HPN-ICF-LI-MIB
Lawful Interception MIB
Main OID:
hpnicfLI.1.3.6.1.4.1.11.2.14.11.15.2.111
71
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
71 total| Object Name |
|---|
hpnicfLILawful Interception MIB MODULE-IDENTITY .1.3.6.1.4.1.11.2.14.11.15.2.111 |
hpnicfLICommon OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.111.1 |
hpnicfLITrapBindObjects OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.111.1.1 |
hpnicfLIBoardInformationIt is a slot number.ro Unsigned32 .1.3.6.1.4.1.11.2.14.11.15.2.111.1.1.1 |
hpnicfLINotifications OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.111.1.2 |
hpnicfLINotificationsPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.111.1.2.0 |
hpnicfLIActiveThis Notification is sent when a type of intercepting configuration is changed from inactive to active. The value of the hpnicfLIStreamtype which identify the actual intercept stream is included in this notification. NOTIFICATION-TYPE .1.3.6.1.4.1.11.2.14.11.15.2.111.1.2.0.1 |
hpnicfLITimeOutWhen the time specified in hpnicfLIMediationTimeout arrives, the device notifies the manager corresponding intercept is removed. NOTIFICATION-TYPE .1.3.6.1.4.1.11.2.14.11.15.2.111.1.2.0.2 |
hpnicfLIFailureInformationWhen interception is configured on distributed device, the configuration perhaps failed on some board. If this happened, this notification will occur. NOTIFICATION-TYPE .1.3.6.1.4.1.11.2.14.11.15.2.111.1.2.0.3 |
hpnicfLIObjects OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.111.1.3 |
hpnicfLINewIndexThis object will be used as an index value for a new hpnicfLIMediationEntry. Whenever read, the agent will give a non-used value. This is to reduce the probability of conflict during creation of new hpnicfLIMediationTable entries.ro Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.111.1.3.1 |
hpnicfLIMediationTableThis table describes interception gateway information with which interception device communicates. SEQUENCE OF HpnicfLIMediationEntry .1.3.6.1.4.1.11.2.14.11.15.2.111.1.3.2 |
hpnicfLIMediationEntryAn entry of configuring mediation device. HpnicfLIMediationEntry .1.3.6.1.4.1.11.2.14.11.15.2.111.1.3.2.1 |
hpnicfLIMediationIndexhpnicfLIMediationIndex is a entry identifier. The Mediation Device should be responsible for making sure these are unique. Before creating a new entry, a value for this variable may be obtained by reading hpnicfLINewIndex to reduce the probability of a value collision. Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.111.1.3.2.1.1 |
hpnicfLIMediationDestAddrTypeThe type of hpnicfLIMediationDestAddr.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.111.1.3.2.1.2 |
hpnicfLIMediationDestAddrThe IP Address of the Mediation Device to receive intercepted traffic.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.111.1.3.2.1.3 |
hpnicfLIMediationDestPortThe L4-port number on the Mediation Device to receive intercepted traffic.rw InetPortNumber (INET-ADDRESS-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.111.1.3.2.1.4 |
hpnicfLIMediationSrcInterfaceThe interface on the intercepting device from which to transmit intercepted data. If zero, intercepting device will select an outbound interface according to hpnicfLIMediationDestAddr.rw InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.111.1.3.2.1.5 |
hpnicfLIMediationDscpThe Differentiated Services Code Point the intercepting device applies to the IP packets encapsulating the intercepted traffic.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.111.1.3.2.1.6 |
hpnicfLIMediationTimeOutThe time at which this row and all related Stream Table rows should be automatically removed, and the intercept function expire.rw DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.111.1.3.2.1.7 |
hpnicfLIMediationTransportThe protocol used in transferring intercepted data to the Mediation Device.rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.111.1.3.2.1.8 |
hpnicfLIMediationNotificationEnableThis variable controls the generation of any notifications or informs by the MIB agent for this table entry.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.111.1.3.2.1.9 |
hpnicfLIMediationRowStatusOperation status of this table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.111.1.3.2.1.10 |
hpnicfLIStreamTableThis table lists the traffic stream's type to be intercepted. The specified filter is defined in hpnicfLIIPStreamTable, hpnicfLIMACStreamTable or hpnicfLIUserStreamTable, according to hpnicfLIStreamtype. Also it contains counters for packets to be intercepted and dropped by attached type of filter. SEQUENCE OF HpnicfLIStreamEntry .1.3.6.1.4.1.11.2.14.11.15.2.111.1.3.3 |
hpnicfLIStreamEntryA single type of data stream to be intercepted. HpnicfLIStreamEntry .1.3.6.1.4.1.11.2.14.11.15.2.111.1.3.3.1 |
hpnicfLIStreamIndexThe index of the stream entry. Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.111.1.3.3.1.1 |
hpnicfLIStreamtypeIdentifies the type of stream, and according to it uses filter table. It can not be changed after a filter table is attached to it. The following types of streams are supported: ip: IP filter. The exact definition is a row in hpnicfLIIPStreamTable. mac: MAC filter. The exact definition is a row in hpnicfLIMACStreamTable. userConnecton: User connection filter. The exact definition is a row in hpnicfLIUserStreamTable.rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.111.1.3.3.1.2 |
hpnicfLIStreamEnableIf 'true', the interception is active. And it is set to 'true' only after an additional filter specification has been attached to this stream.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.111.1.3.3.1.3 |
hpnicfLIStreamPacketsThe numbers of packets that have been intercepted.ro Counter32 .1.3.6.1.4.1.11.2.14.11.15.2.111.1.3.3.1.4 |
hpnicfLIStreamDropsThe numbers of packets were dropped in the lawful intercept process.ro Counter32 .1.3.6.1.4.1.11.2.14.11.15.2.111.1.3.3.1.5 |
hpnicfLIStreamHPacketsThe numbers of packets have been intercepted. This object is a 64-bit version of hpnicfLIStreamPackets.ro Counter64 .1.3.6.1.4.1.11.2.14.11.15.2.111.1.3.3.1.6 |
hpnicfLIStreamHDropsThe numbers of packets were dropped in the lawful intercept process. This object is a 64-bit version of hpnicfLIStreamDrops.ro Counter64 .1.3.6.1.4.1.11.2.14.11.15.2.111.1.3.3.1.7 |
hpnicfLIStreamRowStatusOperation status of this table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.111.1.3.3.1.8 |
hpnicfLIIPStream OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.111.2 |
hpnicfLIIPStreamObjects OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.111.2.1 |
hpnicfLIIPStreamTableThis table lists the IPv4 and IPv6 streams to be intercepted. It is associated with hpnicfLIMediationTable and hpnicfLIStreamTable. SEQUENCE OF HpnicfLIIPStreamEntry .1.3.6.1.4.1.11.2.14.11.15.2.111.2.1.1 |
hpnicfLIIPStreamEntryA single stream to be intercepted. The first index indicates the Mediation Device. The second index is that of the stream's counter entry in the hpnicfLIStreamTable. The second index permits multiple classifiers to be used together, such as having an IP address as source or destination. HpnicfLIIPStreamEntry .1.3.6.1.4.1.11.2.14.11.15.2.111.2.1.1.1 |
hpnicfLIIPStreamInterfaceTraffic received or transmitted over this interface will be intercepted. This value must be set when creating a stream entry, either zero, or a valid interface index. If the value is zero, interception accepts any interface. Then at least one additional parameter must be selected, and not be default value.rw InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.111.2.1.1.1.1 |
hpnicfLIIPStreamAddrTypeThe type of address, used in packet selection.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.111.2.1.1.1.2 |
hpnicfLIIPStreamDestAddrThe Destination address used in packet selection. This address will be consistent with the type specified in hpnicfLIIPStreamAddrType.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.111.2.1.1.1.3 |
hpnicfLIIPStreamDestAddrLengthThe length of the Destination Prefix. A value of zero means all addresses to match. This prefix length will be consistent with the type specified in hpnicfLIIPStreamAddrType.rw InetAddressPrefixLength (INET-ADDRESS-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.111.2.1.1.1.4 |
hpnicfLIIPStreamSrcAddrThe Source Address used in packet selection. This address will be consistent with the type specified in hpnicfLIIPStreamAddrType.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.111.2.1.1.1.5 |
hpnicfLIIPStreamSrcAddrLengthThe length of the Source Prefix. A value of zero means all addresses to match. This prefix length will be consistent with the type specified in hpnicfLIIPStreamAddrType.rw InetAddressPrefixLength (INET-ADDRESS-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.111.2.1.1.1.6 |
hpnicfLIIPStreamTosByteThe value of the TOS byte. If hpnicfLIIPStreamTosByte&(~hpnicfLIIPStreamTosByteMask)!=0, configuration is rejected.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.111.2.1.1.1.7 |
hpnicfLIIPStreamTosByteMaskThis value is ANDed with the value of the TOS byte in a packet and compared with hpnicfLIIPStreamTosByte. If the values are equal, the comparison is equal. If both the mask and the TosByte value are zero, the result is to always accept.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.111.2.1.1.1.8 |
hpnicfLIIPStreamFlowIdThe flow identifier in an IPv6 header. -1 indicates that the Flow Id is unused.rw Integer32 (-1 | 0..1048575) .1.3.6.1.4.1.11.2.14.11.15.2.111.2.1.1.1.9 |
hpnicfLIIPStreamProtocolThe IP protocol to match against the IPv4 protocol number or the IPv6 Next- Header number in the packet.rw Integer32 (-1 | 0..255) .1.3.6.1.4.1.11.2.14.11.15.2.111.2.1.1.1.10 |
hpnicfLIIPStreamDestL4PortMinThe minimum value that the layer-4 destination port number in the packet must have in order to match. This value must be equal to or less than the value specified for this entry in hpnicfLIIPStreamDestL4PortMax. If both hpnicfLIIPStreamDestL4PortMin and hpnicfLIIPStreamDestL4PortMax are at their default values, the port number is effectively unused. If hpnicfLIIPStreamDestL4PortMin is equal to hpnicfLIIPStreamDestL4PortMax, only one port number to be intercepted.rw InetPortNumber (INET-ADDRESS-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.111.2.1.1.1.11 |
hpnicfLIIPStreamDestL4PortMaxThe maximum value that the layer-4 destination port number in the packet must have in order to match this classifier entry. This value must be equal to or greater than the value specified for this entry in hpnicfLIIPStreamDestL4PortMin. If both hpnicfLIIPStreamDestL4PortMin and hpnicfLIIPStreamDestL4PortMax are at their default values, the port number is effectively unused. If hpnicfLIIPStreamDestL4PortMin is equal to hpnicfLIIPStreamDestL4PortMax, only one port number to be intercepted.rw InetPortNumber (INET-ADDRESS-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.111.2.1.1.1.12 |
hpnicfLIIPStreamSrcL4PortMinThe minimum value that the layer-4 destination port number in the packet must have in order to match. This value must be equal to or less than the value specified for this entry in hpnicfLIIPStreamSrcL4PortMax. If both hpnicfLIIPStreamSrcL4PortMin and hpnicfLIIPStreamSrcL4PortMax are at their default values, the port number is effectively unused. If hpnicfLIIPStreamSrcL4PortMin is equal to hpnicfLIIPStreamSrcL4PortMax, only one port number to be intercepted.rw InetPortNumber (INET-ADDRESS-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.111.2.1.1.1.13 |
hpnicfLIIPStreamSrcL4PortMaxThe maximum value that the layer-4 destination port number in the packet must have in order to match this classifier entry. This value must be equal to or greater than the value specified for this entry in hpnicfLIIPStreamSrcL4PortMin. If both hpnicfLIIPStreamSrcL4PortMin and hpnicfLIIPStreamSrcL4PortMax are at their default values, the port number is effectively unused. If hpnicfLIIPStreamSrcL4PortMin is equal to hpnicfLIIPStreamSrcL4PortMax, only one port number to be intercepted.rw InetPortNumber (INET-ADDRESS-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.111.2.1.1.1.14 |
hpnicfLIIPStreamVRFIt is the name of a Virtual Routing and Forwarding (VRF) of a VPN.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.111.2.1.1.1.15 |
hpnicfLIIPStreamRowStatusOperation status of this table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.111.2.1.1.1.18 |
hpnicfLIMACStream OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.111.3 |
hpnicfLIMACStreamObjects OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.111.3.1 |
hpnicfLIMACStreamTableThis table lists the IEEE 802 streams to be intercepted. It is associated with hpnicfLIMediationTable and hpnicfLIStreamTable. SEQUENCE OF HpnicfLIMACStreamEntry .1.3.6.1.4.1.11.2.14.11.15.2.111.3.1.1 |
hpnicfLIMACStreamEntryA single stream to be intercepted. The first index indicates the Mediation Device. The second index is that of the stream's counter entry in the hpnicfLIStreamTable. The second index permits multiple classifiers to be used together, such as having an MAC address as source or destination. HpnicfLIMACStreamEntry .1.3.6.1.4.1.11.2.14.11.15.2.111.3.1.1.1 |
hpnicfLIMACStreamFieldsThis object displays what attributes will be compared to identify traffic. interface: indicates that traffic on the stated interface is to be intercepted dstMacAddress: indicates that traffic destined to a given address should be intercepted srcMacAddress: indicates that traffic sourced from a given address should be intercepted ethernetPid: indicates that traffic with a stated Ethernet Protocol Identifier should be intercepted dSap: indicates that traffic with an certain 802.2 LLC Destination SAP should be intercepted sSap: indicates that traffic with an certain 802.2 LLC Source SAP should be intercepted At least one of the bits has to be set in order to activate an entry. If multiple bits are set, traffic to be intercepted must be satisfied with all set attributes.rw Bits .1.3.6.1.4.1.11.2.14.11.15.2.111.3.1.1.1.1 |
hpnicfLIMACStreamInterfaceTraffic received or transmitted over this interface will be intercepted. This value must be set when creating a stream entry, either zero, or a valid interface index. If the value is zero, interception accepts any interface. Additional parameter must be selected together.rw InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.111.3.1.1.1.2 |
hpnicfLIMACStreamDestAddrThe Destination address used in packet selection.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.111.3.1.1.1.3 |
hpnicfLIMACStreamSrcAddrThe Source Address used in packet selection.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.111.3.1.1.1.4 |
hpnicfLIMACStreamEthPidThe value of the Ethernet Protocol Identifier in the Ethernet traffic or IEEE 802.2 SNAP traffic.rw Unsigned32 .1.3.6.1.4.1.11.2.14.11.15.2.111.3.1.1.1.5 |
hpnicfLIMACStreamDSapThe value of the IEEE 802.2 Destination SAP.rw Unsigned32 .1.3.6.1.4.1.11.2.14.11.15.2.111.3.1.1.1.6 |
hpnicfLIMACStreamSSapThe value of the IEEE 802.2 Source SAP.rw Unsigned32 .1.3.6.1.4.1.11.2.14.11.15.2.111.3.1.1.1.7 |
hpnicfLIMACStreamRowStatusOperation status of this table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.111.3.1.1.1.8 |
hpnicfLIUserStream OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.111.4 |
hpnicfLIUserStreamObjects OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.111.4.1 |
hpnicfLIUserStreamTableThis table lists the user connection streams to be intercepted. It is associated with hpnicfLIMediationTable and hpnicfLIStreamTable. SEQUENCE OF HpnicfLIUserStreamEntry .1.3.6.1.4.1.11.2.14.11.15.2.111.4.1.1 |
hpnicfLIUserStreamEntryA single stream to be intercepted. The first index indicates the Mediation Device. The second index is that of the stream's counter entry in the hpnicfLIStreamTable. This permits multiple classifiers to be used together. HpnicfLIUserStreamEntry .1.3.6.1.4.1.11.2.14.11.15.2.111.4.1.1.1 |
hpnicfLIUserStreamAcctSessIDThis is the RADIUS attribute 44 acct-session-ID. The string must be set, and the length not be zero.rw OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.111.4.1.1.1.1 |
hpnicfLIUserStreamRowStatusOperation status of this table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.111.4.1.1.1.2 |