ISDN-OPT-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for ISDN-OPT-MIB.
99
Objects
Active
Status
2
Dependencies
Imported Objects
Objects
99 total| Object Name |
|---|
codex OBJECT IDENTIFIER .1.3.6.1.4.1.449 |
RFC1155-SMI Unknown .1.3.6.1.4.1.449 |
cdxProductSpecific OBJECT IDENTIFIER .1.3.6.1.4.1.449.2 |
cdx6500 OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1 |
cdx6500Configuration OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.2 |
cdx6500CfgGeneralGroup OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.2.2 |
isgIsdnCfgGroup OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.2.2.19 |
isgVGIsdnCfgChanTableThis table contains ISDN Channel Configuration parameters. SEQUENCE OF IsgVGIsdnCfgChanTableEntry .1.3.6.1.4.1.449.2.1.2.2.19.1 |
isgVGIsdnCfgChanTableEntryAn ISDN Channel Configuration Table Entry. SEQUENCE OF IsgVGIsdnCfgChanTableEntry .1.3.6.1.4.1.449.2.1.2.2.19.1.1 |
isgVGIsdnCfgEntryNumThis indicates the Channel Configuration Table Entry Number.ro INTEGER .1.3.6.1.4.1.449.2.1.2.2.19.1.1.1 |
isgVGIsdnCfgChanTypeISDN Channel Type.ro Enumeration .1.3.6.1.4.1.449.2.1.2.2.19.1.1.2 |
isgVGIsdnCfgDChanPortThe associated port for the ISDN D-channel.
dchanzero : Both B channels have access type Permanent.
No D Channel data.
dchanone : Packet Data on D-channel (Port 1 Type = X25) or
B-channel access type is Switched type.
dchanfour : Packet Data on D-Channel (Port 4 Type = X25).
nc : Skipped during configuration.rw Enumeration .1.3.6.1.4.1.449.2.1.2.2.19.1.1.3 |
isgVGIsdnCfgSwitchTypeSpecifies switch type for the central office.
bri1tr6Stype : German National ISDN.
bri5essStype : AT&T switch
briDms100Stype : DMS 100.
briKddStype : Japanese International Access ISDN.
briEtsiStype : Euro ISDB BRI (NET3).
briNi1Stype : National ISDN version 1.
briNttStype : Japanese National ISDN.
briTs013Stype : Australian National ISDN.
briVnStype : France National ISDN.rw Enumeration .1.3.6.1.4.1.449.2.1.2.2.19.1.1.4 |
isgVGIsdnCfgDChanTEIThe Terminal Endpoint Identifier value is provided by
the service provider. The range for TEI is 0..63, 127,
255. If the Switch Type is configured as DMS-1, the
possible range for TEI selection will be limited to
1..63. If TEI is configured to 255, the next valid TEI
will be used and if TEI is configured to 127, automatic
TEI negotiation will take place.rw INTEGER .1.3.6.1.4.1.449.2.1.2.2.19.1.1.5 |
isgVGIsdnCfgDPckTrafficenable : Signalling and X.25 data over the D Channel.
disable : Only signalling data over the D Channel.rw Enumeration .1.3.6.1.4.1.449.2.1.2.2.19.1.1.6 |
isgVGIsdnCfgDChanDNLocal Subscriber Directory Number (DN)
DN is provided by the ISDN service provider.rw DisplayString .1.3.6.1.4.1.449.2.1.2.2.19.1.1.7 |
isgVGIsdnCfgDSPIDThe Service Profile ID identifies the service profile
and is provided by the ISDN service provider.rw DisplayString .1.3.6.1.4.1.449.2.1.2.2.19.1.1.8 |
isgVGIsdnCfgFirstBChanPort0 : No call or TEI activity for the following objects
prefixed by `isgVGIsdnCfgFirst'
1-3 : The associated port whose traffic will be on the
ISDN B-channel which has the call and TEI objects
prefixed by `isgVGIsdnCfgFirst'.rw INTEGER .1.3.6.1.4.1.449.2.1.2.2.19.1.1.9 |
isgVGIsdnCfgFirstAccTypeperm : Dedicated (nailed-down) B-channel service.
cmd : Dialed B-channel service: Circuit Mode.
pmd : Dialed B-channel service: Packet Mode.
cvl : Dialed B-channel service: Circuit Mode
(Virtual Leased Line).
dov : dialed B-channel service: Circuit Mode
(Data over voice).rw Enumeration .1.3.6.1.4.1.449.2.1.2.2.19.1.1.10 |
isgVGIsdnCfgFirstCallDisablSTmThe Call Disable Start Time indicates whether ISDN
calls will/will-not be blocked. This field is
blank or displayed in the format `HHMM'.
blank : ISDN calls will not be blocked.
HHMM : ISDN calls will be blocked starting at
HH hour MM minutes.ro DisplayString .1.3.6.1.4.1.449.2.1.2.2.19.1.1.11 |
isgVGIsdnCfgFirstCallEnablSTmThe Call Enable Start Time indicates whether ISDN
calls will/will-not be blocked. This field is
blank or displayed in the format `HHMM'.
blank : ISDN calls will not be blocked.
HHMM : ISDN calls will be blocked starting at
HH hour MM minutes.ro DisplayString .1.3.6.1.4.1.449.2.1.2.2.19.1.1.12 |
isgVGIsdnCfgFirstSPBUThis port is configured to carry Same Port Backup
(SPBU) feature. This feature requires the corresponding
Port's Connection Type be SIMP.rw Enumeration .1.3.6.1.4.1.449.2.1.2.2.19.1.1.13 |
isgVGIsdnCfgFirstSPBUOptSame Port Backup (SPBU) feature options
This defines the switch back criteria for the backup
ISDN line.
NONE : No SPBU feature options.
TIMEOUT : Based on a pre-configured timeout period.
CALL : Based on the status of the Backup ISDN call.
Any combination of the above can be specified by
summing (e.g. TIMEOUT+CALL).rw DisplayString .1.3.6.1.4.1.449.2.1.2.2.19.1.1.14 |
isgVGIsdnCfgFirstSPBUTmOutSame Port Backup (SPBU) Timeout Counter.
This defines the ISDN call duration time before a return
to the leased line is attempted. This parameter is valid
when TIMEOUT option is selected. The timeout period is a
1 minute interval.rw INTEGER .1.3.6.1.4.1.449.2.1.2.2.19.1.1.15 |
isgVGIsdnCfgFirstRateThis parameter specifies the line speed for this channel.
rate64k : No Adaptation
rate128k : Bonded, no adaptation
rate56k : Rate Adapted to 64K
rate112k : Rate Adapted to 12D8K.rw Enumeration .1.3.6.1.4.1.449.2.1.2.2.19.1.1.16 |
isgVGIsdnCfgFirstTEIThe value for the TEI (Terminal Endpoint Identifier).
is provided by the service provider. The range is
0..63, 127, 255. Select 127 for automatic TEI
negotiation and 255 to use Packet D TEI.rw INTEGER .1.3.6.1.4.1.449.2.1.2.2.19.1.1.17 |
isgVGIsdnCfgFirstSPIDThe Service Profile ID identifies the service profile
and is provided by the ISDN service provider.rw DisplayString .1.3.6.1.4.1.449.2.1.2.2.19.1.1.18 |
isgVGIsdnCfgFirstDNLocal Subscriber Directory Number (DN)
DN is provided by the ISDN service provider.rw DisplayString .1.3.6.1.4.1.449.2.1.2.2.19.1.1.19 |
isgVGIsdnCfgFirstSubAddrOutgoing call : This subaddress will be sent in the call
setup message.
Incoming call : This subaddress will be used for call
verification if provided.rw DisplayString .1.3.6.1.4.1.449.2.1.2.2.19.1.1.20 |
isgVGIsdnCfgFirstOutDialNum1The phone number to dial when establishing an ISDN
outbound call.rw DisplayString .1.3.6.1.4.1.449.2.1.2.2.19.1.1.21 |
isgVGIsdnCfgFirstOutDialNum2The phone number to dial if B1 Outbound Dial Number #1
is not available. Alternate attempts will be made between
Number#1 and Number#2.rw DisplayString .1.3.6.1.4.1.449.2.1.2.2.19.1.1.22 |
isgVGIsdnCfgFirstDialRetryIntrvlThe Dial Retry Timer defines the time (1 second
interval) between ISDN dial attempts. The range
is 0, 15-3600. The timer will be disabled by a
configuration of 0.rw INTEGER .1.3.6.1.4.1.449.2.1.2.2.19.1.1.23 |
isgVGIsdnCfgFirstNumCallRetriesThe Dial Retry Counter specifies the number of times
the ISDN will attempt calling at the Call Retry Interval.
The value of 0 will allow unlimited number of attempts.rw INTEGER .1.3.6.1.4.1.449.2.1.2.2.19.1.1.24 |
isgVGIsdnCfgSecondChanPort0 : No call or TEI activity for the following objects
prefixed by `isgVGIsdnCfgSecond'
1-3 : The associated port whose traffic will be on the
ISDN B-channel which has the call and TEI objects
prefixed by `isgVGIsdnCfgSecond'.rw INTEGER .1.3.6.1.4.1.449.2.1.2.2.19.1.1.25 |
isgVGIsdnCfgSecondAccTypeperm : Dedicated (nailed-down) B-channel service.
cmd : Dialed B-channel service: Circuit Mode.
pmd : Dialed B-channel service: Packet Mode.
cvl : Dialed B-channel service: Circuit Mode
(Virtual Leased Line).
dov : dialed B-channel service: Circuit Mode
(Data over voice).rw Enumeration .1.3.6.1.4.1.449.2.1.2.2.19.1.1.26 |
isgVGIsdnCfgSecondCallDisablSTmThe Call Disable Start Time indicates whether ISDN
calls will/will-not be blocked. This field is blank
or displayed in the format `HHMM'.
blank : ISDN calls will not be blocked.
HHMM : ISDN calls will be blocked starting at
HH hour MM minutes.ro DisplayString .1.3.6.1.4.1.449.2.1.2.2.19.1.1.27 |
isgVGIsdnCfgSecondCallEnablSTmThe Call Enable Start Time indicates whether ISDN
calls will/will-not be blocked. This field is blank
or displayed in the format `HHMM'.
blank : ISDN calls will not be blocked.
HHMM : ISDN calls will be blocked starting at
HH hour MM minutes.ro DisplayString .1.3.6.1.4.1.449.2.1.2.2.19.1.1.28 |
isgVGIsdnCfgSecondSPBUThis port is configured to carry Same Port Backup
(SPBU) feature. This feature requires the corresponding
Port's Connection Type be SIMP.rw Enumeration .1.3.6.1.4.1.449.2.1.2.2.19.1.1.29 |
isgVGIsdnCfgSecondSPBUOptSame Port Backup (SPBU) feature options
This defines the switch back criteria for the backup
ISDN line.
NONE : No SPBU feature options.
TIMEOUT : Based on a pre-configured timeout period.
CALL : Based on the status of the Backup ISDN call.
Any combination of the above can be specified by
summing (e.g. TIMEOUT+CALL).rw DisplayString .1.3.6.1.4.1.449.2.1.2.2.19.1.1.30 |
isgVGIsdnCfgSecondSPBUTmOutSame Port Backup (SPBU) Timeout Counter.
This defines the ISDN call duration time before a return
to the leased line is attempted. This parameter is valid
when TIMEOUT option is selected.The timeout period is a 1
minute interval.rw INTEGER .1.3.6.1.4.1.449.2.1.2.2.19.1.1.31 |
isgVGIsdnCfgSecondRateThis parameter specifies the line speed for this channel.
rate64k : No Adaptation
rate56k : Rate Adapted to 64K.rw Enumeration .1.3.6.1.4.1.449.2.1.2.2.19.1.1.32 |
isgVGIsdnCfgSecondTEIThe value for the TEI (Terminal Endpoint Identifier).
is provided by the service provider. The range is
0..63, 127, 255. Select 127 for automatic TEI
negotiation and 255 to use TEI selected for B1.rw INTEGER .1.3.6.1.4.1.449.2.1.2.2.19.1.1.33 |
isgVGIsdnCfgSecondSPIDThe Service Profile ID identifies the service profile
and is provided by the ISDN service provider.rw DisplayString .1.3.6.1.4.1.449.2.1.2.2.19.1.1.34 |
isgVGIsdnCfgSecondDNLocal Subscriber Directory Number (DN)
DN is provided by the ISDN service provider.rw DisplayString .1.3.6.1.4.1.449.2.1.2.2.19.1.1.35 |
isgVGIsdnCfgSecondSubAddrOutgoing call : This subaddress will be sent in the call
setup message.
Incoming call : This subaddress will be used for call
verification if provided.rw DisplayString .1.3.6.1.4.1.449.2.1.2.2.19.1.1.36 |
isgVGIsdnCfgSecondOutDialNum1The phone number to dial when establishing an
ISDN outbound call.rw DisplayString .1.3.6.1.4.1.449.2.1.2.2.19.1.1.37 |
isgVGIsdnCfgSecondOutDialNum2The phone number to dial if B1 Outbound Dial Number #1
is not available. Alternate attempts will be made between
Number#1 and Number#2.rw DisplayString .1.3.6.1.4.1.449.2.1.2.2.19.1.1.38 |
isgVGIsdnCfgSecondDialRetryIntrvlThe Dial Retry Timer defines the time (1 second interval)
between ISDN dial attempts. The range is 0, 15-3600. The
timer will be disabled by a configuration of 0.rw INTEGER .1.3.6.1.4.1.449.2.1.2.2.19.1.1.39 |
isgVGIsdnCfgSecondNumCallRetriesThe Dial Retry Counter specifies the number of times
the ISDN will attempt calling at the Call Retry Interval.
The value of 0 will allow unlimited number of attempts.rw INTEGER .1.3.6.1.4.1.449.2.1.2.2.19.1.1.40 |
isgVGIsdnCfgFirstPlainOldTelSetnone: No Telephone support required
pots1: Plain Old Telephone Set 1 connectedrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.2.2.19.1.1.41 |
isgVGIsdnCfgFirstCallPermout - Initiates Call only, does not accept call
inc - Accepts Call only, does not send call to networkrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.2.2.19.1.1.42 |
isgVGIsdnCfgFirstChSelectexclusive - implies channel requested will be fixed with
the configured selection
preferred - it will be up to the network to grant a channel
for connectionrw Enumeration .1.3.6.1.4.1.449.2.1.2.2.19.1.1.43 |
isgVGIsdnCfgSecondPlainOldTelSetnone: No Telephone support required
pots1: Plain Old Telephone Set 1 connected
pots2: Plain Old Telephone Set 2 connectedrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.2.2.19.1.1.44 |
isgVGIsdnCfgSecondCallPermout - Initiates Call only, does not accept call
inc - Accepts Call only, does not send call to networkrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.2.2.19.1.1.45 |
isgVGIsdnCfgSecondChSelectexclusive - implies channel requested will be fixed with
the configured selection
preferred - it will be up to the network to grant a channel
for connectionrw Enumeration .1.3.6.1.4.1.449.2.1.2.2.19.1.1.46 |
cdx6500Statistics OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.3 |
cdx6500StatOtherStatsGroup OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.3.2 |
isgIsdnStatsGroup OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.3.2.9 |
isgVGIsdnStats OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.3.2.9.1 |
isgVGIsdnCCStatsTblISDN DSL Current Call Statistics Table. SEQUENCE OF IsgVGIsdnCCStatsTblEntry .1.3.6.1.4.1.449.2.1.3.2.9.1.1 |
isgVGIsdnCCStatsTblEntryCurrent Call Statistics Table Entries. IsgVGIsdnCCStatsTblEntry .1.3.6.1.4.1.449.2.1.3.2.9.1.1.1 |
isgVGIsdnCCStatsDSLNumDigital Service Loop Number.ro INTEGER .1.3.6.1.4.1.449.2.1.3.2.9.1.1.1.1 |
isgVGIsdnCCStatsChTypeISDN Channel Type.ro Enumeration .1.3.6.1.4.1.449.2.1.3.2.9.1.1.1.2 |
isgVGIsdnCCStatsSwtchTypeSwitch Type.
bri1tr6Stype : German National ISDN.
bri5essStype : AT&T switch
briDms100Stype : DMS 100.
briKddStype : Japanese International Access ISDN.
briEtsiStype : Euro ISDB BRI (NET3).
briNi1Stype : National ISDN version 1.
briNttStype : Japanese National ISDN.
briTs013Stype : Australian National ISDN.
briVnStype : France National ISDN.
unsupported : Unsupported Switch Type.ro Enumeration .1.3.6.1.4.1.449.2.1.3.2.9.1.1.1.3 |
isgVGIsdnCCStatsL1StateLevel1 State.
l1Setup : Setup State.
l1Active : Active State.
l1Deactive : Inactive State.
l1B1Loop : Loop Test State.
l1B2Loop : Loop Test State.
l1B1B2Loop : Loop Test State.
l12BDLoop : Loop Test State.
unknown : Loop Test State.ro Enumeration .1.3.6.1.4.1.449.2.1.3.2.9.1.1.1.4 |
isgVGIsdnCCStatsTEITerminal Endpoint Identifier.ro INTEGER .1.3.6.1.4.1.449.2.1.3.2.9.1.1.1.5 |
isgVGIsdnCCStatsCallgAddrCurrent Call Statistics : Calling Address.ro DisplayString .1.3.6.1.4.1.449.2.1.3.2.9.1.1.1.6 |
isgVGIsdnCCStatsCalldAddrCurrent Call Statistics : Called Address.ro DisplayString .1.3.6.1.4.1.449.2.1.3.2.9.1.1.1.7 |
isgVGIsdnCCStatsSubaddrCurrent Call Statistics : Call Subaddress.ro DisplayString .1.3.6.1.4.1.449.2.1.3.2.9.1.1.1.8 |
isgVGIsdnCCStatsDirectionCurrent Call Statistics : Call Direction.
noCall : Channel is idle.
outgoing : Call is coming from Vanguard
into the ISDN network.
incoming : Call is coming into Vanguard
from the ISDN Network.
collision : A Call collision is detected.ro Enumeration .1.3.6.1.4.1.449.2.1.3.2.9.1.1.1.9 |
isgVGIsdnCCStatsAccTypeCurrent Call Statistics : Channel Access Type.
permanent : Permanent B is selected.
cktMode : Dialed B-channel service: Circuit Mode.
pktMode : Dialed B-channel service: Packet Mode.
cvl : Dialed B-channel service: Circuit Mode
(Virtual Leased Line).ro Enumeration .1.3.6.1.4.1.449.2.1.3.2.9.1.1.1.10 |
isgVGIsdnCCStatsCallStatusCurrent Call Statistics : Call Status.
waitInit : FIT waiting for SPID registration.
initFail : FIT's SPID registration has failed.
termIdle : Terminal is currently idle
(ready for calls).
callInit : An outbound call setup is sent.
discSent : A disconnect request is sent.
hostProc : In Call Proc./Alert State.
callConn : An outbound/inbound call is connected.
notApplicable : Not applicable to this channel.
This object is only applicable to B1/B2 Channels.ro Enumeration .1.3.6.1.4.1.449.2.1.3.2.9.1.1.1.11 |
isgVGIsdnCCStatsLineSpeedCurrent Call Statistics : Line Speed.
rate64k : No Adaptation
rate128k : Bonded, no adaptation
rate56k : Rate Adapted to 64K
rate112k : Rate Adapted to 12D8K.ro Enumeration .1.3.6.1.4.1.449.2.1.3.2.9.1.1.1.12 |
isgVGIsdnCCStatsPortConnCurrent Call Statistics : Port number to carry this call.ro INTEGER .1.3.6.1.4.1.449.2.1.3.2.9.1.1.1.13 |
isgVGIsdnCCStatsCauseCodeCurrent Call Statistics : Cause Code sent/received in the
Q.931 message.ro INTEGER .1.3.6.1.4.1.449.2.1.3.2.9.1.1.1.14 |
isgVGIsdnCCStatsCallStartedCurrent Call Statistics : Call Start Time.ro DisplayString .1.3.6.1.4.1.449.2.1.3.2.9.1.1.1.15 |
isgVGIsdnCCStatsDChanStatusenabled : D channel is enabled.
disabled : D channel is disabled.ro Enumeration .1.3.6.1.4.1.449.2.1.3.2.9.1.1.1.16 |
isgVGIsdnCCStatsTrmStatusfitWaitInit : Fully Initializing Terminal (FIT)
is waiting for SPID registration.
fitFailed : FIT registration failed, check alarm
for cause.
fitTimeout : SPID registration has timed out,
waiting for retry.
networkTimeout : Network is not responding to SPID
registration sent.
spidError : Network rejected SPID registration
due to error in the ID.
online : Terminal is ready for ISDN
communication.ro Enumeration .1.3.6.1.4.1.449.2.1.3.2.9.1.1.1.17 |
isgVGIsdnCCStatsTrmTeiTerminal (B1/B2) TEI.ro INTEGER .1.3.6.1.4.1.449.2.1.3.2.9.1.1.1.18 |
isgVGIsdnCHStatsTblISDN DSL Call History Table. SEQUENCE OF IsgVGIsdnCHStatsTblEntry .1.3.6.1.4.1.449.2.1.3.2.9.1.2 |
isgVGIsdnCHStatsTblEntryISDN DSL Call History Table Entries. IsgVGIsdnCHStatsTblEntry .1.3.6.1.4.1.449.2.1.3.2.9.1.2.1 |
isgVGIsdnCHStatsDSLNumDigital Service Loop Number.ro INTEGER .1.3.6.1.4.1.449.2.1.3.2.9.1.2.1.1 |
isgVGIsdnCHStatsChTypeISDN Channel Type.ro Enumeration .1.3.6.1.4.1.449.2.1.3.2.9.1.2.1.2 |
isgVGIsdnCHStatsSessionCall Session Number tracked.
0 : Most Recent call.
1 : Previous call.
2 : Oldest call.ro INTEGER .1.3.6.1.4.1.449.2.1.3.2.9.1.2.1.3 |
isgVGIsdnCHStatsNumCalldIf the call is outgoing, this is the phone number that
has been called.
If the call is incoming, this is the number that is calling
(provided the line has subscribed to Caller ID Display.ro DisplayString .1.3.6.1.4.1.449.2.1.3.2.9.1.2.1.4 |
isgVGIsdnCHStatsDirectionDirection of the call.
noCall : Channel is idle.
outgoing : Call is coming from Vanguard
into the ISDN network.
incoming : Call is coming into Vanguard
from the ISDN Network.
collision : A Call collision is detected.ro Enumeration .1.3.6.1.4.1.449.2.1.3.2.9.1.2.1.5 |
isgVGIsdnCHStatsCauseCodeCause Code sent/received in the Q.931 message.ro INTEGER .1.3.6.1.4.1.449.2.1.3.2.9.1.2.1.6 |
isgVGIsdnCHStatsLineSpeedLine Speed for the call.
rate64k : No Adaptation
rate56k : Rate Adapted to 64K
rate0k : Rate Adapted to 0K.ro Enumeration .1.3.6.1.4.1.449.2.1.3.2.9.1.2.1.7 |
isgVGIsdnCHStatsAsscPortAssociated Port number to carry this call.ro INTEGER .1.3.6.1.4.1.449.2.1.3.2.9.1.2.1.8 |
isgVGIsdnCHStatsStrtTmCall Start Time.ro DisplayString .1.3.6.1.4.1.449.2.1.3.2.9.1.2.1.9 |
isgVGIsdnCHStatsEndTmCall End Time.ro DisplayString .1.3.6.1.4.1.449.2.1.3.2.9.1.2.1.10 |
isgVGIsdnPRICCStatsTblISDN PRI DSL Current Call Statistics Table. SEQUENCE OF IsgVGIsdnPRICCStatsTblEntry .1.3.6.1.4.1.449.2.1.3.2.9.1.3 |
isgVGIsdnPRICCStatsTblEntryPRI Current Call Statistics Table Entries. IsgVGIsdnPRICCStatsTblEntry .1.3.6.1.4.1.449.2.1.3.2.9.1.3.1 |
isgVGIsdnPRICCStatsDSLNumDigital Service Loop Number.ro INTEGER .1.3.6.1.4.1.449.2.1.3.2.9.1.3.1.1 |
isgVGIsdnPRICCStatsSwtchTypeSwitch Type.
bri1tr6Stype : German National ISDN.
priNi2Stype : National ISDN version 2.
pri5essStype : AT&T switch
priDms100Stype : DMS 100.
priNttStype : Japanese National ISDN.
priTs014Stype : Australian National ISDN.
priEtsiStype : Euro ISDB BRI (NET3).
priQsigMStype : Master Side QSIG PBX.
priQsigSStype : Slave Side QSIG PBX.
priT1QsigMStype : T1 Master Side QSIG PBX.
priT1QsigSStype : T1 Slave Side QSIG PBX.
unsupported : Unsupported Switch Type.ro Enumeration .1.3.6.1.4.1.449.2.1.3.2.9.1.3.1.2 |
isgVGIsdnPRICCStatsDChannelStateD Channel Status.
dChannelUp : D Channel Up.
dChannelDown : D Channel Down.
unknown : Loop Test State.ro Enumeration .1.3.6.1.4.1.449.2.1.3.2.9.1.3.1.3 |
cdx6500Controls OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.4 |
isgIsdnCtrlGroup OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.4.8 |
isgVGIsdnBootChannelBoot the ISDN channels.rw Enumeration .1.3.6.1.4.1.449.2.1.4.8.1 |