HP-ICF-POE-MIB
This MIB module describes management objects used to manage Power Source Equipment (PSE).
Main OID:
hpicfPoe.1.3.6.1.4.1.11.2.14.11.1.9.1
21
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
21 total| Object Name |
|---|
hpicfPOE OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.1.9 |
hpicfPoeThis MIB module describes management objects used to manage Power Source Equipment (PSE). MODULE-IDENTITY .1.3.6.1.4.1.11.2.14.11.1.9.1 |
hpicfPoePethPsePortTableThis table suplements the table 'pethPsePortTable' in ieee802af.mib. SEQUENCE OF HpicfPoePethPsePortEntry .1.3.6.1.4.1.11.2.14.11.1.9.1.1 |
hpicfPoePethPsePortEntryThe fields in these entries will be used to supplement fields in 'pethPsePortEntry in ieee802af.mib. HpicfPoePethPsePortEntry .1.3.6.1.4.1.11.2.14.11.1.9.1.1.1 |
hpicfPoePethPsePortCurrentThis field specifies the current supplied at this port. This value is specified in milli amperes(mA).ro INTEGER .1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.1 |
hpicfPoePethPsePortVoltageThis field specifies the Voltage supplied at this port. This value is specified in 10's of volts (dV)ro INTEGER .1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.2 |
hpicfPoePethPsePortPowerThis field specifies the Power supplied at this port. This value is specified in milliwatts (mW).ro INTEGER .1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.3 |
hpicfPoePethPsePortPowerAllocateByThis field specifies the power allocation method for this port. The default value is usage.rw Enumeration .1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.4 |
hpicfPoePethPsePortPowerValueThis field specifies the power allocation defined for this port. This value is specified in Watts (W).rw INTEGER .1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.5 |
hpicfPoePethPsePortLLDPDetectThis field specifies if power should be allocated using LLDP advertised information regarding the PD.rw Enumeration .1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.6 |
hpicfPoePethPsePortPoePlusPowerValueThis field specifies the power allocation defined for this port. Use this object for equipment supporting high power, i.e, greater than 15 Watts. This value is specified in Watts (W). Maximum supported is 33Wrw INTEGER .1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.7 |
hpicfPoeConformance OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.1.9.1.2 |
hpicfPoeCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.1.9.1.2.1 |
hpicfPoeComplianceA compliance statement for HP Routing switches with PoE capabilitydeprecated Unknown .1.3.6.1.4.1.11.2.14.11.1.9.1.2.1.1 |
hpicfPoeCompliance1A compliance statement for HP Routing switches with PoE capability Unknown .1.3.6.1.4.1.11.2.14.11.1.9.1.2.1.2 |
hpicfPoeGroups OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.1.9.1.2.2 |
hpicfPoePethPsePortTableGroupA collection of objects allowing configuration of PoE PSE Port table Unknown .1.3.6.1.4.1.11.2.14.11.1.9.1.2.2.1 |
hpicfPoeGlobalGroupA collection of objects related to the global configuration of POE on a given chassis Unknown .1.3.6.1.4.1.11.2.14.11.1.9.1.2.2.2 |
hpicfPoeAllowPreStdDetectThis object is used to configure the default POE power detection mode. A value of TRUE - indicates that power pre-802.3af-standard devices. A value of FALSE - indicates that only pre-802.3af compliant devices are allowed. The default value is true.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.1.9.1.3 |
hpicfPoePowerRedundancyThis object is used to configure the POE power redundancy mode. A value of none(1) - means that all available power can be allocated to powered devices. A value of nPlus1(2) - means that one of the highest power supplies is held in reserve and that in the event of a single power supply failure, no no powered devices will be shut down. A value of full(3) - means that half of the available power supplies are held in reserve. The default value is none(1).rw Enumeration .1.3.6.1.4.1.11.2.14.11.1.9.1.4 |
hpicfPoeExtPwrSupplyCountThis object is used to configure the number of external power supplies expected to be connected to the chassis. The default value is 1.rw Integer32 .1.3.6.1.4.1.11.2.14.11.1.9.1.5 |