HP-SN-AGENT-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for HP-SN-AGENT-MIB.
202
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
202 total| Object Name |
|---|
snChasGen OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.1.1 |
RFC1155-SMI Unknown .1.3.6.1.4.1.11.2.3.7.11.12.1.1.1 |
snChasTypeThe chassis type represents the type
of Foundry product being managed.ro DisplayString .1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.1 |
snChasSerNumThe serial number of the chassis. If the
serial number is unknown or unavailable then
the value should be a zero length string.ro DisplayString .1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.2 |
snChasPwrSupplyStatusA bit array that contains the value of the
Chassis Power Supplies. This is a packed bit string;
the 2 power supplies status are encoded into 4 bits
(a nibble).
There are multiple power supplies per chassis in this release.
The following shows the meaning of each bit:
(bit 0 is the least significant bit).
bit position meaning
12-31 reserved
11 Power Supply 4 DC (0=bad, 1=good).
10 Power Supply 3 DC (0=bad, 1=good).
9 Power Supply 4 present status (0=present, 1=not-present).
8 Power Supply 3 present status (0=present, 1=not-present).
4-7 reserved
3 Power Supply 2 DC (0=bad, 1=good).
2 Power Supply 1 DC (0=bad, 1=good).
1 Power Supply 2 present status (0=present, 1=not-present).
0 Power Supply 1 present status (0=present, 1=not-present).ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.3 |
snChasFanStatusA bit array that contains the value of the
fan status. This is a packed bit string. The
status of each fan is encoded into one bit.
bit value meaning
-
0 fan failure.
1 fan good.
There are two fans per VLAN Switch chassis in this release.
The following shows the meaning of each bit:
(bit 0 is the least significant bit).
bit position meaning
4-31 reserved
3 fan4 status
2 fan3 status
1 fan2 status
0 fan1 statusro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.4 |
snChasMainBrdDescriptionThe main board description string. (It is obsoleted for Chassis Product)ro DisplayString .1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.5 |
snChasMainPortTotalThe total number of ports for the main board. (It is obsoleted for Chassis Product)ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.6 |
snChasExpBrdDescriptionThe expansion board description string. Expansion
board are those boards attaching on the main board.
(It is obsoleted for Chassis Product)ro DisplayString .1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.7 |
snChasExpPortTotalThe total number of ports for the expansion board.
(It is obsoleted for Chassis Product)ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.8 |
snChasStatusLedsA bit array that contains the value of the
front panel status LEDs. This is a bit-map;
each LED is encoded into 1 bit for each switch
port. The maximum number of ports in one chassis
is 24 that means 24 Ports Status LEDs. The expansion port
number always begins from the last main port number.
The following shows the meaning of each bit for each
switch port:
bit value meaning
-
0 off (Link off)
1 on (Link on)
The bitmap of LEDs are as following:
(Port1) (Port4) (Port8)
Bit (Bit0) (Bit3) (Bit7)
Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8
Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16
Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.9 |
snChasTrafficLedsA bit array that contains the value of the
front panel traffic LEDs. This is a packed bit string;
each LED is encoded into 1 bit for each switch
port. The maximum number of ports in one chassis
is 24 that means 24 Ports Traffic LEDs. The expansion port
number always begins from the last main port number.
The following shows the meaning of each bit for each
switch port:
bit value meaning
-
0 off (no traffic)
1 on (traffic)
The bitmap of LEDs are as following:
(Port1) (Port4) (Port8)
Bit (Bit0) (Bit3) (Bit7)
Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8
Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16
Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.10 |
snChasMediaLedsA bit array that contains the value of the
front panel media LEDs. This is a packed bit string;
each LED is encoded into 1 bit for each switch port.
The maximum number of ports in one chassis is 24
that means 24 Ports Media LEDs. The expansion port
number always begins from the last main port number.
The following shows the meaning of each bit for each
switch port:
bit value meaning
-
0 half duplex
1 full duplex
The bitmap of LEDs are as following:
(Port1) (Port4) (Port8)
Bit (Bit0) (Bit3) (Bit7)
Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8
Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16
Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24
-ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.11 |
snChasEnablePwrSupplyTrapIndicates whether the SNMP agent process is
permitted to generate power supply failure traps.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.12 |
snChasMainBrdIdThe main board identifier, which can uniquely identify a board
type. It is an encoded octet string with the following meaning:
octet 0 - octet string format version, which identifies the
format of this string.
If format version octet has the value 1, the octets after the
version octet have the following meaning:
octet 1 - product type, FIWG=0x57, FIBB=0x42, FIMLS=0x4D
NI=0x4E, TI=0x54, TIRT=0x52
octet 2 - board type, POWERPC=1, ALPHA=2
The length of the octet string is 27.
If format version octet has the value 2, the octets after the
version octet have the following meaning:
octet 1 - product type:
BI_WG 0x57
BI_BB 0x42
BI_NI 0x4E
octet 2 - module type:
FI_MASTER_FIBER_8G 0x7
FI_MASTER_FIBER_4G 0x5
FI_MASTER_FIBER_2G 0x4
FI_SLAVE_COPPER_24 0xB
MASTER_FIBER_8G 0x0
MASTER_FIBER_4G 0x1
MASTER_FIBER_2G 0x12
MASTER_FIBER_0G 0x14
MASTER_COPPER_16 0x2
MASTER_COPPER_8G 0x6
MASTER_COPPER_12_2 0x9
SLAVE_FIBER_8G 0x8
SLAVE_FIBER_4G 0x3
SLAVE_COPPER_20 0xA
SLAVE_COPPER_24 0xA
SLAVE_100FX_8 0xD
SLAVE_100FX_16 0xC
SLAVE_COPPER_8G 0xE
SLAVE_COPPER_16_2 0xF
STACK_FIBER_8G 0x10
STACK_COPPER_8G 0x11
SLAVE_100FX_24 0x13
The length of the octet string is 28.
Both format version 1 and 2:
octet 3 - processor type, PVR_M603=3, PVR_M604=4, PVR_M603E=6,
PVR_M603EV=7, PVR_M604E=9
octet 4 to
octet 5 - processor speed in MHz
octet 6 - MAC type:
MAC_SEEQ_10_100=1,
MAC_DEC_10_100=2,
MAC_SEEQ_1000=5,
MAC_GMAC_1000=6,
MAC_VLSI_1000=9
octet 7 - PHY type, PHY_NONE=0, PHY_QSI=1, PHY_ICS=3,
PHY_NATIONAL=4, PHY_LEVEL1=6, PHY_LEVEL16=7,
PHY_LEVEL24=8
octet 8 - port type, COPPER=0, FIBER=1
octet 9 - fiber port type, NONFIBER=0, SX_FIBER=1,
LX_FIBER=2, LHX_FIBER=3, LX_SX_FIBER=4,
LHB_FIBER=5
octet 10 to
octet 13 - DRAM size in KBytes
octet 14 to
octet 17 - boot flash size in KBytes
octet 18 to
octet 21 - code flash size in KBytes
octet 22 to
octet 27 - serial number.
Format version 1 only:
octet 28 - chassis backplane type.
chassis4000 = 0x00
chassis8000 = 0x04
Turbo8 = 0x07 (stack2)
FastIron2 = 0x06 (stack1)ro OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.13 |
snChasExpBrdIdThe expansion board identifier. Expansion board are those
boards attaching on the main board. It is an encoded octet
string with the following meaning:
octet 0 - octet string format version, which identifies
the format of this string.
If format version octet has the value 1, the octets after
the version octet have the following meaning:
octet 1 - expansion board type, HUNDRED_MEG_1PORT=1,
HUNDRED_MEG_2PORT=2, HUNDRED_MEG_1PORT_COPPER=3,
HUNDRED_MEG_2PORT_COPPER=4, HUNDRED_MEG_2PORT_LX=5,
GIGA_1PORT=8, GIGA_2PORT=9
octet 2 - fiber port type, NONFIBER=0, SX_FIBER=1,
LX_FIBER=2, LHX_FIBER=3, LX_SX_FIBER=4
(It is obsoleted for Chassis Product)ro OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.14 |
snChasSpeedLedsA bit array that contains the value of the
front panel media LEDs. This is a packed bit string;
each LED is encoded into 1 bit for each switch port.
The maximum number of ports in one chassis is 24
that means 24 Ports Speed LEDs. The expansion port
number always begins from the last main port number.
The following shows the meaning of each bit for each
switch port:
bit value meaning
-
0 10 MBit
1 100 MBit
The bitmap of LEDs are as following:
(Port1) (Port4) (Port8)
Bit (Bit0) (Bit3) (Bit7)
Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8
Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16
Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24
-ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.15 |
snChasEnableFanTrapIndicates whether the SNMP agent process is
permitted to generate fan failure traps.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.16 |
snChasIdNumberAn administratively-assigned chassis identity number,
used by inventory control.rw DisplayString .1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.17 |
snChasActualTemperatureTemperature of the chassis. Each unit is 0.5 degrees Celcius.
Only management module built with temperature sensor hardware
is applicable. For those non-applicable management module, it
returns no-such-name.ro INTEGER (-110..250) .1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.18 |
snChasWarningTemperatureActual temperature higher than this threshold value will trigger
the switch to send a temperature warning trap. Each unit is 0.5
degrees Celcius. Only management module built with temperature
sensor hardware is applicable. For those non-applicable management
module, it returns no-such-name.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.19 |
snChasShutdownTemperatureActual temperature higher than this threshold value will shutdown
a partial of the switch hardware to cool down the system. Each unit
is 0.5 degrees Celcius. Only management module built with temperature
sensor hardware is applicable. For those non-applicable management
module, it returns no-such-name.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.20 |
snChasEnableTempWarnTrapIndicates whether the SNMP agent process is
permitted to generate temperature warning traps.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.21 |
snChasPwr OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.1.2 |
snChasPwrSupplyTableA table of each power supply information. Only installed
power supply appears in a table row. SEQUENCE OF SnChasPwrSupplyEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.1.2.1 |
snChasPwrSupplyEntryA row in the power supply table. SnChasPwrSupplyEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.1.2.1.1 |
snChasPwrSupplyIndexThe index to power supply table.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.1.2.1.1.1 |
snChasPwrSupplyDescriptionThe power supply description string.ro DisplayString .1.3.6.1.4.1.11.2.3.7.11.12.1.1.2.1.1.2 |
snChasPwrSupplyOperStatusThe power supply operation status.ro Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.1.2.1.1.3 |
snChasFan OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.1.3 |
snChasFanTableA table of each fan information. Only installed
fan appears in a table row. SEQUENCE OF SnChasFanEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.1.3.1 |
snChasFanEntryA row in the fan table. SnChasFanEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.1.3.1.1 |
snChasFanIndexThe index to fan table.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.1.3.1.1.1 |
snChasFanDescriptionThe fan description string.ro DisplayString .1.3.6.1.4.1.11.2.3.7.11.12.1.1.3.1.1.2 |
snChasFanOperStatusThe fan operation status.ro Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.1.3.1.1.3 |
snAgentGbl OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1 |
snAgReloadAction object to reboot the agent.
The following values can only be read:
other(1).....agent in unknown or other state
running(2)...agent running
The following value can be written:
reset(3).....do a hard reset
The agent will return a
response before the action occurs.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.1 |
snAgEraseNVRAMAction object to erase NVRAM of the agent.
The following values can only be read:
normal(1)
error(2)... operation failed or bad flash
erasing(4)...agent is erasing NVRAM flash
The following value can be written:
erase(3).....do erase
The agent will return a response even before the erase is done.
And the read value will be erasing until erase is done.
And the erase request will be rejected until error or normal.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.2 |
snAgWriteNVRAMAction object to save all configuration info to
NVRAM of the agent.
The following values can only be read:
normal(1)
error(2)... operation failed or bad flash
writing(4)...agent is writing NVRAM flash
The following value can be written:
write(3).....do write
The agent will return a response even before the write is done.
And the read value will be writing until write is done.
And the write request will be rejected until error or normal.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.3 |
snAgConfigFromNVRAMAction object to config the switch from NVRAM of the agent.
The following values can only be read:
normal(1)
error(2)... operation failed or bad flash
configing(4)...configing from NVRAM flash is in process.
The following value can be written:
config(3).....do config
The agent will return a response after config is done. Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.4 |
snAgTftpServerIpThe tftp server address, this will be used for both download/upload
image file and config file.rw IpAddress .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.5 |
snAgImgFnameName of the image file including path currently associated
with the system. When the object is not used, the value is a
zero length string.rw DisplayString .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.6 |
snAgImgLoadAction object to down/up load a new image
to the agent. The following values:
Error values: from normal(1) to operationError(17) and tftpWrongFileType(23).
loading(18) .. operation is in process.
The following values are used for set :
uploadPrimary(19)..upload the Primary image from flash to tftp server.
downloadPrimary(20)..download the Primary image from tftp server to flash.
uploadSecondary(21)..upload the Secondary image from flash to tftp server.
downloadSecondary(22)..download the Secondary image from tftp server to flash.
The image filename is defined in
snAgImgFname. The tftp server address is defined in snAgTftpServerIp.
Atomic set of snAgImgLoad, snAgImgFname and
snAgTftpServerIp is required to allow down/up load to happen.
And the write request will be rejected during loading until error
or normal.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.7 |
snAgCfgFnameName of the config file(s) including path currently associated
with the system. Some agents in special
situations may support a value which contains
multiple file names instead of a single file
name. Multiple names are specified as a list
of file names separated by semicolons (;).
When the object is not used, the value is a
zero length string.rw DisplayString .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.8 |
snAgCfgLoadAction object to down/up load a config image
to the agent. The following values can be
read :
Error values: from normal(1) to operationError(17) and tftpWrongFileType(29).
loading(18) .. operation is in process.
The following value can be used to set:
uploadFromFlashToServer(20)..upload the config from flash
to tftp server.
downloadToFlashFromServer(21)..download the config to flash
from tftp server.
uploadFromDramToServer(22)..upload the config from DRAM
to tftp server.
downloadToDramFromServer(23)..download the config to DRAM
from tftp server.
The following value can be used to set:
uploadFromFlashToNMS(24)..upload the config from flash to NMS.
downloadToFlashFromNMS(25)..download the config to flash from NMS.
uploadFromDramToNMS(26)..upload the config from DRAM to NMS.
downloadToDramFromNMS(27)..download the config to DRAM from NMS.
The config filename is defined in
snAgCfgFname. The tftp server address is defined in snAgTftpServerIp.
Atomic set of snAgCfgLoad, snAgCfgFname and snAgTftpServerIp is
required to allow down/up load to happen. And the write request
will be rejected during loading until error or normal.
For those NMS commands from (24) to (27), The snAgCfgEosTable MIB must
be sent along in one PDU. A seperate write memory cli or set
snAgWriteNVRAM is required to save the config to NVRAM.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.9 |
snAgDefGwayIpThe default gateway (router) address.rw IpAddress .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.10 |
snAgImgVerThe version of the running software in the form
'major.minor.maintenance[letters]'.ro DisplayString .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.11 |
snAgFlashImgVerThe version of the software image saved in local
storage such as flash memory in the form
'major.minor.maintenance[letters]'. If not
known or not available, then the value is
a zero length string.ro DisplayString .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.12 |
snAgGblIfIpAddrThe interface ip address.rw IpAddress .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.13 |
snAgGblIfIpMaskThe interface ip address mask.rw IpAddress .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.14 |
snAgGblPasswordSystem Security Access Password and this is only
allowed to use for setting but not for reading.
An SNMP-Get will get an zero string.rw DisplayString .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.15 |
snAgTrpRcvrCurEntryThe current total entries of the Trap
Receiver Table are created.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.16 |
snAgGblDataRetrieveModeBy default, this mode is set to nextbootCfg(0).
The VLAN Table and Port-STP Table data will be retrieved
according to this mode.
nextbootCfg(0).........the nextboot configuration data are retrieved
operationalData(1)..........the current running data are retrievedrw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.19 |
snAgSystemLogThe system log object to indicate whether any Network
Management Station(NMS) has login. The first byte
of the octet string is the value decribed below and
followed by 4 bytes of secret code.
login(1)..... a value for a NMS to login.
heartbeat(2)... a value for the login NMS periodically to
checkin; Otherwise, the Agent will automatically
set this object to logout(3) after a timeout
period.
logout(3).... a value for a NMS to logout.
changePassword(4).... a value for the login NMS to change
password, only if snAgGblPasswordChangeMode
was configured to 'anyMgmtEntity'.
changeReadOnlyCommunity(5).... a value for the login NMS
to change the read-only community string,
only if snAgGblPasswordChangeMode was
configured to 'anyMgmtEntity'.
changeReadWriteCommunity(6).... a value for the login NMS
to change the read-write community string,
only if snAgGblPasswordChangeMode was
configured to 'anyMgmtEntity'.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.20 |
snAgGblEnableColdStartTrapIndicates whether the SNMP agent process is
permitted to generate cold start traps.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.21 |
snAgGblEnableLinkUpTrapIndicates whether the SNMP agent process is
permitted to generate link up traps.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.22 |
snAgGblEnableLinkDownTrapIndicates whether the SNMP agent process is
permitted to generate link down traps.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.23 |
snAgGblPasswordChangeModeSpecify which management entity is allowed to change
the password. 'anyMgmtEntity' management entities are
SNMP management station, console command line interface,
and telnet command line interface. For security reason,
this object can only be modified by console command line
interface or telnet command line interface. The default
value is 'consoleAndTelnet', of which both console and
telnet command line interfaces are allowed to change
the password.ro Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.24 |
snAgGblReadOnlyCommunitySNMP read community string and this is only allowed
to use for setting but not for reading. An SNMP-Get
will get an zero length string.rw DisplayString .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.25 |
snAgGblReadWriteCommunitySNMP read-write community string and this is only
allowed to use for setting but not for reading. An
SNMP-Get will get an zero length string.rw DisplayString .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.26 |
snAgGblCurrentSecurityLevelThis represnts the current log-in security level.
Each level of security requires a password to permit
user for different system configurations.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.27 |
snAgGblSecurityLevelSetThis shows which the security level password to be set.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.28 |
snAgGblLevelPasswordsMaskThis shows the bitmap of level passwords which successfully assigned to the system.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.29 |
snAgGblQueueOverflowfalse - The device queues are not overflow.
true - The device queues are overflow.ro Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.30 |
snAgGblBufferShortagefalse - The device buffers are adequate.
true - The device buffers are in shortage.ro Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.31 |
snAgGblDmaFailurefalse - The device DMAs are in good condition.
true - One of the DMAs in the device fails.ro Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.32 |
snAgGblResourceLowWarningfalse - No, the device does not have resource-low-warning.
true - Yes, the device does have resource-low-warning.ro Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.33 |
snAgGblExcessiveErrorWarningfalse - No, the device does not have any excessive collision, FCS errors, alignment warning etc.
true - Yes, the device does have.ro Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.34 |
snAgGblCpuUtilDataThe statistics collection of utilization of the CPU in the device.ro Gauge .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.35 |
snAgGblCpuUtilCollectenable(1) - The beginning of statistics collection of utilization of the CPU in the device.
disable(0) - The end of statistics collection of utilization of the CPU in the device.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.36 |
snAgGblTelnetTimeoutTelnet session idling timeout value. Writing value 0 to
this object never timeouts any telnet sessions. Each value
unit is one minute.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.37 |
snAgGblEnableWebMgmtEnable/disable web management.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.38 |
snAgGblSecurityLevelBindingThis represnts the binding of a given password to which
security level. A value of 255 indicates an invalid
binding.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.39 |
snAgGblEnableSLBEnable/disable Server Load Balancing.ro Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.40 |
snAgSoftwareFeatureA bit string representing the software feature of the running
switch/router image. These features were conditional compiled
to different product images. For each bit, exist feature has
a value of 1, but non-exist feature has a value of 0.
octet 0, bit 0 - RMON
octet 0, bit 1 - ipx switching
octet 0, bit 2 - server load balancing
octet 0, bit 3 - layer 3 filter in switch
octet 0, bit 4 - ipx routing
octet 0, bit 5 - appletalk routing
octet 0, bit 6 - ip multicast routing
octet 0, bit 7 - local access control
octet 1, bit 0 - BGP routing
octet 1, bit 1 - loopback interface
octet 1, bit 2 - BigIron multi-management module
octet 1, bit 3 - BigIron SYSIF II
octet 1, bit 4 - BigIron POS support
octet 1, bit 5 - appletalk cable vlan
octet 1, bit 6 - 64 subnet
octet 1, bit 7 - multi-slot trunk
octet 2, bit 0 - TACACS
octet 2, bit 1 - Gigabit Ethernet port auto-negotiation mode
octet 2, bit 2 - FSRP
octet 2, bit 3 - Exodus requested OSPF enhancement
octet 2, bit 4 - OSPF NSSA
octet 2, bit 5 - POS
octet 2, bit 6 - QOS
octet 2, bit 7 - Single Span
octet 3, bit 0 - Fast Span
octet 3, bit 1 - Base L3
octet 3, bit 2 - static log buffer
Bit 0 is the least significant bit of an octet, and
bit 7 is the most significant bit of an octet.ro OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.41 |
snAgGblEnableModuleInsertedTrapIndicates whether the SNMP agent process is permitted to
generate hardware module inserted to chassis traps.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.42 |
snAgGblEnableModuleRemovedTrapIndicates whether the SNMP agent process is permitted to
generate hardware module removed from chassis traps.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.43 |
snAgGblTrapMessageA generic trap message string.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.44 |
snAgGblEnableTelnetServerEnable or disable telnet server in device.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.45 |
snAgGblTelnetPasswordTelnet Access Password and this is only
allowed to use for setting but not for reading.
An SNMP-Get will get an zero string.rw DisplayString .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.46 |
snAgBuildDateThe date of the built software.ro DisplayString .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.47 |
snAgBuildtimeThe time of the built software.ro DisplayString .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.48 |
snAgBuildVerThe version of the built software in the form
'major.minor.maintenance[letters]'.ro DisplayString .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.49 |
snAgentBrd OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.2 |
snAgentBrdTableA table of each physical board information. SEQUENCE OF SnAgentBrdEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1 |
snAgentBrdEntryA row in the Agent Board table. SnAgentBrdEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1 |
snAgentBrdIndexThe index to the Agent Interface Table.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.1 |
snAgentBrdMainBrdDescriptionThe main board description string.ro DisplayString .1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.2 |
snAgentBrdMainBrdIdThe main board identifier, which can uniquely identify a board
type. It is an encoded octet string with the following meaning:
octet 0 - octet string format version, which identifies the
format of this string.
If format version octet has the value 2, the octets after the
version octet have the following meaning:
octet 1 - product type:
BI_WG 0x57
BI_BB 0x42
BI_NI 0x4E
octet 2 - module type:
MASTER_FIBER_8G 0x0
MASTER_FIBER_4G 0x1
MASTER_FIBER_2G 0x12
MASTER_FIBER_0G 0x14
MASTER_COPPER_16 0x2
MASTER_COPPER_8G 0x6
MASTER_COPPER_12_2 0x9
SLAVE_FIBER_8G 0x8
SLAVE_FIBER_4G 0x3
SLAVE_FIBER_2G 0x17
SLAVE_COPPER_8G 0xE
SLAVE_COPPER_2G 0x18
SLAVE_COPPER_16_2 0xF
SLAVE_COPPER_20 0xA
SLAVE_COPPER_24 0xA
SLAVE_100FX_8 0xD
SLAVE_100FX_16 0xC
SLAVE_100FX_24 0x13
STACK_FIBER_8G 0x10
STACK_COPPER_8G 0x11
POS_622M 0x15
POS_155M 0x16
octet 3 - processor type, PVR_M603=3, PVR_M604=4, PVR_M603E=6,
PVR_M603EV=7, PVR_M604E=9
octet 4 to
octet 5 - processor speed in MHz
octet 6 - MAC type:
MAC_SEEQ_10_100=1,
MAC_DEC_10_100=2,
MAC_SEEQ_1000=5,
MAC_GMAC_1000=6,
MAC_VLSI_1000=9
octet 7 - PHY type, PHY_NONE=0, PHY_QSI=1, PHY_ICS=3,
PHY_NATIONAL=4, PHY_LEVEL1=6, PHY_LEVEL16=7,
PHY_LEVEL24=8
octet 8 - port type, COPPER=0, FIBER=1
octet 9 - fiber port type, NONFIBER=0, SX_FIBER=1,
LX_FIBER=2, LHX_FIBER=3
octet 10 to
octet 13 - DRAM size in KBytes
octet 14 to
octet 17 - boot flash size in KBytes
octet 18 to
octet 21 - code flash size in KBytes
octet 22 to
octet 27 - serial number.
octet 28 - chassis backplane type.
chassis4000 = 0x00
chassis8000 = 0x04
Turbo8 = 0x07 (stack2)
FastIron2 = 0x06 (stack1)ro OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.3 |
snAgentBrdMainPortTotalThe total number of ports for the main board.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.4 |
snAgentBrdExpBrdDescriptionThe expansion board description string. Expansion
board are those boards attaching on the main board.ro DisplayString .1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.5 |
snAgentBrdExpBrdIdThe expansion board identifier. Expansion board are those
boards attaching on the main board. It is an encoded octet
string with the following meaning:
octet 0 - octet string format version, which identifies
the format of this string.
If format version octet has the value 1, the octets after
the version octet have the following meaning:
octet 1 - expansion board type, HUNDRED_MEG_1PORT=1,
HUNDRED_MEG_2PORT=2, HUNDRED_MEG_1PORT_COPPER=3,
HUNDRED_MEG_2PORT_COPPER=4, HUNDRED_MEG_2PORT_LX=5,
GIGA_1PORT=8, GIGA_2PORT=9
octet 2 - fiber port type, NONFIBER=0, SX_FIBER=1,
LX_FIBER=2, LHX_FIBER=3, LX_SX_FIBER=4ro OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.6 |
snAgentBrdExpPortTotalThe total number of ports for the expansion board.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.7 |
snAgentBrdStatusLedsA bit array that contains the value of the
front panel status LEDs. This is a bit-map;
each LED is encoded into 1 bit for each switch
port. The maximum number of ports in one chassis
is 32 that means 32 Ports Status LEDs. The expansion port
number always begins from the last main port number.
The following shows the meaning of each bit for each
switch port:
bit value meaning
-
0 off (Link off)
1 on (Link on)
The bitmap of LEDs are as following:
(Port1) (Port4) (Port8)
Bit (Bit0) (Bit3) (Bit7)
Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8
Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16
Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.8 |
snAgentBrdTrafficLedsA bit array that contains the value of the
front panel traffic LEDs. This is a packed bit string;
each LED is encoded into 1 bit for each switch
port. The maximum number of ports in one chassis
is 24 that means 24 Ports Traffic LEDs. The expansion port
number always begins from the last main port number.
The following shows the meaning of each bit for each
switch port:
bit value meaning
-
0 off (no traffic)
1 on (traffic)
The bitmap of LEDs are as following:
(Port1) (Port4) (Port8)
Bit (Bit0) (Bit3) (Bit7)
Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8
Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16
Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.9 |
snAgentBrdMediaLedsA bit array that contains the value of the
front panel media LEDs. This is a packed bit string;
each LED is encoded into 1 bit for each switch port.
The maximum number of ports in one chassis is 24
that means 24 Ports Media LEDs. The expansion port
number always begins from the last main port number.
The following shows the meaning of each bit for each
switch port:
bit value meaning
-
0 half duplex
1 full duplex
The bitmap of LEDs are as following:
(Port1) (Port4) (Port8)
Bit (Bit0) (Bit3) (Bit7)
Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8
Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16
Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24
-ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.10 |
snAgentBrdSpeedLedsA bit array that contains the value of the
front panel media LEDs. This is a packed bit string;
each LED is encoded into 1 bit for each switch port.
The maximum number of ports in one chassis is 24
that means 24 Ports Speed LEDs. The expansion port
number always begins from the last main port number.
The following shows the meaning of each bit for each
switch port:
bit value meaning
-
0 10 MBit
1 100 MBit
The bitmap of LEDs are as following:
(Port1) (Port4) (Port8)
Bit (Bit0) (Bit3) (Bit7)
Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8
Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16
Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24
-ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.11 |
snAgentBrdModuleStatusBy default, this mode is set to notActivated(0).
moduleEmpty(0) ......... The slot of the chassis is empty.
moduleGoingDown(2) ..... The module is going down.
moduleRejected(3) ...... The module is being rejected due to wrong configuration.
moduleBad(4) ........... The module Hardware is bad.
moduleComingUp(9) ...... The module is in power-up cycle.
moduleRunning(10) ....... The module is running.ro Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.12 |
snAgentBrdRedundantStatusThe redundant status of a module. Non-management module always
returns other(1). Management module returns the rest of the
states.ro Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.13 |
snAgentBrdAlarmLedsA bit array that contains the value of the
front panel media LEDs (for POS Module Only). This is a packed bit string;
each LED is encoded into 1 bit for each switch port.
The maximum number of ports in one chassis is 24
that means 24 Ports Speed LEDs. The expansion port
number always begins from the last main port number.
The following shows the meaning of each bit for each
switch port:
bit value meaning
-
0 no alarm
1 alarm
The bitmap of LEDs are as following:
(Port1) (Port4) (Port8)
Bit (Bit0) (Bit3) (Bit7)
Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8
Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16
Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24
-ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.14 |
snAgentBrdTxTrafficLedsA bit array that contains the value of the
front panel transmit traffic LEDs (for POS Module Only). This is a packed bit string;
each LED is encoded into 1 bit for each switch
port. The maximum number of ports in one chassis
is 24 that means 24 Ports Transmit Traffic LEDs. The expansion port
number always begins from the last main port number.
The following shows the meaning of each bit for each
switch port:
bit value meaning
-
0 off (no transmit traffic)
1 on (transmit traffic)
The bitmap of LEDs are as following:
(Port1) (Port4) (Port8)
Bit (Bit0) (Bit3) (Bit7)
Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8
Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16
Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.15 |
snAgentBrdRxTrafficLedsA bit array that contains the value of the
front panel receive traffic LEDs (for POS Module Only). This is a packed bit string;
each LED is encoded into 1 bit for each switch
port. The maximum number of ports in one chassis
is 24 that means 24 Ports Receive Traffic LEDs. The expansion port
number always begins from the last main port number.
The following shows the meaning of each bit for each
switch port:
bit value meaning
-
0 off (no receive traffic)
1 on (receive traffic)
The bitmap of LEDs are as following:
(Port1) (Port4) (Port8)
Bit (Bit0) (Bit3) (Bit7)
Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8
Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16
Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.16 |
snAgentTrp OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.3 |
snAgTrpRcvrTableA table of managers which to send traps. SEQUENCE OF SnAgTrpRcvrEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.2.3.1 |
snAgTrpRcvrEntryA row in the trap receiver table.
The column snAgTrpRcvrStatus is used to create
and delete rows in the table. Creation requires
a SET PDU with objects snAgTrpRcvrIndex,
snAgTrpRcvrIpAddr, snAgTrpRcvrComm and
snAgTrpRcvrStatus. SnAgTrpRcvrEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.2.3.1.1 |
snAgTrpRcvrIndexThe index to the Trap Receiver Table.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.3.1.1.1 |
snAgTrpRcvrIpAddrThe ip address for
SNMP manager that is to receive the trap.rw IpAddress .1.3.6.1.4.1.11.2.3.7.11.12.1.2.3.1.1.2 |
snAgTrpRcvrCommCommunity string to use.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.1.2.3.1.1.3 |
snAgTrpRcvrStatusThis object is used to create and
delete rows in the table and control
if they are used. The values
that can be written are:
ignore(5)...don't use this entry to
send traps to at this time
delete(3)...deletes the row
create(4)...creates a new row
If the row exists, then a SET with
value of create(5) returns error
'badValue'. Deleted rows go away
immediately. The following values
can be returned on reads:
other(1)....some other case
valid(2)....the row exists and is valid
ignore(5)...don't use this entry to
send traps to at this timerw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.2.3.1.1.4 |
snAgentBoot OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.4 |
snAgBootSeqTableA table of image load sequnce instructions to the boot code.
Boot code will start from instruction of the first valid entry
to load the image. If failed, it will use the second valid
entry and so on, until a succesful load has completed. Each
entry must have an unique instruction, duplicate instructions
will be rejected. SEQUENCE OF SnAgBootSeqEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.2.4.1 |
snAgBootSeqEntryA row in the boot sequence table. SnAgBootSeqEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.2.4.1.1 |
snAgBootSeqIndexThe index to the boot sequence table.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.4.1.1.1 |
snAgBootSeqInstructionThe instruction for the boot code.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.2.4.1.1.2 |
snAgBootSeqIpAddrThe ip address of the TFTP server if snAgBootSeqInstruction
was set to 'fromTftpServer'; otherwise, this object is not
used in any other boot instruction.rw IpAddress .1.3.6.1.4.1.11.2.3.7.11.12.1.2.4.1.1.3 |
snAgBootSeqFilenameThe image filename on the TFTP server if snAgBootSeqInstruction
was set to 'fromTftpServer'; otherwise, this object is not
used in any other boot instruction.rw DisplayString .1.3.6.1.4.1.11.2.3.7.11.12.1.2.4.1.1.4 |
snAgBootSeqRowStatusTo create or delete a boot sequence table entry.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.2.4.1.1.5 |
snAgCfgEos OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.5 |
snAgCfgEosTableThis table represents the fragmented Configuration File data packet
with checksum include in each rows of this table. A SNMP-SET
represents configuration file download, and a SNMP-GET represents
configuration file upload. This action is only if the SNMP-SET of
snAgCfgLoad command is sent along with this table consecutively. The
applicable snAgCfgLoad command value is as followings:
uploadFromFlashToNMS(23),
downloadToFlashFromNMS(24),
uploadFromDramToNMS(25),
downloadToDramFromNMS(26). SEQUENCE OF SnAgCfgEosEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.2.5.1 |
snAgCfgEosEntryAn EOS row in the table of encoded octet strings for table
snAgCfgEosTable. SnAgCfgEosEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.2.5.1.1 |
snAgCfgEosIndexEach VLAN EOS Buffer Identifier have a multiple
VLAN table entries.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.5.1.1.1 |
snAgCfgEosPacketAn encoded octet string. On reads it contains an integral
number of configuration file data packets. The size
of each encoded octet string is less than or equal to 1400
bytes.rw OCTET STRING .1.3.6.1.4.1.11.2.3.7.11.12.1.2.5.1.1.2 |
snAgCfgEosChkSumA checksum of each configuration file data packet.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.5.1.1.3 |
snAgentLog OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.6 |
snAgSysLogGbl OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1 |
snAgSysLogGblEnableEnable/disable system logging.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1.1 |
snAgSysLogGblBufferSizeThe number of dynamic system logging entries.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1.2 |
snAgSysLogGblClearClear dynamic and/or static system logging buffers.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1.3 |
snAgSysLogGblCriticalLevelFilter events going to the logging buffer. This is a packed
bit string object of which each bit has the following meaning:
(bit 0 is the least significant bit).
bit position meaning
8-31 reserved
7 Warning (warning conditions)
6 Notification (normal but significant conditions)
5 Informational (informational messages)
4 Error (error conditions)
3 Emergency (system is unusable)
2 Debugging (debugging messages)
1 Critical (critical conditions)
0 Alert (immediate action needed)
Setting a critical level bit to 1 makes the logging buffer
accept the corresponding event. Resetting a critical level
bit to 0 makes the logging buffer reject the corresponding
event.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1.4 |
snAgSysLogGblLoggedCountThe number events logged in the system logging buffer.ro Counter .1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1.5 |
snAgSysLogGblDroppedCountThe number of events dropped.ro Counter .1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1.6 |
snAgSysLogGblFlushedCountThe number of times that the system logging buffer was cleared.ro Counter .1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1.7 |
snAgSysLogGblOverrunCountThe number of times that the system logging buffer was wrapped
around.ro Counter .1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1.8 |
snAgSysLogGblServerIP address of syslog server.rw IpAddress .1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1.9 |
snAgSysLogGblFacilityFacility code.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1.10 |
snAgSysLogBufferTableDynamic system logging buffer table. SEQUENCE OF SnAgSysLogBufferEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.2 |
snAgSysLogBufferEntryA row in the dynamic system logging buffer table. SnAgSysLogBufferEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.2.1 |
snAgSysLogBufferIndexThe index to the dynamic system logging buffer table.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.2.1.1 |
snAgSysLogBufferTimeStampA time stamp when the event is logged.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.2.1.2 |
snAgSysLogBufferCriticalLevelThe critical level of this event.ro Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.2.1.3 |
snAgSysLogBufferMessageThe system logging message.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.2.1.4 |
snAgSysLogBufferCalTimeStampA time stamp when the event is logged. This object returns
a NULL terminated time stamp string if the system calendar
time was set. It returns a zero length string if the system
calendar time was not set.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.2.1.5 |
snAgStaticSysLogBufferTableStatic system logging buffer table. SEQUENCE OF SnAgStaticSysLogBufferEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.3 |
snAgStaticSysLogBufferEntryA row in the static system logging buffer table. SnAgStaticSysLogBufferEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.3.1 |
snAgStaticSysLogBufferIndexThe index to the static system logging buffer table.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.3.1.1 |
snAgStaticSysLogBufferTimeStampA time stamp when the event is logged.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.3.1.2 |
snAgStaticSysLogBufferCriticalLevelThe critical level of this event.ro Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.3.1.3 |
snAgStaticSysLogBufferMessageThe system logging message.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.3.1.4 |
snAgStaticSysLogBufferCalTimeStampA time stamp when the event is logged. This object returns
a NULL terminated time stamp string if the system calendar
time was set. It returns a zero length string if the system
calendar time was not set.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.3.1.5 |
snAgentSysParaConfig OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.7 |
snAgentSysParaConfigTableA table of Agent of each board. SEQUENCE OF SnAgentSysParaConfigEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.2.7.1 |
snAgentSysParaConfigEntryA row in the Agent System Parameters Configuation table. SnAgentSysParaConfigEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.2.7.1.1 |
snAgentSysParaConfigIndexThe index to the Agent System Parameters Configuation Table.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.7.1.1.1 |
snAgentSysParaConfigDescriptionThe main board description string.ro DisplayString .1.3.6.1.4.1.11.2.3.7.11.12.1.2.7.1.1.2 |
snAgentSysParaConfigMinThe minimum value of this Agent System Parameter.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.7.1.1.3 |
snAgentSysParaConfigMaxThe maximum value of this Agent System Parameter.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.7.1.1.4 |
snAgentSysParaConfigDefaultThe default value of this Agent System Parameter.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.7.1.1.5 |
snAgentSysParaConfigCurrentThe current configurated value of this Agent System Parameter.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.7.1.1.6 |
snAgentConfigModule OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.8 |
snAgentConfigModuleTableA table of each configured module information. SEQUENCE OF SnAgentConfigModuleEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.2.8.1 |
snAgentConfigModuleEntryA row in the Agent Configured Module table. SnAgentConfigModuleEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.2.8.1.1 |
snAgentConfigModuleIndexThe index to the Agent Configured Module Table.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.8.1.1.1 |
snAgentConfigModuleTypeThe Configured Module Type.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.2.8.1.1.2 |
snAgentConfigModuleRowStatusTo create or delete a configured module table entry.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.2.8.1.1.3 |
snAgentUser OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.9 |
snAgentUserGbl OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.9.1 |
snAgentUserMaxAccntMaximum number of user account entries can be configured.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.9.1.1 |
snAgentUserAccntTableA table of user account information. SEQUENCE OF SnAgentUserAccntEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.2.9.2 |
snAgentUserAccntEntryA row in the Agent User table. SnAgentUserAccntEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.2.9.2.1 |
snAgentUserAccntNameThe user name.ro DisplayString .1.3.6.1.4.1.11.2.3.7.11.12.1.2.9.2.1.1 |
snAgentUserAccntPasswordThe user password.rw DisplayString .1.3.6.1.4.1.11.2.3.7.11.12.1.2.9.2.1.2 |
snAgentUserAccntEncryptCodeThe password encryption method code.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.9.2.1.3 |
snAgentUserAccntPrivilegeThe user privilege.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.9.2.1.4 |
snAgentUserAccntRowStatusTo create or delete a user account table entry.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.2.9.2.1.5 |
snAgentRedundant OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.10 |
snAgentRedunGbl OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.10.1 |
snAgentRedunActiveMgmtModSlot number of the active management module. Setting
this object does not take effect immediately. Saving
configuration data to flash storage and reboot the
system are required to take effect. Setting a value of 0
requests the system to auto-select an active management
module after power up.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.10.1.1 |
snAgentRedunSyncConfigFrequency of the backup management module copying the
configuration data from the active management module.
Each unit is 1 second. Setting a value 0 will disable
the synchronization copy. Setting a negative value will
initiate the synchronization copy once immediately.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.2.10.1.2 |
snAgentRedunBkupCopyBootCodeIf enabled(1), the backup management module copies the boot code
from the active management module to its boot code flash storage
after power up, and whenever the active management module's boot
code is updated. The backup management module does not copy if
both boot codes were identical.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.2.10.1.3 |
snAgentEnableMgmtModRedunStateChangeTrapIndicates whether the SNMP agent process is permitted to
generate management module redundancy state change traps.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.2.10.1.4 |
snAgentRedunBkupBootLoadAction object to down load a new boot code from boot flash storage
of the active management module to the backup management module.
The following are returned values from get operation:
normal(1)............no operation
operationError(17)...error codes
The following are input values from set operation:
downloadBackup(20)...download the boot code from the active
management module to the backup management
module
Any set operation is rejected during loading until error
or normal state is reached.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.2.10.1.5 |
snAgentRedunSwitchOverTo force a switch-over from standby to active state
if the backup management module exists in a chassis.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.2.10.1.6 |
snStackGen OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.5.1 |
snStackPriSwitchModeThe Stackable Management Primary Switch mode
either enabled or disabled and the default is
disabled mode.
enabled(1)...........primary switch enabled
disabled(0)..........primary switch disabledrw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.5.1.1 |
snStackMaxSecSwitchThe Maximum Secondary Switches are allowed in the
Stackable Management Group.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.5.1.2 |
snStackTotalSecSwitchThe Total Secondary Switches currently connected to the
Stackable Management Group.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.5.1.3 |
snStackSyncAllSecSwitchSynchronize all the secondary switches in the
Stackable Management Group with the following commands.
device(2)...........device related parameters.
global(3)...........global parameters.
local(4)............local parameters.
The return result of the above commands are either
normal(0)...........normal condition.
invalid(1)...........invalid result.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.5.1.4 |
snStackSmSlotIndexThe Slot 0 is the Master slot and Slot 1-8 are slaves.
All the slot-based MIB data can be retrieved with respect to
this slot index such as snChassis global MIB.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.5.1.5 |
snStackFmpSetProcessnormal(0) - The set process is either in an idle state or FMP-SET-SUCCESS state.
pending(1) - The pending process is waiting for the result of an FMP-SET.
failure(2) - The failure result of an FMP-SET.ro Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.5.1.6 |
snStackSecSwitchInfo OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.11.12.1.5.2 |
snStackSecSwitchTableIf snSwGroupOperMode is configured as basic mode
which is VLAN by Port, Layer2 switching,
then this table is valid. Each VLAN switch port
could have a number of VLAN IDs. SEQUENCE OF SnStackSecSwitchEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1 |
snStackSecSwitchEntryAn entry in the Stackable Management Secondary Switch
Information table. SnStackSecSwitchEntry .1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1 |
snStackSecSwitchIndexThe secondary switch index must not be greater than the snStackMaxSecSwitch.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1.1 |
snStackSecSwitchSlotIdThe secondary switch slot ID must be set before the Configuration
command sent from the primary switch to the secondary switch
either manually or automatically - snStackSecSwitchCfgCmd.rw INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1.2 |
snStackSecSwitchPortCntsThe number of ports in this secondary switch.ro INTEGER .1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1.3 |
snStackSecSwitchEnabledThe secondary switch has been selected to Stackable Management Group.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1.4 |
snStackSecSwitchAckThe secondary switch has sent reponse to the primary switch.ro Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1.5 |
snStackSecSwitchMacAddrThe secondary switch physical address. The physical address
represents a MAC Station.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1.6 |
snStackSecSwitchSyncCmdSynchronize the secondary switches in the
Stackable Management Group with the following commands.
device(2)...........device related parameters.
global(3)...........global parameters.
local(4)............local parameters.
The return result of the above commands are either
normal(0)...........normal condition.
invalid(1)...........invalid result.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1.7 |
snStackSecSwitchIpAddrThe secondary switch IP Address and is used for
manual-command of snStackSecSwitchCfgCmd.rw IpAddress .1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1.8 |
snStackSecSwitchSubnetMaskThe secondary switch IP Subnet Mask and is used for
manual-command of snStackSecSwitchCfgCmd.rw IpAddress .1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1.9 |
snStackSecSwitchCfgCmdsnStackSecSwitchSlotId must be set before the Configuration
command sent from the primary switch to the secondary switch
either manually or automatically.
auto(2)...........auto-configuration command sent.
manual(3).........manual-configuration command sent.
if manual-mode is used, snStackSecSwitchIpAddr
and snStackSecSwitchSubnetMask must be
first set before this command is sent.
The return result of the above commands are either
normal(0)...........normal condition.
invalid(1)..........invalid result.rw Enumeration .1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1.10 |