JUNIPER-ALARM-MIB
Updated Jul 18, 2003The JUNIPER-ALARM-MIB enables SNMP-based monitoring of hardware and software fault conditions on Juniper Networks router chassis, specifically exposing alarm states, severity levels, and event timestamps for system components. This module facilitates the automated detection and correlation of critical infrastructure failures, such as power supply faults, fan failures, and interface errors, within the network management system.
Imported Objects
Objects
11 total| Object Name |
|---|
jnxAlarmsThis is Juniper Networks' implementation of enterprise
specific MIB for alarms from the router chassis box. MODULE-IDENTITY .1.3.6.1.4.1.2636.3.4 |
jnxCraftAlarms OBJECT IDENTIFIER .1.3.6.1.4.1.2636.3.4.2 |
jnxAlarmRelayModeThe alarm relay mode of the craft interface
panel for both yellow and red alarms.
Both yellow and red alarms could be cut off
by a front panel Alarm Cutoff / Lamp Test
(ACO/LT) button.
In the pass-on mode, the alarm relay will be
activated to pass on the yellow or red alarms.
In the cut-off mode, both yellow and red alarms
will be cut off from the alarm relays which are
normally connected to audible sirens or visual
flashing devices.ro Enumeration .1.3.6.1.4.1.2636.3.4.2.1 |
jnxYellowAlarms OBJECT IDENTIFIER .1.3.6.1.4.1.2636.3.4.2.2 |
jnxYellowAlarmStateThe yellow alarm state on the craft interface
panel.
The yellow alarm is on when there is some
system warning such as maintenance alert or
significant temperature increase.
This yellow alarm state could be turned off
by the ACO/LT (Alarm Cut Off / Lamp Test) button
on the front panel module.ro Enumeration .1.3.6.1.4.1.2636.3.4.2.2.1 |
jnxYellowAlarmCountThe number of currently active and non-silent
yellow alarms.
This object is independent of the ACO/LT (Alarm
Cut Off / Lamp Test) button.ro Gauge32 .1.3.6.1.4.1.2636.3.4.2.2.2 |
jnxYellowAlarmLastChangeThe value of sysUpTime when the yellow alarm
last changed - either from off to on or vice
versa. Zero if unknown or never changed since
the agent was up.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.2636.3.4.2.2.3 |
jnxRedAlarms OBJECT IDENTIFIER .1.3.6.1.4.1.2636.3.4.2.3 |
jnxRedAlarmStateThe red alarm indication on the craft interface
panel.
The red alarm is on when there is some system
failure or power supply failure or the system
is experiencing a hardware malfunction or some
threshold is being exceeded.
This red alarm state could be turned off by the
ACO/LT (Alarm Cut Off / Lamp Test) button on the
front panel module.ro Enumeration .1.3.6.1.4.1.2636.3.4.2.3.1 |
jnxRedAlarmCountThe number of currently active and non-silent
red alarms.
This object is independent of the ACO/LT (Alarm
Cut Off / Lamp Test) button.ro Gauge32 .1.3.6.1.4.1.2636.3.4.2.3.2 |
jnxRedAlarmLastChangeThe value of sysUpTime when the red alarm
last changed - either from off to on or vice
versa. Zero if unknown or never changed since
the agent was up.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.2636.3.4.2.3.3 |
More MIBs from Juniper Networks
Browse all Juniper NetworksMIBs →The JUNIPER-CHASSIS-DEFINES-MIB establishes the foundational Object Identifier (OID) namespace and data type definitions required to map and identify specific Juniper chassis hardware platforms and their internal physical components. This module serves as the structural prerequisite for the JUNIPER-CHASSIS-MIB, enabling the retrieval of inventory data, component status, and hardware topology details for Juniper MX, PTX, and EX series devices.
The JUNIPER-MOBILE-GATEWAY-GTP-MIB provides SNMP objects for monitoring GTP (GPRS Tunneling Protocol) session states, tunnel endpoints, and protocol counters on Juniper mobile gateway platforms. It enables administrators to track GTP-C and GTP-U traffic statistics, error conditions, and active tunnel metrics essential for validating mobile core network connectivity.
SNMP MIB module
SNMP MIB module
The JUNIPER-MOBILE-GATEWAY-SGW-GTP-MIB module enables monitoring of GTP (GPRS Tunneling Protocol) session states and traffic counters on Juniper Mobile Gateway Serving Gateways (SGW). It provides specific objects for tracking GTP-C and GTP-U tunnel establishment, teardown, and packet throughput metrics essential for validating mobile core network connectivity.
The JUNIPER-IPSEC-FLOW-MON-MIB monitors Juniper Networks IPsec VPN infrastructure by exposing tables for IKE tunnels, IPSec tunnels, and IPSec security associations to track tunnel states, association parameters, and flow statistics. This module facilitates the management of IPsec security policies and the operational status of encrypted traffic flows within the device's security architecture.