HPN-ICF-POWER-ETH-EXT-MIB
Description.
Main OID:
hpnicfPowerEthernetExt.1.3.6.1.4.1.11.2.14.11.15.2.14
129
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
129 total| Object Name |
|---|
hpnicfPowerEthernetExtDescription. MODULE-IDENTITY .1.3.6.1.4.1.11.2.14.11.15.2.14 |
hpnicfPsePortTableThe indexing scheme is taken form that used by the IETF Power MIB. The same indexing scheme is used to give continuity in behaviour between that standard and this extensions definitioin. SEQUENCE OF HpnicfPsePortEntry .1.3.6.1.4.1.11.2.14.11.15.2.14.1 |
hpnicfPsePortEntryThe pethPsePortGroupIndex is imported from the IETF Power MIB and uniquely identifies the group containing the port to which power ethernet PSE is connected. Group means (box in the stack, module in a rack). The pethPsePortPowerIndex is imported from the IETF Power MIB and uniquely identifies the power ethernet PSE port within group pethPseGroupIndex to which the power Ethernet PSE entry is connected. This value will match the local port number on a switch. HpnicfPsePortEntry .1.3.6.1.4.1.11.2.14.11.15.2.14.1.1 |
hpnicfPsePortFaultDescriptionThe object supports the fault category of the IETF Power MIB [1] pethPsePortDetectionStatus object. A textual description containing more information about the nature of this fault is provided by this object. Typically this will detail the precise PoE hardware state which is causing the pethPsePortDetectionStatus object to be in the 'fault' state. It is a DisplayString of up to 255 characters.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.14.1.1.2 |
hpnicfPsePortPeakPowerThe object specifies the peak power which has been consumed by the port. It is defined as the highest measured value of power in milliWatts that has been consumed by the port. Its value is only reset when link is lost, the port is PoE disabled or when it is manually reset by the user asspecified below. It is a read/write integer value with units of milliWatts. Writing a value of zero to this object resets its value to zero. Writing any other value to this object has no effect on its value and an error is returned.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.14.1.1.3 |
hpnicfPsePortAveragePowerThe object specifies the average power which has been consumed by the port. This object is a read/write integer value with units of milliWatts. Writing a value of zero to this object resets its value to zero. Writing any other value to this object has no effect on its value and an error is returned.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.14.1.1.4 |
hpnicfPsePortCurrentPowerThe object specifies the power currently being consumed by the port. It is a read only integer value with units of milliWatts.ro Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.14.1.1.5 |
hpnicfPsePortPowerLimitThe object specifies the power limit set for this port. The PSE will not supply more than this level of power to the specified port. It is a read/write integer value with units of milliWatts.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.14.1.1.6 |
hpnicfPsePortProfileIndexIndicates the power profile which is currently associated with this port. This object references the corresponding hpnicfPseProfileIndex object in the power profiles table. A value of zero is a special case and indicates that no power profile is currently associated with this port. When hpnicfPseProfileIndex is set to an index of existent profile, pethPsePortPowerPairs, pethPsePortPowerPriority, pethPsePortAdminEnable and hpnicfPsePortPowerLimit will be set to the same as corresponding value. PethPsePortPowerPairs, pethPsePortPowerPriority and pethPsePortAdminEnable are objects of rfc3621-Power-Ethernet.mib.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.14.1.1.7 |
hpnicfMainPseTableDescription. SEQUENCE OF HpnicfMainPseEntry .1.3.6.1.4.1.11.2.14.11.15.2.14.2 |
hpnicfMainPseEntryThe pethMainPseGroupIndex is imported from the IETF Power MIB and uniquely identifies the group containing the port to which power ethernet PSE is connected. Group means (box in the stack, module in a rack) and the value 1 MUST be used for non-modular devices. HpnicfMainPseEntry .1.3.6.1.4.1.11.2.14.11.15.2.14.2.1 |
hpnicfMainPsePowerLimitThe object specifies the power limit set for the unit as a whole. The PoE unit will already have a nominal power defined by the IETF Power MIB [1] pethMainPsePower object. This OPTIONAL object specifies a further limit to this nominal power value. This may be useful to control the thermals of the unit, or for internal testing purposes. One possible use for this object may be to lower the power consumption of the unit if one or more of the internal fans have broken. It is a read/write integer value with units of Watts (note - Watts is chosen instead of milliWatts here since the IETF Power MIB [1] measures unit based parameters, such as the pethMainPsePower object, in units of Watts).rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.14.2.1.1 |
hpnicfMainPseAveragePowerThe object specifies the average power which has been consumed by the port. It is a read/write integer value with units of Watts (note - Watts is chosen instead of milliWatts here since the IETF Power MIB [1] measures unit based parameters, such as the pethMainPsePower object, in units of Watts). Writing a value of zero to this object resets its value to zero. Writing any other value to this object has no effect on its value and an error is returned.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.14.2.1.2 |
hpnicfMainPsePeakPowerThe object specifies the peak power which has been consumed for PoE. It is defined as the highest measured value of power in milliWatts that has been consumed at any one point in time by the sum of the PoE ports. Its value is only reset when the unit is powered on or when it is manually reset by the user as specifiedbelow. It is a read/write integer value with units of Watts (note - Watts is chosen instead of milliWatts here since the IETF Power MIB [1] measures unit based parameters, such as the pethMainPsePower object, in units of Watts). Writing a value of zero to this object resets its value to zero. Writing any other value to this object has noeffect on its value and an error is returned.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.14.2.1.3 |
hpnicfMainGuaranteedPowerRemainingThe object specifies the amount of power remaining in the guaranteed power pool. Each time a port is placed into guaranteed mode it reserves a set amount of power out of the total guaranteed power pool for the system. This intention of this object is to give the client of this MIB (whether that be the CLI or the Web interface or the end user) an indication of how many ports can still be placed into guaranteed mode. It is a read only integer value with units of Watts(note - Watts is chosen instead of milliWatts here since the IETF Power MIB [1] measures unit based parameters,such as the pethMainPsePower object, in units of Watts).ro Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.14.2.1.4 |
hpnicfMainPsePriorityModeDescribes or controls the priority mode on slot which must be enabled firstly. When a new board is inserted, and the power is over-load, a value of disconnection(0) means that the power will stop supply to the low priority slot ; A value of non-disconnection(1) means that the slot still supply when a new board is inserted, and the power is over-load too.rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.14.2.1.5 |
hpnicfMainPseLegacyDescribes or controls the legacy mode on slot which must be enabled firstly. Legacy mode: standard or nonstandard PD detection mode.rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.14.2.1.6 |
hpnicfMainPsePowerPriorityDescribes or controls the priority of the PSE. The priority will be used by the PSE policy to prevent from power overloading. If the priority of PSE is set to critical, the PSE will turn into guaranteed mode. The priority could be used by a control mechanism that prevents power overloading by disconnecting PSEs with lower power priority. PSEs that connect devices critical to the application should be set to higher priority.rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.14.2.1.7 |
hpnicfPseAutoDetectActiveThe object specifies whether the device auto-detection feature is active. If this object is set to Active, and a known powered device is detected, then the port will automatically switch to Auto-Guaranteed mode. This is a stackwide object (ie. it is not referenced by group index).rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.14.3 |
hpnicfPseComformance OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.14.4 |
hpnicfPseCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.14.4.1 |
hpnicfPseComplianceDescription. Unknown .1.3.6.1.4.1.11.2.14.11.15.2.14.4.1.1 |
hpnicfPseGroup OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.14.4.2 |
hpnicfPsePortGroupA collection of objects should be supported at the same time. Unknown .1.3.6.1.4.1.11.2.14.11.15.2.14.4.2.1 |
hpnicfMainPseGroupA collection of objects should be supported at the same time. Unknown .1.3.6.1.4.1.11.2.14.11.15.2.14.4.2.2 |
hpnicfPseScalarGroupA collection of scalar objects supported. Unknown .1.3.6.1.4.1.11.2.14.11.15.2.14.4.2.3 |
hpnicfPsePDNotificationGroupPD Change Notification. Unknown .1.3.6.1.4.1.11.2.14.11.15.2.14.4.2.4 |
hpnicfPseProfilesGroupA collection of objects should be supported at the same time. Unknown .1.3.6.1.4.1.11.2.14.11.15.2.14.4.2.5 |
hpnicfPOEPowerThresholdLimitGroupPower threshold limits group. Unknown .1.3.6.1.4.1.11.2.14.11.15.2.14.4.2.6 |
hpnicfPOEPowerSupInfoGroupThe basic Power information group. Unknown .1.3.6.1.4.1.11.2.14.11.15.2.14.4.2.7 |
hpnicfPOEPowerDCOutStateGroupThe DC out power state group. Unknown .1.3.6.1.4.1.11.2.14.11.15.2.14.4.2.8 |
hpnicfPOEPowerDCOutInfoGroupThe power AC input switch information group Unknown .1.3.6.1.4.1.11.2.14.11.15.2.14.4.2.9 |
hpnicfPOEPowerACSwitchStateModuleGroupPD Change Notification. Unknown .1.3.6.1.4.1.11.2.14.11.15.2.14.4.2.10 |
hpnicfPOEPowerInCurStateGroupPD Change Notification. Unknown .1.3.6.1.4.1.11.2.14.11.15.2.14.4.2.11 |
hpnicfPOEPowerAlarmStateGroupPD Change Notification. Unknown .1.3.6.1.4.1.11.2.14.11.15.2.14.4.2.12 |
hpnicfPsePowerMaxValueThe object specifies the max poe power for lanswitch. The value should between the power currently and the max power.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.14.5 |
hpnicfpseportNotification OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.14.6 |
hpnicfpsePDChangeNotificationThis notification indicates if PD has been inserted or pulled out. NOTIFICATION-TYPE .1.3.6.1.4.1.11.2.14.11.15.2.14.6.1 |
hpnicfPOEDisconnectNotificationThis notification indicates the POE power module does not disconnect. NOTIFICATION-TYPE .1.3.6.1.4.1.11.2.14.11.15.2.14.6.2 |
hpnicfPOEInputErrorNotificationThis notification indicates the POE power module input error. NOTIFICATION-TYPE .1.3.6.1.4.1.11.2.14.11.15.2.14.6.3 |
hpnicfPOEOutputErrorNotificationThis notification indicates the POE power module output error. NOTIFICATION-TYPE .1.3.6.1.4.1.11.2.14.11.15.2.14.6.4 |
hpnicfPOEOverVoltageNotificationThis notification indicates the POE power module overruns the voltage limit. NOTIFICATION-TYPE .1.3.6.1.4.1.11.2.14.11.15.2.14.6.5 |
hpnicfPOEOverTempNotificationThis notification indicates the POE power module overruns the temperature limit. NOTIFICATION-TYPE .1.3.6.1.4.1.11.2.14.11.15.2.14.6.6 |
hpnicfPOEFanErrorNotificationThis notification indicates the POE power module fan error. NOTIFICATION-TYPE .1.3.6.1.4.1.11.2.14.11.15.2.14.6.7 |
hpnicfPOEModuleShutdownNotificationThis notification indicates the POE power module is closed. NOTIFICATION-TYPE .1.3.6.1.4.1.11.2.14.11.15.2.14.6.8 |
hpnicfPOECurRestrictedNotificationThis notification indicates the POE power module current is restricted. NOTIFICATION-TYPE .1.3.6.1.4.1.11.2.14.11.15.2.14.6.9 |
hpnicfPOEACSwitchNotificationThis notification indicates the AC input switch alarm of this POE power. NOTIFICATION-TYPE .1.3.6.1.4.1.11.2.14.11.15.2.14.6.10 |
hpnicfPOEACInCurANotificationThis notification indicates the AC input current A alarm state of this POE power. NOTIFICATION-TYPE .1.3.6.1.4.1.11.2.14.11.15.2.14.6.11 |
hpnicfPOEACInCurBNotificationThis notification indicates the AC input current B alarm state of this POE power. NOTIFICATION-TYPE .1.3.6.1.4.1.11.2.14.11.15.2.14.6.12 |
hpnicfPOEACInCurCNotificationThis notification indicates the AC input current C alarm state of this POE power. NOTIFICATION-TYPE .1.3.6.1.4.1.11.2.14.11.15.2.14.6.13 |
hpnicfPOEACSwitchVolABNotificationThis notification indicates the AC input voltage AB alarm state of this POE power. NOTIFICATION-TYPE .1.3.6.1.4.1.11.2.14.11.15.2.14.6.14 |
hpnicfPOEACSwitchVolBCNotificationThis notification indicates the AC input voltage BC alarm state of this POE power. NOTIFICATION-TYPE .1.3.6.1.4.1.11.2.14.11.15.2.14.6.15 |
hpnicfPOEACSwitchVolCANotificationThis notification indicates the AC input voltage CA alarm state of this POE power. NOTIFICATION-TYPE .1.3.6.1.4.1.11.2.14.11.15.2.14.6.16 |
hpnicfPOEDCOutVolNotificationThis notification indicates the DC output alarm of this POE power. NOTIFICATION-TYPE .1.3.6.1.4.1.11.2.14.11.15.2.14.6.17 |
hpnicfPOEShutdownNotificationThis notification indicates the whole POE power has been shutdown. NOTIFICATION-TYPE .1.3.6.1.4.1.11.2.14.11.15.2.14.6.18 |
hpnicfPseProfilesTableA table of objects representing a set of power profiles. Power profiles can be applied to PoE ports, which have the effect of automatically setting the priority, power limit and PoE enable MIB objects to the values specified in the power profile. SEQUENCE OF HpnicfPseProfilesEntry .1.3.6.1.4.1.11.2.14.11.15.2.14.7 |
hpnicfPseProfilesEntryA set of objects that display and control the Main power of a PSE. HpnicfPseProfilesEntry .1.3.6.1.4.1.11.2.14.11.15.2.14.7.1 |
hpnicfPseProfileIndexThe index of the profile. This uniquely allow the profile to be identified. Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.14.7.1.1 |
hpnicfPseProfileNameAssigns the profile a name with which the settings can be assiciated with. For example, 'NBX Phone'.rw DisplayString .1.3.6.1.4.1.11.2.14.11.15.2.14.7.1.2 |
hpnicfPseProfilePowerModeThe power mode associated with this power profile. There are two possible power modes as follows: powerDisabled, powerEnabled. When a power profile is applied to a PSE port, this value dictates the settings of the ports pethPsePortPowerPriority and pethPsePortAdminEnable objects.rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.14.7.1.3 |
hpnicfPseProfilePowerLimitThe power limit to be applied to the ports hpnicfPsePortPowerLimit object when the profile is applied to the PSE port. Expressed in milliWatts.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.14.7.1.4 |
hpnicfPseProfilePriorityThis object controls the priority of the port from the point of view of a power management algorithm. The priority that is set by this variable could be used by a control mechanism that prevents over current situations by disconnecting first ports with lower power priority. Ports that connect devices critical to the operation of the network - like the E911 telephones ports - should be set to higher priority.rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.14.7.1.5 |
hpnicfPseProfilePairsDescribes or controls the pairs in use. If the value of pethPsePortPowerPairsControl is true, this object is writable. A value of signal(1) means that the signal pairs only are in use. A value of spare(2) means that the spare pairs only are in use.rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.14.7.1.6 |
hpnicfPseProfileApplyNumThe number of this profile which has been applied. If hpnicfPseProfileApplyNum is not zero, user can't change the current line.ro Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.14.7.1.7 |
hpnicfPseProfileRowStatusThe status of this classifier. If hpnicfPseProfileApplyNum is not zero, user can't delete the current line.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.14.7.1.8 |
hpnicfPOEPowerObjects OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.14.8 |
hpnicfPOEThresholdLimitObjs OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.14.8.1 |
hpnicfPOEThresholdACMimimumInput threshold AC minimum. It is a read-write node. The value of this node is 'OCTET STRING', it is used to describe a float value. So this string should fit the following rule: 1. This string should be terminated by '\0'; 2. Every characters should be number or radix point; 3. The radix point should occur only once, and it should not be the first or the last character of the string. The value of this node should be smaller than 264.0V and larger than 90.0V. And it should be smaller than the hpnicfPOEThresholdACMaximum.rw OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.14.8.1.1 |
hpnicfPOEThresholdACMaximumInput threshold AC maximum. It is a read-write node. The value of this node is 'OCTET STRING', it is used to describe a float value. So this string should fit the following rule: 1. This string should be terminated by '\0'; 2. Every characters should be number or radix point; 3. The radix point should occur only once, and it should not be the first or the last character of the string. It should be smaller than 264.0V and larger than 90.0V. And it should be larger than the hpnicfPOEThresholdACMinimum.rw OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.14.8.1.2 |
hpnicfPOEThresholdDCMinimumInput threshold DC minimum. It is a read-write node. The value of this node is 'OCTET STRING', it is used to describe a float value. So this string should fit the following rule: 1. This string should be terminated by '\0'; 2. Every characters should be number or radix point; 3. The radix point should occur only once, and it should not be the first or the last character of the string. It should be smaller than 47.0V and larger than 45.0V.rw OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.14.8.1.3 |
hpnicfPOEThresholdDCMaximumInput threshold DC maximum. It is a read-write node. The value of this node is 'OCTET STRING', it is used to describe a float value. So this string should fit the following rule: 1. This string should be terminated by '\0'; 2. Every characters should be number or radix point; 3. The radix point should occur only once, and it should not be the first or the last character of the string. It should be smaller than 57.0V and larger than 55.0V.rw OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.14.8.1.4 |
hpnicfPOESupModuleInfoObjs OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.14.8.2 |
hpnicfPOEPowerTypeThe type of the power.ro OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.14.8.2.1 |
hpnicfPOEPowerModuleNumThe number of the power modules.ro Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.14.8.2.2 |
hpnicfPOESupervisionModuleNameThe object specifies the Supervision Module name on this POE power.ro OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.14.8.2.3 |
hpnicfPOESMMajorVersionThe object specifies the high byte of the monitor module version.ro Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.14.8.2.4 |
hpnicfPOESMMinorVersionThe object specifies the low byte of the monitor module version.ro Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.14.8.2.5 |
hpnicfPOESMFactorNameThe object specifies the name of the manufactor.ro OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.14.8.2.6 |
hpnicfPOEModuleInfoTableThe table of the module information on this POE power. SEQUENCE OF HpnicfPOEModuleInfoEntry .1.3.6.1.4.1.11.2.14.11.15.2.14.8.2.7 |
hpnicfPOEModuleInfoEntryThe entry of the module information on this POE power. HpnicfPOEModuleInfoEntry .1.3.6.1.4.1.11.2.14.11.15.2.14.8.2.7.1 |
hpnicfPOEModuleIndexThe index of the current module on this POE power. It is also the index of hpnicfPOEModuleInfoTable. The range of this node is from 1 to hpnicfPOEPowerModuleNum.ro Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.14.8.2.7.1.1 |
hpnicfPOEModuleIDThe ID of the current module on this POE power.ro Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.14.8.2.7.1.2 |
hpnicfPOEModuleInfoPowerThe power of the current module on this POE power.ro Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.14.8.2.7.1.3 |
hpnicfPOEModuleHardVerInfoThe hardware version information of the current module on this POE power.ro OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.14.8.2.7.1.4 |
hpnicfPOEDCOutStateObjects OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.14.8.3 |
hpnicfPOEDCOutStateModuleNumThe module number on this POE power. It is the maximum of the hpnicfPOEDCOutStateIndex.ro Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.14.8.3.1 |
hpnicfPOEDCOutStateTableThe table of DC output power state on this POE power. SEQUENCE OF HpnicfPOEDCOutStateEntry .1.3.6.1.4.1.11.2.14.11.15.2.14.8.3.2 |
hpnicfPOEDCOutStateEntryThe entry of the DC output power state on this POE power. HpnicfPOEDCOutStateEntry .1.3.6.1.4.1.11.2.14.11.15.2.14.8.3.2.1 |
hpnicfPOEDCOutStateIndexThe index of the DC output power state on this POE power. The range of this node is from 1 to hpnicfPOEDCOutStateModuleNum.ro Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.14.8.3.2.1.1 |
hpnicfPOEDCOutDCVolAlarmThe DC output alarm of the DC output power state on this POE power. The value of this node will be the following values: normal (1), underLimit (2), aboveLimit (3), fuseBroken (4), switchOff (5), otherError (6).ro DCAlarmState .1.3.6.1.4.1.11.2.14.11.15.2.14.8.3.2.1.2 |
hpnicfPOEDCOutInfoObjects OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.14.8.4 |
hpnicfPOEDCOutCurNumThe number of DC output current on this POE power. It is the maximum of hpnicfPOEDCOutInfoIndex.ro Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.14.8.4.1 |
hpnicfPOEDCOutInfoTableThe table of the DC output information on this POE power. SEQUENCE OF HpnicfPOEDCOutInfoEntry .1.3.6.1.4.1.11.2.14.11.15.2.14.8.4.2 |
hpnicfPOEDCOutInfoEntryThe entry of the DC output information on this POE power. HpnicfPOEDCOutInfoEntry .1.3.6.1.4.1.11.2.14.11.15.2.14.8.4.2.1 |
hpnicfPOEDCOutInfoIndexThe index of the DC output information on this POE POWER. The range of this node is from 1 to hpnicfPOEDCOutCurNum.ro Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.14.8.4.2.1.1 |
hpnicfPOEDCOutVolThe DC output voltage of the current DC output on this POE power.ro OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.14.8.4.2.1.2 |
hpnicfPOEDCOutInfoLoadCurThe total load current of the current DC output on this POE power.ro OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.14.8.4.2.1.3 |
hpnicfPOEACSwitchStateModuleObjs OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.14.8.5 |
hpnicfPOEACSwitchStateModuleNumThe number of the AC swtich state module on this POE power. It is the maximum of hpnicfPOEACSwitchStateIndex.ro Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.14.8.5.1 |
hpnicfPOEACSwitchStateTableThe table of the AC switch state on this POE power. SEQUENCE OF HpnicfPOEACSwitchStateEntry .1.3.6.1.4.1.11.2.14.11.15.2.14.8.5.2 |
hpnicfPOEACSwitchStateEntryThe entry of the AC switch state on this POE power. HpnicfPOEACSwitchStateEntry .1.3.6.1.4.1.11.2.14.11.15.2.14.8.5.2.1 |
hpnicfPOEACSwitchStateIndexThe index of the AC switch state on this POE power. The range of this node is from 1 to hpnicfPOEACSwitchStateModuleNum.ro Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.14.8.5.2.1.1 |
hpnicfPOEACSwitchStateThe AC switch state on this POE power. The value of this node will be one of the following values: on (1), off (2), highVoltInput (3), lowVoltInput (4)ro SwitchState .1.3.6.1.4.1.11.2.14.11.15.2.14.8.5.2.1.2 |
hpnicfPOEInCurStateObjects OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.14.8.6 |
hpnicfPOEInCurStateModuleNumThe DC input current state of the module on this POE power. It is the maximum of the hpnicfPOESwitchStateVolExIndex.ro Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.14.8.6.1 |
hpnicfPOEInCurAStateThe current A state in the DC input on this POE power. normal (1), underLimit (2), aboveLimit (3), lackPhrase (4), fuseBroken (5), switchOff (6), otherError (7).ro ACAlarmState .1.3.6.1.4.1.11.2.14.11.15.2.14.8.6.2 |
hpnicfPOEInCurBStateThe current B state in the DC input on this POE power. The value of this node will be one of the following values: normal (1), underLimit (2), aboveLimit (3), lackPhrase (4), fuseBroken (5), switchOff (6), otherError (7).ro ACAlarmState .1.3.6.1.4.1.11.2.14.11.15.2.14.8.6.3 |
hpnicfPOEInCurCStateThe current C state in the DC input on this POE power. The value of this node will be one of the following values: normal (1), underLimit (2), aboveLimit (3), lackPhrase (4), fuseBroken (5), switchOff (6), otherError (7).ro ACAlarmState .1.3.6.1.4.1.11.2.14.11.15.2.14.8.6.4 |
hpnicfPOESwitchStateVolExTableAll alarm status of the VOL status. The value of this node will be one of the following values: normal (1), underLimit (2), aboveLimit (3), lackPhrase (4), fuseBroken (5), switchOff (6), otherError (7). SEQUENCE OF HpnicfPOESwitchStateVolExEntry .1.3.6.1.4.1.11.2.14.11.15.2.14.8.6.5 |
hpnicfPOESwitchStateVolExEntryThe hpnicfPOESwitchStateVolExIndex will match the number of the VOL status. HpnicfPOESwitchStateVolExEntry .1.3.6.1.4.1.11.2.14.11.15.2.14.8.6.5.1 |
hpnicfPOESwitchStateVolExIndexThe object species the index of the VOL status. The range of this node is from 1 to hpnicfPOEInCurStateModuleNum.ro Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.14.8.6.5.1.1 |
hpnicfPOESwitchStateInVolABThe object specifies the VOL AB alarm in each VOL status. The value of this node will be one of the following values: normal (1), underLimit (2), aboveLimit (3), lackPhrase (4), fuseBroken (5), switchOff (6), otherError (7).ro ACAlarmState .1.3.6.1.4.1.11.2.14.11.15.2.14.8.6.5.1.2 |
hpnicfPOESwitchStateInVolBCThe object specifies the VOL BC alarm in each VOL status. The value of this node will be one of the following values: normal (1), underLimit (2), aboveLimit (3), lackPhrase (4), fuseBroken (5), switchOff (6), otherError (7).ro ACAlarmState .1.3.6.1.4.1.11.2.14.11.15.2.14.8.6.5.1.3 |
hpnicfPOESwitchStateInVolCAThe object specifies the VOL CA alarm in each VOL status. The value of this node will be one of the following values: normal (1), underLimit (2), aboveLimit (3), lackPhrase (4), fuseBroken (5), switchOff (6), otherError (7).ro ACAlarmState .1.3.6.1.4.1.11.2.14.11.15.2.14.8.6.5.1.4 |
hpnicfPOEAlarmStateObjects OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.14.8.7 |
hpnicfPOEAlarmStateModuleNumThe object specifies the number of the power modules in alarm state.ro Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.14.8.7.1 |
hpnicfPOEAlarmStateInfoTableAll alarm states in the POE power modules. SEQUENCE OF HpnicfPOEAlarmStateInfoEntry .1.3.6.1.4.1.11.2.14.11.15.2.14.8.7.2 |
hpnicfPOEAlarmStateInfoEntryThe hpnicfPOEAlarmModuleInfoIndex will match the number of the power module. HpnicfPOEAlarmStateInfoEntry .1.3.6.1.4.1.11.2.14.11.15.2.14.8.7.2.1 |
hpnicfPOEAlarmModuleInfoIndexThe index specifies the index of the HpnicfPOEAlarmStateInfoEntry table. The range of this node is from 1 to hpnicfPOEAlarmStateModuleNum.ro Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.14.8.7.2.1.1 |
hpnicfPOEModuleDisconnectThe node specifies the alarm state: The module does not link. The value of this node is one of the following values: normal (1), alarm (2).ro ModuleAlarmState .1.3.6.1.4.1.11.2.14.11.15.2.14.8.7.2.1.2 |
hpnicfPOEModuleInputErrorThe node specifies the alarm state: Input error. The value of this node is one of the following values: normal (1), alarm (2).ro ModuleAlarmState .1.3.6.1.4.1.11.2.14.11.15.2.14.8.7.2.1.3 |
hpnicfPOEModuleOutputErrorThe node specifies the alarm state: Output error. The value of this node is one of the following values: normal (1), alarm (2).ro ModuleAlarmState .1.3.6.1.4.1.11.2.14.11.15.2.14.8.7.2.1.4 |
hpnicfPOEModuleOverVoltageThe node specifies the alarm state: The voltage is too high. The value of this node is one of the following values: normal (1), alarm (2).ro ModuleAlarmState .1.3.6.1.4.1.11.2.14.11.15.2.14.8.7.2.1.5 |
hpnicfPOEModuleOverTempThe node specifies the alarm state: The temperature is too high. The value of this node is one of the following values: normal (1), alarm (2).ro ModuleAlarmState .1.3.6.1.4.1.11.2.14.11.15.2.14.8.7.2.1.6 |
hpnicfPOEModuleFanErrorThe node specifies the alarm state: The fan error. The value of this node is one of the following values: normal (1), alarm (2).ro ModuleAlarmState .1.3.6.1.4.1.11.2.14.11.15.2.14.8.7.2.1.7 |
hpnicfPOEModuleShutdownThe node specifies the alarm state: The module is shutdown. The value of this node is one of the following values: normal (1), alarm (2).ro ModuleAlarmState .1.3.6.1.4.1.11.2.14.11.15.2.14.8.7.2.1.8 |
hpnicfPOEModuleCurRestrictedThe node specifies the alarm state: The module limit the current. The value of this node is one of the following values: normal (1), alarm (2).ro ModuleAlarmState .1.3.6.1.4.1.11.2.14.11.15.2.14.8.7.2.1.9 |
hpnicfPsePolicyModeThe PSE policy only applies to the situation that when a new board (PSE) is inserted, and the power is overload. A value of priority(2) means that the power will stop supplying to the low priority PSE. About PSE priority, please refer to hpnicfMainPsePowerPriority. A value of disabled(1) means that the power will stop supplying to the new inserted PSE. The default value of this object is disabled(1).rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.14.9 |
hpnicfPDPolicyModeThe PD policy only applies to the situation that when a new PD is inserted, and the power of PSE is overload. A value of priority(2) means that the power will stop supplying to the low priority port PD. About port priority, please refer to pethPsePortPowerPriority. A value of disabled(1) means that the slot stop supplying to the new inserted PD. The default value of this object is disabled(1).rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.14.10 |