IANA-MAU-TC-MIB
AI MIB Summary
The IANA-MAU-TC-MIB standardizes the textual conventions and enumerated type definitions for Ethernet Medium Attachment Unit (MAU) characteristics, specifically mapping `ifMauType` and `ifJackType` values to IANA-registered identifiers. This module enables network management systems to accurately interpret and monitor physical layer interface capabilities, connector types, and associated stack table dependencies across multi-vendor hardware.
This MIB module defines dot3MauType OBJECT-IDENTITIES and IANAifMauListBits and JackType Textual Conventions, specifying enumerated values of the ifMauTypeListBits and ifJackType objects respectively, defined in the MAU-MIB. A Standards Action (as defined in RFC 2434) is REQUIRED for the addition of the new MAU types, so that any prospective assignments are documented in an RFC. Any document that proposes such an addition is REQUIRED to note any special properties of the MAU types that it defines -- for example, side effects on the ifStackTable such as are noted in RFC 3636 Section 3.4.1 for 10GBASE-W MAUs.
Main OID:
ianaMauTC.1.3.6.1.2.1.26.7
55
Objects
Active
Status
2
Dependencies
Imported Objects
Objects
55 total| Object Name |
|---|
dot3MauType OBJECT IDENTIFIER .1.3.6.1.2.1.26.4 |
dot3MauTypeAUIno internal MAU, view from AUI OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.1 |
dot3MauType10Base5thick coax MAU OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.2 |
dot3MauTypeFoirlFOIRL MAU OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.3 |
dot3MauType10Base2thin coax MAU OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.4 |
dot3MauType10BaseTUTP MAU. Note that it is strongly recommended that agents return either dot3MauType10BaseTHD or dot3MauType10BaseTFD if the duplex mode is known. However, management applications should be prepared to receive this MAU type value from older agent implementations. OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.5 |
dot3MauType10BaseFPpassive fiber MAU OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.6 |
dot3MauType10BaseFBsync fiber MAU OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.7 |
dot3MauType10BaseFLasync fiber MAU. Note that it is strongly recommended that agents return either dot3MauType10BaseFLHD or dot3MauType10BaseFLFD if the duplex mode is known. However, management applications should be prepared to receive this MAU type value from older agent implementations. OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.8 |
dot3MauType10Broad36broadband DTE MAU. Note that 10BROAD36 MAUs can be attached to interfaces but not to repeaters. OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.9 |
dot3MauType10BaseTHDUTP MAU, half duplex mode OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.10 |
dot3MauType10BaseTFDUTP MAU, full duplex mode OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.11 |
dot3MauType10BaseFLHDasync fiber MAU, half duplex mode OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.12 |
dot3MauType10BaseFLFDasync fiber MAU, full duplex mode OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.13 |
dot3MauType100BaseT44 pair category 3 UTP OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.14 |
dot3MauType100BaseTXHD2 pair category 5 UTP, half duplex mode OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.15 |
dot3MauType100BaseTXFD2 pair category 5 UTP, full duplex mode OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.16 |
dot3MauType100BaseFXHDX fiber over PMT, half duplex mode OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.17 |
dot3MauType100BaseFXFDX fiber over PMT, full duplex mode OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.18 |
dot3MauType100BaseT2HD2 pair category 3 UTP, half duplex mode OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.19 |
dot3MauType100BaseT2FD2 pair category 3 UTP, full duplex mode OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.20 |
dot3MauType1000BaseXHDPCS/PMA, unknown PMD, half duplex mode OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.21 |
dot3MauType1000BaseXFDPCS/PMA, unknown PMD, full duplex mode OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.22 |
dot3MauType1000BaseLXHDFiber over long-wavelength laser, half duplex mode OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.23 |
dot3MauType1000BaseLXFDFiber over long-wavelength laser, full duplex mode OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.24 |
dot3MauType1000BaseSXHDFiber over short-wavelength laser, half duplex mode OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.25 |
dot3MauType1000BaseSXFDFiber over short-wavelength laser, full duplex mode OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.26 |
dot3MauType1000BaseCXHDCopper over 150-Ohm balanced cable, half duplex mode OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.27 |
dot3MauType1000BaseCXFDCopper over 150-Ohm balanced cable, full duplex mode OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.28 |
dot3MauType1000BaseTHDFour-pair Category 5 UTP, half duplex mode OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.29 |
dot3MauType1000BaseTFDFour-pair Category 5 UTP, full duplex mode OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.30 |
dot3MauType10GigBaseXX PCS/PMA, unknown PMD. OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.31 |
dot3MauType10GigBaseLX4X fiber over WWDM optics OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.32 |
dot3MauType10GigBaseRR PCS/PMA, unknown PMD. OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.33 |
dot3MauType10GigBaseERR fiber over 1550 nm optics OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.34 |
dot3MauType10GigBaseLRR fiber over 1310 nm optics OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.35 |
dot3MauType10GigBaseSRR fiber over 850 nm optics OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.36 |
dot3MauType10GigBaseWW PCS/PMA, unknown PMD. OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.37 |
dot3MauType10GigBaseEWW fiber over 1550 nm optics OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.38 |
dot3MauType10GigBaseLWW fiber over 1310 nm optics OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.39 |
dot3MauType10GigBaseSWW fiber over 850 nm optics OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.40 |
dot3MauType10GigBaseCX4X copper over 8 pair 100-Ohm balanced cable OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.41 |
dot3MauType2BaseTLVoice grade UTP copper, up to 2700m OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.42 |
dot3MauType10PassTSVoice grade UTP copper, up to 750m OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.43 |
dot3MauType100BaseBX10DOne single-mode fiber OLT OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.44 |
dot3MauType100BaseBX10UOne single-mode fiber ONU OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.45 |
dot3MauType100BaseLX10Two fiber OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.46 |
dot3MauType1000BaseBX10DOne single-mode fiber OLT OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.47 |
dot3MauType1000BaseBX10UOne single-mode fiber ONU OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.48 |
dot3MauType1000BaseLX10Two fiber 10km OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.49 |
dot3MauType1000BasePX10DOne single-mode fiber OMP OLT 10km OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.50 |
dot3MauType1000BasePX10UOne single-mode fiber OMP ONU 10km OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.51 |
dot3MauType1000BasePX20DOne single-mode fiber OMP OLT 20km OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.52 |
dot3MauType1000BasePX20UOne single-mode fiber OMP ONU 20km OBJECT IDENTIFIER .1.3.6.1.2.1.26.4.53 |
ianaMauTCThis MIB module defines dot3MauType OBJECT-IDENTITIES and IANAifMauListBits and JackType Textual Conventions, specifying enumerated values of the ifMauTypeListBits and ifJackType objects respectively, defined in the MAU-MIB. A Standards Action (as defined in RFC 2434) is REQUIRED for the addition of the new MAU types, so that any prospective assignments are documented in an RFC. Any document that proposes such an addition is REQUIRED to note any special properties of the MAU types that it defines -- for example, side effects on the ifStackTable such as are noted in RFC 3636 Section 3.4.1 for 10GBASE-W MAUs. MODULE-IDENTITY .1.3.6.1.2.1.26.7 |