Intel-6000-Switch-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
295
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
295 total| Object Name |
|---|
igmpSnoopingDataPortGroupAll
Ip
::= { igmpSnoopingDataPortEntry 3 }
igmpSnoopingDataPortIpAddr OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-only
STATUS mandatory
DESCRIPTIONro Enumeration .igmpSnoopingControlPortEntry.3 |
igmpSnoopingControlPortRowStatusUsed to control creation and deletion of rows.rw RowStatus (SNMPv2-TC) .igmpSnoopingControlPortEntry.4 |
intel6000Switch OBJECT IDENTIFIER .switch-products.1 |
Intel-Common-MIB Unknown .switch-products.1 |
express6000 OBJECT IDENTIFIER .switch-products.1.1 |
switchMIB OBJECT IDENTIFIER .switch-products.1.2 |
carrierCPSlotChangeEventThe master CP board has changed
from slotA to slotB or vice-versa. TRAP-TYPE .switch-products.1.2.0.1 |
carrierStatusAChangeEventThe status (inserted/running) of the
CP in slot A has changed. TRAP-TYPE .switch-products.1.2.0.2 |
carrierStatusBChangeEventThe status (inserted/running) of the
CP in slot B has changed. TRAP-TYPE .switch-products.1.2.0.3 |
mediaCardChangeEventOne or more of the media cards has been
inserted or removed. TRAP-TYPE .switch-products.1.2.0.4 |
fanFailEventOne or more the fans has failed. TRAP-TYPE .switch-products.1.2.0.5 |
powerSupplyFailEventOne or more of the power supplies
has failed. TRAP-TYPE .switch-products.1.2.0.6 |
highTemperatureEventThe temperature has exceeded the
high temperature mark; the switch
is shutting down immediately. TRAP-TYPE .switch-products.1.2.0.7 |
risingTemperatureEventThe temperature of the switch is
rising. If the temperature continues
to rise, the switch will shut down. TRAP-TYPE .switch-products.1.2.0.8 |
fallingTemperatureEventThe temperature of the switch was
dangerously high, but now the
temperature has fallen back into the
normal operating range. TRAP-TYPE .switch-products.1.2.0.9 |
stormBcastControlDiscardEventThe broadcast framerate
on this port has exceeded the threshold
level set by the user. The storm control
software has put this port into frame discard
mode. TRAP-TYPE .switch-products.1.2.0.10 |
stormMcastControlDiscardEventThe multicast framerate
on this port has exceeded the threshold
level set by the user. The storm control
software has put this port into frame discard
mode. TRAP-TYPE .switch-products.1.2.0.11 |
switchConfigGroup OBJECT IDENTIFIER .switch-products.1.2.1 |
ipAddressIP address for the management
port of this entity.rw IpAddress .switch-products.1.2.1.1 |
netMaskThe netmask for the management
port of this entity.rw IpAddress .switch-products.1.2.1.2 |
defaultGatewayThe IP address of the Default
Gateway for this entity.rw IpAddress .switch-products.1.2.1.3 |
broadcastAddressThe broadcast address for the
management port of this entity.rw IpAddress .switch-products.1.2.1.4 |
maxMacAddressesLargest aggregate number of MAC addresses which
this entity can support simultaneously.ro INTEGER .switch-products.1.2.1.5 |
clearStatisticsSetting this variable to TRUE (1) clears the
traffic statistics accumulators on this entity.
Setting this variable to any other value has
no effect. The variable always returns 0 when
read.rw INTEGER .switch-products.1.2.1.6 |
ageFilterDatabaseSetting this variable to FALSE (0) causes this
entity to stop aging out entries from its filter
database. Setting this variable to TRUE (1)
causes this entity to age out filter database
entries as defined in IEEE 802.1D. Whenever
this entity restarts, this variable keeps
previously assigned value.rw INTEGER .switch-products.1.2.1.7 |
entMibVersionThe revision level of the MIB contained in the
CP firmware.ro DisplayString (SNMPv2-TC) .switch-products.1.2.1.8 |
telnetEnableThe current state of the telnet daemon in the
Switch. If this field is set to disable,
external accesses via telnet will not be permitted.rw Enumeration .switch-products.1.2.1.9 |
syslogEnableThe current state of remote IP system logging. If
enabled, the Switch will log messages to the
SyslogIp IP address. If it is disabled, it will log
messages to the console only.rw Enumeration .switch-products.1.2.1.10 |
syslogIpThe Ip address for remote IP system logging. If
syslogEnabled is enabled, the Switch log
messages to this IP.rw IpAddress .switch-products.1.2.1.11 |
syslogCmdsIf system logging is enabled, this field enables
or disables the logging of commands issued on a
terminal command line.rw Enumeration .switch-products.1.2.1.12 |
syslogOutIf system logging is enabled, this field enables
or disables the logging of output from the
terminal.rw Enumeration .switch-products.1.2.1.13 |
nvramLoadSaveThis field triggers loading and saving of the
system settings in non-volatile RAM space. To
trigger a load or a save the NVRAM IP address
must first be set below. This field is always
read as one. The filename used will be the
hexadecimal value of this systems IP address.rw Enumeration .switch-products.1.2.1.14 |
nvramLastOpStatThis field shows the outcome of the last
NVRAM load or save. If the NVRAM update was
sucessful, this field will return one.ro Enumeration .switch-products.1.2.1.15 |
nvramRemoteIpThis is the IP address of the remote tftp machine
where the NVRAM is to be loaded or saved. For
nvramLoadSave to have an effect, this field
must be set to a vaild IP address.rw IpAddress .switch-products.1.2.1.16 |
nvramRemotePathThis is the path on the remote machine where the
NVRAM image is to be retrieved or stored. This
path does not include the filename, and does
not end with a /. This field is optional, and
if left empty, the system will use the default
tftp location.rw DisplayString (SNMPv2-TC) .switch-products.1.2.1.17 |
monitorGroup OBJECT IDENTIFIER .switch-products.1.2.2 |
diagnosticsResultsA result of the most recent diagnostic test for
the whole stack.ro Enumeration .switch-products.1.2.2.1 |
diagnosticsTimeThe date and time of the most recent diagnostic
test for the whole stack.ro DisplayString (SNMPv2-TC) .switch-products.1.2.2.2 |
lastDiagnosticsTestThe number indicating what diagnostic test was
run last. The list represents the power-up diagnostic
test sequence. Normally the returned value should be
the index of the last test in the sequence.ro Enumeration .switch-products.1.2.2.3 |
commGroup OBJECT IDENTIFIER .switch-products.1.2.3 |
commNumCommsThe number of SNMP Communities currently configured in this
system. This number should reflect the number of entries in
the commInfoTable.ro INTEGER .switch-products.1.2.3.1 |
commInfoTableA list of Switch Configuration Community Entries SEQUENCE OF CommInfoEntry .switch-products.1.2.3.2 |
commInfoEntryA list of Community properties for the Switch. CommInfoEntry .switch-products.1.2.3.2.1 |
commInfoIndexAn index that uniquely identifies an entry in the
Switch Community Info Table.rw INTEGER .switch-products.1.2.3.2.1.1 |
commInfoNameThe name of this Switch Community Entry.rw DisplayString (SNMPv2-TC) .switch-products.1.2.3.2.1.2 |
commInfoGetThe GET permission for the community.rw Enumeration .switch-products.1.2.3.2.1.3 |
commInfoSetThe SET permission for the community.rw Enumeration .switch-products.1.2.3.2.1.4 |
commInfoTrapThe TRAP permission for the community.rw Enumeration .switch-products.1.2.3.2.1.5 |
commAltTrapPortAn alternate port to which the agent
will send TRAP notifications. Note
that the agent will continue to send
TRAPs to the SNMP port.
Setting this value to zero disables
sending TRAPs to the alternate port.rw INTEGER (0 | 2000..9000) .switch-products.1.2.3.3 |
commSnmpSecurityLevelSecurity level to be used by the agent
when checking requests.
Level 1 check community string on get and set.
Level 2 check community string on get,
community string and host on set
Level 3 check community string and host on get and set.rw INTEGER .switch-products.1.2.3.4 |
hostGroup OBJECT IDENTIFIER .switch-products.1.2.4 |
hostNumHostsThe current number of SNMP hosts in the system. Each
host is allowed to perform get, set, and trap operations
based on its associated community.ro INTEGER .switch-products.1.2.4.1 |
hostInfoTableA list of Switch Configuration Host Entries SEQUENCE OF HostInfoEntry .switch-products.1.2.4.2 |
hostInfoEntryA list of Host properties for the Switch HostInfoEntry .switch-products.1.2.4.2.1 |
hostInfoIndexAn index that uniquely identifies an entry in the
Switch Host Info Table.rw INTEGER .switch-products.1.2.4.2.1.1 |
hostInfoNameThe name of this Switch Host Entry.rw DisplayString (SNMPv2-TC) .switch-products.1.2.4.2.1.2 |
hostInfoIpThe IP Address for the host.rw IpAddress .switch-products.1.2.4.2.1.3 |
hostInfoCommThe name of the community this host belongs to.rw DisplayString (SNMPv2-TC) .switch-products.1.2.4.2.1.4 |
serialGroup OBJECT IDENTIFIER .switch-products.1.2.5 |
serialBaudRateThe baud rate in bits per second of the RS-232 port.rw Enumeration .switch-products.1.2.5.1 |
modemControlLinesIndicates whether the RS-232 port modem control lines
are enabled.rw Enumeration .switch-products.1.2.5.2 |
spanGroup OBJECT IDENTIFIER .switch-products.1.2.9 |
spanOnOffTurns Spanning Tree ON/OFF for the switch.rw Enumeration .switch-products.1.2.9.1 |
spanTypeType of spanning tree.rw Enumeration .switch-products.1.2.9.2 |
spanResetDefaultsReset all settable spanning tree parameters to defaults.rw Enumeration .switch-products.1.2.9.4 |
spanRapidWhen spanType is STP, turns Spanning Tree
Rapid Reconfiguration ON/OFF.rw Enumeration .switch-products.1.2.9.5 |
spanPortTableTable containing per-port status
for single spanning tree. SEQUENCE OF SpanPortEntry .switch-products.1.2.9.6 |
spanPortEntryPer-port status
for single spanning tree. SpanPortEntry .switch-products.1.2.9.6.1 |
spanPortPortThe port number on the switch.ro PortNumber .switch-products.1.2.9.6.1.1 |
spanPortQuickStatusThe current status, enabled or disabled,
of Port Quick for this port.rw EnableStatus .switch-products.1.2.9.6.1.2 |
spanPortAutoPath cost is either Fixed or Auto. If
Auto, cost is calculated automatically,
and depends on media data rates and
link aggregation.ro Enumeration .switch-products.1.2.9.6.1.3 |
fanGroup OBJECT IDENTIFIER .switch-products.1.2.10 |
fanNumFansThe total number of fans possible in this chassis. A fan
need not be present to count.ro INTEGER .switch-products.1.2.10.1 |
fanInfoTableA list of Fan States SEQUENCE OF FanInfoEntry .switch-products.1.2.10.2 |
fanInfoEntryA list of Fan properties for the Switch FanInfoEntry .switch-products.1.2.10.2.1 |
fanIndexAn index that uniquely identifies an entry in the
Switch Fan Table.ro INTEGER .switch-products.1.2.10.2.1.1 |
fanStatusStates operational status of Fan.rw Enumeration .switch-products.1.2.10.2.1.2 |
psGroup OBJECT IDENTIFIER .switch-products.1.2.11 |
psNumberThe number of power supplies this chassis is capable of
holding. A power supply need not be present to count.ro INTEGER .switch-products.1.2.11.1 |
psInfoTableA list of Power Supply States SEQUENCE OF PsInfoEntry .switch-products.1.2.11.2 |
psInfoEntryA list of Power Supply properties for the Switch PsInfoEntry .switch-products.1.2.11.2.1 |
psIndexAn index that uniquely identifies an entry in the
Switch Power Supply Table.ro Enumeration .switch-products.1.2.11.2.1.1 |
psPresentStates presence of Power Supply.ro Enumeration .switch-products.1.2.11.2.1.2 |
psStatusStates operational status of Power Supply.ro Enumeration .switch-products.1.2.11.2.1.3 |
tempGroup OBJECT IDENTIFIER .switch-products.1.2.13 |
tempCurrentThe current temperature of the switch in degrees
centigrade.ro INTEGER .switch-products.1.2.13.1 |
tempAlarmThe status of the temperature alarm. This alarm is
on if the current temperature exceeds the high water mark.ro Enumeration .switch-products.1.2.13.2 |
tempHighestThe highest temperature reached after the temperature alarm.
If the alarm is not active, the value is zero.ro INTEGER .switch-products.1.2.13.3 |
tempHighThe high water mark for the temperature. If this temperature
is exceeded, the temperature alarm is activated.rw INTEGER .switch-products.1.2.13.4 |
tempLowThe low water mark for the temperature. If the temperature
falls below the low water mark, the temperature alarm will
be reset.rw INTEGER .switch-products.1.2.13.5 |
gigabitGroup OBJECT IDENTIFIER .switch-products.1.2.14 |
gigabitPortTableThis table contains the per port gigabit configurables.
The indexes reference a gigabit slot, and the ports numbered
from one from the left most port. SEQUENCE OF GigabitPortTableEntry .switch-products.1.2.14.2 |
gigabitPortTableEntryA list of gigabit configurables for the switch GigabitPortTableEntry .switch-products.1.2.14.2.1 |
gigabitPortTableSlotThe slot in which this gigabit card resides. This
slot should be the same as one of the valid gigabit
slots in the slot table of this MIB.ro INTEGER .switch-products.1.2.14.2.1.1 |
gigabitPortTablePortThe number of the gigabit port on the card. These
ports specify an individual port on a gigabit switch
or a gigabit repeater. A port here does not represent
a unique interface in the interfaces table.ro INTEGER .switch-products.1.2.14.2.1.2 |
gigabitPortTableLinkStateThis field shows the current link state of the
gigabit sub-port.ro Enumeration .switch-products.1.2.14.2.1.4 |
gigabitPortTablePortAutoNegThe current ability of this port to participate in
autonegotiation.rw Enumeration .switch-products.1.2.14.2.1.5 |
tenHundredGroup OBJECT IDENTIFIER .switch-products.1.2.15 |
tenHundredPortTableThis table contains the per port information
for the 10/100 Ethernet boards in the system.
This table will be indexed by slot and port. SEQUENCE OF TenHundredPortTableEntry .switch-products.1.2.15.1 |
tenHundredPortTableEntryA list of 10/100 Ethernet configurables for
the switch. TenHundredPortTableEntry .switch-products.1.2.15.1.1 |
tenHundredPortTableSlotThe slot in which this 10/100 card resides. This
slot should be the same as one of the valid 10/100
slots in the slot table of this MIB.ro INTEGER .switch-products.1.2.15.1.1.1 |
tenHundredPortTablePortThe number of the 10/100 port on the system. A port
here represents a unique interface in the the interfaces
table.ro INTEGER .switch-products.1.2.15.1.1.2 |
tenHundredPortTableLinkStateThis field shows the current link state of the
10/100 port.ro Enumeration .switch-products.1.2.15.1.1.3 |
tenHundredPortTableConfigThe autonegotiate mode, speed, and duplex mode
for this port.
If link state is UP, then this object represents
the settings for the active connect.
If link state is DOWN, then this ojbect represents
the connection mode(s) that this port will accept.rw Enumeration .switch-products.1.2.15.1.1.4 |
vlanGroup OBJECT IDENTIFIER .switch-products.1.2.16 |
vlanValidThis field displays if the current VLAN configuration
in the Switch is valid.ro Enumeration .switch-products.1.2.16.1 |
vlanConfigTableThis table contains the virtual lan configuration
parameters for each virtual lan configured in the
system. SEQUENCE OF VlanConfigEntry .switch-products.1.2.16.2 |
vlanConfigEntryAn entry containing information about the Virtual
Lan configuration. VlanConfigEntry .switch-products.1.2.16.2.1 |
vlanConfigVIDThe Virtual Lan Id number.ro VlanId .switch-products.1.2.16.2.1.1 |
vlanConfigNameThe name associated with this virtual lan ID.rw DisplayString (SNMPv2-TC) .switch-products.1.2.16.2.1.2 |
vlanConfigIpAddrThe IP address associated with this virtual lan.rw IpAddress .switch-products.1.2.16.2.1.3 |
vlanConfigNetmaskThe netmask associated with this virtual lan.rw IpAddress .switch-products.1.2.16.2.1.4 |
vlanConfigBroadcastThe broadcast address associated with this virtual lan.rw IpAddress .switch-products.1.2.16.2.1.5 |
vlanConfigRoutingEnable or disable routing on a per-vlan
basis.rw EnableStatus .switch-products.1.2.16.2.1.6 |
vlanResetReset VLAN configuration to factory
defaults.rw Enumeration .switch-products.1.2.16.3 |
vlanPortTableThis table contains the virtual lan configuration
parameters which are configured on a per-port
basis. SEQUENCE OF VlanPortEntry .switch-products.1.2.16.4 |
vlanPortEntryAn entry containing the virtual lan configuration
parameters which are configured on a per-port
basis. VlanPortEntry .switch-products.1.2.16.4.1 |
vlanPortNumberExternal port number.
This number corresponds to the ifTable ifIndex.ro PortNumber .switch-products.1.2.16.4.1.1 |
vlanPortTrustedVidIf VlanPortTrustedVid is 'true', then the VID
of tagged frames is alwasy used, otherwise,
the PVID of the port is used even if the
frame is tagged.rw Boolean .switch-products.1.2.16.4.1.2 |
vlanPortTrustedPriorityIf VlanPortTrustedPriority is 'true', then
the priority of tagged frames is always used,
otherwise, the default port priority is used
even if the frame is tagged.rw Boolean .switch-products.1.2.16.4.1.3 |
routingGroup OBJECT IDENTIFIER .switch-products.1.2.17 |
routingRouterIdA 32-bit integer uniquely identifying the
switch.
By convention, to ensure uniqueness, this
should default to the value of one of the
router's IP interface addresses.
This object cannot be accessed unless GateD is
enabled.rw IpAddress .switch-products.1.2.17.1 |
routingScanIntervalThe number of seconds indicating how often
GateD will check with the kernel for the interface
changes when no notification is received from
the kernel.
This object cannot be accessed unless routing is
enabled.rw INTEGER .switch-products.1.2.17.2 |
routingConfigGroup OBJECT IDENTIFIER .switch-products.1.2.17.3 |
routingEnableEnable/disable routing.
Writing enableInit to this object starts the
GateD process, but does not
enable any routing protocols. enableRestore
starts the GateD process and restores the
GateD configuration from nonvolatile memory.
When read, this object will return either enabled
or disabled.rw Enumeration .switch-products.1.2.17.3.1 |
routingRipConfEnable/disable RIPv2.rw Enumeration .switch-products.1.2.17.3.2 |
routingOspfConfEnable/disable OSPF.rw Enumeration .switch-products.1.2.17.3.3 |
routingPreferencesGroup OBJECT IDENTIFIER .switch-products.1.2.17.4 |
routingOspfPrefThe preference level for OSPF-based routing
This object cannot be accessed unless routing is
enabled.rw INTEGER .switch-products.1.2.17.4.1 |
routingStaticConfigPrefThe preference level for the default static route.
This object cannot be accessed unless routing is
enabled.rw INTEGER .switch-products.1.2.17.4.2 |
routingRipPrefThe preference level for rip-based routing
This object cannot be accessed unless routing is
enabled.rw INTEGER .switch-products.1.2.17.4.3 |
routingOspfAsExtPrefThe preference level for OSPF as extern based routing
This object cannot be accessed unless routing is
enabled.rw INTEGER .switch-products.1.2.17.4.4 |
routingIfPrefTableA list of local interfaces and their preference levels. SEQUENCE OF RoutingIfPrefEntry .switch-products.1.2.17.5 |
routingIfPrefEntryAn interface-preference pair. RoutingIfPrefEntry .switch-products.1.2.17.5.1 |
routingIfPrefAddressThe IP Address of this system on the indicated
subnet. For unnumbered interfaces, the value 0.0.0.N,
where the least significant 24 bits (N) is the ifIndex
for the IP Interface in network byte order.ro IpAddress .switch-products.1.2.17.5.1.1 |
routingIfPrefThe preference level for this interfacerw INTEGER .switch-products.1.2.17.5.1.2 |
staticRouteNumberThe number of current staticRouteTable entries
that are not invalid.ro Gauge .switch-products.1.2.17.6 |
staticRouteTableThis entity's static IP routing config table. SEQUENCE OF StaticRouteEntry .switch-products.1.2.17.7 |
staticRouteEntryA particular static route to a particular
destination. StaticRouteEntry .switch-products.1.2.17.7.1 |
staticRouteDestThe destination IP address of this route.
This object may not take a Multicast (Class D)
address value.
Any assignment (implicit or otherwise) of an
instance of this object to a value x must be
rejected if the bitwise logical-AND of x with
the value of the corresponding instance of the
staticRouteMask object is not equal to x.ro IpAddress .switch-products.1.2.17.7.1.1 |
staticRouteMaskIndicate the mask to be logical-ANDed with the
destination address before being compared to
the value in the staticRouteDest field. For
those systems that do not support arbitrary
subnet masks, an agent constructs the value of
the staticRouteMask by reference to the IP
Address Class.
Any assignment (implicit or otherwise) of an
instance of this object to a value x must be
rejected if the bitwise logical-AND of x with
the value of the corresponding instance of the
staticRouteDest object is not equal to
staticRouteDest.ro IpAddress .switch-products.1.2.17.7.1.2 |
staticRouteNextHopOn remote routes, the address of the next sys-
tem en route; Otherwise, 0.0.0.0.ro IpAddress .switch-products.1.2.17.7.1.3 |
staticRouteIfThe local interface through which the
next hop of this route should be reached.rw IpAddress .switch-products.1.2.17.7.1.4 |
staticRoutePrefThe preference value for this route.
Default value is 20 for the default
route, 60 otherwise.rw INTEGER .switch-products.1.2.17.7.1.5 |
staticRouteTypeThe type of route.rw Enumeration .switch-products.1.2.17.7.1.6 |
staticRouteStatusThe row status variable, used according to
row installation and removal conventions.rw INTEGER .switch-products.1.2.17.7.1.7 |
routingSaveConfigWrite to this object to save the current
router configuration to nonvolatile storage.
The agent will perform an activate before
saving.
You cannot save the configuration unless
routing is enabled.rw Enumeration .switch-products.1.2.17.8 |
errorGroup OBJECT IDENTIFIER .switch-products.1.2.18 |
errorTableA list of SNMP User-error Entries. SEQUENCE OF ErrorEntry .switch-products.1.2.18.1 |
errorEntryA description of an SNMP user-error. ErrorEntry .switch-products.1.2.18.1.1 |
errorIndexAn index that uniquely identifies an entry in the
Error Table.ro INTEGER .switch-products.1.2.18.1.1.1 |
errorMsgThe description of the SNMP configuration
error.ro DisplayString (SNMPv2-TC) .switch-products.1.2.18.1.1.2 |
errorOidThe object ID for the SNMP manager request
which caused this error.ro OBJECT IDENTIFIER .switch-products.1.2.18.1.1.3 |
errorTimeThe time, in hundreths of a second since
system boot, that the error occurred.ro TimeTicks (SNMPv2-SMI) .switch-products.1.2.18.1.1.4 |
clearErrorTableWriting true to this object clears
the SNMP Error Table.rw Enumeration .switch-products.1.2.18.2 |
linkStateGroup OBJECT IDENTIFIER .switch-products.1.2.19 |
linkStateTableThis table contains the link states
of every port on the switch, indexed
by slot number and local (per-slot)
port number. SEQUENCE OF LinkStateEntry .switch-products.1.2.19.1 |
linkStateEntryEach entry contains the link state
and last-changed time of a port
on the switch, indexed by slot
number and local port number. LinkStateEntry .switch-products.1.2.19.1.1 |
linkStateSlotThe index of this media card on the
Switch chassis. Media card indices
begin at one, at the top of the chassis.ro INTEGER .switch-products.1.2.19.1.1.1 |
linkStatePortThe index of this port on the
media card. Port indices begin
at one, at the left side of the
card, when viewed from the front.ro INTEGER .switch-products.1.2.19.1.1.2 |
linkStateStateThe current link state of this
port.ro Enumeration .switch-products.1.2.19.1.1.3 |
linkStateTimeThe most recent time, in hundreths of
a second since system boot, that this
port's link state changed.ro TimeTicks (SNMPv2-SMI) .switch-products.1.2.19.1.1.4 |
carrierGroup OBJECT IDENTIFIER .switch-products.1.2.20 |
carrierCPSlotIDIndicates which slot
contains the master CP.ro Enumeration .switch-products.1.2.20.1 |
carrierStatusAIndicates whether CP board A is
inserted, and if inserted,
whether it is running.ro Enumeration .switch-products.1.2.20.2 |
carrierStatusBIndicates whether CP board B is
inserted, and if inserted,
whether it is running.ro Enumeration .switch-products.1.2.20.3 |
moduleGroup OBJECT IDENTIFIER .switch-products.1.2.21 |
moduleTableTable containing hardware and software
configuration information. SEQUENCE OF ModuleEntry .switch-products.1.2.21.1 |
moduleEntryHardware and software configuration data. ModuleEntry .switch-products.1.2.21.1.1 |
moduleSlotNumThe Slot ID of the switch. Slot 1 is physically
the top slot in a chassis.ro INTEGER .switch-products.1.2.21.1.1.1 |
moduleCardThe specific card within a slot.ro Enumeration .switch-products.1.2.21.1.1.2 |
moduleContentThe content-type for this entry.ro Enumeration .switch-products.1.2.21.1.1.3 |
moduleDataValidIndicates whether the version text
is initialized.ro Enumeration .switch-products.1.2.21.1.1.4 |
moduleTextA text string containing hardware or
sofware version information.ro DisplayString (SNMPv2-TC) .switch-products.1.2.21.1.1.5 |
pingGroup OBJECT IDENTIFIER .switch-products.1.2.22 |
pingHostAddressThe hostname or host IP address for
the PING.rw DisplayString (SNMPv2-TC) .switch-products.1.2.22.1 |
pingRequestWriting any value to this object sends
a PING.rw INTEGER .switch-products.1.2.22.2 |
pingTimePING roundtrip time in milliseconds.ro INTEGER .switch-products.1.2.22.3 |
pingStatusStatus of most recent ping request.ro Enumeration .switch-products.1.2.22.4 |
dnsGroup OBJECT IDENTIFIER .switch-products.1.2.23 |
dnsEnableThe current state of the Domain Name Server in the
Switch. If this field is set to enable,
Domain Name Services will be supported.rw Enumeration .switch-products.1.2.23.1 |
dnsDomainNameThe Domain Name for the network this
switch is on.rw DisplayString (SNMPv2-TC) .switch-products.1.2.23.2 |
dnsPrimaryServerThe primary DNS server for the network this
switch is on.rw DisplayString (SNMPv2-TC) .switch-products.1.2.23.3 |
dnsBackupServerThe secondary DNS server for the network this
switch is on.rw DisplayString (SNMPv2-TC) .switch-products.1.2.23.4 |
stormControlGroup OBJECT IDENTIFIER .switch-products.1.2.24 |
stormBcastControlTableTable containing configuration and status
information for broadcast storm control. SEQUENCE OF StormBcastControlEntry .switch-products.1.2.24.1 |
stormBcastControlEntryConfiguration and status for broadcast storm
control. StormBcastControlEntry .switch-products.1.2.24.1.1 |
stormBcastControlPortThe port number on the switch,
equivalent to ifIndex.ro INTEGER .switch-products.1.2.24.1.1.1 |
stormBcastControlThresholdThe broadcast frame rate, in percent of total bandwidth,
at which discarding is triggered for this port.rw INTEGER .switch-products.1.2.24.1.1.2 |
stormBcastControlDiscardPeriodThe amount of time, in seconds, that
discarding will continue on this port
once triggered. If the discard period
is set to zero seconds and the port
transitions to discarding state, then user
intervention is required to remove the port
from discarding state.rw INTEGER .switch-products.1.2.24.1.1.3 |
stormBcastControlRateThe current broadcast rate, measured
as a precentage of total bandwidth,
for this port.ro INTEGER .switch-products.1.2.24.1.1.4 |
stormBcastControlDisablesThe number of times this port entered the
discard state as a result of storm control.ro INTEGER .switch-products.1.2.24.1.1.5 |
stormBcastControlEnablesThe number of times this port exited the
discard state as a result of storm control.ro INTEGER .switch-products.1.2.24.1.1.6 |
stormBcastControlTimeLeftThe number of seconds remaining until
this port will exit the discard state.ro INTEGER .switch-products.1.2.24.1.1.7 |
stormBcastControlStatusThe current status of this port with respect
to storm control. If the port is in the
discarding state, then writing 'exitDiscardState'
to stormBcastControlStatus will cause the
port to exit the discarding state. No other value
may be written to this object.rw Enumeration .switch-products.1.2.24.1.1.8 |
stormMcastControlTableTable containing configuration and status
information for multicast storm control. SEQUENCE OF StormMcastControlEntry .switch-products.1.2.24.2 |
stormMcastControlEntryConfiguration and status for multicast storm
control. StormMcastControlEntry .switch-products.1.2.24.2.1 |
stormMcastControlPortThe port number on the switch,
equivalent to ifIndex.ro INTEGER .switch-products.1.2.24.2.1.1 |
stormMcastControlThresholdThe multicast frame rate, in percent of total bandwidth,
at which discarding is triggered for this port.rw INTEGER .switch-products.1.2.24.2.1.2 |
stormMcastControlDiscardPeriodThe amount of time, in seconds, that
discarding will continue on this port
once triggered. If the discard period
is set to zero seconds and the port
transitions to discarding state, then user
intervention is required to remove the port
from discarding state.rw INTEGER .switch-products.1.2.24.2.1.3 |
stormMcastControlRateThe current multicast rate, measured
as a precentage of total bandwidth,
for this port.ro INTEGER .switch-products.1.2.24.2.1.4 |
stormMcastControlDisablesThe number of times this port entered the
discard state as a result of storm control.ro INTEGER .switch-products.1.2.24.2.1.5 |
stormMcastControlEnablesThe number of times this port exited the
discard state as a result of storm control.ro INTEGER .switch-products.1.2.24.2.1.6 |
stormMcastControlTimeLeftThe number of seconds remaining until
this port will exit the discard state.ro INTEGER .switch-products.1.2.24.2.1.7 |
stormMcastControlStatusThe current status of this port with respect
to storm control. If the port is in the
discarding state, then writing 'exitDiscardState'
to stormMcastControlStatus will cause the
port to exit the discarding state. No other value
may be written to this object.rw Enumeration .switch-products.1.2.24.2.1.8 |
igmpSnoopingGroup OBJECT IDENTIFIER .switch-products.1.2.25 |
igmpSnoopingEnableEnable or disable IGMP snooping for system.rw Enumeration .switch-products.1.2.25.1 |
igmpSnoopingResetControlReset all control ports in the system to NORMAL mode.
Reading always returns other(1),
Writing reset(2) performs the reset.rw Enumeration .switch-products.1.2.25.2 |
igmpSnoopingResetDataReset all data ports in the system to NORMAL mode.
Reading always returns other(1),
Writing reset(2) performs the reset.rw Enumeration .switch-products.1.2.25.3 |
igmpSnoopingAgeTimeSet the snoop aging time.rw TimeInterval .switch-products.1.2.25.4 |
igmpSnoopingVlanResetTable SEQUENCE OF IgmpSnoopingVlanResetEntry .switch-products.1.2.25.5 |
igmpSnoopingVlanResetEntry IgmpSnoopingVlanResetEntry .switch-products.1.2.25.5.1 |
igmpSnoopingVlanResetVlanIdVlan identifier.ro VlanId .switch-products.1.2.25.5.1.1 |
igmpSnoopingVlanResetDataReset all data ports in the vlan to NORMAL mode.
Reading always returns other(1),
Writing reset(2) performs the reset.rw Enumeration .switch-products.1.2.25.5.1.2 |
igmpSnoopingVlanResetControlReset all control ports in the vlan to NORMAL mode.
Reading always returns other(1),
Writing reset(2) performs the reset.rw Enumeration .switch-products.1.2.25.5.1.3 |
igmpSnoopingDataPortTable SEQUENCE OF IgmpSnoopingDataPortEntry .switch-products.1.2.25.6 |
igmpSnoopingDataPortEntry IgmpSnoopingDataPortEntry .switch-products.1.2.25.6.1 |
igmpSnoopingDataPortVlanIdVlan identifier.ro VlanId .switch-products.1.2.25.6.1.1 |
igmpSnoopingDataPortNumberExternal port number.
This number corresponds to the ifTable ifIndex.ro PortNumber .switch-products.1.2.25.6.1.2 |
igmpSnoopingStatusTableTable of entries for reporting IGMP snooping status with Mac address to Port address mapping SEQUENCE OF IgmpSnoopingStatusEntry .switch-products.1.2.25.8 |
igmpSnoopingStatusEntry IgmpSnoopingStatusEntry .switch-products.1.2.25.8.1 |
igmpSnoopingVlanIdVlan identifier.ro VlanId .switch-products.1.2.25.8.1.1 |
igmpSnoopingMcastMacAddrMulticast mac address.ro MacAddress (SNMPv2-TC) .switch-products.1.2.25.8.1.2 |
igmpSnoopingPortExternal port number.
This number corresponds to the ifTable ifIndex.ro PortNumber .switch-products.1.2.25.8.1.3 |
igmpSnoopingIpStatusTableTable of entries for reporting IGMP snooping status with Mac address to Ip address mapping SEQUENCE OF IgmpSnoopingIpStatusEntry .switch-products.1.2.25.9 |
igmpSnoopingIpStatusEntry IgmpSnoopingIpStatusEntry .switch-products.1.2.25.9.1 |
igmpSnoopingIpVlanIdVlan identifier.ro VlanId .switch-products.1.2.25.9.1.1 |
igmpSnoopingIpMcastMacAddrMulticast mac address.ro MacAddress (SNMPv2-TC) .switch-products.1.2.25.9.1.2 |
igmpSnoopingIpAddressMulticast IP address.
There can be several of these for each multicast mac address.ro IpAddress .switch-products.1.2.25.9.1.3 |
pvstpGroup OBJECT IDENTIFIER .switch-products.1.2.26 |
pvstpTablePer Vlan Spanning Tree Protocol Table. SEQUENCE OF PvstpEntry .switch-products.1.2.26.1 |
pvstpEntryInformation about an instance of a spanning tree for the
specified vlan. All time (TimeTic, Timeout) values are
in hundreths of a second. PvstpEntry .switch-products.1.2.26.1.1 |
pvstpVlanIdVlan Identifier.ro VlanId .switch-products.1.2.26.1.1.1 |
pvstpProtocolSpecificationWhat spanning tree protocol is being run.
ieee8021w1s1 indicates the version 1.0
implementation of 802.1w and 802.1s.ro Enumeration .switch-products.1.2.26.1.1.2 |
pvstpPriorityThe first 2 octets of the bridge identifier.rw INTEGER .switch-products.1.2.26.1.1.3 |
pvstpTimeSinceTopologyChangeTime since topology change.ro TimeTicks (SNMPv2-SMI) .switch-products.1.2.26.1.1.4 |
pvstpTopChangesNumber of topology changes detected.ro Counter .switch-products.1.2.26.1.1.5 |
pvstpDesignatedRootThe current root of the spanning tree.ro BridgeId .switch-products.1.2.26.1.1.6 |
pvstpRootCostro INTEGER .switch-products.1.2.26.1.1.7 |
pvstpRootPortTotal cost to the root.ro INTEGER .switch-products.1.2.26.1.1.8 |
pvstpMaxAgeTimeout on stp information.ro Timeout .switch-products.1.2.26.1.1.9 |
pvstpHelloTimeConfiguration message interval.ro Timeout .switch-products.1.2.26.1.1.10 |
pvstpHoldTimeMinimum interval between transmition of
configuration messages.ro INTEGER .switch-products.1.2.26.1.1.11 |
pvstpForwardDelayLength of time spent in each state.ro Timeout .switch-products.1.2.26.1.1.12 |
pvstpBridgeMaxAgeValue in hundredths of seconds which
all bridges use for max age
when this bridge is a root. Actual
resolution is one second.rw Timeout .switch-products.1.2.26.1.1.13 |
pvstpBridgeHelloTimeValue to used for hello time when this
bridge is a root.ro Timeout .switch-products.1.2.26.1.1.14 |
pvstpBridgeForwardDelayValue used for forward delay when this
bridge is a root.ro Timeout .switch-products.1.2.26.1.1.15 |
pvstpBridgeRapidWhen spanType is pvstp, turns Spanning Tree
Rapid Reconfiguration ON/OFF for the vlan.rw Enumeration .switch-products.1.2.26.1.1.16 |
pvstpBridgeIdThe Bridge ID in use for this VLAN.ro BridgeId .switch-products.1.2.26.1.1.17 |
pvstpPortTablePer Vlan Spanning Tree Protocol Port Table. SEQUENCE OF PvstpPortEntry .switch-products.1.2.26.2 |
pvstpPortEntryInformation about a specific port for an
instance of a spanning tree for the
specified vlan. All time (TimeTic, Timeout)
values are in hundreths of a second. PvstpPortEntry .switch-products.1.2.26.2.1 |
pvstpPortVlanIdVlan identifier.ro VlanId .switch-products.1.2.26.2.1.1 |
pvstpPortExternal port number.
This number corresponds to the ifTable ifIndex.ro PortNumber .switch-products.1.2.26.2.1.2 |
pvstpPortPriorityThe value of the priority field.rw INTEGER .switch-products.1.2.26.2.1.3 |
pvstpPortStateThe port state defined by the application of the
spanning tree protocol.ro Enumeration .switch-products.1.2.26.2.1.4 |
pvstpPortEnableThe enabled/disabled status of the port.rw Enumeration .switch-products.1.2.26.2.1.5 |
pvstpPortPathCostThe contribution of the port to the path cost.
Actual cost ranges from 1 to 65535. Zero is
a magic number which sets the cost
automatically.rw INTEGER .switch-products.1.2.26.2.1.6 |
pvstpPortDesignatedRootThe bridge identifier of the current root,
as transmitted by the current designated
bridge for the segment.ro BridgeId .switch-products.1.2.26.2.1.7 |
pvstpPortDesignatedCostPath cost for the designated port.ro INTEGER .switch-products.1.2.26.2.1.8 |
pvstpPortDesignatedBridgeBridge identifier of the bridge which this
port see as the designated bridge for the
segment.ro BridgeId .switch-products.1.2.26.2.1.9 |
pvstpPortDesignatedPortPort identifer of the port on the designated
bridge for the segment.ro OCTET STRING .switch-products.1.2.26.2.1.11 |
pvstpPortForwardTransitionsThe number of times the port has transitioned
from learning to forwarding state.ro Counter .switch-products.1.2.26.2.1.12 |
pvstpPortQuickWhen spanType is pvstp, turns
quick port reconfiguration ON/OFF for the port.rw Enumeration .switch-products.1.2.26.2.1.13 |
pvstpPortAutoPath cost is either Fixed or Auto. If
Auto, cost is calculated automatically,
and depends on media data rates and
link aggregation.ro Enumeration .switch-products.1.2.26.2.1.14 |
relayGroup OBJECT IDENTIFIER .switch-products.1.2.27 |
relayEnableEnabled-disabled status of BOOTP/DHCP relay agent.rw EnableStatus .switch-products.1.2.27.1 |
relayMaxHopsNumber of hops for the discard threshold for the
BOOTP/DHCP relay agent.rw INTEGER .switch-products.1.2.27.2 |
relayServerTableBOOTP/DHCP Relay Server Table. SEQUENCE OF RelayServerEntry .switch-products.1.2.27.3 |
relayServerEntryEach BOOTP/DHCP server entry consists of
a server index and an IP address. RelayServerEntry .switch-products.1.2.27.3.1 |
relayServerIndexIndex of a BOOTP/DHCP relay server IP address.ro INTEGER .switch-products.1.2.27.3.1.1 |
relayServerAddressIP address of a BOOTP/DHCP relay server.rw IpAddress .switch-products.1.2.27.3.1.2 |
portMirrorGroup OBJECT IDENTIFIER .switch-products.1.2.29 |
portMirrorTablePort Mirror Table Table. SEQUENCE OF PortMirrorEntry .switch-products.1.2.29.1 |
portMirrorEntryInformation which defines which ports are currently being mirrored. PortMirrorEntry .switch-products.1.2.29.1.1 |
portMirrorSourcePortPort number of port being mirrored.ro PortNumber .switch-products.1.2.29.1.1.1 |
portMirrorMonitorPortPort number of the monitor port.ro PortNumber .switch-products.1.2.29.1.1.2 |
portMirrorRowStatusUsed to control creation and deletion of rows.rw RowStatus (SNMPv2-TC) .switch-products.1.2.29.1.1.3 |
ipAccessCtlGroup OBJECT IDENTIFIER .switch-products.1.2.30 |
ipAccessCtlTableIP Access Control Table. SEQUENCE OF IpAccessCtlEntry .switch-products.1.2.30.1 |
ipAccessCtlEntryInformation which defines the rules for IP Access
Control. IpAccessCtlEntry .switch-products.1.2.30.1.1 |
ipAccessCtlRuleNumberRule number.ro INTEGER .switch-products.1.2.30.1.1.1 |
ipAccessCtlSourceAddressSource IP address of rule.rw IpAddress .switch-products.1.2.30.1.1.2 |
ipAccessCtlSourceMaskSource IP mask of rule.rw IpAddress .switch-products.1.2.30.1.1.3 |
ipAccessCtlDestinationAddressDestination IP address of rule.rw IpAddress .switch-products.1.2.30.1.1.4 |
ipAccessCtlDestinationMaskDestination IP mask of rule.rw IpAddress .switch-products.1.2.30.1.1.5 |
ipAccessCtlTypeType of rule.rw Enumeration .switch-products.1.2.30.1.1.6 |
ipAccessCtlRowStatusRule status.rw RowStatus (SNMPv2-TC) .switch-products.1.2.30.1.1.7 |
ipAccessCtlEnableEnabled-disabled status of IP Access Control.rw EnableStatus .switch-products.1.2.30.2 |
fdbGroup OBJECT IDENTIFIER .switch-products.1.2.31 |
fdbLearningModeFDB learning mode; either Independent VLAN
Learning(IVL), or Shared VLAN Learning(SVL).rw Enumeration .switch-products.1.2.31.1 |
fdbAgeTableForwarding database aging information. SEQUENCE OF FdbAgeEntry .switch-products.1.2.31.2 |
fdbAgeEntryFDB aging information. FdbAgeEntry .switch-products.1.2.31.2.1 |
fdbAgeIdFDB ID for this entry. In IVL mode, this object
is equivalent to the VLAN ID. In SVL mode, this
object is one for all entries.ro VlanId .switch-products.1.2.31.2.1.1 |
fdbAgeStatusEnable(1) or disable(2) aging. In SVL Mode, this object
controls aging for the entire FDB. In IVL Mode, this
object controls aging on a per-VLAN basis.rw EnableStatus .switch-products.1.2.31.2.1.2 |
fdbAgeTimeAging time for layer-2 entries. In SVL Mode, this object
controls aging for the entire FDB. In IVL Mode, this
object controls aging on a per-VLAN basis.rw INTEGER .switch-products.1.2.31.2.1.3 |