JUNIPER-WX-EVENT-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
Imported Objects
Objects
14 total| Object Name |
|---|
jnxWxGrpEventV2Branch for SNMPv2 events. The OIDs for SNMPv2 events should
have a zero as the next-to-last sub-identifier (as specified
in RFC1902). OBJECT IDENTIFIER .1.3.6.1.4.1.2636.3.41.1.1.3.0 |
jnxWxGrpEventPowerSupplyFailureOne or more sources of power to the system have failed.
A redundant power-supply has presumably taken over. NOTIFICATION-TYPE .1.3.6.1.4.1.2636.3.41.1.1.3.0.1 |
jnxWxGrpEventPowerSupplyOkOne or more previously failed sources of power is now
working normally. The transition to normal condition happened
without the system having to be restarted. NOTIFICATION-TYPE .1.3.6.1.4.1.2636.3.41.1.1.3.0.2 |
jnxWxGrpEventLicenseWillExpireThe license for the system is about to
expire shortly. When it eventually does
expire, the system will switch over to
and stay in pass-through mode. NOTIFICATION-TYPE .1.3.6.1.4.1.2636.3.41.1.1.3.0.3 |
jnxWxGrpEventThruputLimitExceededThe throughput of traffic through the device
has exceeded the limit for which it has
been licensed. NOTIFICATION-TYPE .1.3.6.1.4.1.2636.3.41.1.1.3.0.4 |
jnxWxGrpEventLicenseExpiredThe license for the system expired.
As a result, the system will switch over to
and stay in pass-through mode. NOTIFICATION-TYPE .1.3.6.1.4.1.2636.3.41.1.1.3.0.5 |
jnxWxGrpEventClientLimitExceededExceeded licensed maximum concurrent client connections.
Please contact Juniper Networks to obtain a new license
with higher number of concurrent client connections. NOTIFICATION-TYPE .1.3.6.1.4.1.2636.3.41.1.1.3.0.6 |
jnxWxGrpEventInFailSafeModeThis trap is sent when the device boots up in fail-safe mode.
This can happen for one of the following reasons:
Fail-safe reboot was explicitly initiated by the user.
The device rebooted automatically too many times because of
the failure of internal consistency checks or the failure of
tests that verify proper operation of the device. NOTIFICATION-TYPE .1.3.6.1.4.1.2636.3.41.1.1.3.0.7 |
jnxWxGrpEventInterfaceSpeedMismatchA mismatch is detected between the local and remote
interface settings. This can happen due to a mismatch
in the local and remote interface speed or mode. NOTIFICATION-TYPE .1.3.6.1.4.1.2636.3.41.1.1.3.0.8 |
jnxWxGrpEventInterfaceSpeedOkA mismatch previously detected between the local and remote
interface settings is now resolved. The local and remote
interface speed and mode are matched. NOTIFICATION-TYPE .1.3.6.1.4.1.2636.3.41.1.1.3.0.9 |
jnxWxGrpEventInterfaceDuplexMismatchA possible mismatch was detected between the duplex settings
of either the local or remote interface and that of the
device attached to that interface. The interface (local
or remote) is identified by the 'ifIndex' object.
Note that this notification is quite different from
jnxWxGrpEventInterfaceSpeedMismatch, which compares the
local and remote interfaces on the same WX device. NOTIFICATION-TYPE .1.3.6.1.4.1.2636.3.41.1.1.3.0.10 |
jnxWxGrpEventLoginFailureA user's login attempt via the console/ssh/web server
failed due to incorrect username or password. NOTIFICATION-TYPE .1.3.6.1.4.1.2636.3.41.1.1.3.0.11 |
jnxWxGrpEventDiskFailureA hard disk failed on the system. The system was rebooted,
and will now operate without the downed disk, at a degraded
performance. Dictionary accumulated until this point was lost. NOTIFICATION-TYPE .1.3.6.1.4.1.2636.3.41.1.1.3.0.12 |
jnxWxGrpEventDescrString that provides a textual description of the event.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2636.3.41.1.1.3.1 |
More MIBs from Juniper Networks
Browse all Juniper NetworksMIBs →The JUNIPER-CHASSIS-DEFINES-MIB establishes the foundational Object Identifier (OID) namespace and data type definitions required to map and identify specific Juniper chassis hardware platforms and their internal physical components. This module serves as the structural prerequisite for the JUNIPER-CHASSIS-MIB, enabling the retrieval of inventory data, component status, and hardware topology details for Juniper MX, PTX, and EX series devices.
The JUNIPER-MOBILE-GATEWAY-GTP-MIB provides SNMP objects for monitoring GTP (GPRS Tunneling Protocol) session states, tunnel endpoints, and protocol counters on Juniper mobile gateway platforms. It enables administrators to track GTP-C and GTP-U traffic statistics, error conditions, and active tunnel metrics essential for validating mobile core network connectivity.
SNMP MIB module
SNMP MIB module
The JUNIPER-MOBILE-GATEWAY-SGW-GTP-MIB module enables monitoring of GTP (GPRS Tunneling Protocol) session states and traffic counters on Juniper Mobile Gateway Serving Gateways (SGW). It provides specific objects for tracking GTP-C and GTP-U tunnel establishment, teardown, and packet throughput metrics essential for validating mobile core network connectivity.
The JUNIPER-IPSEC-FLOW-MON-MIB monitors Juniper Networks IPsec VPN infrastructure by exposing tables for IKE tunnels, IPSec tunnels, and IPSec security associations to track tunnel states, association parameters, and flow statistics. This module facilitates the management of IPsec security policies and the operational status of encrypted traffic flows within the device's security architecture.