented by a single bit within the
value of this object. If that bit has a value of '1' then that
port is included in the set of ports; the port is not included
if its bit has a value of '0'(Note that the setting of the bit
corresponding to the port from which a frame is received is
irrelevant). The 4 octets is represent one unit port according
its logic port. If the unit less 32 port, the other port don't
care just fill zero.ro PortList .-.2.11.5.1.4 |
swL2IGMPIpGroupReportCountThis object indicate how much report packet was receive by our
device corresponding with this entry from IGMP function enabled,
in per-Vlan basis.ro INTEGER .-.2.11.5.1.5 |
swL2IGMPRouterPortsTableThe table controls the Vlan's IGMP router ports function. SEQUENCE OF SwL2IGMPRouterPortsEntry .-.2.11.6 |
swL2IGMPRouterPortsEntryThe entry in IGMP router ports table (swL2IGMPRouterPortsTable). SwL2IGMPRouterPortsEntry .-.2.11.6.1 |
swL2IGMPRouterPortsVidThis object indicates the IGMP router ports entry's VLAN id. If VLAN
is disabled, the Vid is always 0 and cannot be changed by
management users. If VLAN is in Port-Base mode, the Vid is
arranged from 1 to 12, fixed form. If VLAN is in 802.1q mode,
the Vid setting can vary from 1 to 4094 by management user, and
the Vid in each entry must be unique in the IGMP ports Table.ro INTEGER .-.2.11.6.1.1 |
swL2IGMPRouterStaticPortListrw PortList .-.2.11.6.1.2 |
swL2IGMPRouterDynamicPortListro PortList .-.2.11.6.1.3 |
swL2IGMPRouterForbiddenPortListrw PortList .-.2.11.6.1.4 |
swL2IGMPMulticastVlanTableThe information of the IGMP snooping multicast VLAN table. SEQUENCE OF SwL2IGMPMulticastVlanEntry .-.2.11.7 |
swL2IGMPMulticastVlanEntryThe entry of swL2IGMPMulticastVlanTable. SwL2IGMPMulticastVlanEntry .-.2.11.7.1 |
swL2IGMPMulticastVlanidThis object indicates the VLAN ID of the IGMP snooping multicast
VLAN entry.ro INTEGER .-.2.11.7.1.1 |
swL2IGMPMulticastVlanNameThis object indicates the VLAN name of the IGMP snooping multicast
VLAN entry.rw DisplayString .-.2.11.7.1.2 |
swL2IGMPMulticastVlanSourcePortThis object indicate the portlist of the source ports of IGMP
snooping multicast VLAN. The source ports will be set as tag ports
of the VLAN entry. And the IGMP control messages received from the
member ports would be forwarded to the source ports.rw PortList .-.2.11.7.1.3 |
swL2IGMPMulticastVlanMemberPortThis object indicate the portlist of the member ports of the IGMP
snooping multicast VLAN. The source ports will be set as untagged ports
of the VLAN entry. And the IGMP control messages received from the
member ports would be forwarded to the source ports.rw PortList .-.2.11.7.1.4 |
swL2IGMPMulticastVlanTagMemberPortThis object indicate the portlist of the tag member ports of IGMP
snooping multicast VLAN.rw PortList .-.2.11.7.1.5 |
swL2IGMPMulticastVlanStateThis object can be enabled or disabled IGMP_snooping multicast VLAN.rw Enumeration .-.2.11.7.1.6 |
swL2IGMPMulticastVlanReplaceSourceIpThe replace source IP of this multicast vlan.rw IpAddress .-.2.11.7.1.7 |
swL2IGMPMulticastVlanRowStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .-.2.11.7.1.8 |
swL2IGMPMulticastVlanRemoveAllMcastAddrListActionThis object indicates if remove all the multicast address
list from the IGMP multicast VLAN or not.rw Enumeration .-.2.11.7.1.9 |
swL2IGMPMulticastVlanGroupTableThe table containing the IGMP snooping multicast VLAN group information SEQUENCE OF SwL2IGMPMulticastVlanGroupEntry .-.2.11.8 |
swL2IGMPMulticastVlanGroupEntryInformation about current IGMP snooping multicast VLAN group. SwL2IGMPMulticastVlanGroupEntry .-.2.11.8.1 |
swL2IGMPMulticastVlanGroupVidThis object indicates the Vid of IGMP snooping multicast VLAN group.ro INTEGER .-.2.11.8.1.1 |
swL2IGMPMulticastVlanGroupFromIpSpecifies the multicast address list for this VLAN.ro IpAddress .-.2.11.8.1.2 |
swL2IGMPMulticastVlanGroupToIpSpecifies the multicast address list for this VLAN.ro IpAddress .-.2.11.8.1.3 |
swL2IGMPMulticastVlanGroupStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .-.2.11.8.1.4 |
swIGMPSnoopingGroupTableThe table contains the current IGMP snooping group information captured by
the device. SEQUENCE OF SwIGMPSnoopingGroupEntry .-.2.11.11 |
swIGMPSnoopingGroupEntryInformation about the current IGMP snooping group information which has been captured by
the device. SwIGMPSnoopingGroupEntry .-.2.11.11.1 |
swIGMPSnoopingGroupVidThis object indicates the VID of the individual IGMP snooping group table entry.ro INTEGER .-.2.11.11.1.1 |
swIGMPSnoopingGroupGroupAddrThis object identifies the group IP address which have been captured from
the IGMP packet, on a per-VLAN basis.ro IpAddress .-.2.11.11.1.2 |
swIGMPSnoopingGroupSourceAddrThis object identifies the source addresses.ro IpAddress .-.2.11.11.1.3 |
swIGMPSnoopingGroupIncludePortMapThis object indicates the port list under INCLUDE mode.ro PortList .-.2.11.11.1.4 |
swIGMPSnoopingGroupExcludePortMapThis object indicates the port list under EXCLUDE mode.ro PortList .-.2.11.11.1.5 |
swL2IGMPSnoopingStaticGroupTableThe table contains the current IGMP snooping static group information captured by
the device. SEQUENCE OF SwL2IGMPSnoopingStaticGroupEntry .-.2.11.16 |
swL2IGMPSnoopingStaticGroupEntryInformation about current IGMP snooping static group information captured by
the device. SwL2IGMPSnoopingStaticGroupEntry .-.2.11.16.1 |
swL2IGMPSnoopingStaticGroupVIDThis object indicates the VID of the current IGMP snooping static group.ro INTEGER .-.2.11.16.1.1 |
swL2IGMPSnoopingStaticGroupIPaddressThis object indicates the current IGMP snooping static group IP address.ro IpAddress .-.2.11.16.1.2 |
swL2IGMPSnoopingStaticGroupMemberPortListThis object indicates the current IGMP snooping static group Member Portlist.rw PortList .-.2.11.16.1.3 |
swL2IGMPSnoopingStaticGroupRowStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .-.2.11.16.1.4 |
swL2TrafficSegMgmt OBJECT IDENTIFIER .-.2.14 |
swL2TrafficSegTableThis table specifys the port just can forward traffic to the
specific port list. SEQUENCE OF SwL2TrafficSegEntry .-.2.14.1 |
swL2TrafficSegEntryA list of information specifies the port with its traffic
forward list. SwL2TrafficSegEntry .-.2.14.1.1 |
swL2TrafficSegPortThe port number of the logical port.ro INTEGER .-.2.14.1.1.1 |
swL2TrafficSegForwardPortsThe port list that the specific port can forward traffic.rw PortList .-.2.14.1.1.2 |
swL2MgmtMIBTraps OBJECT IDENTIFIER .-.2.16 |
swL2Notify OBJECT IDENTIFIER .-.2.16.1 |
swL2NotifyPrefix OBJECT IDENTIFIER .-.2.16.1.2 |
swL2NotifFirmware OBJECT IDENTIFIER .-.2.16.1.2.0 |
swL2LoopDetectedNotify OBJECT IDENTIFIER .-.2.16.1.2.0.0 |
swL2PortLoopOccurredThe trap is sent when Port loop occurred. NOTIFICATION-TYPE .-.2.16.1.2.0.0.3 |
swL2PortLoopRestartThe trap is sent when Port loop restart after interval time. NOTIFICATION-TYPE .-.2.16.1.2.0.0.4 |
swL2VlanLoopOccurredThe trap is sent when Port with VID loop occurred. NOTIFICATION-TYPE .-.2.16.1.2.0.0.5 |
swL2VlanLoopRestartThe trap is sent when Port with VID loop restart after interval time. NOTIFICATION-TYPE .-.2.16.1.2.0.0.6 |
swL2macNotificationThis trap indicates the mac addresses variation in address table . NOTIFICATION-TYPE .-.2.16.1.2.0.1 |
swl2NotificationBidings OBJECT IDENTIFIER .-.2.16.1.2.1 |
swL2macNotifyInfoThis object indicates the last time reboot information.ro OCTET STRING .-.2.16.1.2.1.1 |
swL2VlanLoopDetectVIDThis object indicates the VID that has detected a loopback.ro INTEGER .-.2.16.1.2.1.3 |
swL2LoopDetectCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.3.2.18.1 |
swL2LoopDetectAdminStateThis object indicates the loopback detection status for the system.rw Enumeration .1.3.6.1.4.1.171.11.63.3.2.18.1.1 |
swL2LoopDetectIntervalThis object indicates the interval value, the range is from 1 to 32767 seconds.rw INTEGER .1.3.6.1.4.1.171.11.63.3.2.18.1.2 |
swL2LoopDetectRecoverTimeThis object indicates the recover time, the range is from 60 to 1000000.
The value of 0 disables the recover function.rw INTEGER .1.3.6.1.4.1.171.11.63.3.2.18.1.3 |
swL2LoopDetectModeThis object indicates the loopback detection mode for the system.rw Enumeration .1.3.6.1.4.1.171.11.63.3.2.18.1.4 |
swL2LoopDetectTrapModeThis object indicates the loopback detection trap mode for the system.rw Enumeration .1.3.6.1.4.1.171.11.63.3.2.18.1.5 |
swL2LoopDetectPortMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.3.2.18.2 |
swL2LoopDetectPortTableThe table specifies the loopback detection function specified by port. SEQUENCE OF SwL2LoopDetectPortEntry .1.3.6.1.4.1.171.11.63.3.2.18.2.1 |
swL2LoopDetectPortEntryThe table specifies the loopback detection function specified by port. SwL2LoopDetectPortEntry .1.3.6.1.4.1.171.11.63.3.2.18.2.1.1 |
swL2LoopDetectPortIndexThis object indicates the module's port number. The range is from 1 to
the maximum port number specified in the modulero INTEGER .1.3.6.1.4.1.171.11.63.3.2.18.2.1.1.1 |
swL2LoopDetectPortStateThis object indicates the loopback detection function state on the port.rw Enumeration .1.3.6.1.4.1.171.11.63.3.2.18.2.1.1.2 |
swL2LoopDetectPortLoopVLANThis object indicates the VLAN list that has detected a loopback.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.11.63.3.2.18.2.1.1.3 |
swL2LoopDetectPortLoopStatusThis object indicates the port status.ro Enumeration .1.3.6.1.4.1.171.11.63.3.2.18.2.1.1.4 |
swL2IpLimitedMulticastTableThis entity's per-port Limited IP multicast address range table. SEQUENCE OF SwL2IpLimitedMulticastEntry .1.3.6.1.4.1.171.11.70.9.2.15.1 |
swL2IpLimitedMulticastEntryA particular route to a particular destination, under a particular policy.
Once an entry be built,it shouldn't be modified.That is,it just support create and
delete action. SwL2IpLimitedMulticastEntry .1.3.6.1.4.1.171.11.70.9.2.15.1.1 |
swL2IpLimitedMulticastPortIndexA port to config the limited multicast address.ro INTEGER .1.3.6.1.4.1.171.11.70.9.2.15.1.1.1 |
swL2IpLimitedMulticastHeadThe head of multicast address range.rw IpAddress .1.3.6.1.4.1.171.11.70.9.2.15.1.1.2 |
swL2IpLimitedMulticastTailThe tail of multicast address range.rw IpAddress .1.3.6.1.4.1.171.11.70.9.2.15.1.1.3 |
swL2IpLimitedMulticastAccessIt allow you to permit or deny multicast range.rw Enumeration .1.3.6.1.4.1.171.11.70.9.2.15.1.1.4 |
swL2IpLimitedMulticastStateEnable or disable limited multicast address for the chosen portlist.rw Enumeration .1.3.6.1.4.1.171.11.70.9.2.15.1.1.5 |
swL2IpLimitedMulticastDelStateEnable or disable delete limited multicast address for the chosen portlist.rw Enumeration .1.3.6.1.4.1.171.11.70.9.2.15.1.1.6 |
swL2MultiFilterTableA table that contains infomation about vlan multicast filter mode. SEQUENCE OF SwL2MultiFilterEntry .1.3.6.1.4.1.171.11.113.1.2.2.22.1 |
swL2MultiFilterEntryA list of multicast filter mode information for each vlan. SwL2MultiFilterEntry .1.3.6.1.4.1.171.11.113.1.2.2.22.1.1 |
swL2MultiFilterVidvid for each vlanro INTEGER .1.3.6.1.4.1.171.11.113.1.2.2.22.1.1.1 |
swL2MultiFilterModevlan multicast filter mode.rw Enumeration .1.3.6.1.4.1.171.11.113.1.2.2.22.1.1.2 |
swL2VlanTableA table containing current configuration information
for each VLAN currently configured into the device by
(local or network) management, or dynamically created
as a result of GVRP requests received. SEQUENCE OF SwL2VlanEntry .1.3.6.1.4.1.2272.1.201.1.2.7.1 |
swL2VlanEntryInformation for a VLAN configured into the device by
(local or network) management, or dynamically created
as a result of GVRP requests received. SwL2VlanEntry .1.3.6.1.4.1.2272.1.201.1.2.7.1.1 |
swL2VlanIndexThe VLAN ID of the VLAN to be created. The range is 1 - 4094. VlanId .1.3.6.1.4.1.2272.1.201.1.2.7.1.1.1 |
swL2VlanNameThe name of the VLAN to be displayed.ro DisplayString .1.3.6.1.4.1.2272.1.201.1.2.7.1.1.2 |
swL2VlanTypeThe type of the VLAN to be displayed.ro Enumeration .1.3.6.1.4.1.2272.1.201.1.2.7.1.1.3 |
swL2VlanMemberPortsA range of member ports to the VLAN.ro PortList .1.3.6.1.4.1.2272.1.201.1.2.7.1.1.4 |
swL2VlanStaticPortsA range of static ports to the VLAN.ro PortList .1.3.6.1.4.1.2272.1.201.1.2.7.1.1.5 |
swL2VlanStaticTaggedPortsSpecifies the additional ports as tagged.ro PortList .1.3.6.1.4.1.2272.1.201.1.2.7.1.1.6 |
swL2VlanStaticUntaggedPortsSpecifies the additional ports as untagged.ro PortList .1.3.6.1.4.1.2272.1.201.1.2.7.1.1.7 |
swL2VlanForbiddenPortsThe set of ports which are prohibited by management
from being included in the egress list for this VLAN.
Changes to this object that cause a port to be included
or excluded affect the per-port per-VLAN Registrar
control for Registration Forbidden for the relevant GVRP
state machine on each port. A port may not be added in
this set if it is already a member of the set of ports
in dot1qVlanStaticEgressPorts. The default value of
this object is a string of zeros of appropriate length,
excluding all ports from the forbidden set.ro PortList .1.3.6.1.4.1.2272.1.201.1.2.7.1.1.8 |
swL2VlanCurrentTaggedPortsThe set of ports which are transmitting traffic for
this VLAN as tagged frames.ro PortList .1.3.6.1.4.1.2272.1.201.1.2.7.1.1.9 |
swL2VlanCurrentUntaggedPortsThe set of ports which are transmitting traffic for
this VLAN as untagged frames.ro PortList .1.3.6.1.4.1.2272.1.201.1.2.7.1.1.10 |
swL2VlanAdvertisementStateSpecifies the VLAN as able to join GVRP If this parameter
is not set, the VLAN cannot be configured to have forbidden ports.
This flag protocol VLAN is fixed to DISABLE.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.7.1.1.11 |
swL2PVIDAutoAssignmentStateThis object controls the PVID auto assigment state.
If 'Auto-assign PVID' is disabled, PVID only be changed
by PVID configuration (user changes explicitly). The VLAN
configuration will not automatically change PVID.
If 'Auto-assign PVID' is enabled, PVID will be possibly
changed by PVID or VLAN configuration. When user configures
a port to VLAN X's untagged membership, this port's PVID
will be updated with VLAN X. In the form of VLAN list command,
PVID is updated with last item of VLAN list. When user removes
a port from the untagged membership of the PVID's VLAN, the
port's PVID will be assigned with 'default VLAN'.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.7.2 |