HP-SN-BGP4-GROUP-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
281
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
281 total| Object Name |
|---|
snBgp4Gen OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1 |
RFC1155-SMI Unknown .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1 |
snBgp4GenAlwaysCompareMedTo enable/disable the comparison of the Multi-Exit Discriminator for paths from
neighbors in different AS.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.1 |
snBgp4GenAutoSummaryTo enable/disable the default behavior of automatic summarization of subnet routes
into network-level routes.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.2 |
snBgp4GenDefaultLocalPreferenceTo set the default local preference attribute.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.3 |
snBgp4GenDefaultInfoOriginateTo enable/disable the default Information Originate.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.4 |
snBgp4GenFastExternalFalloverTo enable/disable an action of immediately reset the BGP sessions of any
directly adjacent external neighbors if the link used to reach them goes
down.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.5 |
snBgp4GenNextBootNeighborsThe next-boot configured number of neighbors in a BGP Peer Group.
The minimum value of this MIB is snBgp4GenMinNeighbors.
The maximum value of this MIB is snBgp4GenMaxNeighbors.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.6 |
snBgp4GenNextBootRoutesThe next-boot configured number of Routes.
The minimum value of this MIB is snBgp4GenMinRoutes.
The maximum value of this MIB is snBgp4GenMaxRoutes.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.7 |
snBgp4GenSynchronizationTo enable/disable the synchronization between BGP and your IGP.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.8 |
snBgp4GenKeepAliveTimeThe Keep alive timer.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.9 |
snBgp4GenHoldTimeThe Hold time timer.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.10 |
snBgp4GenRouterIdBGP Router Id.rw IpAddress .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.11 |
snBgp4GenTableMapAn octet string of the route-map name, each character of the name
is represented by one octet.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.12 |
snBgp4GenAdminStatThe administrative status of BGP4 in the router. The
value 'enabled' denotes that the BGP4 routing is active
in this router; 'disabled' disables BGP4 routing on this router.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.13 |
snBgp4GenDefaultMetricTo set default metric values for the BGP4 protocol.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.14 |
snBgp4GenMaxNeighborsThe maximum number of neighbors can be configured in a BGP Peer Group.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.15 |
snBgp4GenMinNeighborsThe minimum number of neighbors can be configured in a BGP Peer Group.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.16 |
snBgp4GenMaxRoutesThe maximum configured number of Routes.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.17 |
snBgp4GenMinRoutesThe minimum configured number of Routes.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.18 |
snBgp4GenMaxAddrFiltersThe maximum configured number of BGP4 address filters.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.19 |
snBgp4GenMaxAggregateAddressesThe maximum configured number of BGP4 aggregate addresses.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.20 |
snBgp4GenMaxAsPathFiltersThe maximum configured number of BGP4 AS-PATH filters.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.21 |
snBgp4GenMaxCommunityFiltersThe maximum configured number of BGP4 Community filters.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.22 |
snBgp4GenMaxNetworksThe maximum configured number of BGP4 Networks.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.23 |
snBgp4GenMaxRouteMapFiltersThe maximum configured number of BGP4 Route-map Filters.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.24 |
snBgp4GenNeighPrefixMinValueThe minimum configured value of BGP4 Neighbor Prefix.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.25 |
snBgp4GenOperNeighborsThe current operational max number of neighbors configured for a BGP Group.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.26 |
snBgp4GenOperRoutesThe current operational number of Routes.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.27 |
snBgp4GenLocalAsBgp4 local autonomous system number.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.28 |
snBgp4GenRoutesInstalledBgp4 installed routes.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.29 |
snBgp4GenAsPathInstalledBgp4 installed autonomous system path.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.30 |
snBgp4ExternalDistanceAdministrative distance for BGP external routes.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.31 |
snBgp4InternalDistanceAdministrative distance for BGP internal routes.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.32 |
snBgp4LocalDistanceAdministrative distance for BGP local routes.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.33 |
snBgp4OperNumOfAttributesThe operational number of attribute entries.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.34 |
snBgp4NextBootMaxAttributesThe next boot maximum attribute entries. 10000 means reset to default.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.35 |
snBgp4ClusterIdA cluster ID which is represented by 4 bytes unsigned
integer (0..0xFFFFFFFF). 0 means reset to default.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.36 |
snBgp4ClientToClientReflectionTo enable/disable the client to client reflection in BGP4.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.37 |
snBgp4GenTotalNeighborsThe current total number of neighbors running in a BGP Group.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.38 |
snBgp4GenMaxPathsThe maximum configured number of Paths.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.39 |
snBgp4GenConfedIdBgp4 Confederation Id.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.40 |
snBgp4GenConfedPeersAn AS number from 1 to 0xFFFF construct confederation peers.
There are 50(max peers) of them.
This integer number is represented by 2 OCTETs.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.41 |
snBgp4GenDampeningThe dampening of BGP4 in the router.
value 'none' denotes that the BGP4 dampening is off
'parameters' denotes parameters are confibrurable.
'routeMap' denotes routemap is configurable.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.42 |
snBgp4GenDampenHalfLifeBgp4 Dampening Half Life.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.43 |
snBgp4GenDampenReuseBgp4 Dampening Reuse.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.44 |
snBgp4GenDampenSuppressBgp4 Dampening Suppress.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.45 |
snBgp4GenDampenMaxSuppressBgp4 Dampening Max Suppress Time.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.46 |
snBgp4GenDampenMapAn octet string of the route-map name for dampening, each character of the name
is represented by one octet.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.47 |
snBgp4AddrFilter OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.2 |
snBgp4AddrFilterTableBgp4 Address Filter table. SEQUENCE OF SnBgp4AddrFilterEntry .1.3.6.1.4.1.11.2.3.7.11.12.2.11.2.1 |
snBgp4AddrFilterEntryAn entry in the Bgp4 Address Filter table. SnBgp4AddrFilterEntry .1.3.6.1.4.1.11.2.3.7.11.12.2.11.2.1.1 |
snBgp4AddrFilterIndexThe table index for a filter entry.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.2.1.1.1 |
snBgp4AddrFilterActionAction to take if the bgp address match
with this filter.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.2.1.1.2 |
snBgp4AddrFilterSourceIpSource IP address.rw IpAddress .1.3.6.1.4.1.11.2.3.7.11.12.2.11.2.1.1.3 |
snBgp4AddrFilterSourceMaskSource IP subnet mask.rw IpAddress .1.3.6.1.4.1.11.2.3.7.11.12.2.11.2.1.1.4 |
snBgp4AddrFilterDestIpDestination IP address.rw IpAddress .1.3.6.1.4.1.11.2.3.7.11.12.2.11.2.1.1.5 |
snBgp4AddrFilterDestMaskDestination IP subnet mask.rw IpAddress .1.3.6.1.4.1.11.2.3.7.11.12.2.11.2.1.1.6 |
snBgp4AddrFilterRowStatusThis object is used to create and
delete row in the table and control
if they are used. The values
that can be written are:
delete(3)...deletes the row
create(4)...creates a new row
modify(5)...modifies an exsisting row
If the row exists, then a SET with
value of create(4) returns error
'badValue'. Deleted rows go away
immediately. The following values
can be returned on reads:
noSuch(0)...no such row
invalid(1)...Setting it to 'invalid' has the effect of
rendering it inoperative..
valid(2)....the row exists and is validrw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.2.1.1.7 |
snBgp4AggregateAddr OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.3 |
snBgp4AggregateAddrTableBgp4 Aggregate Address table. SEQUENCE OF SnBgp4AggregateAddrEntry .1.3.6.1.4.1.11.2.3.7.11.12.2.11.3.1 |
snBgp4AggregateAddrEntryAn entry in the Bgp4 Aggregate Address table. SnBgp4AggregateAddrEntry .1.3.6.1.4.1.11.2.3.7.11.12.2.11.3.1.1 |
snBgp4AggregateAddrIpAggregate Address IP address.ro IpAddress .1.3.6.1.4.1.11.2.3.7.11.12.2.11.3.1.1.1 |
snBgp4AggregateAddrMaskAggregate Address IP subnet mask.ro IpAddress .1.3.6.1.4.1.11.2.3.7.11.12.2.11.3.1.1.2 |
snBgp4AggregateAddrOptionaddress(1), asSet(2), summaryOnly(3),
the suppressMap(4), advertiseMap(5),
attributeMap(6) are Options for creating an aggregate entry
in a BGP routing table.ro Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.3.1.1.3 |
snBgp4AggregateAddrMapThis object associates with the snBgp4AggregateAddrOption and
the suppressMap(4), advertiseMap(5), attributeMap(6) of the
snBgp4AggregateAddrOption are only two Options for creating
an aggregate address map. A SNMP-SET error will be returned
for other options. An octet string of the map name,
each character of the name is represented by one octet.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.3.1.1.4 |
snBgp4AggregateAddrRowStatusThis object is used to create and
delete row in the table and control
if they are used. The values
that can be written are:
delete(3)...deletes the row
create(4)...creates a new row
modify(5)...modifies an exsisting row
If the row exists, then a SET with
value of create(4) returns error
'badValue'. Deleted rows go away
immediately. The following values
can be returned on reads:
noSuch(0)...no such row
invalid(1)...Setting it to 'invalid' has the effect of
rendering it inoperative..
valid(2)....the row exists and is validrw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.3.1.1.5 |
snBgp4AsPathFilter OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.4 |
snBgp4AsPathFilterTableBgp4 AS-Path Filter table. SEQUENCE OF SnBgp4AsPathFilterEntry .1.3.6.1.4.1.11.2.3.7.11.12.2.11.4.1 |
snBgp4AsPathFilterEntryAn entry in the Bgp4 As-path Filter table. SnBgp4AsPathFilterEntry .1.3.6.1.4.1.11.2.3.7.11.12.2.11.4.1.1 |
snBgp4AsPathFilterIndexThe table index for a filter entry.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.4.1.1.1 |
snBgp4AsPathFilterActionAction to take if the bgp address match
with this filter.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.4.1.1.2 |
snBgp4AsPathFilterRegExpressionAutonomous system in the filter using a regular expression.
Each character of the regular expression string is represented
by one octet.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.4.1.1.3 |
snBgp4AsPathFilterRowStatusThis object is used to create and
delete row in the table and control
if they are used. The values
that can be written are:
delete(3)...deletes the row
create(4)...creates a new row
modify(5)...modifies an exsisting row
If the row exists, then a SET with
value of create(4) returns error
'badValue'. Deleted rows go away
immediately. The following values
can be returned on reads:
noSuch(0)...no such row
invalid(1)...Setting it to 'invalid' has the effect of
rendering it inoperative..
valid(2)....the row exists and is validrw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.4.1.1.4 |
snBgp4CommunityFilter OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.5 |
snBgp4CommunityFilterTableBgp4 Community Filter table. SEQUENCE OF SnBgp4CommunityFilterEntry .1.3.6.1.4.1.11.2.3.7.11.12.2.11.5.1 |
snBgp4CommunityFilterEntryAn entry in the Bgp4 Community Filter table. SnBgp4CommunityFilterEntry .1.3.6.1.4.1.11.2.3.7.11.12.2.11.5.1.1 |
snBgp4CommunityFilterIndexThe table index for a filter entry.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.5.1.1.1 |
snBgp4CommunityFilterActionAction to take if the bgp address match
with this filter.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.5.1.1.2 |
snBgp4CommunityFilterCommNumA number from 1 to 0xFFFFFFFF. There are 20 of them.
This integer number is represented by 4 OCTETs.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.5.1.1.3 |
snBgp4CommunityFilterInternetDisabled/Enabled the Internet Community.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.5.1.1.4 |
snBgp4CommunityFilterNoAdvertiseDo not advertise this route to any peer (internal or external).rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.5.1.1.5 |
snBgp4CommunityFilterNoExportDo not advertise this route to an EBGP peer.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.5.1.1.6 |
snBgp4CommunityFilterRowStatusThis object is used to create and
delete row in the table and control
if they are used. The values
that can be written are:
delete(3)...deletes the row
create(4)...creates a new row
modify(5)...modifies an exsisting row
If the row exists, then a SET with
value of create(4) returns error
'badValue'. Deleted rows go away
immediately. The following values
can be returned on reads:
noSuch(0)...no such row
invalid(1)...Setting it to 'invalid' has the effect of
rendering it inoperative..
valid(2)....the row exists and is validrw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.5.1.1.7 |
snBgp4CommunityFilterLocalAsSend this route to peers in other sub-autonomous systems within
the local confederation. Do not advertise this route to an
external system.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.5.1.1.8 |
snBgp4NeighGenCfg OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.6 |
snBgp4NeighGenCfgTableBgp4 Neighbor General Configuration table. SEQUENCE OF SnBgp4NeighGenCfgEntry .1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1 |
snBgp4NeighGenCfgEntryAn entry in the Bgp4 Community Filter table. SnBgp4NeighGenCfgEntry .1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1 |
snBgp4NeighGenCfgNeighIpThe IP Address for a neighbor entry.ro IpAddress .1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.1 |
snBgp4NeighGenCfgAdvertlevelTo set the minimum interval between the
sending of BGP routing updates.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.2 |
snBgp4NeighGenCfgDefOriginateTo enable/disable the default originate for this neighbor.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.3 |
snBgp4NeighGenCfgEbgpMultihopTo enable/disable the EBGP Muitihop for this neighbor.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.4 |
snBgp4NeighGenCfgMaxPrefixTo control how many prefixes can be received from a neighbor.
The minimum value of the maximum prefix is snBgp4GenNeighPrefixMinValue.
The maximum value of the maximum prefix is snBgp4GenOperRoutes.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.5 |
snBgp4NeighGenCfgNextHopSelfTo enable/disable the next-hop processing of BGP updates on the router.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.6 |
snBgp4NeighGenCfgRemoteAsTo specify a neighbor with an autonomous system number(AS).rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.7 |
snBgp4NeighGenCfgSendCommTo specify that a COMMUNITES attribute should be sent to a BGP neighbor.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.8 |
snBgp4NeighGenCfgWeightTo assign a weight to a neighbor connection.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.9 |
snBgp4NeighGenCfgWeightFilterListA number from 1 to 0xFFFF. There are 16 of them.
This integer number is represented by 2 OCTETs.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.10 |
snBgp4NeighGenCfgRowStatusThis object is used to create and
delete row in the table and control
if they are used. The values
that can be written are:
delete(3)...deletes the row
create(4)...creates a new row
modify(5)...modifies an exsisting row
applyDefault(6)...apply default value to an exsisting row
If the row exists, then a SET with
value of create(4) returns error
'badValue'. Deleted rows go away
immediately. The following values
can be returned on reads:
noSuch(0)...no such row
invalid(1)...Setting it to 'invalid' has the effect of
rendering it inoperative..
valid(2)....the row exists and is validrw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.11 |
snBgp4NeighGenCfgUpdateSrcLpbIntfTo allow internal BGP sessions to use any operational
loopback interface (1..8) for TCP connections. Zero
interface means to restore the interface assignment to the
closest interface, which is called the best local address.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.12 |
snBgp4NeighGenCfgRouteRefClientTo configure the router as a BGP route reflector,
enable the specified neighbor as its client.
When all the clients are disabled, the local router
is no longer a route reflector.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.13 |
snBgp4NeighGenCfgRemovePrivateAsTo enable/disable filtering private AS number.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.14 |
snBgp4NeighGenCfgEbgpMultihopTtlThe EBGP Muitihop TTL for this neighbor.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.15 |
snBgp4NeighGenCfgShutdownTo enable/disable BGP4 Nbr Shutdown.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.16 |
snBgp4NeighGenCfgKeepAliveTimeThe Keep alive timer.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.17 |
snBgp4NeighGenCfgHoldTimeThe Hold time timer.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.18 |
snBgp4NeighGenCfgDefOrigMapAn octet string of the route-map name, each character of the name
is represented by one octet.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.19 |
snBgp4NeighGenCfgDescAn octet string of the neighbor description.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.20 |
snBgp4NeighGenCfgPassAn octet string of the neighbor Md5 password.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.21 |
snBgp4NeighDistGroup OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.7 |
snBgp4NeighDistGroupTableBgp4 Neighbor Distribute Group table. SEQUENCE OF SnBgp4NeighDistGroupEntry .1.3.6.1.4.1.11.2.3.7.11.12.2.11.7.1 |
snBgp4NeighDistGroupEntryAn entry in the Bgp4 Distribute Group table. SnBgp4NeighDistGroupEntry .1.3.6.1.4.1.11.2.3.7.11.12.2.11.7.1.1 |
snBgp4NeighDistGroupNeighIpThe IP Address for a neighbor entry.ro IpAddress .1.3.6.1.4.1.11.2.3.7.11.12.2.11.7.1.1.1 |
snBgp4NeighDistGroupDirThe incoming/outgoing advertisements to which
the access list is applied.ro Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.7.1.1.2 |
snBgp4NeighDistGroupAccessListA number from 1 to 0xFFFF. There are 16 of them.
This integer number is represented by 2 OCTETs.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.7.1.1.3 |
snBgp4NeighDistGroupRowStatusThis object is used to create and
delete row in the table and control
if they are used. The values
that can be written are:
delete(3)...deletes the row
create(4)...creates a new row
modify(5)...modifies an exsisting row
If the row exists, then a SET with
value of create(4) returns error
'badValue'. Deleted rows go away
immediately. The following values
can be returned on reads:
noSuch(0)...no such row
invalid(1)...Setting it to 'invalid' has the effect of
rendering it inoperative..
valid(2)....the row exists and is validrw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.7.1.1.4 |
snBgp4NeighDistGroupInFilterListA number from 1 to 0xFFFF. There are 16 of them.
This integer number is represented by 2 OCTETs.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.7.1.1.5 |
snBgp4NeighDistGroupOutFilterListA number from 1 to 0xFFFF. There are 16 of them.
This integer number is represented by 2 OCTETs.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.7.1.1.6 |
snBgp4NeighDistGroupInIpAccessListA number from 1 to 0xFFFF. There are 1 of them.
This integer number is represented by 2 OCTETs.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.7.1.1.7 |
snBgp4NeighDistGroupOutIpAccessListA number from 1 to 0xFFFF. There are 1 of them.
This integer number is represented by 2 OCTETs.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.7.1.1.8 |
snBgp4NeighDistGroupInPrefixListA Prefix name list.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.7.1.1.9 |
snBgp4NeighDistGroupOutPrefixListA Prefix name list.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.7.1.1.10 |
snBgp4NeighFilterGroup OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.8 |
snBgp4NeighFilterGroupTableBgp4 Neighbor Filter Group table. SEQUENCE OF SnBgp4NeighFilterGroupEntry .1.3.6.1.4.1.11.2.3.7.11.12.2.11.8.1 |
snBgp4NeighFilterGroupEntryAn entry in the Bgp4 Neighbor Filter Group table. SnBgp4NeighFilterGroupEntry .1.3.6.1.4.1.11.2.3.7.11.12.2.11.8.1.1 |
snBgp4NeighFilterGroupNeighIpThe IP Address for a neighbor entry.ro IpAddress .1.3.6.1.4.1.11.2.3.7.11.12.2.11.8.1.1.1 |
snBgp4NeighFilterGroupDirThe incoming/outgoing advertisements to which
the access list is applied.ro Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.8.1.1.2 |
snBgp4NeighFilterGroupAccessListA number from 1 to 0xFFFF. There are 16 of them.
This integer number is represented by 2 OCTETs.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.8.1.1.3 |
snBgp4NeighFilterGroupRowStatusThis object is used to create and
delete row in the table and control
if they are used. The values
that can be written are:
delete(3)...deletes the row
create(4)...creates a new row
modify(5)...modifies an exsisting row
If the row exists, then a SET with
value of create(4) returns error
'badValue'. Deleted rows go away
immediately. The following values
can be returned on reads:
noSuch(0)...no such row
invalid(1)...Setting it to 'invalid' has the effect of
rendering it inoperative..
valid(2)....the row exists and is validrw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.8.1.1.4 |
snBgp4NeighFilterGroupInFilterListA number from 1 to 0xFFFF. There are 16 of them.
This integer number is represented by 2 OCTETs.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.8.1.1.5 |
snBgp4NeighFilterGroupOutFilterListA number from 1 to 0xFFFF. There are 16 of them.
This integer number is represented by 2 OCTETs.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.8.1.1.6 |
snBgp4NeighFilterGroupInAsPathAccessListA number from 1 to 0xFFFF. There are 1 of them.
This integer number is represented by 2 OCTETs.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.8.1.1.7 |
snBgp4NeighFilterGroupOutAsPathAccessListA number from 1 to 0xFFFF. There are 1 of them.
This integer number is represented by 2 OCTETs.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.8.1.1.8 |
snBgp4NeighFilterGroupWeightTo assign a weight to a neighbor filter.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.8.1.1.9 |
snBgp4NeighFilterGroupWeightAccessListA number from 1 to 0xFFFF. There are 1 of them.
This integer number is represented by 2 OCTETs.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.8.1.1.10 |
snBgp4NeighRouteMap OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.9 |
snBgp4NeighRouteMapTableBgp4 Neighbor Route Map table. SEQUENCE OF SnBgp4NeighRouteMapEntry .1.3.6.1.4.1.11.2.3.7.11.12.2.11.9.1 |
snBgp4NeighRouteMapEntryAn entry in the Bgp4 Route Map table. SnBgp4NeighRouteMapEntry .1.3.6.1.4.1.11.2.3.7.11.12.2.11.9.1.1 |
snBgp4NeighRouteMapNeighIpThe IP Address for a neighbor entry.ro IpAddress .1.3.6.1.4.1.11.2.3.7.11.12.2.11.9.1.1.1 |
snBgp4NeighRouteMapDirThe incoming/outgoing advertisements to which
the access list is applied.ro Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.9.1.1.2 |
snBgp4NeighRouteMapMapNameAn octet string of the route-map name, Each character of the name
is represented by one octet.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.9.1.1.3 |
snBgp4NeighRouteMapRowStatusThis object is used to create and
delete row in the table and control
if they are used. The values
that can be written are:
delete(3)...deletes the row
create(4)...creates a new row
modify(5)...modifies an exsisting row
If the row exists, then a SET with
value of create(4) returns error
'badValue'. Deleted rows go away
immediately. The following values
can be returned on reads:
noSuch(0)...no such row
invalid(1)...Setting it to 'invalid' has the effect of
rendering it inoperative..
valid(2)....the row exists and is validrw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.9.1.1.4 |
snBgp4Network OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.10 |
snBgp4NetworkTableBgp4 Network Weight table. SEQUENCE OF SnBgp4NetworkEntry .1.3.6.1.4.1.11.2.3.7.11.12.2.11.10.1 |
snBgp4NetworkEntryAn entry in the Bgp4 Network Weight table. SnBgp4NetworkEntry .1.3.6.1.4.1.11.2.3.7.11.12.2.11.10.1.1 |
snBgp4NetworkIpThe IP Address for a network entry.ro IpAddress .1.3.6.1.4.1.11.2.3.7.11.12.2.11.10.1.1.1 |
snBgp4NetworkSubnetMaskThe subnet mask for a network entry.ro IpAddress .1.3.6.1.4.1.11.2.3.7.11.12.2.11.10.1.1.2 |
snBgp4NetworkWeightTo assign a weight to a neighbor connection.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.10.1.1.3 |
snBgp4NetworkBackdoorTo enable/disable the backdoor for this network.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.10.1.1.4 |
snBgp4NetworkRowStatusThis object is used to create and
delete row in the table and control
if they are used. The values
that can be written are:
delete(3)...deletes the row
create(4)...creates a new row
modify(5)...modifies an exsisting row
If the row exists, then a SET with
value of create(4) returns error
'badValue'. Deleted rows go away
immediately. The following values
can be returned on reads:
noSuch(0)...no such row
invalid(1)...Setting it to 'invalid' has the effect of
rendering it inoperative..
valid(2)....the row exists and is validrw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.10.1.1.5 |
snBgp4Redis OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.11 |
snBgp4RedisTableThe BGP4 Redistribution contains configurations
that could be imported into the BGP4 domain. SEQUENCE OF SnBgp4RedisEntry .1.3.6.1.4.1.11.2.3.7.11.12.2.11.11.1 |
snBgp4RedisEntryThe BGP4 Redistribution Entry specifies a particular RIP
or , OSPF, or Static route to be imported into the BGP4 domain. SnBgp4RedisEntry .1.3.6.1.4.1.11.2.3.7.11.12.2.11.11.1.1 |
snBgp4RedisProtocolThe imported configuration into BGP4 domain is set in the following:
rip(1): - the RIP.
ospf(2): - the OSPF.
static(3): - the static.
connected(4): - the connected.
isis(5): - the ISIS.ro Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.11.1.1.1 |
snBgp4RedisMetricThe metric of using the specified protocol Metric value.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.11.1.1.2 |
snBgp4RedisRouteMapAn octet string of the route-map name, each character of the name
is represented by one octet.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.11.1.1.3 |
snBgp4RedisWeightTo assign a weight for the specified protocol.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.11.1.1.4 |
snBgp4RedisMatchInternalThis object is only applicable to the OSPF protocol.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.11.1.1.5 |
snBgp4RedisMatchExternal1This object is only applicable to the OSPF protocol.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.11.1.1.6 |
snBgp4RedisMatchExternal2This object is only applicable to the OSPF protocol.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.11.1.1.7 |
snBgp4RedisRowStatusThis object is used to create and
delete row in the table and control
if they are used. The values
that can be written are:
delete(3)...deletes the row
create(4)...creates a new row
modify(5)...modifies an exsisting row
If the row exists, then a SET with
value of create(4) returns error
'badValue'. Deleted rows go away
immediately. The following values
can be returned on reads:
noSuch(0)...no such row
invalid(1)...Setting it to 'invalid' has the effect of
rendering it inoperative..
valid(2)....the row exists and is validrw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.11.1.1.8 |
snBgp4RouteMapFilter OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.12 |
snBgp4RouteMapFilterTableBgp4 RouteMap Filter table. SEQUENCE OF SnBgp4RouteMapFilterEntry .1.3.6.1.4.1.11.2.3.7.11.12.2.11.12.1 |
snBgp4RouteMapFilterEntryAn entry in the Bgp4 RouteMap Filter table. SnBgp4RouteMapFilterEntry .1.3.6.1.4.1.11.2.3.7.11.12.2.11.12.1.1 |
snBgp4RouteMapFilterMapNameAn octet string of the route-map name, each character of the name
is represented by one octet.ro OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.12.1.1.1 |
snBgp4RouteMapFilterSequenceNumA sequence number for this particular route-map.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.12.1.1.2 |
snBgp4RouteMapFilterActionAction to take if the bgp address match
with this filter.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.12.1.1.3 |
snBgp4RouteMapFilterRowStatusThis object is used to create and
delete row in the table and control
if they are used. The values
that can be written are:
delete(3)...deletes the row
create(4)...creates a new row
modify(5)...modifies an exsisting row
If the row exists, then a SET with
value of create(4) returns error
'badValue'. Deleted rows go away
immediately. The following values
can be returned on reads:
noSuch(0)...no such row
invalid(1)...Setting it to 'invalid' has the effect of
rendering it inoperative..
valid(2)....the row exists and is validrw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.12.1.1.4 |
snBgp4RouteMapMatch OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.13 |
snBgp4RouteMapMatchTableBgp4 Route Map Set table. SEQUENCE OF SnBgp4RouteMapMatchEntry .1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1 |
snBgp4RouteMapMatchEntryAn entry in the Bgp4 Route Map Match table. SnBgp4RouteMapMatchEntry .1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1 |
snBgp4RouteMapMatchMapNameAn octet string of the route-map name, each character of the name
is represented by one octet.ro OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1.1 |
snBgp4RouteMapMatchSequenceNumA sequence number for this particular route-map.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1.2 |
snBgp4RouteMapMatchAsPathFilterA number from 1 to 0xFFFF and there are 10 of 2 OCTETs.
This integer number is represented by 2 OCTETs.
To match a BGP autonomous system path access list.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1.3 |
snBgp4RouteMapMatchCommunityFilterA number from 1 to 0xFFFF and there are 10 of 2 OCTETs.
This integer number is represented by 2 OCTETs.
To match a BGP community access list.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1.4 |
snBgp4RouteMapMatchAddressFilterA number from 1 to 0xFFFF and there are 10 of 2 OCTETs.
This integer number is represented by 2 OCTETs.
To match a BGP address access list.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1.5 |
snBgp4RouteMapMatchMetricTo match a metric for BGP routes.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1.6 |
snBgp4RouteMapMatchNextHopListA number from 1 to 0xFFFF and there are 16 of 2 OCTETs.
This integer number is represented by 2 OCTETs.
To match a BGP next-hop access list.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1.7 |
snBgp4RouteMapMatchRouteTypeTo match a route-type.
Currently only externalType1(2),
externalType2(3), internal(4) is supported for SNMP-SET.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1.8 |
snBgp4RouteMapMatchTagListTo match a BGP tag access list.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1.9 |
snBgp4RouteMapMatchRowMaskThis object is used together with above
MIBs in the same VARBIND to set and
reset any MIBs in the table.
The bit number is referred to the
snBgp4RouteMapMatchEntry number
of each row in the table.
The bit is ON - means set,
The bit is OFF - means resetrw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1.10 |
snBgp4RouteMapMatchAsPathAccessListA number from 1 to 0xFFFFFFFF and there are 5 of 4 OCTETs.
This integer number is represented by 4 OCTETs.
To match a BGP autonomous system path access list.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1.11 |
snBgp4RouteMapMatchCommunityListA number from 1 to 0xFFFFFFFF and there are 5 of 4 OCTETs.
This integer number is represented by 4 OCTETs.
To match a BGP community access list.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1.12 |
snBgp4RouteMapMatchAddressAccessListA number from 1 to 0xFFFF and there are 5 of 2 OCTETs.
This integer number is represented by 2 OCTETs.
To match a BGP address access list.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1.13 |
snBgp4RouteMapMatchAddressPrefixListPrefix list
To match a BGP address access list.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1.14 |
snBgp4RouteMapMatchNextHopAccessListA number from 1 to 0xFFFF and there are 5 of 2 OCTETs.
This integer number is represented by 2 OCTETs.
To match a BGP address access list.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1.15 |
snBgp4RouteMapMatchNextHopPrefixListPrefix list
To match a BGP address access list.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1.16 |
snBgp4RouteMapSet OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.14 |
snBgp4RouteMapSetTableBgp4 Route Map Set table. SEQUENCE OF SnBgp4RouteMapSetEntry .1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1 |
snBgp4RouteMapSetEntryAn entry in the Bgp4 Route Map Set table. SnBgp4RouteMapSetEntry .1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1 |
snBgp4RouteMapSetMapNameAn octet string of the route-map name, each character of the name
is represented by one octet.ro OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.1 |
snBgp4RouteMapSetSequenceNumA sequence number for this particular route-map.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.2 |
snBgp4RouteMapSetAsPathTypeTo modify an autonomous system path for BGP routes.
tag(0) - Converts the tag of a route into an autonomous system path.
prepend(1) - Appends the string from snBgp4RouteMapSetAsPathString to the
as-path of the route that is matched by the route map.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.3 |
snBgp4RouteMapSetAsPathStringas-path string. This string is used if only if the snBgp4RouteMapSetAsPathCmd
was sent together with the value set to prepend(1).rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.4 |
snBgp4RouteMapSetAutoTagTo enable/disable the automatic-tag for BGP routes.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.5 |
snBgp4RouteMapSetCommunityTypeTo set the BGP COMMUNITIES attribute. none means no other
community attributes are allowed, nums means allowing community
attributesi, the old values 1 and 2 are not valid since 5.03.00rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.6 |
snBgp4RouteMapSetCommunityNumcommunity-number. This number is used if only if the snBgp4RouteMapSetCommunityCmd
was sent together with the value set to number(0).rwdeprecated INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.7 |
snBgp4RouteMapSetCommunityAdditiveTo add the community to the already existing communities.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.8 |
snBgp4RouteMapSetLocalPreferenceTo modify a local-preference for BGP routes.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.9 |
snBgp4RouteMapSetMetricTo modify a metric for BGP routes.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.10 |
snBgp4RouteMapSetNextHopTo modify the IP address of the next hop for BGP routes.rw IpAddress .1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.11 |
snBgp4RouteMapSetOriginTo set the BGP origin code.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.12 |
snBgp4RouteMapSetTagTo specify the tag for BGP routes.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.13 |
snBgp4RouteMapSetWeightTo specify the BGP weight for the routing table.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.14 |
snBgp4RouteMapSetRowMaskThis object is used together with above
MIBs in the same VARBIND to set and
reset any MIBs in the table.
The bit number is referred to the
snBgp4RouteMapSetEntry number
of each row in the table.
The bit is ON - means set,
The bit is OFF - means resetrw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.15 |
snBgp4RouteMapSetCommunityNumsCommunity number is from 1 to 0xFFFFFFFF. There are 6 of them.
This integer number is represented by 4 OCTETs.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.16 |
snBgp4RouteMapSetDampenHalfLifeBgp4 Route Map Dampening Half Life.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.17 |
snBgp4RouteMapSetDampenReuseBgp4 Route Map Dampening Reuse.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.18 |
snBgp4RouteMapSetDampenSuppressBgp4 Route Map Dampening Suppress.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.19 |
snBgp4RouteMapSetDampenMaxSuppressBgp4 Route Map Dampening Max Suppress Time.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.20 |
snBgp4NeighOperStatus OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.15 |
snBgp4NeighOperStatusTableBgp4 Neighbor Operational Status table. SEQUENCE OF SnBgp4NeighOperStatusEntry .1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1 |
snBgp4NeighOperStatusEntryAn entry in the Bgp4 Operational Status table. SnBgp4NeighOperStatusEntry .1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1 |
snBgp4NeighOperStatusIndexThe index for a neighbor entry.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.1 |
snBgp4NeighOperStatusIpThe IP Address for a neighbor entry.ro IpAddress .1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.2 |
snBgp4NeighOperStatusRemoteAsTo show a neighbor with an autonomous system number(AS).ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.3 |
snBgp4NeighOperStatusBgpTypeTo show the type of BGP protocol whether is internal or external.ro Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.4 |
snBgp4NeighOperStatusStateTo show the state of this neighbor.ro Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.5 |
snBgp4NeighOperStatusKeepAliveTimeThe Keep alive timer.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.6 |
snBgp4NeighOperStatusHoldTimeThe Hold time timer.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.7 |
snBgp4NeighOperStatusAdvertlevelTo show the minimum interval between the
sending of BGP routing updates.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.8 |
snBgp4NeighOperStatusKeepAliveTxCountsKeep alive message sent counts.ro Counter .1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.9 |
snBgp4NeighOperStatusKeepAliveRxCountsKeep alive message received counts.ro Counter .1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.10 |
snBgp4NeighOperStatusUpdateTxCountsUpdate message sent counts.ro Counter .1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.11 |
snBgp4NeighOperStatusUpdateRxCountsUpdate message received counts.ro Counter .1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.12 |
snBgp4NeighOperStatusNotifTxCountsNotification message sent counts.ro Counter .1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.13 |
snBgp4NeighOperStatusNotifRxCountsNotification message received counts.ro Counter .1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.14 |
snBgp4NeighOperStatusOpenTxCountsOpen message sent counts.ro Counter .1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.15 |
snBgp4NeighOperStatusOpenRxCountsOpen message received counts.ro Counter .1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.16 |
snBgp4RouteOperStatus OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.16 |
snBgp4RouteOperStatusTableBgp4 Routebor Operational Status table. SEQUENCE OF SnBgp4RouteOperStatusEntry .1.3.6.1.4.1.11.2.3.7.11.12.2.11.16.1 |
snBgp4RouteOperStatusEntryAn entry in the Bgp4 Operational Status table. SnBgp4RouteOperStatusEntry .1.3.6.1.4.1.11.2.3.7.11.12.2.11.16.1.1 |
snBgp4RouteOperStatusIndexThe index for a route entry.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.16.1.1.1 |
snBgp4RouteOperStatusIpThe IP Address for a route entry.ro IpAddress .1.3.6.1.4.1.11.2.3.7.11.12.2.11.16.1.1.2 |
snBgp4RouteOperStatusSubnetMaskThe IP Subnet Mask for a route entry.ro IpAddress .1.3.6.1.4.1.11.2.3.7.11.12.2.11.16.1.1.3 |
snBgp4RouteOperStatusNextHopThe next-hop IP for a route entry.ro IpAddress .1.3.6.1.4.1.11.2.3.7.11.12.2.11.16.1.1.4 |
snBgp4RouteOperStatusMetricTo show the metric value of a route entry.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.16.1.1.5 |
snBgp4RouteOperStatusLocalPreferenceTo show the local preference of a route entry.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.16.1.1.6 |
snBgp4RouteOperStatusWeightTo show the weight of this route.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.16.1.1.7 |
snBgp4RouteOperStatusOriginTo show the origin of this route.ro Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.16.1.1.8 |
snBgp4RouteOperStatusStatusA bit array that contains the status of this route.
This is a packed bit string; The following shows the
meaning of each bit:
(bit 0 is the least significant bit and 0=FALSE, 1=TRUE).
bit position meaning
6-31 reserved.
5 aggregate.
4 best.
3 internal.
2 local.
1 suppressed.
0 valid.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.16.1.1.9 |
snBgp4RouteOperStatusRouteTagTo show the route tag of this route.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.16.1.1.10 |
snBgp4RouteOperStatusCommunityListTo show the community list of this route.
If the community list is an NULL string that means an empty list, then
the community is INTERNET. A number from 1 to 0xFFFFFFFF.
This integer number is represented by 4 OCTETs.
In the community list, it could have some Well-known numbers such as:
BGP_COMMUNITY_ATTRIBUTE_NO_EXPORT 0xFFFFFF01
BGP_COMMUNITY_ATTRIBUTE_NO_ADVERTISE 0xFFFFFF02ro OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.16.1.1.11 |
snBgp4RouteOperStatusAsPathListTo show the AS Path list of this route.
A number from 1 to 0xFFFF.
This integer number is represented by 2 OCTETs.ro OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.16.1.1.12 |
snBgp4NeighborSummary OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.17 |
snBgp4NeighborSummaryTableBgp4 Routebor Operational Status table. SEQUENCE OF SnBgp4NeighborSummaryEntry .1.3.6.1.4.1.11.2.3.7.11.12.2.11.17.1 |
snBgp4NeighborSummaryEntryAn entry in the Bgp4 Operational Status table. SnBgp4NeighborSummaryEntry .1.3.6.1.4.1.11.2.3.7.11.12.2.11.17.1.1 |
snBgp4NeighborSummaryIndexThe index for a route entry.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.17.1.1.1 |
snBgp4NeighborSummaryIpThe IP Address for a route entry.ro IpAddress .1.3.6.1.4.1.11.2.3.7.11.12.2.11.17.1.1.2 |
snBgp4NeighborSummaryStateTo show the state of this neighbor.ro Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.17.1.1.3 |
snBgp4NeighborSummaryStateChgTimeThe time of a change of the state of this neighbor.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.17.1.1.4 |
snBgp4NeighborSummaryRouteReceivedThe number of routes received of this neighbor.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.17.1.1.5 |
snBgp4NeighborSummaryRouteInstalledThe number of routes installed of this neighbor.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.17.1.1.6 |
snBgp4Attribute OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.18 |
snBgp4AttributeTableBgp4 Attribute entries table. SEQUENCE OF SnBgp4AttributeEntry .1.3.6.1.4.1.11.2.3.7.11.12.2.11.18.1 |
snBgp4AttributeEntryAn entry in the Bgp4 Attribute table. SnBgp4AttributeEntry .1.3.6.1.4.1.11.2.3.7.11.12.2.11.18.1.1 |
snBgp4AttributeIndexThe index for a route entry.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.18.1.1.1 |
snBgp4AttributeNextHopThe next-hop IP for a route entry.ro IpAddress .1.3.6.1.4.1.11.2.3.7.11.12.2.11.18.1.1.2 |
snBgp4AttributeMetricTo show the metric value of a route entry.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.18.1.1.3 |
snBgp4AttributeOriginTo show the origin of this route.ro Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.18.1.1.4 |
snBgp4AttributeAggregatorAsThe aggregator AS number for an attribute entry.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.18.1.1.5 |
snBgp4AttributeRouterIdThe router ID for an attribute entry.ro IpAddress .1.3.6.1.4.1.11.2.3.7.11.12.2.11.18.1.1.6 |
snBgp4AttributeAtomicAggregatePresentThe atomic aggregate present in an attribute entry.ro Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.18.1.1.7 |
snBgp4AttributeLocalPreferenceTo show the local preference of a route entry.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.18.1.1.8 |
snBgp4AttributeCommunityListTo show the community list of this attribute entry.
If the community list is an NULL string that means an empty list, then
the community is INTERNET. A number from 1 to 0xFFFFFFFF.
This integer number is represented by 4 OCTETs.
In the community list, it could have some Well-known numbers such as:
BGP_COMMUNITY_ATTRIBUTE_NO_EXPORT 0xFFFFFF01
BGP_COMMUNITY_ATTRIBUTE_NO_ADVERTISE 0xFFFFFF02ro OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.18.1.1.9 |
snBgp4AttributeAsPathListTo show the AS Path list of this attribute entry.
A number from 1 to 0xFFFF.
This integer number is represented by 2 OCTETs.ro OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.18.1.1.10 |
snBgp4AttributeOriginatorThe originator IP address for an attribute entry.ro IpAddress .1.3.6.1.4.1.11.2.3.7.11.12.2.11.18.1.1.11 |
snBgp4AttributeClusterListTo show the cluster list of this attribute entry.
If the cluster list is an NULL string, it means an empty list.
Otherwise, the list is a group of cluster ID which is
represented by 4 OCTETs IP address.ro OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.18.1.1.12 |
snBgp4ClearNeighborCmd OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.19 |
snBgp4ClearNeighborCmdTableClear Bgp4 command table. SEQUENCE OF SnBgp4ClearNeighborCmdEntry .1.3.6.1.4.1.11.2.3.7.11.12.2.11.19.1 |
snBgp4ClearNeighborCmdEntryAn entry in the clear Bgp4 neighbor command table. SnBgp4ClearNeighborCmdEntry .1.3.6.1.4.1.11.2.3.7.11.12.2.11.19.1.1 |
snBgp4ClearNeighborCmdIpThe IP Address for a neighbor entry.
If the IP address is 255.255.255.255, it
means for all neighbors.ro IpAddress .1.3.6.1.4.1.11.2.3.7.11.12.2.11.19.1.1.1 |
snBgp4ClearNeighborCmdElementTo send the command element of this neighbor for value(1) to (5)
valid(0) is received in SNMP-get.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.19.1.1.2 |
snBgp4NeighPrefixGroup OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.2.11.20 |
snBgp4NeighPrefixGroupTableBgp4 Neighbor Prefix Group table. SEQUENCE OF SnBgp4NeighPrefixGroupEntry .1.3.6.1.4.1.11.2.3.7.11.12.2.11.20.1 |
snBgp4NeighPrefixGroupEntryAn entry in the Bgp4 Prefix Group table. SnBgp4NeighPrefixGroupEntry .1.3.6.1.4.1.11.2.3.7.11.12.2.11.20.1.1 |
snBgp4NeighPrefixGroupNeighIpThe IP Address for a neighbor entry.ro IpAddress .1.3.6.1.4.1.11.2.3.7.11.12.2.11.20.1.1.1 |
snBgp4NeighPrefixGroupDirThe incoming/outgoing advertisements to which
the access list is applied.ro Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.20.1.1.2 |
snBgp4NeighPrefixGroupInAccessListAn in access prefix list name.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.20.1.1.3 |
snBgp4NeighPrefixGroupOutAccessListAn out prefix list name.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.2.11.20.1.1.4 |
snBgp4NeighPrefixGroupRowStatusThis object is used to create and
delete row in the table and control
if they are used. The values
that can be written are:
delete(3)...deletes the row
create(4)...creates a new row
modify(5)...modifies an exsisting row
If the row exists, then a SET with
value of create(4) returns error
'badValue'. Deleted rows go away
immediately. The following values
can be returned on reads:
noSuch(0)...no such row
invalid(1)...Setting it to 'invalid' has the effect of
rendering it inoperative..
valid(2)....the row exists and is validrw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.2.11.20.1.1.5 |