INTEL-MPLINK-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
111
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
111 total| Object Name |
|---|
mpl OBJECT IDENTIFIER .1.3.6.1.4.1.208.2.20 |
INTEL-GEN-MIB Unknown .1.3.6.1.4.1.208.2.20 |
mplLockEventLock state changed to <mplServiceLock> for link <mplServiceNumber>.
This trap is sent when an MP Link is locked or
unlocked from local management or via SNMP. TRAP-TYPE .1.3.6.1.4.1.208.2.20.0.1 |
mplWanRetriesEventMax. retries exceeded (<mplWanRetries>) for link <mplWanNumber>.
This trap is sent when an MP Link has had more
failed connect-attempts than allowed in the
configuration. TRAP-TYPE .1.3.6.1.4.1.208.2.20.0.2 |
mplWanActivityEventDaily Activity Limit has been reached. Link <mplWanNumber> locked.
This trap is sent when the Daily Activity
Limit has been reached and locked the link. TRAP-TYPE .1.3.6.1.4.1.208.2.20.0.3 |
mplWanTimerEventLink timer has changed lock state to <WanTimer> for link <WanNumber>.
This trap is sent when an MP Link timer has
locked or unlocked the link. TRAP-TYPE .1.3.6.1.4.1.208.2.20.0.4 |
mplService OBJECT IDENTIFIER .1.3.6.1.4.1.208.2.20.1 |
mplServiceTableThis table contains information on MP Links.
These entries applies to LAN entries as well as
WAN entries. SEQUENCE OF MplServiceEntry .1.3.6.1.4.1.208.2.20.1.1 |
mplServiceEntryInformation on a particular MP Link. MplServiceEntry .1.3.6.1.4.1.208.2.20.1.1.1 |
mplServiceNumberThe MP Link number. The MP Link number is the
same as the ifIndex for the corresponding
upper group in the MIB-2 ifGroup.ro INTEGER .1.3.6.1.4.1.208.2.20.1.1.1.1 |
mplServiceSlotNumberThe Slot position of the card. Set to 0 for
stand-alone products.ro INTEGER .1.3.6.1.4.1.208.2.20.1.1.1.2 |
mplServicePlugNumberThe plug number of the physical interface to
which the MP Link is associated.ro INTEGER .1.3.6.1.4.1.208.2.20.1.1.1.3 |
mplServicePlugNameThe name of the physical interface to which
the MP Link is associated.ro DisplayString .1.3.6.1.4.1.208.2.20.1.1.1.4 |
mplServiceAttachmentThe connector type used to connect the router
to the LAN or WAN.ro Attachment .1.3.6.1.4.1.208.2.20.1.1.1.5 |
mplServiceProviderThe type of provider for this MP Link. For WAN
links this specifies the actual protocol
stack.ro Enumeration .1.3.6.1.4.1.208.2.20.1.1.1.6 |
mplServiceBytesSentUpperThe upper 32 bits of the 64 bits counter which
is the number of octets (bytes) sent via the MP
Link.ro Counter .1.3.6.1.4.1.208.2.20.1.1.1.7 |
mplServiceBytesSentLowerThe lower 32 bits of the 64 bits counter which
is the number of octets (bytes) sent via the MP
Link.ro Counter .1.3.6.1.4.1.208.2.20.1.1.1.8 |
mplServiceBytesReceivedUpperThe lower 32 bits of the 64 bits counter which
is the number of octets (bytes) sent via the MP
Link.ro Counter .1.3.6.1.4.1.208.2.20.1.1.1.9 |
mplServiceBytesReceivedLowerThe lower 32 bits of the 64 bits counter which
is the number of octets (bytes) received via
the MP Link.ro Counter .1.3.6.1.4.1.208.2.20.1.1.1.10 |
mplServiceLockIndicates whether an MP Link has been locked
from local management. The link may be unlocked
by setting the value to 'off' and locked by
setting the value to 'on'.rw OnOff .1.3.6.1.4.1.208.2.20.1.1.1.11 |
mplLanSpecific OBJECT IDENTIFIER .1.3.6.1.4.1.208.2.20.2 |
mplLanTableThis table contains information on LAN MP
Links. SEQUENCE OF MplLanEntry .1.3.6.1.4.1.208.2.20.2.1 |
mplLanEntryInformation on a particular LAN MP Link. MplLanEntry .1.3.6.1.4.1.208.2.20.2.1.1 |
mplLanNumberThe LAN MP Link number. The MP Link number is
the same as the ifIndex for the corresponding
upper group in the MIB-2 ifGroup.ro INTEGER .1.3.6.1.4.1.208.2.20.2.1.1.1 |
mplLanRxCRCErrorsThe number of frames received which were
discarded due to Cyclic Redundancy Check (CRC)
errors.ro Counter .1.3.6.1.4.1.208.2.20.2.1.1.2 |
mplLanRxOverrunThe number of frames received which were lost
due to RAM overloads within the router. This
should not occur.ro Counter .1.3.6.1.4.1.208.2.20.2.1.1.3 |
mplLanRxLongThe number of frames received which were
discarded due to being larger than the maximum
allowable length on the LAN.ro Counter .1.3.6.1.4.1.208.2.20.2.1.1.4 |
mplLanRxOverflowThe number of frames received which were
discarded due to lack of buffer capacity.ro Counter .1.3.6.1.4.1.208.2.20.2.1.1.5 |
mplLanRxAlnErrorsThe number of frames received which were
discarded due to having the wrong frame
length.ro Counter .1.3.6.1.4.1.208.2.20.2.1.1.6 |
mplLanRxOutsThe number of frames received which were
processed by higher layer protocols.ro Counter .1.3.6.1.4.1.208.2.20.2.1.1.7 |
mplLanRxShortThe number of frames received which were
discarded due to being shorter than the smallest
allowable length on the LAN.ro Counter .1.3.6.1.4.1.208.2.20.2.1.1.8 |
mplLanTxDeferredThe number of outgoing frames which were
discarded due to a busy link.ro Counter .1.3.6.1.4.1.208.2.20.2.1.1.9 |
mplLanTxUnderrunThe number of outgoing frames which were
discarded due to overload.ro Counter .1.3.6.1.4.1.208.2.20.2.1.1.10 |
mplLanTxSQEFailureThe number of outbound frames which had
Signal Quality Errors (SQE).ro Counter .1.3.6.1.4.1.208.2.20.2.1.1.11 |
mplLanTxExcDeferralThe number of transmission attempts which were delayed
for more than 3.2 ms.ro Counter .1.3.6.1.4.1.208.2.20.2.1.1.12 |
mplLanTxCollExceedThe number of outbound frames which were
discarded due to exceeding 16 collisions on the
Ethernet.ro Counter .1.3.6.1.4.1.208.2.20.2.1.1.13 |
mplLanTxLateCollThe number of collisions occurring after the
first 512 bytes of a frame had been
transmitted.ro Counter .1.3.6.1.4.1.208.2.20.2.1.1.14 |
mplLanTxCollisionsThe number of outgoing frames which were
discarded due to collisions that occurred
during transmissions.ro Counter .1.3.6.1.4.1.208.2.20.2.1.1.15 |
mplLanTxNoCarrierThe number of No Carrier detections during
transmissions.ro Counter .1.3.6.1.4.1.208.2.20.2.1.1.16 |
mplWanSpecific OBJECT IDENTIFIER .1.3.6.1.4.1.208.2.20.3 |
mplWanTableThis table contains information on WAN MP
Links. SEQUENCE OF MplWanEntry .1.3.6.1.4.1.208.2.20.3.1 |
mplWanEntryInformation on a particular WAN MP Link. MplWanEntry .1.3.6.1.4.1.208.2.20.3.1.1 |
mplWanNumberThe WAN MP Link number. The MP Link number is
the same as the ifIndex for the corresponding
upper group in the MIB-2 ifGroup.ro INTEGER .1.3.6.1.4.1.208.2.20.3.1.1.1 |
mplWanDataStateThe state of the MP Link seen from the higher
layer protocol.ro DataState .1.3.6.1.4.1.208.2.20.3.1.1.2 |
mplWanDataStateTimerThe time in seconds since the MP Link entered
the Data State.ro INTEGER .1.3.6.1.4.1.208.2.20.3.1.1.3 |
mplWanConnectStateIndicates the connection state of the WAN MP
Link.ro ConnectState .1.3.6.1.4.1.208.2.20.3.1.1.4 |
mplWanConnectStateTimerThe time in seconds since the MP Link entered
the Connect State.ro INTEGER .1.3.6.1.4.1.208.2.20.3.1.1.5 |
mplWanCompressionIndicates if data compression is used over the
WAN MP Link. For frame relay links compression
is not negotiated. For all other WAN protocols
the compression will remain 'off' if not
configured in both routers over the link.ro OnOff .1.3.6.1.4.1.208.2.20.3.1.1.6 |
mplWanCompressionTypeProprietary compression is used for LAPB and
X.25 MP Links. For all other WAN protocols the
Stac compression algorithm is used.ro CompType .1.3.6.1.4.1.208.2.20.3.1.1.7 |
mplWanCallsSucceededThe number of outgoing call which succeeded in
making the connection.ro Counter .1.3.6.1.4.1.208.2.20.3.1.1.8 |
mplWanCallsFailedThe number of outgoing call which failed to
make the connection.ro Counter .1.3.6.1.4.1.208.2.20.3.1.1.9 |
mplWanCallsAcceptedThe number of incoming calls which were
accepted on this link.ro Counter .1.3.6.1.4.1.208.2.20.3.1.1.10 |
mplWanCallsRejectedThe number of incoming calls which were
rejected on this link.ro Counter .1.3.6.1.4.1.208.2.20.3.1.1.11 |
mplWanRetriesThe number of retries made for outgoing
calls. May be set to zero which causes the
call sequence to restarted.rw INTEGER .1.3.6.1.4.1.208.2.20.3.1.1.12 |
mplWanDirectionShows who initiated the call. 'incoming' if the
call was initiated by the remote router and
'outgoing' if the call was inititated by this
router. For PPP Multi Links the direction
refers the the direction of the first slave
link.ro Direction .1.3.6.1.4.1.208.2.20.3.1.1.13 |
mplWanHasBackupIndicates whether this link has a backup link
configured for it.ro OnOff .1.3.6.1.4.1.208.2.20.3.1.1.14 |
mplWanBackupForShows the primary link for which this link is
the backup. The value 0 indicates that this is
not a backup link.ro INTEGER .1.3.6.1.4.1.208.2.20.3.1.1.15 |
mplWanBackupForAttachmentIndicates whether this link is a backup for an
attachment.ro OnOff .1.3.6.1.4.1.208.2.20.3.1.1.16 |
mplWanFlagsWAN Flags
dataCompressionMask 0x0001
acceptIncomingMask 0x0002
permitOutgoingMask 0x0004
permitTimeCutMask 0x0008
chapMask 0x0010 - CHAP, PPP only
papMask 0x0020 - PAP, PPP only
onlyReplyChapMask 0x0040
slaveLink 0x0080
blockOutgoing 0x0100
blockIncoming 0x0200
isLeased 0x0400
dataCompressionMode 0x0800 - PPP new-stac compression flag
activitySoft 0x1000 - Activity timer only sends trapro INTEGER .1.3.6.1.4.1.208.2.20.3.1.1.17 |
mplWanPppMasterIndicates the master link for a slave link.
For master links and links not associated with
a PPP Multi Link the value is 0.ro INTEGER .1.3.6.1.4.1.208.2.20.3.1.1.18 |
mplWanPppSlaveUpCountThe number of slave links in Connect State
'up'. For slave links and links not associated
with a PPP Multi Link the value is 1.ro INTEGER .1.3.6.1.4.1.208.2.20.3.1.1.19 |
mplWanActivityTimeLeftThe time remaining in seconds until the Daily
Activity Limit will close and lock the link.
When the Daily Activity Limit has been reached,
the link can be activated by setting
mplWanActivity to 'on'.ro INTEGER .1.3.6.1.4.1.208.2.20.3.1.1.20 |
mplWanActivityIndicates whether the Daily Activity Limit has
been reached and locked the link. To unlock the
link set the value to 'off'. It is not possible
to set to the value to 'on'.rw OnOff .1.3.6.1.4.1.208.2.20.3.1.1.21 |
mplWanTimerIndicates whether an MP Link timer has locked
the link. 'on' means the link is locked.ro OnOff .1.3.6.1.4.1.208.2.20.3.1.1.22 |
mplWanTimeTillTimecutTime left in seconds until time cutro INTEGER .1.3.6.1.4.1.208.2.20.3.1.1.23 |
mplWanLastPacketThe first byte in this string identifies the type of packet that
opened the link the last time.
IP 1 Internet Protocols 0xcc
IPX 2 Novell IPX 0x800000008137
STA_ETH 3 Bridge-Ether 0x800080c20007
STA_FRAG 4 Bridge-Frag 0x800080c2000d
STA_BPDU 5 Bridge-BPDU 0x800080c2000e
STA_CRAY 6 Bridge-Cray 0x800000800500
STA_ETH_FCS 15 Bridge-FCS
After this byte follows a part of the packet header.ro OCTET STRING .1.3.6.1.4.1.208.2.20.3.1.1.24 |
mplWanInCallsPlaced??? Number of calls placed.ro Counter .1.3.6.1.4.1.208.2.20.3.1.1.25 |
mplWanOutCallsPlaced??? Number of calls placed.ro Counter .1.3.6.1.4.1.208.2.20.3.1.1.26 |
mplWanInTimeActiveThe time in seconds that the link was in the Up state for
incoming calls.ro INTEGER .1.3.6.1.4.1.208.2.20.3.1.1.27 |
mplWanOutTimeActiveThe time in seconds that the link was in the Up state for
outcoming calls.ro INTEGER .1.3.6.1.4.1.208.2.20.3.1.1.28 |
mplWanTotalTime???ro INTEGER .1.3.6.1.4.1.208.2.20.3.1.1.29 |
mplCompTableCompression table with counters and other information
regarding the Transmit and Receive Decoder. SEQUENCE OF MplCompEntry .1.3.6.1.4.1.208.2.20.3.2 |
mplCompEntry MplCompEntry .1.3.6.1.4.1.208.2.20.3.2.1 |
mplCompNumberThe WAN MP Link number. The MP Link number is
the same as the ifIndex for the corresponding
upper group in the MIB-2 ifGroup.ro INTEGER .1.3.6.1.4.1.208.2.20.3.2.1.1 |
mplCompRxDecRxBytesTotalUpperThe upper 32 bits of the 64 bits counter which is the number of
bytes received by the Receive Decoder.ro Counter .1.3.6.1.4.1.208.2.20.3.2.1.2 |
mplCompRxDecRxBytesTotalLowerThe lower 32 bits of the 64 bits counter which is the number of
bytes received by the Receive Decoder.ro Counter .1.3.6.1.4.1.208.2.20.3.2.1.3 |
mplCompRxDecRxBytesDecompUpperThe upper 32 bits of the 64 bits counter which is the number of
bytes sent by the Receive Decoder.ro Counter .1.3.6.1.4.1.208.2.20.3.2.1.4 |
mplCompRxDecRxBytesDecompLowerThe lower 32 bits of the 64 bits counter which is the number of
bytes sent by the Receive Decoder.ro Counter .1.3.6.1.4.1.208.2.20.3.2.1.5 |
mplCompRxDecDecompressedUpperThe upper 32 bits of the 64 bits counter which is the number of
packets decompressed by the Receive Decoder.ro Counter .1.3.6.1.4.1.208.2.20.3.2.1.6 |
mplCompRxDecDecompressedLowerThe lower 32 bits of the 64 bits counter which is the number of
packets decompressed by the Receive Decoder.ro Counter .1.3.6.1.4.1.208.2.20.3.2.1.7 |
mplCompRxDecAllocErrorsUpperThe upper 32 bits of the 64 bits counter which is the number of
allocation errors in the Receive Decoder.ro Counter .1.3.6.1.4.1.208.2.20.3.2.1.8 |
mplCompRxDecAllocErrorsLowerThe lower 32 bits of the 64 bits counter which is the number of
allocation errors in the Receive Decoder.ro Counter .1.3.6.1.4.1.208.2.20.3.2.1.9 |
mplCompRxDecRemoteInitsNumber of remote initializations by the Receive Decoder.ro Counter .1.3.6.1.4.1.208.2.20.3.2.1.10 |
mplCompTxEncInBytesTotalUpperThe upper 32 bits of the 64 bits counter which is the number of
bytes received by the Transmit Decoder.ro Counter .1.3.6.1.4.1.208.2.20.3.2.1.11 |
mplCompTxEncInBytesTotalLowerThe lower 32 bits of the 64 bits counter which is the number of
bytes received by the Transmit Decoder.ro Counter .1.3.6.1.4.1.208.2.20.3.2.1.12 |
mplCompTxEncTxBytesCompUpperThe upper 32 bits of the 64 bits counter which is the number of
bytes sent by the Transmit Decoder.ro Counter .1.3.6.1.4.1.208.2.20.3.2.1.13 |
mplCompTxEncTxBytesCompLowerThe lower 32 bits of the 64 bits counter which is the number of
bytes sent by the Transmit Decoder.ro Counter .1.3.6.1.4.1.208.2.20.3.2.1.14 |
mplCompTxEncCompressedUpperThe upper 32 bits of the 64 bits counter which is the number of
packets compressed by the Transmit Decoder.ro Counter .1.3.6.1.4.1.208.2.20.3.2.1.15 |
mplCompTxEncCompressedLowerThe lower 32 bits of the 64 bits counter which is the number of
packets compressed by the Transmit Decoder.ro Counter .1.3.6.1.4.1.208.2.20.3.2.1.16 |
mplCompTxEncAllocErrorsUpperThe upper 32 bits of the 64 bits counter which is the number of
allocation errors in the Transmit Decoder.ro Counter .1.3.6.1.4.1.208.2.20.3.2.1.17 |
mplCompTxEncAllocErrorsLowerThe lower 32 bits of the 64 bits counter which is the number of
allocation errors in the Transmit Decoder.ro Counter .1.3.6.1.4.1.208.2.20.3.2.1.18 |
mplCompTxEncLocalInitsNumber of local initializations by the Receive Decoder.ro Counter .1.3.6.1.4.1.208.2.20.3.2.1.19 |
mplCompTxEncTransmitErrorsNumber of transmit errorsro INTEGER .1.3.6.1.4.1.208.2.20.3.2.1.20 |
mplCompTxEncQueueLengthQueue lengthro INTEGER .1.3.6.1.4.1.208.2.20.3.2.1.21 |
mplIfSpecific OBJECT IDENTIFIER .1.3.6.1.4.1.208.2.20.4 |
mplIfStackTableThis table contains information on the relationships
between the multiple sub-layers of network interfaces.
In particular, it contains information on which sub-
layers run 'on top of' which other sub-layers. Each
sub-layer corresponds to a conceptual row in the
ifTable. SEQUENCE OF MplIfStackEntry .1.3.6.1.4.1.208.2.20.4.1 |
mplIfStackEntryInformation on a particular relationship between two
sub-layers, specifying that one sub-layer runs on
'top' of the other sub-layer. Each sub-layer
corresponds to a conceptual row in the ifTable. MplIfStackEntry .1.3.6.1.4.1.208.2.20.4.1.1 |
mplIfStackNumberThe MP Link number. The MP Link number is the
same as the ifIndex for the corresponding
upper group in the MIB-2 ifGroup.ro INTEGER .1.3.6.1.4.1.208.2.20.4.1.1.1 |
mplIfStackLowerLayerThe value of ifIndex corresponding to the lower sub-
layer of the relationship, i.e., the sub-layer which
runs 'below' the sub-layer identified by the
corresponding instance of mplIfStackNumber. If
there is no lower sub-layer, then this object has the
value 0.ro INTEGER .1.3.6.1.4.1.208.2.20.4.1.1.2 |
mplGeneral OBJECT IDENTIFIER .1.3.6.1.4.1.208.2.20.5 |
mplGeneralOverviewChangeThe value of sysUpTime at the time any MP Link
seen from the overview changed state or the
like.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.208.2.20.5.1 |
mplGeneralIfgroupStatusA table describing the status of all ifgroups.
Bit 0-3: State: 001 = Up, 010 = Down, 011 = Timecut, 100 = Disabled
111 = Lock.
Bit 4: Reserved for future use
Bit 5: IP status: 1 = Up, 0 = Down.
(This bit is only used for MPLinks)
Bit 6: IPX status: 1 = Up, 0 = Down.
(This bit is only used for MPLinks)
Bit 7: Bridge status: 1 = Up, 0 = Down.
(This bit is only used for MPLinks)ro OCTET STRING .1.3.6.1.4.1.208.2.20.5.2 |
mplUtilization OBJECT IDENTIFIER .1.3.6.1.4.1.208.2.20.6 |
mplUtilizationTableUtilization table SEQUENCE OF MplUtilizationEntry .1.3.6.1.4.1.208.2.20.6.1 |
mplUtilizationEntry MplUtilizationEntry .1.3.6.1.4.1.208.2.20.6.1.1 |
mplUtilizationPlugNumberro INTEGER .1.3.6.1.4.1.208.2.20.6.1.1.1 |
mplUtilizationMplinkro INTEGER .1.3.6.1.4.1.208.2.20.6.1.1.2 |
mplUtilizationUserro UserEnum .1.3.6.1.4.1.208.2.20.6.1.1.3 |
mplUtilizationProtocolro ProtoEnum .1.3.6.1.4.1.208.2.20.6.1.1.4 |
mplUtilizationRxUtilro Counter .1.3.6.1.4.1.208.2.20.6.1.1.5 |
mplUtilizationTxUtilro Counter .1.3.6.1.4.1.208.2.20.6.1.1.6 |