HP700RX-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
105
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
105 total| Object Name |
|---|
hp OBJECT IDENTIFIER .1.3.6.1.4.1.11 |
SNMPv2-TC Unknown .1.3.6.1.4.1.11 |
nm OBJECT IDENTIFIER .1.3.6.1.4.1.11.2 |
system OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3 |
netPeripherals OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9 |
hpXStation OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.3 |
config OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.3.1 |
terminal OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.3.1.1 |
monitorThe type of monitor the terminal is configured
to drive. Each monitor type varies in resolution,
refresh rate, color capability, dots per inch,
and synchronization. Some monitors (especially
multi-sync types) may produce usable displays
at several settings.rw Enumeration .1.3.6.1.4.1.11.2.3.9.3.1.1.1 |
monitorDescriptionThe resolution, refresh rate, color capability,
dots per inch, and synchronization the terminal
is sending to its monitor and the part number
of the monitor that works best at these settings.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.3.1.1.2 |
at2kbLEDControlIndicates whether the CAPS-LOCK LED on the
keyboard (if present) is controlled by
the X terminal or the clients (as X LED 3).rw Enumeration .1.3.6.1.4.1.11.2.3.9.3.1.1.3 |
at2kbLanguageThe language setting for an AT/2 keyboard
attached to this terminal.rw Enumeration .1.3.6.1.4.1.11.2.3.9.3.1.1.4 |
serialSpeedThe baud rate of the serial port.rw Enumeration .1.3.6.1.4.1.11.2.3.9.3.1.1.5 |
serialDataBitsThe number of data bits in each character
sent and received over the serial port.rw Enumeration .1.3.6.1.4.1.11.2.3.9.3.1.1.6 |
serialStopBitsThe number of stop bits sent at the end of
each character sent through the serial port.rw Enumeration .1.3.6.1.4.1.11.2.3.9.3.1.1.7 |
serialParityThe parity generated and checked on
each character sent and received through
the serial port.rw Enumeration .1.3.6.1.4.1.11.2.3.9.3.1.1.8 |
serialPacingThe type of flow control used on the serial port.rw Enumeration .1.3.6.1.4.1.11.2.3.9.3.1.1.9 |
serialUseWhat the serial port is being used for. Note
that primary and auxiliary use indicate that
the serial port is 'connected' to TCP ports
9100 and 9101 respectively.rw Enumeration .1.3.6.1.4.1.11.2.3.9.3.1.1.10 |
parallelUseWhat the parallel port is being used for. Note
that primary and auxiliary use indicate that
the serial port is 'connected' to TCP ports
9100 and 9101 respectively.rw Enumeration .1.3.6.1.4.1.11.2.3.9.3.1.1.11 |
portuseEnableThis variable indicates whether remote (through
SNMP) serial port use changes are allowed.rw Enumeration .1.3.6.1.4.1.11.2.3.9.3.1.1.12 |
network OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.3.1.2 |
networkParamsFromIndicates whether the X terminal will use
bootp to get its network parameters (IP address,
default gateway, boot file, terminal name,
domain name, name server addresses, subnet mask,
and remote configuration file) at power up or
use those stored in EEPROM.rw Enumeration .1.3.6.1.4.1.11.2.3.9.3.1.2.1 |
configedAddressThe IP address configured for the Ethernet
interface on this terminal.
The active value for this field is set at
startup. After startup a different value can be
saved to terminal memory without being used,
therefore the value returned via SNMP is not
necessarily the value currently in use.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.3.1.2.2 |
configedSubnetMaskThe subnet mask configured for the Ethernet
interface on this terminal.
The active value for this field is set at
startup. After startup a different value can be
saved to terminal memory without being used,
therefore the value returned via SNMP is not
necessarily the value currently in use.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.3.1.2.3 |
configedRouteTableThe routes configured for this terminal.
At startup the terminal tests the routes
in its routing table. If any route fails,
it will be discarded, therefore the configured
routes may not be the routes in use.
There are a number of ways a route can fail
the startup tests, including: terminal can't ping
the gateway, terminal can't resolve one of the
names into an IP address, or a specified gateway
is not on a connected subnet. SEQUENCE OF RouteTableEntry .1.3.6.1.4.1.11.2.3.9.3.1.2.4 |
routeTableEntryEach entry reflects one route. RouteTableEntry .1.3.6.1.4.1.11.2.3.9.3.1.2.4.1 |
routeIndexThe number of a row in the gateway table on the
Network config screen.ro INTEGER .1.3.6.1.4.1.11.2.3.9.3.1.2.4.1.1 |
routeGatewayThe address of an intermediate machine to
send packets to. Note that this is a string
and may be either a dotted decimal IP address
or a domain name.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.3.1.2.4.1.2 |
routeDestinationThe final destination address for this route.
This may be a machine or a network. Note that this
is a string and may be either a dotted decimal
IP address or a domain name.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.3.1.2.4.1.3 |
primaryFileServerThe address of the first file server the terminal
attempts to contact at startup. This may be
either a node name (in which case it will be
resolved to an address using Domain Name
Resolution) or it may be an IP address in dotted
decimal form.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.3.1.2.5 |
primaryAccessMethodThe method used to read files from the primary
file server. This method may be overridden for
individual paths.rw Enumeration .1.3.6.1.4.1.11.2.3.9.3.1.2.6 |
alternateFileServerThe address of the file server the terminal
will attempt to contact at startup if the primary
file server cannot be reached. This address
may be the node name (in which case it will be
resolved to an address before use using the Domain
Name Resolution) or it may be the address in dotted
decimal form.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.3.1.2.7 |
alternateAccessMethodThe method used to read files from the alternative
file server. This method may be overridden for
individual pathes.rw Enumeration .1.3.6.1.4.1.11.2.3.9.3.1.2.8 |
fileTimeoutThe maximum time (in seconds) that the terminal
will wait for a response to a request to the file
server before giving up. The name resolver timeout
is six times the file timeout.rw INTEGER .1.3.6.1.4.1.11.2.3.9.3.1.2.9 |
primaryNameServerThe primary name server's IP address
in dotted decimal format.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.3.1.2.10 |
alternateNameServerThe alternative name server's IP address
in dotted decimal format. If no answer is received
from the primary name server, the terminal attempts
to contact this name server.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.3.1.2.11 |
domainThe fully qualified domain of the network to
which the terminal is connected. This includes
all parts following the first '.' (dot) in the
fully qualified host name of the terminal.
Typical examples are hp.com or waterloo.edurw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.3.1.2.12 |
terminalNameThe name assigned to this terminal. This
name should correspond to the name assigned
using the Domain Name service, Network Information
Services, and other host address lookup mechanisms.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.3.1.2.13 |
slipLocalAddressThe address used for the terminal end of
the SLIP connection.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.3.1.2.14 |
slipRemoteAddressThe address used for the remote (host) end
end of the SLIP connection.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.3.1.2.15 |
slipMaskThe subnet mask configured for the SLIP
interface on this terminal.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.3.1.2.16 |
startup OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.3.1.3 |
romFontsControls whether or not fonts are read from
the ROM card (if present).rw Enumeration .1.3.6.1.4.1.11.2.3.9.3.1.3.1 |
rgbFileFromControls whether or not the rgb.txt file
is read from the ROM card (if present).rw Enumeration .1.3.6.1.4.1.11.2.3.9.3.1.3.2 |
bootFileFromControls whether or not the X server file
is read from the ROM card (if present).rw Enumeration .1.3.6.1.4.1.11.2.3.9.3.1.3.3 |
bootFileNameThe name of the X server file to load.
This may be a complete path (starting with /)
and may include host and access method overrides.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.3.1.3.4 |
remoteConfigEnabledControls whether or not the remote config
file is read from the file server at startup.rw Enumeration .1.3.6.1.4.1.11.2.3.9.3.1.3.5 |
remoteConfigFileThe name of the remote config file to load at
startup. This may be a complete path (starting
with /) and include host and access method overrides.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.3.1.3.6 |
xdmcpEnabledControls whether or not XDMCP is used to start
user sessions on this terminal.rw Enumeration .1.3.6.1.4.1.11.2.3.9.3.1.3.7 |
xdmcpTypeControls the type of XDMCP request sent
from the terminal at startup.rw Enumeration .1.3.6.1.4.1.11.2.3.9.3.1.3.8 |
xdmcpHostThe address of the host to which the terminal
sends XDMCP requests at startup. This field is
ignored if XDMCP type is BROADCAST.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.3.1.3.9 |
telnetAutoStartDetermines whether a TELNET session is auto-
started at boot time. TELNET can be used
to start a user session, but TELNET cannot be
used if XDMCP is enabled.rw Enumeration .1.3.6.1.4.1.11.2.3.9.3.1.3.10 |
telnetCharSetControls the character set used to display
characters in the TELNET and serial terminal
sessions.rw Enumeration .1.3.6.1.4.1.11.2.3.9.3.1.3.11 |
telnetHostThe address of the host to attempt to connect
to when TELNET is (auto)started. This may be a
name or IP address in dotted decimal format.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.3.1.3.12 |
fontPathTableA list of directory paths used when by the X server
when searching for fonts SEQUENCE OF FontEntry .1.3.6.1.4.1.11.2.3.9.3.1.3.13 |
fontEntryAn single path to a set of font files. FontEntry .1.3.6.1.4.1.11.2.3.9.3.1.3.13.1 |
fontIndexThe index into the list of font paths.ro INTEGER .1.3.6.1.4.1.11.2.3.9.3.1.3.13.1.1 |
fontPathThe actual font path in the format appropriate
to the operating system in use.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.9.3.1.3.13.1.2 |
statistics OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.3.1.4 |
memInstalledThe amount of memory installed in the terminal
(excluding video memory) in Kbytes.ro INTEGER .1.3.6.1.4.1.11.2.3.9.3.1.4.1 |
memFreeThe amount of memory in the free pool (including
free video memory). This is the total amount of
memory that is not currently in use in the terminal.ro INTEGER .1.3.6.1.4.1.11.2.3.9.3.1.4.2 |
memLowMarkThe size of the free pool at its smallest since
the last time this counter was reset.ro INTEGER .1.3.6.1.4.1.11.2.3.9.3.1.4.3 |
memFragsThe number of fragments (of all sizes) in the
memory free pool.ro INTEGER .1.3.6.1.4.1.11.2.3.9.3.1.4.4 |
memLargestFragThe size of the largest fragment in the free pool
in Kbytes. This represents the largest request for
memory that can be fulfilled by the terminal.ro INTEGER .1.3.6.1.4.1.11.2.3.9.3.1.4.5 |
memBackingstoreThe amount of memory used for backingstore in
Kbytes.ro INTEGER .1.3.6.1.4.1.11.2.3.9.3.1.4.6 |
memReclaimsThe number of times memory has been reclaimed
from backing store for other uses.ro Counter .1.3.6.1.4.1.11.2.3.9.3.1.4.7 |
serialInOctetsThe number of octets received through the serial
port since the last time this counter was reset.ro Counter .1.3.6.1.4.1.11.2.3.9.3.1.4.8 |
serialOutOctetsThe number of octets sent out the serial port since
The last time this counter was reset.ro Counter .1.3.6.1.4.1.11.2.3.9.3.1.4.9 |
serialInErrorsThe number of errors detected on data received
in the serial port.ro Counter .1.3.6.1.4.1.11.2.3.9.3.1.4.10 |
parallelOutOctetsThe number of octets sent out the parallel port
since the last time this counter was reset.ro Counter .1.3.6.1.4.1.11.2.3.9.3.1.4.11 |
parallelErrorsThe number of errors detected in sending data
out the parallel port since the last time this
counter was reset.ro Counter .1.3.6.1.4.1.11.2.3.9.3.1.4.12 |
etherInPacketsThe number of packets received over Ethernet.ro Counter .1.3.6.1.4.1.11.2.3.9.3.1.4.13 |
etherInCRCErrorsThe number of CRC errors detected in Ethernet
packets.ro Counter .1.3.6.1.4.1.11.2.3.9.3.1.4.14 |
etherInNoBuffersThe number of time the Ethernet interface hardware
could not receive packets because no buffers were
available.ro Counter .1.3.6.1.4.1.11.2.3.9.3.1.4.15 |
etherInRuntsThe number of packets received on the Ethernet
interface that were shorter then the shortest
permitted packet.ro Counter .1.3.6.1.4.1.11.2.3.9.3.1.4.16 |
etherInOctetsThe number of octets received on the Ethernet
interface.ro Counter .1.3.6.1.4.1.11.2.3.9.3.1.4.17 |
etherOutPacketsThe number of packets sent out the Ethernet
interface.ro Counter .1.3.6.1.4.1.11.2.3.9.3.1.4.18 |
etherOutOneCollisionsThe number of times the Ethernet interface had
to back off once due to a collision.ro Counter .1.3.6.1.4.1.11.2.3.9.3.1.4.19 |
etherOutTwoCollisionsThe number of times the Ethernet interface had
to back off twice due to collisions.ro Counter .1.3.6.1.4.1.11.2.3.9.3.1.4.20 |
etherOutMoreCollisionsThe number of messages for which the Ethernet
interface had to back off more then twice (but less
then the maximum number of times) due to collisions.ro Counter .1.3.6.1.4.1.11.2.3.9.3.1.4.21 |
etherOutMaxCollisionsThe number of times that the Ethernet interface
was unable to transmit a packet due to too many
collisions.ro Counter .1.3.6.1.4.1.11.2.3.9.3.1.4.22 |
etherOutNoBuffersThe number of times that the Ethernet interface
software had to drop an outbound packet because
there were no more interface transmit buffers.ro Counter .1.3.6.1.4.1.11.2.3.9.3.1.4.23 |
etherOutOctetsThe number of octets sent out the Ethernet
interface.ro Counter .1.3.6.1.4.1.11.2.3.9.3.1.4.24 |
tftpTimeoutsThe number of times that the tftp driver has not
gotten a response within the file timeout period.
This is not the number of retransmits performed by
the tftp driver but is the number of completely
failed requests.ro Counter .1.3.6.1.4.1.11.2.3.9.3.1.4.25 |
statsTimeThe statistics information can be cleared (to zero)
by depressing a button on the statistics
screen. This variable indicates the time since this
was last done. It is the amount of time over which
statistics have been collected.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.11.2.3.9.3.1.4.26 |
slipInPacketsThe number of packets received over the serial
interface while running SLIP.ro Counter .1.3.6.1.4.1.11.2.3.9.3.1.4.27 |
slipInOctetsThe number of octets received over the serial
interface while running SLIP.ro Counter .1.3.6.1.4.1.11.2.3.9.3.1.4.28 |
slipInErrsThe number of errors encountered on received octets
on the serial interface while running SLIP.ro Counter .1.3.6.1.4.1.11.2.3.9.3.1.4.29 |
slipOutPacketsThe number of packets transmitted over the serial
interface while running SLIP.ro Counter .1.3.6.1.4.1.11.2.3.9.3.1.4.30 |
slipOutOctetsThe number of octets transmitted over the serial
interface while running SLIP.ro Counter .1.3.6.1.4.1.11.2.3.9.3.1.4.31 |
slipOutErrorsThe number of errors encountered while transmitting
over the serial interface while running SLIP.ro Counter .1.3.6.1.4.1.11.2.3.9.3.1.4.32 |
etherInAlignErrorsThe number of packets received on the Ethernet
interface that were not an integral number of
octets in length.ro Counter .1.3.6.1.4.1.11.2.3.9.3.1.4.33 |
etherInCollisionsThe number of collisions detected on the Ethernet
interface that were after the start of the normal
packet.ro Counter .1.3.6.1.4.1.11.2.3.9.3.1.4.34 |
preferences OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.3.1.5 |
clientAuthenticationControls whether MIT-MAGIC-COOKIE authentication
is used by the server during client connection. If
enabled, the client must pass a valid MAGIC_COOKIE
to the server during the connection sequence. This
feature can only be used with XDMCP enabled.rw Enumeration .1.3.6.1.4.1.11.2.3.9.3.1.5.1 |
accessControlsThis determines whether host access controls are used
by the server during client connection. If enabled, only
those clients running on hosts listed in the terminal's
access control file will be allowed to connect
to the X server. This file is read from the host using
the path
/usr/tftpdir/usr/lib/X11/700X/etc/ipaddress.hosts.rw Enumeration .1.3.6.1.4.1.11.2.3.9.3.1.5.2 |
r3BugCompatabilityThis determines whether the server behaves like an
X11R3 server for certain specific operations.rw Enumeration .1.3.6.1.4.1.11.2.3.9.3.1.5.3 |
reset OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.3.1.6 |
resetEnableThis variable indicates whether remote (through
SNMP) resets are allowed.rw Enumeration .1.3.6.1.4.1.11.2.3.9.3.1.6.1 |
rebootSetting this variable to zero will cause the
X terminal to reset.rw Enumeration .1.3.6.1.4.1.11.2.3.9.3.1.6.2 |
interface OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.4 |
icmp OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.7 |
snmp OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.13 |
trap OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.13.1 |
snmpdConf OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.13.2 |