HP-SN-SWITCH-GROUP-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
315
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
315 total| Object Name |
|---|
snSwInfo OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1 |
SNMPv2-SMI Unknown .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1 |
snSwGroupOperModenoVLan(1) represents all switch ports with no virtual
LAN by port (no Port VLAN), and with no tag assigned.
vlanByPort(2) represents all switch ports with Basic
VLAN (layer2 Switch).rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.1 |
snSwGroupIpL3SwModeThe Switch Group is configured with the Layer3
IP Switch mode either enabled or disabled and the
default is disabled mode.
enabled(1)...........activate Layer3 IP Switch
disabled(0)..........disable Layer3 IP Switchrw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.2 |
snSwGroupIpMcastModeThe Switch Group is configured with the IP Multicast
pruning mode either enabled or disabled and the
default is disabled mode.
enabled(1)...........activate IP Multicast pruning
disabled(0)..........no IP Multicast pruningrw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.3 |
snSwGroupDefaultCfgModeThe Switch Group is configured with the Default
configuration. If the default configuration gets
overwritten, the state will change to non-default.
default(1)...........default configuration
nonDefault(2)..........non default configurationrw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.4 |
snSwGroupSwitchAgeTimeThe Switch Age time is 180sec by default.
The configured range is 10 to 10,000sec. The time
represents the time span to age out an MAC Address
entry.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.5 |
snVLanGroupVlanCurEntryThe current total entry number of VLANs are configured.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.6 |
snVLanGroupSetAllVLanThe value of this object is the VLanIndex of a particalur
entry in snVLanByPortTable (snVLanByPortVLanIndex).
All the attributes of that row of table except PortMask
will be used to set the same attributes for the
entire VLan group. VLanId and PortMask must be set for
that particular entry prior to setting this object.
Switch software will base on that VLAN information
to set the entire VLAN.
Note: All the intended attributes of the given
row of the table (given VLAN) must be set prior
setting this object. When this object is set,
Set-All-VLAN action will take place simultaneously.
The previous setting will be overwritten by the
new one.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.7 |
snSwPortSetAllThe value of this object is the index number of the
snSwPortInfoTable (snSwPortInfoPortIndex).
snSwPortInfoMonitorMode, snSwPortInfoTagMode,
snSwPortInfoChnMode, snSwPortInfoSpeed,
snSwPortInfoAdminStatus are all the
read-write attributes of that row of table.
They will be used to set the same attributes for
all the ports in the system.
Note: prior setting this object, all the intended
attributes of the given row of the table must be set.
Otherwise, the current data of the row will be used to
set the entire port-table. The previous setting will
be overwritten by the new one.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.8 |
snFdbTableCurEntryThe current total entry number of FDB are configured.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.9 |
snFdbTableStationFlushThe following values of the flush state
can only be read:
normal(1)... normal state
error(2)... operation failed
flushing(4)... in process
The following value can be written:
flush(3).....do flush
The agent will return a response even before the flush is done.
And the read value will be flushing until flush is done.
And the flush request will be rejected until error or normal.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.10 |
snPortStpSetAllThe value of this object is 1 which means invoking
Port STP Set-all command. The snPortStpPriority,
snPortStpPathCost, the read-write STP related
attributes of the first row of table will be used
to set the same attributes for all the ports in the
system.
Note: prior setting this object, all the intended
attributes of the given row of the table must be set.
Otherwise, the current data of the row will be used to
set the entire port-table. The previous setting will
be overwritten by the new one.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.11 |
snSwProbePortNumA chassis switch probe port is operated as a traffic analyzer
port and only one port can be assigned in the chassis.
The bit 0 to bit 7: port number.
The bit 8 to bit 11: slot number.
A stackable switch is only assigned with one probe port as a
traffic analyzer.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.12 |
snSw8021qTagModeThe Switch Group is configured with the IEEE802.1q
Tagging mode either enabled or disabled and the
default is disabled mode.
enabled(1)...........activate IEEE802.1q Tagging mode.
disabled(0)..........no IEEE802.1q Tagging.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.13 |
snSwGlobalStpModeSpanning Tree System Global Mode in the Switch Group
can be set either enabled or disabled and the default is
enabled mode.
enabled(1)...........activate Spanning Tree
disabled(0)..........no Spanning Treerw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.14 |
snSwIpMcastQuerierModeThe IP Multicast pruning mode is configured either
Non-Querier or Querier mode and the default is
querier mode.
querier(1)...........when prunning traffic locally
within the VLAN.
nonQuerier(2)........when running with a multicast
capable router in the network.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.15 |
snSwViolatorPortNumberThe port number of the switch or router that received
a violator packet. It is included in the locked
address violation trap.
The bit 0 to bit 7: port number.
The bit 8 to bit 11: slot number (slot for chassis only).ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.17 |
snSwViolatorMacAddressThe source address of the violator packet received
by the switch or router. It is included in the locked
address violation trap.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.18 |
snVLanGroupVlanMaxEntryThe maximum number of VLAN entries are allowed to configure.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.19 |
snSwEosBufferSizeA specific buffer size for all the different EOS buffers.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.20 |
snVLanByPortEntrySizeThe size of each VLAN table entry.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.21 |
snSwPortEntrySizeThe size of each port table entry.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.22 |
snFdbStationEntrySizeThe size of each Fdb station table entry.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.23 |
snPortStpEntrySizeThe size of each port stp table entry.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.24 |
snSwEnableBridgeNewRootTrapIndicates whether the SNMP agent process is
permitted to generate bridge new root traps.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.25 |
snSwEnableBridgeTopoChangeTrapIndicates whether the SNMP agent process is
permitted to generate bridge topology change
traps.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.26 |
snSwEnableLockedAddrViolationTrapIndicates whether the SNMP agent process is
permitted to generate locked address violation
traps.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.27 |
snSwIpxL3SwModeThe Switch Group is configured with the Layer3
IPX Switch mode either enabled or disabled and
the default is disabled mode.
enabled(1)...........activate Layer3 Switch
disabled(0)..........disable Layer3 Switchrw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.28 |
snVLanByIpSubnetMaxSubnetsThe maximum number of subnets for each IP VLAN.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.29 |
snVLanByIpxNetMaxNetworksThe maximum number of networks for each IPX VLAN.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.30 |
snSwProtocolVLanModedisabled(0) - represents system with Protocol VLAN disabled.
enabled(1) - represents system with Protocol VLAN enabled (Layer3 VLAN).rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.31 |
snMacStationVLanIdThis MAC Station VLAN ID index to the standard Forwarding Database for Transparent Bridge Table.
(dot1dTpFdbTable). Since the dot1dTpFdbTable index is the MAC Address assigned to one of
the ports in the bridge(VLAN) and each MAC address can be re-assigned to a different
ports belonging to different bridges(VLANs), the snMacStationVLanId can be used by
users to specify which bridge(VLAN) MAC Station information of the dot1dTpFdbTable
users want to retrieve. If users do not specify the VLan ID in this MIB, the default
VLAN (bridge) ID will be used when dot1dTpFdbTable is retrieved.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.32 |
snSwClearCountersvalid(0) - a SNMP-GET of this mib shows that it is valid command to use.
clear(1) - represents clear counter command of the following counters:
Dot3, MIB2, IP and IPX counters for all ports.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.33 |
snSw8021qTagTypeThe IEEE802.1q tag type embedded in the length/type field of
an Ethernet packet. It specifies that the 2 octets after the
length/type field in an Ethernet packet is the tag value.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.34 |
snSwBroadcastLimitLimit the number of broadcast packets to forward out of the
switch ports. This object specifies the number of broadcast
packets per second. Setting a value of 0 to this object
disables the limitation check.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.35 |
snSwMaxMacFilterPerSystemThe maximum number of MAC Filters per system in the MAC Filter table.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.36 |
snSwMaxMacFilterPerPortThe maximum number of MAC Filters per port in the Port MAC Access Filter table.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.37 |
snSwDefaultVLanIdThe VLAN ID of the DEFAULT PORT-VLAN.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.38 |
snSwGlobalAutoNegotiateThis feature only applies to Gigabit Ethernet ports. If set
to disable(0), all Gigabit Ethernet ports will be put to non-
negotiation mode. If set to enable(1), all Gigabit Ethernet
ports will start auto-negotiation indefinitely until succeed.
If set to negFullAuto(2), all Gigabit Ethernet ports will start
with auto-negotiation, if the negotiation failed, then they
will automatically switch to non-negotiation mode. Stackable
products (except TurboIron 8) Gigabit Ethernet ports do not
support negFullAuto(2). If the snSwPortInfoAutoNegotiate value
of a port was not set to global, this global value does not
apply to the negotiation mode of that port.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.39 |
snSwQosMechanismIndicates whether the qos mechanism is
strict or weighted.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.40 |
snSwSingleStpModeSingle Spanning Tree System Mode in the Switch Group
can be set either enabled or disabled and the default is
disabled mode.
enabled(1)...........activate Single Spanning Tree
disabled(0)..........no Single Spanning Treerw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.41 |
snSwFastStpModeFast Spanning Tree System Mode in the Switch Group
can be set either enabled or disabled and the default is
enabled mode.
enabled(1)...........activate Fast Spanning Tree
disabled(0)..........no Fast Spanning Treerw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.42 |
snVLanInfo OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2 |
snVLanByPortTableIf snSwGroupOperMode is configured as basic mode
which is VLAN by Port, Layer2 switching,
then this table is valid. Each VLAN switch port
could have a number of VLAN IDs.deprecated SEQUENCE OF SnVLanByPortEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1 |
snVLanByPortEntryAn entry in the VLAN By Port Information table.
snVLanByPortVLanIndex = 1 and with
snVLanByPortVLanId = 1 together implies all attributes
applying to the Global switch group i.e. noVLan.
A SNMP SET PDU for a row of the snVLanByPortTable
requires the entired sequence of the MIB Objects in each
snVLanByPortEntry stored in one PDU. Otherwise,
GENERR return-value will be returned.deprecated SnVLanByPortEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1 |
snVLanByPortVLanIndexThe VLAN ID index must not be greater than the
snVLanGroupVlanMaxEntry. Each VLAN Identifier can
have a membership of multiple ports.rodeprecated INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.1 |
snVLanByPortVLanIdThe VLAN ID index to the VLAN By Port Info Table.
Each VLAN Identifier can have a membership of multiple
ports.rwdeprecated INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.2 |
snVLanByPortPortMaskThe Standand-alone switch VLAN port membership. (It was obsoleted for Chassis Product)rwdeprecated PortMask .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.3 |
snVLanByPortQosThe Stand alone stackable switch VLAN Priority values are:
low(0)
high(1)
The BigIron switch VLAN Priority values are:
level0(0), level1(1), level2(2), level3(3),
level4(4), level5(5), level6(6), level7(7)rwdeprecated Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.4 |
snVLanByPortStpModeSpanning Tree Mode in the Switch Group can be set
either enabled or disabled and the default is
enabled mode.
enabled(1)...........activate Spanning Tree
disabled(0)..........no Spanning Treerwdeprecated Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.5 |
snVLanByPortStpPrioritydot1dStpPriority : The value of the write-able
portion of the Stp ID, i.e., the first two octets
of the (8 octet long) Bridge ID. The other (last) 6
octets of the Bridge ID are given by the value of the
base bridge address - dot1dBaseBridgeAddress.rwdeprecated INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.6 |
snVLanByPortStpGroupMaxAgedot1dStpBridgeMaxAge: From RFC1493(Bridge MIB).
The value that all bridges use for MaxAge when
this bridge is acting as the root.
Note that 802.1D-1990 specifies that the
range for this parameter is related to the value of
dot1dStpBridgeHelloTime. The granularity of this
timer is specified by 802.1D-1990 to be 1 second.
An agent may return a badValue error if a set is
attempted to a value which is not a whole number
of seconds.rwdeprecated INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.7 |
snVLanByPortStpGroupHelloTimedot1dStpBridgeHelloTime: From RFC1493(Bridge MIB).
The value that all bridges use for HelloTime when
this bridge is acting as the root. The
granularity of this timer is specified by 802.1D-
1990 to be 1 second. An agent may return a
badValue error if a set is attempted to a value
which is not a whole number of seconds.rwdeprecated INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.8 |
snVLanByPortStpGroupForwardDelaydot1dStpBridgeForwardDelay : From RFC1493(Bridge MIB).
The value that all bridges use for ForwardDelay
when this bridge is acting as the root. Note that
802.1D-1990 specifies that the range for this
parameter is related to the value of
dot1dStpBridgeMaxAge. The granularity of this
timer is specified by 802.1D-1990 to be 1 second.
An agent may return a badValue error if a set is
attempted to a value which is not a whole number
of seconds.rwdeprecated INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.9 |
snVLanByPortRowStatusThis object is used to create and
delete row in the table and control
if they are used. The values
that can be written are:
delete(3)...deletes the row
create(4)...creates a new row
modify(5)...modifies an exsisting row
If the row exists, then a SET with
value of create(4) returns error
'badValue'. Deleted rows go away
immediately. The following values
can be returned on reads:
noSuch(0)...no such row
other(1)....some other case
valid(2)....the row exists and is validrwdeprecated Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.10 |
snVLanByPortOperStateBy default, this mode is set to notActivated(0).
notActivated(0)...the VLAN entry is not activated and not in running mode.
activated(1)......the VLAN entry is activated and in running moderodeprecated Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.11 |
snVLanByPortBaseNumPortsThe number of ports controlled by this bridging
entity.rodeprecated INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.12 |
snVLanByPortBaseTypeIndicates what type of bridging this bridge can
perform. If a bridge is actually performing a
certain type of bridging this will be indicated by
entries in the port table for the given type.rodeprecated Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.13 |
snVLanByPortStpProtocolSpecificationAn indication of what version of the Spanning
Tree Protocol is being run. The value
'decLb100(2)' indicates the DEC LANbridge 100
Spanning Tree protocol. IEEE 802.1d
implementations will return 'ieee8021d(3)'. If
future versions of the IEEE Spanning Tree Protocol
are released that are incompatible with the
current version a new value will be defined.rodeprecated Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.14 |
snVLanByPortStpMaxAgedot1dStpMaxAge: From RFC1493(Bridge MIB).
The maximum age of Spanning Tree Protocol
information learned from the network on any port
before it is discarded, in units of hundredths of
a second. This is the actual value that this
bridge is currently using.rodeprecated Timeout .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.15 |
snVLanByPortStpHelloTimedot1dStpHelloTime: From RFC1493(Bridge MIB).
The amount of time between the transmission of
Configuration bridge PDUs by this node on any port
when it is the root of the spanning tree or trying
to become so, in units of hundredths of a second.
This is the actual value that this bridge is
currently using.rodeprecated Timeout .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.16 |
snVLanByPortStpHoldTimedot1dStpHoldTime: From RFC1493(Bridge MIB).
This time value determines the interval length
during which no more than two Configuration bridge
PDUs shall be transmitted by this node, in units
of hundredths of a second.rodeprecated INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.17 |
snVLanByPortStpForwardDelaydot1dStpForwardDelay: From RFC1493(Bridge MIB).
This time value, measured in units of hundredths
of a second, controls how fast a port changes its
spanning state when moving towards the Forwarding
state. The value determines how long the port
stays in each of the Listening and Learning
states, which precede the Forwarding state. This
value is also used, when a topology change has
been detected and is underway, to age all dynamic
entries in the Forwarding Database. [Note that
this value is the one that this bridge is
currently using, in contrast to
dot1dStpBridgeForwardDelay which is the value that
this bridge and all others would start using
if/when this bridge were to become the root.]rodeprecated Timeout .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.18 |
snVLanByPortStpTimeSinceTopologyChangeThe time (in hundredths of a second) since the
last time a topology change was detected by the
bridge entity.rodeprecated TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.19 |
snVLanByPortStpTopChangesThe total number of topology changes detected by
this bridge since the management entity was last
reset or initialized.rodeprecated Counter .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.20 |
snVLanByPortStpRootCostdot1dStpRootCost: From RFC1493(Bridge MIB).
The cost of the path to the root as seen from
this bridge.rodeprecated INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.21 |
snVLanByPortStpRootPortdot1dStpRootPort: From RFC1493(Bridge MIB).
The port number of the port which offers the
lowest cost path from this bridge to the root
bridge.rodeprecated INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.22 |
snVLanByPortStpDesignatedRootdot1dStpDesignatedRoot: From RFC1493(Bridge MIB).
The bridge identifier of the root of the spanning
tree as determined by the Spanning Tree Protocol
as executed by this node. This value is used as
the Root Identifier parameter in all Configuration
Bridge PDUs originated by this node.rodeprecated BridgeId .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.23 |
snVLanByPortBaseBridgeAddressThe MAC address used by this bridge when it must
be referred to in a unique fashion. It is
recommended that this be the numerically smallest
MAC address of all ports that belong to this
bridge. However it is only required to be unique.
When concatenated with dot1dStpPriority a unique
BridgeIdentifier is formed which is used in the
Spanning Tree Protocol.rodeprecated MacAddress (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.24 |
snVLanByPortVLanNameVLAN Community Name string.rwdeprecated DisplayString .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.25 |
snVLanByPortRouterIntfOptional: A virtual interface for router to the VLAN
If a SNMP-Get value is zero, that means this object was not configured.rwdeprecated INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.26 |
snVLanByPortChassisPortMaskThe Chassis VLAN switch port membership.
(It was obsoleted after release 07100, replaced by snVLanByPortPortList)rwdeprecated OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.27 |
snVLanByPortPortListA list of port indices which are the port
membership of a VLAN By Port. Each port index is a
16-bit integer in big endian order. 8-bit is the slot number,
the other 8-bit is the port number.rwdeprecated OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.28 |
snVLanByProtocolTable. SEQUENCE OF SnVLanByProtocolEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2 |
snVLanByProtocolEntryAn entry in the VLAN By Protocol Configuration table. SnVLanByProtocolEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1 |
snVLanByProtocolVLanIdThe VLAN ID index to both of the VLAN By Port Info Table
and this table.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1.1 |
snVLanByPortMemberTablePort VLAN (Layer 2 VLAN) port membership table. SEQUENCE OF SnVLanByPortMemberEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.6 |
snVLanByPortMemberEntryAn entry of the port VLAN membership table. SnVLanByPortMemberEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.6.1 |
snVLanByPortMemberVLanIdThe VLAN identifier (VLAN ID).ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.6.1.1 |
snVLanByPortMemberPortIdThe ifIndex which is a member of the port VLAN.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.6.1.2 |
snVLanByPortMemberRowStatusThis object is used to create and
delete row in the table and control
if they are used. The values
that can be written are:
delete(3)...deletes the row
create(4)...creates a new row
If the row exists, then a SET with
value of create(4) returns error
'badValue'. Deleted rows go away
immediately. The following values
can be returned on reads:
noSuch(0)...no such row
other(1)....some other case
valid(2)....the row exists and is validrw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.6.1.3 |
snVLanByPortCfgTablePort VLAN (Layer 2 VLAN) configuration table. SEQUENCE OF SnVLanByPortCfgEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7 |
snVLanByPortCfgEntryAn entry of the port VLAN configuration table. SnVLanByPortCfgEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1 |
snVLanByPortCfgVLanIdThe VLAN identifier (VLAN ID).ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.1 |
snVLanByPortCfgQosThe Stand alone stackable switch VLAN Priority values are:
level0(0)
level1(1)
The BigIron switch VLAN Priority values are:
level0(0), level1(1), level2(2), level3(3),
level4(4), level5(5), level6(6), level7(7)rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.2 |
snVLanByPortCfgStpModeSpanning Tree Mode in the Switch Group can be set
either enabled or disabled and the default is
enabled mode.
enabled(1)...........activate Spanning Tree
disabled(0)..........no Spanning Treerw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.3 |
snVLanByPortCfgStpPrioritydot1dStpPriority : The value of the write-able
portion of the Stp ID, i.e., the first two octets
of the (8 octet long) Bridge ID. The other (last) 6
octets of the Bridge ID are given by the value of the
base bridge address - dot1dBaseBridgeAddress.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.4 |
snVLanByPortCfgStpGroupMaxAgedot1dStpBridgeMaxAge: From RFC1493(Bridge MIB).
The value that all bridges use for MaxAge when
this bridge is acting as the root.
Note that 802.1D-1990 specifies that the
range for this parameter is related to the value of
dot1dStpBridgeHelloTime. The granularity of this
timer is specified by 802.1D-1990 to be 1 second.
An agent may return a badValue error if a set is
attempted to a value which is not a whole number
of seconds.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.5 |
snVLanByPortCfgStpGroupHelloTimedot1dStpBridgeHelloTime: From RFC1493(Bridge MIB).
The value that all bridges use for HelloTime when
this bridge is acting as the root. The
granularity of this timer is specified by 802.1D-
1990 to be 1 second. An agent may return a
badValue error if a set is attempted to a value
which is not a whole number of seconds.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.6 |
snVLanByPortCfgStpGroupForwardDelaydot1dStpBridgeForwardDelay : From RFC1493(Bridge MIB).
The value that all bridges use for ForwardDelay
when this bridge is acting as the root. Note that
802.1D-1990 specifies that the range for this
parameter is related to the value of
dot1dStpBridgeMaxAge. The granularity of this
timer is specified by 802.1D-1990 to be 1 second.
An agent may return a badValue error if a set is
attempted to a value which is not a whole number
of seconds.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.7 |
snVLanByPortCfgBaseNumPortsThe number of ports controlled by this bridging
entity.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.8 |
snVLanByPortCfgBaseTypeIndicates what type of bridging this bridge can
perform. If a bridge is actually performing a
certain type of bridging this will be indicated by
entries in the port table for the given type.ro Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.9 |
snVLanByPortCfgStpProtocolSpecificationAn indication of what version of the Spanning
Tree Protocol is being run. The value
'decLb100(2)' indicates the DEC LANbridge 100
Spanning Tree protocol. IEEE 802.1d
implementations will return 'ieee8021d(3)'. If
future versions of the IEEE Spanning Tree Protocol
are released that are incompatible with the
current version a new value will be defined.ro Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.10 |
snVLanByPortCfgStpMaxAgedot1dStpMaxAge: From RFC1493(Bridge MIB).
The maximum age of Spanning Tree Protocol
information learned from the network on any port
before it is discarded, in units of hundredths of
a second. This is the actual value that this
bridge is currently using.ro Timeout .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.11 |
snVLanByPortCfgStpHelloTimedot1dStpHelloTime: From RFC1493(Bridge MIB).
The amount of time between the transmission of
Configuration bridge PDUs by this node on any port
when it is the root of the spanning tree or trying
to become so, in units of hundredths of a second.
This is the actual value that this bridge is
currently using.ro Timeout .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.12 |
snVLanByPortCfgStpHoldTimedot1dStpHoldTime: From RFC1493(Bridge MIB).
This time value determines the interval length
during which no more than two Configuration bridge
PDUs shall be transmitted by this node, in units
of hundredths of a second.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.13 |
snVLanByPortCfgStpForwardDelaydot1dStpForwardDelay: From RFC1493(Bridge MIB).
This time value, measured in units of hundredths
of a second, controls how fast a port changes its
spanning state when moving towards the Forwarding
state. The value determines how long the port
stays in each of the Listening and Learning
states, which precede the Forwarding state. This
value is also used, when a topology change has
been detected and is underway, to age all dynamic
entries in the Forwarding Database. [Note that
this value is the one that this bridge is
currently using, in contrast to
dot1dStpBridgeForwardDelay which is the value that
this bridge and all others would start using
if/when this bridge were to become the root.]ro Timeout .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.14 |
snVLanByPortCfgStpTimeSinceTopologyChangeThe time (in hundredths of a second) since the
last time a topology change was detected by the
bridge entity.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.15 |
snVLanByPortCfgStpTopChangesThe total number of topology changes detected by
this bridge since the management entity was last
reset or initialized.ro Counter .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.16 |
snVLanByPortCfgStpRootCostdot1dStpRootCost: From RFC1493(Bridge MIB).
The cost of the path to the root as seen from
this bridge.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.17 |
snVLanByPortCfgStpRootPortdot1dStpRootPort: From RFC1493(Bridge MIB).
The port number of the port which offers the
lowest cost path from this bridge to the root
bridge.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.18 |
snVLanByPortCfgStpDesignatedRootdot1dStpDesignatedRoot: From RFC1493(Bridge MIB).
The bridge identifier of the root of the spanning
tree as determined by the Spanning Tree Protocol
as executed by this node. This value is used as
the Root Identifier parameter in all Configuration
Bridge PDUs originated by this node.ro BridgeId .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.19 |
snVLanByPortCfgBaseBridgeAddressThe MAC address used by this bridge when it must
be referred to in a unique fashion. It is
recommended that this be the numerically smallest
MAC address of all ports that belong to this
bridge. However it is only required to be unique.
When concatenated with dot1dStpPriority a unique
BridgeIdentifier is formed which is used in the
Spanning Tree Protocol.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.20 |
snVLanByPortCfgVLanNameVLAN Community Name string.rw DisplayString .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.21 |
snVLanByPortCfgRouterIntfOptional: A virtual interface for router to the VLAN
If a SNMP-Get value is zero, that means this object was not configured.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.22 |
snVLanByPortCfgRowStatusUse object to delete a vlan entry.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.23 |
snSwPortInfo OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3 |
snFdbInfo OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.4 |
snPortStpInfo OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.5 |
snPortStpTableA specific snPortStpTable consists of a number of
switch ports. This table only exists if only if
snVLanByPortTable exists and snVLanByPortStpMode is
enabled for each VLAN. SEQUENCE OF SnPortStpEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1 |
snPortStpEntryAn entry in the snPortStpTable indicates the
configuration on a specified port. A SNMP SET PDU
for a row of the snPortStpTable requires the entired
sequence of the MIB Objects in each
snPortStpEntry stored in one PDU. Otherwise,
GENERR return-value will be returned. SnPortStpEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1 |
snPortStpVLanIdThe VLAN ID of the VLAN switch community.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.1 |
snPortStpPortNumThe port number of the Switch.
The bit 0 to bit 7: port number.
The bit 8 to bit 11: slot number (slot for chassis only).ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.2 |
snPortStpPortPriorityThe value of the priority field which is
contained in the first (in network byte order)
octet of the (2 octet long) Port ID. The other
octet of the Port ID is given by the value of
dot1dStpPort.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.3 |
snPortStpPathCostdot1dStpPortPathCost : The contribution of this
port to the path cost of paths towards the spanning
tree root which include this port. 802.1D-1990
recommends that the default value of this parameter
be in inverse proportion to the speed of the
attached LAN. Writing value zero to this object
sets path cost to a default value which automatically
changes according to port speed. Reading value zero
indicates an unknown path cost value because port
speed cannot be determined due to speed auto sense
in progress.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.4 |
snPortStpOperStateBy default, this mode is set to notActivated(0).
notActivated(0)...the Port STP entry is not activated and not in running mode.
activated(1)......the Port STP entry is activated and in running modero Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.5 |
snPortStpPortEnableThe enabled/disabled status of the port. Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.6 |
snPortStpPortForwardTransitionsThe number of times this port has transitioned
from the Learning state to the Forwarding state. Counter .1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.7 |
snPortStpPortStateThe port's current state as defined by
application of the Spanning Tree Protocol. This
state controls what action a port takes on
reception of a frame. If the bridge has detected
a port that is malfunctioning it will place that
port into the broken(6) state. For ports which
are disabled (see dot1dStpPortEnable), this object
will have a value of disabled(1).ro Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.8 |
snPortStpPortDesignatedCostThe path cost of the Designated Port of the
segment connected to this port. This value is
compared to the Root Path Cost field in received
bridge PDUs.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.9 |
snPortStpPortDesignatedRootThe unique Bridge Identifier of the Bridge
recorded as the Root in the Configuration BPDUs
transmitted by the Designated Bridge for the
segment to which the port is attached.ro BridgeId .1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.10 |
snPortStpPortDesignatedBridgeThe Bridge Identifier of the bridge which this
port considers to be the Designated Bridge for
this port's segment.ro BridgeId .1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.11 |
snPortStpPortDesignatedPortThe Port Identifier of the port on the Designated
Bridge for this port's segment.ro OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.12 |
snTrunkInfo OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.6 |
snTrunkTableA specific snTrunkTable consists of a number of
Trunk port-mask. SEQUENCE OF SnTrunkEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.1 |
snTrunkEntryAn entry in the snTrunkTable indicates the
configuration on a specified Trunk port membership. SnTrunkEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.1.1 |
snTrunkIndexThe number of the trunk entries can be configured.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.1.1.1 |
snTrunkPortMaskTrunk membership of the Switch.rw PortMask .1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.1.1.2 |
snTrunkTypeThe trunk connection type which specifies what
device the trunk ports are connected to.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.1.1.3 |
snMSTrunkTableA table contains the configuration of port members of
multi-slot trunk groups. SEQUENCE OF SnMSTrunkEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.2 |
snMSTrunkEntryAn entry of the snMSTrunkTable. SnMSTrunkEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.2.1 |
snMSTrunkPortIndexThe primary port of a trunk group. For module with Gig ports,
primary port is port 1, 3, 5, 7. For module with 10/100 ports,
primary port is port 1, 5, 9, 13, 17, 21.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.2.1.1 |
snMSTrunkPortListA list of port indices which are the port membership
of a trunk group. Each port index is a 16-bit integer
in big endian order. The first port index must be the
primary port index.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.2.1.2 |
snMSTrunkTypeThe trunk connection type which specifies what
device the trunk ports are connected to.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.2.1.3 |
snMSTrunkRowStatusTo create or delete a table entry.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.2.1.4 |
snSwSummary OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.7 |
snSwSummaryModeThe Switch Group Configuration Summary is configured
either enabled or disabled and the
default is disabled mode.
enabled(1)...........activate Switch Configuration Summary.
disabled(0)..........no Switch Configuration Summary.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.7.1 |
snDhcpGatewayListInfo OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.8 |
snDhcpGatewayListTableA table of DHCP gateway list of addresses. SEQUENCE OF SnDhcpGatewayListEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.8.1 |
snDhcpGatewayListEntryAn entry in the IP Port Address table. SnDhcpGatewayListEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.8.1.1 |
snDhcpGatewayListIdThe ID for a DHCP gateway list entry.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.8.1.1.1 |
snDhcpGatewayListAddrListThe DHCP gateway address list for each DHCP gateway list ID.
This list contains 1 to 8 IP addresses represented by octet string.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.1.3.8.1.1.2 |
snDhcpGatewayListRowStatusThis object is used to create and
delete row in the table and control
if they are used. The values
that can be written are:
delete(3)...deletes the row
create(4)...creates a new row or modifies an exsisting row
If the row exists, then a SET with
value of create(4) returns error
'badValue'. Deleted rows go away
immediately. The following values
can be returned on reads:
noSuch(0)...no such row
other(1)....some other case
valid(2)....the row exists and is validrw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.8.1.1.3 |
snDnsInfo OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.9 |
snDnsDomainNameDNS Domain Name string.rw DisplayString .1.3.6.1.4.1.11.2.3.7.11.12.1.3.9.1 |
snDnsGatewayIpAddrListThe DNS Gateway IP address list. This list contains 4
IP addresses represented by octet string.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.1.3.9.2 |
snMacFilter OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.10 |
snMacFilterTableMAC filter table. SEQUENCE OF SnMacFilterEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1 |
snMacFilterEntryAn entry in the MAC filter table. SnMacFilterEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1 |
snMacFilterIndexThe table index for a filter entry.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1.1 |
snMacFilterActionAction to take if the Mac packet match
with this filter.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1.2 |
snMacFilterSourceMacSource MAC address.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1.3 |
snMacFilterSourceMaskSource MAC subnet mask.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1.4 |
snMacFilterDestMacDestination MAC address.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1.5 |
snMacFilterDestMaskDestination MAC subnet mask.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1.6 |
snMacFilterOperatorType of comparison to perform.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1.7 |
snMacFilterFrameTypeFrame Type: ethernet-type, LLC and SNAP typesrw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1.8 |
snMacFilterFrameTypeNumFrame Type Number. 0 means NArw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1.9 |
snMacFilterRowStatusThis object is used to create and
delete row in the table and control
if they are used. The values
that can be written are:
delete(3)...deletes the row
create(4)...creates a new row
modify(5)...modifies an exsisting row
If the row exists, then a SET with
value of create(4) returns error
'badValue'. Deleted rows go away
immediately. The following values
can be returned on reads:
noSuch(0)...no such row
invalid(1)...Setting it to 'invalid' has the effect of
rendering it inoperative..
valid(2)....the row exists and is validrw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1.10 |
snMacFilterPortAccessTableMAC Filter port access table. SEQUENCE OF SnMacFilterPortAccessEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.2 |
snMacFilterPortAccessEntryAn entry in the MAC Filter Port access table. SnMacFilterPortAccessEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.2.1 |
snMacFilterPortAccessPortIndexThe port index.
For FastIron/NetIron products, port index value is from 1 to 42
For BigIron products, port index is an encoded number:
The bit 0 to bit 7: port number.
The bit 8 to bit 11: slot number.
For virtual router interface, slot number is 15,
port number is the virtual router port from 1 to 60.
Therefore, port index value for BigIron is from 257 to 3900.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.2.1.1 |
snMacFilterPortAccessFilters1st octet correspond to 1st filter
number and so on.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.2.1.2 |
snMacFilterPortAccessRowStatusThis object is used to create and
delete row in the table and control
if they are used. The values
that can be written are:
delete(3)...deletes the row
create(4)...creates a new row
If the row exists, then a SET with
value of create(4) returns error
'badValue'. Deleted rows go away
immediately. The following values
can be returned on reads:
noSuch(0)...no such row
invalid(1)...Setting it to 'invalid' has the effect of
rendering it inoperative..
valid(2)....the row exists and is validrw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.2.1.3 |
snNTP OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.11 |
snNTPGeneral OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.1 |
snNTPPollIntervalInterval specifies how often to poll the NTP server.
Each unit is one second.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.1.1 |
snNTPTimeZoneTime zone.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.1.2 |
snNTPSummerTimeEnableEnable/Disable daylight saving time. This enables daylight
saving time for time/date starting 02:00:00 of first Sunday
in April and ending 02:00:00 of last Sunday in October every
year.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.1.3 |
snNTPSystemClockSystem clock, in the following format:
octet 0: seconds after the minute [0-60]
octet 1: minutes after the hour [0-59]
octet 2: hours since midnight [0-23]
octet 3: day of the month [1-31]
octet 4: months since January [0-11]
octet 5: years since 1900
octet 6: days since Sunday [0-6]
Setting this object requires valid value in octets 0 to 5,
and zero in octet 6. System clock can be disabled by setting
zero to all octets.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.1.4 |
snNTPSyncInitiate time synchronization to the NTP servers.
For set operation, only 'synchronize(2)' is accepted.
For get operation, always return 'other(1)'.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.1.5 |
snNTPServerTableNTP (Network Time Protocol) server table. SEQUENCE OF SnNTPServerEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.2 |
snNTPServerEntryAn entry in the NTP server table. SnNTPServerEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.2.1 |
snNTPServerIpNTP server IP address.ro IpAddress .1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.2.1.1 |
snNTPServerVersionNTP server version.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.2.1.2 |
snNTPServerRowStatusTo create or delete a NTP server table entry.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.2.1.3 |
snRadius OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.12 |
snRadiusGeneral OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1 |
snRadiusSNMPAccessIndicate whether Radius group MIB obejcts can be
accessed by SNMP manager. If value is disabled,
all Radius group MIB objects return 'general error'.ro Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1.1 |
snRadiusEnableTelnetAuthEnable/Disable telnet authentication specified
by 'snRadiusLoginMethod'.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1.2 |
snRadiusRetransmitThe number of authentication query retransmissions
to the Radius server.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1.3 |
snRadiusTimeOutInterval specifies how long to wait for authentication
reply from the Radius server, each unit is one second.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1.4 |
snRadiusDeadTimeInterval specifies Radius server dead time,
each unit is one minute.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1.5 |
snRadiusKeyAuthentication key displayed as encrypted text.rw DisplayString .1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1.6 |
snRadiusLoginMethodA sequence of authentication methods. Each octet represents
a method to authenticate the user login process. Each octet
has the following enumeration value:
enable(1) - authenticate by command line interface
enable password
radius(2) - authenticate by requesting radius server
local(3) - authenticate by local user account table
line(4) - authenticate by telnet password
tacplus(5) - authenticate by requesting tacplus server
none(6) - do not authenticate
tacacs(7) - authenticate by requesting tacacs server
Setting a zero length octet string invalidates all
previous authentication methods.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1.7 |
snRadiusEnableMethodA sequence of authentication methods. Each octet represents
a method to authenticate the user entering priviledge mode
of the command line interface. Each octet has the following
enumeration value:
enable(1) - authenticate by command line interface
enable password
radius(2) - authenticate by requesting radius server
local(3) - authenticate by local user account table
line(4) - authenticate by telnet password
tacplus(5) - authenticate by requesting tacplus server
none(6) - do not authenticate
tacacs(7) - authenticate by requesting tacacs server
Setting a zero length octet string invalidates all
previous authentication methods.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1.8 |
snRadiusWebServerMethodA sequence of authentication methods. Each octet represents
a method to authenticate the user accessing the web-server.
Each octet has the following enumeration value:
enable(1) - authenticate by command line interface
enable password
radius(2) - authenticate by requesting radius server
local(3) - authenticate by local user account table
line(4) - authenticate by telnet password
tacplus(5) - authenticate by requesting tacplus server
none(6) - do not authenticate
tacacs(7) - authenticate by requesting tacacs server
Setting a zero length octet string invalidates all
previous authentication methods.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1.9 |
snRadiusSNMPServerMethodA sequence of authentication methods. Each octet represents
a method to authenticate the user accessing the snmp-server.
Each octet has the following enumeration value:
enable(1) - authenticate by command line interface
enable password
radius(2) - authenticate by requesting radius server
local(3) - authenticate by local user account table
line(4) - authenticate by telnet password
tacplus(5) - authenticate by requesting tacplus server
none(6) - do not authenticate
tacacs(7) - authenticate by requesting tacacs server
Setting a zero length octet string invalidates all
previous authentication methods.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1.10 |
snRadiusServerTableRadius server table. SEQUENCE OF SnRadiusServerEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.2 |
snRadiusServerEntryAn entry in the Radius server table. SnRadiusServerEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.2.1 |
snRadiusServerIpRadius server IP address.ro IpAddress .1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.2.1.1 |
snRadiusServerAuthPortAuthentication UDP port number.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.2.1.2 |
snRadiusServerAcctPortAccount UDP port number.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.2.1.3 |
snRadiusServerRowStatusTo create or delete a Radius server table entry.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.2.1.4 |
snRadiusServerRowKeyAuthentication key displayed as encrypted text.rw DisplayString .1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.2.1.5 |
snRadiusServerUsageTo allow this server to be dedicated for a particular AAA activity.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.2.1.6 |
snTacacs OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.13 |
snTacacsGeneral OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.1 |
snTacacsRetransmitThe number of authentication query retransmissions
to the Tacacs server.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.1.1 |
snTacacsTimeOutInterval specifies how long to wait for authentication
reply from the Tacacs server, each unit is one second.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.1.2 |
snTacacsDeadTimeInterval specifies Tacacs server dead time,
each unit is one minute.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.1.3 |
snTacacsKeyAuthentication key displayed as encrypted text.rw DisplayString .1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.1.4 |
snTacacsSNMPAccessIndicate whether Tacacs group MIB obejcts can be
accessed by SNMP manager. If value is disabled,
all Tacacs group MIB objects return 'general error'.ro Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.1.5 |
snTacacsServerTableTacacs server table. SEQUENCE OF SnTacacsServerEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.2 |
snTacacsServerEntryAn entry in the Tacacs server table. SnTacacsServerEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.2.1 |
snTacacsServerIpTacacs server IP address.ro IpAddress .1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.2.1.1 |
snTacacsServerAuthPortAuthentication UDP port number.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.2.1.2 |
snTacacsServerRowStatusTo create or delete a Tacacs server table entry.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.2.1.3 |
snTacacsServerRowKeyAuthentication key displayed as encrypted text.rw DisplayString .1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.2.1.4 |
snTacacsServerUsageTo allow this server to be dedicated for a particular AAA activity.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.2.1.5 |
snQos OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.14 |
snQosProfileTableA table contains the configuration of qos profile
groups. SEQUENCE OF SnQosProfileEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.1 |
snQosProfileEntryAn entry of the snQosProfileTable. SnQosProfileEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.1.1 |
snQosProfileIndexThe table index of QOS Profile.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.1.1.1 |
snQosProfileNameQos Profile Name string.rw DisplayString .1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.1.1.2 |
snQosProfileRequestedBandwidthQos Profile Requested Bandwidth.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.1.1.3 |
snQosProfileCalculatedBandwidthQos Profile Calculated Bandwidth.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.1.1.4 |
snQosBindTableA table contains the configuration of 802.1p to qos profile
binding groups. SEQUENCE OF SnQosBindEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.2 |
snQosBindEntryAn entry of the snQosBindTable. SnQosBindEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.2.1 |
snQosBindIndexThe table index of QOS Bind.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.2.1.1 |
snQosBindPriorityQOS bind priority.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.2.1.2 |
snQosBindProfileIndexQOS Bind Profile Index. This is pointer to the
index of snQosProfile Table.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.2.1.3 |
snAAA OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.15 |
snAuthentication OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.15.1 |
snAuthorization OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.15.2 |
snAuthorizationCommandMethodsA sequence of authorization methods. Each octet represents
a method to authorize the user command. Each octet
has the following value:
radius(2) - authorize by requesting radius server
tacplus(5) - authorize by requesting tacplus server
none(6) - skip authorization
Setting a zero length octet string invalidates all
previous authorization methods.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.1.3.15.2.1 |
snAuthorizationCommandLevelCommands, which are equal to and less than the specified
command level here needs to be authorized. Possible enumeration
values:
0 - Privilege level 0
4 - Privilege level 4
5 - Privilege level 5.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.15.2.2 |
snAuthorizationExecA sequence of exec authorization methods. Each octet represents
a method for telnet or SSH login authorization. Each octet
has the following enumeration value:
radius(2) - send exec authorization request to radius server
tacplus(5) - send exec authorization request to tacplus server
none(6) - no exec authorization
Setting a zero length octet string invalidates all
authorization methods.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.1.3.15.2.3 |
snAccounting OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.15.3 |
snAccountingCommandMethodsA sequence of accounting methods. Each octet represents
a method to account for the user command. Each octet
has the following enumeration value:
radius(2) - send accounting info to radius server
tacplus(5) - send accounting info to tacplus server
none(6) - skip accounting
Setting a zero length octet string invalidates all
previous accounting methods.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.1.3.15.3.1 |
snAccountingCommandLevelCommands, which are equal to and less than the specified
command level here will be accounted. Possible enumeration
values:
level0 - Privilege level 0
level4 - Privilege level 4
level5 - Privilege level 5.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.15.3.2 |
snAccountingExecA sequence of accounting methods. Each octet represents
a method for telnet or SSH login accounting. Each octet
has the following enumeration value:
radius(2) - send accounting info to radius server
tacplus(5) - send accounting info to tacplus server
none(6) - skip accounting
Setting a zero length octet string invalidates all
previous accounting methods.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.1.3.15.3.3 |
snAccountingSystemA sequence of accounting methods. Each octet represents
a method to account for the system related events. Each octet
has the following enumeration value:
radius(2) - send accounting info to radius server
tacplus(5) - send accounting info to tacplus server
none(6) - skip accounting
Setting a zero length octet string invalidates all
previous accounting methods.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.1.3.15.3.4 |
snCAR OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.16 |
snVLanCAR OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.17 |
snNetFlow OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.18 |
snNetFlowGlb OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.1 |
snNetFlowGblEnableEnable/disable NetFlow export operation.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.1.1 |
snNetFlowGblVersionNetFlow export version.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.1.2 |
snNetFlowGblProtocolDisablebit 0 - other, disable all protocols export except UDP and TCP
bit 1 - tcp, disable TCP protocol export
bit 2 - udp, disable UDP protocol exportrw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.1.3 |
snNetFlowGblActiveTimeoutMaximum time an active flow can be in the NetFlow cache (minutes: 1..60)rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.1.4 |
snNetFlowGblInactiveTimeoutMaximum time an inactive flow can be in the NetFlow cache (seconds: 10..600)rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.1.5 |
snNetFlowCollectorTableA table of each NetFlow collector information. SEQUENCE OF SnNetFlowCollectorEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.2 |
snNetFlowCollectorEntryA row in the NetFlow collector table. SnNetFlowCollectorEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.2.1 |
snNetFlowCollectorIndexThe index to the NetFlow collector table.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.2.1.1 |
snNetFlowCollectorIpThe NetFlow collector ip address.rw IpAddress .1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.2.1.2 |
snNetFlowCollectorUdpPortThe NetFlow collector UDP port number.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.2.1.3 |
snNetFlowCollectorSourceInterfaceThe ifIndex value to specify source port to
export NetFlow packet. Value 0 to indicate
default outgoing port.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.2.1.4 |
snNetFlowCollectorRowStatusTo create or delete a NetFlow collector table entry.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.2.1.5 |
snNetFlowAggregationTableA table of each NetFlow aggregation scheme information. SEQUENCE OF SnNetFlowAggregationEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.3 |
snNetFlowAggregationEntryA row in the NetFlow Aggregation table. SnNetFlowAggregationEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.3.1 |
snNetFlowAggregationIndexThe Aggregation scheme IDro Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.3.1.1 |
snNetFlowAggregationIpThe NetFlow aggregation collector ip address.rw IpAddress .1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.3.1.2 |
snNetFlowAggregationUdpPortThe NetFlow aggregation collector UDP port number.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.3.1.3 |
snNetFlowAggregationSourceInterfaceThe ifIndex value to specify source port to
export NetFlow aggregation packet.
Value 0 to indicate default outgoing port.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.3.1.4 |
snNetFlowAggregationNumberOfCacheEntriesNumber of cache entries for aggregation schemerw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.3.1.5 |
snNetFlowAggregationActiveTimeoutMaximum time an active flow can be in
the aggregation cacherw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.3.1.6 |
snNetFlowAggregationInactiveTimeoutMaximum time an inactive flow can be in
the aggregation cacherw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.3.1.7 |
snNetFlowAggregationEnableEnable/disable NetFlow aggregation
for this aggregation scheme.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.3.1.8 |
snNetFlowAggregationRowStatusTo create or delete a NetFlow collector table entry.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.3.1.9 |
snNetFlowIfTableA list of interface entries. The number of entries
is given by the value of ifNumber. SEQUENCE OF SnNetFlowIfEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.4 |
snNetFlowIfEntryEntry containing the type of switching performed
on that interface. SnNetFlowIfEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.4.1 |
snNetFlowIfIndexA unique value, greater than zero, for each
interface. It is recommended that values are assigned
contiguously starting from 1. The value for each
interface sub-layer must remain constant at least from
one re-initialization of the entity's network
management system to the next re-initialization.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.4.1.1 |
snNetFlowIfFlowSwitchingTo enable/disable flow switching in a particular
interface:
disable (0) - no flow switching
enable (1) - flow switchingrw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.4.1.2 |
snSFlow OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.19 |
snSFlowGlb OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.19.1 |
snSflowCollectorTableTable of all but first sFlow collectors. The first collector can be configured
using sFlowTable in RFC 3176. The RFC cannot be used to configure more
than one sFlow collectors. This table has been created to fill this gap. SEQUENCE OF SnSflowCollectorEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.19.2 |
snSflowCollectorEntryA row in the sFlow collector table. SnSflowCollectorEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.19.2.1 |
snSflowCollectorIndexThe index to the sFlow collector table.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.19.2.1.1 |
snSflowCollectorIPThe sFlow collector ip address.rw IpAddress .1.3.6.1.4.1.11.2.3.7.11.12.1.3.19.2.1.2 |
snSflowCollectorUDPPortThe sFlow collector UDP port number.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.19.2.1.3 |
snSflowCollectorRowStatusTo create, update or delete a SFlow collector table entry.
If the row exists, then a SET with
value of create(4) returns error
'badValue'. Deleted rows go away
immediately. The following values
can be returned on reads:
noSuch(0)...no such row
other(1)....some other case
valid(2)....the row exists and is validrw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.19.2.1.4 |
snFDP OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.20 |
snFdpMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1 |
snFdpInterface OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.1 |
snFdpInterfaceTableStatus of FDP on the device's interfaces. SEQUENCE OF FdpInterfaceEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.1.1 |
snFdpInterfaceEntryAn entry in the snFdpInterfaceTable,
having the status of FDP on an interface. FdpInterfaceEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.1.1.1 |
snFdpInterfaceIfIndexifIndex value of the local interface. INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.1.1.1.1 |
snFdpInterfaceFdpEnableThe flag, whether the Foundry Discovery Protocol
is currently running on this interface. It has no
effect when FDP is disabled (snFdpGlobalRun = FALSE).rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.1.1.1.2 |
snFdpInterfaceCdpEnableThe flag, whether the Cisco Discovery Protocol
is currently running on this interface. It has no
effect when CDP is disabled (snCdpGlobalRun = FALSE).rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.1.1.1.3 |
snFdpCache OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.2 |
snFdpCacheTableThe table for the cached information obtained
via receiving FDP/CDP messages. SEQUENCE OF FdpCacheEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.2.1 |
snFdpCacheEntryAn entry in the snFdpCacheTable, having the information
received via FDP/CDP on one interface from one device.
Entries appear when a FDP/CDP advertisement is received
from a neighbor device.
Entries disappear when FDP/CDP is disabled on the interface, or globally. FdpCacheEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.2.1.1 |
snFdpCacheIfIndexifIndex value of the local interface. INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.2.1.1.1 |
snFdpCacheDeviceIndexIdentification of a device, which sent FDP/CDP messages INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.2.1.1.2 |
snFdpCacheDeviceIdThe Device-ID string as reported in the most recent FDP/CDP
message. The zero-length string indicates no Device-ID
field (TLV) was reported in the most recent FDP/CDP
message.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.2.1.1.3 |
snFdpCacheAddressTypeAn indication of the type of address contained in the
corresponding instance of snFdpCacheAddress.ro Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.2.1.1.4 |
snFdpCacheAddressThe (first) network-layer address of the device
as reported in the most recent FDP/CDP message
in the following format:
IP address: 4 octets, ip(1)
IPX address: 10 octets, ipx(2)
First 4-octet as the network number
Second 6-octet as the host number
Appletalk address: 3 octets, appletalk(3)
First 2-octet as the network number
Second 1-octet as the host numberro OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.2.1.1.5 |
snFdpCacheVersionVersion string as reported in the most recent FDP/CDP message.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.2.1.1.6 |
snFdpCacheDevicePortThe Port-ID string as reported in the most recent FDP/CDP
message. This will typically be the value of the ifName
object (e.g., Ethernet0). The zero-length string
indicates no Port-ID field (TLV) was reported in the
most recent FDP/CDP message.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.2.1.1.7 |
snFdpCachePlatformThe Device's Hardware Platform as reported in the most
recent FDP/CDP message. The zero-length string indicates
that no Platform field (TLV) was reported in the most
recent FDP/CDP message.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.2.1.1.8 |
snFdpCacheCapabilitiesThe Device's Functional Capabilities as reported in the
most recent FDP/CDP message.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.2.1.1.9 |
snFdpCacheVendorIdIndicates the entry received by either FDP or CDP.ro Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.2.1.1.10 |
snFdpCacheIsAggregateVlanNeighbor device is in aggregated-vlan.ro Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.2.1.1.11 |
snFdpCacheTagTypeNeighbor device tag-type.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.2.1.1.12 |
snFdpCachePortVlanMaskNeighbor device port VLAN masks in 512-byte octet string.ro OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.2.1.1.13 |
snFdpCachePortTagModeNeighbor device port tag modero Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.2.1.1.14 |
snFdpCacheDefaultTrafficeVlanIdForDualModeDefault traffic vlan id for neighbor device dual-mode portro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.2.1.1.15 |
snFdpGlobal OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.3 |
snFdpGlobalRunThe flag, whether the Foundry Discovery Protocol
is currently running. FDP entries in snFdpCacheTable are
deleted when FDP is disabled.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.3.1 |
snFdpGlobalMessageIntervalThe interval at which FDP messages are to be generated.
The default value is 60 seconds.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.3.2 |
snFdpGlobalHoldTimeThe time for the receiving device holds FDP message.
The default value is 180 seconds.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.3.3 |
snFdpGlobalCdpRunAn indication of whether the Cisco Discovery Protocol
is currently running. CDP entries in snFdpCacheTable are
deleted when CDP is disabled.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.3.4 |
snFdpCachedAddr OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.4 |
snFdpCachedAddressTableCached address table from receiving FDP/CDP messages. SEQUENCE OF FdpCachedAddressEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.4.1 |
snFdpCachedAddressEntryAn entry (conceptual row) in the snFdpCacheAddressTable,
containing one cached address from FDP/CDP messages. FdpCachedAddressEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.4.1.1 |
snFdpCachedAddrIfIndexThe ifIndex value of the local interface. INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.4.1.1.1 |
snFdpCachedAddrDeviceIndexA unique vlaue for each device from which FDP/CDP messages
are being received. INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.4.1.1.2 |
snFdpCachedAddrDeviceAddrEntryIndexA unique vlaue for address entry in device from which FDP/CDP messages
are being received. INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.4.1.1.3 |
snFdpCachedAddrTypeAn indication of the type of address contained in the
corresponding instance of snFdpCacheAddrValue.ro Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.4.1.1.4 |
snFdpCachedAddrValueThe network-layer address of the device
SNMP-agent as reported in the most recent FDP/CDP message
in the following format:
IP address: 4 octets, ip(1)
IPX address: 10 octets, ipx(2)
First 4-octet as the network number
Second 6-octet as the host number
Appletalk address: 3 octets, appletalk(3)
First 2-octet as the network number
Second 1-octet as the host numberro OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.4.1.1.5 |
snVsrp OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.3.21 |
snVLanByProtocolIndexThe following IP/IPX protocol VLAN types are operated
in Layer3 VLAN such as : ip(1), ipx(2), ipv6(7)
The following are operated in Layer2 bridging such as:
appleTalk(3), decNet(4), netBios(5),
others(6)
::= { snVLanByProtocolEntry 2 }
snVLanByProtocolDynamic OBJECT-TYPE
SYNTAX INTEGER {
disabled(0),
enabled(1)
}
ACCESS read-write
STATUS mandatory
DESCRIPTIONro Enumeration .snFdbEntry.6 |
snFdbRowStatusThis object is used to create and
delete row in the table and control
if they are used. The values
that can be written are:
delete(3)...deletes the row
create(4)...creates a new row
If the row exists, then a SET with
value of create(4) returns error
'badValue'. Deleted rows go away
immediately. The following values
can be returned on reads:
noSuch(0)...no such row
other(1)....some other case
valid(2)....the row exists and is validrw Enumeration .snFdbEntry.7 |