JUNIPER-IPv4-MIB
Updated Jul 18, 2003The JUNIPER-IPv4-MIB module extends the standard IF-MIB interface table to provide Juniper Networks devices with vendor-specific monitoring of IPv4 interface statistics and operational states. This extension enables precise tracking of IPv4 traffic counters, address bindings, and interface-level performance metrics within Junos OS environments.
Imported Objects
Objects
9 total| Object Name |
|---|
jnxIpv4The MIB modules extends the ifTable as
defined in IF-MIB. MODULE-IDENTITY .1.3.6.1.4.1.2636.3.12 |
jnxIpv4Config OBJECT IDENTIFIER .1.3.6.1.4.1.2636.3.12.1 |
jnxIpv4AddrTableThe table of addressing information relevant to this
entity's IP addresses. SEQUENCE OF JnxIpv4AddrEntry .1.3.6.1.4.1.2636.3.12.1.1 |
jnxIpv4AddrEntryThe addressing information for one of this entity's IP
addresses. JnxIpv4AddrEntry .1.3.6.1.4.1.2636.3.12.1.1.1 |
jnxIpv4AdEntIfIndexThe index value which uniquely identifies the interface to
which this entry is applicable. The interface identified by
a particular value of this index is the same interface as
identified by the same value of RFC 1573's ifIndex. INTEGER .1.3.6.1.4.1.2636.3.12.1.1.1.1 |
jnxIpv4AdEntAddrThe IP address to which this entry's addressing information
pertains. IpAddress .1.3.6.1.4.1.2636.3.12.1.1.1.2 |
jnxIpv4AdEntNetMaskThe subnet mask associated with the IP address of this
entry. The value of the mask is an IP address with all the
network bits set to 1 and all the hosts bits set to 0.ro IpAddress .1.3.6.1.4.1.2636.3.12.1.1.1.3 |
jnxIpv4AdEntBcastAddrThe value of the least-significant bit in the IP broadcast
address used for sending datagrams on the (logical)
interface associated with the IP address of this entry. For
example, when the Internet standard all-ones broadcast
address is used, the value will be 1. This value applies to
both the subnet and network broadcasts addresses used by the
entity on this (logical) interface.ro INTEGER .1.3.6.1.4.1.2636.3.12.1.1.1.4 |
jnxIpv4AdEntReasmMaxSizeThe size of the largest IP datagram which this entity can
re-assemble from incoming IP fragmented datagrams received
on this interface.ro INTEGER .1.3.6.1.4.1.2636.3.12.1.1.1.5 |
More MIBs from Juniper Networks
Browse all Juniper NetworksMIBs →The JUNIPER-CHASSIS-DEFINES-MIB establishes the foundational Object Identifier (OID) namespace and data type definitions required to map and identify specific Juniper chassis hardware platforms and their internal physical components. This module serves as the structural prerequisite for the JUNIPER-CHASSIS-MIB, enabling the retrieval of inventory data, component status, and hardware topology details for Juniper MX, PTX, and EX series devices.
The JUNIPER-MOBILE-GATEWAY-GTP-MIB provides SNMP objects for monitoring GTP (GPRS Tunneling Protocol) session states, tunnel endpoints, and protocol counters on Juniper mobile gateway platforms. It enables administrators to track GTP-C and GTP-U traffic statistics, error conditions, and active tunnel metrics essential for validating mobile core network connectivity.
SNMP MIB module
SNMP MIB module
The JUNIPER-MOBILE-GATEWAY-SGW-GTP-MIB module enables monitoring of GTP (GPRS Tunneling Protocol) session states and traffic counters on Juniper Mobile Gateway Serving Gateways (SGW). It provides specific objects for tracking GTP-C and GTP-U tunnel establishment, teardown, and packet throughput metrics essential for validating mobile core network connectivity.
The JUNIPER-IPSEC-FLOW-MON-MIB monitors Juniper Networks IPsec VPN infrastructure by exposing tables for IKE tunnels, IPSec tunnels, and IPSec security associations to track tunnel states, association parameters, and flow statistics. This module facilitates the management of IPsec security policies and the operational status of encrypted traffic flows within the device's security architecture.