Home/Catalog/HPN-ICF-DOT11-RRM-MIB

HPN-ICF-DOT11-RRM-MIB

This MIB file is to provide the object definition of WLAN radio resource management (RRM).
Main OID:
hpnicfDot11RRM.1.3.6.1.4.1.11.2.14.11.15.2.75.8
120
Objects
Active
Status
3
Dependencies

Imported Objects

HPN-ICF-DOT11-REF-MIB
SNMPv2-SMI
SNMPv2-TC

Objects

120 total
Object Name
hpnicfDot11RRMThis MIB file is to provide the object definition of WLAN radio resource management (RRM).
MODULE-IDENTITY
.1.3.6.1.4.1.11.2.14.11.15.2.75.8
hpnicfDot11RRMConfigGroup
OBJECT IDENTIFIER
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1
hpnicfDot11RRMGlobalCfgPara
OBJECT IDENTIFIER
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1
hpnicfDot11RRM11nMadtMaxMcsSpecify the maximum modulation and coding scheme (MCS) index for 802.11n mandatory rates. The value 255 indicates that no maximum MCS index is specified. No maximum MCS index is specified for 802.11n mandatory rates by default. Besides 255, the specified maximum MCS index for 802.11n supported rates must be no less than the specified maximum MCS index for 802.11n mandatory rates.rw
Integer32 (0..76 | 255)
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.1
hpnicfDot11RRM11nSuptMaxMcsSpecify the maximum Modulation and Coding Scheme (MCS) index for 802.11n supported rates. The specified maximum MCS index for 802.11n supported rates must be no less than the specified maximum MCS index for 802.11n mandatory rates.rw
Integer32
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.2
hpnicfDot11RRM11gProtectEnable/Disable dot11g protection.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.3
hpnicfDot11RRM11aPwrConstrtConfigure the power constraint for all 802.11a radios. The configured power constraint is advertised in beacons if spectrum management is enabled. The range of power constraint is 0 to MAX-POWER-1 (where the MAX-POWER is defined by the regulatory domain).rw
Integer32 UNITS "dBm"
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.4
hpnicfDot11RRM11aSpectrumManagEnable/Disable spectrum management for 802.11a radios. When spectrum management is enabled, the WLAN sub-system advertises power capabilities of the AP and power constraints applicable to all devices in the BSS based on regulatory domain specification.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.5
hpnicfDot11RRMAutoChlAvoid11hConfigure the auto-channel set as non-dot11h channels, this is, only the non-dot11h channels belonging to the country code are scanned during initial channel selection and one of them is selected.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.6
hpnicfDot11RRMScanChlSet the scan mode. auto: When this option is set, all channels of the country code being set are scanned. all: When this option is set, all the channels of the radio band are scanned.rw
Enumeration
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.7
hpnicfDot11RRMScanRptIntvelSet the scan report interval.rw
Integer32
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.8
hpnicfDot11APInterfNumThreshhdRepresents threshold of AP interference . If the value of AP interference exceeds this threshold, AP interference trap will be sent. If the value of this node is zero, AP interference trap will be sent immediately.rw
Integer32
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.9
hpnicfDot11StaInterfNumThreshhdRepresents threshold of STA interference. If the value of STA interference exceeds this threshold, STA interference trap will be sent. If the value of this node is zero, STA interference trap will be sent immediately.rw
Integer32
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.10
hpnicfDot11RRM11nMultiCastMcsSpecify the modulation and coding scheme (MCS) index for 802.11n multicast rates. The value 4294967295 indicates that no MCS index is specified. No MCS index is specified for 802.11n multicast rates by default. Besides 4294967295, the specified MCS index for 802.11n multicast rates must be no less than the specified maximum MCS index for 802.11n mandatory rates. Before configure the MCS index for 802.11n multicast rates, the maximum MCS index for 802.11n mandatory rates must be configuredrw
Unsigned32 (0..76 | 4294967295)
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.11
hpnicfDot11RRM11acMadtMaxNssSpecify the maximum NSS index for 802.11ac mandatory rates. The value 0 indicates that no maximum NSS index is specified. No maximum NSS index is specified for 802.11ac mandatory rates by default. The specified maximum NSS index for 802.11ac supported rates must be no less than the specified maximum NSS index for 802.11ac mandatory rates.rw
Integer32
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.12
hpnicfDot11RRM11acSuptMaxNssSpecify the maximum NSS index for 802.11ac supported rates. The specified maximum NSS index for 802.11ac supported rates must be no less than the specified maximum NSS index for 802.11ac mandatory rates.rw
Integer32
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.13
hpnicfDot11RRM11acMultiCastNssSpecify the NSS index for 802.11ac multicast rates. The value 0 indicates that no NSS index is specified. No NSS index is specified for 802.11ac multicast rates by default. The specified NSS index for 802.11ac multicast rates must be no less than the specified maximum NSS index for 802.11ac mandatory rates. Before configuring the NSS index for 802.11ac multicast rates, the maximum NSS index for 802.11ac mandatory rates must be configured. Besides, it must be configured together with the node below.rw
Integer32
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.14
hpnicfDot11RRM11acMultiCastVhtMcsSpecify the MCS index for 802.11ac multicast rates. The value 255 indicates that no MCS index is specified. No MCS index is specified for 802.11ac multicast rates by default. Besides, it must be configured together with the node above.rw
Integer32 (0..9 | 255)
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.15
hpnicfDot11RRMRadioCfgTableConfigure WLAN RRM based radio type. When 802.11b parameter is modified, 802.11g parameter will be changed at the same time. In the same way, when 802.11g parameter is modified, 802.11b parameter will be changed at the same time.
SEQUENCE OF HpnicfDot11RRMRadioCfgEntry
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2
hpnicfDot11RRMRadioCfgEntryConfigure WLAN RRM based radio type. When 802.11b parameter is modified, 802.11g parameter will be changed at the same time. In the same way, when 802.11g parameter is modified, 802.11b parameter will be changed at the same time.
HpnicfDot11RRMRadioCfgEntry
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1
hpnicfDot11RRMRadioType802.11 radio type.
HpnicfDot11RadioType (HPN-ICF-DOT11-REF-MIB)
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.1
hpnicfDot11RRMCfgChlStateEnable/Disable dynamic channel selection.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.2
hpnicfDot11RRMCfgChlModeConfigure the mode of channel selection. This node can be configured only when dynamic channel selection is enabled.rw
Enumeration
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.3
hpnicfDot11RRMChlProntoRadioElmtSpecify the AP and radio that will change channel at next calibration cycle. 0 is returned when getting the value of this node. This node can be configured only when the mode of channel selection control is user-triggered. When configuring, the higher 24 bits stand for the AP index, and the last 8 bits stand for the radio index. 4294967295 stand for configuring each radio on all APs.rw
Unsigned32
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.4
hpnicfDot11RRMCfgPwrStateEnable/Disable dynamic power selection for the band.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.5
hpnicfDot11RRMCfgPwrModeConfigure the mode of transmit power control. This node can be configured only when dynamic power selection is enabled.rw
Enumeration
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.6
hpnicfDot11RRMPwrProntoRadioElmtSpecify the AP and radio that will change power at next calibration cycle. 0 is returned when getting the value of this node. This node can be configured only when the mode of transmit power control is user-triggered. When configuring, the higher 24 bits stand for the AP index, and the last 8 bits stand for the radio index. 4294967295 stand for configuring each radio on all APs.rw
Unsigned32
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.7
hpnicfDot11RRMCfgIntrvlConfigure the calibration interval.rw
Integer32 UNITS "minute"
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.8
hpnicfDot11RRMCfgIntrfThresConfigure the interface threshold. By default, interference observed on an operating channel is considered during dynamic frequency selection and transmit power control. If the interference percentage on the channel reaches the set threshold, RRM will perform resource adjustment to control the situation.rw
Integer32
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.9
hpnicfDot11RRMCfgNoiseThresConfigure the noise threshold.rw
Integer32 (-127..127)
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.10
hpnicfDot11RRMCfgPERThresConfigure the CRC error threshold. If the percentage of CRC errors reaches the threshold, RRM will perform resource adjustment to control the situation.rw
Integer32
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.11
hpnicfDot11RRMCfgToleranceFctrConfigure the tolerance level. During dynamic frequency selection (DFS), the channel will be changed only if there is a better channel having lesser interference and packet error rate than those specified by the user.rw
Integer32
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.12
hpnicfDot11RRMCfgAdjacencyFctrConfigure the adjacency factor for the band. If transmit power control (TPC) is configured, power will be adjusted when the nth neighbor is detected. The value n is the adjacency factor.rw
Integer32
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.13
hpnicfDot11RRMAPCfgTableThis table defines the RRM parameters for AP.
SEQUENCE OF HpnicfDot11RRMAPCfgEntry
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.3
hpnicfDot11RRMAPCfgEntryEach entry contains information of RRM parameters for AP.
HpnicfDot11RRMAPCfgEntry
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.3.1
hpnicfDot11RRMAPWorkModeAP work mode.rw
Enumeration
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.3.1.1
hpnicfDot11RRMSDRadioGroupTableThis table defines RRM self-decisive radio group.
SEQUENCE OF HpnicfDot11RRMSDRadioGroupEntry
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.4
hpnicfDot11RRMSDRadioGroupEntryEach entry contains information of one RRM self-decisive radio group.
HpnicfDot11RRMSDRadioGroupEntry
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.4.1
hpnicfDot11RRMSDRadioGroupIdRepresents RRM self-decisive radio group ID.
Unsigned32
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.4.1.1
hpnicfDot11RRMSDRadioGroupDescRepresents the description of RRM self-decisive radio group.rw
OCTET STRING
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.4.1.2
hpnicfDot11RRMSDRdGrpChlHolddownTmRepresents the channel holddown time of RRM self-decisive radio group.rw
Unsigned32 UNITS "minute"
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.4.1.3
hpnicfDot11RRMSDRdGrpPwrHolddownTmRepresents the power holddown time of RRM self-decisive radio group.rw
Unsigned32 UNITS "minute"
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.4.1.4
hpnicfDot11RRMSDRdGroupRowStatusThe row status of this table entry.rw
RowStatus (SNMPv2-TC)
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.4.1.5
hpnicfDot11RRMAPCfg2TableThis table defines the RRM parameters for AP.
SEQUENCE OF HpnicfDot11RRMAPCfg2Entry
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.5
hpnicfDot11RRMAPCfg2EntryEach entry contains information of RRM parameters for AP.
HpnicfDot11RRMAPCfg2Entry
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.5.1
hpnicfDot11RRMAPSerialIDSerial ID of the AP.
HpnicfDot11ObjectIDType (HPN-ICF-DOT11-REF-MIB)
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.5.1.1
hpnicfDot11RRMAPIntfThresholdRepresents threshold of AP interference . If the number of AP interference exceeds this threshold, AP interference trap will be sent.rw
Integer32
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.5.1.2
hpnicfDot11RRMStaIntfThresholdRepresents threshold of STA interference. If the number of STA interference exceeds this threshold, station interference trap will be sent.rw
Integer32
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.5.1.3
hpnicfDot11RRMCoChlIntfTrapThhdRepresents threshold of interference trap with current ap. If signal strength of the device exceeds this threshold, corresponding trap will be sent.rw
Integer32 UNITS "dbm"
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.5.1.4
hpnicfDot11RRMAdjChlIntfTrapThhdRepresents threshold of adjacent interference trap with current ap. If signal strength of the device exceeds this threshold, corresponding trap will be sent.rw
Integer32 UNITS "dbm"
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.5.1.5
hpnicfDot11RRMDetectGroup
OBJECT IDENTIFIER
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.2
hpnicfDot11RRMChlRptTableThis table shows the RRM channel information of each radio on all APs.
SEQUENCE OF HpnicfDot11RRMChlRptEntry
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1
hpnicfDot11RRMChlRptEntryEach entry contains information of RRM channel information of the radio on the AP.
HpnicfDot11RRMChlRptEntry
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1
hpnicfDot11RRMRadioIndexRepresents index of the radio.ro
HpnicfDot11RadioElementIndex (HPN-ICF-DOT11-REF-MIB)
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.1
hpnicfDot11RRMChlRptChlNumChannel number.ro
Integer32
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.2
hpnicfDot11RRMChlRptChlTypeChannel type.ro
Enumeration
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.3
hpnicfDot11RRMChlRptChlQltyChannel quality.ro
Enumeration
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.4
hpnicfDot11RRMChlRptNbrCntNumber of neighbors found on the channel.ro
Integer32
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.5
hpnicfDot11RRMChlRptLoadLoad observed on the channel in percentage.ro
Integer32
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.6
hpnicfDot11RRMChlRptUtlzUtilization of the channel in percentage.ro
Integer32
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.7
hpnicfDot11RRMChlRptIntrfInterference observed on the channel in percentage.ro
Integer32
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.8
hpnicfDot11RRMChlRptPERPacket error rate observed on the channel in percentage.ro
Integer32
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.9
hpnicfDot11RRMChlRptRetryRatePercentage of retransmission happened on the channel.ro
Integer32
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.10
hpnicfDot11RRMChlRptNoiseNoise observed on the channel.ro
Integer32
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.11
hpnicfDot11RRMChlRptRadarIndtcrRadar detection status.rw
Enumeration
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.12
hpnicfDot11RRMNbrInfoTableThis table shows the RRM neighbor information of each radio on all APs.
SEQUENCE OF HpnicfDot11RRMNbrInfoEntry
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.2
hpnicfDot11RRMNbrInfoEntryEach entry contains information of RRM neighbor information of the radio on an AP.
HpnicfDot11RRMNbrInfoEntry
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.2.1
hpnicfDot11RrmNbrBSSIDMAC address of the AP.
MacAddress (SNMPv2-TC)
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.2.1.1
hpnicfDot11RrmNbrChlChannel number on which the neighbor was found.ro
HpnicfDot11ChannelScopeType (HPN-ICF-DOT11-REF-MIB)
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.2.1.2
hpnicfDot11RRMNbrIntrfInterference observed on the channel in percentage by neighbor.ro
Integer32
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.2.1.3
hpnicfDot11RrmNbrRSSISignal strength of the AP in dBm.ro
Integer32 UNITS "dBm"
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.2.1.4
hpnicfDot11RrmNbrTypeType of the AP, managed or unmanaged.ro
Enumeration
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.2.1.5
hpnicfDot11RrmNbrSSIDSSID of the Neighbor.ro
HpnicfDot11SSIDStringType (HPN-ICF-DOT11-REF-MIB)
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.2.1.6
hpnicfDot11RRMHistoryTableThis table shows the details of the latest three channel changes and power changes applied on all APs, including time of change, reason of the change and the channel, power, interference parameters.
SEQUENCE OF HpnicfDot11RRMHistoryEntry
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3
hpnicfDot11RRMHistoryEntryEach entry shows the details of channel and power changes.
HpnicfDot11RRMHistoryEntry
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1
hpnicfDot11RRMHistoryIdHistory number of the change.
Integer32
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.1
hpnicfDot11RRMHistoryRecIndctrHistory record type of the change.
Enumeration
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.2
hpnicfDot11RRMHistoryChlChannel on which the radio operates before/after the change of channel or power.ro
HpnicfDot11ChannelScopeType (HPN-ICF-DOT11-REF-MIB)
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.3
hpnicfDot11RRMHistoryPwrPower of the radio before/after the change of channel or power.ro
Integer32 UNITS "dBm"
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.4
hpnicfDot11RRMHistoryLoadLoad observed on the radio in percentage before/after the change of channel or power.ro
Integer32
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.5
hpnicfDot11RRMHistoryUtlzUtilization of the radio in percentage before/after the change of channel or power.ro
Integer32
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.6
hpnicfDot11RRMHistoryIntrfInterference observed on the radio in percentage before/after the change of channel or power.ro
Integer32
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.7
hpnicfDot11RRMHistoryNoiseNoise observed on the radio before/after the change of channel or power.ro
Integer32
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.8
hpnicfDot11RRMHistoryPERPacket error rate observed on the radio in percentage before/after the change of channel or power.ro
Integer32
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.9
hpnicfDot11RRMHistoryRetryRatePercentage of retransmission happened on the radio before/after the change of channel or power.ro
Integer32
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.10
hpnicfDot11RRMHistoryChgReasonReason for the change of channel or power. The various bit positions are: |0 |Others | |1 |Coverage | |2 |Radar | |3 |Retransmission | |4 |Packets discarded | |5 |Interference | 0 is returned when the history record type is after.ro
Bits
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.11
hpnicfDot11RRMHistoryChgDateTimeThe time when the channel or power change occurred.ro
DateAndTime (SNMPv2-TC)
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.12
hpnicfDot11RRMRadioNbrInfoTableThis table shows the RRM neighbor information of each radio on all APs.
SEQUENCE OF HpnicfDot11RRMRadioNbrInfoEntry
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.4
hpnicfDot11RRMRadioNbrInfoEntryEach entry contains information of RRM neighbor information of the radio on an AP.
HpnicfDot11RRMRadioNbrInfoEntry
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.4.1
hpnicfDot11RRMRadioNbrAPIDAP serial id.
HpnicfDot11ObjectIDType (HPN-ICF-DOT11-REF-MIB)
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.4.1.1
hpnicfDot11RRMRadioNbrRadioIDRadio Id on AP.
HpnicfDot11RadioScopeType (HPN-ICF-DOT11-REF-MIB)
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.4.1.2
hpnicfDot11RRMRadioNbrSSIDAll neighbour SSIDs scanned by the selected radio.ro
OCTET STRING
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.4.1.3
hpnicfDot11RRMNotifyGroup
OBJECT IDENTIFIER
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.3
hpnicfDot11RRMChlQltyNotifications
OBJECT IDENTIFIER
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.1
hpnicfDot11RRMChlQltyNtfPrefix
OBJECT IDENTIFIER
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.1.0
hpnicfDot11RRMIntrfLimitThis notification will be sent when interference on the radio exceeds the limit.
NOTIFICATION-TYPE
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.1.0.1
hpnicfDot11RRMPERLimitThis notification will be sent when packet error rate on the radio exceeds the limit.
NOTIFICATION-TYPE
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.1.0.2
hpnicfDot11RRMNoiseLimitThis notification will be sent when noise on the radio exceeds the limit.
NOTIFICATION-TYPE
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.1.0.3
hpnicfDot11RRMResChgNotifications
OBJECT IDENTIFIER
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.2
hpnicfDot11RRMResChgNtfPrefix
OBJECT IDENTIFIER
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.2.0
hpnicfDot11RRMPowerChangeThis notification will be sent when power changed on the radio automatically.
NOTIFICATION-TYPE
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.2.0.1
hpnicfDot11RRMNotificationsVar
OBJECT IDENTIFIER
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.3
hpnicfDot11NewPowerPower of the radio after the change of power.ro
Integer32
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.3.1
hpnicfDot11OldPowerPower of the radio before the change of power.ro
Integer32
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.3.2
hpnicfDot11MonitorDetectedGroup
OBJECT IDENTIFIER
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.4
hpnicfDot11MonitorDetectedDevTableThis table shows the devices of AP detected
SEQUENCE OF HpnicfDot11MonitorDetectedDevEntry
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1
hpnicfDot11MonitorDetectedDevEntryEach entry contains information of detected devices.
HpnicfDot11MonitorDetectedDevEntry
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1
hpnicfDot11MonitorDevMACRepresents MAC address of the device detected.
MacAddress (SNMPv2-TC)
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.1
hpnicfDot11MonitorDevTypeRepresents type of the device detected.ro
Enumeration
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.2
hpnicfDot11MonitorDevVendorRepresents vendor of the detected device.ro
OCTET STRING
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.3
hpnicfDot11MonitorDevSSIDRepresents the service set identifier for the ESS of the device which type is ap or adhoc.ro
OCTET STRING
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.4
hpnicfDot11MonitorDevBSSIDRepresents the basic service set identifier of the detected device.ro
MacAddress (SNMPv2-TC)
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.5
hpnicfDot11MonitorDevChannelRepresents the channel in which the device was last detected. AP will choose the channel which has maximum signal strength as effective channel, as there is interference between adjacent channels.ro
HpnicfDot11ChannelScopeType (HPN-ICF-DOT11-REF-MIB)
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.6
hpnicfDot11MonitorRadioIdRepresents the radio ID of the AP that detected the device.ro
HpnicfDot11RadioScopeType (HPN-ICF-DOT11-REF-MIB)
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.7
hpnicfDot11MonitorDevMaxRSSIRepresents the maximum detected RSSI of the device in a scan report cycle.ro
Integer32 UNITS "dbm"
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.8
hpnicfDot11MonitorDevBeaconIntvlRepresents the beacon interval for the detected device(not include the device which type is client).ro
Integer32 UNITS "millisecond"
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.9
hpnicfDot11MonitorDevFstDctTimeRepresents the time at which the device was first detected.ro
DateAndTime (SNMPv2-TC)
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.10
hpnicfDot11MonitorDevLstDctTimeRepresents the time at which the device was detected last time.ro
DateAndTime (SNMPv2-TC)
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.11
hpnicfDot11MonitorDevClearThis object is used to clear the information of the device detected in the WLAN. It will return false for get operation.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.12
hpnicfDot11MonitorDevSNRRepresents the SNR of the device in a scan report cycle.ro
Integer32
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.13
HPN-ICF-DOT11-RRM-MIB - SNMP MIB Reference | MIBs Explorer