HP-ICF
AI MIB Summary
Standard SNMP MIB module defining data structures for HP-ICF.
541
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
541 total| Object Name |
|---|
hp OBJECT IDENTIFIER .1.3.6.1.4.1.11 |
RFC1155-SMI Unknown .1.3.6.1.4.1.11 |
nm OBJECT IDENTIFIER .1.3.6.1.4.1.11.2 |
hpSystem OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3 |
netElement OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7 |
bridge OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.1 |
bridge1010 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.1.1 |
bridgeRemote OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.1.2 |
eswitch OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.1.3 |
router OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.2 |
icfRouterER OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.2.1 |
icfRouterTR OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.2.2 |
icfRouterSR OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.2.3 |
icfRouterFR OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.2.4 |
icfRouterLR OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.2.5 |
icfRouterBR OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.2.6 |
icfRouterPR OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.2.7 |
icfRouter650 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.2.8 |
icfRouter650Engine OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.2.8.2 |
icfRouter650Port4E OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.2.8.3 |
icfRouter650Port4S OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.2.8.4 |
icfRouter650Port4T OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.2.8.5 |
icfRouter230 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.2.9 |
icfRouter250 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.2.10 |
icfRouter255 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.2.11 |
icfRouter210 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.2.12 |
hub OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.5 |
etherTwist12 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.5.1 |
fiberOptic OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.5.3 |
etherTwist48 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.5.4 |
thinLAN OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.5.5 |
etherTwist24S OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.5.6 |
advStack12 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.5.7 |
advStack24 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.5.8 |
advStack48 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.5.9 |
advStackVg15 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.5.10 |
advStackU8 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.5.11 |
advStackU16 OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.5.12 |
chassis OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.8 |
repeaterAgent OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.8.1 |
chassisAgents OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.8.2 |
icfVgAgent OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.8.2.1 |
icfEnetAgent OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.8.2.2 |
icfSensors OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.8.3 |
icfPowerSupplySensor OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.8.3.1 |
icfFanSensor OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.8.3.2 |
icfTemperatureSensor OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.8.3.3 |
icf OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14 |
icfCommon OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.1 |
thresholdTrapA thresholdTrap(0) is specific to ICF devices. It
signifies that the threshold entity in the device
has detected that the object identified by
evthObject has exceeded the threshold identified
by evthThreshold during the time interval
evthTimeInterval. After this condition occurs, it
will not reoccur until the the object identified
by evthObject falls below evthHysteresis for the
duration of evthTimeInterval. TRAP-TYPE .1.3.6.1.4.1.11.2.14.1.0.0 |
lastSetErrorProvide more detailed, enterprise specific error
type. Any error resulting from a SET request will
cause this object to be updated, and the previous
value overwritten. A management entity may
retrieve more detailed error information than that
implied by the pdu's ErrorStatus, especially in
the case of a genErr.
In SNMPv2, there are several more error codes which
provide most of the information that is provided
by the above codes. Therefore, this object is now
obsolete.roobsolete Enumeration .1.3.6.1.4.1.11.2.14.1.1 |
passwordThis is the encrypted password for the device. The
algorithm used for the encryption process is HP
proprietary. Third party vendor support is provided by
not setting a password on the device, and using the
community name 'public'. This object is now obsolete,
and is supported only on 'D' revision EtherTwist hubs
and bridges and earlier. It has been superseded by
icfSecurPassword.rwobsolete OCTET STRING .1.3.6.1.4.1.11.2.14.1.2 |
resetWhen the reset object is set to to 'warm' it
results in a 'warm' reset, which does not clear
the parameters in NOVRAM to factory defaults. When
set to 'cold', it results in NOVRAM being set to
factory defaults. When this object is set, the
agent replies, dallies a short time to allow the
reply to be emitted from the device, then performs
the reset. When read, this object always returns
0.
This object is now obsolete. It has been replaced by
hpicfReset.rwobsolete Enumeration .1.3.6.1.4.1.11.2.14.1.3 |
selfTestSelf test is invoked by setting this flag to
'stExecute. When the object changes to
'stSuccess', the test has completed successfully.
Icf devices will 'hard-fail' if the test does not
succeed.
This object is now obsolete. It has been replaced by
hpicfSelfTest.rwobsolete INTEGER --{ -- stSuccess(0), -- stExecute(1) --} .1.3.6.1.4.1.11.2.14.1.4 |
semaphoreThis object allows a set of objects to be locked.
The lock is only assured by the 'cooperation' of
other management entities; they must wait until
the lock is cleared (to value zero) prior to
setting the lock. When this object is set to a
management entity's IP address, if no other
management entity has previously set the lock, the
set will succeed. Otherwise, an error (BadValue)
will be returned. It is the responsibility of the
owning management entity to clear the lock when
the transactions complete. To protect against a
management entity failure during a locked
transaction, the agent is NOT responsible for
verifying which management entity is performing
transactions on locked objects; thus, any
management entity can clear this object at any
time. The agent does not do anything with this
object except disallow multiple sets of different
IP addresses (unless the object has been cleared
to zero). This means management entities can use
this for locking any valid transactions on defined
sets of objects. This object can also be used on
IPX networks by specifying the low 4 bytes of the
station address for the IpAddress.
This object is now obsolete. Individual groups of
objects now maintain their own locking mechanisms.rwobsolete IpAddress .1.3.6.1.4.1.11.2.14.1.5 |
discovery OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.1.6 |
pollResponseFlag indicating whether device should respond to
multicast SNMP PDUs. When set 'true', the device
will respond to multicast SNMP PDU's. Otherwise,
the response is discarded.rwobsolete INTEGER --{ -- false(0), -- true(1) --} .1.3.6.1.4.1.11.2.14.1.6.1 |
announceAddressWhen set to any MAC multicast address, the
device will transmit three identical packets, each
with the MAC source set to the device's MAC
address, the MAC destination to the multi-cast
address, the destination SAP is F8, and the
destination HP XSAP is 165D. These packets will
traverse other ICF devices, allowing them to learn
the port connectivity of the multicasting
device.rwdeprecated MacAddress (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.1.6.2 |
mapAddressWhen this object is set a map address search
begins. If the address is detected on only one
port, then the mapPort object is set to the port
number on which the address was detected.
This object has been deprecated.rwdeprecated OCTET STRING .1.3.6.1.4.1.11.2.14.1.6.3 |
mapStateThis object will be set to 'psNone' if the
address set in the mapAddress object has not been
received on any of the device's interface/ports.
It will be set to 'psSingle' if the mapAddress has
been detected on only one interface/port. It will
be set to 'psMany' if the mapAddress has been
detected on more than one interface/port.
This object has been deprecated.rodeprecated INTEGER --{ -- psNone(0), -- psSingle(1), -- psMany(2) --} .1.3.6.1.4.1.11.2.14.1.6.4 |
mapPortThe port number on which the map address was
detected. If map state is 'psNone' or 'psMany'
then this object is not valid.
This object has been deprecated.rodeprecated INTEGER .1.3.6.1.4.1.11.2.14.1.6.5 |
ipSubnetMaskThis object is the IP subnet mask.
This object is obsolete. Management applications
should retrieve the ipAddrTable, which contains the
ipAdEntNetMask object for each interface on the
device.roobsolete IpAddress .1.3.6.1.4.1.11.2.14.1.6.6 |
icfEvent OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.1.7 |
eventNotificationNode OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.1.7.1 |
evtIpNotifyThe network address of the manager node which is
to receive the event notification trap.
This functionality is currently duplicated in the
authorized manager list.rwobsolete IpAddress .1.3.6.1.4.1.11.2.14.1.7.1.1 |
evtIpxNotifyThe IPX address of the manager node which is to
receive the event notification trap.
This functionality is currently duplicated in the
authorized manager list.rwobsolete OCTET STRING .1.3.6.1.4.1.11.2.14.1.7.1.2 |
evtTableA list of event entries for event processing.obsolete SEQUENCE OF EvtEntry .1.3.6.1.4.1.11.2.14.1.7.2 |
evtIndexThe index value which uniquely identifies the
event to which this entry is applicable.roobsolete Enumeration .1.3.6.1.4.1.11.2.14.1.7.2.1 |
evtArmThis object arms and disarms events. Events are
implicitly rearmed, that is, once an event occurs,
it is rearmed. Sets to the intrusionEvent
instance of this object are ignored, since
intrusion events are actually armed through the
hubSecPtAlarmEnable object.rwobsolete INTEGER --{ -- off(0), -- on(1) --} .1.3.6.1.4.1.11.2.14.1.7.2.2 |
evtTimeSinceOccurrenceThis object specifies the number of centiseconds
since this event last occurred.roobsolete TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.11.2.14.1.7.2.3 |
evtThresholdTableA list of event entries for event processing.obsolete SEQUENCE OF EvtThresholdEntry .1.3.6.1.4.1.11.2.14.1.7.3 |
evthIndexThe index value which uniquely identifies the
event to which this entry is applicable.roobsolete INTEGER ( 1..5 ) .1.3.6.1.4.1.11.2.14.1.7.3.1 |
evthArmThis object arms and disarms events. The
notification node, the associated event object,
threshold, hysteresis, and time interval should
all be set before an event is armed. The objects
do not need to be re-set if the existing values
are acceptable. The device will refuse to arm an
event with uninitialized objects. Once armed, if
the threshold is met or exceeded during the event
time interval, a trap PDU is sent to the
eventNotificationNode. Subsequently, the
monitored object must fall to or below the
hysteresis before another trap can be sent via the
threshold mechanism. The hysteresis may equal
threshold. Events are implicitly rearmed, that is,
once an event occurs, it is rearmed. Setting this
object to 'on' will result in a genErr in any of
the following cases: object not set; cannot set an
event on this object; time interval not set;
threshold not set.rwobsolete INTEGER --{ -- off(0), -- on(1) --} .1.3.6.1.4.1.11.2.14.1.7.3.2 |
evthObjectThe data of this object is itself an OBJECT
IDENTIFIER which selects the mib object and
instance that is to be monitored for the event.
Only types INTEGER and Counter are allowed.rwobsolete OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.1.7.3.3 |
evthThresholdThe threshold against which the variable
specified in evthObject is tested over the time
interval specified in the evthTimeInterval When
the threshold is met or exceeded, the event is
triggered. The event will not trigger again until
the variable falls to or below the evthHysteresis
value, and then meets or exceeds the threshold.rwobsolete INTEGER .1.3.6.1.4.1.11.2.14.1.7.3.4 |
evthHysteresisThe low value which the variable specified in
evthObject must fall to or below after exceeding
evthThreshold before the event can re-occur when
the threshold is met or exceeded.rwobsolete INTEGER .1.3.6.1.4.1.11.2.14.1.7.3.5 |
evthTimeIntervalThe time interval over which the variable
specified in the evthObject is sampled.rwobsolete TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.11.2.14.1.7.3.6 |
evthTimeSinceOccurrenceThis object specifies the number of centiseconds
since this event was last triggered.roobsolete TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.11.2.14.1.7.3.7 |
linkTest OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.1.8 |
linkTestAddress OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.1.8.1 |
linkTest802MacAddressIf this object is set to the MAC address of a
node to link test in the same PDU that sets
linkTestRepetitions to a nonzero value, the link
test performed will use IEEE 802 Test frames.
Note that setting more than one of
linkTest802MacAddress, linkTestIpAddress, and
linkTestIpxAddress to a non-null value in the same
PDU will result in a genErr.rwdeprecated OCTET STRING .1.3.6.1.4.1.11.2.14.1.8.1.1 |
linkTestIpAddressIf this object is set to the network address of a
node to link test in the same PDU that sets
linkTestRepetitions to a nonzero value, the link
test performed will use ICMP Echo packets.
Note that setting more than one of
linkTest802MacAddress, linkTestIpAddress, and
linkTestIpxAddress to a non-null value in the same
PDU will result in a genErr.rwdeprecated IpAddress .1.3.6.1.4.1.11.2.14.1.8.1.2 |
linkTestIpxAddressIf this object is set to the IPX address of a
node to link test in the same PDU that sets
linkTestRepetitions to a nonzero value, the link
test performed will use IPX diagnostic packets.
Note that setting more than one of
linkTest802MacAddress, linkTestIpAddress, and
linkTestIpxAddress to a non-null value in the same
PDU will result in a genErr.rwdeprecated OCTET STRING .1.3.6.1.4.1.11.2.14.1.8.1.3 |
linkTestRepetitionsThe number of link tests that the device is to
complete. When this object is set to a non-zero
value, the linkTestSuccess object is zeroed and
the device begins a link test using IEEE 802.2
Test frames, ICMP Echo packets, or IPX diagnostic
packets depending on the address selected. Link
test results are contained in the link test
success object. This object's value decrements
(to zero) as the test proceeds. The test may be
canceled at any point by setting this object to
0.rwdeprecated INTEGER .1.3.6.1.4.1.11.2.14.1.8.2 |
linkTestSuccessFor every successful link test, this counter is
incremented. When link tests are completed, this
counter contains the total number of successful
tests.rodeprecated INTEGER .1.3.6.1.4.1.11.2.14.1.8.3 |
linkTestTimeoutThe time interval over which a link test response
must be received, or the test is counted as
failed.rwdeprecated TimeTicks -- .1.3.6.1.4.1.11.2.14.1.8.4 |
icf8023MacTableA list of icf8023Mac entries.obsolete SEQUENCE OF Icf8023MacEntry .1.3.6.1.4.1.11.2.14.1.9 |
icf8023MacIndexThe index value which uniquely identifies the
port to which this entry is applicable. The port
identified by a particular value of this index on
a hub is the same port as identified by the same
value of rptrPortIndex. Note that since this hub
always has exactly 1 port group, there is no group
index for this table. For a bridge, the port
identified by a particular value of this index is
the same port identified by the same value of
ifIndex.roobsolete INTEGER .1.3.6.1.4.1.11.2.14.1.9.1 |
icf8023MacInBroadcastPktsCount of the broadcast packets received.roobsolete Counter .1.3.6.1.4.1.11.2.14.1.9.2 |
icf8023MacOutBroadcastPktsCount of the broadcast packets transmitted.roobsolete Counter .1.3.6.1.4.1.11.2.14.1.9.3 |
icf8023MacInMulticastPktsCount of the multicast packets received.roobsolete Counter .1.3.6.1.4.1.11.2.14.1.9.4 |
icf8023MacOutMulticastPktsCount of the multicast packets transmitted.roobsolete Counter .1.3.6.1.4.1.11.2.14.1.9.5 |
icf8023MacRuntsThe number of media frames encountered that were
too short (by ethernet/802.3 standards).roobsolete Counter .1.3.6.1.4.1.11.2.14.1.9.6 |
icf8023MacGiantsThe number of media frames encountered that were
too long (by ethernet/802.3 standards).roobsolete Counter .1.3.6.1.4.1.11.2.14.1.9.7 |
icf8023MacMissedPktErrorsThe number of frames lost due to lack of
resources (e.g. ring buffers, memory buffers,
etc).roobsolete Counter .1.3.6.1.4.1.11.2.14.1.9.8 |
icf8023MacExcessDeferralsThe number of times a frame could not be sent due
to excess deferrals because another node was
transmitting continually.roobsolete Counter .1.3.6.1.4.1.11.2.14.1.9.9 |
icf8023MacTotalMediaErrorsCount of all possible medium transmit and receive
errors, such as crc, alignment, sequence, length,
excess etc. The purpose of this object is to
support aggregate LAN medium errors for event
processing. Collisions and runts are not
considered an error.roobsolete Counter .1.3.6.1.4.1.11.2.14.1.9.10 |
icf8023MacSpuriousIntrsThe number of times that the network interface
for this port generated a spurious hardware
interrupt. A non-zero value for this object
indicates a potential hardware problem.roobsolete Counter .1.3.6.1.4.1.11.2.14.1.9.11 |
icfDownload OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.1.10 |
icfDownloadAddress OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.1.10.1 |
icfDownloadIpAddressThe IP address of the TFTP server to download
firmware from.rwobsolete IpAddress .1.3.6.1.4.1.11.2.14.1.10.1.1 |
icfDownloadIpxAddressThe IPX address of the TFTP server to download
firmware from.rwobsolete OCTET STRING .1.3.6.1.4.1.11.2.14.1.10.1.2 |
icfDownloadFilenameFilename and path of file to download (maximum
length of 63 characters + NULL).rwobsolete DisplayString .1.3.6.1.4.1.11.2.14.1.10.2 |
icfHub OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.2 |
linkBeatTrapA linkBeatTrap(3) is device type specific to ICF
hubs. It signifies that the hub hardware has
detected a change of state in a port's link beat
status. The current value of the port's link beat
status is returned in the PDU. TRAP-TYPE .1.3.6.1.4.1.11.2.14.2.0.3 |
segmentationTrapA segmentationTrap(4) is device type specific to
ICF hubs. It signifies that the hub hardware has
detected a change of state in a port's
segmentation status. The current value of the
port's segmentation status is returned in the
PDU. TRAP-TYPE .1.3.6.1.4.1.11.2.14.2.0.4 |
backupLinkTrapA backupLinkTrap(5) is device type specific to
most ICF hubs. It signifies that there has been a
change in state of rptrPortAdminStatus for a
backup port on the hub. The new value of
rptrPortAdminStatus is returned in the PDU.
Note that in EtherTwist hubs with revision 'D' or
earlier firmware, the SNMP-REPEATER-MIB is not
supported. These hubs map hub ports to interfaces
in the interfaces group of RFC1213-MIB. For these
hubs, the variable binding list contains
ifAdminStatus for the backup port on the hub
instead of rptrPortAdminStatus.
Backup links are not supported on the HP28688A
hub. TRAP-TYPE .1.3.6.1.4.1.11.2.14.2.0.5 |
intrusionTrapAn intrusionTrap(6) is device type specific to
EtherTwist hubs with revision 'E' firmware or
later and AdvanceStack hubs. It signifies that a
port security violation has been detected on a
port which has the hubSecPtAlarmEnable flag set
to 'enabled'. The MAC address of the intruder
and the port on which the intrusion occurred are
returned in the PDU. TRAP-TYPE .1.3.6.1.4.1.11.2.14.2.0.6 |
addressMovedTrapAn addressMovedTrap(7) is device type specific
to EtherTwist hubs with revision 'E' firmware or
later and AdvanceStack hubs. It signifies that a
source MAC address which had been operating at
one port has moved to a new port. The MAC
address that moved, the group and port that the
address moved from, and the group and port that
the address moved to are returned in the PDU. TRAP-TYPE .1.3.6.1.4.1.11.2.14.2.0.7 |
newAddressTrapA newAddressTrap(8) is device type specific to
EtherTwist hubs with revision 'E' firmware or
later and AdvanceStack hubs. It signifies that a
new MAC address has been detected on one of the
hub's ports. The instance of
rptrAddrTrackLastSourceAddress for the port with
the new address is returned in the PDU. TRAP-TYPE .1.3.6.1.4.1.11.2.14.2.0.8 |
hubThinlanFaultWhen set to 'true' this object causes the Fault
LED to blink if the ThinLan Port is segmented.
This object has been deprecated in favor of
hpRptrThinlanFault.rwobsolete INTEGER --{ -- false(0), -- true(1) --} .1.3.6.1.4.1.11.2.14.2.1 |
hubGlobal OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.2.2 |
hubGlobalErrorsThis counter is incremented for each packet with
an error received on any port. This counter does
not include runts, as they are a normal media
condition.
This object has been deprecated in favor of
hpRptrMonGlobalErrors.roobsolete Counter .1.3.6.1.4.1.11.2.14.2.2.1 |
hubGlobalCollisionsThis counter is incremented for each collision
between any two or more ports (or AUI) detected by
the hub.
This object has been deprecated in favor of
rptrMonitorTransmitCollisions.roobsolete Counter .1.3.6.1.4.1.11.2.14.2.2.2 |
hubGlobalPktFragmentsThis counter is the sum of hubPortPktFragments
for all ports.
This object has been deprecated in favor of
hpRptrMonGlobalFrames.roobsolete Counter .1.3.6.1.4.1.11.2.14.2.2.3 |
hubGlobalRuntsThis counter is incremented for each runt frame
received on any port.
This object has been deprecated in favor of
hpRptrMonGlobalRunts.roobsolete Counter .1.3.6.1.4.1.11.2.14.2.2.4 |
hubGlobalGiantsThis counter is incremented for each giant frame
received on any port.
This object has been deprecated in favor of
hpRptrMonGlobalFrameTooLongs.roobsolete Counter .1.3.6.1.4.1.11.2.14.2.2.5 |
hubGlobalCrcErrorsThis counter is incremented for each frame with a
CRC error received on any port.
This object has been deprecated in favor of
hpRptrMonGlobalFCSErrors.roobsolete Counter .1.3.6.1.4.1.11.2.14.2.2.6 |
hubGlobalAlignmentErrorsThis counter is incremented for each frame with
an alignment error received on any port.
This object has been deprecated in favor of
hpRptrMonGlobalAlignmentErrors.roobsolete Counter .1.3.6.1.4.1.11.2.14.2.2.7 |
hubGlobalInOctetsThis counter is incremented for each octet
received on any port.
This object has been deprecated in favor of
hpRptrMonGlobalOctets.roobsolete Counter .1.3.6.1.4.1.11.2.14.2.2.8 |
hubGlobalInUcastPktsThis counter is incremented for each unicast
packet received on any port.
This counter has been deprecated in favor of
hpRptrMonGlobalUcastPackets.roobsolete Counter .1.3.6.1.4.1.11.2.14.2.2.9 |
hubGlobalInNUcastPktsThis counter is incremented for each non-unicast
packet received on any port.
This object has been deprecated in favor of
hpRptrMonGlobalBcastPackets and
hpRptrMonGlobalMcastPackets.roobsolete Counter .1.3.6.1.4.1.11.2.14.2.2.10 |
hubGlobalInBroadcastPktsThis counter is incremented for each broadcast
packet received on any port.
This object has been deprecated in favor of
hpRptrMonGlobalBcastPackets.roobsolete Counter .1.3.6.1.4.1.11.2.14.2.2.11 |
hubPortTableA list of hubPort entries.obsolete SEQUENCE OF HubPortEntry .1.3.6.1.4.1.11.2.14.2.3 |
hubPortIndexThe index value which uniquely identifies the
port to which this entry is applicable. The port
identified by a particular value of this index is
the same port as identified by the same value of
rptrPortIndex.roobsolete INTEGER .1.3.6.1.4.1.11.2.14.2.3.1 |
hubPortPktFragmentsThis counter is incremented when a packet or
packet fragment is encountered for a port
instance.
This object has been deprecated in favor of
rptrMonitorPortReadableFrames.roobsolete Counter .1.3.6.1.4.1.11.2.14.2.3.2 |
hubPortCollisionsThis counter is incremented when a port is
involved in a collision.
This object has been deprecated in favor of
rptrMonitorPortCollisions.roobsolete Counter .1.3.6.1.4.1.11.2.14.2.3.3 |
hubPortSegmentationThis is a flag which is 'true' if the port is
currently segmented and 'false' otherwise.
This object has been deprecated in favor of
rptrPortAutoPartitionState.roobsolete INTEGER --{ -- false(0), -- true(1) --} .1.3.6.1.4.1.11.2.14.2.3.4 |
hubPortLinkBeatStatusThis is a flag which is 'true' if link beat is
detected on the port and 'false' otherwise. The
value of this variable will always be 'true' when
the corresponding instance of
hubPortLinkBeatEnable is 'false'.
This object has been deprecated in favor of
rpMauMediaAvailable.roobsolete INTEGER --{ -- false(0), -- true(1) --} .1.3.6.1.4.1.11.2.14.2.3.5 |
hubPortLinkBeatEnableWhen this flag is set to 'true' the port's link
beat is enabled and when set to 'false' it is
disabled.
This object has been deprecated in favor of
hpRptrPtLinkbeatEnable.rwobsolete INTEGER --{ -- false(0), -- true(1) --} .1.3.6.1.4.1.11.2.14.2.3.6 |
hubPortMacAddressEach port maintains the MAC address of the node
currently attached to it. This address is valid
only when the port state flag is set to
'psSingle'.
This object has been deprecated in favor of
rptrAddrTrackNewLastSrcAddress.roobsolete MacAddress (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.2.3.7 |
hubPortAddressStateThe port state object may take on three values.
'psNone' means no packets have been received on
the port. 'psSingle' means all packets received on
the port have originated from a single MAC
address. 'psMany' means that packets originating
from more than one node have been received on the
port. To (re)start a search for a MAC address set
the port state to 'psNone'.rwobsolete INTEGER --{ -- psNone(0), -- psSingle(1), -- psMany(2) --} .1.3.6.1.4.1.11.2.14.2.3.8 |
hubPortPolarityReversedThis object is used to indicate that the hub port
was wired with the positive/negative polarity of
its transmit and receive pairs reversed. Note
that the port will continue to operate in this
state, with the hub inverting the polarity
internally.
This object has been deprecated in favor of
hpRptrPtPolarityReversed.roobsolete INTEGER --{ -- false(0), -- true(1) --} .1.3.6.1.4.1.11.2.14.2.3.9 |
hubPortLateEventDisableThis object indicates that the hub port was
disabled as a result of excessive late collisions
being caused by the end node attached to this
port. This flag is cleared when the port is
reenabled by setting rptrPortAdminStatus to
'enabled'.roobsolete Enumeration .1.3.6.1.4.1.11.2.14.2.3.10 |
hubBitmaps OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.2.4 |
hubPortsOperStatusThe hubPortsOperStatus is a bit map of the state
of all hub ports. The object has a 1 bit for each
port that is enabled, not segmented, and linkbeat
is detected. Ports on which these conditions are
not true have a 0 bit. The bits are placed into
the OCTET STRING in the following order:
octet 0 octet 1 octet 2 ...
bits 7-0 bits 7-0 bits 7-0 ...
ports 1-8 ports 9-16 ports 17-24 ...
Values of unused bits in the last octet are
undefined.
This object has been deprecated in favor of
hpRptrGrpPortsAdminStatus.roobsolete OCTET STRING .1.3.6.1.4.1.11.2.14.2.4.1 |
hubAddressTableMaxAgeThe hubAddressTableMaxAge is the time beyond
which an inactive MAC address will be removed from
the hubPortMacAddress table and the
hubAddressTable. Although hubAddressTableMaxAge
is specified in units of 10ms time ticks, the
actual resolution of this timer is 10 seconds. A
value of 65535000 indicates no aging shall take
place.rwobsolete TimeTicks -- .1.3.6.1.4.1.11.2.14.2.5 |
hubAddressTableA list of entries present in the hub address
table.deprecated SEQUENCE OF HubAddressEntry .1.3.6.1.4.1.11.2.14.2.6 |
hubAddressIndexThe index value which uniquely identifies the
chunk to which this entry is applicable.roobsolete INTEGER .1.3.6.1.4.1.11.2.14.2.6.1 |
hubAddressChunkThe hubAddressChunk object returns an opaque
chunk of the address table. Each chunk can be
interpreted as an array of records in the form:
mac address [6 bytes], port number [2 bytes],
inactivity time [4 bytes]
On a Get, the returned chunk can include empty
(unused) entries. Instances are chunk numbers,
which start at 1 and go to 52. Each chunk can
hold 34 addresses.
A returned chunk might look like:
Address Port Inactivity Time
080009001234 1 0
080009002345 2 10000
080009003456 1 20000
000000000000 1 0
080009009876 EMPTY 0
080009004567 EMPTY 15000
.
.
.
080009005678 EOL 959000
A value of EMPTY in the Port field indicates an
unused (i.e. aged out) entry in the table. When
the EOL (End Of List) bit is set in the Port
field, that entry is the last entry in the table.
It is possible for EOL to be seen in any entry.
EOL (0x4000) and EMPTY (0x8000) are bit masks
which are ORed with the port number in the port
field of the entry. It is possible for both the
EOL and EMPTY bits to be set in the same entry.
The remainder of the chunk after the EOL entry
will be zeroed.
The inactivityTime and Address fields are
meaningless if the EMPTY bit is set in the Port
field. In this case, inactivityTime and Address
are not guaranteed to be zeroed. The Manager may
start with any chunk it likes and request the
chunks in any order. It may perform multiple
requests for the same chunk. The agent does not
save state from previous requests.
A request of chunk #1 would return the contents of
the first 34 address table entries, whether they
are all full, all empty, or some full and the rest
empty. A request of chunk #2 will return entries
#35 through #68. And so on.
The address table can change between Get requests.
An address' location can change, or an address
could age out and then be added back in at a
different location in the table. Thus, the
Manager could see the address twice in the table.roobsolete OCTET STRING .1.3.6.1.4.1.11.2.14.2.6.2 |
hubNumBkpLinksThe number of backup links configurable on this
hub.roobsolete INTEGER .1.3.6.1.4.1.11.2.14.2.7 |
hubBkpLinkTableA list of backup link configuration entries. For
a given backup link, the hub will periodically
send a test packet to the device at the end of the
link. If there are no responses (the number is
configurable), the hub will enable the backup port
and disable the primary port. After the primary
link is fixed, the user must turn the primary port
on to resume normal operation.
At any time, the management station can look at
rptrPortAdminStatus for the backup port to
determine if it is currently in use.
The backup link algorithm enables and disables the
backup port by modifying rptrPortAdminStatus for
that port. After the backup port has been enabled
by the backup link algorithm, if the primary port
is subsequently enabled via the hub console port
or by a set of rptrPortAdminStatus, the backup
port will be turned off and the periodic test
packets will begin again.
When the backup link objects are set, the backup
port will be turned off, the primary port will be
turned on, and the periodic test packets will be
sent. The time between test packets is
configurable by setting hubBackupTestTime. The
number of failures needed to switch to the backup
link is configured by setting
hubBackupConsecutiveFails. The backup link
function can be turned off by setting
hubBackupPort to 0.
All five of the backup link objects must be set
together in a single PDU except for the case of
setting hubBackupPort to 0, in which case, the
hubBackupPort can be set without setting the other
objects. Currently, the size of the backup link
table is one; future releases may provide the
ability to monitor more than one backup link.obsolete SEQUENCE OF HubBkpLinkEntry .1.3.6.1.4.1.11.2.14.2.8 |
hubBkpLinkIndexThe index value which uniquely identifies the
backup link configuration entry to which the
instance is applicable.roobsolete INTEGER .1.3.6.1.4.1.11.2.14.2.8.1 |
hubBackupPortThe port number of the backup link. Setting this
object to zero removes the backup link
configuration.rwobsolete INTEGER .1.3.6.1.4.1.11.2.14.2.8.2 |
hubPrimaryPortThe port number of the primary link. It can only
be set to zero if the hubBackupPort is also zero.rwobsolete INTEGER .1.3.6.1.4.1.11.2.14.2.8.3 |
hubBackupAddressThe MAC address of the device at the other end of
the primary link which will respond to the
periodic test packets sent by this hub.rwobsolete OCTET STRING .1.3.6.1.4.1.11.2.14.2.8.4 |
hubBackupTestTimeThe frequency, in time ticks, between sending the
periodic test packets. The actual resolution of
this timer is in seconds. The test packet
response timeout is fixed at 500ms.rwobsolete TimeTicks -- .1.3.6.1.4.1.11.2.14.2.8.5 |
hubBackupConsecutiveFailsThe number of test packet failures which will
cause the hub to switch to the backup link (i.e.,
backup port turned on, primary port turned off).
A value of one is generally not recomended and
will cause the backup link to be enabled upon the
first failure.rwobsolete INTEGER .1.3.6.1.4.1.11.2.14.2.8.6 |
hubSqeEnabledWhen 'true', this flag indicates that SQE has
been detected for the last ten agent transmits and
there is a high probability that the SQE switch on
the transceiver attached to the AUI port is set to
Enabled, when it should be Disabled.
This object has been deprecated in favor of
hpRptrSqeEnabled.roobsolete INTEGER --{ -- false(0), -- true(1) --} .1.3.6.1.4.1.11.2.14.2.9 |
hubSecurity OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.2.10 |
hubSecurePortTableTable containing security configuration for each
port. SEQUENCE OF HubSecurePortEntry .1.3.6.1.4.1.11.2.14.2.10.1 |
hubSecurePortEntryAn entry in the hubSecurePortTable, containing
the security configuration for a single port. HubSecurePortEntry .1.3.6.1.4.1.11.2.14.2.10.1.1 |
hubSecPtGroupIndexThis object identifies the group containing the
port for which this entry contains security
configuration information.ro INTEGER .1.3.6.1.4.1.11.2.14.2.10.1.1.1 |
hubSecPtPortIndexThis object identifies the port within the group
for which this entry contains security
configuration information.ro INTEGER .1.3.6.1.4.1.11.2.14.2.10.1.1.2 |
hubSecPtSecurityAddressThe desired authorized MAC address for this port.
This can be either a regular station address to
configure a specific address, or it can be one of
the following special values to specify the
address learning method:
FFFF-FFFF-FFFE: learnOnce. First source MAC
address heard on this port becomes the
authorized address. Setting this value
initiates learning of a new authorized
address. When a new authorized address is
learned, it will be stored in nonvolatile
memory. This variable will return
learnOnceConditionally to a GET operation
after it has been set to this value.
FFFF-FFFF-FFFD: learnOnceConditionally. This
option will initiate learning of a new
authorized address only if the previous
hubSecPtSecurityAddress was set to a
specific address or learnContinuous. No
action will be performed if the previous
value was already learnOnceConditionally.
FFFF-FFFF-FFFC: learnContinuous. Any address
heard becomes the new authorized address.
When a new address is learned, it may
cause an alarm, but it does not store
anything in nonvolatile memory.rw OCTET STRING .1.3.6.1.4.1.11.2.14.2.10.1.1.3 |
hubSecPtAuthorizedAddressThe MAC address of the station authorized to be
on this port. This address could either have been
configured by specifying a regular station address
for hubSecPtSecurityAddress, or it could have been
learned by the agent if hubSecPtSecurityAddress
was set to one of the special values listed above.
Once the agent has learned an authorized address,
it will be saved across powerfails, unless the
agent was configured for learnContinuous mode.ro OCTET STRING .1.3.6.1.4.1.11.2.14.2.10.1.1.4 |
hubSecPtPreventEavesdropIf enabled, unicast packets not addressed to the
authorized address for this port will be
scrambled.rw Enumeration .1.3.6.1.4.1.11.2.14.2.10.1.1.5 |
hubSecPtAlarmEnableIf enabled, the agent will generate an
intrusionTrap if a packet is received on this port
with a source MAC address that is different from
the hubSecPtAuthorizedAddress for this port.rw Enumeration .1.3.6.1.4.1.11.2.14.2.10.1.1.6 |
hubSecPtIntrusionFlagThis flag indicates if an intrusion has occurred
on this port. The Security LED on the hub will
blink if any instance of this flag has the value
intrusion. Setting this flag to noIntrusion will
turn off the Security LED if no other ports have
this flag set to intrusion. An intrusion will
only cause an alarm and an intrusion log entry if
this flag is equal to noIntrusion.rw Enumeration .1.3.6.1.4.1.11.2.14.2.10.1.1.7 |
hubIntruderLogTableThis table contains a record of the twenty most
recent port security violations. The first entry
in the table is the oldest. SEQUENCE OF HubIntruderLogEntry .1.3.6.1.4.1.11.2.14.2.10.2 |
hubIntruderLogEntryA row in the hubIntruderLogTable containing
information about a single port security
violation. HubIntruderLogEntry .1.3.6.1.4.1.11.2.14.2.10.2.1 |
hubIntruderIndexThe index of this entry in the intruder log
table. Index 1 will always contain the oldest
entry. If the table is full when a new intrusion
occurs, the new entry becomes index 20, and all
earlier entries are shifted down by one entry,
removing the old index 1.ro INTEGER .1.3.6.1.4.1.11.2.14.2.10.2.1.1 |
hubIntruderGroupThis object identifies the group containing the
port on which this intrusion occurred.ro INTEGER .1.3.6.1.4.1.11.2.14.2.10.2.1.2 |
hubIntruderPortThis object identifies the port within the group
on which this intrusion occurred. A port number
of zero indicates that this entry is unused and
the values for the other variables in this entry
are undefined.ro INTEGER .1.3.6.1.4.1.11.2.14.2.10.2.1.3 |
hubIntruderAddressThis object contains the source MAC address of
the intruder.ro OCTET STRING .1.3.6.1.4.1.11.2.14.2.10.2.1.4 |
hubIntruderTimeThe value of sysUpTime when the intrusion
occurred. This will be zero if the agent has been
reset since the intruder was detected, since
sysUpTime could be misinterpreted in that case.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.11.2.14.2.10.2.1.5 |
hubAddressMoveLogTableA log of the 20 most recent times that the agent
detected that a source MAC address which had been
heard on one port had moved to a different port. SEQUENCE OF HubAddressMoveLogEntry .1.3.6.1.4.1.11.2.14.2.11 |
hubAddressMoveLogEntryA row in the hubAddressMoveLogTable containing
information about a single address movement. HubAddressMoveLogEntry .1.3.6.1.4.1.11.2.14.2.11.1 |
hubAddrMoveIndexThe index of this entry in the address movement
log table. Index 1 will always contain the oldest
entry. If the table is full when a new address
movement occurs, the new entry becomes index 20,
and all earlier entries are shifted down by one
entry, removing the old index 1.ro INTEGER .1.3.6.1.4.1.11.2.14.2.11.1.1 |
hubAddrMoveAddressThe MAC address of the station that moved to a
new port.ro OCTET STRING .1.3.6.1.4.1.11.2.14.2.11.1.2 |
hubAddrMoveOldGroupThe group containing the port on which this
address had been operating before it moved.ro INTEGER .1.3.6.1.4.1.11.2.14.2.11.1.3 |
hubAddrMoveOldPortThe port within the group on which this address
had been operating before it moved.ro INTEGER .1.3.6.1.4.1.11.2.14.2.11.1.4 |
hubAddrMoveNewGroupThe group containing the port that the address
moved to.ro INTEGER .1.3.6.1.4.1.11.2.14.2.11.1.5 |
hubAddrMoveNewPortThe port within the group that the address moved
to.ro INTEGER .1.3.6.1.4.1.11.2.14.2.11.1.6 |
hubLateEventMonitorThis object configures the late event monitoring
functionality for the hub. This mode periodically
samples the rptrMonitorPortLateEvents value for
each port. If the agent detects excessive late
events on a port, the port will be disabled by
setting the rptrPortAdminStatus for that port to
'disabled', and the hubPortLateEventDisable flag
for that port will be set to 'true'. This mode is
'off' by default. Setting it to 'onSingle'
enables the mode for all non-cascaded hub ports.
Setting it to 'onAll' enables the mode for all hub
ports, including cascaded ports.rw Enumeration .1.3.6.1.4.1.11.2.14.2.12 |
icfBridge OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.3 |
stpTrapA stpTrap(3) is device type specific to ICF
bridges. It signifies that the Spanning Tree
entity in the bridge has detected a change of
state to either Blocking or Forwarding. TRAP-TYPE .1.3.6.1.4.1.11.2.14.3.0.3 |
temperatureTrapA temperatureTrap(4) is device type specific to
ICF bridges. It signifies that the bridge hardware
has detected an overheated condition. TRAP-TYPE .1.3.6.1.4.1.11.2.14.3.0.4 |
operationalStateThis object controls the forwarding nature of the
bridge. In the Learning state the bridge will
learn new MAC addresses, and it ages out older MAC
addresses. Statically configured addresses are
discarded (they do not age). In the Secure state,
the bridge will not learn new MAC addresses.
Statically configured addresses are forwarded
(they do not age).rwobsolete INTEGER --{ -- learning(0), -- secure(1) --} .1.3.6.1.4.1.11.2.14.3.1 |
forwardDbMaxAgeThe value of this object controls how long a MAC
address stays in the forwarding database. See
802.1d, section 3.9.2 'Dynamic Entries'.rwobsolete TimeTicks -- .1.3.6.1.4.1.11.2.14.3.2 |
addressTableA list of address entries.obsolete SEQUENCE OF AddressEntry .1.3.6.1.4.1.11.2.14.3.3 |
addressIndexThe index value which uniquely identifies the
chunk to which this entry is applicable.roobsolete INTEGER .1.3.6.1.4.1.11.2.14.3.3.1 |
addressChunkThis object returns an opaque chunk of the
address table. The instance specifies a chunk of
the address table. Each chunk can be interpreted
as an array of 41 records of the form:
{ macAddress[6bytes], port number[2bytes],
permanence[2bytes] }.
Address Port Perm
00 080009001234 1 Dynamic(0x0000)
01 080009002345 2 Dynamic(0x0000)
02 000000000000 EMPTY(0x8000) Dynamic(0x0000)
03 080009003456 1 Dynamic(0x0000)
04 000000000000 1 Dynamic(0x0000)
05 080009009876 EMPTY(0x8000) Dynamic(0x0000)
06 080009004567 EMPTY(0x8000) Static(0x0008)
07 080009041d08
... ... ...
40 080009005678 EOL(0x4000) Permanent(0x0000)
A value of EMPTY in the Port field indicates an
aged out table entry. A value of EOL in the Port
field indicates that it is the last entry in the
table. Of course, EOL will only be seen in the
last entry. EOL and EMPTY are AND-able bit
fields. The Disposition and Address are
meaningless if Port is EMPTY.
When instance=1 is used on a Set, the agent clears
the table prior to setting any addresses. On
subsequent Sets, the agent adds the specified
addresses. If a Set starts at instance > 1, the
specified addresses will be added to the table
without first clearing the table. Addresses are
already in the table are deleted and then
readded.rwobsolete OCTET STRING .1.3.6.1.4.1.11.2.14.3.3.2 |
brgPortTableA list of brgPort entries.obsolete SEQUENCE OF BrgPortEntry .1.3.6.1.4.1.11.2.14.3.4 |
brgPortIndexThe index value which uniquely identifies the
interface/port to which this entry is applicable.
The interface/port identified by a particular
value of this index is the same interface/port as
identified by the same value of ifIndex.roobsolete INTEGER .1.3.6.1.4.1.11.2.14.3.4.1 |
brgPortCacheHitsCount of the successful cache matches when
looking up a destination MAC address.roobsolete Counter .1.3.6.1.4.1.11.2.14.3.4.2 |
brgPortCacheMissesCount of the unsuccessful cache matches when
looking up a destination MAC address.roobsolete Counter .1.3.6.1.4.1.11.2.14.3.4.3 |
brgPortForwardedPktsCount of the packets received on this port and
forwarded to the other port.roobsolete Counter .1.3.6.1.4.1.11.2.14.3.4.4 |
brgPortFilteredPktsCount of the frames that were received on this
port and filtered.roobsolete Counter .1.3.6.1.4.1.11.2.14.3.4.5 |
wildcardTableA list of wildcard entries.obsolete SEQUENCE OF WildcardEntry .1.3.6.1.4.1.11.2.14.3.5 |
wildcardIndexThe index value which uniquely identifies the
interface/port to which this entry is applicable.
The interface/port identified by a particular
value of this index is the same interface/port as
identified by the same value of ifIndex.roobsolete INTEGER .1.3.6.1.4.1.11.2.14.3.5.1 |
wildcardFilterThis object contains the binary value used to
filter frames. The data in the frame at the offset
specified by the Wildcard offsets is XOR'ed with
this object after AND'ing with the Wildcard Mask.
If zero result occurs, the packet is discarded
(filtered).
Suppose the user specifies the following values:
data: 11001010 10101010 10101010 10101010
mask: 11100000 00000000 00000000 00000000
filter: 11100000 00000000 00000000 00000000
AND'ing data with the mask gives:
11000000 00000000 00000000 00000000
XOR'ing that value with the filter gives:
00100000 00000000 00000000 00000000
The non-zero result indicates no match (don't
discard).
Another example:
data: 10011010 10101010 10101010 10101010
mask: 10010000 00000000 00000000 00000000
filter: 10010000 00000000 00000000 00000000
AND'ing data with the mask gives:
10010000 00000000 00000000 00000000
XOR'ing that value with the filter gives:
00000000 00000000 00000000 00000000
A zero result indicates a match, so we discard
(filter) the packet.
The filter AND'ed with the mask must equal the
filter. This is an example of a legal filter/mask
pair:
filter: 00010000 00000000 00000000 00000000
mask: 10010000 00000000 00000000 00000000
AND'ed: 00010000 00000000 00000000 00000000
(equals filter)
Another way of saying this: if a mask bit is zero,
the corresponding filter bit must be zero.
The following would be an illegal pair:
filter: 01110000 00000000 00000000 00000000
mask: 10010000 00000000 00000000 00000000
AND'ed: 00010000 00000000 00000000 00000000
( != filter)rwobsolete OCTET STRING .1.3.6.1.4.1.11.2.14.3.5.2 |
wildcardMaskThis object indicates which portion of the
wildcardFilter is to be used in filtering. The
data in the frame at the offset specified by
Wildcard offsets is AND'ed with this object. The
result is XOR'ed with the Wildcard Filter object.
If a zero result is obtained, the packet is
discarded.
If an all-zeros wildcardMask is specified, a
genErr is returned. Also, see mask/filter
constraints in the description of the
wildcardFilter object.rwobsolete OCTET STRING .1.3.6.1.4.1.11.2.14.3.5.3 |
wildcardOffsetIndicates the position in a received frame which
is to have the Wildcard Mask/Filter applied. The
indicated packet byte is aligned with the 0th byte
of the wildcard mask/filter held in network byte
order.
The MAC destination address starts at byte
position (wildcardOffset) zero.
The wildcardOffset must fall on a 2-byte boundary,
0,2,4,...,1512 (violations of this constraint
result in a genErr). Filters can be aligned on
non 2-byte boundaries through use of the
wildcardUserOffset.rwobsolete INTEGER .1.3.6.1.4.1.11.2.14.3.5.4 |
wildcardUserOffsetThis value is a byte offset from the beginning
of the packet. If this offset is such that any
portion of the filter extends past the end of the
packet (for wildcard filtering purposes, the FCS
is part of the packet), then the filter is
considered not to match, and the packet is not
filtered.
For a particular filter, the wildcardUserOffset
must be greater than or equal to the
wildcardOffset.
wildcardUserOffset must be between 0 and 1514,
inclusive.
The wildcardUserOffset, wildcardOffset pair must
conform to one of the following four relationships
and also be subject to the range restrictions
listed above. For n = 0,..,378
Offset 4n 4n 4n 4n+2
UserOffset 4n 4n+1 4n+2 4n+3
As an example, consider four examples in the
following table for locating the filter at or near
the beginning of a packet:
- 6 filter/mask bytes - - desired -
0 1 2 3 4 5 6 - position -
A|f/m0 f/m1 f/m2 f/m3 00 00 00 |0,4,8,12,...
B| 00 f/m0 f/m1 f/m2 f/m3 00 00 |1,5,9,13,...
C| 00 00 f/m0 f/m1 f/m2 f/m3 00 |2,6,10,14,...
D| 00 00 00 f/m0 f/m1 f/m2 f/m3|3,7,11,15,...
Example A corresponds to a UserOffset/Offset pair
such as 0/0 (4n/4n). Example B represents a pair
such as 0/1 (4n/4n+1). Example C is 0/2
(4n/4n+2). Finally, example D is 2/3 (4n+2/4n+3).
If any of the above constraints is not honored,
the SET Response will indicate genErr.rwobsolete INTEGER .1.3.6.1.4.1.11.2.14.3.5.5 |
wildcardArmThis object arms (enables) the Wildcard Filter
provided all of the other wildcard objects have
been set to proper values. To disarm a wildcard,
only the wildcardArm object need be set.rwobsolete INTEGER --{ -- off(0), -- on(1) --} .1.3.6.1.4.1.11.2.14.3.5.6 |
stp OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.3.6 |
stpBridgeIdA 64 bit binary bridge id composed of bridge
priority and the bridge's mac address fields. see:
IEEE 802.1(d) 6.8.1.1.3(1), 4.5.3.7roobsolete OCTET STRING .1.3.6.1.4.1.11.2.14.3.6.1 |
stpTopoChangeTimeThe time since the last topology change. see:
IEEE 802.1(d) 6.8.1.1.3(2), 4.5.3.12roobsolete TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.11.2.14.3.6.2 |
stpTopoNumChangesThe number of topo changes since initialization
of STP. see: IEEE 802.1(d) 6.8.1.1.3(3)roobsolete Counter .1.3.6.1.4.1.11.2.14.3.6.3 |
stpTopoChangeA 1 bit flag broadcast by the root bridge
indicating that a topology change is underway, and
Stp bridges should use short term aging. see: IEEE
802.1(d) 6.8.1.1.3(4), 4.5.3.12roobsolete INTEGER --{ -- false(0), -- true(1) --} .1.3.6.1.4.1.11.2.14.3.6.4 |
stpDesignatedRootThe binary bridge id that this bridge believes to
be the root bridge for the bridged Lan. see: IEEE
802.1(d) 6.8.1.1.3(5), 4.5.3.1roobsolete OCTET STRING .1.3.6.1.4.1.11.2.14.3.6.5 |
stpRootCostThe cost of the path to the root bridge from this
bridge; equal to the sum of the designated cost
and the path cost held for the root port. see:
IEEE 802.1(d) 6.8.1.1.3(6), 4.5.3.2roobsolete INTEGER .1.3.6.1.4.1.11.2.14.3.6.6 |
stpRootPortThe port id that this bridge believes to be the
root bridge's root port for the bridged Lan. see:
IEEE 802.1(d) 6.8.1.1.3(7), 4.5.3.3roobsolete INTEGER .1.3.6.1.4.1.11.2.14.3.6.7 |
stpCurrentMaxAgeThe Max Age value received from the Root Bridge
(in seconds); the Stp is currently using the
value. see: IEEE 802.1(d) 6.8.1.1.3(8), 4.5.3.4roobsolete INTEGER .1.3.6.1.4.1.11.2.14.3.6.8 |
stpCurrentHelloTimeThe Hello time value received from the Root
Bridge (in seconds); the Stp records the value.
see: IEEE 802.1(d) 6.8.1.1.3(9), 4.5.3.5roobsolete INTEGER .1.3.6.1.4.1.11.2.14.3.6.9 |
stpCurrentForwardDelayThe forward delay value received from the Root
Bridge (in seconds); the Stp is currently using
the value. see: IEEE 802.1(d) 6.8.1.1.3(10),
4.5.3.6roobsolete INTEGER .1.3.6.1.4.1.11.2.14.3.6.10 |
stpMaxAgeThe maximum age allowed of Config information for
a port before a bridge will attempt to become the
root (in seconds). Transmitted by this bridge when
it is, or is attempting to become the root. see:
IEEE 802.1(d) 6.8.1.1.3(11), 6.8.1.2.2(1),
4.5.3.8rwobsolete INTEGER .1.3.6.1.4.1.11.2.14.3.6.11 |
stpHelloTimeThe time between Config packet transmission when
this bridge is, or is attempting to become the
root (in seconds). Transmitted by this bridge when
it is, or is attempting to become the root. see:
IEEE 802.1(d) 6.8.1.1.3(12), 6.8.1.2.2(2),
4.5.3.9rwobsolete INTEGER .1.3.6.1.4.1.11.2.14.3.6.12 |
stpForwardDelayThe time spent in the Listening and Learning
states used when this bridge is, or is attempting
to become the root (in seconds). Transmitted by
this bridge when it is, or is attempting to become
the root. see: IEEE 802.1(d) 6.8.1.1.3(13),
6.8.1.2.2(3), 4.5.3.10rwobsolete INTEGER .1.3.6.1.4.1.11.2.14.3.6.13 |
stpPriorityThe upper 16 bits of the 64 bit BridgeId composed
of priority and the bridge's mac address fields.
see: IEEE 802.1(d) 6.8.1.2.2(4), 4.5.3.7rwobsolete INTEGER .1.3.6.1.4.1.11.2.14.3.6.14 |
stpPortTableA list of stpPort entries.obsolete SEQUENCE OF StpPortEntry .1.3.6.1.4.1.11.2.14.3.6.15 |
stpPortIndexThe index value which uniquely identifies the
port to which this entry is applicable. The port
identified by a particular value of this index is
the same interface/port as identified by the same
value of ifIndex. Not an IEEE 802.1(d) reqmt.roobsolete INTEGER .1.3.6.1.4.1.11.2.14.3.6.15.1 |
stpPortStateThe state of a port on a 2 port bridge is really
the state of the bridge itself. Management is only
allowed to set this object to 'stpDisabled' or
'stpBlocking'. Setting the object to 'stpDisabled'
will turn off spanning tree only if the state is
not 'stpBlocking' (to prevent loops). Setting the
object to 'stpBlocking' will turn on spanning tree
only if it was previously disabled. see: IEEE
802.1(d) 6.8.2.1.3(2), 4.4, 4.5.5.2rwobsolete INTEGER --{ -- stpDisabled(0), - settable -- stpListening(1), -- stpLearning(2), -- stpForwarding(3), -- stpBlocking(4) - settable --} .1.3.6.1.4.1.11.2.14.3.6.15.2 |
stpPortIdThe 16 bit port id composed of priority and the
port's unique id fields. see: IEEE 802.1(d)
6.8.2.1.3(3), 4.5.5.1roobsolete INTEGER .1.3.6.1.4.1.11.2.14.3.6.15.3 |
stpPortPathCostThe contribution of the path through this port,
when the port is the root port, to the total cost
of the path to the root for this bridge. see: IEEE
802.1(d) 6.8.2.1.3(4), 6.8.2.3.2(2), 4.5.5.3rwobsolete INTEGER .1.3.6.1.4.1.11.2.14.3.6.15.4 |
stpPortRootIdThe bridge id that this port believes to be the
root bridge for the bridged Lan. see: IEEE
802.1(d) 6.8.2.1.3(5), 4.5.5.4roobsolete OCTET STRING .1.3.6.1.4.1.11.2.14.3.6.15.5 |
stpPortDesignatedCostThe cost of the path to the root offered by the
Designated Port on the LAN to which this Port is
attached. see: IEEE 802.1(d) 6.8.2.1.3(6),
4.5.5.5roobsolete INTEGER .1.3.6.1.4.1.11.2.14.3.6.15.6 |
stpPortDesignatedBridgeThe Bridge Id of the designated bridge for the
LAN associated with the port. see: IEEE 802.1(d)
6.8.2.1.3(7), 4.5.5.6roobsolete OCTET STRING .1.3.6.1.4.1.11.2.14.3.6.15.7 |
stpPortDesignatedPortThe port id of the bridge believed to be the
designated port of the LAN associated with the
port. see: IEEE 802.1(d) 6.8.2.1.3(8), 4.5.5.7roobsolete INTEGER .1.3.6.1.4.1.11.2.14.3.6.15.8 |
stpPortPriorityThe upper 8 bits of the 16 bit PortId composed of
priority and the port's unique id fields. see:
IEEE 802.1(d) 6.8.2.3.2(3), 4.5.5.1rwobsolete INTEGER .1.3.6.1.4.1.11.2.14.3.6.15.9 |
hdlcErrorTableA list of hdlcError entries.obsolete SEQUENCE OF HdlcErrorEntry .1.3.6.1.4.1.11.2.14.3.7 |
hdlcErrorIndexThe index value which uniquely identifies the
port to which this entry is applicable. The port
identified by a particular value of this index is
the same interface/port as identified by the same
value of ifIndex. IcfBridge.HP28674: There is only
one 'real' instance of this object on port 2.roobsolete INTEGER .1.3.6.1.4.1.11.2.14.3.7.1 |
hdlcErrorIndicationsErrors occurring during information transfer
which required instruction from CPU for recovery.
This is a serious link problem. The local node
will either reset or disconnect after receiving
this message.roobsolete Counter .1.3.6.1.4.1.11.2.14.3.7.2 |
hdlcT1TimeoutsThe number of times the retransmission timer
(x25T1Timer) timed out.roobsolete Counter .1.3.6.1.4.1.11.2.14.3.7.3 |
hdlcMissedPacketsCount of the frames lost by the receiver because
there wasn't a receive buffer.roobsolete Counter .1.3.6.1.4.1.11.2.14.3.7.4 |
hdlcRcvOverrunsCount of the number of times the reciever's FIFO
was full when the receiver was ready to put new
data into the FIFO.roobsolete Counter .1.3.6.1.4.1.11.2.14.3.7.5 |
hdlcXmtUnderrunsCount of the number of times the transmitter has
aborted a frame transmission because data was
late from memory.roobsolete Counter .1.3.6.1.4.1.11.2.14.3.7.6 |
hdlcProviderLostPrimitivesCount of the number of lost control frames due to
802.3 priority processing on receive.roobsolete Counter .1.3.6.1.4.1.11.2.14.3.7.7 |
hdlcRuntFrameReceivesCount of the HDLC frames received that were less
than the minimum legal HDLC size.roobsolete Counter .1.3.6.1.4.1.11.2.14.3.7.8 |
hdlcGiantFrameReceivesCount of the HDLC frames received that were
larger than the maximum legal size that can be
sent on the 802.3 LAN link.roobsolete Counter .1.3.6.1.4.1.11.2.14.3.7.9 |
hdlcBadFrameReceivesCount of the sum of: HDLC frames with bad
checksum, and misaligned HDLC frames.roobsolete Counter .1.3.6.1.4.1.11.2.14.3.7.10 |
hdlcRejectFrameReceivesCount of the HDLC reject frames received.roobsolete Counter .1.3.6.1.4.1.11.2.14.3.7.11 |
hdlcRejectFrameSendsCount of the HDLC reject frames sent.roobsolete Counter .1.3.6.1.4.1.11.2.14.3.7.12 |
hdlcFrameRejectFrameRecsCount of the HDLC frame reject frames (FRMR)
received.roobsolete Counter .1.3.6.1.4.1.11.2.14.3.7.13 |
hdlcLocalTableA list of hdlcLocal entries.obsolete SEQUENCE OF HdlcLocalEntry .1.3.6.1.4.1.11.2.14.3.8 |
hdlcLocalIndexIndex into Hdlc local statistics table on a per
port basis. bridge.HP28674: There is only one
'real' instance of this object on port 2.roobsolete INTEGER .1.3.6.1.4.1.11.2.14.3.8.1 |
hdlcLocalResetRequestsCount of local HDLC requests to reset current
logical link.roobsolete Counter .1.3.6.1.4.1.11.2.14.3.8.2 |
hdlcLocalResetConfirmsCount of local HDLC node link reset
confirmations.roobsolete Counter .1.3.6.1.4.1.11.2.14.3.8.3 |
hdlcLocalConnectRequestsCount of local HDLC node attempts to establish
logical link.roobsolete Counter .1.3.6.1.4.1.11.2.14.3.8.4 |
hdlcLocalConnectConfirmsCount of local HDLC node connect request
acceptances.roobsolete Counter .1.3.6.1.4.1.11.2.14.3.8.5 |
hdlcLocalDisconnectRequestsCount of local HDLC node disconnect requests.roobsolete Counter .1.3.6.1.4.1.11.2.14.3.8.6 |
hdlcLocalDisconnectConfirmsCount of local HDLC node disconnects granted.roobsolete Counter .1.3.6.1.4.1.11.2.14.3.8.7 |
hdlcLocalStateCurrent local HDLC operational state.roobsolete INTEGER --{ -- t1HdlcStateNormal(0), -- t1HdlcStateBusy(1), -- t1HdlcStateRejectSent(2), -- t1HdlcStateDiscSent(3), -- t1HdlcStateDisconnect(4), -- t1HdlcStateConnSent(5), -- t1HdlcStateFrameRejectSent(6), -- t1HdlcStateResetSent(7), -- t1HdlcStateErrorIndication(8) --} .1.3.6.1.4.1.11.2.14.3.8.8 |
hdlcLocalAddressThe local HDLC address during communication with
the remote node. This object is valid only if a
brouter is on the remote end of the HDLC link. It
can only be set to one of the two values:
'hdlcDTEAddress' or 'hdlcDTEAddress'. Furthermore,
the setting of this object must be different from
the setting of the hdlcRemoteHdlcAddress object.
This object, along with hdlcRemoteAddress and
hdlcRemoteNodeId, constitute a superobject. See
hdlcRemoteNodeId for more details.rwobsolete Enumeration .1.3.6.1.4.1.11.2.14.3.8.9 |
hdlcLocalPhaseCurrent HDLC operational phase.roobsolete INTEGER --{ -- t1PhaseStopped(-1), -- t1PhaseInfo(0), -- t1PhaseDisconnect(1), -- t1PhaseReset(2), -- t1PhaseTransparentData(3) --} .1.3.6.1.4.1.11.2.14.3.8.10 |
hdlcRemoteTableA list of hdlcRemote entries.obsolete SEQUENCE OF HdlcRemoteEntry .1.3.6.1.4.1.11.2.14.3.9 |
hdlcRemoteIndexIndex into Hdlc remote statistics table on a per
port basis. bridge.HP28674: There is only one
'real' instance of this object on port 2.roobsolete INTEGER .1.3.6.1.4.1.11.2.14.3.9.1 |
hdlcRemoteResetRequestsCount of remote HDLC requests to reset current
logical link.roobsolete Counter .1.3.6.1.4.1.11.2.14.3.9.2 |
hdlcRemoteResetConfirmsCount of remote HDLC node link reset
confirmations.roobsolete Counter .1.3.6.1.4.1.11.2.14.3.9.3 |
hdlcRemoteConnectRequestsCount of remote HDLC node attempts to establish
logical link.roobsolete Counter .1.3.6.1.4.1.11.2.14.3.9.4 |
hdlcRemoteConnectConfirmsCount of remote HDLC node connect request
acceptances.roobsolete Counter .1.3.6.1.4.1.11.2.14.3.9.5 |
hdlcRemoteDisconnectRequestsCount of remote HDLC node disconnect requests.roobsolete Counter .1.3.6.1.4.1.11.2.14.3.9.6 |
hdlcRemoteStateCurrent remote HDLC operational state.roobsolete INTEGER --{ -- t1HdlcStateNormal(0), -- t1HdlcStateBusy(1), -- t1HdlcStateRejectSent(2), -- t1HdlcStateDiscSent(3), -- t1HdlcStateDisconnect(4), -- t1HdlcStateConnSent(5), -- t1HdlcStateFrameRejectSent(6), -- t1HdlcStateResetSent(7), -- t1HdlcStateErrorIndication(8) --} .1.3.6.1.4.1.11.2.14.3.9.7 |
hdlcRemoteAddressThe remote HDLC address during communication with
the local node. This object is valid only if a
brouter is on the remote end of the HDLC link. It
can only be set to one of the two values:
'hdlcDCEAddress' or 'hdlcDTEAddress'. Furthermore,
the setting of this object must be different from
the setting of the hdlcLocalAddress object. This
object, along with hdlcLocalAddress and
hdlcRemoteNodeId, constitute a superobject. See
hdlcRemoteNodeId for more details.rwobsolete Enumeration .1.3.6.1.4.1.11.2.14.3.9.8 |
hdlcRemoteXidCommandsCount of XID commands issued by remote node.roobsolete Counter .1.3.6.1.4.1.11.2.14.3.9.9 |
hdlcRemoteXidResponsesCount of XID responses issued by remote node.roobsolete Counter .1.3.6.1.4.1.11.2.14.3.9.10 |
hdlcRemoteTestCommandsCount of Test commands issued by remote node.roobsolete Counter .1.3.6.1.4.1.11.2.14.3.9.11 |
hdlcRemoteTestResponsesCount of Test responses issued by remote node.roobsolete Counter .1.3.6.1.4.1.11.2.14.3.9.12 |
hdlcRemoteNodeIdIdentification of the node at the opposite end of
the HDLC link (eg. brouter or bridge). This
object, along with hdlcLocalAddress and
hdlcRemoteAddress, constitute a superobject. This
object may only be set to one of the two values:
'remoteNodeBridge' or 'remoteNodeRouter'. If this
object is set to 'remoteNodeUnknown', then
hdlcLocalAddress and hdlcRemoteAddress need not be
supplied, and will be ignored if provided. In a
get, this object may report 'remoteNodeBridge',
but attempts to set this object to
'remoteNodeBridge' will result in an error pdu
with error type invalidData. If this object is set
to 'remoteNodeRouter', then hdlcLocalAddress and
hdlcRemoteAddress must be present and contiguous
in the pdu in order to properly complete the
superobject. The three objects may be in any order
within the pdu.rwobsolete INTEGER --{ -- remoteNodeBridge(0), -- remoteNodeRouter(1), - Settable -- remoteNodeUnknown(2) - Settable --} .1.3.6.1.4.1.11.2.14.3.9.13 |
x25TableA list of X25 entries.obsolete SEQUENCE OF X25Entry .1.3.6.1.4.1.11.2.14.3.10 |
x25IndexIndex into X25 remote timer table on a per port
basis. bridge.HP28674: There is only one 'real'
instance of this object on port 2.roobsolete INTEGER .1.3.6.1.4.1.11.2.14.3.10.1 |
x25T1TimerPeriod of time used to timeout retransmits for
X25.rwobsolete TimeTicks -- .1.3.6.1.4.1.11.2.14.3.10.2 |
x25N2CountNumber of retries to be performed during X.25
communication.rwobsolete INTEGER .1.3.6.1.4.1.11.2.14.3.10.3 |
x25T3TimerPeriod of idle time before a disconnect is
executed for X25.rwobsolete TimeTicks -- .1.3.6.1.4.1.11.2.14.3.10.4 |
icfSecurity OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.4 |
icfSecurPasswordThis variable contains a string which is used
both as the community name for the password
community, and as the login password for the
console port. This community name is needed for
most SET operations. In addition, the variables
in the ICF security group are only visible within
the password community, and must use the value of
this variable as the community name for GET
operations. If the value of this variable is
equal to the null string, the community name
'public' or the null string will be treated the
same as the password community.rw DisplayString .1.3.6.1.4.1.11.2.14.4.1 |
icfSecurAuthAnyMgrWhen this variable is set to enabled, any manager
with a valid community name may perform SET
operations on this device. In this configuration,
entries in the icfSecurAuthMgrTable are used only
for trap destinations. If this variable is set to
disabled, a manager must be in the
icfSecurAuthMgrTable and have a valid community
name in order to perform SET operations.rw Enumeration .1.3.6.1.4.1.11.2.14.4.2 |
icfSecurAuthMgrTableThis table contains a list of addresses of
managers that are allowed to perform SET
operations on this device, and controls the
destination addresses for traps. If
icfSecurAuthAnyMgr is set to disabled, a manager
must be in this table and use the correct
community name for the password community in order
to perform a GET operation on this table. SEQUENCE OF IcfSecurAuthMgrEntry .1.3.6.1.4.1.11.2.14.4.3 |
icfSecurAuthMgrEntryAn entry in the icfSecurAuthMgrTable containing
information about a single manager. IcfSecurAuthMgrEntry .1.3.6.1.4.1.11.2.14.4.3.1 |
icfAuthMgrIndexThis object contains the index which uniquely
identifies this entry in the
icfSecurAuthMgrTable.ro INTEGER .1.3.6.1.4.1.11.2.14.4.3.1.1 |
icfAuthMgrIpAddressThe IP address of a manager that is allowed to
manage this device. Setting this variable to a
nonzero value will clear the corresponding
instance of the icfAuthMgrIpxAddress variable.rw IpAddress .1.3.6.1.4.1.11.2.14.4.3.1.2 |
icfAuthMgrIpxAddressThe IPX address of a manager that is allowed to
manage this device. Setting this variable to a
valid IPX address will clear the corresponding
instance of the icfAuthMgrIpAddress variable.rw OCTET STRING .1.3.6.1.4.1.11.2.14.4.3.1.3 |
icfAuthMgrRcvTrapsIf this variable is set to enabled, any traps
generated by this device will be sent to the
manager indicated by the corresponding instance of
either icfAuthMgrIpAddress or
icfAuthMgrIpxAddress, whichever is valid.rw Enumeration .1.3.6.1.4.1.11.2.14.4.3.1.4 |
icfSecurIntruder OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.4.4 |
icfSecurIntruderFlagIf this object is set to 'valid', the remainder
of the intruder objects contain information about
an authentication failure. The Security LED on
the device will blink if this flag is set to
'valid'. The intruder objects will not be
overwritten as long as this flag is set to
'valid'. Setting this flag to 'invalid' will turn
off the Security LED if there are no other
current violations, and will allow the intruder
objects to be overwritten by subsequent
authentication failures.rw Enumeration .1.3.6.1.4.1.11.2.14.4.4.1 |
icfSecurIntruderIpAddressThe IP address of the manager that caused the
authentication failure. Only one of
icfSecurIntruderIpAddress and
icfSecurIntruderIPXAddress will be valid.ro IpAddress .1.3.6.1.4.1.11.2.14.4.4.2 |
icfSecurIntruderIpxAddressThe IPX address of the manager that caused the
authentication failure. Only one of
icfSecurIntruderIpAddress and
icfSecurIntruderIPXAddress will be valid.ro OCTET STRING .1.3.6.1.4.1.11.2.14.4.4.3 |
icfSecurIntruderTimeThe value of sysUpTime when the authentication
failure occurred. A value of 0 indicates that the
agent has been reset since this authentication
failure occurred.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.11.2.14.4.4.4 |
icfConfig OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.5 |
icfConfigIfTableThis table contains per-interface configuration
information that will take effect after the next
reset of the device. SEQUENCE OF IcfConfigIfEntry .1.3.6.1.4.1.11.2.14.5.1 |
icfConfigIfEntryAn entry in the icfConfigIfTable containing
information about a single interface. IcfConfigIfEntry .1.3.6.1.4.1.11.2.14.5.1.1 |
icfConfigIfIndexThe index of the interface which this information
contains configuration information for. The
interface identified by a particular value of this
index is the same interface identified by the same
value of ifIndex.ro INTEGER .1.3.6.1.4.1.11.2.14.5.1.1.1 |
icfConfigIfIpAddressThis variable contains the IP address for this
interface which will be used after the next reset
of the device.rw IpAddress .1.3.6.1.4.1.11.2.14.5.1.1.2 |
icfConfigIfNetMaskThis variable contains the IP subnet mask for
this interface which will be used after the next
reset of the device.rw IpAddress .1.3.6.1.4.1.11.2.14.5.1.1.3 |
icfConfigIfDefaultGateThis variable contains the IP address of the
default router for this interface which will be
used after the next reset of the device.rw IpAddress .1.3.6.1.4.1.11.2.14.5.1.1.4 |
icfConfigIpTTLThis variable contains the default IP time to
live which will be used after the next reset of
the device.rw INTEGER .1.3.6.1.4.1.11.2.14.5.2 |
icfConfigBootpEnableSetting this flag to 'enabled' (the default) will
clear any existing IP address configuration for
this device, and will cause the device to use the
Bootp protocol to obtain its IP configuration
after the next reset. This flag must be set to
'disabled' in order to configure an IP address for
the device. Setting this flag to 'disabled' will
prevent the Bootp protocol from running. Setting
this flag to 'disabled' when there is no IP
address configured will disable the IP protocol
stack on this device.rw Enumeration .1.3.6.1.4.1.11.2.14.5.3 |
icfDot12Draft OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.8 |
icfVgRepeater OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.8.1 |
icfVgBasic OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.8.1.1 |
icfVgBasicRptr OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.8.1.1.1 |
icfVgMACAddressThe MAC address used by the repeater when it
initiates training on the uplink port. Repeaters
are allowed to train with an assigned MAC address or
a null (all zeroes) MAC address.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.8.1.1.1.1 |
icfVgCurrentFramingTypeThe type of framing (802.3 or 802.5) currently in
use by the repeater.ro Enumeration .1.3.6.1.4.1.11.2.14.8.1.1.1.2 |
icfVgDesiredFramingTypeThe type of framing which will be used by the
repeater after the next time it is reset. The value
of this object should be preserved across repeater
resets and power failuresrw Enumeration .1.3.6.1.4.1.11.2.14.8.1.1.1.3 |
icfVgFramingCapabilityThe type of framing this repeater is capable of
supporting.ro Enumeration .1.3.6.1.4.1.11.2.14.8.1.1.1.4 |
icfVgTrainingVersionThe highest version bits (vvv bits) supported by the
repeater during training.ro INTEGER .1.3.6.1.4.1.11.2.14.8.1.1.1.5 |
icfVgRepeaterGroupCapacityThe icfVgGroupCapacity is the number of groups that
can be contained within the repeater. Within each
managed repeater, the groups are uniquely numbered in
the range from 1 to icfVgRepeaterGroupCapacity.
Some groups may not be present in the repeater, in
which case the actual number of groups present will
be less than icfVgRepeaterGroupCapacity. The number
of groups present is never greater than
icfVgRepeaterGroupCapacity.ro INTEGER .1.3.6.1.4.1.11.2.14.8.1.1.1.6 |
icfVgRepeaterHealthStateThe icfVgRepeaterHealthState object indicates the
operational state of the repeater. The
icfVgRepeaterHealthText may be consulted for more
specific information about the state of the
repeater's health.
In the case of multiple kinds of failures (e.g.,
repeater failure and port failure), the value of this
attribute shall reflect the highest priority failure
in the following order, listed highest priority
first:
rptrFailure(3)
groupFailure(4)
portFailure(5)
generalFailure(6).ro Enumeration .1.3.6.1.4.1.11.2.14.8.1.1.1.7 |
icfVgRepeaterHealthTextThe health text object is a text string that
provides information relevant to the operational
state of the repeater. Agents may use this string to
provide detailed information on current failures,
including how they were detected, and/or instructions
for problem resolution. The contents are agent
specific.ro DisplayString .1.3.6.1.4.1.11.2.14.8.1.1.1.8 |
icfVgRepeaterResetSetting this object to reset(2) causes the repeater
to transition to its initial state as specified in
clause 12 [IEEE Draft Std 802.12].
Setting this object to noReset(1) has no effect. The
agent will always return the value noReset(1) when
this object is read.
After receiving a request to set this variable to
reset(2), the agent is allowed to delay the reset for
a short period. For example, the implementor may
choose to delay the reset long enough to allow the
SNMP response to be transmitted. In any event, the
SNMP response must be transmitted.
This action does not reset the management counters
defined in this document nor does it affect the
icfVgPortAdminStatus parameters. Included in this
action is the execution of a disruptive Self-Test
with the following characteristics: a) The nature
of the tests is not specified. b) The test resets
the repeater but without affecting management
information about the repeater. c) The test does not
inject packets onto any segment. d) Packets received
during the test may or may not be transferred.
e) The test does not interfere with management
functions.
After performing this self-test, the agent will
update the repeater health information (including
icfVgRepeaterHealthState and
icfVgRepeaterHealthText).rw Enumeration .1.3.6.1.4.1.11.2.14.8.1.1.1.9 |
icfVgRepeaterNonDisruptTestSetting this object to selfTest(2) causes the
repeater to perform an agent-specific, non-disruptive
self-test that has the following characteristics:
a) The nature of the tests is not specified. b) The
test does not change the state of the repeater or
management information about the repeater. c) The
test does not inject packets onto any segment.
d) The test does not prevent the relay of any
packets. e) The test does not interfere with
management functions.
After performing this test, the agent will update the
repeater health information (including
icfVgRepeaterHealthState and
icfVgRepeaterHealthText).
Note that this definition allows returning an 'okay'
result after doing a trivial test.
Setting this object to noSelfTest(1) has no effect.
The agent will always return the value noSelfTest(1)
when this object is read.rw Enumeration .1.3.6.1.4.1.11.2.14.8.1.1.1.10 |
icfVgBasicGroup OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.8.1.1.2 |
icfVgBasicGroupTableA table containing information about groups of
ports. SEQUENCE OF IcfVgBasicGroupEntry .1.3.6.1.4.1.11.2.14.8.1.1.2.1 |
icfVgBasicGroupEntryAn entry in the icfVgBasicGroupTable, containing
information about a single group of ports. IcfVgBasicGroupEntry .1.3.6.1.4.1.11.2.14.8.1.1.2.1.1 |
icfVgGroupIndexThis object identifies the group within the repeater
for which this entry contains information. This
value is never greater than
icfVgRepeaterGroupCapacity. INTEGER .1.3.6.1.4.1.11.2.14.8.1.1.2.1.1.1 |
icfVgGroupDescrA textual description of the group. This value
should include the full name and version
identification of the group's hardware type and
indicate how the group is differentiated from other
types of groups in the repeater. 'Plug-in Module,
Rev A' or 'Barney Rubble 100BaseVG 4-port socket
Version 2.1' are examples of valid group
descriptions.
It is mandatory that this only contain printable
ASCII characters.ro DisplayString .1.3.6.1.4.1.11.2.14.8.1.1.2.1.1.2 |
icfVgGroupObjectIDThe vendor's authoritative identification of the
group. This value may be allocated within the SMI
enterprises subtree (1.3.6.1.4.1) and provides a
straight-forward and unambiguous means for
determining what kind of group is being managed.
For example, this object could take the value
1.3.6.1.4.1.4242.1.2.14 if vendor 'Flintstones, Inc.'
was assigned the subtree 1.3.6.1.4.1.4242, and had
assigned the identifier 1.3.6.1.4.1.4242.1.2.14 to
its 'Wilma Flintstone 6-Port Plug-in Module.'ro OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.8.1.1.2.1.1.3 |
icfVgGroupOperStatusAn object that indicates the operational status of
the group.
A status of notPresent(4) indicates that the group is
temporarily or permanently physically and/or
logically not a part of the repeater. It is an
implementation-specific matter as to whether the
agent effectively removes notPresent entries from the
table.
A status of operational(2) indicates that the group
is functioning, and a status of malfunctioning(3)
indicates that the group is malfunctioning in some
way.ro Enumeration .1.3.6.1.4.1.11.2.14.8.1.1.2.1.1.4 |
icfVgGroupLastOperStatusChangeAn object that contains the value of sysUpTime at
the time that the value of the icfVgGroupOperStatus
object for this group last changed.
A value of zero indicates that the group's
operational status has not changed since the agent
last restarted.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.8.1.1.2.1.1.5 |
icfVgGroupPortCapacityThe icfVgGroupPortCapacity is the number of ports
that can be contained within the group. Valid range
is 1-1024. Within each group, the ports are uniquely
numbered in the range from 1 to
icfVgGroupPortCapacity. Some ports may not be
present in a given group instance, in which case the
actual number of ports present is less than
icfVgGroupPortCapacity. The number of ports present
is never greater than icfVgGroupPortCapacity.ro INTEGER .1.3.6.1.4.1.11.2.14.8.1.1.2.1.1.6 |
icfVgGroupCablesBundledThis configuration flag is used to select either
bundled or unbundled cabling. When this flag is
'someCablesBundled(1)' and the port is not
promiscuous or cascaded, frames received from ports
on this group and destined to go out multiple ports
on this group will be buffered completely before
being repeated out ports on this group. When this
flag is 'noCablesBundled(2)' or the port is
promiscuous or cascaded, these frames will be
repeated out ports on this group as the frame is
being received.
Note that the value 'someCablesBundled(1)' will work
in the vast majority of installations, regardless of
whether or not any cables are physically in a bundle,
since promiscuous and cascaded ports automatically
avoid the store and forward. The main situation in
which 'noCablesBundled(2)' is beneficial is when
there is a large amount of multicast traffic and the
cables are not in a bundle. The value of this
object should be preserved across repeater resets
and power failures.rw Enumeration .1.3.6.1.4.1.11.2.14.8.1.1.2.1.1.7 |
icfVgBasicPort OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.8.1.1.3 |
icfVgBasicPortTableA table containing information about ports. SEQUENCE OF IcfVgBasicPortEntry .1.3.6.1.4.1.11.2.14.8.1.1.3.1 |
icfVgBasicPortEntryAn entry in the icfVgBasicPortTable, containing
information about a single port. IcfVgBasicPortEntry .1.3.6.1.4.1.11.2.14.8.1.1.3.1.1 |
icfVgPortGroupIndexThis object identifies the group containing the port
for which this entry contains information. INTEGER .1.3.6.1.4.1.11.2.14.8.1.1.3.1.1.1 |
icfVgPortIndexThis object identifies the port within the group for
which this entry contains information. This value
can never be greater than icfVgGroupPortCapacity for
the associated group. INTEGER .1.3.6.1.4.1.11.2.14.8.1.1.3.1.1.2 |
icfVgPortTypeDescribes the type of port. One of the following:
cascadeExternal - Port is an uplink with physical
connections which are
externally visible
cascadeInternal - Port is an uplink with physical
connections which are not
externally visible, such as a
connection to an internal
backplane in a chassis
localExternal - Port is a downlink or local
port with externally visible
connections
localInternal - Port is a downlink or local
port with connections which are
not externally visible, such as
a connection to an internal
agent
'internal' is used to identify ports which place
traffic into the repeater, but do not have any
external connections. Note that both DTE and
cascaded repeater downlinks are considered 'local'
ports.ro Enumeration .1.3.6.1.4.1.11.2.14.8.1.1.3.1.1.3 |
icfVgPortAdminStatusPort enable/disable function. Enabling a disabled
port will cause training to be initiated. Setting
this object to disabled(2) disables the port. A
disabled port neither transmits nor receives. Once
disabled, a port must be explicitly enabled to
restore operation. A port which is disabled when
power is lost or when a reset is exerted shall remain
disabled when normal operation resumes.rw Enumeration .1.3.6.1.4.1.11.2.14.8.1.1.3.1.1.4 |
icfVgPortStatusCurrent status for the port as specified by the
PORT_META_STATE in the port process module of clause
12 [IEEE Draft Std 802.12].
During initialization or any link warning conditions,
icfVgPortStatus will be 'inactive(2)'.
When Training_Up is received by the repeater on a
local port (or when Training_Down is received on
a cascade port), icfVgPortStatus will change to
'training(3)' and icfVgTrainingResult can be
monitored to see the detailed status regarding
training.
When 24 consecutive good FCS packets are received and
the configuration bits are OK, icfVgPortStatus will
change to 'active(1)'.
A disabled port shall have a port status of
'inactive(2)'.ro Enumeration .1.3.6.1.4.1.11.2.14.8.1.1.3.1.1.5 |
icfVgPortSupportedPromiscModeThis object describes whether the port hardware is
capable of supporting promiscuous mode, single
address mode (i.e., repeater filters unicasts not
addressed to the end station attached to this port),
or both. A port for which icfVgPortType is equal to
'cascadeInternal' or 'cascadeExternal' will always
have a value of 'promiscModeOnly' for this object.ro Enumeration .1.3.6.1.4.1.11.2.14.8.1.1.3.1.1.6 |
icfVgPortSupportedCascadeModeThis object describes whether the port hardware is
capable of supporting cascaded repeaters, end nodes,
or both. A port for which icfVgPortType is equal to
'cascadeInternal' or 'cascadeExternal' will always
have a value of 'cascadePort' for this object.ro Enumeration .1.3.6.1.4.1.11.2.14.8.1.1.3.1.1.7 |
icfVgPortAllowedTrainTypeThis security object is set by the network manager
to configure what type of device is permitted to
connect to the port. One of the following values:
allowEndNodesOnly - only non-promiscuous
end nodes permitted.
allowPromiscuousEndNodes - promiscuous or non-
promiscuous end nodes
permitted
allowEndNodesOrRepeaters - repeaters or non-
promiscuous end nodes
permitted
allowAnything - repeaters, promiscuous
or non-promiscuous end
nodes permitted
For a port for which icfVgPortType is equal to
'cascadeInternal' or 'cascadeExternal', the
corresponding instance of this object may not be set
to 'allowEndNodesOnly' or 'allowPromiscuousEndNodes'.
The agent must reject a SET of this object if the
value includes no capabilities that are supported by
this port's hardware, as defined by the values of the
corresponding instances of
icfVgPortSupportedPromiscMode and
icfVgPortSupportedCascadeMode.rw Enumeration .1.3.6.1.4.1.11.2.14.8.1.1.3.1.1.8 |
icfVgPortLastTrainConfigThis 16 bit field contains the most recent training
configuration in an error-free training frame
sent by the end node connected to the port. For
cascade ports, this is the responder's configuration
field from the most recent error-free training
response frame received in response to training
initiated by this repeater. This object is formatted
as follows:
First Octet: Second Octet:
7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
+-+-+-+-+-+-+-+-+ +-+-+-+-+-+-+-+-+
|v|v|v|0|0|0|0|0| |0|0|0|F|F|P|P|R|
+-+-+-+-+-+-+-+-+ +-+-+-+-+-+-+-+-+
vvv: The version of the 802.12 training protocol
with which the training initiator is
compliant
FF: 00 = frameType88023 is requested
01 = frameType88025 is requested
10 = reserved
11 = either frameType88023 or frameType88025
is acceptable
PP: 00 = request singleAddressMode
01 = request promiscuousMode
10 = reserved
11 = reserved
R: 0 = request is from an end node
1 = request is from a repeaterro OCTET STRING .1.3.6.1.4.1.11.2.14.8.1.1.3.1.1.9 |
icfVgPortTrainingResultThis 18 bit field is used to indicate the result of
training. It contains two bits which indicate if
error-free training frames have been received, and it
also contains the 16 bits of the most recent valid
training response frame on the port.
First Octet: Second Octet: Third Octet:
7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
+-+-+-+-+-+-+-+-+ +-+-+-+-+-+-+-+-+ +-+-+-+-+-+-+-+-+
|0|0|0|0|0|0|V|G| |v|v|v|D|C|N|0|0| |0|0|0|F|F|P|P|R|
+-+-+-+-+-+-+-+-+ +-+-+-+-+-+-+-+-+ +-+-+-+-+-+-+-+-+
V: Valid: set when at least one error-free
training frame has been received. Indicates
the 16 training configuration bits in
icfVgPortLastTrainConfig and
icfVgPortTrainingResult contain valid
information. This bit is cleared when
icfVgPortStatus transitions to the
'inactive' or 'training' state.
G: LinkGood: indicates the link hardware is OK.
Set if 24 consecutive error-free training
packets have been received. Cleared when a
training packet with errors is received, and
when icfVgPortStatus transitions to the
'inactive' or 'training' state.
vvv: The version of the 802.12 training protocol
with which the training responder is
compliant
D: 0 = no duplicate address has been detected
1 = duplicate address has been detected
C: 0 = the requested configuration is
compatible with the port
1 = the requested configuration is not
compatible with the port. The FF, PP
and R bits indicate the configuration
which would be allowed (providing
N = 0).
N: 0 = access will be allowed, providing the
configuration is compatible (C = 0).
1 = access not allowed because of security
restrictions
FF: 00 = frameType88023 will be used
01 = frameType88025 will be used
10 = reserved
11 = reserved
PP: 00 = singleAddressMode will be used
01 = promiscuousMode will be used
10 = reserved
11 = reserved
R: 0 = requested access as an end node is
allowed
1 = requested access as a repeater is
allowed
If the port is in training, a management station can
examine this object to see if any training packets
have been passed successfully. If there have been
any good training packets, the Valid bit will be set
and the management station can examine the 16
training response bits to see if there is a duplicate
address, configuration, or security problem.
Note that on a repeater local port, this repeater
generates the training response bits, while on the
cascade port, the higher level repeater originated
the training response bits.ro OCTET STRING .1.3.6.1.4.1.11.2.14.8.1.1.3.1.1.10 |
icfVgPortPriorityEnableA configuration flag used to determine whether the
repeater will service high priority requests received
on the port as high priority or normal priority.
When 'false', high priority requests on this port
will be serviced as normal priority. The value of
this object should be preserved across repeater
resets and power failures. The setting of this
object has no effect on a cascade port.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.8.1.1.3.1.1.11 |
icfVgPortMediaTypeThe type of physical media in use. One of the
following values:
other undefined
unknown true state not known
pmdMissing PMD device not attached
utp4 4-pair unshielded twisted pair
stp2 2-pair shielded twisted pair
fibre 802.12 fibre optic cabling
This object may be 'unknown' if the implementation is
not capable of identifying the PMD media type, or
whether or not the PMD is even present.ro Enumeration .1.3.6.1.4.1.11.2.14.8.1.1.3.1.1.12 |
icfVgMonitor OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.8.1.2 |
icfVgMonRptr OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.8.1.2.1 |
icfVgMonGroup OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.8.1.2.2 |
icfVgMonPort OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.8.1.2.3 |
icfVgMonPortTableA table of performance and error statistics for the
ports. SEQUENCE OF IcfVgMonPortEntry .1.3.6.1.4.1.11.2.14.8.1.2.3.1 |
icfVgMonPortEntryAn entry in the icfVgMonPortTable, containing
performance and error statistics for a single port. IcfVgMonPortEntry .1.3.6.1.4.1.11.2.14.8.1.2.3.1.1 |
icfVgPortReadableFramesThis object is the number of good frames of valid
frame length that have been received on this port.
This counter is incremented by one for each frame
received on the port which is not counted by
icfVgPortIPMFrames or icfVgPortDataErrorFrames.ro Counter .1.3.6.1.4.1.11.2.14.8.1.2.3.1.1.1 |
icfVgPortReadableOctetsThis object is a count of the number of octets
contained in good frames that have been received on
this port. This counter is incremented by OctetCount
for each frame received on this port which has been
determined to be a readable frame (i.e. each frame
counted by icfVgPortReadableFrames).
Note that this counter may roll over very quickly.ro Counter .1.3.6.1.4.1.11.2.14.8.1.2.3.1.1.2 |
icfVgPortUnreadableOctetsThis object is a count of the number of octets
contained in invalid frames that have been received
on this port. This counter is incremented by
OctetCount for each frame received on this port which
is counted by icfVgPortIPMFrames or
icfVgPortDataErrorFrames. This counter can be
combined with icfVgPortReadableOctets to calculate
network utilization.
Note that this counter may roll over very quickly.ro Counter .1.3.6.1.4.1.11.2.14.8.1.2.3.1.1.3 |
icfVgPortHighPriorityFramesThis object is a count of high priority frames
that have been received on this port. This counter
is incremented by one for each high priority frame
received on this port, including readable, invalid,
and training frames. This counter does not include
normal priority frames which were priority promoted.ro Counter .1.3.6.1.4.1.11.2.14.8.1.2.3.1.1.4 |
icfVgPortHighPriorityOctetsThis object is a count of the number of octets
contained in high priority frames that have been
received on this port. This counter is incremented
by OctetCount for each frame received on this port
which is counted by icfVgPortHighPriorityFrames.
Note that this counter may roll over very quickly.ro Counter .1.3.6.1.4.1.11.2.14.8.1.2.3.1.1.5 |
icfVgPortBroadcastFramesThis object is a count of broadcast packets that
have been received on this port. This counter is
incremented by one for each readable frame received
on this port whose destination MAC address is the
broadcast address. Frames counted by this counter
are also counted by icfVgPortReadableFrames.ro Counter .1.3.6.1.4.1.11.2.14.8.1.2.3.1.1.6 |
icfVgPortMulticastFramesThis object is a count of multicast packets that
have been received on this port. This counter is
incremented by one for each readable frame received
on this port whose destination MAC address has the
group address bit set, but is not the broadcast
address. Frames counted by this counter are also
counted by icfVgPortReadableFrames, but not by
icfVgPortBroadcastFramesro Counter .1.3.6.1.4.1.11.2.14.8.1.2.3.1.1.7 |
icfVgPortIPMFramesThis object is a count of the number of frames that
have been received on this port with an invalid
packet marker and no PMI errors. A repeater will
write an invalid packet marker to the end of a frame
containing errors as it is forwarded through the
repeater to the other ports. This counter is
incremented by one for each frame received on this
port which has had an invalid packet marker added to
the end of the frame. This counter indicates
problems with remote cable segments, as opposed to
problems with cables directly attached to this
repeater.ro Counter .1.3.6.1.4.1.11.2.14.8.1.2.3.1.1.8 |
icfVgPortDataErrorFramesThis object is a count of errored frames received on
this port. This counter is incremented by one for
each frame received on this port with any of the
following errors: FCS (with no IPM), PMI erorrs
(excluding frames with an IPM error as the only PMI
error), oversize (with no IPM), or undersize (with no
IPM). Does not include packets counted by
icfVgPortIPMFrames. This counter indicates problems
with the cable directly attached to this repeater,
while icfVgPorrtIPMFrames indicates problems with
remote cables attached to other repeaters.ro Counter .1.3.6.1.4.1.11.2.14.8.1.2.3.1.1.9 |
icfVgPortPriorityPromotionsThis counter is incremented by one each time the
priority promotion timer has expired on this port and
a normal priority frame was priority promoted.ro Counter .1.3.6.1.4.1.11.2.14.8.1.2.3.1.1.10 |
icfVgAddrTrack OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.8.1.3 |
icfVgAddrTrackRptr OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.8.1.3.1 |
icfVgAddrTrackGroup OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.8.1.3.2 |
icfVgAddrTrackPort OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.8.1.3.3 |
icfVgAddrTrackTableTable of address mapping information about the
ports. SEQUENCE OF IcfVgAddrTrackEntry .1.3.6.1.4.1.11.2.14.8.1.3.3.1 |
icfVgAddrTrackEntryAn entry in the table, containing address mapping
information about a single port. IcfVgAddrTrackEntry .1.3.6.1.4.1.11.2.14.8.1.3.3.1.1 |
icfVgAddrLastTrainedAddressThis object is the MAC address of the last station
which succeeded in training on this port. A
cascaded repeater may train using the null address.
If no stations have succeeded in training on this
port since the agent began monitoring the port
activity, the agent shall return a string of length
zero.ro OCTET STRING .1.3.6.1.4.1.11.2.14.8.1.3.3.1.1.1 |
icfVgAddrTrainedAddrChangesThis counter is incremented by one for each time
that the icfVgAddrLastTrainedAddress object for this
port has changed.ro Counter .1.3.6.1.4.1.11.2.14.8.1.3.3.1.1.2 |
hpicfAdmin OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.10 |
hpicfDomains OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.10.1 |
hpicfLLCDomain OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.10.1.1 |
hpicfObjects OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11 |
hpicfCommon OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.1 |
hpicfChain OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.1.1 |
hpicfChainMaxMembersThe maximum number of devices that can be
supported on the Distributed Management Chain from
this agent.ro INTEGER .1.3.6.1.4.1.11.2.14.11.1.1.1 |
hpicfChainCurMembersThe number of devices currently on the
Distributed Management Chain connected to this
agent.ro INTEGER .1.3.6.1.4.1.11.2.14.11.1.1.2 |
hpicfChainLastChangeThe value of sysUpTime on this agent the last
time a device was added to or removed from the
Distributed Management Chain connected to this
agent.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.1.1.3 |
hpicfChainChangesA count of the number of times devices have been
added to or removed from the Distributed
Management Chain connected to this agent.ro Counter .1.3.6.1.4.1.11.2.14.11.1.1.4 |
hpicfChainTableA table of boxes currently connected to the same
Distributed Management Chain as this agent. SEQUENCE OF HpicfChainEntry .1.3.6.1.4.1.11.2.14.11.1.1.5 |
hpicfChainEntryAn entry in the table describing a single box on
the Distributed Management Chain connected to this
device. HpicfChainEntry .1.3.6.1.4.1.11.2.14.11.1.1.5.1 |
hpicfChainIdAn identifier which uniquely identifies this
particular box. In practice, this will be a box
serial number or MAC address.ro OCTET STRING .1.3.6.1.4.1.11.2.14.11.1.1.5.1.1 |
hpicfChainObjectIdThe authoritative identification of the box which
provides an easy and unambiguous means for
determining the type of box.ro OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.1.1.5.1.2 |
hpicfChainTimestampThe value of the agent's sysUpTime at which this
box was last initialized. If the box has not been
initialized since the last reinitialization of the
agent, then this object has a zero value.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.1.1.5.1.3 |
hpicfChainHasAgentThis object will contain the value 'true' if this
box contains at least one network management agent
capable of responding to SNMP requests, and will
contain the value 'false' otherwise.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.1.1.5.1.4 |
hpicfChainThisBoxThis object will contain the value 'true' if this
entry in the chain table corresponds to the box
which contains the agent which is responding to
this SNMP request, and will contain the value
'false' otherwise.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.1.1.5.1.5 |
hpicfChainLocationThis byte is settable by a management station and
is not interpreted by the agent. The intent is
that a management station can use it to assign an
ordering to boxes on the chain that can later be
used when displaying the chain.rw INTEGER .1.3.6.1.4.1.11.2.14.11.1.1.5.1.6 |
hpicfChainViewTableThis table contains one entry for each box on the
Distributed Management Chain for which this agent
is able to act as a proxy. SEQUENCE OF HpicfChainViewEntry .1.3.6.1.4.1.11.2.14.11.1.1.6 |
hpicfChainViewEntryAn entry in the hpicfChainViewTable containing
information about how to proxy to a single box. HpicfChainViewEntry .1.3.6.1.4.1.11.2.14.11.1.1.6.1 |
hpicfChainViewIdAn identifier which uniquely identifies this
particular box. In practice, this will be a box
serial number or MAC address.ro OCTET STRING .1.3.6.1.4.1.11.2.14.11.1.1.6.1.1 |
hpicfChainViewNameThe local name of this box. This is used by the
proxy agent for the box to determine which box on
the Distributed Management Chain is being
addressed. If an agent does not use this method
to distinguish proxy destinations, it should
return a zero length octet string for this object.
For SNMPv1, the destination box is specified by
appending this name to the proxy agent's community
name. For example, if this agent has a community
with a community name of 'public', and the value
of this object is 'repeater1', the community
'public/repeater1' will specify that the agent
should proxy to the public community of the
'repeater1' box.
The default value for this object for box-level
repeaters is an ASCII hex representation of the
low-order three bytes of the device MAC address.ro DisplayString .1.3.6.1.4.1.11.2.14.11.1.1.6.1.2 |
hpicfChassis OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.1.2 |
hpicfChassisIdAn identifier that uniquely identifies this
particular chassis. This will be the same value
as the instance of hpicfChainId for this chassis.ro OCTET STRING .1.3.6.1.4.1.11.2.14.11.1.2.1 |
hpicfChassisNumSlotsThe number of slots in this chassis.ro INTEGER .1.3.6.1.4.1.11.2.14.11.1.2.2 |
hpicfSlotTableA table that contains information on all the
slots in this chassis. SEQUENCE OF HpicfSlotEntry .1.3.6.1.4.1.11.2.14.11.1.2.3 |
hpicfSlotEntryInformation about a slot in a chassis HpicfSlotEntry .1.3.6.1.4.1.11.2.14.11.1.2.3.1 |
hpicfSlotIndexThe slot number within the box for which this
entry contains information.ro INTEGER .1.3.6.1.4.1.11.2.14.11.1.2.3.1.1 |
hpicfSlotObjectIdThe authoritative identification of the card
plugged into this slot in this chassis. A value
of { 0 0 } indicates an empty slot.ro OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.1.2.3.1.2 |
hpicfSlotLastChangeThe value of the agent's sysUpTime at which a
card in this slot was last inserted or removed.
If no module has been inserted or removed since
the last reinitialization of the agent, this
object has a zero value.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.1.2.3.1.3 |
hpicfSlotDescrA textual description of the card plugged into
this slot in this chassis, including the product
number and version information.ro DisplayString .1.3.6.1.4.1.11.2.14.11.1.2.3.1.4 |
hpicfEntityTableA table that contains information about the
(logical) networking devices contained in this
chassis. SEQUENCE OF HpicfEntityEntry .1.3.6.1.4.1.11.2.14.11.1.2.4 |
hpicfEntityEntryInformation about a single logical networking
device contained in this chassis. HpicfEntityEntry .1.3.6.1.4.1.11.2.14.11.1.2.4.1 |
hpicfEntityIndexAn index that uniquely identifies the logical
network device for which this entry contains
information.ro INTEGER .1.3.6.1.4.1.11.2.14.11.1.2.4.1.1 |
hpicfEntityFunctionThe generic function provided by the logical
network device. The value is a sum. Starting
from zero, for each type of generic function that
the entity performs, 2 raised to a power is added
to the sum. The powers are according to the
following table:
Function Power
other 0
repeater 1
bridge 2
router 3
agent 5
For example, an entity performing both bridging
and routing functions would have a value of 12
(2^2 + 2^3).ro INTEGER .1.3.6.1.4.1.11.2.14.11.1.2.4.1.2 |
hpicfEntityObjectIdThe authoritative identification of the logical
network device which provides an unambiguous means
of determining the type of device. The value of
this object is analagous to MIB-II's sysObjectId.ro OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.1.2.4.1.3 |
hpicfEntityDescrA textual description of this device, including
the product number and version information. The
value of this object is analogous to MIB-II's
sysDescr.ro DisplayString .1.3.6.1.4.1.11.2.14.11.1.2.4.1.4 |
hpicfEntityTimestampThe value of the agent's sysUpTime at which this
logical network device was last reinitialized. If
the entity has not been reinitialized since the
last reinitialization of the agent, then this
object has a zero value.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.1.2.4.1.5 |
hpicfSlotMapTableA table that contains information about which
entities are in which slots in this chassis. SEQUENCE OF HpicfSlotMapEntry .1.3.6.1.4.1.11.2.14.11.1.2.5 |
hpicfSlotMapEntryA relationship between a slot and an entity in
this chassis. Such a relationship exists if the
particular slot is occupied by a physical module
performing part of the function of the particular
entity. HpicfSlotMapEntry .1.3.6.1.4.1.11.2.14.11.1.2.5.1 |
hpicfSlotMapSlotA slot number within the chassis which contains
(part of) this entity.ro INTEGER .1.3.6.1.4.1.11.2.14.11.1.2.5.1.1 |
hpicfSlotMapEntityThe entity described in this mapping.ro INTEGER .1.3.6.1.4.1.11.2.14.11.1.2.5.1.2 |
hpicfSensorTableA table that contains information on all the
sensors in this chassis SEQUENCE OF HpicfSensorEntry .1.3.6.1.4.1.11.2.14.11.1.2.6 |
hpicfSensorEntryInformation about a sensor in a chassis HpicfSensorEntry .1.3.6.1.4.1.11.2.14.11.1.2.6.1 |
hpicfSensorIndexAn index that uniquely identifies the sensor for
which this entry contains information.ro INTEGER .1.3.6.1.4.1.11.2.14.11.1.2.6.1.1 |
hpicfSensorObjectIdThe authoritative identification of the kind of
sensor this is.ro OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.1.2.6.1.2 |
hpicfSensorNumberA number which identifies a particular sensor
from other sensors of the same kind. For
instance, if there are many temperature sensors in
this chassis, this number whould identify a
particular temperature sensor in this chassis.ro INTEGER .1.3.6.1.4.1.11.2.14.11.1.2.6.1.3 |
hpicfSensorStatusActual status indicated by the sensor.ro Enumeration .1.3.6.1.4.1.11.2.14.11.1.2.6.1.4 |
hpicfSensorWarningsThe number of times hpicfSensorStatus has entered
the 'warning'(3) state.ro Counter .1.3.6.1.4.1.11.2.14.11.1.2.6.1.5 |
hpicfSensorFailuresThe number of times hpicfSensorStatus has entered
the 'bad'(2) state.ro Counter .1.3.6.1.4.1.11.2.14.11.1.2.6.1.6 |
hpicfSensorDescrA textual description of the sensor.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.1.2.6.1.7 |
hpicfChassisAddrTableA table of network addresses for entities in this
chassis. The primary use of this table is to map
a specific entity address to a specific chassis.
Note that this table may not be a complete list of
network addresses for this entity. SEQUENCE OF HpicfChassisAddrEntry .1.3.6.1.4.1.11.2.14.11.1.2.7 |
hpicfChassisAddrEntryAn entry containing a single network address being
used by a logical network device in this chassis. HpicfChassisAddrEntry .1.3.6.1.4.1.11.2.14.11.1.2.7.1 |
hpicfChasAddrTypeThe kind of network address represented in this
entry. Enumeration .1.3.6.1.4.1.11.2.14.11.1.2.7.1.1 |
hpicfChasAddrAddressThe network address being used by the logical
network device associated with this entry, formatted
according to the value of the associated instance of
hpicfChasAddrType.
For hpicfChasAddrType of ipAddr, this value is four
octets long, with each octet representing one byte of
the IP address, in network byte order.
For hpicfChasAddrType of ipxAddr, this value is ten
octets long, with the first four octets representing
the IPX network number in network byte order,
followed by the six byte host number in network byte
order.
For hpicfChasAddrType of macAddr, this value is six
octets long, representing the MAC address in
canonical order. OCTET STRING .1.3.6.1.4.1.11.2.14.11.1.2.7.1.2 |
hpicfChasAddrEntityAn index that uniquely identifies the logical
network device in this chassis that is using this
network address..ro INTEGER .1.3.6.1.4.1.11.2.14.11.1.2.7.1.3 |
hpicfDownload OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.1.3 |
hpicfDownloadTableA table of firmware downloads to this device.
There will at any time be either 0 or 1 rows in
this table, and the only valid index for this
table is 1. It is only a table so that we may
take advantage of the RowStatus textual convention
for configuring the download parameters. SEQUENCE OF HpicfDownloadEntry .1.3.6.1.4.1.11.2.14.11.1.3.1 |
hpicfDownloadEntryThe row in the hpicfDownloadTable containing the
download parameters. HpicfDownloadEntry .1.3.6.1.4.1.11.2.14.11.1.3.1.1 |
hpicfDownloadIndexThe index which uniquely identifies this row.
The only legal value for this object is 1.ro Enumeration .1.3.6.1.4.1.11.2.14.11.1.3.1.1.1 |
hpicfDownloadOwnerAddressThe transport address of the management station
that initiated this download attempt, formatted
according to the value of the associated instance
of hpicfDownloadOwnerDomain.ro TAddress .1.3.6.1.4.1.11.2.14.11.1.3.1.1.2 |
hpicfDownloadOwnerDomainThe kind of transport service used by the
management station that initiated this download
attempt.ro OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.1.3.1.1.3 |
hpicfDownloadTAddressThe transport address of the node to download
firmware from, formatted according to the value of
the associated instance of hpicfDownloadTDomain.
An attempt to modify this value will fail if the
associated hpicfDownloadStatus object would be
equal to 'active' both before and after the
modification attempt.rw TAddress .1.3.6.1.4.1.11.2.14.11.1.3.1.1.4 |
hpicfDownloadTDomainThe kind of transport service to be used for the
download. Currently supports snmpUDPDomain and
snmpIPXDomain.
An attempt to modify this value will fail if the
associated hpicfDownloadStatus object would be
equal to 'active' both before and after the
modification attempt.rw OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.1.3.1.1.5 |
hpicfDownloadFilenameFilename and path of file to download (maximum
length of 63 characters + NULL).
An attempt to modify this value will fail if the
associated hpicfDownloadStatus object would be
equal to 'active' both before and after the
modification attempt.rw DisplayString .1.3.6.1.4.1.11.2.14.11.1.3.1.1.6 |
hpicfDownloadResetTypeThe type of reset to perform after completion of
the firmware download. Note that not all agents
will support all possible values, and there may
be other agent-specific values for this object.rw Enumeration .1.3.6.1.4.1.11.2.14.11.1.3.1.1.7 |
hpicfDownloadErrorStatusStatus of download. The first seven codes are
equal to the codes defined by the TFTP protocol.
'notDefined' is the same as TFTP protocol error 0.
The following are the other possible values for this
object:
corruptFile - the agent detected a problem
with the download file format.
noServer - the TFTP server at
hpicfDownloadTAddress did not
respond to the TFTP request.
tftpTimeout - the download was aborted due
to excessive timeouts.
hardwareError - there was a hardware problem
on the agent that forced an
abort of the download (see
hpicfDownloadErrorText for
more detailed information).
success - the download has completed
successfully.
aborted - the download was aborted by
setting the
hpicfDownloadStatus to
'notInService' or 'delete'.
inProgress - the TFTP transfer is currently
active.
idle - means that the download has
not yet started (i.e. the
value of hpicfDownloadStatus
has not yet been set to
'active').
erasingEeprom - the agent is currently erasing
the EEPROM device. Currently
only used on JetDirect agents.
incompleteFirmware - the agent is running an
incomplete version of firmware
and requires a download.
Currently only used on
JetDirect agents.
requirePowerCycle - the agent must be power cycled
to run the newly downloaded
firmware. Currently only used
on JetDirect agents.
cannotUpgrade - the agent's current firmware
revision cannot be upgraded to
the revision in the download
file.
cannotDowngrade - the agent's current firmware
revision cannot be downgraded
to the revision in the
download file.ro Enumeration .1.3.6.1.4.1.11.2.14.11.1.3.1.1.8 |
hpicfDownloadErrorTextA textual description of the current error status
of the firmware download.ro DisplayString .1.3.6.1.4.1.11.2.14.11.1.3.1.1.9 |
hpicfDownloadStatusThe status of this download entry. This object
may not be set to 'active' unless the following
columnar objects exist in this row:
hpicfDownloadTAddress, hpicfDownloadTDomain,
hpicfDownloadFilename, and
hpicfDownloadResetType.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.1.3.1.1.10 |
hpicfDownloadLogMaxSizeThe maximum number of the download log entries
supported by this agent. Note that 0 is a
legal value for this variable.ro INTEGER .1.3.6.1.4.1.11.2.14.11.1.3.2 |
hpicfDownloadLogSizeThe number of download log entries currently in
the hpicfDownloadLogTable.ro Gauge .1.3.6.1.4.1.11.2.14.11.1.3.3 |
hpicfDownloadLogTableA log of the hpicfDownloadSize most recent
download attempts to this device. The first entry
in the table is the oldest. SEQUENCE OF HpicfDownloadLogEntry .1.3.6.1.4.1.11.2.14.11.1.3.4 |
hpicfDownloadLogEntryAn entry in the hpicfDownloadLogTable containing
information about a single download attempt. HpicfDownloadLogEntry .1.3.6.1.4.1.11.2.14.11.1.3.4.1 |
hpicfDlLogIndexThe index of this entry in the download log
table. Index 1 will always contain the oldest
entry. If the table is full when a download
attempt is made, the new entry becomes the last
entry (hpicfDownloadLogMaxSize), and all earlier
entries are shifted down by one entry, removing
the old index 1.ro INTEGER .1.3.6.1.4.1.11.2.14.11.1.3.4.1.1 |
hpicfDlLogOwnerAddressThe transport address of the management station
that attempted to initiate a download of this
device, formatted according to the value of
hpicfDlLastOwnerDomain.ro TAddress .1.3.6.1.4.1.11.2.14.11.1.3.4.1.2 |
hpicfDlLogOwnerDomainThe kind of transport service used by the
management station that attempted to initiate a
download of this device.ro OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.1.3.4.1.3 |
hpicfDlLogTAddressThe transport address of the node from which this
device attempted to download firmware, formatted
according to the value of hpicfDlLastTDomain.ro TAddress .1.3.6.1.4.1.11.2.14.11.1.3.4.1.4 |
hpicfDlLogTDomainThe kind of transport service which was used for
the attempt to download firmware to this device.ro OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.1.3.4.1.5 |
hpicfDlLogFilenameThe filename from which this device attempted to
download firmware.ro DisplayString .1.3.6.1.4.1.11.2.14.11.1.3.4.1.6 |
hpicfDlLogResetTypeThe type of reset requested to be performed
after completion of the firmware download
attempt.ro Enumeration .1.3.6.1.4.1.11.2.14.11.1.3.4.1.7 |
hpicfDlLogErrorStatusThe result of the attempt to download firmware to
this device. The values are the same as the
corresponding values of hpicfDownloadErrorStatus.ro Enumeration .1.3.6.1.4.1.11.2.14.11.1.3.4.1.8 |
hpicfDlLogErrorTextA textual description of the final error status
of the attempt to download firmware to this
device.ro DisplayString .1.3.6.1.4.1.11.2.14.11.1.3.4.1.9 |
hpicfBasic OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.1.4 |
hpicfResetWhen this object is set to to 'normalReset' it
results in a 'warm' reset, which does not clear
the parameters in NOVRAM to factory defaults. When
set to 'factoryReset', it results in NOVRAM being set
to factory defaults. When this object is set, the
agent replies, dallies a short time to allow the
reply to be emitted from the device, then performs
the reset. When read, this object always returns
'noReset'.rw Enumeration .1.3.6.1.4.1.11.2.14.11.1.4.1 |
hpicfSelfTestSelf test is invoked by setting this flag to
'stExecute'. When the object changes to 'stSuccess',
the test has completed successfully. Icf devices
will 'hard-fail' if the test does not succeed.rw Enumeration .1.3.6.1.4.1.11.2.14.11.1.4.2 |
hpicfRepeater OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.2 |
hpRptrBasic OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.2.1 |
hpRptrBasicGlobal OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.2.1.1 |
hpRptrEntityNameThe local name of this repeater. This is the
same value as hpicfEntityName in the case where
there is Distributed Management Protocol to access
this device.
For SNMPv1, this name is appended to the agent
community name to obtain a community name to use
to specify that the agent should proxy to this
repeater. For example, if this agent has a
community with a community name of 'public', and
the value of this object is 'repeater1', the
community 'public/repeater1' will specify that the
agent should proxy to the public community of the
repeater1 box to obtain management information
about this repeater.
If an agent receives a management request where
the localEntity is not specified, it will default
to the local repeater on which this agent is
executing.ro DisplayString .1.3.6.1.4.1.11.2.14.11.2.1.1.1 |
hpRptrThinlanFaultWhen set to 'true' this object causes the Fault
Led to blink if the ThinLan Port is segmented.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.2.1.1.2 |
hpRptrSqeEnabledWhen 'true', this flag indicates that SQE has
been detected for the last ten agent transmits and
there is a high probability that the SQE switch on
the transceiver attached to the AUI port is set to
Enabled, when it should be Disabled.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.2.1.1.3 |
hpRptrRobustHealingWhen this flag is set to 'true', it enables
robust port healing mode. The 802.3 specification
states that a segmented port is healed by
successfully transmitting or receiving a packet on
the port. This mode disables port healing on
successful packet reception and requires that a
packet be successfully transmitted on a port in
order for a segmented port to be healed.
Note that it is illegal to set this variable to
'true' on a repeater that does not have a local
network management agent.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.2.1.1.4 |
hpRptrBasicGroup OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.2.1.2 |
hpRptrBasicGroupTableHP specific extensions to the rptrGroupTable. SEQUENCE OF HpRptrBasicGroupEntry .1.3.6.1.4.1.11.2.14.11.2.1.2.1 |
hpRptrBasicGroupEntryAn entry in the table, containing HP extensions
for a specific group. HpRptrBasicGroupEntry .1.3.6.1.4.1.11.2.14.11.2.1.2.1.1 |
hpRptrGrpGroupIndexThe group within the repeater for which this
entry contains information. This object has the
same value as the corresponding instance of
rptrGroupIndex.ro INTEGER .1.3.6.1.4.1.11.2.14.11.2.1.2.1.1.1 |
hpRptrGrpPortsAdminStatusThe hpRptrGrpPortsAdminStatus is a bit map of the
state of the rptrPortAdminStatus object for all
of the ports in this group. The object has a one
bit for each port for which the value of
rptrPortAdminStatus is equal to 'enabled(1)' and
a zero bit for each port for which the value of
rptrPortAdminStatus is equal to 'disabled(2)'.
The bits are placed into the OCTET STRING in the
following order:
octet 0 octet 1 octet 2 ...
bits 7-0 bits 7-0 bits 7-0 ...
ports 1-8 ports 9-16 ports 17-24 ...
Values of unused bits in the last octet are
undefined.ro OCTET STRING .1.3.6.1.4.1.11.2.14.11.2.1.2.1.1.2 |
hpRptrGrpPortsSegStatusThe hpRptrGrpPortsSegStatus is a bit map of the
state of the rptrPortAutoPartitionState of all of
the ports in this group. The object has a one
bit for each port for which the value of
rptrPortAutoPartitionState is equal to
'notAutoPartitioned(1)' and a zero bit for each
port for which the value of
rptrPortAutoPartitionState is equal to
'autoPartitioned(2)'.
The bits are placed into the OCTET STRING in the
following order:
octet 0 octet 1 octet 2 ...
bits 7-0 bits 7-0 bits 7-0 ...
ports 1-8 ports 9-16 ports 17-24 ...
Values of unused bits in the last octet are
undefined.ro OCTET STRING .1.3.6.1.4.1.11.2.14.11.2.1.2.1.1.3 |
hpRptrGrpPortsMediaAvailableThe hpRptrGrpPortsMediaAvailable is a bit map of
the state of the rpMauMediaAvailable object for
all of the ports in this group. The object has a
one bit for each port for which the value of
rpMauMediaAvailable is equal to 'available(3)'
and a zero bit for each port for which the value
of rpMauMediaAvailable is not equal to
'available(3)'.
The bits are placed into the OCTET STRING in the
following order:
octet 0 octet 1 octet 2 ...
bits 7-0 bits 7-0 bits 7-0 ...
ports 1-8 ports 9-16 ports 17-24 ...
Values of unused bits in the last octet are
undefined.ro OCTET STRING .1.3.6.1.4.1.11.2.14.11.2.1.2.1.1.4 |
hpRptrGrpPortsLinkbeatEnabledThe hpRptrGrpPortsLinkbeatEnabled is a bit map of
the state of the hpRptrPtLinkbeatEnable object for
all of the ports in this group. The object has a
one bit for each port for which the value of
hpRptrPtLinkbeatEnable is equal to 'true(1)' and
a zero bit for each port for which the value of
hpRptrPtLinkbeatEnable is equal to 'false(2)'.
The bits are placed into the OCTET STRING in the
following order:
octet 0 octet 1 octet 2 ...
bits 7-0 bits 7-0 bits 7-0 ...
ports 1-8 ports 9-16 ports 17-24 ...
Values of unused bits in the last octet are
undefined.ro OCTET STRING .1.3.6.1.4.1.11.2.14.11.2.1.2.1.1.5 |
hpRptrGrpPortsOperStatusThe hpRptrGrpPortsOperStatus is a bit map of the
state of all hub ports in the group. The object
has a 1 bit for each port that is enabled, not
segmented, and the media is available. Ports on
which these conditions are not true have a 0 bit.
The bits are placed into the OCTET STRING in the
following order:
octet 0 octet 1 octet 2 ...
bits 7-0 bits 7-0 bits 7-0 ...
ports 1-8 ports 9-16 ports 17-24 ...
Values of unused bits in the last octet are
undefined.ro OCTET STRING .1.3.6.1.4.1.11.2.14.11.2.1.2.1.1.6 |
hpRptrBasicPort OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.2.1.3 |
hpRptrBasicPtTableHP specific extensions to the rptrPortTable. SEQUENCE OF HpRptrBasicPtEntry .1.3.6.1.4.1.11.2.14.11.2.1.3.1 |
hpRptrBasicPtEntryAn entry in the table, containing HP extensions
for a specific port. HpRptrBasicPtEntry .1.3.6.1.4.1.11.2.14.11.2.1.3.1.1 |
hpRptrPtGroupIndexThe group containing the port for which this
entry contains information. This object has the
same value as the corresponding instance of
rptrPortGroupIndex.ro INTEGER .1.3.6.1.4.1.11.2.14.11.2.1.3.1.1.1 |
hpRptrPtPortIndexThe port within the group for which this entry
contains information. This object has the same
value as the corresponding instance of
rptrPortIndex.ro INTEGER .1.3.6.1.4.1.11.2.14.11.2.1.3.1.1.2 |
hpRptrPtLinkbeatEnableWhen this flag is set to 'true' the port's link
beat is enabled and when set to 'false' it is
disabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.2.1.3.1.1.3 |
hpRptrPtPolarityReversedThis object is used to indicate that the hub port
was wired with the positive/negative polarity of
its transmit and receive pairs reversed. Note
that the port will continue to operate in this
state, with the hub inverting the polarity
internally.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.2.1.3.1.1.4 |
hpRptrMonitor OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.2.2 |
hpRptrMonitorGlobal OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.2.2.1 |
hpRptrMonCounters OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.2.2.1.1 |
hpRptrMonGlobalFramesThe total number of frames of valid frame length
that have been received on all ports in this
repeater. This counter is the summation of the
values of the rptrMonitorPortReadableFrames
counter for all of the ports in this repeater.
Equivalently, this counter is the summation of the
values of the rptrMonitorGroupTotalFrames counter
for all of the port groups in this repeater.ro Counter .1.3.6.1.4.1.11.2.14.11.2.2.1.1.1 |
hpRptrMonGlobalOctetsThe total number of octets contained in the valid
frames that have been received on the ports in
this repeater. This counter is the summation of
the values of the rptrMonitorPortReadableOctets
counter for all of the ports in this repeater.
Equivalently, this counter is the summation of the
values of the rptrMonitorGroupTotalOctets counter
for all of the port groups in this repeater.ro Counter .1.3.6.1.4.1.11.2.14.11.2.2.1.1.2 |
hpRptrMonGlobalFCSErrorsThis counter is incremented by one for each frame
received on any port with the FCSError signal
asserted and the FramingError and CollisionEvent
signals deasserted and whose OctetCount is greater
than or equal to minFrameSize and less than or
equal to maxFrameSize (Ref: 4.4.2.1, IEEE 802.3
Std). This counter is the summation of the values
of the rptrMonitorPortFCSErrors counter for all of
the ports in this repeater.ro Counter .1.3.6.1.4.1.11.2.14.11.2.2.1.1.3 |
hpRptrMonGlobalAlignmentErrorsThis counter is incremented by one for each frame
received on any port with the FCSError and
FramingError signals asserted and CollisonEvent
signal deasserted and whose OctetCount is greater
than or equal to minFrameSize and less than or
equal to maxFrameSize (Ref: 4.4.2.1, IEEE 802.3
Std). If hpRptrMonGlobalAlignmentErrors is
incremented, then the hpRptrMonGlobalFCSErorrs
counter shall not be incremented for the same
frame. This counter is the summation of the
values of the rptrMonitorPortAlignmentErrors
counter for all of the ports in this repeater.ro Counter .1.3.6.1.4.1.11.2.14.11.2.2.1.1.4 |
hpRptrMonGlobalFrameTooLongsThis counter is incremented by one for each frame
received on any port whose OctetCount is greater
than maxFrameSize (Ref: 4.4.2.1, IEEE 802.3 Std).
If hpRptrMonGlobalFrameTooLongs is incremented,
then neither the hpRptrMonGlobalAlignmentErorrs
nor the hpRptrMonGlobalFCSErrors counter shall be
incremented for the frame. This counter is the
summation of the values of the
rptrMonitorPortFrameTooLongs counter for all of
the ports in this repeater.ro Counter .1.3.6.1.4.1.11.2.14.11.2.2.1.1.5 |
hpRptrMonGlobalShortEventsThis counter is incremented by one for each
CarrierEvent on any port with ActivityDuration
less than ShortEventMaxTime. ShortEventMaxTime is
greater than 74 bit times and less than 82 bit
times. ShortEventMaxTime has tolerances included
to provide for circuit losses between a
conformance test point at the AUI and the
measurement point within the state machine. This
counter is the summation of the values of the
rptrMonitorPortShortEvents counter for all of the
ports in this repeater.ro Counter .1.3.6.1.4.1.11.2.14.11.2.2.1.1.6 |
hpRptrMonGlobalRuntsThis counter is incremented by one for each
CarrierEvent on any port that meets one of the
following two conditions. Only one test need be
made. a) The ActivityDuration is greater than
ShortEventMaxTime and less than ValidPacketMinTime
and the CollisionEvent signal is deasserted. b)
The OctetCount is less than 64, the
ActivityDuration is greater than ShortEventMaxTime
and the CollisionEvent signal is deasserted.
ValidPacketMinTime is greater than or equal to 552
bit times but less than 565 bit times.
An event whose length is greater than 74 bit times
but less than 82 bit times shall increment either
the hpRptrMonGlobalShortEvents counter or the
hpRptrMonGlobalRunts counter but not both. A
CarrierEvent greater than or equal to 552 bit
times but less than 565 bit times may or may not
increment the hpRptrMonGlobalRunts counter.
ValidPacketMinTime has tolerances included to
provide for circuit losses between a conformance
test point at the AUI and the measurement point
within the state machine.
Runts usually indicate collision fragments, a
normal network event. This counter is the
summation of the values of the
rptrMonitorPortRunts counter for all of the ports
in this repeater.ro Counter .1.3.6.1.4.1.11.2.14.11.2.2.1.1.7 |
hpRptrMonGlobalCollisionsThis counter is incremented by one for any
CarrierEvent signal on any port for which the
CollisionEvent signal on any port is asserted.
This counter differs from
rptrMonitorTransmitCollisions in that it counts
all collisions seen by this repeater, even those
involving only a single port on this repeater,
whereas rptrMonitorTransmitCollisions counts only
collisions involving multiple ports on this
repeater.ro Counter .1.3.6.1.4.1.11.2.14.11.2.2.1.1.8 |
hpRptrMonGlobalLateEventsThis counter is incremented by one for each
CarrierEvent on any port in which the CollIn(X)
variable transitions to the value SQE (Ref:
9.6.6.2, IEEE 802.3 Std) while the
ActivityDuration is greater than the
LateEventThreshold. Such a CarrierEvent is
counted twice, as both hpRptrMonGlobalCollisions
and hpRptrMonGlobalLateEvents. The
LateEventThreshold is greater than 480 bit times
and less than 565 bit times. LateEventThreshold
has tolerances included to permit an
implementation to build a single threshold to
serve as both the LateEventThreshold and
ValidPacketMinTime threshold. This counter is the
summation of the values of the
rptrMonitorPortLateEvents counter for all of the
ports in this repeater.ro Counter .1.3.6.1.4.1.11.2.14.11.2.2.1.1.9 |
hpRptrMonGlobalVeryLongEventsThis counter is incremented by one for each
CarrierEvent on any port whose ActivityDuration is
greater than the MAU Jabber Lockup Protection
timer TW3 (Ref: 9.6.1 & 9.6.5, IEEE 802.3 Std).
Other counters may be incremented as appropriate.
This counter is the summation of the values of the
rptrMonitorPortVeryLongEvents counter for all of
the ports in this repeater.ro Counter .1.3.6.1.4.1.11.2.14.11.2.2.1.1.10 |
hpRptrMonGlobalDataRateMismatchesThis counter is incremented by one for each frame
received on any port that meets all of the
following conditions: a) The CollisionEvent
signal is not asserted. b) The ActivityDuration
is greater than ValidPacketMinTime. c) The
frequency (data rate) is detectably mismatched
from the local transmit frequency. The exact
degree of mismatch is vendor specific and is to be
defined by the vendor for conformance testing.
When this event occurs, other counters whose
increment conditions were satisfied may or may not
also be incremented. This counter is the
summation of the values of the
rptrMonitorPortDatRateMismatches counter for all
of the ports in this repeater.ro Counter .1.3.6.1.4.1.11.2.14.11.2.2.1.1.11 |
hpRptrMonGlobalAutoPartitionsThis counter is incremented by one for each time
the repeater has automatically partitioned any
port. The conditions that cause port partitioning
are specified in the partition state machine in
Section 9 of the IEEE 802.3 Std. This counter is
the summation of the values of the
rptrMonitorPortAutoPartitions for all of the ports
in this repeater.ro Counter .1.3.6.1.4.1.11.2.14.11.2.2.1.1.12 |
hpRptrMonGlobalErrorsThe total number of errors which have occured
on any port in this repeater. This counter is
the summation of the values of other error
counters, namely:
hpRptrMonGlobalFCSErrors,
hpRptrMonGlobalAlignmentErrors,
hpRptrMonGlobalFrameTooLongs,
hpRptrMonGlobalShortEvents,
hpRptrMonGlobalLateEvents,
hpRptrMonGlobalVeryLongEvents, and
hpRptrMonGlobalDataRateMismatches.
Equivalently, this counter is the summation of
the values of the rptrMonitorPortTotalErrors
counter for all of the ports in this repeater, or
it is the summation of the values of
rptrMonitorGroupTotalErrors for all of the port
groups in this repeater.ro Counter .1.3.6.1.4.1.11.2.14.11.2.2.1.1.13 |
hpRptrMonGlobalUcastPacketsThis counter is incremented by one for each
unicast packet of valid frame length received on
any port. This counter is the summation of
hpRptrMonPortUcastPackets for all of the ports
in this repeater. This counter may not be
implemented for repeaters which do not have a
local network management agent.ro Counter .1.3.6.1.4.1.11.2.14.11.2.2.1.1.14 |
hpRptrMonGlobalBcastPacketsThis counter is incremented by one for each
broadcast packet of valid frame length received on
any port. This counter is the summation of
hpRptrMonPortBcastPackets for all of the ports
in this repeater. This counter may not be
implemented for repeaters which do not have a
local network management agent.ro Counter .1.3.6.1.4.1.11.2.14.11.2.2.1.1.15 |
hpRptrMonGlobalMcastPacketsThis counter is incremented by one for each
multicast packet of valid frame length received on
any port. This counter is the summation of
hpRptrMonPortMcastPackets for all of the ports in
this repeater. This counter may not be
implemented for repeaters which do not have a
local network management agent.ro Counter .1.3.6.1.4.1.11.2.14.11.2.2.1.1.16 |
hpRptrMonitorGroup OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.2.2.2 |
hpRptrMonitorPort OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.2.2.3 |
hpRptrMonPtTableTable of HP specific per port monitor objects. SEQUENCE OF HpRptrMonPtEntry .1.3.6.1.4.1.11.2.14.11.2.2.3.1 |
hpRptrMonPtEntryAn entry in the table, containing per port
objects for a single port. HpRptrMonPtEntry .1.3.6.1.4.1.11.2.14.11.2.2.3.1.1 |
hpRptrMonPtGroupIndexThe group containing the port for which this
entry contains information. This object has the
same value as the corresponding instance of
rptrMonitorPortGroupIndex.ro INTEGER .1.3.6.1.4.1.11.2.14.11.2.2.3.1.1.1 |
hpRptrMonPtPortIndexThe port within the group for which this entry
contains information. This object has the same
value as the corresponding instance of
rptrMonitorPortIndex.ro INTEGER .1.3.6.1.4.1.11.2.14.11.2.2.3.1.1.2 |
hpRptrMonPtUcastPacketsThis counter is incremented by one for each
unicast packet of valid frame length received on
this port. This object may not be implemented for
repeaters which do not have a local network
management agent.ro Counter .1.3.6.1.4.1.11.2.14.11.2.2.3.1.1.3 |
hpRptrMonPtBcastPacketsThis counter is incremented by one for each
broadcast packet of valid frame length received on
this port. This object may not be implemented for
repeaters which do not have a local network
management agent.ro Counter .1.3.6.1.4.1.11.2.14.11.2.2.3.1.1.4 |
hpRptrMonPtMcastPacketsThis counter is incremented by one for each
multicast packet of valid frame length received on
this port. This object may not be implemented for
repeaters which do not have a local network
management agent.ro Counter .1.3.6.1.4.1.11.2.14.11.2.2.3.1.1.5 |
hpRptrAddrTrack OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.2.3 |
hpRptrAddrTrkGlobal OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.2.3.1 |
hpRptrAddrTrkGroup OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.2.3.2 |
hpRptrAddrTrkPort OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.2.3.3 |
hpicfVg OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.3 |
hpVgBasic OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.3.1 |
hpVgBasicGlobal OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.3.1.1 |
hpVgEntityNameThe local name of this 100BaseVG repeater. This is
the same value as hpicfEntityName in the case where
there is Distributed Management Protocol to access
this device.
For SNMPv1, this name is appended to the agent
community name to obtain a community name to use
to specify that the agent should proxy to this
repeater. For example, if this agent has a
community with a community name of 'public', and
the value of this object is 'repeater1', the
community 'public/repeater1' will specify that the
agent should proxy to the public community of the
repeater1 box to obtain management information
about this repeater.
If an agent receives a management request where
the localEntity is not specified, it will default
to the local repeater on which this agent is
executing.ro DisplayString .1.3.6.1.4.1.11.2.14.11.3.1.1.1 |
hpVgBasicGroup OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.3.1.2 |
hpVgBasicGroupTableHP specific extensions to the vgBasicGroupTable. SEQUENCE OF HpVgBasicGroupEntry .1.3.6.1.4.1.11.2.14.11.3.1.2.1 |
hpVgBasicGroupEntryAn entry in the table, containing HP extensions
for a specific group. HpVgBasicGroupEntry .1.3.6.1.4.1.11.2.14.11.3.1.2.1.1 |
hpVgGrpGroupIndexThe group within the repeater for which this entry
contains information. This object has the same value
as the corresponding instance of icfVgGroupIndex. INTEGER .1.3.6.1.4.1.11.2.14.11.3.1.2.1.1.1 |
hpVgGrpPortsAdminStatusThe hpVgGrpPortsAdminStatus is a bit map of the
state of the icfVgPortAdminStatus object for all
of the ports in this group. The object has a one
bit for each port for which the value of
icfVgPortAdminStatus is equal to 'enabled(1)' and
a zero bit for each port for which the value of
icfVgPortAdminStatus is equal to 'disabled(2)'.
The bits are placed into the OCTET STRING in the
following order:
octet 0 octet 1 octet 2 ...
bits 7-0 bits 7-0 bits 7-0 ...
ports 1-8 ports 9-16 ports 17-24 ...
Values of unused bits in the last octet are
undefined.ro OCTET STRING .1.3.6.1.4.1.11.2.14.11.3.1.2.1.1.2 |
hpVgGrpPortsTrainedThe hpVgGrpPortsTrained is a bit map which indicates
which ports in this group are currently online. The
object has a one bit for each port for which meets
the following conditions:
1. The value of the corresponding instance of the
ifVgPortAdminStatus object is equal to
'enabled(1)'.
2. The value of the corresponding instance of the
icfVgPortStatus object is equal to 'active(1)'.
The object has a zero bit for each port which does
not meet the above conditions.
The bits are placed into the OCTET STRING in the
following order:
octet 0 octet 1 octet 2 ...
bits 7-0 bits 7-0 bits 7-0 ...
ports 1-8 ports 9-16 ports 17-24 ...
Values of unused bits in the last octet are
undefined.ro OCTET STRING .1.3.6.1.4.1.11.2.14.11.3.1.2.1.1.3 |
hpVgGrpPortsInTrainingThe hpVgGrpPortsInTraining is a bit map which
indicates which ports in this group are currently in
the training state. The object has a one bit for
each port which meets the following conditions:
1. The value of the corresponding instance of the
ifVgPortAdminStatus object is equal to
'enabled(1)'.
2. The value of the corresponding instance of the
icfVgPortStatus object is equal to
'training(3)'.
The object has a zero bit for each port which does
not meet the above conditions.
The bits are placed into the OCTET STRING in the
following order:
octet 0 octet 1 octet 2 ...
bits 7-0 bits 7-0 bits 7-0 ...
ports 1-8 ports 9-16 ports 17-24 ...
Values of unused bits in the last octet are
undefined.ro OCTET STRING .1.3.6.1.4.1.11.2.14.11.3.1.2.1.1.4 |
hpVgGrpPortsCascadedThe hpVgGrpPortsCascaded is a bit map which
indicates which ports in this group have trained as
cascaded repeater ports. The object has a one bit
for each port which meets the following conditions:
1. The value of the corresponding instance of the
ifVgPortAdminStatus object is equal to
'enabled(1)'.
2. The value of the corresponding instance of the
icfVgPortStatus object is equal to
'active(1)'.
3. The value of the corresponding instance of the
icfVgPortType object is equal to either
'normalInternal(3)' or 'normalExternal(4)'.
4. The value of the 'R' bit in the corresponding
instance of the icfVgPortTrainingResult object
is equal to one.
The object has a zero bit for each port which does
not meet the above conditions.
The bits are placed into the OCTET STRING in the
following order:
octet 0 octet 1 octet 2 ...
bits 7-0 bits 7-0 bits 7-0 ...
ports 1-8 ports 9-16 ports 17-24 ...
Values of unused bits in the last octet are
undefined.ro OCTET STRING .1.3.6.1.4.1.11.2.14.11.3.1.2.1.1.5 |
hpVgGrpPortsPromiscuousThe hpVgGrpPortsPromiscuous is a bit map which
indicates which ports in this group have trained for
promiscuous operation. The object has a one bit for
each port which meets the following conditions:
1. The value of the corresponding instance of the
ifVgPortAdminStatus object is equal to
'enabled(1)'.
2. The value of the corresponding instance of the
icfVgPortStatus object is equal to
'active(1)'.
3. The value of the corresponding instance of the
icfVgPortType object is equal to either
'normalInternal(3)' or 'normalExternal(4)'.
4. The value of the 'R' bit in the corresponding
instance of the icfVgPortTrainingResult object
is equal to zero.
5. The value of the 'PP' field in the corresponding
instance of the icfVgPortTrainingResult object
is equal to 01.
The object has a zero bit for each port which does
not meet the above conditions.
The bits are placed into the OCTET STRING in the
following order:
octet 0 octet 1 octet 2 ...
bits 7-0 bits 7-0 bits 7-0 ...
ports 1-8 ports 9-16 ports 17-24 ...
Values of unused bits in the last octet are
undefined.ro OCTET STRING .1.3.6.1.4.1.11.2.14.11.3.1.2.1.1.6 |
hpVgBasicPort OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.3.1.3 |
hpVgBasicPortTableHP specific extensions to the vg port table. SEQUENCE OF HpVgBasicPortEntry .1.3.6.1.4.1.11.2.14.11.3.1.3.1 |
hpVgBasicPortEntryHP extended information about a specific vg port. HpVgBasicPortEntry .1.3.6.1.4.1.11.2.14.11.3.1.3.1.1 |
hpVgPortGroupIndexThe group that contains the port for which this
entry contains information. INTEGER .1.3.6.1.4.1.11.2.14.11.3.1.3.1.1.1 |
hpVgPortIndexThe port within the group for which this entry
contains information. INTEGER .1.3.6.1.4.1.11.2.14.11.3.1.3.1.1.2 |
hpVgPortPolarityReversedThis object is used to indicate that the hub port
was wired with the positive/negative polarity of its
wire pairs reversed. Note that the port will
continue to operate in this state, with the hub
inverting the polarity internally.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.3.1.3.1.1.3 |
hpVgPortWireSkewErrorThis object is used to indicate that a wire skew
error has been detected on this port.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.3.1.3.1.1.4 |
hpVgMonitor OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.3.2 |
hpVgMonitorGlobal OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.3.2.1 |
hpVgMonCounters OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.3.2.1.1 |
hpVgMonGlbReadableFramesThis object is the total number of good frames of
valid frame length that have been received on all
ports in this repeater. This counter is the
summation of the values of the
icfVgPortReadableFrames counter for all of the ports
in this repeater.ro Counter .1.3.6.1.4.1.11.2.14.11.3.2.1.1.1 |
hpVgMonGlbReadableOctetsThis object is a count of the total number of octets
contained in good frames that have been received on
all ports in this repeater. This counter is the
summation of the values of the
icfVgPortReadableOctets counter for all of the ports
in this repeater.
Note that this counter may roll over very quickly.ro Counter .1.3.6.1.4.1.11.2.14.11.3.2.1.1.2 |
hpVgMonGlbUnreadableOctetsThis object is a count of the total number of octets
contained in invalid frames that have been received
on all ports in this repeater. This counter is the
summation of the values of icfVgPortUnreadableOctets
counter for all of the ports in this repeater.
Note that this counter may roll over very quickly.ro Counter .1.3.6.1.4.1.11.2.14.11.3.2.1.1.3 |
hpVgMonGlbHighPriorityFramesThis object is a count of the total number of high
priority frames that have been received on all ports
in this repeater. This counter is a summation of the
values of the icfVgPortHighPriorityFrames counter for
all of the ports in this repeater.ro Counter .1.3.6.1.4.1.11.2.14.11.3.2.1.1.4 |
hpVgMonGlbHighPriorityOctetsThis object is a count of the total number of octets
contained in high priority frames that have been
received on all ports of this repeater. This counter
is a summation of the values of the
icfVgPortHighPriorityOctets counter for all of the
ports in this repeater.
Note that this counter may roll over very quickly.ro Counter .1.3.6.1.4.1.11.2.14.11.3.2.1.1.5 |
hpVgMonGlbBroadcastFramesThis object is a count of the total number of
broadcast packets that have been received on all
ports in this repeater. This counter is a summation
of the values of the icfVgPortBroadcastFrames counter
for all of the ports in this repeater.ro Counter .1.3.6.1.4.1.11.2.14.11.3.2.1.1.6 |
hpVgMonGlbMulticastFramesThis object is a count of the total number of
multicast packets that have been received on all
ports in this repeater. This counter is a summation
of the values of the icfVgPortMulticastFrames counter
for all of the ports in this repeater.ro Counter .1.3.6.1.4.1.11.2.14.11.3.2.1.1.7 |
hpVgMonGlbIPMFramesThis object is a count of the total number of frames
that have been received on all ports in this repeater
with an invalid packet marker. This counter is a
summation of the values of the icfVgPortIPMFrames
counter for all of the ports in this repeater.ro Counter .1.3.6.1.4.1.11.2.14.11.3.2.1.1.8 |
hpVgMonGlbDataErrorFramesThis object is a count of the total number of
errored frames received on all ports in this
repeater. This counter is a summation of the values
of the icfVgPortDataErrorFrames counter for all of
the ports in this repeater.ro Counter .1.3.6.1.4.1.11.2.14.11.3.2.1.1.9 |
hpVgMonGlbPriorityPromotionsThis object is a count of the total number of
times the priority promotion timer has expired on
any port in this repeater. This counter is a
summation of the values of the
icfVgPortPriorityPromotions counter for all of the
ports in this repeater.ro Counter .1.3.6.1.4.1.11.2.14.11.3.2.1.1.10 |
hpVgMonitorGroup OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.3.2.2 |
hpVgMonitorPort OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.3.2.3 |
hpicfGenericRepeater OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.4 |
hpGRpBasic OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.4.1 |
hpGRpBasicGlobal OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.4.1.1 |
hpGRpSelfHealEnableThis flag controls whether or not the device will
send self healing packets. Self healing packets are
normally sent once per second by the agent when no
other traffic is present. When there is no traffic
present on a network, there is no way to detect
cabling problems (or the repair of cabling problems)
and status LEDs are not always correct.
Enabling this flag allows the agent to detect cabling
problems on an idle network. This flag can be
disabled if self healing packets are not wanted.
On the 100BaseVG-AnyLAN SNMP/Bridge card, these
packets are addressed to a unique unused unicast
station address which has been reserved by HP for
this purpose. On 802.3 repeaters, these packets are
self addressed.
On an 802.3 repeater, this flag MUST be enabled when
using the Robust Port Healing feature. Without
Robust Port Healing either a good transmit or a good
receive will reconnect an autopartitioned port. With
Robust Port Healing the criteria is more restrictive
and only a good transmit will heal a segmented port.
If all ports are segmented, the repeater will not
repeat anything until the agent transmits a self
healing packet and reconnects the autopartitioned
ports.rw Enumeration .1.3.6.1.4.1.11.2.14.11.4.1.1.1 |
hpGRpBasicGroup OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.4.1.2 |
hpGRpBasicPort OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.4.1.3 |
hpGRpMonitor OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.4.2 |
hpGRpAddrTrack OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.4.3 |
hpicfNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.12 |
hpicfCommonTraps OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.12.1 |
hpicfChainAdditionAn hpicfChainAddition trap indicates that a new node
has been added to the Distributed Management Chain
connected to this agent. The hpicfChainId returned
is the identifier for the new node. TRAP-TYPE .1.3.6.1.4.1.11.2.14.12.1.0.1 |
hpicfChainRemovalAn hpicfChainRemoval trap indicates that a node has
been removed from the Distributed Management Chain
connected to this agent. The hpicfChainId returned
is the identifier for the node that was removed. TRAP-TYPE .1.3.6.1.4.1.11.2.14.12.1.0.2 |
hpicf8023RptrTraps OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.12.2 |
hpicfVgRptrTraps OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.12.3 |
hpicfGenRptrTraps OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.12.4 |