HP-ICF-RATE-LIMIT-MIB
AI MIB Summary
The HP-ICF-RATE-LIMIT-MIB enables monitoring of traffic policing and shaping configurations on HP Intelligent Call Flow (ICF) network devices, specifically tracking applied rate limit thresholds, current throughput statistics, and dropped packet counters for bandwidth management enforcement.
This MIB module describes HP rate limit information.
Main OID:
hpicfRateLimitMIB.1.3.6.1.4.1.11.2.14.10.2.14
101
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
101 total| Object Name |
|---|
hpicfRateLimitMIBThis MIB module describes HP rate limit information. MODULE-IDENTITY .1.3.6.1.4.1.11.2.14.10.2.14 |
hpicfRateLimitObjects OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.10.2.14.1 |
hpicfICMPRateLimitObjects OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.10.2.14.1.1 |
hpICMPRateLimitConfig OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.10.2.14.1.1.1 |
hpICMPRateLimitPortConfigTableA table that contains configuration objects on ICMP rate limit on a per interface basis. SEQUENCE OF HpICMPRateLimitPortConfigEntry .1.3.6.1.4.1.11.2.14.10.2.14.1.1.1.1 |
hpICMPRateLimitPortConfigEntryEntry that contains configuration objects on ICMP rate limit on a per interface basis HpICMPRateLimitPortConfigEntry .1.3.6.1.4.1.11.2.14.10.2.14.1.1.1.1.1 |
hpICMPRateLimitPortConfigIndexThe interface index associated with this entry. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.11.2.14.10.2.14.1.1.1.1.1.1 |
hpICMPRateLimitPortStateThis object indicates whether ICMP rate limiting is enabled on the corresponding port. Because this is a State object it cannot distinguish between percent-based ICMP Rate-Limiting and the newer Kbps-based ICMP Rate-Limiting. Therefore, it has been deprecated in favor of hpICMPRateLimitPortControlMode.rwdeprecated Enumeration .1.3.6.1.4.1.11.2.14.10.2.14.1.1.1.1.1.2 |
hpICMPRateLimitPortPrctThis indicates the percent of ICMP rate limit on the port. The value of this object must be interpreted under the context of hpICMPRateLimitPortState. A value of 0 is not the same as disabling, but rather all ICMP traffic must be dropped.rw Integer32 .1.3.6.1.4.1.11.2.14.10.2.14.1.1.1.1.1.3 |
hpICMPRateLimitPortAlarmFlagThis object indicates whether ICMP rate limiting alarm has been sent. When an alarm is sent, this object is set to set(2). Once a management station changes this object to clear(1), an alarm can be sent again for this port.rw Enumeration .1.3.6.1.4.1.11.2.14.10.2.14.1.1.1.1.1.4 |
hpICMPRateLimitPortKbpsThe maximum Kilobits-per-second of ICMP traffic that may be received inbound on the port. The value of this object must be interpreted under the context of hpICMPRateLimitControlMode. A value of 0 is not the same as disabling, but means instead that all ICMP traffic must be dropped.rw Integer32 .1.3.6.1.4.1.11.2.14.10.2.14.1.1.1.1.1.5 |
hpICMPRateLimitPortControlModeThe mode by which inbound ICMP traffic on this port will Rate-Limited. If icmpRateLimitPerPortOnly is configured, there will be a single maximum percentage-based rate for the entire port. If icmpRateLimitPerPortOnlyKbpsMode is configured, there will be a single maximum kilobits-per- second rate for the entire port. When ICMP rate-limiting is disabled, there are no maximum controls on inbound ICMP traffic for this port.rw Enumeration .1.3.6.1.4.1.11.2.14.10.2.14.1.1.1.1.1.6 |
hpICMPRateLimitPortIpPacketTypeThis object represents the type(s) of IP packet to which the specified ICMP rate-limit will be applied. The default is IPv4.rw Enumeration .1.3.6.1.4.1.11.2.14.10.2.14.1.1.1.1.1.7 |
hpICMPRateLimitNotifyPortIndexThe interface index associated with hpICMPRateLimitPortNotification event.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.11.2.14.10.2.14.1.1.2 |
hpicfBWMinEgressObjects OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.10.2.14.1.2 |
hpBWMinEgressPortConfig OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.10.2.14.1.2.1 |
hpBWMinEgressPortNumQueuesThe number of bandwidth minimum egress queues supported on this system.ro Integer32 .1.3.6.1.4.1.11.2.14.10.2.14.1.2.1.1 |
hpBWMinEgressPortPrctTableA table that contains information about the port's egress Guaranteed Minimum Bandwidth percent configurations on this switch. The number of entries in this table is determined by hpBWMinEgressPortNumQueues. The priority of the queues is in ascending order, starting with queue one being the lowest and queue hpBWMinEgressPortNumQueues being the highest. SEQUENCE OF HpBWMinEgressPortPrctEntry .1.3.6.1.4.1.11.2.14.10.2.14.1.2.1.2 |
hpBWMinEgressPortPrctEntryThe information associated with each port's egress Guaranteed Minimum Bandwidth percent configuration. HpBWMinEgressPortPrctEntry .1.3.6.1.4.1.11.2.14.10.2.14.1.2.1.2.1 |
hpBWMinEgressPortPrctQueueThe queue associated with this entry. The priority of the queues is in ascending order, starting with queue one being the lowest and queue hpBWMinEgressPortNumQueues being the highest. Integer32 .1.3.6.1.4.1.11.2.14.10.2.14.1.2.1.2.1.1 |
hpBWMinEgressPortPrctThe percentage of Guaranteed Minimum bandwidth to be assigned to this egress queue for this port. Total values for all queues must not exceed 100 percent.rw Integer32 .1.3.6.1.4.1.11.2.14.10.2.14.1.2.1.2.1.2 |
hpicfBWMinIngressObjects OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.10.2.14.1.3 |
hpBWMinIngressPortConfig OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.10.2.14.1.3.1 |
hpBWMinIngressPortNumQueuesThe number of bandwidth minimum ingress queues supported on this system.ro Integer32 .1.3.6.1.4.1.11.2.14.10.2.14.1.3.1.1 |
hpBWMinIngressPortPrctTableA table that contains information about the port's ingress Guaranteed Minimum Bandwidth percent configurations on this switch. The number of entries in this table is determined by hpBWMinIngressPortNumQueues. The priority of the queues is in ascending order, starting with queue one being the lowest and queue hpBWMinIngressPortNumQueues being the highest. SEQUENCE OF HpBWMinIngressPortPrctEntry .1.3.6.1.4.1.11.2.14.10.2.14.1.3.1.2 |
hpBWMinIngressPortPrctEntryThe information associated with each port's ingress Guaranteed Minimum Bandwidth percent configuration. HpBWMinIngressPortPrctEntry .1.3.6.1.4.1.11.2.14.10.2.14.1.3.1.2.1 |
hpBWMinIngressPortPrctQueueThe queue associated with this entry. The priority of the queues is in ascending order, starting with queue one being the lowest and queue hpBWMinIngressPortNumQueues being the highest. Integer32 .1.3.6.1.4.1.11.2.14.10.2.14.1.3.1.2.1.1 |
hpBWMinIngressPortPrctThe percentage of Guaranteed Minimum bandwidth to be assigned to this ingress queue for this port. Total values for all queues must not exceed 100 percent.rw Integer32 .1.3.6.1.4.1.11.2.14.10.2.14.1.3.1.2.1.2 |
hpicfRateLimitPortObjects OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.10.2.14.1.4 |
hpRateLimitPortConfig OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.10.2.14.1.4.1 |
hpEgressRateLimitPortNumQueuesThe number of egress rate-limiting queues supported on this system.ro Integer32 .1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.1 |
hpEgressRateLimitPortConfigTableA table that contains information about the port egress Rate-Limiting configurations on this switch. SEQUENCE OF HpEgressRateLimitPortConfigEntry .1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.2 |
hpEgressRateLimitPortConfigEntryThe information associated with each port's egress Rate-Limiting configuration. HpEgressRateLimitPortConfigEntry .1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.2.1 |
hpEgressRateLimitPortIndexThe ifIndex value which uniquely identifies a row in the Interfaces Table. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.2.1.1 |
hpEgressRateLimitPortControlModeThe mode by which this port will be Rate-Limited on egress. If egressRateLimitPerPortOnly is configured, there will be a single maximum percentage-based rate for the entire port. If egressRateLimitPerQueue is configured, the values for each of the queues indicate the maximum percentage of port traffic that may be transmitted by that queue. If egressRateLimitPerPortOnlyBpsMode is configured, there will be a single maximum bits-per-second rate for the entire port. If egressRateLimitPerPortOnlyKbpsMode is configured, there will be a single maximum kilobits-per-second rate for the entire port. If egressRateLimitPerQueueBpsMode is configured, the maximum transmission-rate values for each of the queues will be expressed in bits-per-second (again, the sum of these values must not exceed the maximum Bytes-per-second capability of the network link). The queues are defined under hpEgressRateLimitPortPrctTable. When egress rate-limiting is disabled, there are no maximum controls on egress for this port.rw Enumeration .1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.2.1.2 |
hpEgressRateLimitPortSingleControlPrctWhen hpEgressRateLimitPortControlMode is configured for egressRateLimitPerPortOnly, this value is the maximum percentage of traffic that may be transmitted by this port on egress.rw Integer32 .1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.2.1.3 |
hpEgressRateLimitPortSingleControlBpsWhen hpEgressRateLimitPortControlMode is configured for egressRateLimitPerPortOnlyBpsMode, this value is the maximum bits-per-second of traffic that may be transmitted by this port on egress.rwdeprecated Unsigned32 .1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.2.1.4 |
hpEgressRateLimitPortSingleControlKbpsWhen hpEgressRateLimitPortControlMode is configured for egressRateLimitPerPortOnlyKbpsMode, this value is the maximum kilobits-per-second of traffic that may be transmitted by this port on egress.rw Integer32 .1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.2.1.5 |
hpEgressRateLimitPortPrctTableA table that contains information about the port egress Rate-Limiting percent configurations on this switch. The number of entries in this table is determined by hpEgressRateLimitPortNumQueues. The priority of the queues is in ascending order, starting with queue one being the lowest priority and queue hpEgressRateLimitPortNumQueues being the highest priority. SEQUENCE OF HpEgressRateLimitPortPrctEntry .1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.3 |
hpEgressRateLimitPortPrctEntryThe information associated with each port's egress Rate-Limiting percent configuration. HpEgressRateLimitPortPrctEntry .1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.3.1 |
hpEgressRateLimitPortPrctQueueThe queue associated with this entry. The priority o of the queues is in ascending order, starting with queue one being the lowest and queue hpEgressRateLimitgressPortNumQueues being the highest. Integer32 .1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.3.1.1 |
hpEgressRateLimitPortPrctThe maximum percentage of traffic that may be transmitted by this port's queue on egress. hpEgressRateLimitPortControlMode must be configured to use egressRateLimitPerQueue for this to take effect. A value of 0-percent for any queue means that no traffic will ever be transmitted on this port for that egress queue.rw Integer32 .1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.3.1.2 |
hpEgressRateLimitPortBpsTableA table that contains information about the port egress Rate-Limiting bits-per-second configurations on this switch. The number of entries in this table is determined by hpEgressRateLimitPortNumQueues. The priority of the queues is in ascending order, starting with queue one being the lowest priority and queue hpEgressRateLimitPortNumQueues being the highest priority queue.deprecated SEQUENCE OF HpEgressRateLimitPortBpsEntry .1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.4 |
hpEgressRateLimitPortBpsEntryThe information associated with each port's egress Rate-Limiting bits-per-second configuration.deprecated HpEgressRateLimitPortBpsEntry .1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.4.1 |
hpEgressRateLimitPortBpsQueueThe queue associated with this entry. The priority of the queues is in ascending order, starting with queue one being the lowest and queue hpEgressRateLimitgressPortNumQueues being the highest.deprecated Integer32 .1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.4.1.1 |
hpEgressRateLimitPortBpsThe maximum bits-per-second of traffic that may be transmitted by this port's queue on egress. hpEgressRateLimitPortControlMode must be configured to use egressRateLimitPerQueue for this to take effect. A value of 0-percent for any queue means that no traffic will ever be transmitted on this port for that egress queue. The values for each queue must not exceed the bits-per-second capability of the current network link speed.rwdeprecated Unsigned32 .1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.4.1.2 |
hpicfIngressRateLimitPortObjects OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.10.2.14.1.5 |
hpRateLimitIngressPortConfig OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.10.2.14.1.5.1 |
hpIngressRateLimitPortNumQueuesThe number of ingress rate-limiting queues supported on this system.ro Integer32 .1.3.6.1.4.1.11.2.14.10.2.14.1.5.1.1 |
hpIngressRateLimitPortConfigTableA table that contains information about the port ingress Rate-Limiting configurations on this switch. SEQUENCE OF HpIngressRateLimitPortConfigEntry .1.3.6.1.4.1.11.2.14.10.2.14.1.5.1.2 |
hpIngressRateLimitPortConfigEntryThe information associated with each port's ingress Rate-Limiting configuration. HpIngressRateLimitPortConfigEntry .1.3.6.1.4.1.11.2.14.10.2.14.1.5.1.2.1 |
hpIngressRateLimitPortIndexThe ifIndex value which uniquely identifies a row in the Interfaces Table. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.11.2.14.10.2.14.1.5.1.2.1.1 |
hpIngressRateLimitPortControlModeThe mode by which this port will be Rate-Limited on ingress. If ingressRateLimitPerPortOnly is configured, there will be a single maximum percentage-based rate for the entire port. If ingressRateLimitPerQueue is configured, the values for each of the queues indicate the maximum percentage of port traffic that may be transmitted by that queue. If ingressRateLimitPerPortOnlyBpsMode is configured, there will be a single maximum bits-per-second rate for the entire port. If ingressRateLimitPerPortOnlyKbpsMode is configured, there will be a single maximum kilobits-per-second rate for the entire port. If ingressRateLimitPerQueueBpsMode is configured, the maximum transmission-rate values for each of the queues will be expressed in bits-per-second (again, the sum of these values must not exceed the maximum Bytes-per-second capability of the network link). The queues are defined under hpIngressRateLimitPortPrctTable. When ingress rate-limiting is disabled, there are no maximum controls on ingress for this port.rw Enumeration .1.3.6.1.4.1.11.2.14.10.2.14.1.5.1.2.1.2 |
hpIngressRateLimitPortSingleControlPrctWhen hpIngressRateLimitPortControlMode is configured for ingressRateLimitPerPortOnly, this value is the maximum percentage of traffic that may be transmitted by this port on egress.rw Integer32 .1.3.6.1.4.1.11.2.14.10.2.14.1.5.1.2.1.3 |
hpIngressRateLimitPortSingleControlBpsWhen hpIngressRateLimitPortControlMode is configured for ingressRateLimitPerPortOnlyBpsMode, this value is the maximum bits-per-second of traffic that may be transmitted by this port on ingress.rwdeprecated Unsigned32 .1.3.6.1.4.1.11.2.14.10.2.14.1.5.1.2.1.4 |
hpIngressRateLimitPortSingleControlKbpsWhen hpIngressRateLimitPortControlMode is configured for ingressRateLimitPerPortOnlyKbpsMode, this value is the maximum kilobits-per-second of traffic that may be transmitted by this port on ingress.rw Integer32 .1.3.6.1.4.1.11.2.14.10.2.14.1.5.1.2.1.5 |
hpIngressRateLimitPortPrctTableA table that contains information about the port ingress Rate-Limiting percent configurations on this switch. The number of entries in this table is determined by hpIngressRateLimitPortNumQueues. The priority of the queues is in ascending order, starting with queue one being the lowest priority and queue hpIngressRateLimitPortNumQueues being the highest priority. SEQUENCE OF HpIngressRateLimitPortPrctEntry .1.3.6.1.4.1.11.2.14.10.2.14.1.5.1.3 |
hpIngressRateLimitPortPrctEntryThe information associated with each port's ingress Rate-Limiting percent configuration. HpIngressRateLimitPortPrctEntry .1.3.6.1.4.1.11.2.14.10.2.14.1.5.1.3.1 |
hpIngressRateLimitPortPrctQueueThe queue associated with this entry. The priority of the queues is in ascending order, starting with queue one being the lowest and queue hpIngressRateLimitgressPortNumQueues being the highest. Integer32 .1.3.6.1.4.1.11.2.14.10.2.14.1.5.1.3.1.1 |
hpIngressRateLimitPortPrctThe maximum percentage of traffic that may be transmitted by this port's queue on ingress. hpIngressRateLimitPortControlMode must be configured to use ingressRateLimitPerQueue for this to take effect. A value of 0-percent for any queue means that no traffic will ever be transmitted on this port for that ingress queue. The values for each queue must not exceed 100 percent.rw Integer32 .1.3.6.1.4.1.11.2.14.10.2.14.1.5.1.3.1.2 |
hpIngressRateLimitPortBpsTableA table that contains information about the port ingress Rate-Limiting bits-per-second configurations on this switch. The number of entries in this table is determined by hpIngressRateLimitPortNumQueues. The priority of the queues is in ascending order, starting with queue one being the lowest priority and queue hpIngressRateLimitPortNumQueues being the highest priority queue.deprecated SEQUENCE OF HpIngressRateLimitPortBpsEntry .1.3.6.1.4.1.11.2.14.10.2.14.1.5.1.4 |
hpIngressRateLimitPortBpsEntryThe information associated with each port's egress Rate-Limiting bits-per-second configuration.deprecated HpIngressRateLimitPortBpsEntry .1.3.6.1.4.1.11.2.14.10.2.14.1.5.1.4.1 |
hpIngressRateLimitPortBpsQueueThe queue associated with this entry. The priority of the queues is in ascending order, starting with queue one being the lowest and queue hpIngressRateLimitgressPortNumQueues being the highest.deprecated Integer32 .1.3.6.1.4.1.11.2.14.10.2.14.1.5.1.4.1.1 |
hpIngressRateLimitPortBpsThe maximum bits-per-second of traffic that may be transmitted by this port's queue on ingress. hpIngressRateLimitPortControlMode must be configured to use ingressRateLimitPerQueue for this to take effect. A value of 0-percent for any queue means that no traffic will ever be transmitted on this port for that ingress queue. The values for each queue must not exceed the bits-per-second capability of the current network link speed.rwdeprecated Unsigned32 .1.3.6.1.4.1.11.2.14.10.2.14.1.5.1.4.1.2 |
hpicfIngressBcastLimitPortObjects OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.10.2.14.1.6 |
hpBcastLimitIngressPortConfig OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.10.2.14.1.6.1 |
hpIngressBcastLimitPortConfigTableA table that contains information about the port ingress Broadcast-Limiting configurations on this switch. SEQUENCE OF HpIngressBcastLimitPortConfigEntry .1.3.6.1.4.1.11.2.14.10.2.14.1.6.1.1 |
hpIngressBcastLimitPortConfigEntryThe information associated with each port's ingress Broadcast-Limiting configuration. HpIngressBcastLimitPortConfigEntry .1.3.6.1.4.1.11.2.14.10.2.14.1.6.1.1.1 |
hpIngressBcastLimitPortIndexThe ifIndex value which uniquely identifies a row in the Interfaces Table. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.11.2.14.10.2.14.1.6.1.1.1.1 |
hpIngressBcastLimitPortControlModeThe mode by which this port will be Broadcast-Limited on ingress. If ingressBcastLimitPerPortOnly is configured, there will be a single maximum percentage-based Bcast for the entire port. If ingressBcastLimitPerPortOnlyKbpsMode is configured, there will be a single maximum kilobits-per-second maximum broadcast traffic rate for the entire port.When ingress Bcast-limiting is disabled, there are no maximum controls on ingress for this port.rw Enumeration .1.3.6.1.4.1.11.2.14.10.2.14.1.6.1.1.1.2 |
hpIngressBcastLimitPortSingleControlPrctWhen hpIngressBcastLimitPortControlMode is configured for ingressBcastLimitPerPortOnly, this value is the maximum percentage of traffic that may be transmitted by this port on ingress.rw Integer32 .1.3.6.1.4.1.11.2.14.10.2.14.1.6.1.1.1.3 |
hpIngressBcastLimitPortSingleControlKbpsWhen hpIngressBcastLimitPortControlMode is configured for ingressBcastLimitPerPortOnlyKbpsMode, this value is the maximum kilobits-per-second of broadcast traffic that may be transmitted by this port on ingress.rw Integer32 .1.3.6.1.4.1.11.2.14.10.2.14.1.6.1.1.1.4 |
hpicfIngressMcastLimitPortObjects OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.10.2.14.1.7 |
hpMcastLimitIngressPortConfig OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.10.2.14.1.7.1 |
hpIngressMcastLimitPortConfigTableA table that contains information about the port ingress Multicast-Limiting configurations on this switch. SEQUENCE OF HpIngressMcastLimitPortConfigEntry .1.3.6.1.4.1.11.2.14.10.2.14.1.7.1.1 |
hpIngressMcastLimitPortConfigEntryThe information associated with each port's ingress Multicast-Limiting configuration. HpIngressMcastLimitPortConfigEntry .1.3.6.1.4.1.11.2.14.10.2.14.1.7.1.1.1 |
hpIngressMcastLimitPortIndexThe ifIndex value which uniquely identifies a row in the Interfaces Table. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.11.2.14.10.2.14.1.7.1.1.1.1 |
hpIngressMcastLimitPortControlModeThe mode by which this port will be Multicast-Limited on ingress. If ingressMcastLimitPerPortOnly is configured, there will be a single maximum percentage-based Mcast for the entire port. If ingressMcastLimitPerPortOnlyKbpsMode is configured, there will be a single maximum kilobits-per-second maximum multicast traffic rate for the entire port. When ingress Mcast-limiting is disabled, there are no maximum controls on ingress for this port.rw Enumeration .1.3.6.1.4.1.11.2.14.10.2.14.1.7.1.1.1.2 |
hpIngressMcastLimitPortSingleControlPrctWhen hpIngressMcastLimitPortControlMode is configured for ingressMcastLimitPerPortOnly, this value is the maximum percentage of multicast traffic that may be transmitted by this port on ingress.rw Integer32 .1.3.6.1.4.1.11.2.14.10.2.14.1.7.1.1.1.3 |
hpIngressMcastLimitPortSingleControlKbpsWhen hpIngressMcastLimitPortControlMode is configured for ingressMcastLimitPerPortOnlyKbpsMode, this value is the maximum kilobits-per-second of multicast traffic that may be transmitted by this port on ingress.rw Integer32 .1.3.6.1.4.1.11.2.14.10.2.14.1.7.1.1.1.4 |
hpicfRateLimitConformance OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.10.2.14.2 |
hpicfRateLimitGroups OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.10.2.14.2.1 |
hpICMPRateLimitPortConfigGroupA collection of objects providing configuration to ICMP rate limiting on an interface.deprecated Unknown .1.3.6.1.4.1.11.2.14.10.2.14.2.1.1 |
hpICMPRateLimitPortNotifyGroupA collection of notifications used to indicate ICMP rate limiting on an interface events. Unknown .1.3.6.1.4.1.11.2.14.10.2.14.2.1.2 |
hpBWMinIngressPortConfigGroupA collection of objects providing configuration to Guaranteed Minimum ingress bandwidth on an interface. Unknown .1.3.6.1.4.1.11.2.14.10.2.14.2.1.3 |
hpBWMinEgressPortConfigGroupA collection of objects providing configuration to Guaranteed Minimum egress bandwidth on an interface. Unknown .1.3.6.1.4.1.11.2.14.10.2.14.2.1.4 |
hpEgressRateLimitPortConfigGroupA collection of objects providing configuration to Egress Rate-Limiting on an interface.deprecated Unknown .1.3.6.1.4.1.11.2.14.10.2.14.2.1.5 |
hpIngressRateLimitPortConfigGroupA collection of objects providing configuration to Ingress Rate-Limiting on an interface.deprecated Unknown .1.3.6.1.4.1.11.2.14.10.2.14.2.1.6 |
hpICMPRateLimitPortConfigGroup2This replaces the deprecated hpICMPRateLimitPortConfigGroup. A collection of objects providing configuration to ICMP rate limiting on an interface.deprecated Unknown .1.3.6.1.4.1.11.2.14.10.2.14.2.1.7 |
hpEgressRateLimitPortConfigGroup2This replaces the deprecated hpEgressRateLimitPortConfigGroup. A collection of objects providing configuration to Egress Rate-Limiting on an interface. Unknown .1.3.6.1.4.1.11.2.14.10.2.14.2.1.8 |
hpIngressRateLimitPortConfigGroup2This replaces the deprecated hpIngressRateLimitPortConfigGroup. A collection of objects providing configuration to Ingress Rate-Limiting on an interface. Unknown .1.3.6.1.4.1.11.2.14.10.2.14.2.1.9 |
hpBcastLimitIngressPortConfigGroupA collection of objects providing configuration to Ingress Broadcast Limiting on an interface. Unknown .1.3.6.1.4.1.11.2.14.10.2.14.2.1.10 |
hpMcastLimitIngressPortConfigGroupA collection of objects providing configuration to Ingress Multicast Limiting on an interface. Unknown .1.3.6.1.4.1.11.2.14.10.2.14.2.1.11 |
hpBcastLimitIngressPortConfigGroup2This replaces the deprecated hpBcastLimitIngressPortConfigGroup. A collection of objects providing configuration of Ingress Broadcast Limiting on an interface. Unknown .1.3.6.1.4.1.11.2.14.10.2.14.2.1.12 |
hpMcastLimitIngressPortConfigGroup2This replaces the deprecated hpMcastLimitIngressPortConfigGroup A collection of objects providing configuration of Ingress Multicast Limiting on an interface. Unknown .1.3.6.1.4.1.11.2.14.10.2.14.2.1.13 |
hpICMPRateLimitPortConfigGroup3This replaces the deprecated hpICMPRateLimitPortConfigGroup2. A collection of objects providing configuration for ICMP rate limiting on an interface. Unknown .1.3.6.1.4.1.11.2.14.10.2.14.2.1.14 |
hpicfRateLimitCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.10.2.14.2.2 |
hpicfRateLimitComplianceThe compliance statement for device support of HP-ICF-RATE-LIMIT MIB.deprecated Unknown .1.3.6.1.4.1.11.2.14.10.2.14.2.2.1 |
hpicfRateLimitCompliance1The compliance statement for device support of HP-ICF-RATE-LIMIT MIB.deprecated Unknown .1.3.6.1.4.1.11.2.14.10.2.14.2.2.2 |
hpicfRateLimitCompliance2The compliance statement for device support of HP-ICF-RATE-LIMIT MIB. Unknown .1.3.6.1.4.1.11.2.14.10.2.14.2.2.3 |
hpICMPRateLimitPortNotificationThis notification indicates limit has exceeded. NOTIFICATION-TYPE .1.3.6.1.4.1.11.2.14.12.5.0.1 |