JUNIPER-ATM-MIB
Updated Dec 4, 2003AI MIB Summary
The JUNIPER-ATM-MIB enables monitoring and management of Asynchronous Transfer Mode (ATM) interfaces and Virtual Circuits (VCs) on Juniper Networks hardware. It provides access to specific ATM performance counters, interface status states, and VC configuration parameters for troubleshooting and capacity planning.
The Juniper enterprise MIB for ATM interfaces and VCs
Main OID:
jnxAtm.1.3.6.1.4.1.2636.3.10
77
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
77 total| Object Name |
|---|
jnxAtmThe Juniper enterprise MIB for ATM interfaces and VCs MODULE-IDENTITY .1.3.6.1.4.1.2636.3.10 |
jnxAtmIfTableThis table contains config and stats parameters, one entry per
physical interface (ATM port). SEQUENCE OF JnxAtmIfEntry .1.3.6.1.4.1.2636.3.10.1 |
jnxAtmIfEntryThis entry contains additional ATM interface config and stats
objects, not covered in standard mibs. Each entry is an extension
of atmInterfaceConfEntry defined in ATM-MIB. JnxAtmIfEntry .1.3.6.1.4.1.2636.3.10.1.1 |
jnxAtmIfPortTypeThe physical port type.ro Enumeration .1.3.6.1.4.1.2636.3.10.1.1.1 |
jnxAtmIfEncapsATM physical link layer encapsulation.ro Enumeration .1.3.6.1.4.1.2636.3.10.1.1.2 |
jnxAtmIfLpBackInfoLoop back config and type.ro Enumeration .1.3.6.1.4.1.2636.3.10.1.1.3 |
jnxAtmIfScrambleEnableShows whether scrambling is enabled or disabledro Enumeration .1.3.6.1.4.1.2636.3.10.1.1.4 |
jnxAtmIfTxCellCountThe number of ATM cells transmitted by the interface.
Includes Idle cells transmitted.ro Counter64 .1.3.6.1.4.1.2636.3.10.1.1.5 |
jnxAtmIfRxCellCountThe number of ATM cells received by the interface.
Excludes Idle cells received.ro Counter64 .1.3.6.1.4.1.2636.3.10.1.1.6 |
jnxAtmIfTxIdleCellCountThe number of idle cells sent by the port. When the ATM interface
has nothing to send, it sends idle cells to fill the time slot.ro Counter64 .1.3.6.1.4.1.2636.3.10.1.1.7 |
jnxAtmIfUncorrHCSErrsThe number of uncorrectable cell Header Check Sequence (HCS) Errors
that occurred.ro Counter64 .1.3.6.1.4.1.2636.3.10.1.1.8 |
jnxAtmIfCorrHCSErrsThe number of correctable cell Header Check Sequence (HCS) Errors
that occurred.ro Counter64 .1.3.6.1.4.1.2636.3.10.1.1.9 |
jnxAtmIfTxCellFIFOOverRunsThe number of overruns in the Transmit FIFO.ro Counter64 .1.3.6.1.4.1.2636.3.10.1.1.10 |
jnxAtmIfRxCellFIFOOverRunsThe number of overruns in the Receive FIFO.ro Counter64 .1.3.6.1.4.1.2636.3.10.1.1.11 |
jnxAtmIfRxCellFIFOUnderRunsThe number of underruns in the receive FIFO.ro Counter64 .1.3.6.1.4.1.2636.3.10.1.1.12 |
jnxAtmIfInInvalidVCCellsThe number of Cells that arrived for non existent VC.ro Counter64 .1.3.6.1.4.1.2636.3.10.1.1.13 |
jnxAtmIfInNoBufferOAMCellsThe number of received OAM cells or raw cells dropped because
no buffers were available to handle them.ro Counter64 .1.3.6.1.4.1.2636.3.10.1.1.14 |
jnxAtmIfInNoBufDropPktsThe number of AAL5 packets dropped because there was no enough
buffer to handle them.ro Counter64 .1.3.6.1.4.1.2636.3.10.1.1.15 |
jnxAtmIfOutVCQueueDropsThe number of packets dropped because of queue limits on each VC.ro Counter64 .1.3.6.1.4.1.2636.3.10.1.1.16 |
jnxAtmIfInBadCrcsThe total number of incoming CRC errors.ro Counter64 .1.3.6.1.4.1.2636.3.10.1.1.17 |
jnxAtmIfInLenErrPktsThe number of AAL5 packets dropped because their length was incorrect.ro Counter64 .1.3.6.1.4.1.2636.3.10.1.1.18 |
jnxAtmIfInTimeoutPktsThe number of AAL5 packets dropped because of reassembly timeout.ro Counter64 .1.3.6.1.4.1.2636.3.10.1.1.19 |
jnxAtmIfL2CircuitModeThe layer 2 circuit mode of this Atm interface. Note, this
applies only to interfaces on AtmII pics.ro Enumeration .1.3.6.1.4.1.2636.3.10.1.1.20 |
jnxAtmVCTableA table of all p2p/p2mp/multicast VC entries. SEQUENCE OF JnxAtmVCEntry .1.3.6.1.4.1.2636.3.10.2 |
jnxAtmVCEntrySpecial Cases:
- No traffic Stats for multicast VCs. (0 by default).
- Multipoint Destination IP Address for a p2p vc is
invalid (0.0.0.0 by default).
- When the encapsulation type for the logical interface
(to which VC belongs) is 'atmCccCellRelay', only
Generic VC Info is valid.
- If OAM is disabled (indicated in jnxAtmVCFlags),
then all the OAM config & F5 stats info is invalid.
(zeroed by default). JnxAtmVCEntry .1.3.6.1.4.1.2636.3.10.2.1 |
jnxAtmVCConnTypeThe type of connection. The type 'other' means vc type is unknown
or is not one of the other types.ro Enumeration .1.3.6.1.4.1.2636.3.10.2.1.1 |
jnxAtmVCEncapsulationThe atm encapsulation type associated with the VC.
atmCccCellRelay : ATM Cell Relay for CCC
atmCccVcMux : ATM VC for CCC
atmCiscoNlpid : Cisco-compatible ATM NLPID encapsulation
atmNlpid : ATM NLPID encapsulation
atmSnap : ATM LLC/SNAP encapsulation
atmVcMux : ATM VC multiplexing
atmTccVcMux : TCC (Translational Cross Connection)
over ATM VC MUX encapsulation
atmTccSnap : TCC (Translational Cross Connection)
over ATM LLC/SNAP encapsulationro Enumeration .1.3.6.1.4.1.2636.3.10.2.1.2 |
jnxAtmVCMpDestIPv4AddrThis object is meaningful only if jnxAtmVCConnType value is
'p2mp' (point-to-multipoint). For a p2mp VC, it's the multipoint
destination IPv4 address. When the VC connection type is other
than p2mp OR when the multipoint destination address type is of
IPv6, this object returns 0.0.0.0 by default.ro InetAddressIPv4 (INET-ADDRESS-MIB) .1.3.6.1.4.1.2636.3.10.2.1.3 |
jnxAtmVCMpDestIPv6AddrThis object is meaningful only if jnxAtmVCConnType value is
'p2mp' (point-to-multipoint). For a p2mp VC, it's the multipoint
destination IPv6 address. When the VC connection type is other
than p2mp OR when the multipoint destination address type is of
IPv4, this object returns all the bytes of addr filled with 0.ro InetAddressIPv6 (INET-ADDRESS-MIB) .1.3.6.1.4.1.2636.3.10.2.1.4 |
jnxAtmVCFlagsFlags related to the VC.ro JnxAtmFlags .1.3.6.1.4.1.2636.3.10.2.1.5 |
jnxAtmVCTotalDownTimeThe total VC down time in seconds ever since the system rebooted.ro Integer32 .1.3.6.1.4.1.2636.3.10.2.1.6 |
jnxAtmVCInBytesThe number of bytes received on the VC.ro Counter64 .1.3.6.1.4.1.2636.3.10.2.1.7 |
jnxAtmVCOutBytesThe number of bytes sent out on the VC.ro Counter64 .1.3.6.1.4.1.2636.3.10.2.1.8 |
jnxAtmVCInPktsThe number of packets received on the VC.ro Counter64 .1.3.6.1.4.1.2636.3.10.2.1.9 |
jnxAtmVCOutPktsThe number of packets sent out on the VC.ro Counter64 .1.3.6.1.4.1.2636.3.10.2.1.10 |
jnxAtmVCTailQueuePktDropsThe number of packets dropped due to bandwidth constraints.
Indicates that packets were queued to send out at a rate faster
than allowed.ro Counter64 .1.3.6.1.4.1.2636.3.10.2.1.11 |
jnxAtmVCOAMPeriodThis time interval indicates how often the F5 cells are sent to
know the status of the VC.ro Integer32 .1.3.6.1.4.1.2636.3.10.2.1.12 |
jnxAtmVCOAMUpCellCountThe minimum number of loopback cells to be received to declare
that the VC is up.ro Integer32 .1.3.6.1.4.1.2636.3.10.2.1.13 |
jnxAtmVCOAMDownCellCountThe minimum number of loopback cells to be received to declare
that the VC is down. This object would have zero value if OAM is
not enabled. (indicated in jnxAtmVCFlags)ro Integer32 .1.3.6.1.4.1.2636.3.10.2.1.14 |
jnxAtmVCInOAMF5LoopCellsThe number of OAM F5 loopback cells received. This object would
have zero value if OAM (as indicated in jnxAtmVCFlags) is not
enabled.ro Counter32 .1.3.6.1.4.1.2636.3.10.2.1.15 |
jnxAtmVCOutOAMF5LoopCellsThe number of OAM F5 loopback cells sent. This object would have
zero value if OAM (as indicated in jnxAtmVCFlags) is not
enabled.ro Counter32 .1.3.6.1.4.1.2636.3.10.2.1.16 |
jnxAtmVCInOAMF5RDICellsThe number of OAM F5 cells received, with RDI(Remote Defect
Indication) bit set. This object would have zero value if OAM
(as indicated in jnxAtmVCFlags) is not enabled.ro Counter32 .1.3.6.1.4.1.2636.3.10.2.1.17 |
jnxAtmVCOutOAMF5RDICellsThe number of OAM F5 cells transmitted, with RDI(Remote Defect
Indication) bit set. This object would have zero value if OAM
(as indicated in jnxAtmVCFlags) is not enabled.ro Counter32 .1.3.6.1.4.1.2636.3.10.2.1.18 |
jnxAtmVCInOAMF5AISCellsThe number of OAM F5 cells received, with AIS(Alarm Indication
Signal) bit set. This object would have zero value if OAM (as
indicated in jnxAtmVCFlags) is not enabled.ro Counter32 .1.3.6.1.4.1.2636.3.10.2.1.19 |
jnxAtmVCOutOAMF5AISCellsThe number of OAM F5 cells transmitted, with AIS (Alarm
Indication Signal) bit set. This object would have zero
value if OAM (as indicated in jnxAtmVCFlags) is not
enabled.ro Counter32 .1.3.6.1.4.1.2636.3.10.2.1.20 |
jnxAtmVpTableThe table of ATM VPs. This table augments atmVplTable
defined in standard ATM mib. SEQUENCE OF JnxAtmVpEntry .1.3.6.1.4.1.2636.3.10.3 |
jnxAtmVpEntryEach entry represents config, status and statistics info related
to an ATM VP configured. This entry augments the atmVplEntry
defined in standard ATM mib (RFC 2515). So ifIndex and VPI are the
indices to this table.
Caveats:
- Traffic stats are available per VP tunnel, only if shaping is
configured on the VP. Object 'jnxAtmVpFlags' can be used to
determine if shaping is enabled.
- When no OAM is configured, OAM config and OAM stat objects'
values are invalid (zero by default). Object 'jnxAtmVpFlags'
contains info on whether OAM is configured or not.
- For atm-1 VPs, the only valid object is jnxAtmVpFlags. JnxAtmVpEntry .1.3.6.1.4.1.2636.3.10.3.1 |
jnxAtmVpFlagsThe flags associated with this VP.ro Bits .1.3.6.1.4.1.2636.3.10.3.1.1 |
jnxAtmVpTotalDownTimeThe total VP downtime in seconds, ever since the system rebooted.ro Integer32 .1.3.6.1.4.1.2636.3.10.3.1.2 |
jnxAtmVpOamPeriodThis time interval indicates how often the OAM F4 cells are sent
to determine the status of the VP. The value of this object is zero
when OAM is not enabled on the VP. Object 'jnxAtmVpFlags' can be used
to determine if OAM is enabled.ro Integer32 .1.3.6.1.4.1.2636.3.10.3.1.3 |
jnxAtmVpOamUpCellCountThe minimum number of consecutive loopback cells to be received to
declare that the VP is up. The value of this object is zero when
OAM is not enabled on the VP. Object 'jnxAtmVpFlags' can be used to
determine if OAM is enabled.ro Integer32 .1.3.6.1.4.1.2636.3.10.3.1.4 |
jnxAtmVpOamDownCellCountThe minimum number of consecutive loopback cells to be received to
declare that the VP is down. The value of this object is zero when
OAM is not enabled on the VP. Object 'jnxAtmVpFlags' can be used to
determine if OAM is enabled.ro Integer32 .1.3.6.1.4.1.2636.3.10.3.1.5 |
jnxAtmVpInBytesThe number of bytes received on the VP.ro Counter64 .1.3.6.1.4.1.2636.3.10.3.1.6 |
jnxAtmVpOutBytesThe number of bytes sent out on the VP.ro Counter64 .1.3.6.1.4.1.2636.3.10.3.1.7 |
jnxAtmVpInPktsThe number of packets received on the VP.ro Counter64 .1.3.6.1.4.1.2636.3.10.3.1.8 |
jnxAtmVpOutPktsThe number of packets sent out on the VP.ro Counter64 .1.3.6.1.4.1.2636.3.10.3.1.9 |
jnxAtmVpInOamF4CellsThe number of OAM F4 cells received on the VP.ro Counter32 .1.3.6.1.4.1.2636.3.10.3.1.10 |
jnxAtmVpOutOamF4CellsThe number of OAM F4 cells transmitted on the VP.ro Counter32 .1.3.6.1.4.1.2636.3.10.3.1.11 |
jnxAtmVpInOamF4LoopCellsThe number of OAM F4 loopback cells received on the VP.ro Counter32 .1.3.6.1.4.1.2636.3.10.3.1.12 |
jnxAtmVpOutOamF4LoopCellsThe number of OAM F4 cells transmitted on the VP.ro Counter32 .1.3.6.1.4.1.2636.3.10.3.1.13 |
jnxAtmVpInOamF4RdiCellsThe number of OAM F4 RDI cells received on the VP.ro Counter32 .1.3.6.1.4.1.2636.3.10.3.1.14 |
jnxAtmVpOutOamF4RdiCellsThe number of OAM F4 RDI cells transmitted on the VP.ro Counter32 .1.3.6.1.4.1.2636.3.10.3.1.15 |
jnxAtmVpInOamF4AisCellsThe number of OAM F4 AIS cells received on the VP.ro Counter32 .1.3.6.1.4.1.2636.3.10.3.1.16 |
jnxAtmTrunkTableA table of all ATM Trunk entries. SEQUENCE OF JnxAtmTrunkEntry .1.3.6.1.4.1.2636.3.10.4 |
jnxAtmTrunkEntrySpecial Cases:
- When the encapsulation type for the logical interface
(to which Trunk belongs) is 'atmCccCellRelay', only
Generic Trunk Info is valid. JnxAtmTrunkEntry .1.3.6.1.4.1.2636.3.10.4.1 |
jnxAtmTrunkIdThe identifier for this ATM Trunk.ro Integer32 .1.3.6.1.4.1.2636.3.10.4.1.1 |
jnxAtmTrunkConnTypeThe type of connection. The type 'other' means trunk type is
unknown or is not one of the other types.ro Enumeration .1.3.6.1.4.1.2636.3.10.4.1.2 |
jnxAtmTrunkEncapsulationThe atm encapsulation type associated with the VC or Trunk.
atmCccCellRelay : ATM Cell Relay for CCCro Enumeration .1.3.6.1.4.1.2636.3.10.4.1.3 |
jnxAtmTrunkFlagsFlags related to the Trunk.ro JnxAtmFlags .1.3.6.1.4.1.2636.3.10.4.1.4 |
jnxAtmTrunkTotalDownTimeThe total Trunk down time in seconds ever since the system rebooted.ro Integer32 .1.3.6.1.4.1.2636.3.10.4.1.5 |
jnxAtmTrunkInBytesThe number of bytes received on the Trunk.ro Counter64 .1.3.6.1.4.1.2636.3.10.4.1.6 |
jnxAtmTrunkOutBytesThe number of bytes sent out on the Trunk.ro Counter64 .1.3.6.1.4.1.2636.3.10.4.1.7 |
jnxAtmTrunkInPktsThe number of packets received on the Trunk.ro Counter64 .1.3.6.1.4.1.2636.3.10.4.1.8 |
jnxAtmTrunkOutPktsThe number of packets sent out on the Trunk.ro Counter64 .1.3.6.1.4.1.2636.3.10.4.1.9 |
jnxAtmTrunkTailQueuePktDropsThe number of packets dropped due to bandwidth constraints.
Indicates that packets were queued to send out at a rate faster
than allowed.ro Counter64 .1.3.6.1.4.1.2636.3.10.4.1.10 |
jnxAtmTrunkInOAMF4AISCellsThe number of OAM F4 cells received, with AIS(Alarm Indication
Signal) bit set.ro Counter32 .1.3.6.1.4.1.2636.3.10.4.1.15 |
jnxAtmTrunkOutOAMF4AISCellsThe number of OAM F4 cells sent, with AIS(Alarm Indication
Signal) bit set.ro Counter32 .1.3.6.1.4.1.2636.3.10.4.1.16 |