HPN-ICF-DOT11-CFG-MIB
This MIB provides information about WLAN configuration.
GLOSSARY
IEEE 802.11 Standard to encourage interoperability among wireless networking equipment.
Access point (AP) Transmitter/receiver (transceiver) device that commonly connects and transports data between a wireless network and a wired network.
Access control (AC) To control and manage multi-APs, it will bridge wireless and wired network.
Fat AP Applied in the home, SOHO and so on, and it could work independently without help from AC.
Fit AP Applied in the enterprise environment, it will work under the control and management from AC.
Control And Provisioning of Wireless Access Points Protocol The short name of protocol is CAPWAP. AC will control and manage AP by CAPWAP tunnel protocol defined by IETF. Also, a data tunnel will be set up between AC and AP.
BSS IEEE 802.11 Basic Service Set (Radio Cell). The BSS of an AP comprises of the stations directly associating with the AP.
Radio The chip set to receive and send wireless signal.
Association The service used to establish access point or station mapping and enable station invocation of the distribution system services. (Wireless clients attempt to connect to access points.)
Basic Rate A data rate that is mandatory for client devices to support in order for them to achieve successful association.
MSDU MAC Service Data Unit, it is frame format defined by
802.11.
TU It is 1,024 microseconds (ms), which is about 1 millisecond.
AKM The authentication and key management method defined by
802.11i, and which includes 802.1x and pre-shared key.
Main OID:
hpnicfDot11CFG.1.3.6.1.4.1.11.2.14.11.15.2.75.4
342
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
342 total| Object Name |
|---|
hpnicfDot11CFGThis MIB provides information about WLAN configuration.
GLOSSARY
IEEE 802.11
Standard to encourage interoperability among
wireless networking equipment.
Access point (AP)
Transmitter/receiver (transceiver) device
that commonly connects and transports data
between a wireless network and a wired network.
Access control (AC)
To control and manage multi-APs, it will bridge
wireless and wired network.
Fat AP
Applied in the home, SOHO and so on, and it could
work independently without help from AC.
Fit AP
Applied in the enterprise environment, it will work
under the control and management from AC.
Control And Provisioning of Wireless Access Points Protocol
The short name of protocol is CAPWAP. AC will control
and manage AP by CAPWAP tunnel protocol defined by IETF.
Also, a data tunnel will be set up between AC and AP.
BSS
IEEE 802.11 Basic Service Set (Radio Cell). The
BSS of an AP comprises of the stations directly
associating with the AP.
Radio
The chip set to receive and send wireless signal.
Association
The service used to establish access point
or station mapping and enable station invocation
of the distribution system services.
(Wireless clients attempt to connect to
access points.)
Basic Rate
A data rate that is mandatory for client
devices to support in order for them to achieve
successful association.
MSDU
MAC Service Data Unit, it is frame format defined by
802.11.
TU
It is 1,024 microseconds (ms), which is about 1
millisecond.
AKM
The authentication and key management method defined by
802.11i, and which includes 802.1x and pre-shared key. MODULE-IDENTITY .1.3.6.1.4.1.11.2.14.11.15.2.75.4 |
hpnicfDot11GlobeConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.75.4.1 |
hpnicfDot11GlobalCountryCodeRepresents the country code for wireless network.rw OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.1 |
hpnicfDot11StaKeepALiveTimerIntvlRepresents the interval of the keep alive requests sent between
AP and STA.
Default value 0 : The keep alive function is disabled.rw Unsigned32 UNITS "second" .1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.2 |
hpnicfDot11StaIdleTimerIntvlRepresents the interval for which the link between AP and STA
( power-save or awake ) can be idle.rw Integer32 UNITS "second" .1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.3 |
hpnicfDot11BroadcastProbeReplyRepresents enable the AP to reply broadcast probe or not.
'true' : The AP to reply broadcast probe is enabled.
'false': The AP to reply broadcast probe is disabledrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.4 |
hpnicfDot11APScanModeRepresents the scanning mode for AP.
The following values are supported:
active - AP will actively do scan.
passive - AP will passively do scan.rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.5 |
hpnicfDot11ACCtrlTunnelSecSupportRepresents what security schemes are supported for CAPWAP Control
tunnel.rw HpnicfDot11TunnelSecSchemType (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.6 |
hpnicfDot11ACDataTunnelSecSupportRepresents what security schemes are supported for CAPWAP data
tunnel. The cleartxt is the default scheme.rw HpnicfDot11TunnelSecSchemType (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.7 |
hpnicfDot11ACAutoAPSupportRepresents enable the auto AP functionality or not.
'true' : The auto AP functionality is enabled.
'false': The auto AP functionality is disabledrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.8 |
hpnicfDot11AutoAPNameRepresents the name of auto AP that needs to be made persistent.
When read the value from the node, NULL value be returned.rw OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.9 |
hpnicfDot11PersistentNameRepresents the new name of auto AP after being made persistent.
When read the value from the node, NULL value be returned.rw OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.10 |
hpnicfDot11IntfTrapThresholdRepresents threshold of interference trap. If signal strength of
the device exceeds this threshold, corresponding trap will
be sent.rw Integer32 UNITS "dbm" .1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.11 |
hpnicfDot11MonitorIntervalRepresents the monitoring interval.
Default value 0 : The monitoring functionality is changed to
real-time mode.rw Unsigned32(0 | 5..15) UNITS "minute" .1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.12 |
hpnicfDot11SampleIntervalRepresents the sampling interval.
Default value 0 : The sampling functionality is disabled.rw Unsigned32(0 | 10..300) UNITS "second" .1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.13 |
hpnicfDot11ChnlSwitChkIntervalRepresents the checking interval of channel switch.rw Unsigned32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.14 |
hpnicfDot11APUserUplimitRepresents the upper limit of user which has access to this AP.rw Unsigned32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.15 |
hpnicfDot11APL2IsolateEnableRepresents enable the layer2 isolation or not.
'true' : The layer2 isolation functionality is enabled.
'false': The layer2 isolation functionality is disabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.16 |
hpnicfDot11APBSSIDSupportNumRepresents the max number of BSSID supported by Current AP.ro Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.17 |
hpnicfDot11APLastUpdateStatTimeRepresents date and time update statistic information lately.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.18 |
hpnicfDot11APDoSProtectEnableRepresents enable the DOS protection or not.
'true' : The DOS protection functionality is enabled.
'false': The DOS protection functionality is disabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.19 |
hpnicfDot11MaxAPPerIfRepresents max AP number that can be connected to AC interface.rw Unsigned32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.20 |
hpnicfDot11SampleTimeStampRepresents the start time of current sample period.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.21 |
hpnicfDot11UplinkTrackIdRepresents the track id of AP.
Default value 0 : The uplink track function for AP is disabled.rw Unsigned32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.22 |
hpnicfDot11RtCollectSwitchThis object is used to turn on/off real-time statistics collection
between AC and AP. If the value is true, hpnicfDot11RtCollectIntvl will
take effect. Otherwise, hpnicfDot11RglCollectIntvl will take effect.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.23 |
hpnicfDot11RglCollectIntvlThis object represents interval to regularly collect statistics from
AC to AP.rw Integer32 UNITS "second" .1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.24 |
hpnicfDot11RtCollectIntvlThis object represents interval to collect real-time statistics from
AC to AP.rw Integer32 UNITS "second" .1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.25 |
hpnicfDot11AllAPCpuUsageThresholdThe CPU usage threshold for all AP.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.26 |
hpnicfDot11AllAPMemUsageThresholdThe memory usage threshold for all AP.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.27 |
hpnicfDot11AdjIntfTrapThresholdRepresents threshold of adjacent interference trap. If signal strength
of the device exceeds this threshold, corresponding trap will be sent.rw Integer32 UNITS "dbm" .1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.28 |
hpnicfDot11AllAPMonitorModeRepresents what work mode for All AP.
The following values are supported:
normal, - AP will supply WLAN service.
monitor - AP will be a monitor to find attack.
hybrid - AP will supply WLAN service and Device detection is
enabled.rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.29 |
hpnicfDot11GlobalApFmwUpdStateRepresents the status of version auto-update for an AP.
The following values are supported:
enable - AP version will be updated automatically.
disable - AP version will not be updated automatically.rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.30 |
hpnicfDot11ACNasIDCMRepresents the NAS-ID of current AC.rw OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.31 |
hpnicfDot11PolicyConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2 |
hpnicfDot11RadioPolicyTableThe table defines the parameters for radio policy, as per
radio policy of CLI.
One radio policy could be assigned to the different radios (AP). SEQUENCE OF HpnicfDot11RadioPolicyEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1 |
hpnicfDot11RadioPolicyEntryEach entry contains information of each radio policy. HpnicfDot11RadioPolicyEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1 |
hpnicfDot11RadioPolicyNameRepresents the name of radio policy. OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.1 |
hpnicfDot11BeaconIntervalRepresents the interval for Beacon management frame.rw Integer32 UNITS "TU" .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.2 |
hpnicfDot11DtimIntervalRepresents the number of beacon intervals that shall elapse
between transmission of Beacons frames containing a Traffic
Indication Map (TIM) element whose DTIM Count field is 0.
This value is transmitted in the Delivery TIM (DTIM) Period
field of Beacon frames.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.3 |
hpnicfDot11RtsThresholdRepresents the current minimum size, in octets, of the MAC
protocol data unit (MPDU), below which a Request to send/Clear
to send (RTS/CTS) handshake shall not be performed.rw Integer32 UNITS "byte" .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.4 |
hpnicfDot11FragThresholdRepresents the current maximum size, in octets, of the MPDU that
may be delivered to the PHY. A MSDU shall be broken into
fragments if its size exceeds the value of this attribute after
adding MAC headers and trailers.rw Integer32 UNITS "byte" .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.5 |
hpnicfDot11ShortRetryThresholdRepresents the maximum number of transmission attempts of a
frame, the length of which is less than or equal to
hpnicfDot11RTSThreshold, which shall be made before a failure
condition is indicated.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.6 |
hpnicfDot11LongRetryThresholdRepresents the maximum number of transmission attempts of a
frame, the length of which is longer than hpnicfDot11RTSThreshold,
that shall be made before a failure condition is indicated.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.7 |
hpnicfDot11MaxRxLifetimeRepresents the elapsed time. After the time specified by
hpnicfDot11MaxRxLifetime, the further attempts to reassemble the
MSDU shall be terminated.rw Unsigned32 UNITS "millisecond" .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.8 |
hpnicfDot11RdoPolicyRowStatusThe status of this table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.9 |
hpnicfDot11RdoClientMaxCountRepresent the maximum number of stations supported by
this radio policy.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.10 |
hpnicfDot11BeaconIntervalMsRepresents the interval for Beacon management frame.rw Integer32 UNITS "ms" .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.11 |
hpnicfDot11ServicePolicyTableThe table defines the parameters for ESS, as per service policy
of CLI.
One service policy could be assigned to the different radios
(AP). SEQUENCE OF HpnicfDot11ServicePolicyEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2 |
hpnicfDot11ServicePolicyEntryEach entry contains information of each service policy. HpnicfDot11ServicePolicyEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1 |
hpnicfDot11ServicePolicyIDRepresents the ID of each service policy. HpnicfDot11ServicePolicyIDType (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.1 |
hpnicfDot11SSIDNameRepresents the ESS. As per CLI, the value of
service policy name will be SSID.rw HpnicfDot11SSIDStringType (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.2 |
hpnicfDot11SSIDHiddenThis attribute controls whether the SSID will be advertised in
the beacon frame.
If it is true, then SSID will not be advertised in the beacon
frame.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.3 |
hpnicfDot11AuthenModeRepresents the Authentication mode defined by 802.11.rw HpnicfDot11AuthenType (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.4 |
hpnicfDot11SSIDEncryptionModeRepresents the encryption mode for this ESS.rw HpnicfDot11SSIDEncryptModeType (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.5 |
hpnicfDot11WlanInfBindingTypeRepresents the service policy will bind to what kind of
data forwarding interface.rw OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.6 |
hpnicfDot11WlanInfBindingIDRepresents the interface ID of the interface that ESS will
bind to.
If the value is set to -1, the binding will be removed.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.7 |
hpnicfDot11SrvPolicyRowStatusThe status of this table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.8 |
hpnicfDot11ClientMaxCountRepresent the maximum number of stations supported by
this service policy.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.9 |
hpnicfDot11SPInCirModeCIR(committed information rate) mode of inbound direction.
This object is useful only when the corresponding CIR is nonzero.
If value of this object is changed, corresponding CIR will be reset.rw HpnicfDot11CirMode (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.10 |
hpnicfDot11SPInCirValueRepresents the CIR of inbound direction of this service policy.
If the value is 0, it means that no flow control is applied to
the service policy, and the corresponding CIR mode is meaningless.rw Integer32 UNITS "Kbps" .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.11 |
hpnicfDot11SPOutCirModeCIR(committed information rate) mode of outbound direction.
This object is useful only when the corresponding CIR is nonzero.
If value of this object is changed, corresponding CIR will be reset.rw HpnicfDot11CirMode (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.12 |
hpnicfDot11SPOutCirValueRepresents the CIR of outbound direction of this service policy.
If the value is 0, it means that no flow control is applied to
the service policy, and the corresponding CIR mode is meaningless.rw Integer32 UNITS "Kbps" .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.13 |
hpnicfDot11WlanInfPVIDRepresents the VLAN ID of SSID.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.14 |
hpnicfDot11SPInCirStaticValueRepresents the CIR of inbound direction for static CIR mode.rw Integer32 UNITS "Kbps" .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.15 |
hpnicfDot11SPOutCirStaticValueRepresents the CIR of outbound direction for static CIR mode.rw Integer32 UNITS "Kbps" .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.16 |
hpnicfDot11SPIsolateIf it is true, then stations connected with the service policy are
isolated.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.17 |
hpnicfDot11WlanexAuthServerIPRepresents the IP address of the Wlanex Authentication serverrw IpAddress .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.18 |
hpnicfDot11SPBeaconMeasEnableIf it is true, then beacon-measurement is enabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.19 |
hpnicfDot11SPBeaconMeasTypeRepresents what the work mode for BeaconMeasurement type.
The following values are supported:
passive, - BeaconMeasurement will use the passive type.
active - BeaconMeasurement will use the active type.
beaconTable - BeaconMeasurement will use the beacon table type.rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.20 |
hpnicfDot11SPBeaconMeasIntervalRepresents the beacon-measurement interval.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.21 |
hpnicfDot11AuthenModeCMRepresents the Authentication mode defined by 802.11.rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.22 |
hpnicfDot11SecIEStatusCMTo enable the security Information element in the beacon and
probe response frames sent by AP.rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.23 |
hpnicfDot11SecurityCiphersCMThe WLAN system support the following cipher type for data frame
encryption.
none
wep40
wep104
tkip
aesccmp
wpi-SMS4
When the value of node equals to zero, it means no configuration or
undo operation.rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.24 |
hpnicfDot11SrvPolicyStatusCMThe status of the Service Policy.rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.25 |
hpnicfDot11SSIDHiddenCMThis attribute controls whether the SSID will be advertised in
beacon frames.
If it is dot11true, the SSID will not be advertised in beacon
frames.rw HpnicfDot11TruthValueCM (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.26 |
hpnicfDot11SPIsolateCMIf it is dot11true, the clients connected with the service policy are
isolated to each other.rw HpnicfDot11TruthValueCM (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.27 |
hpnicfDot11ServicePolicyExtTableThe table defines the parameters for ESS, as per service policy
of CLI.
When the value of hpnicfDot11SSIDEncryptionMode equals to cipher(2),
more configuration for a ESS will be put into the table. SEQUENCE OF HpnicfDot11ServicePolicyExtEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.3 |
hpnicfDot11ServicePolicyExtEntryEach entry contains information of each service policy under cipher(2)
mode. HpnicfDot11ServicePolicyExtEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.3.1 |
hpnicfDot11ServicePolicyExtIDRepresents the ID of each service policy. HpnicfDot11ServicePolicyIDType (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.3.1.1 |
hpnicfDot11SecIEStatusTo enable the security Information element in the beacon and
probe response frames sent by AP.rw HpnicfDot11SecIEStatusType (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.3.1.2 |
hpnicfDot11SecurityCiphersThe WLAN system support the following cipher type for data frame
encryption.
wep40(2)
tkip(4)
aesccmp(16)
wep104(32)
wpisms4(64)
wep128(128)
For each service policy, it could support multiple cipher types at
the same time. So the value of object could combine multiple value
of cipher type above.
When the value of node equals to zero, it means no configuration or
undo operation.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.3.1.3 |
hpnicfDot11CipherKeyIndexRepresents the key index of cipher key for packet.
When hpnicfDot11SecurityCiphers value is wep40 or wep104,
the configuration will take effective.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.3.1.4 |
hpnicfDot11CipherKeyRepresents the cipher key for packet.
When hpnicfDot11SecurityCiphers value is wep40 or wep104,
the configuration will take effective.rw OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.3.1.5 |
hpnicfDot11SrvPolicyExtRowStatusThe status of this table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.3.1.6 |
hpnicfDot11CipherKeyTypeRepresents the cipher key type of hpnicfDot11CipherKey.rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.3.1.7 |
hpnicfDot11RadioPolicyExtTableThe table defines the radio policy of each radio.
It can't be modified if the radio policy is a default radio policy. SEQUENCE OF HpnicfDot11RadioPolicyExtEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4 |
hpnicfDot11RadioPolicyExtEntryEach entry contains information of each radio policy. HpnicfDot11RadioPolicyExtEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1 |
hpnicfDot11RPAPSerialIDThis object represents the Serial ID of AP. OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1.1 |
hpnicfDot11RPRadioIDThis object represents each radio. HpnicfDot11RadioScopeType (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1.2 |
hpnicfDot11RPBeaconIntervalThis object represents the interval for Beacon management frame.rw Integer32 UNITS "milliseconds" .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1.3 |
hpnicfDot11RPDtimIntervalThis object represents the number of beacon intervals that shall elapse
between transmissions of Beacons frames containing a Traffic
Indication Map (TIM) element whose DTIM count field is 0.
This value is transmitted in the Delivery TIM (DTIM) Period
field of Beacon frames.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1.4 |
hpnicfDot11RPRtsThresholdThis object represents the current minimum size, in octets, of the MAC
protocol data unit (MPDU), below which a Request to send/Clear
to send (RTS/CTS) handshake shall not be performed.rw Integer32 UNITS "byte" .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1.5 |
hpnicfDot11RPFragThresholdThis object represents the current maximum size, in octets, of the MPDU
that may be delivered to the PHY. A MSDU shall be broken into
fragments if its size exceeds the value of this attribute after
adding MAC headers and trailers.rw Integer32 UNITS "byte" .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1.6 |
hpnicfDot11RPShortRetryThresholdThis object represents the maximum number of transmission attempts of a
frame, the length of which is less than or equal to
hpnicfDot11RTSThreshold, that shall be made before a failure
condition is indicated.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1.7 |
hpnicfDot11RPLongRetryThresholdThis object represents the maximum number of transmission attempts of a
frame, the length of which is longer than hpnicfDot11RTSThreshold,
and that shall be made before a failure condition is indicated.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1.8 |
hpnicfDot11RPClientMaxCountThis object represents the maximum number of stations supported by
this radio policy.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1.9 |
hpnicfDot11RPBeaconIntervalCMThis object represents beacon interval.rw Integer32 UNITS "timeunit" .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1.10 |
hpnicfDot11SrvPortSecurityTableThis table defines the WLAN security status for ESS, BSS and
WLAN-Ethernet interface which binding the crypto service-template.
Otherwise, when binding the clear service-template,
hpnicfPortSecurityTables should be used to configure port security. SEQUENCE OF HpnicfDot11SrvPortSecurityEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.5 |
hpnicfDot11SrvPortSecurityEntryThere is a row in this table for service policy. HpnicfDot11SrvPortSecurityEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.5.1 |
hpnicfDot11SecurityServicePolicyIDRepresents the ID of each service policy. HpnicfDot11ServicePolicyIDType (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.5.1.1 |
hpnicfDot11SrvPortSecurityModeDetermines the security modes of the WLAN port.
noRestrictions The default value, no any security mode is set.
userLoginSecureExt Access to the port is denied until the port
client is authorized (by 802.1X).
psk Access to the port is denied until the port client is
authorized (by 802.1X key negotiation).
macAddressAndPsk The MAC address is first authenticated and only if
this succeeds does the psk then attempt user authentication.
userLoginSecureExtOrPsk This selects both the userLoginSecureExt and
psk modes together such that either is allowed to authorized access.
Which mode works for client depends on the client's choice.
ext Access to the port is denied until the port client is
authenticated (by ext).rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.5.1.2 |
hpnicfDot11SrvSecurityKeyTypeThis indicates the key type in the 802.1X EAPOL_Key packet.
userLoginTxKeyTypeNone - This means the key type is not set yet.
userLoginTxKeyTypeDot11Key - This selects the 802.11 key type.
userLoginTxKeyTypeRsaRC4Key - This selects the RC4 key for RSA RC4
session encryption.rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.5.1.3 |
hpnicfDot11SrvSecurityPskKeyModeThis is the password input mode. When input as pskKeyModePassPhrase,
hpnicfDot11SrvSecurityPskKeyString must be 8 to 63 characters;
when input as pskKeyModeRawKey, hpnicfDot11SrvSecurityPskKeyString
must be 64 characters and each character must be '0'-'9', 'a'-'f' and
'A'-'F'.rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.5.1.4 |
hpnicfDot11SrvSecurityPskKeyStringThis is the password string used for psk authentication.rw DisplayString .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.5.1.5 |
hpnicfDot11SrvPortSecurityModeCMDetermines the security modes of the WLAN port.
none - The default value, no any security mode is set.
psk - Access to the port is denied until the port client is
authorized (by 802.1X key negotiation).
radius - Access to the port is denied until the port
client is authorized (by 802.1X).
wlanex - Access to the port is denied until the port client is
authenticated by wlan cert.rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.5.1.6 |
hpnicfDot11SrvPolicyExtendTableThe table defines the parameters of each service policy. SEQUENCE OF HpnicfDot11SrvPolicyExtendEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.6 |
hpnicfDot11SrvPolicyExtendEntryEach entry contains information of each service policy. HpnicfDot11SrvPolicyExtendEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.6.1 |
hpnicfDot11SPEnableRepresents whether the service policy is enabled.rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.6.1.1 |
hpnicfDot11APConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3 |
hpnicfDot11APTemplateTableBy AP template CLI, administrator will configure the parameters of AP
by convenience.
Before AP boot up and connect to AC by CAPWAP tunnel, administrator
will create AP template for each AP. When AP connect to AC,
AC will assign configuration to AP by hpnicfDot11APSerialID
information in AP template. SEQUENCE OF HpnicfDot11APTemplateEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1 |
hpnicfDot11APTemplateEntryEach entry contains configuration information for each AP. HpnicfDot11APTemplateEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1 |
hpnicfDot11APTemplateNameRepresents the name of AP template. OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.1 |
hpnicfDot11APSerialIDRepresents AP serial id.rw OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.2 |
hpnicfDot11TemplateAPModelAliasRepresents the alias of AP model name.rw OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.3 |
hpnicfDot11DescriptionThis attribute will give more information about AP.
Administrator could suggest the location, owner or
other information for each AP.
If the value is set to NULL, the description will be removed.rw OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.4 |
hpnicfDot11APWorkModeRepresents what work mode for AP.
The following values are supported:
normal - AP will supply WLAN service.
monitor - AP will be a monitor to find attack.
hybrid - AP will supply WLAN service and Device detection is
enabled.rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.5 |
hpnicfDot11APTemplateRowStatusThe status of this table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.6 |
hpnicfDot11APNameRepresents the AP name.rw OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.7 |
hpnicfDot11StatisIntervRepresents the interval of radio statistic.rw Integer32 UNITS "second" .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.8 |
hpnicfDot11APBroadcastProbeReplyRepresents enable the AP to reply broadcast probe or not.
'true' : The AP to reply broadcast probe is enabled.
'false': The AP to reply broadcast probe is disabledrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.9 |
hpnicfDot11StaIdleTimerIntervRepresents the interval for which the link between AP and STA
( power-save or awake ) can be idle.rw Integer32 UNITS "second" .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.10 |
hpnicfDot11StaKeepAliveTimerIntervRepresents the interval of the keep alive requests sent between
AP and STA.rw Integer32 UNITS "second" .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.11 |
hpnicfDot11APCirRepresents the committed information rate between AP and AC.rw Integer32 UNITS "Kbps" .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.12 |
hpnicfDot11APCbsRepresents the committed burst size between AP and AC.rw Integer32 UNITS "Bytes" .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.13 |
hpnicfDot11APPriorityLevelThis object represents the connection priority for the AP.
If the connection priority is 7, the AC is considered as the
primary AC for the AP.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.14 |
hpnicfDot11APElementIDThis object represents the AP element ID.ro Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.15 |
hpnicfDot11APDevDetectEnableRepresents whether device detection is enabled or not.
'true' : Device detection is enabled.
'false': Device detection is disabled.
If device detection is enabled, the AP will provide both device
detection and WLAN data services.
By default, the AP only provides WLAN data services. When an AP works
in monitor mode, that is, the value of object hpnicfDot11APWorkMode is
monitor, device detection can not be enabled with object
hpnicfDot11APDevDetectEnable.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.16 |
hpnicfDot11APGetIPMethodThis object represents the method how AP gets IP address.rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.17 |
hpnicfDot11StatisIntervModeThis object represents the mode of statics interval.
normal - statics interval value between 10s to 120s
realtime - statics interval value between 2s to 5srw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.18 |
hpnicfDot11ApTrapEnabledRepresents whether the trap status is enabled or not.
'true' : Enable the trap status;
'false' : Disable the trap status.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.19 |
hpnicfDot11ApFmwUpdStateRepresents the status of version auto-update for an AP.
The following values are supported:
enable - AP version will be updated automatically.
disable - AP version will not be updated automatically.
inherit - The status will inherit value from apgroup-view or system-view.rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.20 |
hpnicfDot11StatisIntervModeCMThis object represents the mode of statistic interval.
off - statistic interval value between 10s to 120s
on - statistic interval value between 2s to 5srw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.21 |
hpnicfDot11ApNasIDCMRepresents the NAS-ID of current service policy for each
specific radio of AP.rw OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.22 |
hpnicfDot11RadioToConfigTableBefore AP connects to AC, administrator will configure radio
parameter to each radio. SEQUENCE OF HpnicfDot11RadioToConfigEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2 |
hpnicfDot11RadioToConfigEntryEach entry contains configuration information for each radio. HpnicfDot11RadioToConfigEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1 |
hpnicfDot11APTemplateNameCfgRepresents the name of AP template. OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.1 |
hpnicfDot11CfgRadioIDRepresents each radio. HpnicfDot11RadioScopeType (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.2 |
hpnicfDot11CfgRadioPolicyNameRepresents the name of radio policy.rw OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.3 |
hpnicfDot11CfgRadioTypeRepresents the radio will work with which 802.11 radio type.rw HpnicfDot11RadioType (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.4 |
hpnicfDot11CfgChannelRepresents the channel allocation of radio.rw HpnicfDot11ChannelScopeType (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.5 |
hpnicfDot11CfgMaxTxPowerLevelRepresents the maximal transmit power scope for AP.rw HpnicfDot11TxPwrLevelScopeType UNITS "dbm" .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.6 |
hpnicfDot11PreambleLenRepresents whether use long or short preamble for 802.11 MAC
frame.
When hpnicfDot11CfgRadioType is either dot11b or dot11g,
then value for hpnicfDot11PreambleLen will be valid.
Otherwise, the value for it will be invalid.rw HpnicfDot11PreambleType (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.7 |
hpnicfDot11CfgRadioStatusRepresents the radio admin status whether is enabled
or disabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.8 |
hpnicfDot11CfgRdElementIDRepresents the element ID of this radio. It comprises two parts.
The highest 24 bits are AP element ID and the lowest 8 bits are
radio ID.ro Unsigned32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.9 |
hpnicfDot11CfgWorkModeRepresents work mode of the radio.rw HpnicfDot11WorkMode (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.10 |
hpnicfDot11CfgPwrAttValueRepresents the value of power attenuation.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.11 |
hpnicfDot11RadioTxArithmeticRepresents the transmission arithmetic of the radio.
The following values are supported:
quality - Consider the quality first during the transmission.
bandwidth - Consider the bandwidth first during the transmission.rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.12 |
hpnicfDot11CfgChannelLockStatRepresents locked status of channel on the radio.rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.13 |
hpnicfDot11CfgPowerLockStatRepresents locked status of power on the radio.rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.14 |
hpnicfDot11CfgLBRdGroupIdRepresents the load balance group ID allocated for the radio.rw Unsigned32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.15 |
hpnicfDot11CfgRRMSDRdGroupIdRepresents the RRM self-decisive group ID allocated for the radio.rw Unsigned32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.16 |
hpnicfDot11CfgRadioType2Represents the radio will work with which 802.11 radio type.rw HpnicfDot11RadioType2 (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.17 |
hpnicfDot11CfgIDSEnableRepresents whether intrusion detection is enabled for this radio.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.18 |
hpnicfDot11CfgSaEnableRepresents whether spectrum analysis is enabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.19 |
hpnicfDot11CfgSaCltRtFFTDataRepresents whether to collect real-time FFT data for this radio.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.20 |
hpnicfDot11CfgSaBandRepresents which band of channels will be monitored when collection
real-time FFT data is enabled for this radio. Detection of
interference devices and air quality will also be affected. Each band
responds to the following channels.
dot11g (Channels 1-14)
dot11aLower (channels 36-64)
dot11aMiddle (channels 100-140)
dot11aUpper (channels 149-165).rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.21 |
hpnicfDot11APServiceSetTableFor each radio, it could configure multiple service policies.
The table describes the relationship between radio and
service policies. SEQUENCE OF HpnicfDot11APServiceSetEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.3 |
hpnicfDot11APServiceSetEntryEach entry contains service policy information for each
specific radio of AP. HpnicfDot11APServiceSetEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.3.1 |
hpnicfDot11CfgServicePolicyIDRepresents the ID of each service policy used by the AP. HpnicfDot11ServicePolicyIDType (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.3.1.1 |
hpnicfDot11SrvSetRowStatusThe status of this table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.3.1.2 |
hpnicfDot11ServiceSetVlanIdRepresents the Vlan ID of BSS which is generated when service policy
is binded with the Radio.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.3.1.3 |
hpnicfDot11APSysInfoSetTableThe table of the system information for each AP. SEQUENCE OF HpnicfDot11APSysInfoSetEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.4 |
hpnicfDot11APSysInfoSetEntryThe system information configuration for each AP. HpnicfDot11APSysInfoSetEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.4.1 |
hpnicfDot11APSysNetIDRepresents the system Net ID for AP.rw OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.4.1.1 |
hpnicfDot11APCpuUsageThresholdThe CPU usage threshold for AP.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.4.1.2 |
hpnicfDot11APMemUsageThresholdThe memory usage threshold for AP.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.4.1.3 |
hpnicfDot11APLimitTableFor each connected APs, administrator could configure a series of
limits. This table describes the limit information for AP(s). SEQUENCE OF HpnicfDot11APLimitEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.5 |
hpnicfDot11APLimitEntryEach entry contains the limit information for each AP. HpnicfDot11APLimitEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.5.1 |
hpnicfDot11APSsidNumLimitRepresents the upper limit of service template binded
with this AP. All radios of AP share this limit.
Default value 0 : There is no upper limit of service template
binded with this AP.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.5.1.1 |
hpnicfDot11APUserCntLimitRepresents the upper limit of user which has access to this AP.
All BSSs binded with AP share this limit.
Default value 0 : There is no upper limit of user which has access
to this AP.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.5.1.2 |
hpnicfDot11APUserThresholdRepresents the threshold of user which has access to this
AP. All BSSs binded with AP share this limit. If the user counter
is overflow, the trap will be sent.
Default value 0 : There is no threshold of user which has access
to this AP.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.5.1.3 |
hpnicfDot11APIfSetTableThe table of the interface information for each AP. SEQUENCE OF HpnicfDot11APIfSetEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.6 |
hpnicfDot11APIfSetEntryThe interface information configuration for each AP. HpnicfDot11APIfSetEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.6.1 |
hpnicfDot11APSetIfIndexRepresents the index for a interface. Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.6.1.1 |
hpnicfDot11APIfAliasThis object is an 'alias' name for the interface as specified
by a network manager for AP.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.6.1.2 |
hpnicfDot11APServiceVlanTableFor all the radios on the AP, it could configure multiple service policies.
The table describes the relationship between AP and
service policies. SEQUENCE OF HpnicfDot11APServiceVlanEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.7 |
hpnicfDot11APServiceVlanEntryEach entry contains service policy information for each AP. HpnicfDot11APServiceVlanEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.7.1 |
hpnicfDot11APServiceVlanSerialIDThis object represents AP serial id. OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.7.1.1 |
hpnicfDot11APServiceVlanSPIDThis object represents the ID of each service policy used by the AP. HpnicfDot11ServicePolicyIDType (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.7.1.2 |
hpnicfDot11APServiceVlanIdThis object represents the VLAN ID of BSS which is generated when the
service policy is bound to the radio.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.7.1.3 |
hpnicfDot11APServiceVlanRowStatusThis object represents the status of this table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.7.1.4 |
hpnicfDot11RadioConfigTableBefore AP connects to AC, administrator will configure radio
parameter to each radio. SEQUENCE OF HpnicfDot11RadioConfigEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8 |
hpnicfDot11RadioConfigEntryEach entry contains configuration information for each radio. HpnicfDot11RadioConfigEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1 |
hpnicfDot11RCAPSerialIDThis object represents the Serial ID of AP. OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.1 |
hpnicfDot11RCRadioIDThis object represents each radio. HpnicfDot11RadioScopeType (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.2 |
hpnicfDot11RCRadioTypeThis object represents the radio will work with which 802.11 radio
type.rw HpnicfDot11RadioType (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.3 |
hpnicfDot11RCChannelThis object represents the channel allocation of radio.rw HpnicfDot11ChannelScopeType (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.4 |
hpnicfDot11RCPreambleLenThis object represents whether use long or short preamble for 802.11
MAC frame.
When hpnicfDot11CfgRadioType is either dot11b or dot11g,
then value for hpnicfDot11PreambleLen will be valid.
Otherwise, the value for it will be invalid.rw HpnicfDot11PreambleType (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.5 |
hpnicfDot11RCPwrAttValueThis object represents the value of power attenuation.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.6 |
hpnicfDot11RCApPowerLevelRepresents the maximal transmit power scope for AP.rw HpnicfDot11TxPwrLevelScopeType UNITS "dbm" .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.7 |
hpnicfDot11RCDynamicChlStateEnable/Disable dynamic channel selection.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.8 |
hpnicfDot11RCDynamicPowerStateEnable/Disable dynamic power selection for the band.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.9 |
hpnicfDot11RCRadioStatusRepresents the radio admin status whether is enabled
or disabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.10 |
hpnicfDot11RCRadioRateSet data transmit rates for the radio, in the format of 1,2,5.5...
For 802.11n radios, the format can be MCS X. The data transmit rates
between AP and STA must fall into the configured rates.
(Note: For 802.11n radios, the first value will be treated as a mandatory rate,
and the second value will be treated as a supported rate.
If you configure more than two rates, the configuration cannot take effect.
If you configure only one rate, it is considered as the mandatory rate by default.)rw OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.11 |
hpnicfDot11RCPwrAdjustStepLengthPower adjustment step-length in dBm.ro Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.12 |
hpnicfDot11RCRadioType2This object represents the radio will work with which 802.11 radio
type.rw HpnicfDot11RadioType2 (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.13 |
hpnicfDot11RCPreambleLenCMThis object represents whether use long or short preamble for 802.11
MAC frame.
When hpnicfDot11CfgRadioType is either dot11b or dot11g,
then value for hpnicfDot11PreambleLenCM will be valid.
Otherwise, the value for it will be invalid.rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.14 |
hpnicfDot11RCDynamicChlStateCMEnable/Disable dynamic channel selection.rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.15 |
hpnicfDot11RCRadioStatusCMRepresents the radio admin status whether is enabled
or disabled.rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.16 |
hpnicfDot11RCRadioRateCMSet data transmit rates for the radio, in the format of 1,2,5.5...
For 802.11n radios, the format of each value can be MCS X. The data transmit
rates between AP and client should be one of the configured rates.
(Note: For 802.11n radios, the first value is mandatory rate, and the second
value is supported rate. If more than two rate values are configured, the
configuration will not take effect. If only one rate value is configured,
the mandatory rate will be set to the default value.)rw OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.17 |
hpnicfDot11RCDynamicPowerStateCMEnable/disable dynamic power selection for the band.rw HpnicfDot11TruthValueCM (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.18 |
hpnicfDot11RCRssiThresholdCMRepresents the minimum value of the RSSI.
The clients with RSSI below this value will be refused to associate.rw Integer32 UNITS "dBm" .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.19 |
hpnicfDot11RadioSSIDCfgTableFor each radio, it could configure multiple service policies.
The table describes the relationship between radio and
service policies. SEQUENCE OF HpnicfDot11RadioSSIDCfgEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.9 |
hpnicfDot11RadioSSIDCfgEntryEach entry contains SSID configuration information for each radio. HpnicfDot11RadioSSIDCfgEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.9.1 |
hpnicfDot11RadioSSIDSerialIDThis object represents the serial ID of AP. HpnicfDot11ObjectIDType (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.9.1.1 |
hpnicfDot11RadioSSIDRadioIDThis object represents each radio. HpnicfDot11RadioScopeType (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.9.1.2 |
hpnicfDot11RadioSSIDWLANIDThis object represents the WLAN ID of the BSSID. Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.9.1.3 |
hpnicfDot11RadioSSIDIndexThis object represents the ID of each service policy used by the
radio.rw HpnicfDot11ServicePolicyIDType (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.9.1.4 |
hpnicfDot11RadioBSSIDAs MAC address format, it is used to identify BSS.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.9.1.5 |
hpnicfDot11RadioSSIDRowStatusRowStatus.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.9.1.6 |
hpnicfDot11APSerialIDTableThe table will provide the general information about APs. SEQUENCE OF HpnicfDot11APSerialIDEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10 |
hpnicfDot11APSerialIDEntryEach entry contains the general information of an AP. HpnicfDot11APSerialIDEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1 |
hpnicfDot11SIDAPSerialIDRepresents AP serial id. OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.1 |
hpnicfDot11SIDAPWorkModeRepresents what work mode for AP.
The following values are supported:
normal - AP will supply WLAN service.
monitor - AP will be a monitor to find attack.
hybrid - AP will supply WLAN service and Device detection is
enabled.rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.2 |
hpnicfDot11SIDAPGetIPMethodThis object represents the method how AP gets IP address.rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.3 |
hpnicfDot11SIDAPTemplateNameRepresents the name of AP template.rw OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.4 |
hpnicfDot11SIDModelAliasRepresents the alias of AP model name.rw OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.5 |
hpnicfDot11SIDAPDescriptionThis attribute will give more information about AP.
Administrator could suggest the location, owner or
other information for each AP.
If the value is set to NULL, the description will be removed.rw OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.6 |
hpnicfDot11SIDRowStatusThe status of this table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.7 |
hpnicfDot11SIDAPNameRepresents the AP name.rw OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.8 |
hpnicfDot11SIDStatisIntervRepresents the interval of radio statistic.rw Integer32 UNITS "second" .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.9 |
hpnicfDot11SIDAPBroadcastProbeReplyRepresents enable the AP to reply broadcast probe or not.
'true' : The AP to reply broadcast probe is enabled.
'false': The AP to reply broadcast probe is disabledrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.10 |
hpnicfDot11SIDAPStaIdleTimerIntervRepresents the interval for which the link between AP and STA
( power-save or awake ) can be idle.rw Integer32 UNITS "second" .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.11 |
hpnicfDot11SIDStaKeepAliveTimerIntervRepresents the interval of the keep alive requests sent between
AP and STA.rw Integer32 UNITS "second" .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.12 |
hpnicfDot11SIDAPCirRepresents the committed information rate between AP and AC.rw Integer32 UNITS "Kbps" .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.13 |
hpnicfDot11SIDAPCbsRepresents the committed burst size between AP and AC.rw Integer32 UNITS "Bytes" .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.14 |
hpnicfDot11SIDAPPriorityLevelThis object represents the connection priority for the AP.
If the connection priority is 7, the AC is considered as the
primary AC for the AP.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.15 |
hpnicfDot11SIDAPElementIDThis object represents the AP element ID.ro Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.16 |
hpnicfDot11SIDAPDevDetectEnableRepresents whether device detection is enabled or not.
'true' : Device detection is enabled.
'false': Device detection is disabled.
If device detection is enabled, the AP will provide both device
detection and WLAN data services.
By default, the AP only provides WLAN data services. When an AP works
in monitor mode, that is, the value of object hpnicfDot11APWorkMode is
monitor, device detection can not be enabled with object
hpnicfDot11SIDAPDevDetectEnable.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.17 |
hpnicfDot11SIDAPStatisIntervModeThis object represents the mode of statics interval.
normal - statics interval value between 10s to 120s
realtime - statics interval value between 2s to 5srw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.18 |
hpnicfDot11SIDAPWorkModeCMRepresents what work mode for AP.
The following values are supported:
normal - AP will supply WLAN service.
monitor - AP will be a monitor to find attack.
SemiMonitor - AP will supply WLAN service and Device detection is
enabled.rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.19 |
hpnicfDot11APSTVlanTableFor each service policy, it could be bind to several VLANs.
The table describes the relationship between VLAN and
service policies. SEQUENCE OF HpnicfDot11APSTVlanEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.11 |
hpnicfDot11APSTVlanEntryEach entry contains VLAN and service policy information for each
specific radio of AP. HpnicfDot11APSTVlanEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.11.1 |
hpnicfDot11CfgSTVLANIDRepresents the VLAN that current Service Policy have bind to.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.11.1.1 |
hpnicfDot11CfgSTNASPortIDRepresents the NAS Port ID of current Service Policy for each
specific radio of AP.ro OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.11.1.2 |
hpnicfDot11CfgServiceSetRowStatusThe status of this table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.11.1.3 |
hpnicfDot11CfgSTNASIDRepresents the NAS ID of current Service Policy for each
specific radio of AP.ro OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.11.1.4 |
hpnicfDot11RadioIntfConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.75.4.4 |
hpnicfDot11RadioIntfConfigTableThe table defines the parameters for radio in AP, as per
radio. SEQUENCE OF HpnicfDot11RadioIntfConfigEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1 |
hpnicfDot11RadioIntfConfigEntryEach entry contains information of each radio in AP. HpnicfDot11RadioIntfConfigEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1 |
hpnicfDot11RadioIfIdxRepresents the Radio IfIndex of radio in AP. Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.1 |
hpnicfDot11RadioCfgBeaconIntvlRepresents the interval for Beacon management frame.rw Integer32 UNITS "TU" .1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.2 |
hpnicfDot11RadioCfgDtimIntvlRepresents the number of beacon intervals that shall elapse
between transmission of Beacons frames containing a Traffic
Indication Map (TIM) element whose DTIM Count field is 0.
This value is transmitted in the Delivery TIM (DTIM) Period
field of Beacon frames.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.3 |
hpnicfDot11RadioCfgRtsThresholdRepresents the current minimum size,in octets,of the MAC
protocol data unit (MPDU), below which a Request to send/Clear
to send (RTS/CTS) handshake shall not be performed.rw Integer32 UNITS "Byte" .1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.4 |
hpnicfDot11RadioCfgFragThresholdRepresents the current maximum size, in octets, of the MPDU that
may be delivered to the PHY. A MSDU shall be broken into
fragments if its size exceeds the value of this attribute after
adding MAC headers and trailers.rw Integer32 UNITS "Byte" .1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.5 |
hpnicfDot11RadioCfgShtRetryThldRepresents the maximum number of transmission attempts of a
frame, the length of which is less than or equal to
hpnicfDot11RadioRTSThreshold, that shall be made before a failure
condition is indicated.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.6 |
hpnicfDot11RadioCfglongRtrThldRepresents the maximum number of transmission attempts of a
frame, the length of which is longer than
hpnicfDot11RadioRTSThreshold, that shall be made before a
failure condition is indicated.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.7 |
hpnicfDot11RadioCfgMaxRxLifetimeRepresents the elapsed time. After the time specified by
hpnicfDot11RadioCfgMaxRxLifetime, the further attempts to reassemble
the MSDU shall be terminated.rw Unsigned32 UNITS "millisecond" .1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.8 |
hpnicfDot11RadioCfgTypeRepresents the radio will work with which 802.11 radio type.rw HpnicfDot11RadioType (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.9 |
hpnicfDot11RadioCfgChannelRepresents the channel allocation of radio.rw HpnicfDot11ChannelScopeType (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.10 |
hpnicfDot11RadioCfgMaxTxPwrLvlRepresents the maximal transmit power scope for AP.rw HpnicfDot11TxPwrLevelScopeType UNITS "dbm" .1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.11 |
hpnicfDot11RadioCfgPreambleLenRepresents whether use long or short preamble for 802.11 MAC
frame.rw HpnicfDot11PreambleType (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.12 |
hpnicfDot11RadioCfgWorkModeRepresents work mode of the radio.rw HpnicfDot11WorkMode (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.13 |
hpnicfDot11RadioCfgOnly11gEnableRepresents whether enable only 802.11g radio mode or not.
'true' : Only 802.11g radio mode is enabled.
'false': Only 802.11g radio mode is disabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.14 |
hpnicfDot11RadioCfgType2Represents the radio will work with which 802.11 radio type.rw HpnicfDot11RadioType2 (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.15 |
hpnicfDot11RadioCfgRssithresholdCMRepresents the minimum value of the RSSI.
The clients with RSSI below this value will be refused to associate.rw Integer32 UNITS "dBm" .1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.16 |
hpnicfDot11RadioIntfBindTableThe table defines the binding information for each radio in AP. SEQUENCE OF HpnicfDot11RadioIntfBindEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.2 |
hpnicfDot11RadioIntfBindEntryEach entry contains the radio interface binding information
in AP. HpnicfDot11RadioIntfBindEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.2.1 |
hpnicfDot11RadioIntfBindSvcPlcyIDRepresents the ID of each service policy. HpnicfDot11ServicePolicyIDType (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.2.1.1 |
hpnicfDot11RadioIntfBindIfIdxRepresents the Ifindex of interface which is binded to
the radio.rw Unsigned32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.2.1.2 |
hpnicfDot11RadioIntfBindRowStatusThe status of this table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.2.1.3 |
hpnicfDot11DataRateConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.75.4.5 |
hpnicfDot11DataRateConfigTableTable will provide data rate configuration for a specific radio type. SEQUENCE OF HpnicfDot11DataRateConfigEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.5.1 |
hpnicfDot11DataRateConfigEntryEach entry of the table will provide data rate configuration for a
specific radio type. HpnicfDot11DataRateConfigEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.5.1.1 |
hpnicfDot11RadioTypeIDRepresents the radio type. HpnicfDot11RadioType (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.5.1.1.1 |
hpnicfDot11SupportedRateSetRepresents the supported rate set of a particular radio type.rw OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.75.4.5.1.1.2 |
hpnicfDot11MandatoryRateSetRepresents the mandatory rate set of a particular radio type.rw OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.75.4.5.1.1.3 |
hpnicfDot11DisabledRateSetRepresents the disabled rate set of a particular radio type.rw OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.75.4.5.1.1.4 |
hpnicfDot11SmartRateSetRepresents the rate set of a particular radio type.rw OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.75.4.5.1.1.5 |
hpnicfDot11InterfaceConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.75.4.6 |
hpnicfDot11WlanEssIfTableThis table is used to configure WLAN ESS interface. SEQUENCE OF HpnicfDot11WlanEssIfEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.1 |
hpnicfDot11WlanEssIfEntryEach entry contains the WLAN ESS interface configuration. HpnicfDot11WlanEssIfEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.1.1 |
hpnicfDot11WlanEssIfNumberThis node represents the WLAN ESS interface number. Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.1.1.1 |
hpnicfDot11WlanEssIfIndexThis node represents the ifIndex of WLAN-ESS interface.ro Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.1.1.2 |
hpnicfDot11WlanEssRowStatusThis node represents the WLAN ESS interface row status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.1.1.3 |
hpnicfDot11WlanBssIfTableThis table is used to configure WLAN BSS interface. SEQUENCE OF HpnicfDot11WlanBssIfEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.2 |
hpnicfDot11WlanBssIfEntryEach entry contains the WLAN BSS interface configuration. HpnicfDot11WlanBssIfEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.2.1 |
hpnicfDot11WlanBssIfNumberThis node represents the WLAN BSS interface number. Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.2.1.1 |
hpnicfDot11WlanBssIfIndexThis node represents the ifIndex of WLAN-BSS interface.ro Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.2.1.2 |
hpnicfDot11WlanBssRowStatusThis node represents the WLAN BSS interface row status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.2.1.3 |
hpnicfDot11WLANEthernetIfTableThis table is used to configure WLAN Ethernet interface. SEQUENCE OF HpnicfDot11WLANEthernetIfEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.3 |
hpnicfDot11WLANEthernetIfEntryEach entry contains the WLAN Ethernet interface configuration. HpnicfDot11WLANEthernetIfEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.3.1 |
hpnicfDot11WlanEthernetIfNumberThis node represents the WLAN Ethernet interface number. Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.3.1.1 |
hpnicfDot11WLANEthernetIfIndexThis node represents the ifIndex of WLAN-Ethernet interface.ro Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.3.1.2 |
hpnicfDot11WlanEthernetRowStatusThis node represents the Wlan Ethernet interface row status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.3.1.3 |
hpnicfDot11PortSecurityTableThis table defines the WLAN security status for ESS, BSS, mesh and
WLAN-Ethernet interface which binding the crypto service-template.
Otherwise, when binding the clear service-template,
hpnicfPortSecurityTables should be used to configure port security. SEQUENCE OF HpnicfDot11PortSecurityEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.4 |
hpnicfDot11PortSecurityEntryThere is a row in this table for each ESS, BSS and WLAN-Ethernet
interface.It is indexed using the object ifIndex in RFC1213-MIB. HpnicfDot11PortSecurityEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.4.1 |
hpnicfDot11PortSecurityModeDetermines the security modes of the WLAN port.
noRestrictions - The default value,no any security mode is set.
userLoginSecureExt - Access to the port is denied until the port
client is authorized (by 802.1X).
psk - Access to the port is denied until the port client is
authorized (by 802.1X key negotiation).
macAddressAndPsk - The MAC address is first authenticated and only if
this succeeds does the psk then attempt user authentication.
userLoginSecureExtOrPsk - This selects both the userLoginSecureExt and
psk modes together such that either is allowed to authorized access.
Which mode works for client depends on the client's choice.
ext - Access to the port is denied until the port client is
authenticated (by ext).rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.4.1.1 |
hpnicfDot11SecurityUserLoginTxKeyTypeThis indicates the key type in the 802.1X EAPOL_Key packet.
userLoginTxKeyTypeNone - This means the key type is not set yet.
userLoginTxKeyTypeDot11Key - This selects the 802.11 key type.
userLoginTxKeyTypeRsaRC4Key - This selects the RC4 key for RSA RC4
session encryption.rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.4.1.2 |
hpnicfDot11SecurityPskKeyModeThis is the password input mode. When input as pskKeyModePassPhrase,
hpnicfDot11SecurePskKeyString must be 8 to 63 characters; when input as
pskKeyModeRawKey, hpnicfDot11SecurePskKeyString must be 64 characters and
each character must be '0'-'9', 'a'-'f' and 'A'-'F'.rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.4.1.3 |
hpnicfDot11SecurityPskKeyStringThis is the password string used for psk authentication.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.4.1.4 |
hpnicfDot11WlanMeshIfTableThis table is used to configure WLAN mesh interface. SEQUENCE OF HpnicfDot11WlanMeshIfEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.5 |
hpnicfDot11WlanMeshIfEntryEach entry contains the WLAN mesh interface configuration. HpnicfDot11WlanMeshIfEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.5.1 |
hpnicfDot11WlanMeshIfNumberThis node represents the WLAN mesh interface number. Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.5.1.1 |
hpnicfDot11WlanMeshIfIndexThis node represents the index of WLAN mesh interface.ro Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.5.1.2 |
hpnicfDot11WlanMeshRowStatusThis node represents the WLAN mesh interface row status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.5.1.3 |
hpnicfDot11ACBackupGroup OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.75.4.7 |
hpnicfDot11BackupACAdrssIPThis object represents the backup AC IP address.
If the backup AC IP address is not configured,
the object value is 0.0.0.0.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.7.1 |
hpnicfDot11BackupACAdrssIPv6This object represents the backup AC IPv6 address.
If the backup AC IPv6 address is not configured,
the object value is 0::0.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.7.2 |
hpnicfDot11RadioElementConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.75.4.8 |
hpnicfDot11nRadioCfgTableThis table is used to configure dot11n on the radio. SEQUENCE OF HpnicfDot11nRadioCfgEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.1 |
hpnicfDot11nRadioCfgEntryThis entry contains the dot11n configuration on the radio. HpnicfDot11nRadioCfgEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.1.1 |
hpnicfDot11nRadioCfgIndexRepresents index of the radio. HpnicfDot11RadioElementIndex (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.1.1.1 |
hpnicfDot11nAMpduEnableEnable the function of A-MPDU.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.1.1.2 |
hpnicfDot11nAMsduEnableEnable the function of A-MSDU.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.1.1.3 |
hpnicfDot11nClientDot11nOnlyIf radio type is 802.11an or 802.11gn, only permit clients of 11n mode.
If radio type is 802.11ac, permit clients of 11n and 11ac mode.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.1.1.4 |
hpnicfDot11nChanelBandSpecify the bandwidth mode.rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.1.1.5 |
hpnicfDot11nShortGiEnableThe function of Short GI.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.1.1.6 |
hpnicfDot11nClientDot11acOnlyOnly permit clients of 11ac mode.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.1.1.7 |
hpnicfDot11RadioWDSTableThis table is used to configure WDS on the radio. SEQUENCE OF HpnicfDot11RadioWDSEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.2 |
hpnicfDot11RadioWDSEntryEach entry contains the WDS configuration on the radio. HpnicfDot11RadioWDSEntry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.2.1 |
hpnicfDot11RadioWDSIndexRepresents the element index of radio. HpnicfDot11RadioElementIndex (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.2.1.1 |
hpnicfDot11RadioWDSModeRepresents enable the WDS mode or not.
nowds: The WDS mode is disabled.
wds : The WDS mode is enabledrw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.2.1.2 |
hpnicfDot11RadioWDSNetWorkIDRepresents the mesh ID of WDS.rw OCTET STRING .1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.2.1.3 |
hpnicfDot11WDSSecPskKeyModeRepresents the PSK mode of WDS.rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.2.1.4 |
hpnicfDot11WDSSecPskKeyStringRepresents the PSK value of WDS.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.2.1.5 |
hpnicfDot11nRadioCfg2TableThis table is used to configure dot11n on the radio. SEQUENCE OF HpnicfDot11nRadioCfg2Entry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3 |
hpnicfDot11nRadioCfg2EntryThis entry contains the dot11n configuration on the radio. HpnicfDot11nRadioCfg2Entry .1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1 |
hpnicfDot11nRadioCfg2APIDIndexRepresents index of the AP. HpnicfDot11ObjectIDType (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.1 |
hpnicfDot11nRadioCfg2RadioIDIndexRepresents index of the radio. HpnicfDot11RadioScopeType (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.2 |
hpnicfDot11nRadioCfg2AMpduEnableEnable the function of A-MPDU.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.3 |
hpnicfDot11nRadioCfg2AMsduEnableEnable the function of A-MSDU.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.4 |
hpnicfDot11nRadioCfg2ClientDot11nOnlyIf radio type is 802.11an or 802.11gn, only permit clients of 11n mode.
If radio type is 802.11ac, permit clients of 11n and 11ac mode.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.5 |
hpnicfDot11nRadioCfg2ChannelBandSpecify the bandwidth mode.rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.6 |
hpnicfDot11nRadioCfg2ShortGiEnableEnable the function of Short GI.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.7 |
hpnicfDot11nRadioCfg2AMpduEnableCMEnable the function of A-MPDU.rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.8 |
hpnicfDot11nRadioCfg2ChannelBandCMSpecify the bandwidth mode.rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.9 |
hpnicfDot11nRadioCfg2ShortGiEnableCMEnable the function of Short GI.rw Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.10 |
hpnicfDot11nRadioCfg2ClientDot11acOnlyOnly permit clients of 11ac mode.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.11 |
hpnicfDot11nRadioCfg2ClientDot11nOnlyCMIf radio type is 802.11an or 802.11gn, permit only clients of 11n mode.
If radio type is 802.11ac, permit clients of both 11n and 11ac mode.rw HpnicfDot11TruthValueCM (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.12 |
hpnicfDot11CfgNotifyGroup OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.75.4.9 |
hpnicfDot11CfgNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.0 |
hpnicfDot11CfgCipherChangeThis notification is sent when cipher type of corresponding service
template is changed. NOTIFICATION-TYPE .1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.0.1 |
hpnicfDot11CfgPSKChangeThis notification is sent when pre-shared key of corresponding
service template is changed. NOTIFICATION-TYPE .1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.0.2 |
hpnicfDot11SSIDWepIDConflictTrapThis notification will be sent when the same wep ID is configured
on two service policies. NOTIFICATION-TYPE .1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.0.3 |
hpnicfDot11CfgTrapVarObjects OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.1 |
hpnicfDot11PreConflictTemplateNumRepresents previous service policy ID when radio bind service policy
and current service policy conflict with previous service policy
in cipher configuration.ro Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.1.1 |
hpnicfDot11CurrConflictTemplateNumRepresents current service policy ID when radio bind service policy
and current service policy conflict with previous service policy
in cipher configuration.ro Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.1.2 |
hpnicfDot11ConflictCipherIdxRepresents wep ID that conflicted with.ro Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.1.3 |
hpnicfDot11ConfigureAPIDRepresents which AP is configured.ro HpnicfDot11ObjectIDType (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.1.4 |
hpnicfDot11ConfigureRadioIDRepresents which radio in AP is configured.ro HpnicfDot11RadioScopeType (HPN-ICF-DOT11-REF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.1.5 |
hpnicfDot11ConfigureAPMacAddressRepresents MAC Address of AP.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.1.6 |