HH3C-DOT11-CFG-MIB
This MIB provides information about WLAN configuration.
GLOSSARY
IEEE 802.11 Standard to encourage interoperability among wireless networking equipment.
Access point (AP) Transmitter/receiver (transceiver) device that commonly connects and transports data between a wireless network and a wired network.
Access control (AC) To control and manage multi-APs, it will bridge wireless and wired network.
Fat AP Applied in the home, SOHO and so on, and it could work independently without help from AC.
Fit AP Applied in the enterprise environment, it will work under the control and management from AC.
Control And Provisioning of Wireless Access Points Protocol The short name of protocol is CAPWAP. AC will control and manage AP by CAPWAP tunnel protocol defined by IETF. Also, a data tunnel will be set up between AC and AP.
BSS IEEE 802.11 Basic Service Set (Radio Cell). The BSS of an AP comprises of the stations directly associating with the AP.
Radio The chip set to receive and send wireless signal.
Association The service used to establish access point or station mapping and enable station invocation of the distribution system services. (Wireless clients attempt to connect to access points.)
Basic Rate A data rate that is mandatory for client devices to support in order for them to achieve successful association.
MSDU MAC Service Data Unit, it is frame format defined by
802.11.
TU It is 1,024 microseconds (ms), which is about 1 millisecond.
AKM The authentication and key management method defined by
802.11i, and which includes 802.1x and pre-shared key.
Main OID:
hh3cDot11CFG.1.3.6.1.4.1.25506.2.75.4
342
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
342 total| Object Name |
|---|
hh3cDot11CFGThis MIB provides information about WLAN configuration.
GLOSSARY
IEEE 802.11
Standard to encourage interoperability among
wireless networking equipment.
Access point (AP)
Transmitter/receiver (transceiver) device
that commonly connects and transports data
between a wireless network and a wired network.
Access control (AC)
To control and manage multi-APs, it will bridge
wireless and wired network.
Fat AP
Applied in the home, SOHO and so on, and it could
work independently without help from AC.
Fit AP
Applied in the enterprise environment, it will work
under the control and management from AC.
Control And Provisioning of Wireless Access Points Protocol
The short name of protocol is CAPWAP. AC will control
and manage AP by CAPWAP tunnel protocol defined by IETF.
Also, a data tunnel will be set up between AC and AP.
BSS
IEEE 802.11 Basic Service Set (Radio Cell). The
BSS of an AP comprises of the stations directly
associating with the AP.
Radio
The chip set to receive and send wireless signal.
Association
The service used to establish access point
or station mapping and enable station invocation
of the distribution system services.
(Wireless clients attempt to connect to
access points.)
Basic Rate
A data rate that is mandatory for client
devices to support in order for them to achieve
successful association.
MSDU
MAC Service Data Unit, it is frame format defined by
802.11.
TU
It is 1,024 microseconds (ms), which is about 1
millisecond.
AKM
The authentication and key management method defined by
802.11i, and which includes 802.1x and pre-shared key. MODULE-IDENTITY .1.3.6.1.4.1.25506.2.75.4 |
hh3cDot11GlobeConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.25506.2.75.4.1 |
hh3cDot11GlobalCountryCodeRepresents the country code for wireless network.rw OCTET STRING .1.3.6.1.4.1.25506.2.75.4.1.1 |
hh3cDot11StaKeepALiveTimerIntvlRepresents the interval of the keep alive requests sent between
AP and STA.
Default value 0 : The keep alive function is disabled.rw Unsigned32 UNITS "second" .1.3.6.1.4.1.25506.2.75.4.1.2 |
hh3cDot11StaIdleTimerIntvlRepresents the interval for which the link between AP and STA
( power-save or awake ) can be idle.rw Integer32 UNITS "second" .1.3.6.1.4.1.25506.2.75.4.1.3 |
hh3cDot11BroadcastProbeReplyRepresents enable the AP to reply broadcast probe or not.
'true' : The AP to reply broadcast probe is enabled.
'false': The AP to reply broadcast probe is disabledrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.1.4 |
hh3cDot11APScanModeRepresents the scanning mode for AP.
The following values are supported:
active - AP will actively do scan.
passive - AP will passively do scan.rw Enumeration .1.3.6.1.4.1.25506.2.75.4.1.5 |
hh3cDot11ACCtrlTunnelSecSupportRepresents what security schemes are supported for CAPWAP Control
tunnel.rw Hh3cDot11TunnelSecSchemType (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.1.6 |
hh3cDot11ACDataTunnelSecSupportRepresents what security schemes are supported for CAPWAP data
tunnel. The cleartxt is the default scheme.rw Hh3cDot11TunnelSecSchemType (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.1.7 |
hh3cDot11ACAutoAPSupportRepresents enable the auto AP functionality or not.
'true' : The auto AP functionality is enabled.
'false': The auto AP functionality is disabledrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.1.8 |
hh3cDot11AutoAPNameRepresents the name of auto AP that needs to be made persistent.
When read the value from the node, NULL value be returned.rw OCTET STRING .1.3.6.1.4.1.25506.2.75.4.1.9 |
hh3cDot11PersistentNameRepresents the new name of auto AP after being made persistent.
When read the value from the node, NULL value be returned.rw OCTET STRING .1.3.6.1.4.1.25506.2.75.4.1.10 |
hh3cDot11IntfTrapThresholdRepresents threshold of interference trap. If signal strength of
the device exceeds this threshold, corresponding trap will
be sent.rw Integer32 UNITS "dbm" .1.3.6.1.4.1.25506.2.75.4.1.11 |
hh3cDot11MonitorIntervalRepresents the monitoring interval.
Default value 0 : The monitoring functionality is changed to
real-time mode.rw Unsigned32(0 | 5..15) UNITS "minute" .1.3.6.1.4.1.25506.2.75.4.1.12 |
hh3cDot11SampleIntervalRepresents the sampling interval.
Default value 0 : The sampling functionality is disabled.rw Unsigned32(0 | 10..300) UNITS "second" .1.3.6.1.4.1.25506.2.75.4.1.13 |
hh3cDot11ChnlSwitChkIntervalRepresents the checking interval of channel switch.rw Unsigned32 .1.3.6.1.4.1.25506.2.75.4.1.14 |
hh3cDot11APUserUplimitRepresents the upper limit of user which has access to this AP.rw Unsigned32 .1.3.6.1.4.1.25506.2.75.4.1.15 |
hh3cDot11APL2IsolateEnableRepresents enable the layer2 isolation or not.
'true' : The layer2 isolation functionality is enabled.
'false': The layer2 isolation functionality is disabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.1.16 |
hh3cDot11APBSSIDSupportNumRepresents the max number of BSSID supported by Current AP.ro Integer32 .1.3.6.1.4.1.25506.2.75.4.1.17 |
hh3cDot11APLastUpdateStatTimeRepresents date and time update statistic information lately.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.1.18 |
hh3cDot11APDoSProtectEnableRepresents enable the DOS protection or not.
'true' : The DOS protection functionality is enabled.
'false': The DOS protection functionality is disabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.1.19 |
hh3cDot11MaxAPPerIfRepresents max AP number that can be connected to AC interface.rw Unsigned32 .1.3.6.1.4.1.25506.2.75.4.1.20 |
hh3cDot11SampleTimeStampRepresents the start time of current sample period.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.1.21 |
hh3cDot11UplinkTrackIdRepresents the track id of AP.
Default value 0 : The uplink track function for AP is disabled.rw Unsigned32 .1.3.6.1.4.1.25506.2.75.4.1.22 |
hh3cDot11RtCollectSwitchThis object is used to turn on/off real-time statistics collection
between AC and AP. If the value is true, hh3cDot11RtCollectIntvl will
take effect. Otherwise, hh3cDot11RglCollectIntvl will take effect.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.1.23 |
hh3cDot11RglCollectIntvlThis object represents interval to regularly collect statistics from
AC to AP.rw Integer32 UNITS "second" .1.3.6.1.4.1.25506.2.75.4.1.24 |
hh3cDot11RtCollectIntvlThis object represents interval to collect real-time statistics from
AC to AP.rw Integer32 UNITS "second" .1.3.6.1.4.1.25506.2.75.4.1.25 |
hh3cDot11AllAPCpuUsageThresholdThe CPU usage threshold for all AP.rw Integer32 .1.3.6.1.4.1.25506.2.75.4.1.26 |
hh3cDot11AllAPMemUsageThresholdThe memory usage threshold for all AP.rw Integer32 .1.3.6.1.4.1.25506.2.75.4.1.27 |
hh3cDot11AdjIntfTrapThresholdRepresents threshold of adjacent interference trap. If signal strength
of the device exceeds this threshold, corresponding trap will be sent.rw Integer32 UNITS "dbm" .1.3.6.1.4.1.25506.2.75.4.1.28 |
hh3cDot11AllAPMonitorModeRepresents what work mode for All AP.
The following values are supported:
normal, - AP will supply WLAN service.
monitor - AP will be a monitor to find attack.
hybrid - AP will supply WLAN service and Device detection is
enabled.rw Enumeration .1.3.6.1.4.1.25506.2.75.4.1.29 |
hh3cDot11GlobalApFmwUpdStateRepresents the status of version auto-update for an AP.
The following values are supported:
enable - AP version will be updated automatically.
disable - AP version will not be updated automatically.rw Enumeration .1.3.6.1.4.1.25506.2.75.4.1.30 |
hh3cDot11ACNasIDCMRepresents the NAS-ID of current AC.rw OCTET STRING .1.3.6.1.4.1.25506.2.75.4.1.31 |
hh3cDot11PolicyConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.25506.2.75.4.2 |
hh3cDot11RadioPolicyTableThe table defines the parameters for radio policy, as per
radio policy of CLI.
One radio policy could be assigned to the different radios (AP). SEQUENCE OF Hh3cDot11RadioPolicyEntry .1.3.6.1.4.1.25506.2.75.4.2.1 |
hh3cDot11RadioPolicyEntryEach entry contains information of each radio policy. Hh3cDot11RadioPolicyEntry .1.3.6.1.4.1.25506.2.75.4.2.1.1 |
hh3cDot11RadioPolicyNameRepresents the name of radio policy. OCTET STRING .1.3.6.1.4.1.25506.2.75.4.2.1.1.1 |
hh3cDot11BeaconIntervalRepresents the interval for Beacon management frame.rw Integer32 UNITS "TU" .1.3.6.1.4.1.25506.2.75.4.2.1.1.2 |
hh3cDot11DtimIntervalRepresents the number of beacon intervals that shall elapse
between transmission of Beacons frames containing a Traffic
Indication Map (TIM) element whose DTIM Count field is 0.
This value is transmitted in the Delivery TIM (DTIM) Period
field of Beacon frames.rw Integer32 .1.3.6.1.4.1.25506.2.75.4.2.1.1.3 |
hh3cDot11RtsThresholdRepresents the current minimum size, in octets, of the MAC
protocol data unit (MPDU), below which a Request to send/Clear
to send (RTS/CTS) handshake shall not be performed.rw Integer32 UNITS "byte" .1.3.6.1.4.1.25506.2.75.4.2.1.1.4 |
hh3cDot11FragThresholdRepresents the current maximum size, in octets, of the MPDU that
may be delivered to the PHY. A MSDU shall be broken into
fragments if its size exceeds the value of this attribute after
adding MAC headers and trailers.rw Integer32 UNITS "byte" .1.3.6.1.4.1.25506.2.75.4.2.1.1.5 |
hh3cDot11ShortRetryThresholdRepresents the maximum number of transmission attempts of a
frame, the length of which is less than or equal to
hh3cDot11RTSThreshold, which shall be made before a failure
condition is indicated.rw Integer32 .1.3.6.1.4.1.25506.2.75.4.2.1.1.6 |
hh3cDot11LongRetryThresholdRepresents the maximum number of transmission attempts of a
frame, the length of which is longer than hh3cDot11RTSThreshold,
that shall be made before a failure condition is indicated.rw Integer32 .1.3.6.1.4.1.25506.2.75.4.2.1.1.7 |
hh3cDot11MaxRxLifetimeRepresents the elapsed time. After the time specified by
hh3cDot11MaxRxLifetime, the further attempts to reassemble the
MSDU shall be terminated.rw Unsigned32 UNITS "millisecond" .1.3.6.1.4.1.25506.2.75.4.2.1.1.8 |
hh3cDot11RdoPolicyRowStatusThe status of this table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.2.1.1.9 |
hh3cDot11RdoClientMaxCountRepresent the maximum number of stations supported by
this radio policy.rw Integer32 .1.3.6.1.4.1.25506.2.75.4.2.1.1.10 |
hh3cDot11BeaconIntervalMsRepresents the interval for Beacon management frame.rw Integer32 UNITS "ms" .1.3.6.1.4.1.25506.2.75.4.2.1.1.11 |
hh3cDot11ServicePolicyTableThe table defines the parameters for ESS, as per service policy
of CLI.
One service policy could be assigned to the different radios
(AP). SEQUENCE OF Hh3cDot11ServicePolicyEntry .1.3.6.1.4.1.25506.2.75.4.2.2 |
hh3cDot11ServicePolicyEntryEach entry contains information of each service policy. Hh3cDot11ServicePolicyEntry .1.3.6.1.4.1.25506.2.75.4.2.2.1 |
hh3cDot11ServicePolicyIDRepresents the ID of each service policy. Hh3cDot11ServicePolicyIDType (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.2.2.1.1 |
hh3cDot11SSIDNameRepresents the ESS. As per CLI, the value of
service policy name will be SSID.rw Hh3cDot11SSIDStringType (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.2.2.1.2 |
hh3cDot11SSIDHiddenThis attribute controls whether the SSID will be advertised in
the beacon frame.
If it is true, then SSID will not be advertised in the beacon
frame.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.2.2.1.3 |
hh3cDot11AuthenModeRepresents the Authentication mode defined by 802.11.rw Hh3cDot11AuthenType (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.2.2.1.4 |
hh3cDot11SSIDEncryptionModeRepresents the encryption mode for this ESS.rw Hh3cDot11SSIDEncryptModeType (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.2.2.1.5 |
hh3cDot11WlanInfBindingTypeRepresents the service policy will bind to what kind of
data forwarding interface.rw OCTET STRING .1.3.6.1.4.1.25506.2.75.4.2.2.1.6 |
hh3cDot11WlanInfBindingIDRepresents the interface ID of the interface that ESS will
bind to.
If the value is set to -1, the binding will be removed.rw Integer32 .1.3.6.1.4.1.25506.2.75.4.2.2.1.7 |
hh3cDot11SrvPolicyRowStatusThe status of this table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.2.2.1.8 |
hh3cDot11ClientMaxCountRepresent the maximum number of stations supported by
this service policy.rw Integer32 .1.3.6.1.4.1.25506.2.75.4.2.2.1.9 |
hh3cDot11SPInCirModeCIR(committed information rate) mode of inbound direction.
This object is useful only when the corresponding CIR is nonzero.
If value of this object is changed, corresponding CIR will be reset.rw Hh3cDot11CirMode (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.2.2.1.10 |
hh3cDot11SPInCirValueRepresents the CIR of inbound direction of this service policy.
If the value is 0, it means that no flow control is applied to
the service policy, and the corresponding CIR mode is meaningless.rw Integer32 UNITS "Kbps" .1.3.6.1.4.1.25506.2.75.4.2.2.1.11 |
hh3cDot11SPOutCirModeCIR(committed information rate) mode of outbound direction.
This object is useful only when the corresponding CIR is nonzero.
If value of this object is changed, corresponding CIR will be reset.rw Hh3cDot11CirMode (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.2.2.1.12 |
hh3cDot11SPOutCirValueRepresents the CIR of outbound direction of this service policy.
If the value is 0, it means that no flow control is applied to
the service policy, and the corresponding CIR mode is meaningless.rw Integer32 UNITS "Kbps" .1.3.6.1.4.1.25506.2.75.4.2.2.1.13 |
hh3cDot11WlanInfPVIDRepresents the VLAN ID of SSID.rw Integer32 .1.3.6.1.4.1.25506.2.75.4.2.2.1.14 |
hh3cDot11SPInCirStaticValueRepresents the CIR of inbound direction for static CIR mode.rw Integer32 UNITS "Kbps" .1.3.6.1.4.1.25506.2.75.4.2.2.1.15 |
hh3cDot11SPOutCirStaticValueRepresents the CIR of outbound direction for static CIR mode.rw Integer32 UNITS "Kbps" .1.3.6.1.4.1.25506.2.75.4.2.2.1.16 |
hh3cDot11SPIsolateIf it is true, then stations connected with the service policy are
isolated.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.2.2.1.17 |
hh3cDot11WlanexAuthServerIPRepresents the IP address of the Wlanex Authentication serverrw IpAddress .1.3.6.1.4.1.25506.2.75.4.2.2.1.18 |
hh3cDot11SPBeaconMeasEnableIf it is true, then beacon-measurement is enabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.2.2.1.19 |
hh3cDot11SPBeaconMeasTypeRepresents what the work mode for BeaconMeasurement type.
The following values are supported:
passive, - BeaconMeasurement will use the passive type.
active - BeaconMeasurement will use the active type.
beaconTable - BeaconMeasurement will use the beacon table type.rw Enumeration .1.3.6.1.4.1.25506.2.75.4.2.2.1.20 |
hh3cDot11SPBeaconMeasIntervalRepresents the beacon-measurement interval.rw Integer32 .1.3.6.1.4.1.25506.2.75.4.2.2.1.21 |
hh3cDot11AuthenModeCMRepresents the Authentication mode defined by 802.11.rw Enumeration .1.3.6.1.4.1.25506.2.75.4.2.2.1.22 |
hh3cDot11SecIEStatusCMTo enable the security Information element in the beacon and
probe response frames sent by AP.rw Enumeration .1.3.6.1.4.1.25506.2.75.4.2.2.1.23 |
hh3cDot11SecurityCiphersCMThe WLAN system support the following cipher type for data frame
encryption.
none
wep40
wep104
tkip
aesccmp
wpi-SMS4
When the value of node equals to zero, it means no configuration or
undo operation.rw Enumeration .1.3.6.1.4.1.25506.2.75.4.2.2.1.24 |
hh3cDot11SrvPolicyStatusCMThe status of the Service Policy.rw Enumeration .1.3.6.1.4.1.25506.2.75.4.2.2.1.25 |
hh3cDot11SSIDHiddenCMThis attribute controls whether the SSID will be advertised in
beacon frames.
If it is dot11true, the SSID will not be advertised in beacon
frames.rw Hh3cDot11TruthValueCM (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.2.2.1.26 |
hh3cDot11SPIsolateCMIf it is dot11true, the clients connected with the service policy are
isolated to each other.rw Hh3cDot11TruthValueCM (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.2.2.1.27 |
hh3cDot11ServicePolicyExtTableThe table defines the parameters for ESS, as per service policy
of CLI.
When the value of hh3cDot11SSIDEncryptionMode equals to cipher(2),
more configuration for a ESS will be put into the table. SEQUENCE OF Hh3cDot11ServicePolicyExtEntry .1.3.6.1.4.1.25506.2.75.4.2.3 |
hh3cDot11ServicePolicyExtEntryEach entry contains information of each service policy under cipher(2)
mode. Hh3cDot11ServicePolicyExtEntry .1.3.6.1.4.1.25506.2.75.4.2.3.1 |
hh3cDot11ServicePolicyExtIDRepresents the ID of each service policy. Hh3cDot11ServicePolicyIDType (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.2.3.1.1 |
hh3cDot11SecIEStatusTo enable the security Information element in the beacon and
probe response frames sent by AP.rw Hh3cDot11SecIEStatusType (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.2.3.1.2 |
hh3cDot11SecurityCiphersThe WLAN system support the following cipher type for data frame
encryption.
wep40(2)
tkip(4)
aesccmp(16)
wep104(32)
wpisms4(64)
wep128(128)
For each service policy, it could support multiple cipher types at
the same time. So the value of object could combine multiple value
of cipher type above.
When the value of node equals to zero, it means no configuration or
undo operation.rw Integer32 .1.3.6.1.4.1.25506.2.75.4.2.3.1.3 |
hh3cDot11CipherKeyIndexRepresents the key index of cipher key for packet.
When hh3cDot11SecurityCiphers value is wep40 or wep104,
the configuration will take effective.rw Integer32 .1.3.6.1.4.1.25506.2.75.4.2.3.1.4 |
hh3cDot11CipherKeyRepresents the cipher key for packet.
When hh3cDot11SecurityCiphers value is wep40 or wep104,
the configuration will take effective.rw OCTET STRING .1.3.6.1.4.1.25506.2.75.4.2.3.1.5 |
hh3cDot11SrvPolicyExtRowStatusThe status of this table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.2.3.1.6 |
hh3cDot11CipherKeyTypeRepresents the cipher key type of hh3cDot11CipherKey.rw Enumeration .1.3.6.1.4.1.25506.2.75.4.2.3.1.7 |
hh3cDot11RadioPolicyExtTableThe table defines the radio policy of each radio.
It can't be modified if the radio policy is a default radio policy. SEQUENCE OF Hh3cDot11RadioPolicyExtEntry .1.3.6.1.4.1.25506.2.75.4.2.4 |
hh3cDot11RadioPolicyExtEntryEach entry contains information of each radio policy. Hh3cDot11RadioPolicyExtEntry .1.3.6.1.4.1.25506.2.75.4.2.4.1 |
hh3cDot11RPAPSerialIDThis object represents the Serial ID of AP. OCTET STRING .1.3.6.1.4.1.25506.2.75.4.2.4.1.1 |
hh3cDot11RPRadioIDThis object represents each radio. Hh3cDot11RadioScopeType (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.2.4.1.2 |
hh3cDot11RPBeaconIntervalThis object represents the interval for Beacon management frame.rw Integer32 UNITS "milliseconds" .1.3.6.1.4.1.25506.2.75.4.2.4.1.3 |
hh3cDot11RPDtimIntervalThis object represents the number of beacon intervals that shall elapse
between transmissions of Beacons frames containing a Traffic
Indication Map (TIM) element whose DTIM count field is 0.
This value is transmitted in the Delivery TIM (DTIM) Period
field of Beacon frames.rw Integer32 .1.3.6.1.4.1.25506.2.75.4.2.4.1.4 |
hh3cDot11RPRtsThresholdThis object represents the current minimum size, in octets, of the MAC
protocol data unit (MPDU), below which a Request to send/Clear
to send (RTS/CTS) handshake shall not be performed.rw Integer32 UNITS "byte" .1.3.6.1.4.1.25506.2.75.4.2.4.1.5 |
hh3cDot11RPFragThresholdThis object represents the current maximum size, in octets, of the MPDU
that may be delivered to the PHY. A MSDU shall be broken into
fragments if its size exceeds the value of this attribute after
adding MAC headers and trailers.rw Integer32 UNITS "byte" .1.3.6.1.4.1.25506.2.75.4.2.4.1.6 |
hh3cDot11RPShortRetryThresholdThis object represents the maximum number of transmission attempts of a
frame, the length of which is less than or equal to
hh3cDot11RTSThreshold, that shall be made before a failure
condition is indicated.rw Integer32 .1.3.6.1.4.1.25506.2.75.4.2.4.1.7 |
hh3cDot11RPLongRetryThresholdThis object represents the maximum number of transmission attempts of a
frame, the length of which is longer than hh3cDot11RTSThreshold,
and that shall be made before a failure condition is indicated.rw Integer32 .1.3.6.1.4.1.25506.2.75.4.2.4.1.8 |
hh3cDot11RPClientMaxCountThis object represents the maximum number of stations supported by
this radio policy.rw Integer32 .1.3.6.1.4.1.25506.2.75.4.2.4.1.9 |
hh3cDot11RPBeaconIntervalCMThis object represents beacon interval.rw Integer32 UNITS "timeunit" .1.3.6.1.4.1.25506.2.75.4.2.4.1.10 |
hh3cDot11SrvPortSecurityTableThis table defines the WLAN security status for ESS, BSS and
WLAN-Ethernet interface which binding the crypto service-template.
Otherwise, when binding the clear service-template,
hh3cPortSecurityTables should be used to configure port security. SEQUENCE OF Hh3cDot11SrvPortSecurityEntry .1.3.6.1.4.1.25506.2.75.4.2.5 |
hh3cDot11SrvPortSecurityEntryThere is a row in this table for service policy. Hh3cDot11SrvPortSecurityEntry .1.3.6.1.4.1.25506.2.75.4.2.5.1 |
hh3cDot11SecurityServicePolicyIDRepresents the ID of each service policy. Hh3cDot11ServicePolicyIDType (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.2.5.1.1 |
hh3cDot11SrvPortSecurityModeDetermines the security modes of the WLAN port.
noRestrictions The default value, no any security mode is set.
userLoginSecureExt Access to the port is denied until the port
client is authorized (by 802.1X).
psk Access to the port is denied until the port client is
authorized (by 802.1X key negotiation).
macAddressAndPsk The MAC address is first authenticated and only if
this succeeds does the psk then attempt user authentication.
userLoginSecureExtOrPsk This selects both the userLoginSecureExt and
psk modes together such that either is allowed to authorized access.
Which mode works for client depends on the client's choice.
ext Access to the port is denied until the port client is
authenticated (by ext).rw Enumeration .1.3.6.1.4.1.25506.2.75.4.2.5.1.2 |
hh3cDot11SrvSecurityKeyTypeThis indicates the key type in the 802.1X EAPOL_Key packet.
userLoginTxKeyTypeNone - This means the key type is not set yet.
userLoginTxKeyTypeDot11Key - This selects the 802.11 key type.
userLoginTxKeyTypeRsaRC4Key - This selects the RC4 key for RSA RC4
session encryption.rw Enumeration .1.3.6.1.4.1.25506.2.75.4.2.5.1.3 |
hh3cDot11SrvSecurityPskKeyModeThis is the password input mode. When input as pskKeyModePassPhrase,
hh3cDot11SrvSecurityPskKeyString must be 8 to 63 characters;
when input as pskKeyModeRawKey, hh3cDot11SrvSecurityPskKeyString
must be 64 characters and each character must be '0'-'9', 'a'-'f' and
'A'-'F'.rw Enumeration .1.3.6.1.4.1.25506.2.75.4.2.5.1.4 |
hh3cDot11SrvSecurityPskKeyStringThis is the password string used for psk authentication.rw DisplayString .1.3.6.1.4.1.25506.2.75.4.2.5.1.5 |
hh3cDot11SrvPortSecurityModeCMDetermines the security modes of the WLAN port.
none - The default value, no any security mode is set.
psk - Access to the port is denied until the port client is
authorized (by 802.1X key negotiation).
radius - Access to the port is denied until the port
client is authorized (by 802.1X).
wlanex - Access to the port is denied until the port client is
authenticated by wlan cert.rw Enumeration .1.3.6.1.4.1.25506.2.75.4.2.5.1.6 |
hh3cDot11SrvPolicyExtendTableThe table defines the parameters of each service policy. SEQUENCE OF Hh3cDot11SrvPolicyExtendEntry .1.3.6.1.4.1.25506.2.75.4.2.6 |
hh3cDot11SrvPolicyExtendEntryEach entry contains information of each service policy. Hh3cDot11SrvPolicyExtendEntry .1.3.6.1.4.1.25506.2.75.4.2.6.1 |
hh3cDot11SPEnableRepresents whether the service policy is enabled.rw Enumeration .1.3.6.1.4.1.25506.2.75.4.2.6.1.1 |
hh3cDot11APConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.25506.2.75.4.3 |
hh3cDot11APTemplateTableBy AP template CLI, administrator will configure the parameters of AP
by convenience.
Before AP boot up and connect to AC by CAPWAP tunnel, administrator
will create AP template for each AP. When AP connect to AC,
AC will assign configuration to AP by hh3cDot11APSerialID
information in AP template. SEQUENCE OF Hh3cDot11APTemplateEntry .1.3.6.1.4.1.25506.2.75.4.3.1 |
hh3cDot11APTemplateEntryEach entry contains configuration information for each AP. Hh3cDot11APTemplateEntry .1.3.6.1.4.1.25506.2.75.4.3.1.1 |
hh3cDot11APTemplateNameRepresents the name of AP template. OCTET STRING .1.3.6.1.4.1.25506.2.75.4.3.1.1.1 |
hh3cDot11APSerialIDRepresents AP serial id.rw OCTET STRING .1.3.6.1.4.1.25506.2.75.4.3.1.1.2 |
hh3cDot11TemplateAPModelAliasRepresents the alias of AP model name.rw OCTET STRING .1.3.6.1.4.1.25506.2.75.4.3.1.1.3 |
hh3cDot11DescriptionThis attribute will give more information about AP.
Administrator could suggest the location, owner or
other information for each AP.
If the value is set to NULL, the description will be removed.rw OCTET STRING .1.3.6.1.4.1.25506.2.75.4.3.1.1.4 |
hh3cDot11APWorkModeRepresents what work mode for AP.
The following values are supported:
normal - AP will supply WLAN service.
monitor - AP will be a monitor to find attack.
hybrid - AP will supply WLAN service and Device detection is
enabled.rw Enumeration .1.3.6.1.4.1.25506.2.75.4.3.1.1.5 |
hh3cDot11APTemplateRowStatusThe status of this table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.3.1.1.6 |
hh3cDot11APNameRepresents the AP name.rw OCTET STRING .1.3.6.1.4.1.25506.2.75.4.3.1.1.7 |
hh3cDot11StatisIntervRepresents the interval of radio statistic.rw Integer32 UNITS "second" .1.3.6.1.4.1.25506.2.75.4.3.1.1.8 |
hh3cDot11APBroadcastProbeReplyRepresents enable the AP to reply broadcast probe or not.
'true' : The AP to reply broadcast probe is enabled.
'false': The AP to reply broadcast probe is disabledrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.3.1.1.9 |
hh3cDot11StaIdleTimerIntervRepresents the interval for which the link between AP and STA
( power-save or awake ) can be idle.rw Integer32 UNITS "second" .1.3.6.1.4.1.25506.2.75.4.3.1.1.10 |
hh3cDot11StaKeepAliveTimerIntervRepresents the interval of the keep alive requests sent between
AP and STA.rw Integer32 UNITS "second" .1.3.6.1.4.1.25506.2.75.4.3.1.1.11 |
hh3cDot11APCirRepresents the committed information rate between AP and AC.rw Integer32 UNITS "Kbps" .1.3.6.1.4.1.25506.2.75.4.3.1.1.12 |
hh3cDot11APCbsRepresents the committed burst size between AP and AC.rw Integer32 UNITS "Bytes" .1.3.6.1.4.1.25506.2.75.4.3.1.1.13 |
hh3cDot11APPriorityLevelThis object represents the connection priority for the AP.
If the connection priority is 7, the AC is considered as the
primary AC for the AP.rw Integer32 .1.3.6.1.4.1.25506.2.75.4.3.1.1.14 |
hh3cDot11APElementIDThis object represents the AP element ID.ro Integer32 .1.3.6.1.4.1.25506.2.75.4.3.1.1.15 |
hh3cDot11APDevDetectEnableRepresents whether device detection is enabled or not.
'true' : Device detection is enabled.
'false': Device detection is disabled.
If device detection is enabled, the AP will provide both device
detection and WLAN data services.
By default, the AP only provides WLAN data services. When an AP works
in monitor mode, that is, the value of object hh3cDot11APWorkMode is
monitor, device detection can not be enabled with object
hh3cDot11APDevDetectEnable.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.3.1.1.16 |
hh3cDot11APGetIPMethodThis object represents the method how AP gets IP address.rw Enumeration .1.3.6.1.4.1.25506.2.75.4.3.1.1.17 |
hh3cDot11StatisIntervModeThis object represents the mode of statics interval.
normal - statics interval value between 10s to 120s
realtime - statics interval value between 2s to 5srw Enumeration .1.3.6.1.4.1.25506.2.75.4.3.1.1.18 |
hh3cDot11ApTrapEnabledRepresents whether the trap status is enabled or not.
'true' : Enable the trap status;
'false' : Disable the trap status.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.3.1.1.19 |
hh3cDot11ApFmwUpdStateRepresents the status of version auto-update for an AP.
The following values are supported:
enable - AP version will be updated automatically.
disable - AP version will not be updated automatically.
inherit - The status will inherit value from apgroup-view or system-view.rw Enumeration .1.3.6.1.4.1.25506.2.75.4.3.1.1.20 |
hh3cDot11StatisIntervModeCMThis object represents the mode of statistic interval.
off - statistic interval value between 10s to 120s
on - statistic interval value between 2s to 5srw Enumeration .1.3.6.1.4.1.25506.2.75.4.3.1.1.21 |
hh3cDot11ApNasIDCMRepresents the NAS-ID of current service policy for each
specific radio of AP.rw OCTET STRING .1.3.6.1.4.1.25506.2.75.4.3.1.1.22 |
hh3cDot11RadioToConfigTableBefore AP connects to AC, administrator will configure radio
parameter to each radio. SEQUENCE OF Hh3cDot11RadioToConfigEntry .1.3.6.1.4.1.25506.2.75.4.3.2 |
hh3cDot11RadioToConfigEntryEach entry contains configuration information for each radio. Hh3cDot11RadioToConfigEntry .1.3.6.1.4.1.25506.2.75.4.3.2.1 |
hh3cDot11APTemplateNameCfgRepresents the name of AP template. OCTET STRING .1.3.6.1.4.1.25506.2.75.4.3.2.1.1 |
hh3cDot11CfgRadioIDRepresents each radio. Hh3cDot11RadioScopeType (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.3.2.1.2 |
hh3cDot11CfgRadioPolicyNameRepresents the name of radio policy.rw OCTET STRING .1.3.6.1.4.1.25506.2.75.4.3.2.1.3 |
hh3cDot11CfgRadioTypeRepresents the radio will work with which 802.11 radio type.rw Hh3cDot11RadioType (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.3.2.1.4 |
hh3cDot11CfgChannelRepresents the channel allocation of radio.rw Hh3cDot11ChannelScopeType (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.3.2.1.5 |
hh3cDot11CfgMaxTxPowerLevelRepresents the maximal transmit power scope for AP.rw Hh3cDot11TxPwrLevelScopeType UNITS "dbm" .1.3.6.1.4.1.25506.2.75.4.3.2.1.6 |
hh3cDot11PreambleLenRepresents whether use long or short preamble for 802.11 MAC
frame.
When hh3cDot11CfgRadioType is either dot11b or dot11g,
then value for hh3cDot11PreambleLen will be valid.
Otherwise, the value for it will be invalid.rw Hh3cDot11PreambleType (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.3.2.1.7 |
hh3cDot11CfgRadioStatusRepresents the radio admin status whether is enabled
or disabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.3.2.1.8 |
hh3cDot11CfgRdElementIDRepresents the element ID of this radio. It comprises two parts.
The highest 24 bits are AP element ID and the lowest 8 bits are
radio ID.ro Unsigned32 .1.3.6.1.4.1.25506.2.75.4.3.2.1.9 |
hh3cDot11CfgWorkModeRepresents work mode of the radio.rw Hh3cDot11WorkMode (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.3.2.1.10 |
hh3cDot11CfgPwrAttValueRepresents the value of power attenuation.rw Integer32 .1.3.6.1.4.1.25506.2.75.4.3.2.1.11 |
hh3cDot11RadioTxArithmeticRepresents the transmission arithmetic of the radio.
The following values are supported:
quality - Consider the quality first during the transmission.
bandwidth - Consider the bandwidth first during the transmission.rw Enumeration .1.3.6.1.4.1.25506.2.75.4.3.2.1.12 |
hh3cDot11CfgChannelLockStatRepresents locked status of channel on the radio.rw Enumeration .1.3.6.1.4.1.25506.2.75.4.3.2.1.13 |
hh3cDot11CfgPowerLockStatRepresents locked status of power on the radio.rw Enumeration .1.3.6.1.4.1.25506.2.75.4.3.2.1.14 |
hh3cDot11CfgLBRdGroupIdRepresents the load balance group ID allocated for the radio.rw Unsigned32 .1.3.6.1.4.1.25506.2.75.4.3.2.1.15 |
hh3cDot11CfgRRMSDRdGroupIdRepresents the RRM self-decisive group ID allocated for the radio.rw Unsigned32 .1.3.6.1.4.1.25506.2.75.4.3.2.1.16 |
hh3cDot11CfgRadioType2Represents the radio will work with which 802.11 radio type.rw Hh3cDot11RadioType2 (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.3.2.1.17 |
hh3cDot11CfgIDSEnableRepresents whether intrusion detection is enabled for this radio.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.3.2.1.18 |
hh3cDot11CfgSaEnableRepresents whether spectrum analysis is enabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.3.2.1.19 |
hh3cDot11CfgSaCltRtFFTDataRepresents whether to collect real-time FFT data for this radio.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.3.2.1.20 |
hh3cDot11CfgSaBandRepresents which band of channels will be monitored when collection
real-time FFT data is enabled for this radio. Detection of
interference devices and air quality will also be affected. Each band
responds to the following channels.
dot11g (Channels 1-14)
dot11aLower (channels 36-64)
dot11aMiddle (channels 100-140)
dot11aUpper (channels 149-165).rw Enumeration .1.3.6.1.4.1.25506.2.75.4.3.2.1.21 |
hh3cDot11APServiceSetTableFor each radio, it could configure multiple service policies.
The table describes the relationship between radio and
service policies. SEQUENCE OF Hh3cDot11APServiceSetEntry .1.3.6.1.4.1.25506.2.75.4.3.3 |
hh3cDot11APServiceSetEntryEach entry contains service policy information for each
specific radio of AP. Hh3cDot11APServiceSetEntry .1.3.6.1.4.1.25506.2.75.4.3.3.1 |
hh3cDot11CfgServicePolicyIDRepresents the ID of each service policy used by the AP. Hh3cDot11ServicePolicyIDType (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.3.3.1.1 |
hh3cDot11SrvSetRowStatusThe status of this table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.3.3.1.2 |
hh3cDot11ServiceSetVlanIdRepresents the Vlan ID of BSS which is generated when service policy
is binded with the Radio.rw Integer32 .1.3.6.1.4.1.25506.2.75.4.3.3.1.3 |
hh3cDot11APSysInfoSetTableThe table of the system information for each AP. SEQUENCE OF Hh3cDot11APSysInfoSetEntry .1.3.6.1.4.1.25506.2.75.4.3.4 |
hh3cDot11APSysInfoSetEntryThe system information configuration for each AP. Hh3cDot11APSysInfoSetEntry .1.3.6.1.4.1.25506.2.75.4.3.4.1 |
hh3cDot11APSysNetIDRepresents the system Net ID for AP.rw OCTET STRING .1.3.6.1.4.1.25506.2.75.4.3.4.1.1 |
hh3cDot11APCpuUsageThresholdThe CPU usage threshold for AP.rw Integer32 .1.3.6.1.4.1.25506.2.75.4.3.4.1.2 |
hh3cDot11APMemUsageThresholdThe memory usage threshold for AP.rw Integer32 .1.3.6.1.4.1.25506.2.75.4.3.4.1.3 |
hh3cDot11APLimitTableFor each connected APs, administrator could configure a series of
limits. This table describes the limit information for AP(s). SEQUENCE OF Hh3cDot11APLimitEntry .1.3.6.1.4.1.25506.2.75.4.3.5 |
hh3cDot11APLimitEntryEach entry contains the limit information for each AP. Hh3cDot11APLimitEntry .1.3.6.1.4.1.25506.2.75.4.3.5.1 |
hh3cDot11APSsidNumLimitRepresents the upper limit of service template binded
with this AP. All radios of AP share this limit.
Default value 0 : There is no upper limit of service template
binded with this AP.rw Integer32 .1.3.6.1.4.1.25506.2.75.4.3.5.1.1 |
hh3cDot11APUserCntLimitRepresents the upper limit of user which has access to this AP.
All BSSs binded with AP share this limit.
Default value 0 : There is no upper limit of user which has access
to this AP.rw Integer32 .1.3.6.1.4.1.25506.2.75.4.3.5.1.2 |
hh3cDot11APUserThresholdRepresents the threshold of user which has access to this
AP. All BSSs binded with AP share this limit. If the user counter
is overflow, the trap will be sent.
Default value 0 : There is no threshold of user which has access
to this AP.rw Integer32 .1.3.6.1.4.1.25506.2.75.4.3.5.1.3 |
hh3cDot11APIfSetTableThe table of the interface information for each AP. SEQUENCE OF Hh3cDot11APIfSetEntry .1.3.6.1.4.1.25506.2.75.4.3.6 |
hh3cDot11APIfSetEntryThe interface information configuration for each AP. Hh3cDot11APIfSetEntry .1.3.6.1.4.1.25506.2.75.4.3.6.1 |
hh3cDot11APSetIfIndexRepresents the index for a interface. Integer32 .1.3.6.1.4.1.25506.2.75.4.3.6.1.1 |
hh3cDot11APIfAliasThis object is an 'alias' name for the interface as specified
by a network manager for AP.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.3.6.1.2 |
hh3cDot11APServiceVlanTableFor all the radios on the AP, it could configure multiple service policies.
The table describes the relationship between AP and
service policies. SEQUENCE OF Hh3cDot11APServiceVlanEntry .1.3.6.1.4.1.25506.2.75.4.3.7 |
hh3cDot11APServiceVlanEntryEach entry contains service policy information for each AP. Hh3cDot11APServiceVlanEntry .1.3.6.1.4.1.25506.2.75.4.3.7.1 |
hh3cDot11APServiceVlanSerialIDThis object represents AP serial id. OCTET STRING .1.3.6.1.4.1.25506.2.75.4.3.7.1.1 |
hh3cDot11APServiceVlanSPIDThis object represents the ID of each service policy used by the AP. Hh3cDot11ServicePolicyIDType (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.3.7.1.2 |
hh3cDot11APServiceVlanIdThis object represents the VLAN ID of BSS which is generated when the
service policy is bound to the radio.rw Integer32 .1.3.6.1.4.1.25506.2.75.4.3.7.1.3 |
hh3cDot11APServiceVlanRowStatusThis object represents the status of this table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.3.7.1.4 |
hh3cDot11RadioConfigTableBefore AP connects to AC, administrator will configure radio
parameter to each radio. SEQUENCE OF Hh3cDot11RadioConfigEntry .1.3.6.1.4.1.25506.2.75.4.3.8 |
hh3cDot11RadioConfigEntryEach entry contains configuration information for each radio. Hh3cDot11RadioConfigEntry .1.3.6.1.4.1.25506.2.75.4.3.8.1 |
hh3cDot11RCAPSerialIDThis object represents the Serial ID of AP. OCTET STRING .1.3.6.1.4.1.25506.2.75.4.3.8.1.1 |
hh3cDot11RCRadioIDThis object represents each radio. Hh3cDot11RadioScopeType (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.3.8.1.2 |
hh3cDot11RCRadioTypeThis object represents the radio will work with which 802.11 radio
type.rw Hh3cDot11RadioType (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.3.8.1.3 |
hh3cDot11RCChannelThis object represents the channel allocation of radio.rw Hh3cDot11ChannelScopeType (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.3.8.1.4 |
hh3cDot11RCPreambleLenThis object represents whether use long or short preamble for 802.11
MAC frame.
When hh3cDot11CfgRadioType is either dot11b or dot11g,
then value for hh3cDot11PreambleLen will be valid.
Otherwise, the value for it will be invalid.rw Hh3cDot11PreambleType (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.3.8.1.5 |
hh3cDot11RCPwrAttValueThis object represents the value of power attenuation.rw Integer32 .1.3.6.1.4.1.25506.2.75.4.3.8.1.6 |
hh3cDot11RCApPowerLevelRepresents the maximal transmit power scope for AP.rw Hh3cDot11TxPwrLevelScopeType UNITS "dbm" .1.3.6.1.4.1.25506.2.75.4.3.8.1.7 |
hh3cDot11RCDynamicChlStateEnable/Disable dynamic channel selection.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.3.8.1.8 |
hh3cDot11RCDynamicPowerStateEnable/Disable dynamic power selection for the band.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.3.8.1.9 |
hh3cDot11RCRadioStatusRepresents the radio admin status whether is enabled
or disabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.3.8.1.10 |
hh3cDot11RCRadioRateSet data transmit rates for the radio, in the format of 1,2,5.5...
For 802.11n radios, the format can be MCS X. The data transmit rates
between AP and STA must fall into the configured rates.
(Note: For 802.11n radios, the first value will be treated as a mandatory rate,
and the second value will be treated as a supported rate.
If you configure more than two rates, the configuration cannot take effect.
If you configure only one rate, it is considered as the mandatory rate by default.)rw OCTET STRING .1.3.6.1.4.1.25506.2.75.4.3.8.1.11 |
hh3cDot11RCPwrAdjustStepLengthPower adjustment step-length in dBm.ro Integer32 .1.3.6.1.4.1.25506.2.75.4.3.8.1.12 |
hh3cDot11RCRadioType2This object represents the radio will work with which 802.11 radio
type.rw Hh3cDot11RadioType2 (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.3.8.1.13 |
hh3cDot11RCPreambleLenCMThis object represents whether use long or short preamble for 802.11
MAC frame.
When hh3cDot11CfgRadioType is either dot11b or dot11g,
then value for hh3cDot11PreambleLenCM will be valid.
Otherwise, the value for it will be invalid.rw Enumeration .1.3.6.1.4.1.25506.2.75.4.3.8.1.14 |
hh3cDot11RCDynamicChlStateCMEnable/Disable dynamic channel selection.rw Enumeration .1.3.6.1.4.1.25506.2.75.4.3.8.1.15 |
hh3cDot11RCRadioStatusCMRepresents the radio admin status whether is enabled
or disabled.rw Enumeration .1.3.6.1.4.1.25506.2.75.4.3.8.1.16 |
hh3cDot11RCRadioRateCMSet data transmit rates for the radio, in the format of 1,2,5.5...
For 802.11n radios, the format of each value can be MCS X. The data transmit
rates between AP and client should be one of the configured rates.
(Note: For 802.11n radios, the first value is mandatory rate, and the second
value is supported rate. If more than two rate values are configured, the
configuration will not take effect. If only one rate value is configured,
the mandatory rate will be set to the default value.)rw OCTET STRING .1.3.6.1.4.1.25506.2.75.4.3.8.1.17 |
hh3cDot11RCDynamicPowerStateCMEnable/disable dynamic power selection for the band.rw Hh3cDot11TruthValueCM (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.3.8.1.18 |
hh3cDot11RCRssiThresholdCMRepresents the minimum value of the RSSI.
The clients with RSSI below this value will be refused to associate.rw Integer32 UNITS "dBm" .1.3.6.1.4.1.25506.2.75.4.3.8.1.19 |
hh3cDot11RadioSSIDCfgTableFor each radio, it could configure multiple service policies.
The table describes the relationship between radio and
service policies. SEQUENCE OF Hh3cDot11RadioSSIDCfgEntry .1.3.6.1.4.1.25506.2.75.4.3.9 |
hh3cDot11RadioSSIDCfgEntryEach entry contains SSID configuration information for each radio. Hh3cDot11RadioSSIDCfgEntry .1.3.6.1.4.1.25506.2.75.4.3.9.1 |
hh3cDot11RadioSSIDSerialIDThis object represents the serial ID of AP. Hh3cDot11ObjectIDType (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.3.9.1.1 |
hh3cDot11RadioSSIDRadioIDThis object represents each radio. Hh3cDot11RadioScopeType (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.3.9.1.2 |
hh3cDot11RadioSSIDWLANIDThis object represents the WLAN ID of the BSSID. Integer32 .1.3.6.1.4.1.25506.2.75.4.3.9.1.3 |
hh3cDot11RadioSSIDIndexThis object represents the ID of each service policy used by the
radio.rw Hh3cDot11ServicePolicyIDType (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.3.9.1.4 |
hh3cDot11RadioBSSIDAs MAC address format, it is used to identify BSS.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.3.9.1.5 |
hh3cDot11RadioSSIDRowStatusRowStatus.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.3.9.1.6 |
hh3cDot11APSerialIDTableThe table will provide the general information about APs. SEQUENCE OF Hh3cDot11APSerialIDEntry .1.3.6.1.4.1.25506.2.75.4.3.10 |
hh3cDot11APSerialIDEntryEach entry contains the general information of an AP. Hh3cDot11APSerialIDEntry .1.3.6.1.4.1.25506.2.75.4.3.10.1 |
hh3cDot11SIDAPSerialIDRepresents AP serial id. OCTET STRING .1.3.6.1.4.1.25506.2.75.4.3.10.1.1 |
hh3cDot11SIDAPWorkModeRepresents what work mode for AP.
The following values are supported:
normal - AP will supply WLAN service.
monitor - AP will be a monitor to find attack.
hybrid - AP will supply WLAN service and Device detection is
enabled.rw Enumeration .1.3.6.1.4.1.25506.2.75.4.3.10.1.2 |
hh3cDot11SIDAPGetIPMethodThis object represents the method how AP gets IP address.rw Enumeration .1.3.6.1.4.1.25506.2.75.4.3.10.1.3 |
hh3cDot11SIDAPTemplateNameRepresents the name of AP template.rw OCTET STRING .1.3.6.1.4.1.25506.2.75.4.3.10.1.4 |
hh3cDot11SIDModelAliasRepresents the alias of AP model name.rw OCTET STRING .1.3.6.1.4.1.25506.2.75.4.3.10.1.5 |
hh3cDot11SIDAPDescriptionThis attribute will give more information about AP.
Administrator could suggest the location, owner or
other information for each AP.
If the value is set to NULL, the description will be removed.rw OCTET STRING .1.3.6.1.4.1.25506.2.75.4.3.10.1.6 |
hh3cDot11SIDRowStatusThe status of this table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.3.10.1.7 |
hh3cDot11SIDAPNameRepresents the AP name.rw OCTET STRING .1.3.6.1.4.1.25506.2.75.4.3.10.1.8 |
hh3cDot11SIDStatisIntervRepresents the interval of radio statistic.rw Integer32 UNITS "second" .1.3.6.1.4.1.25506.2.75.4.3.10.1.9 |
hh3cDot11SIDAPBroadcastProbeReplyRepresents enable the AP to reply broadcast probe or not.
'true' : The AP to reply broadcast probe is enabled.
'false': The AP to reply broadcast probe is disabledrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.3.10.1.10 |
hh3cDot11SIDAPStaIdleTimerIntervRepresents the interval for which the link between AP and STA
( power-save or awake ) can be idle.rw Integer32 UNITS "second" .1.3.6.1.4.1.25506.2.75.4.3.10.1.11 |
hh3cDot11SIDStaKeepAliveTimerIntervRepresents the interval of the keep alive requests sent between
AP and STA.rw Integer32 UNITS "second" .1.3.6.1.4.1.25506.2.75.4.3.10.1.12 |
hh3cDot11SIDAPCirRepresents the committed information rate between AP and AC.rw Integer32 UNITS "Kbps" .1.3.6.1.4.1.25506.2.75.4.3.10.1.13 |
hh3cDot11SIDAPCbsRepresents the committed burst size between AP and AC.rw Integer32 UNITS "Bytes" .1.3.6.1.4.1.25506.2.75.4.3.10.1.14 |
hh3cDot11SIDAPPriorityLevelThis object represents the connection priority for the AP.
If the connection priority is 7, the AC is considered as the
primary AC for the AP.rw Integer32 .1.3.6.1.4.1.25506.2.75.4.3.10.1.15 |
hh3cDot11SIDAPElementIDThis object represents the AP element ID.ro Integer32 .1.3.6.1.4.1.25506.2.75.4.3.10.1.16 |
hh3cDot11SIDAPDevDetectEnableRepresents whether device detection is enabled or not.
'true' : Device detection is enabled.
'false': Device detection is disabled.
If device detection is enabled, the AP will provide both device
detection and WLAN data services.
By default, the AP only provides WLAN data services. When an AP works
in monitor mode, that is, the value of object hh3cDot11APWorkMode is
monitor, device detection can not be enabled with object
hh3cDot11SIDAPDevDetectEnable.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.3.10.1.17 |
hh3cDot11SIDAPStatisIntervModeThis object represents the mode of statics interval.
normal - statics interval value between 10s to 120s
realtime - statics interval value between 2s to 5srw Enumeration .1.3.6.1.4.1.25506.2.75.4.3.10.1.18 |
hh3cDot11SIDAPWorkModeCMRepresents what work mode for AP.
The following values are supported:
normal - AP will supply WLAN service.
monitor - AP will be a monitor to find attack.
SemiMonitor - AP will supply WLAN service and Device detection is
enabled.rw Enumeration .1.3.6.1.4.1.25506.2.75.4.3.10.1.19 |
hh3cDot11APSTVlanTableFor each service policy, it could be bind to several VLANs.
The table describes the relationship between VLAN and
service policies. SEQUENCE OF Hh3cDot11APSTVlanEntry .1.3.6.1.4.1.25506.2.75.4.3.11 |
hh3cDot11APSTVlanEntryEach entry contains VLAN and service policy information for each
specific radio of AP. Hh3cDot11APSTVlanEntry .1.3.6.1.4.1.25506.2.75.4.3.11.1 |
hh3cDot11CfgSTVLANIDRepresents the VLAN that current Service Policy have bind to.rw Integer32 .1.3.6.1.4.1.25506.2.75.4.3.11.1.1 |
hh3cDot11CfgSTNASPortIDRepresents the NAS Port ID of current Service Policy for each
specific radio of AP.ro OCTET STRING .1.3.6.1.4.1.25506.2.75.4.3.11.1.2 |
hh3cDot11CfgServiceSetRowStatusThe status of this table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.3.11.1.3 |
hh3cDot11CfgSTNASIDRepresents the NAS ID of current Service Policy for each
specific radio of AP.ro OCTET STRING .1.3.6.1.4.1.25506.2.75.4.3.11.1.4 |
hh3cDot11RadioIntfConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.25506.2.75.4.4 |
hh3cDot11RadioIntfConfigTableThe table defines the parameters for radio in AP, as per
radio. SEQUENCE OF Hh3cDot11RadioIntfConfigEntry .1.3.6.1.4.1.25506.2.75.4.4.1 |
hh3cDot11RadioIntfConfigEntryEach entry contains information of each radio in AP. Hh3cDot11RadioIntfConfigEntry .1.3.6.1.4.1.25506.2.75.4.4.1.1 |
hh3cDot11RadioIfIdxRepresents the Radio IfIndex of radio in AP. Integer32 .1.3.6.1.4.1.25506.2.75.4.4.1.1.1 |
hh3cDot11RadioCfgBeaconIntvlRepresents the interval for Beacon management frame.rw Integer32 UNITS "TU" .1.3.6.1.4.1.25506.2.75.4.4.1.1.2 |
hh3cDot11RadioCfgDtimIntvlRepresents the number of beacon intervals that shall elapse
between transmission of Beacons frames containing a Traffic
Indication Map (TIM) element whose DTIM Count field is 0.
This value is transmitted in the Delivery TIM (DTIM) Period
field of Beacon frames.rw Integer32 .1.3.6.1.4.1.25506.2.75.4.4.1.1.3 |
hh3cDot11RadioCfgRtsThresholdRepresents the current minimum size,in octets,of the MAC
protocol data unit (MPDU), below which a Request to send/Clear
to send (RTS/CTS) handshake shall not be performed.rw Integer32 UNITS "Byte" .1.3.6.1.4.1.25506.2.75.4.4.1.1.4 |
hh3cDot11RadioCfgFragThresholdRepresents the current maximum size, in octets, of the MPDU that
may be delivered to the PHY. A MSDU shall be broken into
fragments if its size exceeds the value of this attribute after
adding MAC headers and trailers.rw Integer32 UNITS "Byte" .1.3.6.1.4.1.25506.2.75.4.4.1.1.5 |
hh3cDot11RadioCfgShtRetryThldRepresents the maximum number of transmission attempts of a
frame, the length of which is less than or equal to
hh3cDot11RadioRTSThreshold, that shall be made before a failure
condition is indicated.rw Integer32 .1.3.6.1.4.1.25506.2.75.4.4.1.1.6 |
hh3cDot11RadioCfglongRtrThldRepresents the maximum number of transmission attempts of a
frame, the length of which is longer than
hh3cDot11RadioRTSThreshold, that shall be made before a
failure condition is indicated.rw Integer32 .1.3.6.1.4.1.25506.2.75.4.4.1.1.7 |
hh3cDot11RadioCfgMaxRxLifetimeRepresents the elapsed time. After the time specified by
hh3cDot11RadioCfgMaxRxLifetime, the further attempts to reassemble
the MSDU shall be terminated.rw Unsigned32 UNITS "millisecond" .1.3.6.1.4.1.25506.2.75.4.4.1.1.8 |
hh3cDot11RadioCfgTypeRepresents the radio will work with which 802.11 radio type.rw Hh3cDot11RadioType (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.4.1.1.9 |
hh3cDot11RadioCfgChannelRepresents the channel allocation of radio.rw Hh3cDot11ChannelScopeType (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.4.1.1.10 |
hh3cDot11RadioCfgMaxTxPwrLvlRepresents the maximal transmit power scope for AP.rw Hh3cDot11TxPwrLevelScopeType UNITS "dbm" .1.3.6.1.4.1.25506.2.75.4.4.1.1.11 |
hh3cDot11RadioCfgPreambleLenRepresents whether use long or short preamble for 802.11 MAC
frame.rw Hh3cDot11PreambleType (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.4.1.1.12 |
hh3cDot11RadioCfgWorkModeRepresents work mode of the radio.rw Hh3cDot11WorkMode (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.4.1.1.13 |
hh3cDot11RadioCfgOnly11gEnableRepresents whether enable only 802.11g radio mode or not.
'true' : Only 802.11g radio mode is enabled.
'false': Only 802.11g radio mode is disabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.4.1.1.14 |
hh3cDot11RadioCfgType2Represents the radio will work with which 802.11 radio type.rw Hh3cDot11RadioType2 (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.4.1.1.15 |
hh3cDot11RadioCfgRssithresholdCMRepresents the minimum value of the RSSI.
The clients with RSSI below this value will be refused to associate.rw Integer32 UNITS "dBm" .1.3.6.1.4.1.25506.2.75.4.4.1.1.16 |
hh3cDot11RadioIntfBindTableThe table defines the binding information for each radio in AP. SEQUENCE OF Hh3cDot11RadioIntfBindEntry .1.3.6.1.4.1.25506.2.75.4.4.2 |
hh3cDot11RadioIntfBindEntryEach entry contains the radio interface binding information
in AP. Hh3cDot11RadioIntfBindEntry .1.3.6.1.4.1.25506.2.75.4.4.2.1 |
hh3cDot11RadioIntfBindSvcPlcyIDRepresents the ID of each service policy. Hh3cDot11ServicePolicyIDType (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.4.2.1.1 |
hh3cDot11RadioIntfBindIfIdxRepresents the Ifindex of interface which is binded to
the radio.rw Unsigned32 .1.3.6.1.4.1.25506.2.75.4.4.2.1.2 |
hh3cDot11RadioIntfBindRowStatusThe status of this table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.4.2.1.3 |
hh3cDot11DataRateConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.25506.2.75.4.5 |
hh3cDot11DataRateConfigTableTable will provide data rate configuration for a specific radio type. SEQUENCE OF Hh3cDot11DataRateConfigEntry .1.3.6.1.4.1.25506.2.75.4.5.1 |
hh3cDot11DataRateConfigEntryEach entry of the table will provide data rate configuration for a
specific radio type. Hh3cDot11DataRateConfigEntry .1.3.6.1.4.1.25506.2.75.4.5.1.1 |
hh3cDot11RadioTypeIDRepresents the radio type. Hh3cDot11RadioType (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.5.1.1.1 |
hh3cDot11SupportedRateSetRepresents the supported rate set of a particular radio type.rw OCTET STRING .1.3.6.1.4.1.25506.2.75.4.5.1.1.2 |
hh3cDot11MandatoryRateSetRepresents the mandatory rate set of a particular radio type.rw OCTET STRING .1.3.6.1.4.1.25506.2.75.4.5.1.1.3 |
hh3cDot11DisabledRateSetRepresents the disabled rate set of a particular radio type.rw OCTET STRING .1.3.6.1.4.1.25506.2.75.4.5.1.1.4 |
hh3cDot11SmartRateSetRepresents the rate set of a particular radio type.rw OCTET STRING .1.3.6.1.4.1.25506.2.75.4.5.1.1.5 |
hh3cDot11InterfaceConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.25506.2.75.4.6 |
hh3cDot11WlanEssIfTableThis table is used to configure WLAN ESS interface. SEQUENCE OF Hh3cDot11WlanEssIfEntry .1.3.6.1.4.1.25506.2.75.4.6.1 |
hh3cDot11WlanEssIfEntryEach entry contains the WLAN ESS interface configuration. Hh3cDot11WlanEssIfEntry .1.3.6.1.4.1.25506.2.75.4.6.1.1 |
hh3cDot11WlanEssIfNumberThis node represents the WLAN ESS interface number. Integer32 .1.3.6.1.4.1.25506.2.75.4.6.1.1.1 |
hh3cDot11WlanEssIfIndexThis node represents the ifIndex of WLAN-ESS interface.ro Integer32 .1.3.6.1.4.1.25506.2.75.4.6.1.1.2 |
hh3cDot11WlanEssRowStatusThis node represents the WLAN ESS interface row status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.6.1.1.3 |
hh3cDot11WlanBssIfTableThis table is used to configure WLAN BSS interface. SEQUENCE OF Hh3cDot11WlanBssIfEntry .1.3.6.1.4.1.25506.2.75.4.6.2 |
hh3cDot11WlanBssIfEntryEach entry contains the WLAN BSS interface configuration. Hh3cDot11WlanBssIfEntry .1.3.6.1.4.1.25506.2.75.4.6.2.1 |
hh3cDot11WlanBssIfNumberThis node represents the WLAN BSS interface number. Integer32 .1.3.6.1.4.1.25506.2.75.4.6.2.1.1 |
hh3cDot11WlanBssIfIndexThis node represents the ifIndex of WLAN-BSS interface.ro Integer32 .1.3.6.1.4.1.25506.2.75.4.6.2.1.2 |
hh3cDot11WlanBssRowStatusThis node represents the WLAN BSS interface row status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.6.2.1.3 |
hh3cDot11WLANEthernetIfTableThis table is used to configure WLAN Ethernet interface. SEQUENCE OF Hh3cDot11WLANEthernetIfEntry .1.3.6.1.4.1.25506.2.75.4.6.3 |
hh3cDot11WLANEthernetIfEntryEach entry contains the WLAN Ethernet interface configuration. Hh3cDot11WLANEthernetIfEntry .1.3.6.1.4.1.25506.2.75.4.6.3.1 |
hh3cDot11WlanEthernetIfNumberThis node represents the WLAN Ethernet interface number. Integer32 .1.3.6.1.4.1.25506.2.75.4.6.3.1.1 |
hh3cDot11WLANEthernetIfIndexThis node represents the ifIndex of WLAN-Ethernet interface.ro Integer32 .1.3.6.1.4.1.25506.2.75.4.6.3.1.2 |
hh3cDot11WlanEthernetRowStatusThis node represents the Wlan Ethernet interface row status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.6.3.1.3 |
hh3cDot11PortSecurityTableThis table defines the WLAN security status for ESS, BSS, mesh and
WLAN-Ethernet interface which binding the crypto service-template.
Otherwise, when binding the clear service-template,
hh3cPortSecurityTables should be used to configure port security. SEQUENCE OF Hh3cDot11PortSecurityEntry .1.3.6.1.4.1.25506.2.75.4.6.4 |
hh3cDot11PortSecurityEntryThere is a row in this table for each ESS, BSS and WLAN-Ethernet
interface.It is indexed using the object ifIndex in RFC1213-MIB. Hh3cDot11PortSecurityEntry .1.3.6.1.4.1.25506.2.75.4.6.4.1 |
hh3cDot11PortSecurityModeDetermines the security modes of the WLAN port.
noRestrictions - The default value,no any security mode is set.
userLoginSecureExt - Access to the port is denied until the port
client is authorized (by 802.1X).
psk - Access to the port is denied until the port client is
authorized (by 802.1X key negotiation).
macAddressAndPsk - The MAC address is first authenticated and only if
this succeeds does the psk then attempt user authentication.
userLoginSecureExtOrPsk - This selects both the userLoginSecureExt and
psk modes together such that either is allowed to authorized access.
Which mode works for client depends on the client's choice.
ext - Access to the port is denied until the port client is
authenticated (by ext).rw Enumeration .1.3.6.1.4.1.25506.2.75.4.6.4.1.1 |
hh3cDot11SecurityUserLoginTxKeyTypeThis indicates the key type in the 802.1X EAPOL_Key packet.
userLoginTxKeyTypeNone - This means the key type is not set yet.
userLoginTxKeyTypeDot11Key - This selects the 802.11 key type.
userLoginTxKeyTypeRsaRC4Key - This selects the RC4 key for RSA RC4
session encryption.rw Enumeration .1.3.6.1.4.1.25506.2.75.4.6.4.1.2 |
hh3cDot11SecurityPskKeyModeThis is the password input mode. When input as pskKeyModePassPhrase,
hh3cDot11SecurePskKeyString must be 8 to 63 characters; when input as
pskKeyModeRawKey, hh3cDot11SecurePskKeyString must be 64 characters and
each character must be '0'-'9', 'a'-'f' and 'A'-'F'.rw Enumeration .1.3.6.1.4.1.25506.2.75.4.6.4.1.3 |
hh3cDot11SecurityPskKeyStringThis is the password string used for psk authentication.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.6.4.1.4 |
hh3cDot11WlanMeshIfTableThis table is used to configure WLAN mesh interface. SEQUENCE OF Hh3cDot11WlanMeshIfEntry .1.3.6.1.4.1.25506.2.75.4.6.5 |
hh3cDot11WlanMeshIfEntryEach entry contains the WLAN mesh interface configuration. Hh3cDot11WlanMeshIfEntry .1.3.6.1.4.1.25506.2.75.4.6.5.1 |
hh3cDot11WlanMeshIfNumberThis node represents the WLAN mesh interface number. Integer32 .1.3.6.1.4.1.25506.2.75.4.6.5.1.1 |
hh3cDot11WlanMeshIfIndexThis node represents the index of WLAN mesh interface.ro Integer32 .1.3.6.1.4.1.25506.2.75.4.6.5.1.2 |
hh3cDot11WlanMeshRowStatusThis node represents the WLAN mesh interface row status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.6.5.1.3 |
hh3cDot11ACBackupGroup OBJECT IDENTIFIER .1.3.6.1.4.1.25506.2.75.4.7 |
hh3cDot11BackupACAdrssIPThis object represents the backup AC IP address.
If the backup AC IP address is not configured,
the object value is 0.0.0.0.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.25506.2.75.4.7.1 |
hh3cDot11BackupACAdrssIPv6This object represents the backup AC IPv6 address.
If the backup AC IPv6 address is not configured,
the object value is 0::0.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.25506.2.75.4.7.2 |
hh3cDot11RadioElementConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.25506.2.75.4.8 |
hh3cDot11nRadioCfgTableThis table is used to configure dot11n on the radio. SEQUENCE OF Hh3cDot11nRadioCfgEntry .1.3.6.1.4.1.25506.2.75.4.8.1 |
hh3cDot11nRadioCfgEntryThis entry contains the dot11n configuration on the radio. Hh3cDot11nRadioCfgEntry .1.3.6.1.4.1.25506.2.75.4.8.1.1 |
hh3cDot11nRadioCfgIndexRepresents index of the radio. Hh3cDot11RadioElementIndex (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.8.1.1.1 |
hh3cDot11nAMpduEnableEnable the function of A-MPDU.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.8.1.1.2 |
hh3cDot11nAMsduEnableEnable the function of A-MSDU.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.8.1.1.3 |
hh3cDot11nClientDot11nOnlyIf radio type is 802.11an or 802.11gn, only permit clients of 11n mode.
If radio type is 802.11ac, permit clients of 11n and 11ac mode.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.8.1.1.4 |
hh3cDot11nChanelBandSpecify the bandwidth mode.rw Enumeration .1.3.6.1.4.1.25506.2.75.4.8.1.1.5 |
hh3cDot11nShortGiEnableThe function of Short GI.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.8.1.1.6 |
hh3cDot11nClientDot11acOnlyOnly permit clients of 11ac mode.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.8.1.1.7 |
hh3cDot11RadioWDSTableThis table is used to configure WDS on the radio. SEQUENCE OF Hh3cDot11RadioWDSEntry .1.3.6.1.4.1.25506.2.75.4.8.2 |
hh3cDot11RadioWDSEntryEach entry contains the WDS configuration on the radio. Hh3cDot11RadioWDSEntry .1.3.6.1.4.1.25506.2.75.4.8.2.1 |
hh3cDot11RadioWDSIndexRepresents the element index of radio. Hh3cDot11RadioElementIndex (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.8.2.1.1 |
hh3cDot11RadioWDSModeRepresents enable the WDS mode or not.
nowds: The WDS mode is disabled.
wds : The WDS mode is enabledrw Enumeration .1.3.6.1.4.1.25506.2.75.4.8.2.1.2 |
hh3cDot11RadioWDSNetWorkIDRepresents the mesh ID of WDS.rw OCTET STRING .1.3.6.1.4.1.25506.2.75.4.8.2.1.3 |
hh3cDot11WDSSecPskKeyModeRepresents the PSK mode of WDS.rw Enumeration .1.3.6.1.4.1.25506.2.75.4.8.2.1.4 |
hh3cDot11WDSSecPskKeyStringRepresents the PSK value of WDS.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.8.2.1.5 |
hh3cDot11nRadioCfg2TableThis table is used to configure dot11n on the radio. SEQUENCE OF Hh3cDot11nRadioCfg2Entry .1.3.6.1.4.1.25506.2.75.4.8.3 |
hh3cDot11nRadioCfg2EntryThis entry contains the dot11n configuration on the radio. Hh3cDot11nRadioCfg2Entry .1.3.6.1.4.1.25506.2.75.4.8.3.1 |
hh3cDot11nRadioCfg2APIDIndexRepresents index of the AP. Hh3cDot11ObjectIDType (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.8.3.1.1 |
hh3cDot11nRadioCfg2RadioIDIndexRepresents index of the radio. Hh3cDot11RadioScopeType (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.8.3.1.2 |
hh3cDot11nRadioCfg2AMpduEnableEnable the function of A-MPDU.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.8.3.1.3 |
hh3cDot11nRadioCfg2AMsduEnableEnable the function of A-MSDU.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.8.3.1.4 |
hh3cDot11nRadioCfg2ClientDot11nOnlyIf radio type is 802.11an or 802.11gn, only permit clients of 11n mode.
If radio type is 802.11ac, permit clients of 11n and 11ac mode.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.8.3.1.5 |
hh3cDot11nRadioCfg2ChannelBandSpecify the bandwidth mode.rw Enumeration .1.3.6.1.4.1.25506.2.75.4.8.3.1.6 |
hh3cDot11nRadioCfg2ShortGiEnableEnable the function of Short GI.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.8.3.1.7 |
hh3cDot11nRadioCfg2AMpduEnableCMEnable the function of A-MPDU.rw Enumeration .1.3.6.1.4.1.25506.2.75.4.8.3.1.8 |
hh3cDot11nRadioCfg2ChannelBandCMSpecify the bandwidth mode.rw Enumeration .1.3.6.1.4.1.25506.2.75.4.8.3.1.9 |
hh3cDot11nRadioCfg2ShortGiEnableCMEnable the function of Short GI.rw Enumeration .1.3.6.1.4.1.25506.2.75.4.8.3.1.10 |
hh3cDot11nRadioCfg2ClientDot11acOnlyOnly permit clients of 11ac mode.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.8.3.1.11 |
hh3cDot11nRadioCfg2ClientDot11nOnlyCMIf radio type is 802.11an or 802.11gn, permit only clients of 11n mode.
If radio type is 802.11ac, permit clients of both 11n and 11ac mode.rw Hh3cDot11TruthValueCM (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.8.3.1.12 |
hh3cDot11CfgNotifyGroup OBJECT IDENTIFIER .1.3.6.1.4.1.25506.2.75.4.9 |
hh3cDot11CfgNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.25506.2.75.4.9.0 |
hh3cDot11CfgCipherChangeThis notification is sent when cipher type of corresponding service
template is changed. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.2.75.4.9.0.1 |
hh3cDot11CfgPSKChangeThis notification is sent when pre-shared key of corresponding
service template is changed. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.2.75.4.9.0.2 |
hh3cDot11SSIDWepIDConflictTrapThis notification will be sent when the same wep ID is configured
on two service policies. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.2.75.4.9.0.3 |
hh3cDot11CfgTrapVarObjects OBJECT IDENTIFIER .1.3.6.1.4.1.25506.2.75.4.9.1 |
hh3cDot11PreConflictTemplateNumRepresents previous service policy ID when radio bind service policy
and current service policy conflict with previous service policy
in cipher configuration.ro Integer32 .1.3.6.1.4.1.25506.2.75.4.9.1.1 |
hh3cDot11CurrConflictTemplateNumRepresents current service policy ID when radio bind service policy
and current service policy conflict with previous service policy
in cipher configuration.ro Integer32 .1.3.6.1.4.1.25506.2.75.4.9.1.2 |
hh3cDot11ConflictCipherIdxRepresents wep ID that conflicted with.ro Integer32 .1.3.6.1.4.1.25506.2.75.4.9.1.3 |
hh3cDot11ConfigureAPIDRepresents which AP is configured.ro Hh3cDot11ObjectIDType (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.9.1.4 |
hh3cDot11ConfigureRadioIDRepresents which radio in AP is configured.ro Hh3cDot11RadioScopeType (HH3C-DOT11-REF-MIB) .1.3.6.1.4.1.25506.2.75.4.9.1.5 |
hh3cDot11ConfigureAPMacAddressRepresents MAC Address of AP.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.25506.2.75.4.9.1.6 |